Press to pop the knob out. To increase the bass, rotate the knob clockwise, while to decrease the bass, rotate the knob counterclockwise.
BALANCE Control
Further pull the popped-up knob. Rotate the knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counterclock- wise, left speaker sound will be emphasized (right speaker sound will be attenuated).
3. TREBLE/FAD Knob TREBLE Control Knob
Press to pop the knob out and turn to the left or right for the desired treble tone.
FAD (Fader Control) Knob
Further pull the popped-up knob. Turn the control knob clockwise to emphasize rear speaker sound (front speaker sound will be attenuated). When the control knob is turned counterclockwise, front speaker sound will be emphasized (rear speaker sound will be attenu- ated).
4. TUNE / SEEK Select Button TUNE (Manual) Select Button
Press the (+) side or (-) side to increase or to decrease the frequency. With the button held down for 0.5 sec. or more, the frequency selec- tion will increase or decrease rapidly.
SEEK Operation (Automatic Channel Selection)
Press the TUNE select button 1 sec. or more. When the (+) side is pressed, the unit will automatically tune to the next higher frequency and when the (-) side is pressed, it will automati- cally tune to the next lower frequency.
FEATURES OF YOUR HYUNDAI
107
5. PRESET STATION Select Buttons
Six (6) stations for AM, FM and FM2 respec- tively can be preset in the electronic memory circuit.
HOW TO PRESET STATIONS
Six AM and twelve FM stations may be pro- grammed into the memory of the radio. Then, by simply pressing the band select button and/or one of the six station select buttons, you may recall any of these stations instantly. To pro- gram the stations, follow these steps:
o Press band selector to set the band for AM,
FM and FM2.
o Select the desired station to be stored by
seek, scan or manual tuning.
o Determine the preset station select button
you wish to use to access that station.
o Press the station select button for more than two seconds. A select button indicator will show in the display indicating which select button you have depressed. The frequency display will flash after it has been stored into the memory. You should then release the button, and proceed to program the next desired station. A total of 18 stations can be programmed by selecting one AM and two FM station per button.
o When completed, any preset station may be recalled by selecting AM, FM or FM2 band and the appropriate station button.
xgflhma-1.p65
107
6/16/04, 3:05 PM
1FEATURES OF YOUR HYUNDAI
108
6. BAND Selector
Pressing the button changes the AM, FM1 and FM2 bands. The mode selected is shown on the display.
7. EQ Button
Press the EQ button to select the CLASSIC, JAZZ, ROCK and DEFEAT MODE for the desired tone quality. Each press of the button changes the display as follows;
CLASSIC → JAZZ → ROCK → DEFEAT
↑
CAUTION:
o Do not place beverages close to the audio system. The audio system mecha- nism may be damaged if you spill them. o Do not impact on the audio system, or the audio system mechanism could be damaged.
xgflhma-1.p65
108
6/16/04, 3:05 PM
B940Q01L-AAT COMPACT DISC PLAYER OPERATION (H940C) (If Installed)
FEATURES OF YOUR HYUNDAI
109
5. EQ Button
6. EJECT Button
1. Playing CD
3. TRACK UP/DOWN
xgflhma-1.p65
109
6/16/04, 3:05 PM
4. REPEAT
2. FF/REW Button
H940O01L
1FEATURES OF YOUR HYUNDAI
110
B940R02L-AAT 1. Playing CD
o Insert the CD with the label facing upward. o Insert the CD to start CD playback, during
radio operation or cassette tape playing.
o When a disc is in the CD deck, if you press the CD button, the CD player will begin playing even if the radio or cassette player is being used.
o The CD player can be used when the ignition switch is in either the "ON" or "ACC" position.
2. FF/REW
While the disc is playing, if you hold down the FF button continuously, the selected track is ad- vanced. Holding down the REW button continu- ously moves the selected track back.
4. REPEAT
o To repeat the track you are currently listen- ing to, press the RPT button. To cancel, press again.
o If you do not release RPT operation after all the tracks are played back, the unit will play back again from the first track.
5. EQ Button
Press the EQ button to select the CLASSIC, JAZZ, ROCK and DEFEAT MODE for the desired tone quality. Each press of the button changes the display as follows;
CLASSIC → JAZZ → ROCK → DEFEAT
↑
3. TRACK UP/DOWN
6. EJECT Button
o The desired track on the disc currently being played can be selected using the track number.
o Press once to skip forward to the beginn-
ing of the next track.
o Press once to skip back to the beginning
of the track.
When the EJECT button is pressed with a CD loaded, CD will eject.
NOTE: o To assure proper operation of the unit, keep the vehicle interior temperature within a normal range by using the vehicle's air conditioning or heating sys- tem.
o When replacing the fuse, replace it with
a fuse having the correct capacity.
o The preset station frequencies are all erased when the car battery is discon- nected. Therefore, all data will have to be set again if this should occur.
o Do not add any oil to the rotating parts. Keep magnets, screwdrivers and other metallic objects away from the tape mechanism and head.
o This equipment is designed to be used only in a 12 volt DC battery system with negative ground.
o This unit is made of precision parts. Do not attempt to disassemble or adjust any parts.
o When driving your vehicle, be sure to keep the volume of the unit set low enough to allow you to hear sounds coming from the outside.
o Do not expose this equipment (includ- ing the speakers and tape) to water or excessive moisture.
xgflhma-1.p65
110
6/16/04, 3:05 PM
FEATURES OF YOUR HYUNDAI
111
CAUTION:
o Do not insert warped or poor quality discs into the CD player as damage to the unit may occur.
o Do not insert anything like coins into the player slot as damage to the unit may occur.
o Do not place beverages close to the audio system. The playback mechanism may be damaged if you spill them.
o Do not impact on the audio system, or the playback mechanism could be dam- aged.
o Driving on the off-roads or other vibra-
tions may skip your compact disc. Do not use the audio system on off- roads as the discs could be scratched and damaged.
o Do not grip or pull out the disc with your hand while the disc is being pulled into the unit by the self loading mechanism. These can cause poor disc scratching to occur or trouble in the compact disc player.
o Avoid using CD-Recordable or CD- Rewritable as the player could not be operated in recording way of the CD maker. When using the compact disc player, genuine CDs are recommended.
xgflhma-1.p65
111
6/16/04, 3:05 PM
1FEATURES OF YOUR HYUNDAI
112
B940S01L-AAT CD AUTO CHANGER (H940C) (If Installed)
4. DISC Select Button
6. EQ Button
1. CDCHG Button
3. TRACK UP/DOWN
2. FF/REW
5. REPEAT
H940O01L
xgflhma-1.p65
112
6/16/04, 3:05 PM
B940T02L-AAT The CD auto changer is located in the left side of the trunk.
o To use the CD auto changer
1. Open the sliding lid of the CD auto changer. 2. To eject the compact disc magazine, press the EJECT button located in the CD auto changer. Insert the discs into the magazine.
