2003 Hyundai Tiburon Owners Manual

time. Information about the use of cruise control is beginning on page 1-44.

B270A01A-AAT BRAKE PAD WEAR WARNING SOUND The front disc brake pads have wear indicators that should make a high-pitched squealing or scraping noise when new pads are needed. The sound may come and go or be heard all the time when the vehicle is moving. It may also be heard when the brake pedal is pushed down firmly. Excessive rotor damage will result if the worn pads are not replaced. See your Hyundai dealer immediately.

B280A01A-AAT FUEL GAUGE

HGK133

The needle on the gauge indicates the approx- imate fuel level in the fuel tank. The fuel capac- ity is given in Section 9.

B290A02A-AAT ENGINE COOLANT TEMPERATURE GAUGE

HGK132

WARNING: Never remove the radiator cap when the engine is hot. The engine coolant is under pressure and could erupt and cause severe burns. Wait until the engine is cool before removing the radiator cap.

The needle on the engine coolant temperature gauge should stay in the normal range. If it moves across the dial to "H" (Hot), pull over and stop as soon as possible and turn off the engine. Then open the hood and check the coolant reservoir level and the water pump drive belt. If you suspect cooling system trou- ble, have your cooling system checked by a Hyundai dealer as soon as possible.

B300A01A-AAT SPEEDOMETER

FEATURES OF YOUR HYUNDAI

Your Hyundai's speedometer is calibrated in miles per hour (on the outer scale) and kilome- ters per hour (on the inner scale).

B330A01F-AAT TACHOMETER

B310B01GK-GAT ODOMETER/TRIP ODOMETER

A Type

B Type

HGK131

The tachometer registers the speed of your engine in revolutions per minute (rpm). It is useful to help you shift at the appropriate engine speed to avoid lugging or over-reving the en- gine.

CAUTION: The engine should not be raced to such a speed that the needle enters the red zone on the tachometer face. This can cause severe engine damage and may void your warranty.

HGK028B

Function of digital odometer/trip odometer Pushing in the reset switch on the right side of speedometer when the ignition switch is turned "ON" will display the following sequence:

A Type

HGK130B

HGK055A

1- 29

B Type

HGK055C

1. Odometer The odometer records the total driving distance in kilometers or miles, and is useful for keeping a record for maintenance intervals.

NOTE: Any alteration of the odometer may void your warranty coverage.

2,3 Trip odometer Records the distance of 2 trips in kilometers or miles. TRIP A: First distance you have traveled from your origination point to a first destination. TRIP B: Second distance from the first destina- tion to the final destination.

To shift from TRIP A to TRIP B, press the reset switch. When pressed for 1 second, it will reset to 0.

1- 30

FEATURES OF YOUR HYUNDAI

B340A01A-AAT COMBINATION TURN SIGNAL, HEADLIGHT AND HIGH-BEAM SWITCH Turn Signal Operation Pulling down on the lever causes the turn signals on the left side of the car to blink. Pushing upwards on the lever causes the turn signals on the right side of the car to blink. As the turn is completed, the lever will automati- cally return to the center position and turn off the turn signals at the same time. If either turn signal indicator light blinks more rapidly than usual, goes on but does not blink, or does not go on at all, there is a malfunction in the system. Check for a burned-out fuse or bulb or see your Hyundai dealer.

B340B01A-AAT Lane Change Signal

HGK038

To indicate a lane change, move the lever up or down to a point where it begins flashing. The lever will automatically return to the center position when released.

B340C02E-AAT Headlight Switch

HGK039

To operate the headlights, turn the barrel on the end of the multi-function switch. The first posi- tion turns on the parking lights, sidelights, tail lights and instrument panel lights. The second position turns on the headlights.

Parking light auto cut If you do not turn the parking lights "OFF" after driving, the parking light will automatically shut "OFF" when the driver's door is opened. To turn them "ON" again you must simply turn the ignition key to the "ON" position.

B340D01A-AAT High-beam Switch To turn on the headlight high beams, push the lever forward (away from you). The high beam indicator light will come on at the same time. For low beams, pull the lever back toward you.

B340F01L-GAT Auto Light (If installed)

HGK041

To operate the auto light, turn the barrel on the end of the multi-function switch. If you set the multi-function switch to "AUTO", the tail lights and headlights will be turned automatically on or off according to external illumination.

FEATURES OF YOUR HYUNDAI

B340E01A-AAT Headlight Flasher

B350A01GK-AAT WINDSHIELD WIPER AND WASHER SWITCH

HGK233

To flash the headlights, pull the switch lever toward you, then release it. The headlights can be flashed even though the headlight switch is in the "OFF" position.

(1)

(2)

(3)

HGK042

The windshield wiper switch has three posi- tions:

(1) Intermittent wiper operation (2) Low-speed operation (3) High-speed operation

NOTE: To prevent damage to the wiper system, do not attempt to wipe away heavy accumula- tions of snow or ice. Accumulated snow and ice should be removed manually. If there is only a light layer of snow or ice, operate the heater in the defrost mode to melt the snow or ice before using the wiper.

1- 31

Mist Wiper Operation

FEATURES OF YOUR HYUNDAI

To use the intermittent wiper feature, place the wiper switch in the "INT" position. With the switch in this position, the interval between wipes can be varied from 2 to 10 seconds by turning the interval adjuster barrel.

o In icy or freezing weather, be sure the wiper blades are not frozen to the glass prior to operating the wipers.

o In areas where water freezes in winter,

use windshield washer antifreeze.

B350B01A-AAT Windshield Washer Operation

B350A01O-AAT Tailgate Wiper And Washer Switch

If a single wipe is desired in mist, move the windshield wiper and washer control lever up.

HGK045

B350C01S-AAT Adjustable Intermittent Wiper Opera- tion

1- 32

HGK043

HGK044

HGK046

To use the windshield washer, pull the wiper/ washer lever toward the steering wheel. When the washer lever is operated, the wipers auto- matically make two passes across the wind- shield. The washer continues to operate until the lever is released.

NOTE: o Do not operate the washer more than 15
seconds at a time or when the fluid res- ervoir is empty.

1.

:The washer fluid will be sprayed onto the rear window and the wiper operates while the rear window wiper barrel is placed in this position.

2.OFF 3.INT :To use the intermittent wiper feature, place the rear window wiper barrel in the "INT" position.

4.ON :When the point indicates the "ON", the rear window wiper operates continu- ously.

