2008 Hyundai Tiburon Owners Manual

Do not attempt to adjust the steering wheel while driving as this may result in loss of control of the vehicle and serious injury or death.

CAUTION:

To prevent damage to the goods or the vehicle, care should be taken when carrying fragile or bulky objects in the luggage com- partment.

!

WARNING:

Avoid eye injury. Do not overstretch. Al- ways keep face and body out of recoil path. Do not use when strap has visible signs of wear or damage.

B990A03Y-AAT Floor Mat Anchor

WARNING:

o Make sure the floor mat is properly placed on the floor carpet. If the floor mat slips and interferes with the movement of the pedals during driving, it may cause an accident.

o Don't put an additional floor mat on the top of the anchored mat, otherwise the additional mat may slide forward and interfere with the movement of the ped- als.

FEATURES OF YOUR HYUNDAI

CRUISE CONTROL

B660A02S-AAT (If Installed) Type A

79

Type B

OGK016660

B570A01N

When using a floor mat on the front floor carpet, make sure it attaches to the floor mat anchor in your vehicle. This keeps the floor mat from sliding forward.

OGK018660

1FEATURES OF YOUR HYUNDAI 80

The cruise control system provides automatic speed control for your comfort when driving on freeways, tollroads, or other noncongested highways. This system is designed to function above approximately 25 mph (40 km/h).

B660B01GK-AAT To Set the Cruise Speed Type A

WARNING:

o Cruise control is not recommended for city driving, winding roads, slippery roads, heavy rain, or other bad weather conditions.

o Pay particular attention during the down- hill driving with cruise control system as the vehicle speed can be increased gradu- ally.

Type B

OGK016661

OGK018661

1. Push in the cruise control main switch on the end of the barrel. The "CRUISE" indicator light in the instrument cluster will be illumi- nated. This turns the system on.

2. Accelerate to the desired cruising speed

above 25 mph (40 km/h). 3. Push the control switch downward to "SET (COAST : Type A, ⎯ : Type B)" and release it. The "SET" indicator light in the instrument cluster will illuminate.

4. Remove your foot from the accelerator pedal and the desired speed will automatically be maintained.

5. To momently increase speed, depress the accelerator pedal enough for the vehicle to exceed the preset speed. When you remove your foot from the accelerator pedal, the vehicle will return to the speed you have set.

WARNING:

To avoid accidental cruise control engage- ment, keep the cruise control main switch off when not using the cruise control.

B660C01GK-AAT To Cancel the Cruise Speed Type A

To disengage the cruise control system, pull the control switch toward the steering wheel to "CANCEL" position. Additionally, the following actions will disengage the system :

B660D01E-AAT To Resume the Preset Speed Type A

FEATURES OF YOUR HYUNDAI

81

o Depress the brake pedal. o Depress the clutch pedal (Manual transaxle). o Shift the selector lever to "N" position (Auto-

matic transaxle).

o Decrease the vehicle speed lower than the

memorized speed by 9 mph (15 km/h).

o Decrease the vehicle speed to less than 25

mph (40 km/h).

o Release the main switch.

Type B

Type B

OGK016662

OGK016663

OGK018662

OGK018663

1FEATURES OF YOUR HYUNDAI 82

The vehicle will automatically resume the speed set prior to cancellation when you push the control switch upward to "RESUME (ACCEL : Type A, + : Type B)" position and release it, providing the vehicle speed is above 25 mph (40
km/h).

B660F03E-AAT To Reset at a Slower Speed Type A

1. Push the control switch downward to "SET (COAST : Type A, ⎯ : Type B)" and hold it. The vehicle will decelerate.

2. When the desired speed is obtained, release the control switch. While the control switch is pushed, the vehicle speed will gradually decrease.

B660E01E-AAT To Reset at a Faster Speed

1. Push the control switch upward to "RE- SUME (ACCEL : Type A, + : Type B)" position and hold it.

2. Accelerate to desired speed and release the control switch. While the control switch is held, the vehicle will gradually gain speed.

Type B

OGK016661

OGK018661

WARNING:

o Keep the cruise control ON/OFF switch off when not using the cruise control to avoid inadvertently setting a speed.

o Use the cruise control system only when traveling on open highways in good weather.

o Do not use the cruise control when it may not be safe to keep the car at a constant speed, for instance, driving in heavy or varying traffic, or on slippery (rainy, icy or snow-covered) or winding roads or over 6% up-hill or down-hill roads.

o Pay particular attention to the driving conditions whenever using the cruise control system.

o During cruise-control driving with a manual transaxle vehicle, do not shift into neutral without depressing the clutch pedal, or the engine will be overrevved. If this happens, depress the clutch pedal or release the main switch.

!

WARNING:

o With the cruise control engaged, when the brake pedal is applied, it is normal to hear the cruise control system deacti- vate. This is an indication of normal system operation. o During normal cruise control operation, when the "SET(COAST : Type A, ⎯⎯⎯⎯⎯ : Type B)" is activated or reactivated after applying the brakes, the cruise control will energize after approximately 3 sec- onds. This delay is normal.

AUDIO REMOTE CONTROL SWITCH B610A02GK-GAT (If installed)

POWER ON/OFF Switch

FEATURES OF YOUR HYUNDAI

83

SEEK (UP / ) Switch

Press the SEEK UP ( ) switch 1 sec. or more.

1. RADIO mode

When the SEEK UP ( ) switch is pressed, the unit will automatically tune to the next higher frequency.

2. TAPE mode

Pressing the SEEK UP ( ) switch will play the beginning of the next music segment.

OGK046086L

3. CD (compact disc)/CDC

(compact disc changer) mode

Press the POWER ON/OFF switch to select Radio, Tape, CD (compact disc) and CDC (compact disc changer).

Press the POWER ON/OFF switch once again to cancel Radio, Tape, CD (compact disc) and CDC (compact disc changer).

Press the SEEK UP ( ) switch once to skip forward to the beginning of the next track.