3. 4. Push the magazine into the CD auto changer
and close the sliding lid.
o The CD auto changer can be used when the ignition switch is in either "ON" or "ACC" position.
1. CDCHG Button
When the CD changer magazine contains discs, press the CDCHG button and the CD changer can be used even if the radio is being used. The Hyundai CD changer can hold up to eight discs. The disc number will be lit, and the track number, and elapsed time will be displayed.
FEATURES OF YOUR HYUNDAI
113
2. FF/REW While the disc is playing, if you hold down the FF button continuously, the selected track is ad- vanced. Holding down the REW button continu- ously moves the selected track back.
6. EQ Button
Press the EQ button to select the CLASSIC, JAZZ, ROCK and DEFEAT MODE for the desired tone quality. Each press of the button changes the display as follows;
3. TRACK UP/DOWN
o The desired track on the disc currently being played can be selected using the track number.
o Press once to skip forward to the beginn-
ing of the next track.
o Press once to skip back to the beginning
of the track.
4. DISC Select Button
To select the CD you want, push "DISC +" or "DISC-" to change the disc number.
5. REPEAT
o To repeat the track you are listening to, press the RPT button. To cancel, press again.
o If you do not release RPT operation after all the tracks are played back, the unit will play back again from the first track.
CLASSIC → JAZZ → ROCK → DEFEAT
↑
NOTE: o When replacing the fuse, replace it with
a fuse having the correct capacity.
o This equipment is designed to be used only in a 12 volt DC battery system with negative ground.
o This unit is made of precision parts. Do not attempt to disassemble or adjust any parts.
o When driving your vehicle, be sure to keep the volume of the unit set low enough to allow you to hear sounds coming from the outside.
xgflhma-1.p65
113
6/16/04, 3:05 PM
1FEATURES OF YOUR HYUNDAI
114
CAUTION:
o Do not insert warped or poor quality discs into the CD changer as damage to the unit may occur.
o Do not insert anything like coins into the changer slot as damage to the unit may occur.
o Do not place beverages close to the audio system. The playback mechanism may be damaged if you spill them.
o Do not impact on the audio system, or the playback mechanism could be dam- aged.
o Driving on the off-roads or other vibra-
tions may skip your compact disc. Do not use the audio system on off- roads as the discs could be scratched and damaged.
o Do not grip or pull out the disc with your hand while the disc is being pulled into the unit by the self loading mechanism. These can cause poor disc scratching to occur or trouble in the compact disc player.
o Avoid using CD-Recordable or CD- Rewritable as the player could not be operated in recording way of the CD maker. When using the compact disc player, genuine CDs are recommended.
xgflhma-1.p65
114
6/16/04, 3:05 PM
AUDIO FAULT CODE
FEATURES OF YOUR HYUNDAI
115
B890A01Y-AAT If you see any error indication in the display while using the system in the CD or Tape mode, find the cause in the chart below. If you cannot clear the error indication, take the car to your Hyundai dealer.
INDICATION
CAUSE
SOLUTION
Er2
Er3
Er6
Er8
CD DECK MECHANICAL ERROR
After resetting the audio system, push the eject button.
(EJECT ERROR, LOADING ERROR)
If disc is not ejected, consult your hyundai dealer.
FOCUS ERROR
DATA READ ERROR
DISC ERROR
TAPE DECK ERROR
TAPE EJECT ERROR
Make sure the disc is not scratched or damaged.
Press the eject button and pull out the disc.
Then insert a normal cd disc.
Check if the disc is inserted correctly in the cd player.
Make sure the disc is not scratched or damaged.
After resetting the audio system, push the eject button.
If tape does not eject, consult your Hyundai dealer.
HHH
TEMPERATURE IS TOO HIGH
Fault code will reset automatically when the temperature returns to normal.
no CD
NO DISC IN MAGAZINE
NO CD MAGAZINE IN THE AUTO CHANGER
Insert disc in magazine or insert cd magazine in the auto changer.
xgflhma-1.p65
115
6/16/04, 3:05 PM
1FEATURES OF YOUR HYUNDAI
116
CARE OF DISC
B850A02F-AAT Proper Handling
CARE OF CASSETTE TAPES
Storage
B860A01A-AAT
When not in use, place your discs in their individual case and store them in a cool place away from the sun, heat, and dust. Do not grip or pull out the disc with your hand while the disc is being pulled into the unit by the self loading mechanism.
Keep Your Discs Clean
B850A01L Handle your disc as shown. Do not drop the disc. Hold the disc so you will not leave finger- prints on the surface. If the surface is scratched, it may cause the pickup to skip signal tracks. Do not affix tape, paper, or gummed labels on the disc. Do not write on the disc.
Damaged Disc
Do not attempt to play damaged, warped or cracked discs. These could severely damage the playback mechanism.
B850A02L Fingerprints, dust, or soil on the surface of a disc could cause the pickup to skip signal tracks. Wipe the surface clean with a clean soft cloth. If the surface is heavily soiled, dampen a clean soft cloth in a solution of mild neutral detergent to wipe it clean.
B860A01L Proper care of your cassette tapes will extend the tape life and increase your listening enjoy- ment. Always protect your tapes and cassette cases from direct sunlight, severely cold and dusty conditions. When not in use, cassettes should always be stored in the original protec- tive cassette case. When the vehicle is very hot or cold, allow the interior temperature to become more comfortable before listening to your cas- settes.
xgflhma-1.p65
116
6/16/04, 3:05 PM
FEATURES OF YOUR HYUNDAI
117
o Never leave a cassette inserted in the player when not being played. This could damage the tape player unit and the cassette tape. o We strongly recommend against the use of tapes longer than C-60 (60 minutes total). Tapes such as C-120 or C-180 are very thin and do not perform as well in the automotive environment.
o Store cassettes in a cool, dry place with the open side facing down to prevent dust from setting in the cassette body.
o Avoid repeated fast reverse usage to replay one given tune or tape section. This can cause poor tape winding to occur, and even- tually cause excessive internal drag and poor audio quality in the cassette. If this occurs, it can sometimes be corrected by fast winding the tape from end to end several times. If this does not correct the problem, do not continue to use the tape in your vehicle.
o The playback head, capstan and pinch roll- ers will develop a coating of tape residue that can result in deterioration of sound quality, such as a wavering sound. They should be cleaned monthly using a commercially avail- able head cleaning tape or special solution available from audio specialty shops. Follow the supplier's directions carefully and never oil any part of the tape player unit.
o Always be sure that the tape is tightly wound on its reel before inserting in the player. Rotate a pencil in the drive sprockets to wind up any slack.
