2003 Hyundai Tiburon Owners Manual

3. Remove the filter cover and replace the

4.

filter. Installation is the reverse order of disassem- bly.

HGK012

When the "Defrost" button is pressed, the " " mode will be automatically selected and the air will be discharged through the windshield de- frost vents. To assist in defrosting, the air conditioning will operate if ambient temperature is higher than 38.3 °F (3.5 °C) and automatically turns off if the ambient temperature drops below 38.3 °F (3.5 °C).

1- 58

FEATURES OF YOUR HYUNDAI

AM reception

Ionosphere

FM radio station

Unobstructed area

Mountains

Buildings

SSAR011A

Obstructed area

Iron bridges

SSAR012A

AM broadcasts can be received at greater dis- tances than FM broadcasts. This is because AM radio waves are transmitted at low fre- quency. These long, low frequency radio waves can follow the curvature of the earth rather than travelling straight out into the atmosphere. In addition, they curve around obstructions so that they can provide better signal coverage.

FM broadcasts are transmitted at high frequen- cy and do not bend to follow the earth's surface. Because of this, FM broadcasts generally begin to fade at short distances from the station. Also, FM signals are easily affected by buildings, mountains, or other obstructions. These can result in certain listening conditions which might lead you to believe a problem exists with your radio. The following conditions are normal and do not indicate radio trouble:

B750A02A-AAT STEREO SOUND SYSTEM How Car Audio Works

FM reception

Ionosphere

SSAR010A

AM and FM radio signals are broadcast from transmitter towers located around your city. They are intercepted by the radio antenna on your car. This signal is then received by the radio and sent to your car speakers. When a strong radio signal has reached your vehicle, the precise engineering of your audio system ensures high quality reproduction. How- ever, in some cases the signal coming to your vehicle is not strong and clear. This can be due to factors such as the distance from the radio station, closeness of other strong radio stations or the presence of buildings, bridges or other large obstructions in the area.

1- 59

FEATURES OF YOUR HYUNDAI

SSAR013A

SSAR014A

o Fading - As your car moves away from the radio station, the signal will weaken and sound will begin to fade. When this occurs, we suggest that you select another stronger station.

o Flutter/Static - Weak FM signals or large obstructions between the transmitter and your radio can disturb the signal causing static or fluttering noises to occur. Reducing the treble level may lessen this effect until the disturbance clears.

o Station Swapping - As a FM signal weak- ens, another more powerful signal near the same frequency may begin to play. This is because your radio is designed to lock onto the clearest signal. If this occurs, select another station with a stronger signal.

o Multi-Path Cancellation - Radio signals be- ing received from several directions can cause distortion or fluttering. This can be caused by a direct and reflected signal from the same station, or by signals from two stations with close frequencies. If this oc- curs, select another station until the condi- tion has passed.

1- 60

B750B02Y-AAT Using a cellular phone or a two-way radio When a cellular phone is used inside the ve- hicle, noise may be produced from the audio equipment. This does not mean that something is wrong with the audio equipment. In such a case, use the cellular phone at a place as far as possible from the audio equipment.

CAUTION: When using a communication system such as a cellular phone or a radio set inside the vehicle, a separate external antenna must be fitted. When a cellular phone or a radio set is used with an internal antenna alone, it may interfere with the vehicle's electrical system and adversely affect safe operation of the vehicle.

WARNING: Don't use a cellular phone when you are driving, you must stop at a safe place to use a cellular phone.

H240A01O-GAT STEREO RADIO OPERATION (H250) (If Installed)

FEATURES OF YOUR HYUNDAI

5. BAND Selector

3.

TREBLE/FADER Control Knob (TREB/FAD)

6. PRESET Buttons

2. BASS/BALANCE Control Knob (BASS/BAL)

4. TUNE/SEEK Select Button

7. SCAN Button

1. POWER ON/OFF, VOLUME Control Knob

H250A01GK

1- 61

H240B03O-GAT 1. POWER ON-OFF Control Knob The radio unit may be operated when the ignition key is in the “ACC” or “ON” position. Press the knob to switch the power on. The LCD shows the radio frequency in the radio mode or the tape direction indicator in the tape mode. To switch the power off, press the knob again.

VOLUME Control Rotate the knob clockwise to increase the volume and turn the knob counterclockwise to reduce the volume.

2. BASS Control Knob Press to pop the knob out and turn to the left or right for the desired bass tone.

BAL (Balance Control) Knob Pull the bass control knob further out. Turn the control knob clockwise to emphasize right speaker sound. (Left speaker sound will be attenuated) When the control knob is turned counterclock- wise, left speaker sound will be emphasized. (Right speaker sound will be attenuated)

3. TREB (Treble Control) Knob Press to pop the knob out and turn to the left or right for the desired treble tone.

1- 62

FEATURES OF YOUR HYUNDAI

FAD (Fader Control) Knob Pull the treble control knob further out. Turn the control knob counterclockwise to em- phasize front speaker sound. (Rear speaker sound will be attenuated) When the control knob is turned clockwise, rear speaker sound will be emphasized. (Front speaker sound will be attenuated)

4. TUNE (Manual) Select Button Press the side or side to increase or to decrease the frequency. Press either button and hold down to continuously scroll. Release button once the desired station is reached.

SEEK Operation (Automatic Channel Selection) Press the TUNE select button 1 sec or more.Releasing will automatically tune to the next available station with a beep sound. When the side is pressed longer than 1
second, releasing will automatically tune to the next higher frequency and when the side is pressed longer than 1 second, releasing will automatically tune to the next lower frequency.

5. BAND Selector Pressing the button changes the AM, FM1
and FM2 bands. The mode selected is dis- played on LCD.

FM/AM

6. PRESET STATION SELECT Button Six (6) stations for AM, FM and FM2 respec- tively can be preset in the electronic memory circuit on this unit.

HOW TO PRESET STATIONS Six AM and twelve FM stations may be pro- grammed into the memory of the radio. Then, by simply pressing the band select button and/ or one of the six station select buttons, you may recall any of these stations instantly. To program the stations, follow these steps:

o Press band selector to set the band for AM,

FM, or FM2.

o Select the desired station to be stored by

seek or manual tuning.

o Determine the preset station select button

you wish to use to access that station.

o Press the station select button for more than two seconds. A select button indicator will show in the display indicating which select button you have depressed. The frequency display will flash after it has been stored into the memory with a beep sound. You should then release the button, and proceed to program the next desired station. A total of 18 stations can be pro- grammed by selecting one AM and two FM stations per button.

o When completed, any preset station may be recalled by selecting AM, FM or FM2
band and the appropriate station button.

FEATURES OF YOUR HYUNDAI

7. SCAN Button When the scan button is pressed, the fre- quency will increase and the receivable sta- tions will be tuned in one after another, receiv- ing each station for 5 seconds. To stop scan- ning, press the scan button again.

1- 63

H240C01O-GAT CASSETTE TAPE PLAYER OPERATION (H250) (If Installed)

FEATURES OF YOUR HYUNDAI

3. TAPE PROGRAM Button

6. TAPE SLOT

2. AUTO MUSIC SELECT Button

4. EJECT Button

1.