VOL ( / ) Switch

o Press the VOL ( ) button to increase

o Press the VOL ( ) button to decrease

volume.

volume.

1FEATURES OF YOUR HYUNDAI 84

HEATING AND COOLING CONTROL

B710A02GK-GAT

1. Side Defrost Nozzle 2. Side Ventilator 3. Windshield Defrost Nozzle 4. Center Ventilator

OGK016003

B710B02O-AAT Center Ventilator

The center ventilators are located in the middle of the dashboard. To change the direction of the air flow, move the knob in the center of the vent up-and-down and side-to-side. The vents are opened when the vent knob is moved to " " position. The vents are closed when the vent knob is moved to " ". Keep these vents clear of any obstructions.

B710C01JM-AAT Side Ventilator

The side ventilators are located on each side of the dash board. To change the direction of the air flow, move the knob in the center of the vent up-and-down and side-to-side. The vents are opened when the vent knob is moved to " " position. The vents are closed when the vent knob is moved to " ". Keep these vents clear of any obstructions.

HEATING AND VENTILATION

FEATURES OF YOUR HYUNDAI

85

B670A01GK-GAT Rotary Type (If Installed)

B670B01GK-AAT Fan Speed Control (Blower Control)

B670E02A-AAT Temperature Control

1. Temperature control switch 2. Air intake control switch 3. Air flow control switch 4. Air Conditioning switch 5. Fan speed control switch 6. Rear window defroster switch

OGK046038N

OGK046045N

This is used to select the fan speed. This blower fan speed, and therefore the vol- ume of air delivered from the system, may be controlled manually by setting the blower con- trol between the "1" and "4" positions.

Cool

Warm

OGK046043

This control is used to adjust the degree of heating or cooling desired.

1FEATURES OF YOUR HYUNDAI 86

B670C02Y-AAT Air Intake Control

B670D04O-AAT Air Flow Control

NOTE: It should be noted that prolonged opera- tion of the heating system in " " mode will give rise to fogging of the windshield and side windows and the air within the passenger compartment will become stale. In addition prolonged use of the air condi- tioning with the " " mode selected may result in the air within the passenger com- partment becoming excessively dry.

This is used to select fresh outside air or recirculation of inside air.

OGK046044

Fresh Recirculation

With the " " mode selected, air enters the vehicle from outside and is heated or cooled according to the other functions selected. With the " " mode selected, air from within the passenger compartment is drawn through the heating system and heated or cooled ac- cording to the other functions selected.

OGK046039N This is used to turn the blower fan on/off and to direct the flow of air. Air can be directed to the floor, dashboard outlets, or windshield. Five symbols are used to represent Face, Bi-Level, Floor, Floor-Defrost and Defrost air position. The MAX A/C mode is used to cool the inside of the vehicle faster. The "OFF" mode is used to turn the blower fan off.

NOTE: If the blower fan is off, the air intake control is set to the fresh mode automatically.

FEATURES OF YOUR HYUNDAI

87

OGK016095

OGK016096

OGK016097

Face-Level

Bi-Level

Floor-Level

Selecting the "Face" mode will cause air to be discharged through the side and center venti- lators.

Air is discharged through the face vents and the floor vents. This makes it possible to have cooler air from the dashboard vents and warmer air from the floor outlets at the same time.

Air is discharged through the floor vents, wind- shield defroster nozzle, side defroster nozzle and side ventilator. If the "Floor" mode is selected, the "Fresh" mode will be activated.

1FEATURES OF YOUR HYUNDAI 88

mode except the defrost mode and the floor-defrost mode. Although the A/C switch indicator is turned off, this is normal operation.

OGK016098

OGK016099

Floor-Defrost Level

Defrost-Level

Air is discharged through the windshield defrost nozzle, the floor vents, side defroster nozzle, side ventilator. If the "Floor-Defrost" mode is selected, the A/C will be turn on automatically and "Fresh" mode will be activated.

Air is discharged through the windshield defrost nozzle, side defroster nozzle, side ventilator. If the "Defrost" mode is selected, the A/C will turn on automatically and "Fresh" mode will be activated.

NOTE: If the "Floor-Defrost" or "Defrost" mode is selected, the air conditioning will not turn off by pushing the A/C button. If the air flow control is set to the defrost or the floor-defrost mode, the A/C will be on automatically and the A/C will not off until the air flow control is set to the another

OGK016103

MAX A/C-Level

Air is discharged through the face level vents. If the "MAX A/C" mode is selected, the A/C will turn on automatically and "Recirculation" mode will be activated.

NOTE: o The air intake control switch will change to " " mode when the ignition switch is turned "ON" with the MAX A/C mode selected.

o When you change to another mode from MAX A/C, the A/C and the air intake control switch are set to the following chart.

Air Intake

Control Switch

or *

A/C

ON

ON or OFF *

ON or OFF *

ON

ON

* The A/C or the air intake control switch return

to its former setting.

FEATURES OF YOUR HYUNDAI

HEATING CONTROLS

B690A02S-AAT

89

OGK016095N

OFF-Level

Air is discharged through the windshield de- froster nozzle, side defroster nozzle and side ventilator.

NOTE: If the air flow control is off, the air intake control is set to the fresh mode automati- cally.

OGK046038A

For normal heating operation, set the air intake control to the fresh air ( ) position and the air flow control to the floor (

) position.

For faster heating, the air intake control switch ) position. should be set in the recirculate (

If the windows fog up, set the air flow control to the defrost ( ) position. (The A/C will turn on automatically and "Fresh" mode will be acti- vated.)

For maximum heat, move the temperature con- trol to "Warm".

1FEATURES OF YOUR HYUNDAI BI-LEVEL HEATING 90

VENTILATION

AIR CONDITIONING SYSTEM

B700A02A-AAT

B710A01A-AAT

B740A01S-AAT Air Conditioning Switch (If installed)

OGK016700N

OGK016701N

Your Hyundai is equipped with bi-level heating controls. This makes it possible to have cooler air from the dashboard vents and warmer air from the floor outlets at the same time. To use this feature:

o Set the air intake control switch to the fresh

air (

) position.

o Set the air flow control at the bi-level (

o Adjust the fan speed control to the desired

o Set the temperature control between "Cool"

position.

speed.

and "Warm".