Head
B860B02L o Be sure that the cassette label is not loose or peeling off or tape ejection may be difficult. o Never touch or soil the actual audio tape
surfaces.
o Keep all magnetized objects, such as elec- tric motors, speakers or transformers away from your cassette tapes and tape player unit.
Cotton applicator
B860A02L
B860A03L
xgflhma-1.p65
117
6/16/04, 3:05 PM
1FEATURES OF YOUR HYUNDAI
118
NOTE: Look at a tape before you insert it. If the tape is loose, tighten it by turning one of the hubs with a pencil or your finger. If the label is peeling off, do not put it in the drive mechanism. Do not leave tapes sitting where they are exposed to hot, warm, or high humidity, such as on top of the dashboard or in the player. If a tape is exposed to excessively hot or cold, let it reach a moderate temperature before putting it in the player.
GLASS ANTENNA
B870D02Y-GAT
RADIO "ON"
B870D03L
When the radio power switch is turned on while the ignition key is in either the "ON" or "ACC" position, your car will receive both AM and FM broadcast signals through the antenna in the rear window glass.
CAUTION:
o Do not clean the inner side of the rear window glass with an abrasive type of glass cleaner or use a scraper to remove foreign deposits from the inner surface of the glass as this may cause damage to the antenna elements.
o Avoid adding metallic coating (Some aftermarket window tinting has metallic contents). These can disturb receiving AM and FM broadcast signals.
xgflhma-1.p65
118
6/16/04, 3:05 PM
DRIVING YOUR HYUNDAI
Before Starting the Engine ............................................ 2-3
Key Positions ................................................................ 2-3
Starting .......................................................................... 2-4
Automatic Transaxle ..................................................... 2-5
Anti-Lock Brake System (ABS) .................................... 2-8
Traction Control System (TCS) .................................... 2-9
Good Braking Practices .............................................. 2-10
Driving for Economy ................................................... 2-11
Winter Driving ............................................................. 2-13
Trailer or Vehicle Towing ............................................ 2-15
Vehicle Load Limit ....................................................... 2-19
xgflhma-2.p65
6/16/04, 3:00 PM
2 DRIVING YOUR HYUNDAI
WARNING: ENGINE EXHAUST CAN BE DANGEROUS!
C010A02L-AAT Engine exhaust fumes can be extremely dangerous. If, at any time, you smell exhaust fumes inside the vehicle, open the windows immediately. o Do not inhale exhaust fumes. Exhaust fumes contain carbon monoxide, a colorless, odorless gas that can cause unconsciousness and death by asphyxiation. o Be sure the exhaust system does not leak. The exhaust system should be checked whenever the vehicle is raised to change the oil or for any other purpose. If you hear a change in the sound of the exhaust or if you drive over something that strikes the underneath side of the car, have the exhaust system checked as soon as possible by your Hyundai dealer. o Do not run the engine in an enclosed area. Letting the engine idle in your garage, even with the garage door open, is a hazardous practice. Never run the engine in your garage any longer than it takes to start the engine and back the car out. o Avoid idling the engine for prolonged periods with people inside the car. If it is necessary to idle the engine for a prolonged period with people inside the car, be sure to do so only in an open area with the air intake set at "Fresh" and fan operating at one of the higher speeds so fresh air is drawn into the interior. If you must drive with the trunk open because you are carrying objects that make this necessary: 1. Close all windows. 2. Open side vents. 3. Set the air intake control at "Fresh", the air flow control at "Floor" or "Face" and the fan at one of the higher speeds. To assure proper operation of the ventilation system, be sure the ventilation air intakes located just in front of the windshield are kept clear of snow, ice, leaves or other obstructions.
PROPOSITION 65 WARNING:
Engine exhaust and a wide variety of automobile components and parts, including components found in the interior furnishings in a vehicle, contain or emit chemicals known to the State of California to cause cancer and birth defects and reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
xgflhma-2.p65
6/16/04, 3:00 PM
BEFORE STARTING THE ENGINE
COMBINATION IGNITION SWITCH
KEY POSITIONS
DRIVING YOUR HYUNDAI
C020A01A-AAT Before you start the engine, you should always:
C030A01L-AAT To Start the Engine
1. Look around the vehicle to be sure there are no flat tires, puddles of oil, water or other indications of possible trouble.
2. After entering the car, check to be sure the
parking brake is engaged.
3. Check that all windows, and lights are clean. 4. Check that the interior and exterior mirrors
are clean and in position.
5. Check your seat, seatback and headrest to be sure they are in their proper positions.
6. Lock all the doors. 7. Fasten your seat belt and be sure that all
other occupants have fastened theirs.
8. Turn off all lights and accessories that are
not needed.
9. When you turn the ignition switch to "ON", check that all appropriate warning lights are operating and that you have sufficient fuel. 10.Check the operation of warning lights and all
bulbs when key is in the "ON" position.
o Place the shift lever in "P" (park) and de-
press the brake pedal fully.
o To start the engine, insert the ignition key and
turn it to the "START" position. Release it as
soon as the engine starts. Do not hold the
key in the "START" position for more than 15
seconds.
C040A01A-AAT
WARNING:
The engine should not be turned off or the key removed from the ignition key cylinder while the vehicle is in motion. The steering wheel is locked by removing the key.
NOTE: o For safety, the engine will not start if the shift lever is not in "P" or "N" Position. o The ignition key cannot be turned from "ACC" position to "LOCK" position un- less the shift lever is in the "P" (Park) position or the negative battery terminal is disconnected from the battery. To remove the key, always confirm that the shift lever is securely positioned in "P" (Park).
o For additional information about start-
ing, see page 2-4.
ACC
LOCK
ON
START
C040A01E-1
o "START" The engine is started in this position. It will crank until you release the key.