B370A01A-AAT HAZARD WARNING SYSTEM

B380A01A-AAT REAR WINDOW DEFROSTER SWITCH

B400A01F-AAT DIGITAL CLOCK

FEATURES OF YOUR HYUNDAI

A Type

B Type

HGK140A

B380A01GK

HGK143A

The hazard warning system should be used whenever you find it necessary to stop the car in a hazardous location. When you must make such an emergency stop, always pull off the road as far as possible. The hazard warning lights are turned on by pushing in on the hazard switch. This causes all turn signal lights to blink. The hazard warning lights will operate even though the key is not in the ignition. To turn the hazard warning lights off, push in on the switch a second time.

The rear window defroster is turned on by pushing in on the switch. To turn the defroster off, push in on the switch a second time. The rear window defroster automatically turns itself off after about 15 minutes. To restart the de- froster cycle, push in on the switch again after it has turned itself off.

CAUTION: Do not clean the inner side of the rear window glass with an abrasive type of glass cleaner or use a scraper to remove foreign deposits from the inner surface of the glass as this may cause damage to the defroster elements.

NOTE: The engine must be running for the rear window defroster to operate.

There are three control buttons for the digital clock. Their functions are:

HOUR - Push "H" to advance the hour indicat-

ed.

MIN - Push "M" to advance the minute indicat-

ed.

RESET - Push "R" to reset minutes to ":00" to facilitate resetting the clock to the correct time. When this is done:

Pressing "R" between 10 : 30 and 11 : 29
changes the readout to 11 : 00. Pressing "R" between 11 : 30 and 12 : 29
changes the readout to 12 : 00.

1- 33

B410A01A-AAT INSTRUMENT PANEL LIGHT CON- TROL (RHEOSTAT)

HGK134A

The instrument panel lights can be made bright- er or dimmer by turning the instrument panel light control knob.

B420A02A-AAT CIGARETTE LIGHTER

FEATURES OF YOUR HYUNDAI

For the cigarette lighter to work, the key must be in the "ACC" position or the "ON" position. To use the cigarette lighter, push it all the way into its socket. When the element has heated, the lighter will pop out to the "ready" position. Do not hold the cigarette lighter pressed in. This can damage the heating element and create a fire hazard. If it is necessary to replace the cigarette lighter, use only a genuine Hyundai replacement or its approved equivalent.

CAUTION: Do not use electric accessories or equipment other than the Hyundai genuine parts in the socket.

B430A01GK-AAT FRONT ASHTRAY

HGK144

The front ashtray may be opened by pushing and releasing the ashtray door at its top edge.

HGK146

1- 34

To remove the ashtray in order to clean it, the metal ash receptacle should be lifted out from the ashtray door. Do not attempt to remove the entire ashtray door assembly or damage will result. To reinstall it, place it in the proper position and press it down in the ashtray door. The ashtray lamp will only illuminate when the exterior body lights are switched on.

B450A01GK-AAT DRINK HOLDER (If Installed)

HGK149A

The drink holder is used for holding cups or cans.

WARNING: Do not place objects other than cups or cans in the drink holder. Such objects can be thrown out in the event of a sudden stop or an accident, possibly injuring the passengers in the vehicle.

B460A01Y-AAT SUNROOF (If installed) Sun Shade

FEATURES OF YOUR HYUNDAI

B460B01GK-GAT Opening the Sunroof System

HGK029

Your HYUNDAI is equipped with a sliding sun- shade which you can manually adjust to let in light with the sunroof closed, or to block sun- light.

WARNING: Never adjust the sunshade while driving.

HGK030

The sunroof can be electrically opened or closed with the ignition key in the "ON" position. The sunroof is moved to its fully open position by pushing the "OPEN" switch, and to stop at the desired position, push in any switches (Open, Close, Up, Down). To close, press and hold the "CLOSE" button. Release the button when the sunroof reaches the desired position.

WARNING: o Do not close a sunroof if anyone’s hands, arms or body are between the sliding glass and the sunroof sash, as this could result in injury.

o Do not place your head or arms out of

the sunroof opening at any time.

CAUTION: o Do not open the sunroof in severely cold temperature or when it is covered with ice or snow.

o Periodically remove any dirt that may

have accumulated on the guide rails.

B460C01GK-GAT Tilting the Sunroof System

HGK031

The sunroof is moved to its fully tilt up position by pushing the "UP" switch, and to stop at the desired position, push in any switches (Open, Close, Up, Down). To tilt down, press and hold the "DOWN" but- ton. Release the button when the sunroof reaches the desired position.

NOTE: After washing the car or after there is rain, be sure to wipe off any water that is on the sunroof before operating it.

1- 35

FEATURES OF YOUR HYUNDAI

3. Turn the wrench clockwise to open or coun-

(1) Push in the map light switch to turn on the

terclockwise to close the sunroof.

driver side light.

B460D01GK-AAT Manual Operation of Sunroof If the sunroof does not electrically operate:

1. Remove the cap located in the rear roof

panel by using a coin or screw driver.

HGK032

B460E01TB-GAT Resetting the Sunroof System If the battery has been recharged, disconnected or is manually with operating the hexagonal head wrench, you may need to reset the sunroof.

To do this; 1. Turn the ignition switch "OFF". 2. With pressing "OPEN" "UP" button at the

3.

same time, turn the ignition switch "ON". If the sunroof is set like this, the sunroof is reset with tilting up/down automatically once for all.

CAUTION: If the sunroof is not reset, it may not be operated normally.

B480A01GK-GAT MAP LIGHT

HGK033

2.

Insert the hexagonal head wrench provided with the vehicle into the socket. This wrench can be found in the vehicle’s trunk or glove box.

1- 36

(1)

(2)

(3)

HGK034

(2) In the "DOOR" position, the interior courte- sy light comes on when any door is opened regardless of the ignition key position. The light goes out gradually 6 seconds after the door is closed.

(3) Push in the map light switch to turn on the

passenger side light.

B491A02F-AAT SPECTACLE CASE

HGK036

The spectacle case is located on the front overhead console. Push the end of the cover to open or close the spectacle case.

WARNING: Do not open the spectacle case while the vehicle is moving. The rear view mirror of the vehicle can be blocked by an open spectacle case.