To operate the ventilation system:

o Set the air intake control switch at the fresh

air (

) position.

o To direct all intake air to the dashboard vents, ) position. o Adjust the fan speed control to the desired

set the airflow control to the face (

o Set the temperature control between "Cool"

speed.

and "Warm".

OGK046047

The air conditioning is turned on or off by pushing the A/C button on the heating/air con- ditioning control panel.

B740B02GK-AAT Air Conditioning Operation Cooling

o Adjust the fan control to the desired speed. For greater cooling, turn the fan control to one of the higher speeds or temporarily select the recirculate ( ) position on the air intake control switch.

B740C01GKA-AAT Dehumidified Heating

FEATURES OF YOUR HYUNDAI

91

OGK016704N To use the air conditioning to cool the interior:

o Adjust the air flow control to the desired

position.

o Turn on the air conditioning switch by push- ing in on the switch. The air conditioning indicator light should come on at the same time.

o Set the air intake control switch to the fresh

air (

) position.

o Adjust the fan control to the desired position. o Set the temperature control to "Cool". ("Cool" provides maximum cooling. The tempera- ture may be moderated by moving the con- trol toward "Warm".)

For dehumidified heating:

OGK016705N

o Adjust the air flow control to the desired

position.

o Turn on the air conditioning switch. The air conditioning indicator light should come on at the same time.

o Set the air intake control switch to the fresh

air (

) position.

o Set the air flow control to the face (

position.

o Adjust the fan control to the desired speed. o For more rapid action, set the fan at one of

the higher speeds.

o Adjust the temperature control to provide the

desired amount of warmth.

1FEATURES OF YOUR HYUNDAI 92

B740D01A-AAT Operation Tips

o If the interior of the car is hot when you first get in, open the windows for a few minutes to expel the hot air.

o When you are using the air conditioning system, keep all windows closed to keep hot air out.

o When moving slowly, as in heavy traffic, shift to a lower gear. This increases engine speed, which in turn increases the speed of the air conditioning compressor.

o On steep grades, turn the air conditioning off to avoid the possibility of the engine over- heating.

o During winter months or in periods when the air conditioning is not used regularly, run the air conditioning once every month for a few minutes. This will help circulate the lubri- cants and keep your system in peak oper- ating condition.

DEFROSTING/DEFOGGING

B720A02E-AAT

A Type

B Type

A Type

B Type

FEATURES OF YOUR HYUNDAI

93

OGK016800N

OGK016801N

Use the heating/ventilation system to defrost or defog the windshield:

To remove interior fog on the windshield; o Set the air flow control to the defrost ( ) position. (The A/C will turn on automatically and the "Fresh" mode will be activated.)

o Set the temperature control to the desired position. o Set the fan speed control between "1" and "4" position.

To remove frost or exterior fog on the windshield; o Set the air flow control to the defrost ( ) position. (The A/C will turn on automatically and the "Fresh" mode will be activated.)

o Set the temperature control to warm. o Set the fan speed control to position "3" or "4".

NOTE: When the A/C is operated continuously on the floor-defrost level ( ) or defrost level ( ), it may cause fog to form on the exterior windshield. If this occurs, set the air flow control to the face level position ( ) and fan speed control to the low position.

1FEATURES OF YOUR HYUNDAI 94

AUTOMATIC HEATING AND COOLING CONTROL SYSTEM

B970A01Y-AAT (If lnstalled)

B970B04GK-GAT Heating and Cooling Controls

Your Hyundai is equipped with an automatic heating and cooling control system controlled by simply setting the desired temperature.

OGK046057C

1. Temperature Control 2. Display Window 3. Blower Fan Control 4. AUTO (Automatic Control)Switch 5. Air Flow Control Switch

6. Air Conditioning Switch 7. Defroster Switch 8. Rear Window Defroster Switch 9. Air lntake Control Switch 10. OFF Switch

FEATURES OF YOUR HYUNDAI

95

NOTE: If the battery has been discharged or dis- connected, the temperature mode will reset to Centigrade degrees. This is a normal condition and you can change the temperature mode from Centi- grade to Fahrenheit as follows; Press the "OFF" and "AUTO " switch simul- taneously for 3 seconds. The display shows that the unit of tempera- ture is adjusted to Centigrade or Fahrenheit (°C →→→→→ °F or °F →→→→→ °C).

B970C01GK-GAT Automatic Operation

OGK046058

The FATC (Full Automatic Temperature Con- trol) system automatically controls heating and cooling by doing as follows:

1. Push the "AUTO" switch. The display "AUTO" will illuminate confirming that the Face, Floor and/or Bi-Level modes as well as the blower speed and air conditioner will be controlled automatically.

OGK046061

2. Turn the "TEMP" knob to set the desired

temperature. The temperature will increase to the maxi- mum 32°C(90°F) by turning the knob clock- wise. The temperature will decrease to the mini- mum 17°C(62°F) by turning the knob coun- terclockwise.

1FEATURES OF YOUR HYUNDAI 96

B995A01GK-GAT Outside Temperature Switch

B980A01Y-AAT Manual Operation

The heating and cooling system can be con- trolled manually as well by pushing buttons other than the "AUTO" button. In this state, the system sequentially works according to the order of buttons selected. The function of the buttons which are not se- lected will be controlled automatically. Press the "AUTO" button in order to convert to automatic control of the system.

Photo Sensor

OGK026223C

NOTE: Never place anything over the sensor which is located on the instrument panel to en- sure better control of the heating and cool- ing system.

OGK046066

Press the button, the display show that the unit of outside temperature is adjusted to centigrade or fahrenheit (°C → °F or °F → °C).