NOTE: Do not hold the key in the "START" position for more than 15 seconds.
xgflhma-2.p65
6/16/04, 3:00 PM
2 DRIVING YOUR HYUNDAI
o "ON" When the key is in the "ON" position, the ignition is on and all accessories may be turned on. If the engine is not running, the key should not be left in the "ON" position. This will discharge the battery and may also damage the ignition sys- tem.
o "ACC" With the key in the "ACC" position, some elec- trical accessories (radio, etc.) may be oper- ated.
o "LOCK" The key can be removed or inserted in this position. To protect against theft, the steering wheel locks by removing the key.
NOTE: To unlock the steering wheel, insert the key, and then turn the steering wheel and key simultaneously.
C070C02A-AAT To remove the ignition key
ACC
LOCK
ON
START
C070C01E-1
1. Turn the ignition key to the "ACC" position.
2. Turn the ignition key counterclockwise from
the "ACC" position to the "LOCK" position.
3. The key can be removed in the "LOCK"
position.
STARTING
C050A01A-AAT
C050A01E-1
WARNING:
Never run the engine in a closed or poorly ventilated area any longer than is needed to move your car in or out of the area. The carbon monoxide gas emitted is odorless and can cause serious injury or death.
xgflhma-2.p65
6/16/04, 3:00 PM
C050B01L-AAT Normal Conditions: The Starting Procedure:
AUTOMATIC TRANSAXLE
C090A02L-AAT
Insert key, and fasten the seat belt.
1. 2. Depress the brake pedal fully and place the
selector lever in "P" (park) position.
3. After turning the ignition key to the "ON" position, make certain all warning lights and gauges are functioning properly before start- ing the engine.
4. Turn the ignition key to the "Start" position
and release it when the engine starts. After the engine has started, allow the engine to run for 10 to 20 seconds prior to placing the vehicle in gear. The starter should not be operated for more than 15 seconds at a time. Wait 15-30 sec- onds between starting attempts to protect the starter from overheating.
HXG065
The highly efficient Hyundai automatic transaxle
has five forward speeds and one reverse speed.
The individual speeds are selected automati-
cally, depending on the position of the speed
selector lever. The selector lever has 2 gates;
the main gate and the manual gate.
NOTE:
For information on manual gate operation,
refer to "Sports Mode".
In the main gate, the selector lever has 5
positions, and is equipped with a button to avoid
inadvertent wrong selection.
DRIVING YOUR HYUNDAI
NOTE:
Depress the brake pedal and push the button when shifting. Push the button when shifting. The selector lever can be shifted freely.
The first few shifts on a new vehicle, or if the battery has been disconnected may be somewhat abrupt. This is a normal condi- tion, and the shifting sequence will adjust after shifts are cycled a few times by the T.C.M (Transaxle Control Module).
C090A02L
xgflhma-2.p65
6/16/04, 3:00 PM
2 DRIVING YOUR HYUNDAI
CAUTION:
Never shift into "R" or "P" position while the vehicle is moving.
C090C01A-AAT o R(Reverse):
C090F02L-AAT Sports Mode
Use for backing up the vehicle. Bring the car to a complete stop before shifting the selector lever to "R" position.
The indicator lights in the instrument cluster indicate the selector lever position when the ignition is switched "ON". During sports mode operation, green lights indicate the gear cur- rently in use.
C090B01A-AAT The function of each position is as fol- lows:
o P (Park):
Use to hold the vehicle in place when parked or while starting the engine. Whenever parking the car, apply the parking brake and shift the selec- tor lever to the "P" (Park) position.
C090D02A-AAT o N (Neutral):
In the "N" position, the transaxle is in neutral, which means that no gears are engaged. The engine can be started with the shift lever in "N" position, although this is not recommended except if the engine stalls while the car is moving.
C090E01L-AAT o D (Drive):
Use for normal driving. This position is used for most city and highway driving, for starting from a full stop to maximum speed. The transaxle will automatically shift through a five gear sequence.
CAUTION:
Never place the selector lever in the "P" (Park) position unless the vehicle is fully stopped. Failure to observe this caution will cause severe damage to the transaxle.
HXG200
Whether the vehicle is stationary or in motion, sports mode is selected by pushing the selector lever from the "D" position into the manual gate. To return to "D" range operation, push the selector lever back into the main gate. In sports mode, moving the selector lever back- wards and forwards can make rapid gearshifts simple. In contrast to a manual transaxle, the sports mode allows gearshifts with the accel- erator pedal depressed.
UP (+)
: Push the lever forward once to shift up one gear.
DOWN (-) : Pull the lever backward once to
shift down one gear.
xgflhma-2.p65
6/16/04, 3:00 PM
DRIVING YOUR HYUNDAI
C090I02L-GAT
CAUTION:
o Shift into "R" and "P" position only when
the vehicle has completely stopped.
o Do not accelerate the engine in reverse or any of the forward positions with the brakes applied.
o Always apply the footbrake when shift- ing from "P" or "N", to "R" or "D" posi- tion.
o Do not use the "P" (Park) position in place of the parking brake. Always set the parking brake, shift the transaxle into "P" (Park) position and turn off the ignition when you leave the vehicle, even momentarily. Never leave the vehicle unattended while the engine is running. o Check the automatic transaxle fluid level
regularly, and add fluid as necessary.
o See the maintenance schedule for the
proper fluid recomendation.
o Before driving away from a stop on a slippery road, push the selector lever forward into the +(UP) position. This causes the transaxle to shift into 2nd gear which is better for smooth driving away on a slippery road. Push the selec- tor lever to the -(DOWN) side to shift back to 1st gear.
C090H01L-GAT NOTE: o For smooth and safe operation, depress the brake pedal when shifting from "Neu- tral" position or "Park" position to a forward or reverse gear.
o The ignition key must be in the "ON" position and the brake pedal fully de- pressed in order to move the shift lever from the "P" (Park) position to any of the other positions.
o It is always possible to shift from "R", "N", "D" position to "P" position. The vehicle must be fully stopped to avoid transaxle damage.
CAUTION:
o In sports mode the driver must execute shifts in accordance with prevailing road conditions, taking care to keep the en- gine speed below the red zone. For the engine protection, upward shifts are made automatically when the engine rpm reaches the red zone.
o By rapidly moving the selector lever backwards (-) twice, it is possible to skip one gear, i.e., 3rd to 1st, 4th to 2nd or 5th to 3rd. Since sudden engine braking and/or rapid acceleration can cause a loss of traction, however, downshifts must be made carefully in accordance with the vehicle's speed.