B500A01A-AAT GLOVE BOX

FEATURES OF YOUR HYUNDAI

B510B01A-AAT OUTSIDE REAR VIEW MIRROR Electric Type (If installed)

HGK147

WARNING: To avoid the possibility of injury in case of an accident or a sudden stop, the glove box door should be kept closed when the car is in motion.

o To open the glove box, pull on the glove box

release lever.

HGK128

The outside rearview mirrors can be adjusted to your preferred rear vision, both directly behind the vehicle, and to the rear of the left and right sides. The remote control outside rearview mirror switch controls the adjustments for both the right and left outside mirror.

To adjust the position of either mirror: 1. Move the selecting switch to the right or left to activate the adjustable mechanism for the corresponding door mirror.

2. Next, adjust the mirror angle by depressing the appropriate perimeter switch as illus- trated.

CAUTION: o Do not operate the switch continuously

for an unnecessary length of time.

o Scraping ice from the mirror face could cause permanent damage. To remove any ice, use a sponge, soft cloth or approved deicer.

WARNING: Be careful when judging the size or distance of any object seen in the passenger side rear view mirror. It is a convex mirror with a curved surface. Any objects seen in this mirror are closer than they appear.

B510D01Y-AAT OUTSIDE REARVIEW MIRROR HEATER (If Installed)

A Type

B Type

B380A01GK

1- 37

The outside rearview mirror heater is actuated in connection with the rear window defroster. To heat the outside rearview mirror glass, push in the switch for the rear window defroster. The rearview mirror glass will be heated for defrost- ing or defogging and will give you improved rear vision in inclement weather conditions. Push the switch again to turn the heater off. The outside rearview mirror heater automatically turns itself off after 15 minutes.

B510C01A-AAT FOLDING THE OUTSIDE REAR VIEW MIRRORS

FEATURES OF YOUR HYUNDAI

WARNING: Do not adjust or fold the outside rear view mirrors while the vehicle is moving. This could result in loss of control, and an acci- dent which could cause death, serious inju- ry or property damage.

B520A01A-AAT DAY/NIGHT INSIDE REAR VIEW MIR- ROR

B520B01O-GAT DAY/NIGHT REAR VIEW MIRROR (Electric type) (If installed)

Sensor

B520B01GK

The electric type day/night inside rearview mir- ror automatically controls the glare of head- lights of the car behind you. Adjust the rearview mirror to the desired position.

B520A01GK

Your Hyundai is equipped with a day/night inside rear view mirror. The "night" position is selected by flipping the tab at the bottom of the mirror toward you. In the "night" position, the glare of headlights of cars behind you is re- duced.

B510C01GK To fold the outside rear view mirrors, push them toward the rear. The outside rear view mirrors can be folded rearward for parking in narrow areas.

1- 38

FEATURES OF YOUR HYUNDAI

B530A01A-AAT PARKING BRAKE

B360A01F-AAT FRONT FOG LIGHT SWITCH (If Installed)

B550A01S-GAT HIGH-MOUNTED REAR STOP LIGHT

A Type

B Type

C Type

To turn on the front fog lights, push the switch. They will light when the headlights are turned on.

HGK142A

B550A01GK

In addition to the lower-mounted rear stoplights on either side of the car, the high mounted rear stoplight in the center of the rear window or inserted in the rear spoiler also lights when the brakes are applied.

HGK178

Always engage the parking brake before leav- ing the car. This also turns on the parking brake indicator light when the key is in the "ON" or "START" position. Before driving away, be sure that the parking brake is fully released and the indicator light is off. o To engage the parking brake, pull the lever

up as far as possible.

o To release the parking brake, pull up the lever and press the thumb button. Then, while holding the button in, lower the brake lever.

1- 39

B620A01S-AAT FRONT DOOR EDGE WARNING LIGHT

B570A01GK-GAT HOOD RELEASE

FEATURES OF YOUR HYUNDAI

B620A01GK

Hood Release Lever

HGK106

A red light comes on when the front door is opened. The purpose of this light is to assist when you get in or out and also to warn passing vehicles.

1. Pull the release knob to unlatch the hood. 2. Press the safety hook lever up and lift the

hood.

3. Raise the hood by hand.

When closing the hood, slowly close the hood and make sure it locks into place.

1- 40

HGK098

WARNING: o Always double check to be sure that the hood is firmly latched before driving away. If it is not latched, the hood could fly open while the vehicle is being driven, causing a total loss of visibility, which might result in an accident.

o Do not move the vehicle with the hood in the raised position, as vision is obstructed and the hood could fall or be damaged.

B560A02S-AAT REMOTE FUEL-FILLER LID RELEASE

HGK105

The fuel-filler lid may be opened from inside the vehicle by pulling up on the fuel-filler lid opener located on the front floor area on the left side of the car.

NOTE: If the fuel-filler lid will not open because ice has formed around it, tap lightly or push on the lid to break the ice and release the lid. Do not pry on the lid. If necessary, spray around the lid with an approved deicer fluid (do not use radiator anti-freeze) or move the vehicle to a warm place and allow the ice to melt.

HGK124

WARNING: o The fuel cap must be tightened at least 3
clicks, otherwise " " light will illumi- nate.

o Gasoline vapors are dangerous. Before refueling, always stop the engine and never allow sparks or open flames near the filler area. If you need to replace the filler cap, use a genuine Hyundai replace- ment part.

FEATURES OF YOUR HYUNDAI

o If you open the fuel filler cap during high ambient temperatures, a slight "pressure sound" may be heard. This is normal and not a cause for concern. Whenever you open the fuel filler cap, turn it slowly.

o Make sure the fuel filler cap is replaced and securely seated after fueling. Failure to replace or fully seat the fuel filler cap will result in fuel vapors escaping into the atmosphere and the MIL indicator illuminating.

o Do not "TOP-OFF" after the first nozzle

shut off when refueling.

To open the tail gate without using the key, pull up the lid release lever. To close, lower the tail gate, then press down on it until it locks. To be sure the tail gate is securely fastened, always try to pull it up again.

WARNING: The tail gate should always be kept com- pletely closed while the vehicle is in motion. If it is left open or ajar, poisonous exhaust gases may enter the car resulting in serious illness or death to the occupants. See addi- tional warnings concerning exhaust gases on page 2-1.