B980B01Y-AAT Fan Speed Control Switch

B670C02GK-AAT Air Intake Control Switch This is used to select fresh outside air or recirculation inside air. To change the air intake control mode, (Fresh mode, Recirculation mode) push the control button.

FEATURES OF YOUR HYUNDAI

97

OGK046064

The fan speed can be set to the desired speed by turning the fan speed control knob. The higher the fan speed is, the more air is delivered. Pressing the "OFF" switch turns off the fan.

OGK046062L

RECIRCULATION MODE ( ) : The indica- tor light on the button is illuminated when the air intake control is in recirculation mode.

OGK046063L

With the "Fresh" mode selected, air enters the vehicle from the outside and is heated or cooled according to the function selected.

FRESH MODE ( ) : The indicator light on the button goes on when the air intake control is in fresh mode.

With the "Recirculation" mode selected, air from within the passenger compartment will be drawn through the heating system and heated or cooled according to the function selected.

1FEATURES OF YOUR HYUNDAI 98

NOTE: It should be noted that prolonged opera- tion of the heating system in "recirculation" mode will give rise to fogging of the wind- shield and side windows and the air within the passenger compartment will become stale. In addition, prolonged use of the air conditioning with the "Recirculation" mode selected may result in the air within the passenger compartment becoming exces- sively dry.

B740A01S-AAT Air Conditioning Switch

B980D01Y-AAT Heating and Cooling System Off

The air conditioning is turned on or off by pushing the A/C button on the heating/air con- ditioning control panel.

OGK046065

OGK046067
Press the "OFF" button to stop the operation of the heating and cooling system.

B980E01GK-GAT Air Flow Control

FEATURES OF YOUR HYUNDAI

99

OGK046059
This is used to direct the flow of air. Air can be directed to the floor, instrument panel outlets, or windshield. Four symbols are used to represent Face, Bi-Level, Floor and Floor-Defrost air position.

Face-Level

Bi-Level

OGK016095

OGK016096

When selecting the "Face" mode, the indicator light will come on, causing air to be discharged through the face level vents.

When selecting the "Bi-Level" mode, the indica- tor light will come on and the air will be dis- charged through the face vents and the floor vents. This makes it possible to have cooler air from the dashboard vents and warmer air from the floor outlets at the same time.

1FEATURES OF YOUR HYUNDAI 100

B980F01GK-AAT Defrost Switch

OGK016097

OGK016098

Floor-Level

When selecting the "Floor-Level" mode, the indicator light will come on and the air will be discharged through the floor vents, windshield defroster nozzle, side defroster nozzle, side ventilator.

Floor-Defrost Level

When selecting the "Floor-Defrost" mode, the indicator light will come on and the air will be discharged through the windshield defrost nozzle, the floor vents, side defroster nozzle, side ventilator.

OGK046060
When the "Defrost" button is pressed, the " " mode will be automatically selected and the air will be discharged through the windshield de- frost vents. To assist in defrosting, the air conditioning will operate if ambient temperature is higher than 35.6°F (2°C) and automatically turns off if the ambient temperature drops below 32.9 °F (0.5 °C).

FEATURES OF YOUR HYUNDAI

101

CLIMATE CONTROL AIR FILTER (IN FRONT OF BLOWER UNIT)

B760A06GK-AAT

Outside air

Inside air

Filter

Inside air

Blower fan

Evaporator core

Heater core

B760A01E

The climate control air filter is located in front of the blower unit behind the glove box. It operates to decrease the amount of pollutants entering the car. To replace the climate control air filter, refer to the page 6-16.

CAUTION:

o Replace the filter every 10,000 miles (15,000 km) or once a year. If the car is being driven in severe conditions such as dusty, rough roads, more frequent climate control air filter inspections and changes are required.

o When the air flow rate is decreased, the system should be checked at an autho- rized dealer.

1FEATURES OF YOUR HYUNDAI 102

STEREO SOUND SYSTEM

B750A02A-AAT How Car Audio Works FM reception

Ionosphere

B750A01L AM and FM radio signals are broadcast from transmitter towers located around your city. They are intercepted by the radio antenna on your car. This signal is then received by the radio and sent to your car speakers. When a strong radio signal has reached your vehicle, the precise engineering of your audio system ensures the best possible quality repro- duction. However, in some cases the signal coming to your vehicle may not be strong and clear. This can be due to factors such as the distance from the radio station, closeness of other strong radio stations or the presence of buildings, bridges or other large obstructions in the area.

AM reception

Ionosphere

FM radio station

Mountains

Unobstructed

area

B750A02L AM broadcasts can be received at greater distances than FM broadcasts. This is because AM radio waves are transmitted at low frequen- cies. These long, low frequency radio waves can follow the curvature of the earth rather than travelling straight out into the atmosphere. In addition, they curve around obstructions so that they can provide better signal coverage.

Buildings

Obstructed area

Iron bridges

B750A03L

FM broadcasts are transmitted at high frequen- cies and do not bend to follow the earth's surface. Because of this, FM broadcasts gen- erally begin to fade at short distances from the station. Also, FM signals are easily affected by buildings, mountains, or other obstructions. These can result in certain listening conditions which might lead you to believe a problem exists with your radio. The following conditions are normal and do not indicate radio trouble:

FEATURES OF YOUR HYUNDAI

103

B750B05Y-AAT Using a cellular phone or a two-way radio

When a cellular phone is used inside the vehicle, noise may be produced from the audio equip- ment. This does not mean that something is wrong with the audio equipment. In such a case, use the cellular phone at a place as far as possible from the audio equipment.

WARNING:

Hyundai recommends that you never use a cell phone while driving. This could result in loss of control, and an accident that may cause death, serious injury, or property damage. You must stop at a safe place to use a cellular phone.

NOTE: Some states and cities have regulations prohibiting the use of cell phones while driving. You should be aware of the specific requirements in your area.