FF/REW Button

5. DOLBY SELECT Button

1- 64

H250A01GK

FEATURES OF YOUR HYUNDAI

NOTE: When tape operation is abnormal or ER8 fault code is displayed, press the eject button more than 5 seconds to reset the deck func- tion.

4. EJECT Button o When the EJECT button is pressed with the

cassette loaded, the cassette is ejected.

o When the EJECT button is pressed during

the FF/REW, the cassette is ejected.

5. DOLBY SELECT Button If you get background noise during PLAY, you can reduce this considerably by merely press- ing DOLBY SELECT button. If you want to release, press the button again.

H240A03O-GAT 1. FF/REW Button o The FF (fast forward tape winding) starts when the button is pressed during the PLAY or REW.

o The play starts when the button is press-

ed again during the FF.

o The REW (rewinding) starts when the bu-

tton is pressed during the PLAY or FF.

o The play starts when the button is press-

ed again during the REW.

2. AUTO MUSIC SELECT Button Press the button to find the starting point of each song in a prerecorded music tape. The quiet space between songs (must have at least a 4 sec. gap) can be accepted by the AUTO MUSIC SELECT button.

o Pressing the button will play the beginn-

ing of the next music segment.

o Pressing the button will start replay at the

beginning of the music just listened to.

3. TAPE PROGRAM Button This allows you to play the reverse side of the tape by merely depressing the program button. An arrow will appear in the display to show tape direction.

1- 65

B250A01GK-GAT CD AUTO CHANGER (H250) (If Installed)

FEATURES OF YOUR HYUNDAI

1. CD CHANGER Select Button

3. TRACK UP/DOWN

6. SCAN Button

4. FF/REW Button

5. REPEAT Button

2. DISC Select Button

H250A01GK

1- 66

B260F01GK-AAT The CD auto changer is located in the right side of the quarter trim.

o To use the CD auto changer.

1. Open the sliding lid of the CD auto chang-

er.

2. To eject the compact disc magazine, press the EJECT button located inside the CD auto changer. Insert the discs into the magazine.

3. 4. Push the magazine into the CD auto

changer and close the sliding lid.

o The CD auto changer can be used when the ignition switch is in either the "ON" or "ACC" position.

1. CD Select Button When the CD changer magazine contains discs, press the "CDC" button and the CD changer can be used even if the radio is being used. The Hyundai CD changer can hold up to eight discs. The disc number will be lit, and the track num- ber, and elapsed time will be displayed.

2. DISC Select Button To select the CD you want, push " " to cha- nge the disc number.

TUNE DISC

FEATURES OF YOUR HYUNDAI

3. TRACK UP/DOWN o The desired track on the disc currently being played can be selected using the track num- ber.

o Press once to skip forward to the begin- ning of the next track. Press once to skip back to the beginning of the track.

4. FF/REW ( / ) If you want to fast forward or reverse through the compact disc track, push and hold in the FF ( ) or REW ( ) button. When you release the button, the compact disc player will resume playing.

5. REPEAT o To repeat the music you are listening to, press the RPT button. To cancel , press again.

o If you do not release RPT operation when the track ends, it will automatically be re- played. This process will be continued until you push the button again.

6. SCAN Button o Press the SCAN button to playback the first

10 seconds of each track.

o Press the SCAN button again within 10 sec.

for the desired track.

NOTE: o When replacing the fuse, replace it with a

fuse having the correct capacity.

o This equipment is designed to be used only in a 12 volt DC battery system with negative ground.

o This unit is made of precision parts. Do not attempt to disassemble or adjust any parts.

o When driving your vehicle, be sure to keep the volume of the unit set low enough to allow you to hear sounds com- ing from the outside.

1- 67

H260A01O-AAT STEREO RADIO OPERATION (H260) (If Installed)

FEATURES OF YOUR HYUNDAI

3. BASS/TREBLE Control Knob

4. SCAN Button

6. BAND Selector

7. PRESET Button

5. TUNE/SEEK Select Button

1. POWER ON-OFF/VOLUME/BALANCE Control Knob

2. FADER Control Knob

H260A01O

1- 68

H260B03E-AAT 1. POWER ON-OFF Control Knob The radio unit may be operated when the igni- tion key is in the “ACC” or “ON” position. Press the knob to switch the power on. The LCD shows the radio frequency in the radio mode or the CD track indicator in either the CD mode or CD AUTO CHANGER mode. To switch the power off, press the knob again.

VOLUME Control Rotate the knob clockwise to increase the vol- ume and turn the knob counterclockwise to reduce the volume.

BALANCE Control Pull and turn the control knob clockwise to emphasize right speaker sound (Left speaker sound will be attenuated). When the control knob is turned counterclockwise, left speaker sound will be emphasized. (Right speaker sound will be attenuated)

2. FAD (Fader Control) Knob Turn the control knob counterclockwise to em- phasize front speaker sound. (Rear speaker sound will be attenuated) When the control knob is turned clockwise, rear speaker sound will be emphasized. (Front speaker sound will be attenuated)

FEATURES OF YOUR HYUNDAI

3. BASS Control Knob Press to pop the knob out and turn to the left or right for the desired bass tone.

TREB (Treble Control) Knob Pull the bass control knob further out. Turn to the left or right for the desired treble tone.

4. SCAN Button When the scan button is pressed, the fre- quency will increase and the receivable sta- tions will be tuned in one after another, receiv- ing each station for 5 seconds. To stop scan- ning, press the scan button again.

5. TUNE (Manual) Select Button Press the ( ) side or ( ) side to increase or to decrease the frequency. Press either button and hold down to continuously scroll. Release button once the desired station is reached.

SEEK Operation (Automatic Channel Selection) Press the TUNE select button for 1 sec or more. Releasing it will automatically tune to the next available station with a beep sound. When the ( ) side is pressed longer than 1
second, releasing will automatically tune to the next higher frequency and when the ( ) side is pressed longer than 1 second, releasing will automatically tune to the next lower frequency.

6. BAND Selector Pressing the button changes the AM, FM1
and FM2 bands. The mode selected is dis- played on LCD.

FM/AM

7. PRESET STATION SELECT Button Six (6) stations for AM, FM or FM2 respectively can be preset in the electronic memory circuit on this unit.

HOW TO PRESET STATIONS Six AM and twelve FM stations may be pro- grammed into the memory of the radio. Then, by simply pressing the band select button and/ or one of the six station select buttons, you may recall any of these stations instantly. To pro- gram the stations, follow these steps:

o Press band selector to set the band for AM,

FM or FM2.

o Select the desired station to be stored by

seek, scan or manual tuning.

o Determine the preset station select button

you wish to use to access that station.

o Press the station select button for more than two seconds. A select button indicator will show in the display indicating which select button you have depressed. The frequency display will flash after it has been stored into the memory.