B540A01F-AAT TAIL GATE Remote Tail Gate Release

B540C01F-AAT To Unlock Using the Key

HGK103

B540C02GK

To open the tail gate, insert the key and turn it clockwise to unlock. The tail gate compartment light illuminates when the tail gate is opened. 1- 41

B540D01GK-GAT When you close the tailgate

B140A01S-AAT REAR SEAT WARNING

B580A01GK-AAT SUN VISOR

FEATURES OF YOUR HYUNDAI

HGK226

B140A01GK

For the safety of all passengers, luggage or other cargo should not be piled higher than the top of the seatback. In addition, do not place objects on the rear shelf as they may move forward during braking or in an accident and strike vehicle passengers.

HGK227

WARNING: Do not close an open tailgate (rear hatch) while a person(s) is sitting upright on the rear seat. The tailgate or tailgate glass may contact the head of a person sitting upright on the rear seat. Closing the tailgate onto a person's head may cause serious injuries, including death. 1- 42

Vanity mirror

HGK145

Your Hyundai is equipped with sun visors to give the driver and front passenger either fron- tal or sideward shade. The sun visors are fitted on both sides on all models. To reduce glare or to shut out direct rays of the sun, turn the sun visor down to block the annoyance. A vanity mirror is provided on the back of the sun visor for the front passenger.

NOTE: The Supplemental Restraint System (SRS) label containing useful information can be found on the back of each sun visor.

WARNING: Do not place the sun visor in such a manner that it obscures visibility of the roadway, traffic or other objects.

FEATURES OF YOUR HYUNDAI

B600A01HP-AAT STEERING WHEEL TILT LEVER (If installed) To adjust the steering wheel:

B610A01S-AAT HORN

Working Zone

Some objects can be kept in the net in the luggage compartment. Use the luggage net on the floor(If installed) or at the back of the luggage compartment to prevent objects from sliding.

B990A03Y-AAT FLOOR MAT ANCHOR

HGK127

Press the pad on the steering wheel to sound the horn.

HGK141

1. Pull the lever toward you and hold it to

unlock.

2. Raise or lower the steering wheel to the

desired position.

3. After adjustment, release the lever.

WARNING: Do not attempt to adjust the steering wheel while driving as this may result in loss of control of the vehicle and serious injury or death.

B540D01GK-GAT LUGGAGE NET (If installed)

A Type

HGK129

To use a floor mat on the front floor carpet, make sure it attaches to the floor mat anchor in your vehicle. This keeps the floor mat from sliding forward.

WARNING: o Make sure the floor mat is properly placed on the floor carpet. If the floor mat slips and interferes with the movement of the pedals during driving, it may cause an accident.

B Type

HGK241

1- 43

o Don't put an additional floor mat on the top of the anchored mat, otherwise the additional mat may slide forward and interfere with the movement of the ped- als.

B660A01S-AAT CRUISE CONTROL (If Installed)

Main switch

B660A01GK

The cruise control system provides automatic speed control for your comfort when driving on freeways, tollroads, or other noncongested high- ways. This system is designed to function above approximately 25 mph (40 km/h).

1- 44

FEATURES OF YOUR HYUNDAI

B660B01E-AAT To Set the Cruise Speed

WARNING: To avoid accidental cruise control engage- ment, keep the cruise control main switch off when not using the cruise control

B660C02E-AAT To Cancel the Cruise Speed

B660B01GK

1. Push in the cruise control main switch on the end of the barrel. The "CRUISE" indica- tor light in the instrument cluster will be illuminated. This turns the system on.

2. Accelerate to the desired cruising speed

above 25 mph (40 km/h).

3. Push the control switch downward to "SET

(COAST)" and release it.

4. Remove your foot from the accelerator pedal and the desired speed will automatically be maintained.

5. To increase speed, depress the accelerator pedal enough for the vehicle to exceed the preset speed. When you remove your foot from the accelerator pedal, the vehicle will return to the speed you have set.

B660C01GK

Do one of the following: o Pull the control switch toward the steering

wheel to "CANCEL" position.

o Depress the brake pedal. o Depress the clutch pedal (Manual transaxle). o Shift the selector lever to "N" position (Auto-

matic transaxle).

o Decrease the vehicle speed lower than the

memorized speed by 12 mph (20 km/h).

o Decrease the vehicle speed to less than 25

mph (40 km/h).

o Release the main switch.

B660D01E-AAT To Resume the Preset Speed

B660F01E-AAT To Reset at a Slower Speed

FEATURES OF YOUR HYUNDAI

B660D01GK

The vehicle will automatically resume the speed set prior to cancellation when you push the control switch upward to "RESUME (ACCEL)" position and release it, providing the vehicle speed is above 25 mph (40 km/h).

B660E01E-AAT To Reset at a Faster Speed 1. Push the control switch upward to "RE-

SUME (ACCEL)" position and hold it.

2. Accelerate to desired speed and release the control switch. While the control switch is held, the vehicle will gradually gain speed.

B660B01GK 1. Push the control switch downward to "SET (COAST)" and hold it. The vehicle will de- celerate.

2. When the desired speed is obtained, re- lease the control switch. While the control switch is pushed, the vehicle speed will gradually decrease.

WARNING: o Keep the main switch off when not using

the cruise control.

o Do not use the cruise control when it may not be safe to keep the car at a constant speed, for instance, driving in heavy or varying traffic, or on slippery (rainy, icy or snow-covered) or winding roads or over 6% up-hill or down-hill roads.

o Pay particular attention to the driving con- ditions whenever using the cruise control system.

o During cruise-control driving with a manual transaxle vehicle, do not shift into neutral without depressing the clutch pedal, or the engine will be overrevved. If this happens, depress the clutch pedal or release the main switch.

o With the cruise control engaged, when the brake pedal is applied, it is normal to hear the cruise control system deactivate. This is an indication of normal system operation.

o During normal cruise control operation, when the "SET(COAST)" is activated or reactivated after applying the brakes, the cruise control will energize after approxi- mately 3 seconds. This delay is normal.

1- 45

FEATURES OF YOUR HYUNDAI

B710A01GK-GAT HEATING AND COOLING CONTROL

1. Side defrost nozzle 2. Side Ventilator 3. Center Ventilator 4. Windshield Defrost Ventilator

1- 46

HGK001B

B710A01S-AAT VENTILATION To operate the ventilation system:

o Set the air intake control to "Fresh" mode

( ).

o To direct all intake air to the dashboard

vents, set the airflow control to “Face”.

o Adjust the fan speed control to the desired

speed.

o Set the temperature control between “Cool”

and “Warm”.