B750A04L

B750A05L

o Fading - As your car moves away from the radio station, the signal will weaken and sound will begin to fade. When this occurs, we suggest that you select another stronger station.

o Flutter/Static - Weak FM signals or large obstructions between the transmitter and your radio can disturb the signal causing static or fluttering noises to occur. Reducing the treble level may lessen this effect until the disturbance clears.

o Station Swapping - As an FM signal weak- ens, another more powerful signal near the same frequency may begin to play. This is because your radio is designed to lock onto the clearest signal. If this occurs, select another station with a stronger signal.

o Multi-Path Cancellation - Radio signals being received from several directions can cause distortion or fluttering. This can be caused by a direct and reflected signal from the same station, or by signals from two stations with close frequencies. If this occurs, select another station until the condition has passed.

1FEATURES OF YOUR HYUNDAI 104

ANTENNA

B870A01A-GAT Fixed Rod Antenna

B870D01Y-GAT Glass Antenna (If Installed)

CAUTION:

o Do not clean the inner side of the rear window glass with an abrasive type of glass cleaner or use a scraper to remove foreign deposits from the inner surface of the glass as this may cause damage to the antenna elements.

o Avoid adding metallic coating (Such as Ni, Cd, and so on). These can disturb receiving AM and FM broadcast signals.

B870A01A Your car uses a fixed rod antenna to receive both AM and FM broadcast signals. This antenna is a removable type. To remove the antenna, turn the antenna counterclock- wise. To install the antenna, turn the antenna clockwise.

OGK046085

When the radio power switch is turned on while the ignition key is in either the "ON" or "ACC" position, your car will receive both AM and FM broadcast signals through the antenna in the rear window glass.

CAUTION:

Be sure to remove the antenna before wash- ing the car in an automatic car wash or the antenna may be damaged.

AUDIO SYSTEM

H280A01GK-GAT Stereo Radio Operation (H280) (If Installed)

FEATURES OF YOUR HYUNDAI

105

1, 2

10

GK_280_NA

1. 2. Power Button and Volume Control 3. Radio Band Selection Button 4. SCAN Button 5. Automatic Channel Selection Button 6. Preset Button 7. Information Display Screen (LCD) 8. AUDIO Select Button 9. Manual Channel Selection Control (TUNE

Control)

10. EQ Button

1FEATURES OF YOUR HYUNDAI 106

H280B01GK-GAT 1. Power Button (POWER ON)

Press this button when the ignition switch of the automobile is set to ACC (1st notch) or ON (2nd notch) to turn on the power and the audio system. Press once again when the audio system is on to turn off the power.

2. Volume Control (VOLUME)

Turn the volume control clockwise to increase volume and counterclockwise to reduce. The volume level will be displayed on the screen when you adjust the volume.

3. Radio Band Selection Button (FM/AM)

o Press this button to listen to either FM or AM. o The radio will be set to each of the following

modes each time you press the button. FM1 ➟ FM2 ➟ AM

NOTE: Push this button when the power is off to turn on the power automatically.

4. SCAN Button

Press this button to automatically select chan- nels starting from the current channel and play each channel for 5 seconds.

5. Automatic Channel Selection Button

(SEEK)

Press the upper side of the button to automati- cally increase frequency and select and play the receivable channel. Press the lower side of the button to automatically decrease frequency and select and play the next available channel.

6. Preset Button (1~6)

Press this button to listen to the channels memorized to each button. If you want to memo- rize the current channel to the preset button, press the button for more than 1.5 seconds then the channel will be memorized to the button with a beep.

7. Information Display Screen (LCD)

A variety of information will be displayed on the screen including the radio bands (FM1/FM2/ AM) while listening to the radio, frequency of each channel, the number of preset channel and "ST" for FM stereo broadcasting.

8. AUDIO Select Button Press this button to control tone. Each time you press the button, the mode will switch from BASS ➟ MIDDLE ➟ TREBLE ➟ FADER ➟ BALANCE and the mode will be displayed on the screen.

BASS

MIDDLE

TREBLE

BALANCE

FADER

Turn the TUNE Controller clockwise to increase bass tone and counterclockwise to decrease.

Turn the TUNE Controller clockwise to increase middle tone and counter- clockwise to decrease.

Turn the TUNE Controller clockwise to increase treble tone and counter- clockwise to decrease.

Turn the TUNE Controller clockwise to increase right speaker volume and coun- terclockwise to increase left speaker volume.

Turn the TUNE Controller clockwise to increase rear speaker volume and coun- terclockwise to increase front speaker volume.

FEATURES OF YOUR HYUNDAI

107

9. Manual Channel Selection Control

(TUNE)

Turn this controller while listening to the radio to manually adjust frequency. Turn clockwise to increase frequency and counterclockwise to reduce frequency.

10. EQ Button Each time you press this button the sound equalizer setting will switch from POP ➟ JAZZ ➟ ROCK ➟ CLASSIC ➟ OFF (Not displayed).

CAUTION:

o Do not place beverages close to the audio system. The audio system mecha- nism may be damaged if you spill them. o Do not strike or allow anything to impact the audio system, damage to the system mechanisms could occur.

1FEATURES OF YOUR HYUNDAI 108

H280C01GK-GAT Cassette Tape Player Operation (H280) (If Installed)

1. TAPE MODE Selection Button / TAPE

Side Selection Button 2. Cassette Tape Deck 3. Tape Eject Button 4. DOLBY Selection Button 5. Fast Rewind 6. Fast Forward 7. Automatic Previous Track Selection Button 8. Automatic Next Track Selection Button 9. Section Repeat Button (REPEAT) 10. Information Display Screen (LCD)

10

GK_280_NA

H280D01GK-GAT 1. TAPE MODE Selection Button / TAPE

Side Selection Button

Press this button to turn to the TAPE mode. The system will play the tape if the tape is inside the deck and turn off CD or radio if either mode was on. If you press this button while the tape is being played, the other side of the tape will be played. The screen will display "PLAY" along with the direction of play.