1- 69

FEATURES OF YOUR HYUNDAI

You should then release the button, and proceed to program the next desired station. A total of 18 stations can be programmed by selecting one AM and two FM stations per button.

o When completed, any preset station may be recalled by selecting AM, FM or FM2 band and the appropriate station button.

1- 70

H260B01O-AAT COMPACT DISC PLAYER OPERATION (H260) (If Installed)

FEATURES OF YOUR HYUNDAI

4. SCAN Button

1.Playing CD

3. TRACK UP/DOWN

6. EJECT Button

2. FF/REW Button

5. REPEAT Button

H260A01O

1- 71

o This unit is made of precision parts. Do not attempt to disassemble or adjust any parts.

o When driving your vehicle, be sure to keep the volume of the unit set low enough to allow you to hear sounds com- ing from the outside.

o Do not expose this equipment (including the speakers) to water or excessive mois- ture.

B260D01O-AAT 1. Playing CD o Insert the CD with the label facing upward. o Insert the CD to start CD playback, during

radio operation.

o When a disc is in the CD deck, if you press the play button, the CD player will begin playing even if the radio is being used.

o The CD player can be used when the igni- tion switch is in either the "ON" or "ACC" position.

2. FF/REW ( / ) If you want to fast forward or reverse through the compact disc track, push and hold in the FF ( ) or REW ( ) button. When you release the button, the compact disc player will resume playing.

3. TRACK UP/DOWN o The desired track on the disc currently being played can be selected using the track number. o Press once to skip forward to the beginn- ing of the next track. Press once to skip back to the beginning of the track.

4. SCAN Button o Press the SCAN button to playback the first

10 seconds of each track.

o Press the SCAN button again within 10 sec.

for the desired track.

1- 72

FEATURES OF YOUR HYUNDAI

5. REPEAT Button o To repeat the music you are listening to, press the RPT button. To cancel , press again.

o If you do not release RPT operation, when the track ends, it will automatically be re- played. This process will be continued until you push the button again.

6. EJECT Button When the EJECT button is pressed with the CD loaded, the CD is ejected.

NOTE: o To assure proper operation of the unit, keep the vehicle interior temperature within a normal range by using the vehicle’s air conditioning or heating sys- tem.

o When replacing the fuse, replace it with a

fuse having the correct capacity.

o The preset station frequencies are all erased when the car battery is discon- nected. Therefore, all data will have to be set again if this should occur.

o Do not add any oil to the rotating parts. Keep magnets, screwdrivers and other metallic objects away from the tape mechanism and head.

o This equipment is designed to be used only in a 12 volt DC battery system with negative ground.

B260E01E-AAT CD AUTO CHANGER (H260) (If Installed)

FEATURES OF YOUR HYUNDAI

6. SCAN Button

1. CD Select Button

3. TRACK UP/DOWN

4. FF/REW Button

5. REPEAT Button

2. DISC Select Button

H260A01O

1- 73

NOTE: o When replacing the fuse, replace it with a

fuse having the correct capacity.

o This equipment is designed to be used only in a 12 volt DC battery system with negative ground.

o This unit is made of precision parts. Do not attempt to disassemble or adjust any parts.

o When driving your vehicle, be sure to keep the volume of the unit set low enough to allow you to hear sounds com- ing from the outside.

FEATURES OF YOUR HYUNDAI

3. TRACK UP/DOWN o The desired track on the disc currently being played can be selected using the track num- ber.

o Press once to skip forward to the begin- ning of the next track. Press once to skip back to the beginning of the track.

4. FF/REW ( / ) If you want to fast forward or reverse through the compact disc track, push and hold in the FF ( ) or REW ( ) button. When you release the button, the compact disc player will resume playing.

5. REPEAT o To repeat the music you are listening to, press the RPT button. To cancel, press again.

o If you do not release RPT operation when the track ends, it will automatically be re- played. This process will be continued until you push the button again.

6. SCAN Button o Press the SCAN button to playback the first

10 seconds of each track.

o Press the SCAN button again within 10 sec.

for the desired track.

B260F01GK-AAT The CD auto changer is located in the right side of the quater trim.

o To use the CD auto changer.

1. Open the sliding lid of the CD auto chang-

er.

2. To eject the compact disc magazine, press the EJECT button located inside the CD auto changer. Insert the discs into the magazine.

3. 4. Push the magazine into the CD auto

changer and close the sliding lid.

o The CD auto changer can be used when the ignition switch is in either the "ON" or "ACC" position.

1. CD Select Button When the CD changer magazine contains discs, press the "CD" button and the CD changer can be used even if the radio is being used. The Hyundai CD changer can hold up to eight discs. The disc number will be lit, and the track num- ber, and elapsed time will be displayed.

2. DISC Select Button To select the CD you want, push " " to change the disc number.

TUNE DISC

1- 74

H290A01FC-GAT STEREO RADIO OPERATION (H280) (If Installed)

FEATURES OF YOUR HYUNDAI

1. POWER ON/OFF VOLUME Control Knob

8. BEST STATION MEMORY

or SCAN Button (If installed)

7. EQUALIZER Button

3. TREBLE/FAD Konb

2. BASS/BALANCE Control Knob

5. PRESET Buttons

4. TUNE/SEEK Select Button

6. BAND Select Button

H290A01O

1- 75

H290B03E-GAT 1. POWER ON-OFF Control Knob The radio unit may be operated when the igni- tion key is in the "ACC" or "ON" position. Press the button to switch the power on. The display shows the radio frequency in the radio mode, the tape direction indicator in the tape mode or CD track in either the CD mode or CD AUTO CHANGER mode. To switch the power off, press the button again.

VOLUME Control Rotate the knob clockwise to increase the vol- ume and turn the knob counterclockwise to reduce the volume.

2. BASS/BALANCE Control Knob BASS Control Knob Press to pop the knob out. To increase the bass, rotate the knob clockwise, while to de- crease the bass, rotate the knob counterclock- wise.

BALANCE Control knob Pull the Bass control knob out further. Rotate the knob clockwise to emphasize right speaker sound. (Left speaker sound will be attenuated) When the control knob is turned counterclock- wise, left speaker sound will be emphasized (Right speaker sound will be attenuated).

1- 76

FEATURES OF YOUR HYUNDAI

3. TREBLE/FAD Knob TREBLE Control Knob Press to pop the knob out and turn to the left or right for the desired treble tone.

5. PRESET STATION Select Buttons Six (6) stations for AM, FM and FM2 respec- tively can be preset in the electronic memory circuit.

FAD (Fader Control) Knob Pull the Treble control knob out further. Turn the control knob counterclockwise to emphasize front speaker sound. (Rear speaker sound will be attenuated) When the control knob is turned clockwise, rear speaker sound will be empha- sized. (Front speaker sound will be attenuated)

4. TUNE (Manual) Select Button Press the ( ) side or ( ) side to increase or to decrease the frequency. Press either button and hold down to continuously scroll. Release button once the desired station is reached.

SEEK Operation (Automatic Channel Selection) Press the TUNE select button for 0.5 sec or more. Releasing it will automatically tune to the next available station with a beep sound. When the ( ) side is pressed longer than 0.5
second, releasing will automatically tune to the next higher frequency and when the ( ) side is pressed longer than 0.5 second, releasing will automatically tune to the next lower frequency.