B710B01S-AAT CENTER VENTILATOR The center ventilators are located in the middle of the dashboard. The direction of air flow from the vents in the center of the dashboard is adjustable. To control the direction of the air flow, move the knob in the center of the vent up-and-down and side-to-side.

B710C01S-AAT SIDE VENTILATOR The side ventilators are located on each side of the dashboard. To change the direction of the air flow, move the knob in the center of the vent up-and-down and side-to-side. The side vent knobs control the amount of outside air entering the vehicle through the side vents. The vents are opened when the vent knob is moved to the up position. The vents are closed when the vent knob is moved to the down position. Keep these vents clear of leaves and other debris.

FEATURES OF YOUR HYUNDAI

B670A01GK-GAT ROTARY TYPE

B670B01A-AAT Fan Speed Control (Blower Control)

B670E01A-AAT Temperature Control

HGK002

HGK006

Cool

Warm

HGK007

1. Air Conditioning switch 2. Air intake control switch 3. Rear window defroster switch 4. Air flow control switch 5. Fan speed control switch 6. Temperature control switch

This is used to turn the blower fan on or off and to select the fan speed. This blower fan speed, and therefore the vol- ume of air delivered from the system, may be controlled manually by setting the blower con- trol between the "1" and "4" positions.

This is used to turn the heating system on and off and to select the degree of heating desired.

1- 47

FEATURES OF YOUR HYUNDAI

With the "Recirculation" mode selected, air from within the passenger compartment will be drawn through the heating system and heated or cooled according to the function selected.

NOTE: o It should be noted that prolonged opera- tion of the heating in "Recirculation" mode will give rise to fogging of the windshield and side windows and the air within the passenger compartment will become stale. In addition, prolonged use of the air conditioning with the "Recircu- lation" mode selected may result in the air within the passenger compartment becoming excessively dry.

o When the ignition switch is turned "ON" the air intake control will change to "Re- circulation" mode (regardless of switch position). This is normal operation.

B670D02GK-AAT Air Flow Control

HGK005

This is used to direct the flow of air. Air can be directed to the floor, dashboard outlets, or wind- shield. Five symbols are used to represent Face, Bi-Level, Floor, Floor-Defrost and De- frost air position.

B670C02S-AAT Air Intake Control

HGK016

This is used to select fresh outside air or recirculation inside air. To change the air intake control mode, (Fresh mode, Recirculation mode) push the control button.

FRESH MODE ( ) : The indicator light on the button goes off when the air intake control is fresh mode.

RECIRCULATION MODE ( ): The indicator light on the button is illuminated when the air intake control is recirculation mode.

With the "Fresh" mode selected, air enters the vehicle from the outside and is heated or cooled according to the function selected.

1- 48

FEATURES OF YOUR HYUNDAI

If the "Floor-Defrost" mode is selected, the A/C will be turn on automatically and "Fresh" mode will be activated.

HGK021

HGK023

Face-Level

Selecting the "Face" mode will cause air to be discharged through the face level vents.

Floor-Level

Air is discharged through the floor vents, wind- shield defroster nozzle, side defroster nozzle, side ventilator.

HGK025

Defrost-Level

Air is discharged through the windshield defrost nozzle, side defroster nozzle, side ventilator. If the "Defrost" mode is selected, the A/C will turn on automatically and "Fresh" mode will be activated.

Bi-Level

HGK022

HGK024

Air is discharged through the face vents and the floor vents. This makes it possible to have cooler air from the dashboard vents and warmer air from the floor outlets at the same time.

Floor-Defrost Level

Air is discharged through the windshield defrost nozzle, the floor vents, side defroster nozzle, side ventilator.

1- 49

FEATURES OF YOUR HYUNDAI

B740A01S-AAT AIR CONDITIONING SYSTEM Air Conditioning Switch (If installed)

B740B01S-AAT Air Conditioning Operation Cooling

B690A02S-AAT HEATING CONTROLS For normal heating operation, set the air intake control to the "Fresh" position and the air flow control to "Floor".

For faster heating, the air intake control should be in the "Recirculation" position.

If the windows fog up, move the air flow control to the "Def" (defroster) position. (The A/C will turn on automatically and "Fresh" mode will be activated.)

HGK002

For maximum heat, move the temperature con- trol to “Warm”.

The air conditioning is turned on or off by pushing the A/C button on the heating/air con- ditioning control panel.

HGK018

1- 50

To use the air conditioning to cool the interior: o Set the side vent control to "OFF", to shut off

outside air entry.

o Turn on the fan control switch. o Turn on the air conditioning switch by push- ing in on the switch. The air conditioning indicator light should come on at the same time.

o Set the air intake control to "Fresh" mode

( ).

o Set the temperature control to "Cool". ("Cool" provides maximum cooling. The tempera- ture may be moderated by moving the con- trol toward "Warm".)

o Adjust the fan control to the desired speed. For greater cooling, turn the fan control to one of the higher speeds or temporarily select the "Recirculation" position on the air intake control.

B740C01S-AAT Dehumidified Heating For dehumidified heating:

o Turn on the fan control switch. o Turn on the air conditioning switch. The air conditioning indicator light should come on at the same time.

o Set the air intake control to "Fresh" mode

( ).

o Set the air flow control to "Face". o Adjust the fan control to the desired speed. o For more rapid action, set the fan at one of

the higher speeds.

o Adjust the temperature control to provide the

desired amount of warmth.

FEATURES OF YOUR HYUNDAI

B720A02FC-GAT

DEFROSTING/DEFOGGING

A Type

B Type

A Type

B Type

B720A01GK

B720A02GK

Use the heating/ventilation system to defrost or defog the windshield:

To remove interior fog on the windshield: o Set the air flow control to the defrost (

) position. (The A/C will turn on automatically and "Fresh" mode will be activated)

To remove frost or exterior fog on the windshield: o Set the air flow control to the defrost ( ) position. (The A/C will turn on automatically and "Fresh" mode will be activated.)

o Set the temperature control to warm. o Set the fan speed control to position "3" or "4".

o Set the temperature control to the desired position. o Set the fan speed control between "1" and "4" position. NOTE: ), it may cause When the A/C is operated continuously on the floor-defrost level ( fog to form on the exterior windshield. If this occurs, set the air flow control to the face level position ( ) and fan speed control to the low position.