2. Cassette Tape Deck (Tape Insert) When you insert the tape, push it into the deck while the side of tape you want to listen to face upward. If the ignition switch of the automobile is set to ACC (1st notch) or ON (2nd notch), the tape will be automatically played when you insert it even if the power of the audio system is off.

3. Tape EJECT Button

Press this button while the tape is being played to eject the tape. This will eject the tape even when the ignition switch of the automobile is set to OFF.

NOTE: Push this button to turn the power on automatically when the TAPE is inside and the power is off.

4. DOLBY Selection Button

8. Automatic Next Track Selection But-

FEATURES OF YOUR HYUNDAI

109

Press this button when you play Dolbyized type to reduce noise in the medium to high bands due to Dolby effect. The screen will display " " The " mark will disappear when you press it again.

5. Fast Rewind (REW)

Press [REW] button while playing the tape to rewind the tape to the beginning and the screen will display "REW." Press it again while rewind- ing to play from the current position.

6. Fast Forward (FF) Press [FF] button while playing the tape to wind the tape to the end and the screen will display "FF." Press it again while winding to play from the current position.

7. Automatic Previous Track Selection

Button (TRACK DOWN)

Press [TRACK ] button to rewind the tape to the beginning of the song you are listening to. While rewinding the tape, the screen will display "AMS." Press the button again while rewinding the tape to play from the current position.

ton (TRACK UP)

Press [SEEK ] button to wind the tape to the beginning of the song next to the song you are listening to. While winding the tape, the screen will display "AMS." Press the button again while winding the tape to play from the current posi- tion.

9. Section Repeat Button (RPT) Press [RPT] button to repeat the song you are listening to.

10. Information Display Screen (LCD) Various status of cassette tape will be displayed on the screen while listening to the tape such as "PLAY" while playing the tape, the direction of play " ", "FF" and "REW" for fast forward and rewind, "METAL" for playing metal tapes as well as "DOLBY" and "RPT."

or

CAUTION:

o Do not insert anything like coins into the player slot as damage to the unit may occur.

o Do not place beverages close to the audio system. The playback mechanism may be damaged if you spill them.

o Do not strike or allow anything to impact the audio system, damage to the system mechanisms could occur.

1FEATURES OF YOUR HYUNDAI 110

H280E01GK-GAT Compact Disc Player Operation (H280) (If installed)

10

12

11

13

1. CD Deck 2. CD Indicator 3. CD EJECT Button 4. CD Selection Button 5. Fast Backward 6. Fast Forward 7. Automatic Previous Track Selection Button 8. Automatic Next Track Selection Button 9. Section Repeat Button 10. Information Display Screen (LCD) 11. BOOKMAKR Button 12. RDM (Random) Button 13. SCROLL Button 14. FILE Search Knob 15. Directory Search Button 16. SCAN Button

16

14

15

GK_280_NA

FEATURES OF YOUR HYUNDAI

111

H280F01GK-GAT 1. CD Deck

Make sure the printed side of the disk faces upward when you insert the disk. If you insert the disk when the ignition switch of the automo- bile is set to ACC (1st notch) or ON (2nd notch), the CD Deck will automatically play CD even if the power was off. This CD Deck can play both 12cm and 8cm audio disks. If you insert video CD, then the screen will display "ERROR DISC" and eject the disk.

2. CD Indicator

This indicator light will be on if the CD is inside the CDP deck whether the audio system is on or not. This light will go off when the CD is ejected.

3. CD Eject Button

Press [ ] button to eject the disk while playing the disk. This will eject the CD whether or not the ignition switch is on or off.

4. CD Selection Button

Press this button while the disk is inside the CDP deck to listen to the CD even if the radio or tape was on or if CD changer was in action. If you press [CD/MP3] button when the disk is ejected and hanging in the opening, the system will automatically insert the disk and play the CD.

5. Fast Backward (REW)

8. Automatic Next Track Selection But-

Press and hold [REW] button while playing CD then the player will play the disk backwards 5
times the regular speed for first 5 seconds and 15 times faster after that. The sound will be reduced by 12dB while you are holding the button.

6. Fast Forward (FF)

Press and hold [FF] button while playing CD then the player will play the disk forward 5 times the regular speed for first 5 seconds and 15
times faster after that. The sound will be re- duced by 12dB while you are holding the button.

NOTE: If you press this button when the power is off and CD is inside the deck, the power will be automatically turned on.

7. Automatic Previous Track Selection

Button

Press [TRACK ] button to go to the beginning of the song you are listening to while playing the CD. Press the button again to go to the beginning of the song before the song you were listening to. When you press this button while listening to the first track of the CD then the system will move to the beginning of the last track of the CD.

ton

Press [SEEK ] button to go to the beginning of the song next to the song you are listening to while playing the CD.

9. Section Repeat Button (RPT)

Press [RPT] button to repeat the song you are listening to. Press this button again to cancel repetition.

10. Information Display Screen (LCD) Various status of the CD will be displayed on the screen while listening to the CD such as "CD" while playing the CD, the track title and number, RPT, RDM and MARK.

11. BOOKMARK Button This button lets you select the songs you want to listen to in the CD. Move to the track and press [MARK] for more than 1 second then the screen will display "M" and select the track. Press the button less than 1 second to play the songs you selected and the system will display "M"

12. RDM (Random) Button Press [RDM] button to play the songs in random order.

NOTE: When you use CD-R or CD-RW, the CD may not be played due to the manufacturing method of CD makers and the recording method of the user. In this case, change CD unless the continuous use of such CDs may cause damage to the system.

1FEATURES OF YOUR HYUNDAI 112

13. SCROLL Button If the title of MP3 or WMA file is too long, press this button to scroll the entire song title on the LCD screen.

14. FILE Search Knob Turn this knob to the left and right while listening to CD to change track number. If you press the button within 5 seconds then the selected track will be played. If you do not press the button within 5 seconds then it will display the currently played track.

15. Directory Search Button In case the MP3/WMA CD contains more than 2 folders, press this button up and down to search each directory. You can move to the directory and turn the search knob to search through the tracks. If you do not press the knob within 5 seconds after you select a track then the system will automatically return to the cur- rent track.