HOW TO PRESET STATIONS Six AM and twelve FM stations may be pro- grammed into the memory of the radio. Then, by simply pressing the band select button and/ or one of the six station select buttons, you may recall any of these stations instantly. To pro- gram the stations, follow these steps:

o Press band selector to set the band for AM,

FM or FM2.

o Select the desired station to be stored by

seek or manual tuning.

o Determine the preset station select button

you wish to use to access that station.

o Press the station select button for more than two seconds. A select button indicator will show in the display indicating which select button you have depressed. The frequency display will flash after it has been stored into the memory with beep sound. You should then release the button, and proceed to program the next desired station. A total of 18 stations can be programmed by selecting one AM and two FM station per button.

o When completed, any preset station may be recalled by selecting AM, FM or FM2 band and the appropriate station button.

FEATURES OF YOUR HYUNDAI

6. BAND Selector Pressing the button changes the AM, FM1
and FM2 bands. The mode selected is shown on the display.

FM/AM

7. EQUALIZER Button Press the EQ button to select the CLASSIC, JAZZ, ROCK and DEFEAT MODE for the de- sired tone quality. Each press of the button changes the display as follows;

CLASSIC fi

JAZZ fi

ROCK fi

DEFEAT

8. Best Station Memory Button (BSM)

(If installed)

When the BSM button is pressed for two sec- onds or longer, the six channels from the high- est field intensity are selected next and stored in memory. The stations selected are stored in the sequence frequency from the first preset key.

SCAN Button (If installed) When the scan button is pressed, the fre- quency will increase and the receivable sta- tions will be tuned in one after another, receiv- ing each station for 5 seconds. To stop scan- ning, press the scan button again.

1- 77

› H290C01FC-GAT CASSETTE TAPE PLAYER OPERATION (H280) (If Installed)

FEATURES OF YOUR HYUNDAI

5. EQUALIZER Button

4. TAPE EJECT Button

2. AUTO MUSIC Select Button

H290A01O

6. DOLBY Button

1. FF/REW Button

3. TAPE PROGRAM Button

1- 78

FEATURES OF YOUR HYUNDAI

4. TAPE EJECT button o When the button is pressed with the

cassette loaded, the cassette is ejected.

o When the button is pressed during the

FF/REW mode, the cassette is ejected.

5. EQ Button Press the EQ button to select the CLASSIC, JAZZ, ROCK and DEFEAT MODE for the de- sired tone quality. Each press of the button changes the display as follows;

CLASSIC fi

JAZZ fi

ROCK fi

DEFEAT

6. DOLBY Button If you get background noise during tape PLAY, you can reduce this considerably by merely pressing the DOLBY button. If you want to cancel the DOLBY feature, press the button again.

H290D01O-GAT 1. FF/REW Button o Fast forward tape winding starts when the FF ( ) button is pressed during the PLAY or REW mode.

o Tape play starts when the FF ( ) button

is pressed again during the FF mode. o Tape rewinding starts when the REW

( ) button is pressed during the PLAY or FF mode.

o Tape play starts when the REW ( ) button

pressed again during the REW mode.

2. AUTO MUSIC Select Button Press the button to find the starting point of each song in a prerecorded music tape. The quiet space between songs (must have at least a 4 sec. gap) can be accepted by the AUTO MUSIC Select button.

o Pressing the button will play the beginn-

ing of the next music segment.

o Pressing the button will start replay at the beginning of the music just listened to.

3. TAPE PROGRAM Button This allows you to play the reverse side of the tape by merely depressing the program button. An arrow will appear in the display to show tape direction.

1- 79

› FEATURES OF YOUR HYUNDAI

H290E01FC-GAT COMPACT DISC PLAYER OPERATION (H280) (If Installed)

6. CD EJELT Button

7. SCAN Button (If installed)

5. EQUALIZER Button

3. TRACK UP/DOWN

H290A01O

4. REPEAT

2. FF/REW Button

1. CD Select Button

1- 80

H290F01O-GAT 1. CD Select Button o Insert the CD with the label facing upward. o Insert the CD to start CD playback, during

radio operation or cassette tape playing.

o When a disc is in the CD deck, if you press the play button the CD player will begin playing even if the radio or cassette player is being used.

o The CD player can be used when the igni- tion switch is in either the "ON" or "ACC" position.

2. FF/REW ( / ) If you want to fast forward or reverse through the compact disc track, push and hold in the FF ( ) or REW ( ) button. When you release the button, the compact disc player will resume playing.

3. TRACK UP/DOWN o The desired track on the disc currently being played can be selected using the track num- ber.

o Press button once to skip forward to the beginning of the next track. Press button once to skip back to the beginning of the track.

FEATURES OF YOUR HYUNDAI

4. REPEAT o To repeat the music you are listening to, press the RPT button. To cancel, press again.

o If you do not release RPT operation when the track ends, it will automatically be re- played. This process will be continued until you push the button again.

5. EQUALIZER Button Press the EQ button to select the CLASSIC, JAZZ, ROCK and DEFEAT MODE for the de- sired tone quality. Each press of the button changes the display as follows;

CLASSIC fi

JAZZ fi

ROCK fi

DEFEAT

6. CD EJECT Button When the button is pressed with the CD loaded, the CD is ejected.

7. SCAN Button (If installed) o Press the SCAN button to playback the first

10 seconds of each track.

o Press the SCAN button again within 10 sec.

for the desired track.

NOTE: o To assure proper operation of the unit, keep the vehicle interior temperature within a normal range by using the vehicle’s air conditioning or heating sys- tem.

o When replacing the fuse, replace it with a

fuse having the correct capacity.

o The preset station frequencies are all erased when the car battery is discon- nected. Therefore, all data will have to be set again if this should occur.

o Do not add any oil to the rotating parts. Keep magnets, screwdrivers and other metallic objects away from the tape mechanism and head.

o This equipment is designed to be used only in a 12 volt DC battery system with negative ground.

o This unit is made of precision parts. Do not attempt to disassemble or adjust any parts.

o When driving your vehicle, be sure to keep the volume of the unit set low enough to allow you to hear sounds com- ing from the outside.

o Do not expose this equipment (including the speakers and tape) to water or exces- sive moisture.

1- 81

› H290G01FC-GAT CD AUTO CHANGER (H280) (If Installed)

FEATURES OF YOUR HYUNDAI

6. SCAN Button (If installed)

7. EQ Button

3. TRACK UP/DOWN

5. REPEAT

2.DISC Select Button

1. CD CHANGER Select Button

4. FF/REW Button

H290A01O

1- 82

FEATURES OF YOUR HYUNDAI

3. TRACK UP/DOWN o The desired track on the disc currently being played can be selected using the track num- ber.

o Press once to skip forward to the begin- ning of the next track. Press once to skip back to the beginning of the track.