NOTE: o In sports mode, only the five forward gears can be selected. To reverse or park the vehicle, move the selector lever to the "R" or "P" position as required.
o In sports mode, downward shifts are made automatically when the vehicle slows down. When the vehicle stops, 1st gear is automatically selected.
o To maintain the required levels of ve- hicle performance and safety, the sys- tem may not execute certain gearshifts when the selector lever is operated.
xgflhma-2.p65
6/16/04, 3:00 PM
2 DRIVING YOUR HYUNDAI
GOOD DRIVING PRACTICES
C090N03Y-AAT o Never move the gear selector lever from "P" or "N" to any other position with the accelera- tor pedal depressed.
o Never move the gear selector lever into "P"
when the vehicle is in motion.
o Be sure the car is completely stopped before
you attempt to shift into "R".
o Never take the car out of gear and coast down a hill. This may be extremely hazard- ous. Always leave the car in gear when moving.
o Do not "ride" the brakes. This can cause them to overheat and malfunction. Instead, when you are driving down a long hill, slow down and shift to a lower gear. When you do this, engine braking will help slow the car. o Slow down before shifting to a lower gear. Otherwise, the lower gear may not be en- gaged.
o Always use the parking brake. Do not de- pend on placing the transaxle in "P" to keep the car from moving.
o Exercise extreme caution when driving on a slippery surface. Be especially careful when braking, accelerating or shifting gears. On a slippery surface, an abrupt change in ve- hicle speed can cause the drive wheels to lose traction and the vehicle to go out of control.
ANTI-LOCK BRAKE SYSTEM
C120A02A-AAT (If Installed)
The Anti-Lock Brake System (ABS) is designed to prevent wheel lock-up during sudden braking or on hazardous road surfaces. The ABS con- trol module monitors the wheel speed and con- trols the pressure applied to each brake. Thus, in emergency situations or on slick roads, ABS will increase vehicle control during braking.
NOTE: During ABS operation, a pulsation may be felt in the brake pedal when the brakes are applied. Also, a noise may be heard in the engine compartment while braking. These conditions are normal and indicate that the anti-lock brake system is functioning prop- erly.
WARNING:
o The risk of rollover is greatly increased if you lose control of your vehicle at high- way speeds.
o Loss of control often occurs if two or more wheels drop off the roadway and the driver oversteers to reenter the road- way.
o In the event your vehicle leaves the road- way, do not steer sharply. Instead, slow down before pulling back into the travel lanes.
o In a collision crash, an unbelted person is significantly more likely to die than a person wearing a seatbelt.
o Never exceed posted speed limits. o Excessive depressing of the accelerater pedal in slippery driving conditions such as pulling out of deep snow or mud may cause severe damage to the transaxle. Rocking the vehicle is not recommended. Rather, use an appropriate towing method.
xgflhma-2.p65
6/16/04, 3:00 PM
!
WARNING:
Your ABS will not prevent accidents due to improper or dangerous driving maneuvers. Even though vehicle control is improved during emergency braking, always main- tain a safe distance between you and ob- jects ahead. Vehicle speeds should always be reduced during extreme road condi- tions. The braking distance for cars equipped with an anti-lock braking system may be longer than for those without it in the following road conditions. During these conditions the vehicle should be driven at reduced speeds.
o Rough, gravel or snow-covered roads. o With tire chains installed. o On roads where the road surface is pit-
ted or has different surface height.
The safety features of an ABS equipped vehicle should not be tested by high speed driving or cornering. This could endanger the safety of yourself or others.
TRACTION CONTROL SYSTEM (TCS)
C300A02Y-GAT (If Installed)
DRIVING YOUR HYUNDAI
Driving hints
TCS does not actively apply brakes. Be sure to decelerate the car sufficiently before entering curves.
CAUTION:
When the TCS indicator blinks, SLIP control has been activated. It also means that the road is slippery or your car is accelerating excessively. In this situation, gently release foot pressure from the accelerator pedal and maintain moderate speed.
WARNING:
Traction control is only a driving aid; all normal precautions for driving in inclement weather and on slippery driving surfaces should be observed.
C300A02L-A On slippery road surfaces, the traction control system (TCS) limits the drive wheels from spinning excessively, thus helping the car to accelerate. It also provides sufficient driving force and steering performance as the car turns at accelerated speeds.
SLIP Control
Limits the drive wheels from spinning exces- sively during starting or while making acceler- ated turns on slippery roads to avoid losing the driving force of the front wheels.
xgflhma-2.p65
6/16/04, 3:00 PM
2 DRIVING YOUR HYUNDAI
10
C300B01L-GAT TCS ON/OFF Mode
C300D02L-GAT Indicators and Warning
C130A01O-BAT GOOD BRAKING PRACTICES
In the TCS ON mode, the indicator in the instrument cluster will not be illuminated. To switch the TCS OFF mode, press the TCS switch . The SLIP control will be deactivated and the TCS indicator in the instrument cluster will be illuminated.
NOTE: 1) The TCS mode will automatically be turned ON after the engine is turned off and restarted.
2) When the traction control is operating properly, you can feel a slight pulsation in the vehicle. This is only the effect of brake control and indicates nothing unusual.
3) When the engine starts, a click is heard from the engine compartment; however, this is only the sound of traction control being checked.
4) When moving out of the mud or fresh snow, pressing the accelerator pedal may not cause the engine speed to in- crease due to TCS operation.
The indicators should illuminate when the igni-
tion key is turned to "ON" or "START" but should
go out after three seconds.
If the indicators do not illuminate, or the TCS or
TCS-OFF indicator does not go out after 3
seconds, have it checked by an authorized
dealer.
Should there be any unusual conditions in the device while driving, TCS-OFF indicator illumi- nates as a warning. If TCS-OFF indicator illuminates, pull your car to a safe place and stop the engine. Then, start the engine again to check if the TCS- OFF indicator goes out.
If the indicator remains lit even after the engine has been started, have your car checked by an authorized Hyundai dealer.
NOTE: 1) When the TCS-OFF indicator illuminates, traction control is automatically deacti- vated for safety.
2) This warning function is not provided when the driver selects the TCS-OFF mode.