16. SCAN Button If you press this button, the player will play 10
seconds of each track. Press it again to cancel scanning.

CAUTION:

o Do not insert warped or poor quality discs into the CD player as damage to the unit may occur.

o Do not insert anything like coins into the player slot as damage to the unit may occur.

o Do not place beverages close to the audio system. The playback mechanism may be damaged if you spill them.

o Do not strike or allow anything to impact the audio system, damage to the system mechanisms could occur.

o Off-road or rough surface driving may cause the compact disc to skip. Do not use the compact disc when driving in such conditions as damage to the com- pact disc face could occur.

o Do not attempt to grab or pull the com- pact disc out while the disc is being pulled into the audio unit by the self- loading mechanism. Damage to the audio unit and compact disc could oc- cur.

o Avoid using recorded compact discs in your audio unit. Original compact discs are recommended.

H265A01GK-GAT Stereo Radio Operation (H265) (If installed)

FEATURES OF YOUR HYUNDAI

113

GK_265_NA

1. Power Button and Volume Control (Power

On / Volume)

2. Radio Band Selection Button 3. Automatic Channel Selection

Button(SEEK)

4. Manual Channel Selection Control (TUNE) 5. Preset Button 6. Information Display Screen (LCD) 7. SCAN Button 8. AUDIO Select Button

1FEATURES OF YOUR HYUNDAI 114

H265B01GK-GAT 1. Power Button and Volume Control

(POWER ON/ VOLUME)

Press this button when the ignition switch of the automobile is set to ACC (1st notch) or ON (2nd notch) to turn on the power of the audio system. When the power is turned on, turn the volume control clockwise to increase volume and coun- terclockwise to reduce. Press once again when the audio system is on to turn off the power.

2. Radio Band Selection Button (FM/AM) North American Standard o Press this button to listen to either FM or AM. o The radio will be set to each mode each time loop;

you press FM1➟FM2➟AM➟FM1 and soon.

the button

in a

European Standard o Press this button to listen to either FM or AM. o The radio will be set to each mode each time loop;

you press FM1➟FM2➟MW➟LW➟FM1 and soon.

the button

in a

3. Automatic Channel Selection Button

5. Preset Button (1~6)

(SEEK)

Press and hold the [ ] button for more than 0.5
seconds until you hear the beep to automatically increase frequency and press and hold the [ ] button for more than 0.5 seconds until you hear the beep to automatically decrease frequency to select and play the next available channel. If the received channel is memorized in the preset buttons then the screen will display the memo- rized channel.

4. Manual Channel Selection Control

(TUNE)

] to decrease.

Press and hold [ ] button for less than 0.5
seconds to increase frequency by 1 step and Press and hold [ ] button for more than 0.5 seconds even after you hear the beep then the frequency will increase or decrease quickly. When you release the button, the system will turn to the automatic selection mode.

] or [

Press this button but do not hold for no more than 2 seconds to listen to the channels memorized to each button. If you want to memorize the current channel to the preset button when you are listening to channel not memorized to any of the preset buttons, press the button and hold for more than 2 seconds then the channel will be memorized to the button with the beep.

6. Information Display Screen (LCD)

A variety of information will be displayed on the screen including the radio bands (FM1/FM2/ AM) while listening to the radio, frequency of each channel, the number of preset channel and "ST" for FM stereo broadcasting.

7. Automatic Channel Scan Button

Press this button to automatically select next available channel and play the channel for 5
seconds and continuously move to the next available channel and play. Press again when you find the channel you would like to listen to while scanning, press the button again to stop scanning and continue to listen to the channel you selected. And continue to listen to the current channel.

FEATURES OF YOUR HYUNDAI

115

Turn the TUNE Controller clockwise to increase rear speaker volume and coun- terclockwise to increase front speaker volume.

CAUTION:

o Do not place beverages close to the audio system. The audio system mecha- nism may be damaged if you spill them. o Do not strike or allow anything to impact the audio system, damage to the system mechanisms could occur.

8. AUDIO Select Button

FADER

o Press this button to change AUDIO function

control mode.

Current State➟BASS➟MID➟TRE➟ FAD➟BAL o Select the audio control mode you want and increase or decrease the setting by ±10 from currently audio control mode. If no actions are taken, the screen will return to the pre- vious display after 3 seconds.

BASS

MIDDLE

TREBLE

BALANCE

Turn the TUNE Controller clockwise to increase bass tone and counterclockwise to decrease.

Turn the TUNE Controller clockwise to increase middle tone and counter- clockwise to decrease.

Turn the TUNE Controller clockwise to increase treble tone and counter- clockwise to decrease.

Turn the TUNE Controller clockwise to increase right speaker volume and coun- terclockwise to increase left speaker volume.

1FEATURES OF YOUR HYUNDAI 116

H265C01GK-GAT Compact Disc Player Operation (H265) (If installed)

11

10

1. CD DECK 2. CD INDICATOR 3. CD Disc EJECT Button 4. CD Selection Button 5. Fast Backward 6. Fast Forward 7. Automatic Previous Track Selection Button 8. Automatic Next Track Selection Button 9. Section Repeat Button 10. Information Display Screen (LCD) 11. SCAN Button

GK_265_NA

H265D01GK-GAT 1. CD Deck

Make sure the printed side of the disk faces upward when you insert the disk. If you insert the disk when the ignition switch of the automo- bile is set to ACC (1st notch) or ON (2nd notch), the CD DECK will automatically play CD even if the power was off. This CD DECK can play both 12cm and 8cm audio disks. If you insert video CD, then the screen will display the status of the CD but it will not play the video file and therefore there will be no sound.

2. CD Indicator

This indicator light will be on if the CD is inside the CD DECK if the ignition switch of the auto- mobile is set to ACC (1st notch) or ON (2nd notch) regardless of whether the audio system is on or off. This light will go off when the CD is ejected.