4. FF/REW ( / ) If you want to fast forward or reverse through the compact disc track, push and hold in the FF ( ) or REW ( ) button. When you release the button, the compact disc player will resume playing.

5. REPEAT o To repeat the music you are listening to, press the RPT button. To cancel, press again.

o If you do not release RPT operation when the track ends, it will automatically be re- played. This process will be continued until you push the button again.

B290H01GK-GAT The CD auto changer is located in the right side of the quater trim.

o To use the CD auto changer.

1. Open the sliding lid of the CD auto chang-

er.

2. To eject the compact disc magazine, press the EJECT button located inside the CD auto changer. Insert the discs into the magazine.

3. 4. Push the magazine into the CD auto

changer and close the sliding lid.

o The CD auto changer can be used when the ignition switch is in either "ON" or "ACC" position.

1. CD CHANGER Select Button When the CD changer magazine contains discs, press the "CD/CDC" button and the CD changer can be used even if the radio or cassette player is being used. The Hyundai CD changer can hold up to eight discs. The disc number will be lit, and the track number, and elapsed time will be displayed.

2. DISC Select Button To select the CD you want, push " " to change the disc number.

TUNE DISC

6. SCAN Button (If installed) o Press the SCAN button to playback the first

10 seconds of each track.

o Press the SCAN button again within 10 sec.

for the desired track.

7. EQ Button Press the EQ button to select the CLASSIC, JAZZ, ROCK and DEFEAT MODE for the de- sired tone quality. Each press of the button changes the display as follows;

CLASSIC fi

JAZZ fi

ROCK fi

DEFEAT

NOTE: o When replacing the fuse, replace it with a

fuse having the correct capacity.

o This equipment is designed to be used only in a 12 volt DC battery system with negative ground.

o This unit is made of precision parts. Do not attempt to disassemble or adjust any parts.

o When driving your vehicle, be sure to keep the volume of the unit set low enough to allow you to hear sounds com- ing from the outside.

1- 83

› FEATURES OF YOUR HYUNDAI

B890A01Y-AAT AUDIO FAULT CODE If you see any error indication in the display while using the CD or Tape mode, find the cause in the chart below. If you cannot clear the error indication, take the car to your Hyundai dealer.

INDICATION

CAUSE

SOLUTION

CDP DECK MECHANICAL ERROR (EJECT ERROR, LOADING ERROR)

AFTER RESETTING THE AUDIO, PUSH THE EJECT BUTTON. IF DISC IS NOT EJECTED, CONSULT YOUR HYUNDAI DEALER.

FOCUS ERROR DATA READ ERROR

DISC ERROR

TAPE DECK ERROR TAPE EJECT ERROR

TEMPERATURE IS TOO HIGH

NO DISC IN MAGAZINE NO CD MAGAZINE IN THE AUTO CHANGER

MAKE SURE THE DISC IS NOT SCRATCHED OR DAMAGED. PRESS THE EJECT BUTTON AND PULL OUT THE DISC. THEN INSERT A NORMAL CD DISC.

CHECK IF THE DISC IS INSERTED CORRECTLY IN THE CD PLAYER. MAKE SURE THE DISC IS NOT SCRATCHED OR DAMAGED.

AFTER RESETTING THE AUDIO, PUSH THE EJECT BUTTON. IF TAPE IS NOT EJECTED, CONSULT YOUR HYUNDAI DEALER.

FAULT CODE WILL RESET AUTOMATICALLY WHEN THE TEM- PERATURE RETURNS TO NORMAL.

INSERT DISC IN MAGAZINE OR INSERT CD MAGAZINE IN THE AUTO CHANGER.

Er2

Er3

Er6

Er8

HHH

no CD

1- 84

B850A01F-AAT CARE OF DISC Proper Handling

YL11240B

Handle your disc as shown. Do not drop the disc. Hold the disc so you will not leave finger- prints on the surface. If the surface is scratched, it may cause the pickup to skip signal tracks. Do not affix tape, paper, or gummed labels on the disc. Do not write on the disc.

Damaged Disc Do not attempt to play damaged, warped or cracked discs. These could severely damage the playback mechanism.

HGK031

Storage When not in use, place your discs in their individual case and store them in a cool place away from the sun, heat, and dust. Do not grip or pull out the disc with your hand

FEATURES OF YOUR HYUNDAI

while the disc is being pulled into the unit by the self loading mechanism. Do not pull the unit from the dash immediately after a disc is inserted or the eject switch has been pressed. If the unit is pulled out before an operation is completed, the disc will be unstable in the unit and may be damaged. Do not attempt to insert a disc into the unit when the unit is out of the dash or the power is off.

Keep Your Discs Clean

B860A01A-AAT CARE OF CASSETTE TAPES

FUA1250B

Fingerprints, dust, or soil on the surface of a disc could cause the pickup to skip signal tracks. Wipe the surface clean with a clean soft cloth. If the surface is heavily soiled, dampen a clean soft cloth in a solution of mild neutral detergent to wipe it clean. See drawing.

SSAR040B

Proper care of your cassette tapes will extend the tape life and increase your listening enjoy- ment. Always protect your tapes and cassette cases from direct sunlight, severely cold and dusty conditions. When not in use, cassettes should always be stored in the original protec- tive cassette case. When the vehicle is very hot or cold, allow the interior temperature to be- come more comfortable before listening to your cassettes. o Never leave a cassette inserted in the play- er when not being played. This could dam- age the tape player unit and the cassette tape.

o We strongly recommend against the use of tapes longer than C-60 (60 minutes total). Tapes such as C-120 or C-180 are very thin and do not perform as well in the automotive environment.

1- 85

FEATURES OF YOUR HYUNDAI

Head

Cotton applicator

SSAR042B

o The playback head, capstan and pinch roll- ers will develop a coating of tape residue that can result in deterioration of sound quality, such as a wavering sound. They should be cleaned monthly using a commer- cially available head cleaning tape or spe- cial solution available from audio specialty shops. Follow the supplier’s directions care- fully and never oil any part of the tape player unit.

o Always be sure that the tape is tightly wound on its reel before inserting in the player. Rotate a pencil in the drive sprockets to wind up any slack.

SSAR053B

NOTE: Look at a tape before you insert it. If the tape is loose, tighten it by turning one of the hubs with a pencil or your finger. If the label is peeling off, do not put it in the drive mechanism. . Do not leave tapes sitting where they are exposed to hot, warm, or, high humidity, such as on top of the dashboard or in the player. If a tape is exposed to extreme heat or cold, let it reach a moderate temperature before putting it in the player.

HGK062

o Be sure that the cassette label is not loose or peeling off or tape ejection may be diffi- cult.

o Never touch or soil the actual audio tape

surfaces.

o Keep all magnetized objects, such as elec- tric motors, speakers or transformers away from your cassette tapes and tape player unit.

o Store cassettes in a cool, dry place with the open side facing down to prevent dust from settling in the cassette body.

o Avoid repeated fast reverse usage to replay one given tune or tape section. This can cause poor tape winding to occur, and even- tually cause excessive internal drag and poor audio quality in the cassette. If this occurs, it can sometimes be corrected by fast winding the tape from end to end sever- al times. If this does not correct the problem, do not continue to use the tape in your vehicle.