) or defrost level (

1- 51

FEATURES OF YOUR HYUNDAI

B730A01FC-GAT OPERATION TIPS o To keep dust or unpleasant fumes from entering the car through the ventilation sys- tem, temporarily set the air intake control to "Recirculation". Be sure to return the control to "Fresh" when the irritation has passed to keep fresh air in the vehicle. This will help keep the driver alert and comfortable.

o Air for the heating/cooling system is drawn in through the grilles just ahead of the wind- shield. Care should be taken that these are not blocked by leaves, snow, ice or other obstructions.

o To prevent interior fog on the windshield, set the air intake control to the fresh air ( ) position and fan speed to the desired posi- tion.

1- 52

FEATURES OF YOUR HYUNDAI

B970A01Y-AAT AUTOMATIC HEATING AND COOLING CONTROL SYSTEM (If lnstalled) Your Hyundai is equipped with an automatic heating and cooling control system controlled by simply setting the desired temperature.

B970B01GK-GAT Heating and Cooling Controls TYPE A (Without Air Quality System)

TYPE B (With Air Quality System)

2 3

3 4

10

11

10

12

11

HGK003

HGK004

1. Temperature Control Button 2. Defroster Switch 3. Display Window 4. Air Conditioning Switch 5. Rear Window Defroster Switch

6. Fan Speed Control Switch 7. Air Flow Control Switch 8. AUTO (Automatic Control)Switch 9. OFF Switch 10. Air lntake Control Switch 11. Ambient Switch 12. Air Quality System Switch (If installed)

1- 53

B970C02E-AAT Automatic Operation

FEATURES OF YOUR HYUNDAI

HGK020

The FATC (Full Automatic Temperature Con- trol) system automatically controls heating and cooling as follows:

1. Push the "AUTO" switch. The indicator light will illuminate confirming that the Face, Floor and/or Bi-Level modes as well as the blower speed and, air conditioner will be controlled automatically.

HGK014
2. Push the "TEMP" button to set the desired

temperature. The temperature will increase to the maxi- mum 90°F(32°C) by pushing on the button. Each push of the button will cause the temperature to increase by 1°F(0.5°C). The temperature will decrease to the mini- mum 62°F(17°C) by pushing on the button. Each push of the button will cause the temperature to decrease by 1°F(0.5°C).

1- 54

NOTE: If the battery has been discharged or discon- nected, the temperature mode will reset to centigrade degrees. This is a normal condition and you can change the temperature mode from centigrade to farenheit as follows; Press the TEMP button down 3 seconds or more with the button held down. The display shows that the unit of temperature is adjusted to centigrade or fahrenheit. (°C °F or °F °C)

OUTSIDE

TEMP

Photo sensor

G280A01GK

NOTE: Never place anything over the sensor which is located on the instrument panel to ensure better control of the heating and cooling system.

FEATURES OF YOUR HYUNDAI

B995A01Y-GAT AMBIENT SWITCH

B980B01Y-AAT Fan Speed Control Switch

B670C01GK-AAT Air Intake Control Switch (Without A.Q.S)

HGK009

HGK015

Pressing the button displays the ambient temperature on the LCD.

OUTSIDE

TEMP

B980A01Y-AAT MANUAL OPERATION The heating and cooling system can be con- trolled manually as well by pushing buttons other than the "AUTO" button. In this state, the system sequentially works according to the order of buttons selected. The function of the buttons which are not se- lected will be controlled automatically. Press the "AUTO" button in order to convert to automatic control of the system.

The fan speed can be set to the desired speed by pressing the appropriate fan speed control button. The higher the fan speed is, the more air is delivered. Pressing the "OFF" button turns off the fan.

HGK008

This is used to select fresh outside air or recirculation inside air. To change the air intake control mode, (Fresh mode, Recirculation mode) push the control button.

FRESH MODE ( ) : The indicator light on the button goes on when the air intake control is fresh mode.

RECIRCULATION MODE ( ) : The indica- tor light on the button is illuminated when the air intake control is recirculation mode.

With the "Fresh" mode selected, air enters the vehicle from the outside and is heated or cooled according to the function selected.

1- 55

With the "Recirculation" mode selected, air from within the passenger compartment will be drawn through the heating system and heated or cooled according to the function selected.

NOTE: o It should be noted that prolonged opera- tion of the heating system in "recircula- tion" mode will give rise to fogging of the windshield and side windows and the air within the passenger compartment will become stale. In addition, prolonged use of the air conditioning with the "Recircu- lation" mode selected may result in the air within the passenger compartment becoming excessively dry.

o When the ignition switch is turned "ON" the air intake control will change to " mode (regardless of switch position). This is normal operation. The air intake con- trol operates in "AUTO" mode when turn- ing the ignition to the ON position if the "AUTO" mode was used before shutting off the engine.

1- 56

FEATURES OF YOUR HYUNDAI

B980C01GK-GAT Air Intake Control Switch (With A.Q.S) (If Installed)

This is used to select fresh outside air or recirculate inside air automatically.

HGK010

: OFF : ON

Fresh mode :

Air enters the vehicle from the outside and is heated or cooled according to the function se- lected.

Recirculation mode :

Air from within the passenger compartment will be drawn through the heating system and heated or cooled according to the function selected.

Exhaust gas cutoff mode :

Air enters the vehicle from the outside. But if exhaust gas enters the vehicle from the outside, the exhaust gas cutoff mode ( ) is automatically converted to the mode, to prevent exhaust gas from entering the vehicle.

NOTE: o It should be noted that prolonged opera- tion of the heating system in recircula- tion mode ( ) will give rise to misting of the windshield and side windows and the air within the passenger compart- ment will become stale. In addition, pro- longed use of the air conditioning with the recirculation mode ( ) selected may result in the air within the passenger compartment becoming excessively dry. o When the ignition switch is turned "ON" the air intake control will change to "Fresh" mode (regardless of switch posi- tion). This is normal operation. The air intake control is operated in "AUTO" mode when turning the ignition to the ON position if the "AUTO" mode was used before shutting off the engine.

CAUTION: If the windows fog up with the Recirculation or A.Q.S mode selected, set the air intake control to the Fresh air position or A.Q.S control to "OFF".

B980D01Y-AAT Heating and Cooling System Off Press the "OFF" button to stop the operation of the heating and cooling system.

B980E01GK-GAT Air Flow Control

HGK019

This is used to direct the flow of air. Air can be directed to the floor, dashboard outlets, or wind- shield. Four symbols are used to represent Face, Bi-Level, Floor and Floor-Defrost air position.