3. CD Eject Button

Press [ ] button to eject the disk while playing the disk. This will eject the CD whether or not the ignition switch is on or off.

4. CD Selection Button

7. Automatic Previous Track Selection

FEATURES OF YOUR HYUNDAI

117

Press this button while the disk is inside the CD DECK to listen to the CD. If the radio was on previously then it will be turned off and CD player will be activated. If you press [CD] button when the disk is ejected and hanging in the opening the system will automatically insert the disk and play the CD.

5. Fast Backward (REW)

Press and hold [REW] button while playing CD then the player will play the disk backwards 5
times the regular speed for first 5 seconds and 15 times faster after that. The sound will be reduced by 12dB while you are holding the button.

6. Fast Forward (FF)

Press and hold [FF] button while playing CD then the player will play the disk forward 5 times the regular speed for first 5 seconds and 15
times faster after that. The sound will be re- duced by 12dB while you are holding the button.

Button

Press [ ] button to go to the beginning of the song you are listening to while playing the CD. Press the button again to go to the beginning of the song before the song you were listening to. When you press this button while listening to the first track of the CD then the system will move to the beginning of the last track of the CD.

8. Automatic Next Track Selection But-

ton

Press [ ] button to go to the beginning of the song next to the song you are listening to while playing the CD. When you press this button while listening to the last track of the CD then the system will move to the beginning of the first track of the CD.

9. Section Repeat Button (RPT)

Press [RPT] button to repeat the song you are listening to. Press this button again to cancel repetition.

10. Information Display Screen (LCD)

Various status of the CD will be displayed on the screen while listening to the CD such as "CD" while playing the CD, the track title and number and RPT.

1FEATURES OF YOUR HYUNDAI 118

11. SCAN Button If you press this button, the player will play 10
seconds of each track. Press it again to cancel scanning.

CAUTION:

o Do not insert warped or poor quality discs into the CD player as damage to the unit may occur.

o Do not insert anything like coins into the player slot as damage to the unit may occur.

o Do not place beverages close to the audio system. The playback mechanism may be damaged if you spill them.

o Do not strike or allow anything to impact the audio system, damage to the system mechanisms could occur.

o Off-road or rough surface driving may cause the compact disc to skip. Do not use the compact disc when driving in such conditions as damage to the com- pact disc face could occur.

o Do not attempt to grab or pull the com- pact disc out while the disc is being pulled into the audio unit by the self- loading mechanism. Damage to the audio unit and compact disc could oc- cur.

H465A01GK-GAT Stereo Radio Operation (H465) (If Installed)

1, 2

FEATURES OF YOUR HYUNDAI

119

1. 2. Power Button and Volume Control 3. Radio Band Selection Button 4. SCAN Button 5. Automatic Channel Selection Button 6. Manual Channel Selection Control (TUNE Control) 7. Preset Button 8. Information Display Screen (LCD) 9. AUDIO Select Button

GK_465_NA

1FEATURES OF YOUR HYUNDAI 120

H465B01GK-GAT 1. Power Button (POWER ON)

Press this button when the ignition switch of the automobile is set to ACC (1st notch) or ON (2nd notch) to turn on the power and the audio system. Press once again when the audio system is on to turn off the power.

2. Volume Control (VOLUME)

Turn the volume control clockwise to increase volume and counterclockwise to reduce. The volume level will be displayed on the screen when you adjust the volume.

3. Radio Band Selection Button (FM/AM)

o Press this button to listen to either FM or AM. o The radio will be set to each of the following

modes each time you press the button. FM1 ➟ FM2 ➟ AM

NOTE: Push this button when the power is off to turn on the power automatically.

4. SCAN Button

Press this button to automatically select chan- nels starting from the current channel and play each channel for 5 seconds. Press again to keep listening to the channel currently selected.

5. Automatic Channel Selection Button

(SEEK)

] button to automatically

Press the [SEEK increase frequency and press the [TRACK ] button to automatically decrease frequency to select and play the next available channel. If the received channel is memorized in the preset buttons then the screen will display the memo- rized channel.

6. Manual Channel Selection Control

(TUNE)

Turn the TUNE control clockwise to increase frequency and counterclockwise to reduce fre- quency by 1 step for each click.

7. Preset Button (1~6)

Press this button to listen to the channels memorized to each button. If you want to memo- rize the current channel to the preset button, press the button for more than 1.5 seconds then the channel will be memorized to the button with a beep.

8. Information Display Screen (LCD) A variety of information will be displayed on the screen including the radio bands (FM1/FM2/ AM) while listening to the radio, frequency of each channel, the number of preset channel and "ST" for FM stereo broadcasting.

9. AUDIO Select Button

Press this button to control tone. Each time you press the button, the mode will switch from BASS➟MIDDLE➟TREBLE➟FADER➟BALANCE and the mode will be displayed on the screen.

BASS

MIDDLE

TREBLE

Turn the TUNE Controller clockwise to increase bass tone and counterclockwise to decrease.

Turn the TUNE Controller clockwise to increase middle tone and counter- clockwise to decrease.

Turn the TUNE Controller clockwise to increase treble tone and counter- clockwise to decrease.

FEATURES OF YOUR HYUNDAI

121

BALANCE

FADER

Turn the TUNE Controller clockwise to increase right speaker volume and coun- terclockwise to increase left speaker volume.

Turn the TUNE Controller clockwise to increase rear speaker volume and coun- terclockwise to increase front speaker volume.

CAUTION:

o Do not place beverages close to the audio system. The audio system mecha- nism may be damaged if you spill them. o Do not strike or allow anything to impact the audio system, damage to the system mechanisms could occur.

1FEATURES OF YOUR HYUNDAI 122

H465C01GK-GAT Compact Disc Player Operation (H465) (If installed)

10

11

15

14

17

1. CD Deck 2. CD Load Button 3. CD Eject Button 4. Information Display Screen (LCD) 5. CD Changer Selection Button 6. Disc Selection Button 7. Fast Backward 8. Fast Forward