1- 86

FEATURES OF YOUR HYUNDAI

B870A01A-AAT ANTENNA Fixed Rod Antenna

B870A01A

Your car uses a fixed rod antenna to receive both AM and FM broadcast signals. This antenna is a removable type. To remove the antenna, turn it counterclockwise. To install the antenna, turn it clockwise.

CAUTION: o Be sure to remove the antenna before washing the car in an automatic car wash or it may be damaged.

o When reinstalling your antenna, it is im- portant that it is fully tightened to ensure proper reception.

1- 87

DRIVING YOUR HYUNDAI

2. DRIVING YOUR HYUNDAI

C010A01O-AAT

WARNING: ENGINE EXHAUST CAN BE DANGEROUS!

Engine exhaust fumes can be extremely dangerous. If, at any time, you smell exhaust fumes inside the vehicle, open the windows immediately.

o Do not inhale exhaust fumes. Exhaust fumes contain carbon monoxide, a colorless, odorless gas that can cause unconsciousness and death by asphyxiation.

o Be sure the exhaust system does not leak. The exhaust system should be checked whenever the vehicle is raised to change the oil or for any other purpose. If you hear a change in the sound of the exhaust or if you drive over something that strikes the underneath side of the car, have the exhaust system checked as soon as possible by your Hyundai dealer.

o Do not run the engine in an enclosed area. Letting the engine idle in your garage, even with the garage door open, is a hazardous practice. Never run the engine in your garage any longer than it takes to start the engine and back the car out.

o Avoid idling the engine for prolonged periods with people inside the car. If it is necessary to idle the engine for a prolonged period with people inside the car, be sure to do so only in an open area with the air intake set at "Fresh" and fan operating at one of the higher speeds so fresh air is drawn into the interior.

If you must drive with the tail gate open because you are carrying objects that make this necessary:

1. Close all windows. 2. Open side vents. 3. Set the air intake control at "Fresh", the air flow control at "Floor" or "Face" and the fan at one of the higher speeds.

To assure proper operation of the ventilation system, be sure the ventilation air intakes located just in front of the windshield are kept clear of snow, ice, leaves or other obstructions.

2- 1

C020A01A-AAT BEFORE STARTING THE ENGINE Before you start the engine, you should always:

1. Look around the vehicle to be sure there are no flat tires, puddles of oil, water or other indications of possible trouble.

2. After entering the car, check to be sure the

parking brake is engaged.

3. Check that all windows, and lights are clean. 4. Check that the interior and exterior mirrors

are clean and in position.

5. Check your seat, seatback and headrest to

be sure they are in their proper positions.

6. Lock all the doors. 7. Fasten your seat belt and be sure that all

other occupants have fastened theirs.

8. Turn off all lights and accessories that are

not needed.

9. When you turn the ignition switch to “ON”, check that all appropriate warning lights are operating and that you have sufficient fuel. 10.Check the operation of warning lights and all

bulbs when key is in the “ON” position.

C030A01A-AAT COMBINATION IGNITION SWITCH To Start the Engine o If your Hyundai is equipped with a manual transaxle, place the shift lever in neutral and depress the clutch pedal fully.

o If your Hyundai has an automatic transaxle,

place the shift lever in "P" (park).

2- 2

DRIVING YOUR HYUNDAI

o To start the engine, insert the ignition key and turn it to the "START" position. Release it as soon as the engine starts. Do not hold the key in the "START" position for more than 15 seconds.

NOTE: o For safety, the engine will not start if the clutch pedal is not depressed fully (Man- ual transaxle) or the shift lever is not in “P” or “N” Position (Automatic transaxle). o The ignition key cannot be turned from "ACC" position to "LOCK" position un- less the shift lever is in the "P" (Park) position or the negative battery terminal is disconnected from the battery. To re- move the key, always confirm that the shift lever is securely positioned in "P" (Park) (For Automatic transaxle)

o For additional information about start-

ing, see page 2-3.

C040A01A-AAT KEY POSITIONS

WARNING: The engine should not be turned off or the key removed from the ignition key cylinder while the vehicle is in motion. The steering wheel is locked by removing the key.

ACC

LOCK

ON

START

C040A01E

o “START” The engine is started in this position. It will crank until you release the key.

NOTE: Do not hold the key in the “START” position for more than 15 seconds.

o “ON” When the key is in the “ON position, the ignition is on and all accessories may be turned on. If the engine is not running, the key should not be left in the “ON” position. This will discharge the battery and may also damage the ignition sys- tem.

o “ACC” With the key in the “ACC” position, some elec- trical accessories (radio etc.) may be operated.

o “LOCK” The key can be removed or inserted in this position. To protect against theft, the steering wheel locks by removing the key.

NOTE: To unlock the steering wheel, insert the key, and then turn the steering wheel and key simultaneously.

C050A01A-AAT STARTING

ACC

LOCK

ON

START

C070C01E

WARNING: Never run the engine in a closed or poorly ventilated area any longer than is needed to move your car in or out of the area. The carbon monoxide gas emitted is odorless and can cause serious injury or death.

DRIVING YOUR HYUNDAI

Insert key, and fasten the seat belt.

C050B01A-AAT Normal Conditions: The Starting Procedure: 1. 2. Depress the clutch pedal fully and place the gearshift lever (manual transaxle) in neutral or the selector lever (automatic transaxle) in "P" (park) position.

3. After turning the ignition key to the "ON" position, make certain all warning lights and gauges are functioning properly before start- ing the engine.

WARNING: Be sure that the clutch is fully depressed when starting a manual transaxle vehicle. Your manual transaxle equipped vehicle will not start unless the clutch pedal is fully depressed. On a manual transaxle equipped vehicle that can be started without depress- ing the clutch, there is the potential to cause damage to the vehicle or injury to someone inside or outside the vehicle as a result of the forward or backward movement of the vehicle that will occur if the clutch is not depressed when the vehicle is started.

4. Turn the ignition key to the "Start" position

and release it when the engine starts. After the engine has started, allow the en- gine to run for 10 to 20 seconds prior to placing the vehicle in gear.

The starter should not be operated for more than 15 seconds at a time. Wait 15-30 sec- onds between starting attempts to protect the starter from overheating.

C070C02A-AAT To Remove the Ignition Key

C050A01E

(If your vehicle is equipped with an automatic transaxle) 1. Turn the ignition key counterclockwise from the "ACC" position to the "LOCK" position. 2. The key can be removed in the "LOCK"

position.

(If your vehicle is equipped with a manual transaxle) 1. Turn the ignition key to the "ACC" position. 2. Simultaneously push and turn the ignition key counterclockwise from the "ACC" posi- tion to the "LOCK" position.

3. The key can be removed in the "LOCK"

position.

2- 3

DRIVING YOUR HYUNDAI

o If you've come to a complete stop and it's hard to shift into 1st or R(Reverse), put the shift lever in N(Neutral) position and release the clutch. Press the clutch pedal back down, and then shift into 1st or R(Reverse) gear position.

o Do not use the shift lever as a handrest during driving, as this can result in pre- mature wear of the transaxle shift forks.