FEATURES OF YOUR HYUNDAI

vents. This makes it possible to have cooler air from the dashboard vents and warmer air from the floor outlets at the same time.

HGK021

Face-Level

When selecting the "Face" mode, the indicator light will come on, causing air to be discharged through the face level vents.

HGK023

Floor-Level

When selecting the "Floor-Level" mode, the indicator light will come on and the air will be discharged through the floor vents, windshield defroster nozzle, side defroster nozzle, side ventilator.

HGK022

Bi-Level

When selecting the "Bi-Level" mode, the indica- tor light will come on and the air will be dis- charged through the face vents and the floor

HGK024
1- 57

CAUTION: o Replace the filter every 12,000 miles (20,000 km) or once a year. If the car is being driven in severe conditions such as dusty, rough roads, more frequent air filter inspections and changes are re- quired.

o When the air flow rate is suddenly de- creased, it must be checked at an autho- rized dealer.

o If your vehicle is not equipped with this filter, it can be installed by your dealer. Check with your dealer for details.

FEATURES OF YOUR HYUNDAI

Floor-Defrost Level

When selecting the "Floor-Defrost" mode, the indicator light will come on and the air will be discharged through the windshield defrost nozzle, the floor vents, side defroster nozzle, side ventilator.

B760A02GK-AAT AIR FILTER (IN FRONT OF BLOWER UNIT) (If Installed)

Outside air

Inside air

Filter

B980F02E-AAT Defrost Switch

Blower fan

Evaporator core

Inside air

Heater core

B760A01E

The air filter is located in front of the blower uniit behind the glove box. It operates to decrease pollutants from entering the car and to filter the air.

Replacement instructions: 1. Open the glove box and remove the taping screws on the upper side of the glove box. 2. Remove the taping screws on the lower

position of the glove box.

3. Remove the filter cover and replace the

4.

filter. Installation is the reverse order of disassem- bly.

HGK012

When the "Defrost" button is pressed, the " " mode will be automatically selected and the air will be discharged through the windshield de- frost vents. To assist in defrosting, the air conditioning will operate if ambient temperature is higher than 38.3 °F (3.5 °C) and automatically turns off if the ambient temperature drops below 38.3 °F (3.5 °C).

1- 58

FEATURES OF YOUR HYUNDAI

AM reception

Ionosphere

FM radio station

Unobstructed area

Mountains

Buildings

SSAR011A

Obstructed area

Iron bridges

SSAR012A

AM broadcasts can be received at greater dis- tances than FM broadcasts. This is because AM radio waves are transmitted at low fre- quency. These long, low frequency radio waves can follow the curvature of the earth rather than travelling straight out into the atmosphere. In addition, they curve around obstructions so that they can provide better signal coverage.

FM broadcasts are transmitted at high frequen- cy and do not bend to follow the earth's surface. Because of this, FM broadcasts generally begin to fade at short distances from the station. Also, FM signals are easily affected by buildings, mountains, or other obstructions. These can result in certain listening conditions which might lead you to believe a problem exists with your radio. The following conditions are normal and do not indicate radio trouble:

B750A02A-AAT STEREO SOUND SYSTEM How Car Audio Works

FM reception

Ionosphere

SSAR010A

AM and FM radio signals are broadcast from transmitter towers located around your city. They are intercepted by the radio antenna on your car. This signal is then received by the radio and sent to your car speakers. When a strong radio signal has reached your vehicle, the precise engineering of your audio system ensures high quality reproduction. How- ever, in some cases the signal coming to your vehicle is not strong and clear. This can be due to factors such as the distance from the radio station, closeness of other strong radio stations or the presence of buildings, bridges or other large obstructions in the area.

1- 59

FEATURES OF YOUR HYUNDAI

SSAR013A

SSAR014A

o Fading - As your car moves away from the radio station, the signal will weaken and sound will begin to fade. When this occurs, we suggest that you select another stronger station.

o Flutter/Static - Weak FM signals or large obstructions between the transmitter and your radio can disturb the signal causing static or fluttering noises to occur. Reducing the treble level may lessen this effect until the disturbance clears.

o Station Swapping - As a FM signal weak- ens, another more powerful signal near the same frequency may begin to play. This is because your radio is designed to lock onto the clearest signal. If this occurs, select another station with a stronger signal.

o Multi-Path Cancellation - Radio signals be- ing received from several directions can cause distortion or fluttering. This can be caused by a direct and reflected signal from the same station, or by signals from two stations with close frequencies. If this oc- curs, select another station until the condi- tion has passed.

1- 60

B750B02Y-AAT Using a cellular phone or a two-way radio When a cellular phone is used inside the ve- hicle, noise may be produced from the audio equipment. This does not mean that something is wrong with the audio equipment. In such a case, use the cellular phone at a place as far as possible from the audio equipment.

CAUTION: When using a communication system such as a cellular phone or a radio set inside the vehicle, a separate external antenna must be fitted. When a cellular phone or a radio set is used with an internal antenna alone, it may interfere with the vehicle's electrical system and adversely affect safe operation of the vehicle.

WARNING: Don't use a cellular phone when you are driving, you must stop at a safe place to use a cellular phone.

H240A01O-GAT STEREO RADIO OPERATION (H250) (If Installed)

FEATURES OF YOUR HYUNDAI

5. BAND Selector

3.

TREBLE/FADER Control Knob (TREB/FAD)

6. PRESET Buttons

2. BASS/BALANCE Control Knob (BASS/BAL)

4. TUNE/SEEK Select Button

7. SCAN Button

1. POWER ON/OFF, VOLUME Control Knob

H250A01GK

1- 61

H240B03O-GAT 1. POWER ON-OFF Control Knob The radio unit may be operated when the ignition key is in the “ACC” or “ON” position. Press the knob to switch the power on. The LCD shows the radio frequency in the radio mode or the tape direction indicator in the tape mode. To switch the power off, press the knob again.

VOLUME Control Rotate the knob clockwise to increase the volume and turn the knob counterclockwise to reduce the volume.

2. BASS Control Knob Press to pop the knob out and turn to the left or right for the desired bass tone.

BAL (Balance Control) Knob Pull the bass control knob further out. Turn the control knob clockwise to emphasize right speaker sound. (Left speaker sound will be attenuated) When the control knob is turned counterclock- wise, left speaker sound will be emphasized. (Right speaker sound will be attenuated)

3. TREB (Treble Control) Knob Press to pop the knob out and turn to the left or right for the desired treble tone.

1- 62

FEATURES OF YOUR HYUNDAI

FAD (Fader Control) Knob Pull the treble control knob further out. Turn the control knob counterclockwise to em- phasize front speaker sound. (Rear speaker sound will be attenuated) When the control knob is turned clockwise, rear speaker sound will be emphasized. (Front speaker sound will be attenuated)

4. TUNE (Manual) Select Button Press the side or side to increase or to decrease the frequency. Press either button and hold down to continuously scroll. Release button once the desired station is reached.

SEEK Operation (Automatic Channel Selection) Press the TUNE select button 1 sec or more.Releasing will automatically tune to the next available station with a beep sound. When the side is pressed longer than 1
second, releasing will automatically tune to the next higher frequency and when the side is pressed longer than 1 second, releasing will automatically tune to the next lower frequency.

5. BAND Selector Pressing the button changes the AM, FM1
and FM2 bands. The mode selected is dis- played on LCD.

FM/AM

6. PRESET STATION SELECT Button Six (6) stations for AM, FM and FM2 respec- tively can be preset in the electronic memory circuit on this unit.

HOW TO PRESET STATIONS Six AM and twelve FM stations may be pro- grammed into the memory of the radio. Then, by simply pressing the band select button and/ or one of the six station select buttons, you may recall any of these stations instantly. To program the stations, follow these steps:

o Press band selector to set the band for AM,

FM, or FM2.

o Select the desired station to be stored by

seek or manual tuning.

o Determine the preset station select button

you wish to use to access that station.

o Press the station select button for more than two seconds. A select button indicator will show in the display indicating which select button you have depressed. The frequency display will flash after it has been stored into the memory with a beep sound. You should then release the button, and proceed to program the next desired station. A total of 18 stations can be pro- grammed by selecting one AM and two FM stations per button.

o When completed, any preset station may be recalled by selecting AM, FM or FM2
band and the appropriate station button.

FEATURES OF YOUR HYUNDAI

7. SCAN Button When the scan button is pressed, the fre- quency will increase and the receivable sta- tions will be tuned in one after another, receiv- ing each station for 5 seconds. To stop scan- ning, press the scan button again.

1- 63

H240C01O-GAT CASSETTE TAPE PLAYER OPERATION (H250) (If Installed)

FEATURES OF YOUR HYUNDAI

3. TAPE PROGRAM Button

6. TAPE SLOT

2. AUTO MUSIC SELECT Button

4. EJECT Button

1.

FF/REW Button

5. DOLBY SELECT Button

1- 64

H250A01GK

FEATURES OF YOUR HYUNDAI

NOTE: When tape operation is abnormal or ER8 fault code is displayed, press the eject button more than 5 seconds to reset the deck func- tion.

4. EJECT Button o When the EJECT button is pressed with the

cassette loaded, the cassette is ejected.

o When the EJECT button is pressed during

the FF/REW, the cassette is ejected.

5. DOLBY SELECT Button If you get background noise during PLAY, you can reduce this considerably by merely press- ing DOLBY SELECT button. If you want to release, press the button again.

H240A03O-GAT 1. FF/REW Button o The FF (fast forward tape winding) starts when the button is pressed during the PLAY or REW.

o The play starts when the button is press-

ed again during the FF.

o The REW (rewinding) starts when the bu-

tton is pressed during the PLAY or FF.

o The play starts when the button is press-

ed again during the REW.

2. AUTO MUSIC SELECT Button Press the button to find the starting point of each song in a prerecorded music tape. The quiet space between songs (must have at least a 4 sec. gap) can be accepted by the AUTO MUSIC SELECT button.

o Pressing the button will play the beginn-

ing of the next music segment.

o Pressing the button will start replay at the

beginning of the music just listened to.

3. TAPE PROGRAM Button This allows you to play the reverse side of the tape by merely depressing the program button. An arrow will appear in the display to show tape direction.

1- 65

B250A01GK-GAT CD AUTO CHANGER (H250) (If Installed)

FEATURES OF YOUR HYUNDAI

1. CD CHANGER Select Button

3. TRACK UP/DOWN

6. SCAN Button

4. FF/REW Button

5. REPEAT Button

2. DISC Select Button

H250A01GK

1- 66

B260F01GK-AAT The CD auto changer is located in the right side of the quarter trim.

o To use the CD auto changer.

1. Open the sliding lid of the CD auto chang-

er.

2. To eject the compact disc magazine, press the EJECT button located inside the CD auto changer. Insert the discs into the magazine.

3. 4. Push the magazine into the CD auto

changer and close the sliding lid.

o The CD auto changer can be used when the ignition switch is in either the "ON" or "ACC" position.

1. CD Select Button When the CD changer magazine contains discs, press the "CDC" button and the CD changer can be used even if the radio is being used. The Hyundai CD changer can hold up to eight discs. The disc number will be lit, and the track num- ber, and elapsed time will be displayed.

2. DISC Select Button To select the CD you want, push " " to cha- nge the disc number.

TUNE DISC

FEATURES OF YOUR HYUNDAI

3. TRACK UP/DOWN o The desired track on the disc currently being played can be selected using the track num- ber.

o Press once to skip forward to the begin- ning of the next track. Press once to skip back to the beginning of the track.

4. FF/REW ( / ) If you want to fast forward or reverse through the compact disc track, push and hold in the FF ( ) or REW ( ) button. When you release the button, the compact disc player will resume playing.

5. REPEAT o To repeat the music you are listening to, press the RPT button. To cancel , press again.

o If you do not release RPT operation when the track ends, it will automatically be re- played. This process will be continued until you push the button again.

6. SCAN Button o Press the SCAN button to playback the first

10 seconds of each track.

o Press the SCAN button again within 10 sec.

for the desired track.

NOTE: o When replacing the fuse, replace it with a

fuse having the correct capacity.

o This equipment is designed to be used only in a 12 volt DC battery system with negative ground.

o This unit is made of precision parts. Do not attempt to disassemble or adjust any parts.

o When driving your vehicle, be sure to keep the volume of the unit set low enough to allow you to hear sounds com- ing from the outside.

1- 67

H260A01O-AAT STEREO RADIO OPERATION (H260) (If Installed)

FEATURES OF YOUR HYUNDAI

3. BASS/TREBLE Control Knob

4. SCAN Button