WARNING:
Nothing should be carried on top of the shelf panel behind the rear seat. If there were an accident or a sudden stop, such objects could move forward and cause damage to the vehicle or injure the occu- pants.
o After being parked, check to be sure the parking brake is not engaged and that the parking brake indicator light is out before driving away.
o Driving through water may get the brakes wet. They can also get wet when the car is washed. Wet brakes can be dangerous! Your car will not stop as quickly if the brakes are wet. Wet brakes may cause the car to pull to one side. To dry the brakes, apply the brakes lightly until the braking action returns to normal, taking care to keep the car under control at all times. If the braking action does not return to normal, stop as soon as it is safe to do so and call your Hyundai dealer for assistance.
xgflhma-2.p65
10
6/16/04, 3:00 PM
o Don't coast down hills with the car out of gear. This is extremely hazardous. Keep the car in gear at all times, use the brakes to slow down, then shift to a lower gear so that engine braking will help you maintain a safe speed. o Don't "ride" the brake pedal. Resting your foot on the brake pedal while driving can be dangerous because it can result in the brakes overheating and losing their effectiveness. It also increases the wear of the brake com- ponents.
o If a tire goes flat while you are driving, apply the brakes gently and keep the car pointed straight ahead while you slow down. When you are moving slowly enough for it to be safe to do so, pull off the road and stop in a safe place.
o Don't let your car creep forward. To avoid creeping forward, keep your foot firmly on the brake pedal when the car is stopped.
o Use caution when parking on a hill. Engage the parking brake and place the gear selec- tor lever in "P". If your car is facing downhill, turn the front wheels into the curb to help keep the car from rolling. If your car is facing uphill, turn the front wheels away from the curb to help keep the car from rolling. If there is no curb or if it is required by other condi- tions to keep the car from rolling, block the wheels.
o Under some conditions your parking brake can freeze in the engaged position. This is most likely to happen when there is an ac- cumulation of snow or ice around or near the rear brakes or if the brakes are wet. If there is a risk that the parking brake may freeze, apply it only temporarily while you put the gear selector lever in "P" and block the rear wheels so the car cannot roll. Then release the parking brake.
o Do not hold the vehicle on the upgrade with the accelerator pedal. This can cause the transaxle to overheat. Always use the brake pedal or parking brake.
DRIVING YOUR HYUNDAI
DRIVING FOR ECONOMY
11
C140A01A-AAT You can save fuel and get more miles from your car if you follow these suggestions:
o Drive smoothly. Accelerate at a moderate rate. Don't make "jack-rabbit" starts or full- throttle shifts and maintain a steady cruising speed. Don't race between stoplights. Try to adjust your speed to that of the other traffic so you don't have to change speeds unnec- essarily. Avoid heavy traffic whenever pos- sible. Always maintain a safe distance from other vehicles so you can avoid unneces- sary braking. This also reduces brake wear. o Drive at a moderate speed. The faster you drive, the more fuel your car uses. Driving at a moderate speed, especially on the high- way, is one of the most effective ways to reduce fuel consumption.
o Don't "ride" the brake or clutch pedal. This can increase fuel consumption and also increase wear on these components. In addition, driving with your foot resting on the brake pedal may cause the brakes to over- heat, which reduces their effectiveness and may lead to more serious consequences. o Take care of your tires. Keep them inflated to the recommended pressure. Incorrect inflation, either too much or too little, results in unnecessary tire wear. Check the tire pressures at least once a month.
xgflhma-2.p65
11
6/16/04, 3:00 PM
SMOOTH CORNERING
C150A01A-AAT Avoid braking or gear changing in corners, especially when roads are wet. Ideally, corners should always be taken under gentle accelera- tion. If you follow these suggestions, tire wear will be held to a minimum.
o Remember, your Hyundai does not require extended warm-up. As soon as the engine is running smoothly, you can drive away. In very cold weather, however, give your en- gine a slightly longer warm-up period.
o Don't "lug" or "over-rev" the engine. Lugging is driving too slowly in too high a gear result- ing in the engine bucking. If this happens, shift to a lower gear. Over-revving is racing the engine beyond its safe limit. This can be avoided by shifting at the recommended speeds.
o Use your air conditioning sparingly. The air conditioning system is operated by engine power so your fuel economy is reduced when you use it.
2 DRIVING YOUR HYUNDAI
12
o Be sure that the wheels are aligned cor- rectly. Improper alignment can result from hitting curbs or driving too fast over irregular surfaces. Poor alignment causes faster tire wear and may also result in other problems as well as greater fuel consumption.
o Keep your car in good condition. For better fuel economy and reduced maintenance costs, maintain your car in accordance with the maintenance schedule in Section 5. If you drive your car in severe conditions, more frequent maintenance is required (see Section 5 for details).
o Keep your car clean. For maximum service, your Hyundai should be kept clean and free of corrosive materials. It is especially impor- tant that mud, dirt, ice, etc. not be allowed to accumulate on the underside of the car. This extra weight can result in increased fuel consumption and also contribute to corro- sion.
o Travel lightly. Don't carry unnecessary weight in your car. Weight reduces fuel economy.
o Don't let the engine idle longer than neces- sary. If you are waiting (and not in traffic), turn off your engine and restart only when you're ready to go.
xgflhma-2.p65
12
6/16/04, 3:00 PM
WINTER DRIVING
C160A01A-AAT The more severe weather conditions of winter result in greater wear and other problems. To minimize the problems of winter driving, you should follow these suggestions:
DRIVING YOUR HYUNDAI
13
C160B01A-AAT Snowy or Icy Conditions
To drive your vehicle in deep snow, it may be necessary to use snow tires or to install tire chains on your tires. If snow tires are needed, it is necessary to select tires equivalent in size and type of the original equipment tires. Failure to do so may adversely affect the safety and handling of your car. Furthermore, speeding, rapid acceleration, sudden brake applications, and sharp turns are potentially very hazardous practices. During deceleration, use engine braking to the fullest extent. Sudden brake applications on snowy or icy roads may cause skids to occur. You need to keep sufficient distance between the vehicle in operation in front and your vehicle. Also, apply the brake gently. It should be noted that installing tire chains on the tire will provide a greater driving force, but will not prevent side skids.
NOTE: Tire chains are not legal in all states. Check state laws before fitting tire chains.
C160C01A-AAT Use High Quality Ethylene Glycol Coolant
Your Hyundai is delivered with high quality ethylene glycol coolant in the cooling system. It is the only type of coolant that should be used because it helps prevent corrosion in the cool- ing system, lubricates the water pump and prevents freezing. Be sure to replace or replen- ish your coolant in accordance with the main- tenance schedule in Section 5. Before winter, have your coolant tested to assure that its freezing point is sufficient for the temperatures anticipated during the winter.
C160D01A-AAT Check Battery and Cables
Winter puts additional burdens on the battery system. Visually inspect the battery and cables as described in Section 6. The level of charge in your battery can be checked by your Hyundai dealer or a service station.
xgflhma-2.p65
13
6/16/04, 3:00 PM
2 DRIVING YOUR HYUNDAI
14
C160E01A-AAT Change to "Winter Weight" Oil if Necessary
In some climates it is recommended that a lower viscosity "winter weight" oil be used during cold weather. See Section 9 for recommendations. If you aren't sure what weight oil you should use, consult your Hyundai dealer.
C160F01A-AAT Check Spark Plugs and Ignition System
Inspect your spark plugs as described in Sec- tion 6 and replace them if necessary. Also check all ignition wiring and components to be sure they are not cracked, worn or damaged in any way.
C160G01A-AAT To Keep Locks from Freezing
C160I01L-AAT Don't Let Your Parking Brake Freeze
To keep the locks from freezing, squirt an approved de-icer fluid or glycerine into the key opening. If a lock is covered with ice, squirt it with an approved de-icing fluid to remove the ice. If the lock is frozen internally, you may be able to thaw it out by using a heated key. Handle the heated key with care to avoid injury.
C160H01A-AAT Use Approved Anti-Freeze in Window Washer System
To keep the water in the window washer system from freezing, add an approved anti-freeze solution in accordance with instructions on the container. Window washer anti-freeze is avail- able from Hyundai dealers and most auto parts outlets. Do not use engine coolant or other types of anti-freeze as these may damage the finish.
Under some conditions your parking brake can freeze in the engaged position. This is most likely to happen when there is an accumulation of snow or ice around or near the rear brakes or if the brakes are wet. If there is a risk the parking brake may freeze, apply it only tempo- rarily while you put the gear selector lever in "P" and block the rear wheels so the car cannot roll. Then release the parking brake.
C160J01A-AAT Don't Let Ice and Snow Accumulate Underneath
Under some conditions, snow and ice can build up under the fenders and interfere with the steering. When driving in severe winter condi- tions where this may happen, you should peri- odically check underneath the car to be sure the movement of the front wheels and the steering components is not obstructed.
xgflhma-2.p65
14
6/16/04, 3:00 PM
2. Fuel, engine coolant and engine oil: High speed travel consumes more fuel than urban motoring. Do not forget to check both engine coolant and engine oil.
3. Drive belt: A loose or damaged drive belt may result in overheating of the engine.
C180A01A-AAT USE OF LIGHTS
Check your lights regularly for correct opera- tion and always keep them clean. When driving during the day in conditions of poor visibility, it is helpful to drive with headlights on low beam. This enables you to be seen as well as to see.
C160K01A-AAT Carry Emergency Equipment
Depending on the severity of the weather where you drive your car, you should carry appropri- ate emergency equipment. Some of the items you may want to carry include tire chains, tow straps or chains, flashlight, emergency flares, sand, a shovel, jumper cables, a window scraper, gloves, ground cloth, coveralls, a blanket, etc.
C170A01A-AAT HIGHER SPEED MOTORING
Pre-Trip Inspections
1. Tires: Adjust the tire inflation pressures to specifica- tion. Low tire inflation pressures will result in overheating and possible failure of the tires. Avoid using worn or damaged tires which may result in reduced traction or tire failure.
NOTE: Never exceed the maximum tire inflation pressure shown on the tires.
DRIVING YOUR HYUNDAI
TRAILER OR VEHICLE TOWING
15
C190A01A-AAT If you are considering towing with your car, you should first check with your State's Department of Motor Vehicles to determine their legal re- quirements. Since laws vary from state to state the require- ments for towing trailers, cars, or other types of vehicles or apparatus may differ. Ask your Hyundai dealer for further details before towing.
CAUTION: Do not do any towing with your car during its first 1,200 miles (2,000 km) in order to allow the engine to properly break in. Fail- ure to heed this caution may result in seri- ous engine or transaxle damage.
C190B01S-AAT Trailer Hitches
Select the proper hitch and ball combination, making sure that its location is compatible with that of the trailer or vehicle being towed. Use a quality non-equalizing hitch which distrib- utes the tongue load uniformly throughout the chassis.
The hitch should be bolted securely to the car and installed by a qualified technician. DO NOT USE A HITCH DESIGNED FOR TEMPORARY INSTALLATION AND NEVER USE ONE THAT ATTACHES ONLY TO THE BUMPER.
xgflhma-2.p65
15
6/16/04, 3:00 PM
2 DRIVING YOUR HYUNDAI
16
C190C01Y-AAT Trailer Brakes
C190D01A-AAT Safety Chains
C190E02L-AAT Trailer Weight Limit
If your trailer is equipped with a braking system, make sure it conforms to federal and/or local regulations and that it is properly installed and operating correctly.
NOTE: If you tow a trailer or vehicle, your car will require more frequent maintenance due to the additional load. See Maintenance Under Severe Usage Conditions" on page 5-6.
Should the hitch connection between your car and the trailer or vehicle you are towing fail, the trailer or vehicle could wander dangerously across other lanes of traffic and ultimately leave the roadway. To eliminate this potentially dan- gerous situation, safety chains, attached be- tween your car and the trailer or towed vehicle, are required in most states.
CAUTION:
o Never connect a trailer brake system
directly to the vehicle brake system.
o When towing a trailer on steep grades (in excess of 12%) pay close attention to the engine coolant temperature gauge to ensure the engine does not overheat. If the needle of the coolant temperature gauge moves across the dial towards "H" (HOT), pull over and stop as soon as it is safe to do so, and allow the engine to idle until it cools down. You may proceed once the engine has cooled sufficiently.
Tongue load
Total trailer weight
C190E01L o Keep the tongue load 10% of the total trailer
load.
Tongue load
Total trailer weight
x 100 = 10 % (MAX)
o Tongue loads can be increased or de- creased by redistributing the load in the trailer. This can be verified by checking the total weight of the loaded trailer and then checking the load on the tongue.
xgflhma-2.p65
16
6/16/04, 3:00 PM
DRIVING YOUR HYUNDAI
17
WARNING:
o Improperly loading your vehicle and trailer can seriously affect its steering and braking performance causing a crash which could cause serious injury or death.
o Towing a trailer affected vehicle han-
dling and braking.
o Drive more slowly when towing a trailer and allow more distance when braking. o Be careful when driving in slippery and
windy conditions.
o Be careful when turning and while driv-
ing up and down hills.
o Do not exceed 45 mph or the posted towing speed limit, whichever is lower.
NOTE: 1. Never load the trailer with more weight in the back than in the front. About 60% of the trailer load should be in the front half on the trailer and the remaining 40% in the rear.
3. The front or rear axle weight must not exceed the Gross Axle Weight Rating (GAWR) shown on the vehicle identifi- cation plate (see page 8-2). It is possible that your towing package does not ex- ceed the GVWR but exceeds the GAWR. Improper trailer loading and/or too much luggage in the trunk can overload the rear axle. Redistribute the load and check the axle weight again.
CAUTION:
The following specifications are recom- mended when towing a trailer. The loaded trailer weight cannot safely exceed the val- ues in the chart.
Lbs. (kg)
Maximum Towable Weight Tongue
Trailer
2000 (907) 1000 (453)
200 (90.7) 100 (45.3)
With Brake
Without Brake
Gross axle weight Gross vehicle weight
C190E02L
2. The total gross vehicle weight with trailer must not exceed the Gross Vehicle Weight Rating (GVWR) shown on the vehicle identification plate (see page 8- 2). The total gross vehicle weight is the combined weight of the vehicle, driver, all passengers and their luggage, cargo, hitch, trailer tongue load and other op- tional equipment.
xgflhma-2.p65
17
6/16/04, 3:00 PM
2 DRIVING YOUR HYUNDAI
18
C190F01L-AAT Trailer or Vehicle Towing Tips
1. Before towing, check hitch and safety chain connections as well as proper operation of the trailer running lights, brake lights, and turn signals.
2. Always drive your vehicle at a moderate
speed (Less than 60 mph)
3. Trailer towing requires more fuel than normal
conditions.
4. To maintain engine braking efficiency, do not tow a trailer with the transaxle engaged in an overdrive gear.
5. Always secure items in the trailer to prevent
load shift while driving.
6. Check the condition and air pressure of all tires on the trailer and your car. Low tire pressure can seriously affect the handling. Also check the spare tire.
7. The vehicle/trailer combination is more af-
fected by crosswind and buffeting. When being passed by a large vehicle, keep a constant speed and steer straight ahead. If there is too much wind buffeting, slow down to get out of the other vehicle's air turbulence. 8. When parking your car and trailer, especially on a hill, be sure to follow all the normal precautions. Turn your front wheel into the curb, set the parking brake firmly, and put the transaxle in Park. In addition, place wheel chocks at each of the trailer's tires.
CAUTION:
If overheating should occur when towing, (the temperature gauge reads near red zone), taking the following action may reduce or eliminate the problem.
1. Turn off the air conditioner. 2. Reduce highway speed. 3. Select a lower gear when going uphill. 4. While in stop and go traffic, place the gear selector in park or neutral and idle the engine at a higher speed.
9.
If the trailer has electric brakes, start your vehicle and trailer moving, and then apply the trailer brake controller by hand to be sure the brakes are working. This lets you check your electrical connection at the same time. 10.During your trip, check occasionally to be sure that the load is secure, and that the lights and any trailer brakes are still working. 11.Avoid jerky starts, sudden acceleration or
sudden stops.
12.Avoid sharp turns and rapid lane changes. 13.Avoid holding the brake pedal down too long or too frequently. This could cause the brakes to overheat, resulting in reduced braking efficiency.
14.When going down a hill, shift into a lower gear
and use the engine braking effect. When ascending a long grade, downshift the transaxle to a lower gear and reduce speed to reduce chances of engine overloading and/or overheating.
15.If you have to stop while going uphill, do not hold the vehicle in place by pressing on the accelerator. This can cause the automatic transaxle to overheat. Use the parking brake or footbrake.
NOTE: When towing check transaxle fluid more frequently.
xgflhma-2.p65
18
6/16/04, 3:00 PM
DRIVING YOUR HYUNDAI
19
(5)Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calcu- lated in Step 4.
(6)If your vehicle will be towing a trailer, load from your trailer will be trans- ferred to your vehicle. Consult this manual to determine how this re- duces the available cargo and lug- gage load capacity of your vehicle.
VEHICLE LOAD LIMIT
C190F01L-AAT Tire and Loading Information Label
I030B01XG The tire label located on the driver's door edge gives the original tire size, cold tire pressures recommended for your vehicle, the number of people that can be in your vehicle and vehicle capacity weight.
Steps for Determining Correct Load Limit (1)Locate the statement "The combined weight of occupants and cargo should never exceed XXX pounds'' on your vehicle's placard.
(2)Determine the combined weight of the driver and passengers that will be riding in your vehicle.
(3)Subtract the combined weight of the driver and passengers from XXX kilograms or XXX pounds.
(4)The resulting figure equals the avail- able amount of cargo and luggage load capacity. For example, if the "XXX" amount equals 1400 lbs, and there will be five 150 lb. passengers in your vehicle, the amount of avail- able cargo and luggage load capac- ity is 650 lbs. (1400-750 (5 x 150) = 650 lbs.)
xgflhma-2.p65
19
6/16/04, 3:00 PM
2 DRIVING YOUR HYUNDAI
20
Example 1
Example 2
Example 3
Item
Description
Vehicle Capacity Weight
C190F01JM
Total
1400 lbs
(640 kg)
Item
Description
Vehicle Capacity Weight
C190F02JM
Total
1400 lbs
(640 kg)
Item
Description
Vehicle Capacity Weight
C190F03JM
Total
1400 lbs
(640 kg)
Subtract Occupant Weight
300 lbs
150 lbs (70 kg) × 2
Available Cargo and
Luggage weight
(140 kg)
1100 lbs
(500 kg)
Subtract Occupant Weight
750 lbs
150 lbs (70 kg) x 5
Available Cargo and
Luggage Weight
(350 kg)
650 lbs
(290 kg)
Subtract Occupant Weight
860 lbs
172 lbs (78 kg) x 5
Available Cargo Weight
(390 kg)
540 lbs
(250 kg)
xgflhma-2.p65
20
6/16/04, 3:00 PM
C190G01L-AAT Compliance Label
Refer to your vehicle’s tire and loading information label for specific informa- tion about your vehicle’s capacity weight and seating positions. The combined weight of the driver, passengers and cargo should never exceed your vehicle’s capacity weight.
C190G01JM The compliance label is located on the driver's side of the center piller outer panel.
The label shows the size of your original tires and the inflation pressures needed to obtain the gross weight capacity of your vehicle. This is called the GVWR (Gross Vehicle Weight Rating). The GVWR includes the weight of the ve- hicle, all occupants, fuel and cargo.
DRIVING YOUR HYUNDAI