CAUTION: When downshifting from fifth gear to fourth gear, caution should be taken not to inad- vertently press the gear shift lever sideways in such a manner that second gear is en- gaged. Such a drastic downshift may cause the engine speed to increase to the point that the tachometer will enter the red zone. Such over-revving of the engine may possi- bly cause engine damage.

C070B01A-AAT Using the Clutch The clutch should be pressed all the way to the floor before shifting, then released slowly. The clutch pedal should always be used after fully returning to the original position. Do not rest your foot on the clutch pedal while driving. This can cause unnecessary wear. Do not partially engage the clutch to hold the car on an incline. This causes unnecessary wear. Use the parking brake to hold the car on an incline. Do not operate the clutch pedal rapidly and repeatedly.

C070D02A-AAT Good Driving Practices o Never take the car out of gear and coast down a hill. This is extremely hazardous. Always leave the car in gear.

o Don't "ride" the brakes. This can cause them to overheat and malfunction. Instead, when you are driving down a long hill, slow down and shift to a lower gear. When you do this, engine braking will help slow the car. o Slow down before shifting to a lower gear. This will help avoid over-revving the engine, which can cause damage.

o Slow down when you encounter cross winds. This gives you much better control of your car.

C070A02GK-AAT OPERATING THE MANUAL TRANSAXLE

HGK181-E

Your Hyundai's manual transaxle has a con- ventional shift pattern. This shift pattern is im- printed on the shift knob. The transaxle is fully synchronized in all forward gears so shifting to either a higher or a lower gear is easily accom- plished.

NOTE: o To shift into reverse, rest the lever in neutral for at least 3 seconds after your car is completely stopped. Then move the lever into the reverse position.

o During cold weather, shifting may be dif- ficult until the transaxle lubricant has warmed up. This is normal and not harm- ful to the transaxle.

2- 4

o Be sure the car is completely stopped be- fore you attempt to shift into reverse. The transaxle can be damaged if you do not. To shift into reverse, depress the clutch, move the shift lever to neutral, wait three seconds, then shift to the reverse position.

o Exercise extreme caution when driving on a slippery surface. Be especially careful when braking, accelerating or shifting gears. On a slippery surface, an abrupt change in vehi- cle speed can cause the drive wheels to lose traction and the vehicle to go out of control.

WARNING: o The risk of rollover is greatly increased if you lose control of your vehicle at high- way speeds.

o Loss of control often occurs if two or more wheels drop off the roadway and the driver oversteers to reenter the road- way.

o In the event your vehicle leaves the road- way, do not steer sharply. Instead, slow down before pulling back into the travel lanes.

o In a collision crash, an unbelted person is significantly more likely to die than a person wearing a seatbelt.

DRIVING YOUR HYUNDAI

C070E02GK-AAT RECOMMENDED SHIFT POINTS The shift points as shown below are recom- mended for optimum fuel economy and perfor- mance.

Shift

from-to

1-2

2-3

3-4

4-5

Recommended

15 mph (20 km/h)

25 mph (40 km/h)

35 mph (55 km/h)

45 mph (75 km/h)

C090A03Y-AAT AUTOMATIC TRANSAXLE

The highly efficient Hyundai automatic transaxle has four forward speeds and one reverse speed. The individual speeds are selected automati- cally, depending on the position of the speed selector lever. The selector lever has 2 gates; the main gate and the manual gate.

NOTE: For information on manual gate operation, refer to "Sports Mode".

In the main gate, the selector lever has 4
positions, and is equipped with a button to avoid inadvertent wrong selection.

NOTE:

Depress the brake pedal and push the button when shifting. Push the button when shifting. The selector lever can be shifted freely.

The first few shifts on a new vehicle, or if the battery has been disconnected, may be somewhat abrupt. This is a normal condi- tion, and the shifting sequence will adjust after shifts are cycled a few times by the T.C.M (Transmission Control Module).

HGK174

2- 5

CAUTION: Never shift into "R" or "P" position while the vehicle is moving.

C090A02L

The indicator lights in the instrument cluster indicate the selector lever position when the ignition is switched "ON". During the sports mode operation, the gear currently in use dis- plays in the numeral indicator.

2- 6

DRIVING YOUR HYUNDAI

C090B01A-AAT The function of each position is as follows:

o P (Park): Use to hold the vehicle in place when parked or while starting the engine; shift the selector lever to the "P" (Park) position. Whenever parking the car, apply the parking brake and shift the selector lever to the "P" (Park) position.

CAUTION: Never place the selector lever in the "P" (Park) position unless the vehicle is fully stopped. Failure to observe this caution will cause severe damage to the transaxle.

C090C01A-AAT o R(Reverse): Use for backing up the vehicle. Bring the car to a complete stop before shifting the selector lever to "R" position.

C090D02O-AAT o N (Neutral): In the "N" position, the transaxle is in neutral, which means that no gears are engaged. The engine can be started with the shift lever in "N" position, although this is not recommended except if the engine stalls while the car is moving.

C090E01O-AAT o D(Drive): Use for normal driving. The transaxle will auto- matically shift through a four gear sequence.

C090F01GK-GAT Sports Mode

HGK175

Whether the vehicle is stationary or in motion, sports mode is selected by pushing the selector lever from the "D" position into the manual gate. To return to "D" range operation, push the selector lever back into the main gate. In sports mode, moving the selector lever back- wards and forwards can make rapid gearshifts simple. In contrast to a manual transaxle, the sports mode allows gearshifts with the accel- erator pedal depressed. UP (+) : Push the lever forward once to shift up one gear. DOWN (-) : Pull the lever backwards once to shift down one gear.

SKIP : By rapidly moving the selector forward or backward twice, it is possible to skip one gear, i.e. 1st to 3rd or 3rd to 1st .

CAUTION: o In sports mode, the driver must execute upward shifts in accordance with pre- vailing road conditions, taking care to keep the engine speed below the red zone.

o For engine protection, upward shifts are made automatically when the engine rpm reaches the red zone.

o By rapidly moving the selector lever back- wards (-) twice it is possible to skip one gear by using the sports mode. Since sudden engine braking and/or rapid ac- celeration can cause a loss of traction, however, downshifts must be made care- fully in accordance with the vehicle's speed.

NOTE: o In sports mode, only the four forward gears can be selected. To reverse or park the vehicle, move the selector lever to the "R" or "P" position as required.

o In sports mode, downward shifts are made automatically when the vehicle slows down. When the vehicle stops, 1st gear is automatically selected.

o To maintain the required levels of vehicle performance and safety, the system may not execute certain gearshifts when the selector lever is operated.

DRIVING YOUR HYUNDAI

o Before driving away from a stop on a slippery road, push the selector lever forward into the +(UP) position. This causes the transaxle to shift into 2nd gear which is better for smooth driving away on a slippery road. Push the selec- tor lever to the -(DOWN) side to shift back to 1st gear.

C090H01L-GAT NOTE: o For smooth and safe operation, depress the brake pedal when shifting from “Neu- tral” position or “Park” position to a forward or reverse gear.

o The ignition key must be in the “ON” position and the brake pedal fully de- pressed in order to move the shift lever from the “P” (Park) position to any of the other positions.

o It is always possible to shift from “R”, “N”, “D” position to “P” position. The vehicle must be fully stopped to avoid transaxle damage.

C090I02L-GAT CAUTION: o Shift into “R” and “P” position only when

the vehicle has completely stopped.

o Do not accelerate the engine in reverse or any of the forward positions with the brakes applied.

o Always apply the footbrake when shift- ing from “P” or “N”, to “R”, “D”position.

o Do not use the “P” (Park) position in place of the parking brake. Always set the parking brake, shift the transaxle into “P” (Park) position and turn off the igni- tion when you leave the vehicle, even momentarily. Never leave the vehicle unattended while the engine is running. o Check the automatic transaxle fluid level

regularly, and add fluid as necessary.

o See the maintenance schedule for the

proper fluid recommendation.

C090N01O-AAT Good Driving Practices o Never move the gear selector lever from “P” or “N” to any other position with the acceler- ator pedal depressed.

o Never move the gear selector lever into “P”

when the vehicle is in motion.

o Be sure the car is completely stopped be-

fore you attempt to shift into “R”.

o Never take the car out of gear and coast down a hill. This may be extremely hazard- ous. Always leave the car in gear when moving.

o Do not “ride” the brakes. This can cause them to overheat and malfunction. Instead, when you are driving down a long hill, slow down and shift to a lower gear. When you do this, engine braking will help slow the car. o Slow down before shifting to a lower gear. Otherwise, the lower gear may not be en- gaged.

2- 7

o Always use the parking brake. Do not de- pend on placing the transaxle in “P” to keep the car from moving.

o Exercise extreme caution when driving on a slippery surface. Be especially careful when braking, accelerating or shifting gears. On a slippery surface, an abrupt change in vehi- cle speed can cause the drive wheels to lose traction and the vehicle to go out of control.

WARNING: o Avoid high cornering speeds. o Do not make quick steering wheel move- ments, such as sharp lane changes or fast, sharp turns.

o Always wear your seat belts. o The risk of rollover is greatly increased if you lose control of your vehicle at high- way speeds.

o Loss of control often occurs if two or more wheels drop off the roadway and the driver oversteers to reenter the road- way.

o In the event your vehicle leaves the road- way, do not steer sharply. Instead, slow down before pulling back into the travel lanes.

o In a collision crash, un unbelted person is significantly more likely to die than a person wearing a seatbelt.

2- 8

DRIVING YOUR HYUNDAI

C130A01A-AAT GOOD BRAKING PRACTICES WARNING: Nothing should be carried on top of the shelf panel behind the rear seat. If there were an accident or a sudden stop, such objects could move forward and cause dam- age to the vehicle or injure the occupants.

o After being parked, check to be sure the parking brake is not engaged and that the parking brake indicator light is out before driving away.

o Driving through water may get the brakes wet. They can also get wet when the car is washed. Wet brakes can be dangerous! Your car will not stop as quickly if the brakes are wet. Wet brakes cause the car to pull to one side. To dry the brakes, apply the brakes lightly until the braking action returns to normal, taking care to keep the car under control at all times. If the braking action does not return to normal, stop as soon as it is safe to do so and call your Hyundai dealer for assistance.

o Don’t coast down hills with the car out of gear. This is extremely hazardous. Keep the car in gear at all times, use the brakes to slow down, then shift to a lower gear so that engine braking will help you maintain a safe speed.

o Don’t “ride” the brake pedal. Resting your foot on the brake pedal while driving can be dangerous because it can result in the brakes overheating and losing their effectiveness. It also increases the wear of the brake compo- nents.

o If a tire goes flat while you are driving, apply the brakes gently and keep the car pointed straight ahead while you slow down. When you are moving slowly enough for it to be safe to do so, pull off the road and stop in a safe place.

o If your car is equipped with an automatic transaxle, don’t let your car creep forward. To avoid creeping forward, keep your foot on the brake pedal when the car is stopped. o Use caution when parking on a hill. Engage the parking brake and place the gear selec- tor lever in “P” (automatic transaxle) or in first or reverse gear (manual transaxle). If your car is facing downhill, turn the front wheels into the curb to help keep the car from rolling. If your car is facing uphill, turn the front wheels away from the curb to help keep the car from rolling. If there is no curb or if it is required by other conditions to keep the car from rolling, block the wheels.

o Under some conditions your parking brake can freeze in the engaged position. This is most likely to happen when there is an accumulation of snow or ice around or near the rear brakes or if the brakes are wet. If there is a risk that the parking brake may freeze, apply it only temporarily while you

put the gear selector lever in “P” (automatic) or in first or reverse gear (manual transaxle) and block the rear wheels so the car cannot roll. Then release the parking brake.

o Do not hold the vehicle on the upgrade with the accelerator pedal. This can cause the transmission to overheat. Always use the brake pedal or parking brake.

C120A02A-AAT ANTI-LOCK BRAKE SYSTEM (If installed) The Anti-Lock Brake System (ABS) is designed to prevent wheel lock-up during sudden braking or on hazardous road surfaces. The ABS con- trol module monitors the wheel speed and con- trols the pressure applied to each brake. Thus, in emergency situations or on slick roads, ABS will increase vehicle control during braking.

NOTE: During ABS operation, a slight pulsation may be felt in the brake pedal when the brakes are applied. Also, a noise may be heard in the engine compartment while brak- ing. These conditions are normal and indi- cate that the anti-lock brake system is func- tioning properly.

DRIVING YOUR HYUNDAI

WARNING: ABS will not prevent accidents due to im- proper or dangerous driving maneuvers. Even though vehicle control is improved during emergency braking, always maintain a safe distance between you and objects ahead. Vehicle speeds should always be reduced during extreme road conditions. The braking distance for cars equipped with an anti-lock braking system may be longer than for those without it in the following road conditions.

o Driving on rough, gravel or snow-cov-

ered roads.

o Driving with tire chains installed. o Driving on roads where the road surface is pitted or has different surface height.

During these conditions the vehicle should be driven at reduced speeds. The safety features of an ABS equipped vehicle should not be tested by high speed driving or cor- nering. This could endanger the safety of yourself or others.

C300A03Y-GAT TRACTION CONTROL SYSTEM (TCS) (If installed)

HGK156A

On slippery road surfaces, the traction control system (TCS) limits the drive wheels from spin- ning excessively, thus helping the car to accel- erate. It also provides sufficient driving force and steering performance as the car turns at accelerated speeds.

SLIP Control Limits the drive wheels from spinning exces- sively during starting or while making accelerat- ed turns on slippery roads to avoid losing the driving force of the front wheels.

Driving hints TCS does not actively apply brakes. Be sure to decelerate the car sufficiently before entering curves.

2- 9

CAUTION: