2012 Hyundai Accent Owners Manual

when the engine and radiator are hot. Scalding hot coolant and steam may blow out under pres- sure causing serious injury.

Changing the coolant Have coolant changed by an authorized HYUNDAI dealer according the Maintenance Schedule at the beginning of this section.

to

CAUTION

Put a thick cloth or fabric around the radiator cap before refilling the coolant in order to prevent the coolant from overflowing into engine parts such as generator.

WARNING - Coolant

(cid:129) Do not use radiator coolant or antifreeze in the washer fluid reservoir.

(cid:129) Radiator coolant can severely obscure visibility when sprayed on the windshield and may cause loss of vehicle control or damage to paint and body trim.

Maintenance

7 25

Maintenance

BRAKE/CLUTCH FLUID

ORBC070007

fluid

Checking the brake/clutch fluid level Check the fluid level in the reservoir peri- odically. The level should be between MAX and MIN marks on the side of the reservoir. Before removing the reservoir cap and adding brake/clutch fluid, clean the area around the reservoir cap thoroughly to prevent brake/clutch fluid contamination. If the level is low, add fluid to the MAX level. The level will fall with accumulated mileage. This is a normal condition asso- ciated with the wear of the brake linings. If the fluid level is excessively low, have the brake system or clutch (if equipped) checked by an authorized HYUNDAI dealer.

26

Use only the specified brake fluid.(Refer to “Recommended lubricants or capaci- ties”in section 8.)

Never mix different types of fluid.

WARNING - Loss of brake/

clutch fluid

In the event the brake system requires frequent additions of fluid, the vehicle should be inspected by an authorized HYUNDAI dealer.

CAUTION

Do not allow brake fluid to contact the vehicle's body paint, as paint damage will result. Brake fluid, which has been exposed to open air for an extended time should never be used as its quality cannot be guaranteed. It should be disposed of properly.Don't put in the wrong kind of fluid.A few drops of miner- al-based oil, such as engine oil, in your brake system can damage brake system parts.

WARNING - Brake/clutch

fluid

When changing and adding brake fluid, handle it carefully. Do not let it come in contact with your eyes. If brake fluid should come in contact with your eyes, immediately flush them with a large quantity of fresh tap water. Have your eyes examined by a doctor as soon as possible.

WASHER FLUID

PARKING BRAKE

Maintenance

WARNING - Coolant

(cid:129) Do not use radiator coolant or antifreeze in the washer fluid reservoir.

(cid:129) Radiator coolant can severely obscure visibility when sprayed on the windshield and may cause loss of vehicle control or damage to paint and body trim.

(cid:129) Windshield washer fluid agents contain some amounts of alcohol and can be flammable under cer- tain circumstances. Do not allow sparks or flame to contact the washer fluid or the washer fluid reservoir. Damage to the vehicle or occupants could occur.

(cid:129) Windshield washer fluid is poi- sonous to humans and animals. Do not drink and avoid contacting windshield washer fluid. Serious injury or death could occur.

ORBC070009

Checking the washer fluid level The reservoir is translucent so that you can check the level with a quick visual inspection. Check the fluid level in the washer fluid reservoir and add fluid if necessary. Plain water may be used if washer fluid is not available. However, use washer solvent with antifreeze characteristics in cold cli- mates to prevent freezing.

ORB050003

Checking the parking brake Check the stroke of the parking brake by counting the number of “clicks’’ heard while fully applying it from the released position. Also, the parking brake alone should securely hold the vehicle on a fair- ly steep grade. If the stroke is more or less than specified, have the parking brake adjusted by an authorized HYUNDAI dealer.

Stroke : 6~8 “clicks’’ at a force of

44 lbs (20 kg, 196 N).

7 27

Maintenance

AIR CLEANER

ORB070010

Filter replacement It must be replaced when necessary, and should not be cleaned and reused. You can clean the filter when inspecting the air cleaner element. Clean the filter by using compressed air.

ORB070011
1. Loosen the air cleaner cover attaching

clips and open the cover.

ORB070012

2. Wipe the inside of the air cleaner. 3. Replace the air cleaner filter. 4. Lock the cover with the cover attaching

clips.

28

Replace the filter according to the Maintenance Schedule. If the vehicle is operated in extremely dusty or sandy areas, replace the ele- ment more often than the usual recom- mended to “Maintenance under severe usage condi- tions”in this section.)

intervals.

(Refer

CAUTION

(cid:129) Do not drive with the air cleaner removed;this will result in exces- sive engine wear.

(cid:129) When removing the air cleaner fil- ter, be careful that dust or dirt does not enter the air intake, or damage may result.

(cid:129) Use a HYUNDAI genuine part.Use of non-genuine parts could dam- age the air flow sensor and engine.

CLIMATE CONTROL AIR FILTER Filter inspection The climate control air filter should be replaced according to the Maintenance Schedule. If the vehicle is operated in severely air-polluted cities or on dusty rough roads for a long period, it should be frequently and replaced earlier. When you replace the climate control air filter, replace it per- forming the following procedure, and be careful to avoid damaging other compo- nents.

inspected more

Maintenance

ORB070060

Filter replacement 1. With the glove box open, remove the stoppers by turning them counter- clockwise on both sides.

7 29

Maintenance

2. Remove the support strap (1).

ORB070013

ORB070014
3. Remove the climate control air filter cover (2) while pressing the lock (1) on the right of the cover.

OYF079046

4. Replace the climate control air filter. 5. Reassemble in the reverse order of

disassembly.

✽✽ NOTICE When replacing the climate control air filter install it properly. Otherwise, the system may produce noise and the effec- tiveness of the filter may be reduced.

30

WIPER BLADES

1JBA5122

Blade inspection ✽✽ NOTICE Commercial hot waxes applied by auto- matic car washes have been known to make the windshield difficult to clean.

Maintenance

Contamination of either the windshield or the wiper blades with foreign matter can reduce the effectiveness of the wind- shield wipers. Common sources of con- tamination are insects, tree sap, and hot wax treatments used by some commer- cial car washes. If the blades are not wip- ing properly, clean both the window and the blades with a good cleaner or mild detergent, and rinse thoroughly with clean water.

Blade replacement When the wipers no longer clean ade- quately, the blades may be worn or cracked, and require replacement.

CAUTION

To prevent damage to the wiper arms or other components, do not attempt to move the wipers manual- ly.

CAUTION

To prevent damage to the wiper blades, do not use gasoline, kerosene, paint thinner, or other solvents on or near them.

CAUTION

The use of a non-specified wiper blade could result in wiper malfunc- tion and failure.

7 31

Maintenance

OLM079200

Front windshield wiper blade Type A 1. Raise the wiper arm and turn the wiper blade assembly to expose the plastic locking clip.

OLM079201
2. Compress the clip and slide the blade

assembly downward.

3. Lift it off the arm. 4. Install the blade assembly in the

reverse order of removal.

CAUTION

Do not allow the wiper arm to fall against the windshield,since it may chip or crack the windshield.

OHM078059

Front windshield wiper blade Type B 1. Raise the wiper arm.

CAUTION

Do not allow the wiper arm to fall against the windshield,since it may chip or crack the windshield.

32

OYF079061

OHM078062

Rear window wiper blade (if equipped) 1. Raise the wiper arm and pull out the

wiper blade assembly.

OYF079062
2. Lift up the wiper blade clip. Then pull down the blade assembly and remove it.

3. Install the new blade assembly in the

reverse order of removal.

Maintenance

OHM078063
2. Install the new blade assembly by inserting the center part into the slot in the wiper arm until it clicks into place. 3. Make sure the blade assembly is installed firmly by trying to pull it slight- ly.

To prevent damage to the wiper arms or other components, have an authorized HYUNDAI dealer replace the wiper blade.

7 33

Maintenance

BATTERY

ORB070016

For best battery service (cid:129) Keep the battery securely mounted. (cid:129) Keep the battery top clean and dry. (cid:129) Keep the terminals and connections clean, tight, and coated with petroleum jelly or terminal grease.

(cid:129) Rinse any spilled electrolyte from the battery immediately with a solution of water and baking soda.

(cid:129) If the vehicle is not going to be used for an extended time, disconnect the bat- tery cables.

34

WARNING - Battery dangers

Always read the following instructions carefully when handling a battery. Keep lighted cigarettes and all other flames or sparks away from the battery. Hydrogen, a highly com- bustible gas, is always present in battery cells and may explode if ignited. Keep batteries out of the reach of children because batteries contain highly corrosive SULFURIC ACID. Do not allow battery acid to contact your skin, eyes, clothing or paint finish. If any electrolyte gets into your eyes, flush your eyes with clean water for at least 15 minutes and get immedi- ate medical attention.

(Continued)

(Continued)

If electrolyte gets on your skin, thoroughly wash the contacted area. If you feel a pain or a burning sensa- tion, get medical attention immediately. Wear eye protection when charging or working near a battery. Always provide ventilation when working in an enclosed space. An inappropriately disposed battery can be harmful to the environment and human health. Dispose the battery according to your local law(s) or regulation. The battery contains lead. Do not dispose of it after use. Please return the battery to an authorized HYUNDAI dealer to be recycled.

Pb

(cid:129) When lifting a plastic-cased bat- tery, excessive pressure on the case may cause battery acid to leak, resulting in personal injury. Lift with a battery carrier or with your hands on opposite corners. (Continued)

Maintenance

(Continued) (cid:129) Never attempt to recharge the battery when the battery cables are connected.

(cid:129) The electrical ignition system works with high voltage. Never touch these components with the engine running or the ignition switched on.

Failure to follow the above warn- ings can result in serious bodily injury or death.

CAUTION

(cid:129) When you don’t use the vehicle for a long time in low temperature area, separate the battery and keep it indoors.

(cid:129) Always charge the battery fully to prevent battery case damage in low temperature area.

(cid:129) If you connect unauthorized elec- tronic devices to the battery, the battery may be discharged.Never use unauthorized devices.

Battery recharging Your vehicle has a maintenance-free, calcium-based battery. If the battery becomes discharged in a short time (because, for example the headlights or interior lights were left on while vehicle was not in use) jump start the vehicle from another battery and run the engine at least 20 minutes at idle before driving. Do not turn off the engine for 30 minutes total of idle and/or driving as the battery may not have sufficient recharge to start.

WARNING

Separating the battery from the vehicle should be done in an authorized HYUNDAI dealer.

CALIFORNIA PROPOSI- TION 65 WARNING

Battery posts, terminals, and relat- ed accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer, birth defects and reproduc- tive harm. Batteries also contain other chemicals known to the State of California to cause cancer. Wash hands after handling.

7 35

WARNING

(cid:129) Before performing maintenance or recharging the battery, turn off all accessories and stop the engine.

(cid:129) The negative battery cable must be removed first and installed last when the battery is discon- nected.

(cid:129) Operation related to the battery should be done in an authorized HYUNDAI dealer.

Reset items Items should be reset after the battery has been discharged or the battery has been disconnected. (cid:129) Auto up/down window (See section 4) (cid:129) Sunroof (See section 4) (cid:129) Trip computer (See section 4) (cid:129) Climate control system

(See section 4)

(cid:129) Clock (See section 4) (cid:129) Audio (See section 4)

Maintenance

WARNING - Recharging

battery

recharging

When the battery, observe the following precautions: (cid:129) The battery must be removed from the vehicle and placed in an area with good ventilation.

(cid:129) Do not allow cigarettes, sparks,

or flame near the battery.

(cid:129) Watch the battery during charg- ing, and stop or reduce the charg- ing rate if the battery cells begin gassing (boiling) violently or if the temperature of the electrolyte of any cell exceeds 120°F (49°C). (cid:129) Wear eye protection when check-

ing the battery during charging.

(cid:129) Disconnect the battery charger in

the following order.

1. Turn off the battery charger main

switch.

2. Unhook the negative clamp from

the negative battery terminal.

3. Unhook the positive clamp from

the positive battery terminal.

36

TIRES AND WHEELS Tire care For proper maintenance, safety, and maximum fuel economy, you must always maintain recommended tire inflation pressures and stay within the load limits and weight distribution recommended for your vehicle.

Recommended cold tire inflation pressures All tire pressures (including the spare) should be checked when the tires are cold. “Cold Tires” means the vehicle has not been driven for at least three hours or driven less than one mile (1.6 km). Recommended pressures must be maintained for the best ride, vehicle handling, and minimum tire wear. For recommended inflation pressure, refer to “Tire and wheels” in section 8.

Maintenance

CAUTION

(cid:129) Underinflation also results in excessive wear,poor handling and reduced fuel economy. Wheel deformation also is possible.Keep your tire pres- sures at the proper levels.If a tire frequently needs refilling, have it checked by an author- ized HYUNDAI dealer.

(cid:129) Overinflation produces a harsh ride, excessive wear at the center of the tire tread,and a greater possibility of dam- age from road hazards.

ORB070017
All specifications (sizes and pres- sures) can be found on a label attached to the driver’s side center pillar.

WARNING - Tire underin-

flation

Severe underinflation can lead to severe heat build-up, causing blowouts, tread separation and other tire failures that can result in the loss of vehicle control leading to severe injury or death. This risk is much higher on hot days and when driving for long periods at high speeds.

7 37

CAUTION - Tire pressure Always observe the following: (cid:129) Check tire pressure when the tires are cold. (After vehicle has been parked for at least three hours or hasn't been driven more than one mile (1.6
km) since startup.)

(cid:129) Check the pressure of your spare tire each time you check the pressure of other tires.

(cid:129) Never overload your vehicle. Be careful not to overload a vehicle luggage rack if your vehicle is equipped with one. (cid:129) Worn,old tires can cause acci- dents. If your tread is badly worn, or if your tires have been damaged,replace them.

Checking tire inflation pressure Check your tires once a month or more. Also, check the tire pressure of the spare tire.

How to check Use a good quality gage to check tire pressure. You can not tell if your tires are properly inflated simply by look- ing at them. Radial tires may look properly inflated even when they're underinflated. Check the tire's inflation pressure when the tires are cold. - "Cold" means your vehicle has been sitting for at least three hours or driven no more than 1 mile (1.6 km).

Maintenance

CAUTION

(cid:129) Warm tires normally exceed recommended cold tire pres- sures by 4 to 6 psi (28 to 41
kPa). Do not release air from warm tires to adjust the pres- sure or the tires will be under- inflated.

(cid:129) Be sure to reinstall the tire inflation valve caps. Without the valve cap,dirt or moisture could get into the valve core and cause air leakage. If a valve cap is missing,install a new one as soon as possible.

WARNING - Tire Inflation Overinflation or underinflation can reduce tire life, adversely affect vehicle handling, and lead to sudden tire failure. This could result in loss of vehicle control and potential injury.

38

Remove the valve cap from the tire valve stem. Press the tire gage firm- ly onto the valve to get a pressure measurement. If the cold tire inflation pressure matches the recommended pressure on the tire and loading information label, no further adjust- ment is necessary. If the pressure is low, add air until you reach the rec- ommended amount. If you overfill the tire, release air by pushing on the metal stem in the center of the tire valve. Recheck the tire pressure with the tire gage. Be sure to put the valve caps back on the valve stems. They help prevent leaks by keeping out dirt and mois- ture.

WARNING

(cid:129) Inspect your tires frequently for proper inflation as well as wear and damage. Always use a tire pressure gauge.

(cid:129) Tires with too much or too little pressure wear unevenly caus- ing poor handling, loss of vehi- cle control, and sudden tire failure leading to accidents, injuries, and even death. The recommended cold tire pres- sure for your vehicle can be found in this manual and on the tire label located on the dri- ver's side center pillar.

(cid:129) Worn tires can cause acci- dents. Replace tires that are worn, show uneven wear, or are damaged.

(cid:129) Remember to check the pres- sure of your spare tire. HYUNDAI recommends that you check the spare every time you check the pressure of the other tires on your vehi- cle.

Maintenance

Tire rotation To equalize tread wear, it is recom- mended that the tires be rotated every 7,500 miles (12,000 km) or sooner if irregular wear develops. During rotation, check the tires for correct balance. When rotating tires, check for uneven wear and damage. Abnormal wear is usually caused by incorrect tire pres- sure, improper wheel alignment, out- of-balance wheels, severe braking or severe cornering. Look for bumps or bulges in the tread or side of tire. Replace the tire if you find either of these conditions. Replace the tire if fabric or cord is visible. After rotation, be sure to bring the front and rear tire pressures to specification and check lug nut tightness.

7 39

WARNING

(cid:129) Do not use the compact spare tire (if equipped) for tire rota- tion.

(cid:129) Do not mix bias ply and radial ply tires under any circum- stances. This may cause unusual handling characteris- tics that could result in death, severe injury, or property damage.

Wheel alignment and tire balance The wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. In most cases, you will not need to have your wheels aligned again. However, if you notice unusual tire wear or your vehicle pulling one way or the other, the alignment may need to be reset. If you notice your vehicle vibrating when driving on a smooth road, your wheels may need to be rebalanced.

CAUTION

Improper wheel weights can damage your vehicle's alu- minum wheels. Use only approved wheel weights.

Maintenance

Without a spare tire

OBH078040
Disc brake pads should be inspected for wear whenever tires are rotated.

✽✽ NOTICE Rotate radial tires that have an asymmetric tread pattern only from front to rear and not from right to left.

40

Tread wear indicator

OEN076053

Tire replacement If the tire is worn evenly, a tread wear indicator will appear as a solid band across the tread. This shows there is less than 1/16 inch (1.6 mm) of tread left on the tire. Replace the tire when this happens. Do not wait for the band to appear across the entire tread before replac- ing the tire.

WARNING - Replacing

tires

To reduce the chance or serious or fatal injuries from an acci- dent caused by tire failure or loss of vehicle control: (cid:129) Replace tires that are worn, show uneven wear, or are damaged. Worn tires can cause loss of braking effec- tiveness, steering control, and traction.

(cid:129) Do not drive your vehicle with too little or too much pressure in your tires. This can lead to uneven wear and tire failure.

(cid:129) When replacing tires, never mix radial and bias-ply tires on the same car. You must replace all tires (including the spare) if moving from radial to bias-ply tires.

(Continued)

Maintenance

(Continued) (cid:129) Using tires and wheel other than the recommended sizes could cause unusual handling characteristics and poor vehi- cle control, resulting in a seri- ous accident.

(cid:129) Wheels that do not meet HYUNDAI’s specifications may fit poorly and result in damage to the vehicle or unusual handling and poor vehicle control.

(cid:129) The ABS works by comparing the speed of the wheels. Tire size can affect wheel speed. When replacing tires, all 4
tires must use the same size originally supplied with the vehicle. Using tires of a differ- ent size can cause the ABS (Anti-lock Brake System) and ESC (Electronic Stability Control) to work irregularly.

7 41

Maintenance

Compact spare tire replacement (if equipped) A compact spare tire has a shorter tread life than a regular size tire. Replace it when you can see the tread wear indicator bars on the tire. The replacement compact spare tire should be the same size and design tire as the one provided with your new vehicle and should be mounted on the same compact spare tire wheel. The compact spare tire is not designed to be mounted on a regular size wheel, and the compact spare tire wheel is not designed for mount- ing a regular size tire.

Wheel replacement When replacing the metal wheels for any reason, make sure the new wheels are equivalent to the original factory units in diameter, rim width and offset.

WARNING

A wheel that is not the correct size may adversely affect wheel and bearing life, braking and stopping abilities, handling char- acteristics, ground clearance, body-to-tire clearance, snow chain clearance, speedometer and odometer calibration, head- light aim and bumper height.

Tire traction Tire traction can be reduced if you drive on worn tires, tires that are improperly inflated or on slippery road surfaces. Tires should be replaced when tread wear indicators appear. To reduce the possibility of losing control, slow down whenever there is rain, snow or ice on the road.

Tire maintenance In addition to proper inflation, correct wheel alignment helps to decrease tire wear. If you find a tire is worn unevenly, have your dealer check the wheel alignment. When you have new tires installed, make sure they are balanced. This will increase vehicle ride comfort and tire life. Additionally, a tire should always be rebalanced if it is removed from the wheel.

42

1

5,6

I030B04JM

information

Tire sidewall labeling This identifies and describes the fundamental charac- teristics of the tire and also provides the tire identification number (TIN) for safety standard certification. The TIN can be used to identify the tire in case of a recall.

1.Manufacturer or brand name Manufacturer or Brand name is shown.

2.Tire size designation A tire’s sidewall is marked with a tire size designation. You will need this information when selecting replace- ment tires for your car. The following explains what the letters and num- bers in the tire size designation mean. Example tire size designation: (These numbers are provided as an example only; your tire size designa- tor could vary depending on your vehicle.) P195/50R16 84H

P - Applicable vehicle type (tires marked with the prefix “P’’ are intended for use on passenger cars or light trucks; however, not all tires have this marking). 195 - Tire width in millimeters. 50 - Aspect ratio. The tire’s section height as a percentage of its width.

R - Tire construction code (Radial). 16 - Rim diameter in inches.

Maintenance

84 - Load Index, a numerical code associated with the maximum load the tire can carry.

H - Speed Rating Symbol. See the speed rating chart in this section for additional information.

Wheel size designation Wheels are also marked with impor- tant information that you need if you ever have to replace one. The follow- ing explains what the letters and numbers in the wheel size designa- tion mean.

Example wheel size designation: 6.0JX16

6.0 - Rim width in inches. J - Rim contour designation. 16 - Rim diameter in inches.

7 43

Maintenance

Tire speed ratings The chart below lists many of the dif- ferent speed ratings currently being used for passenger car tires. The speed rating is part of the tire size designation on the sidewall of the tire. This symbol corresponds to that tire's designed maximum safe oper- ating speed.

Speed Rating Symbol

Maximum Speed

112 mph (180 km/h)

118 mph (190 km/h)

130 mph (210 km/h)

149 mph (240 km/h)

Above 149 mph (240 km/h)

44

WARNING - Tire age

Tires degrade over time, even when they are not being used. Regardless of the remaining tread, it is recommended that tires generally be replaced after six (6) years of normal service. Heat caused by hot climates or frequent high loading condi- tions can accelerate the aging process. Failure to follow this warning can result in sudden tire failure, which could lead to a loss of control and an acci- dent involving serious injury or death.

3.Checking tire life (TIN :Tire

Identification Number)

Any tires that are over 6 years old, based on the manufacturing date, (including the spare tire) should be replaced by new ones. You can find the manufacturing date on the tire sidewall (possibly on the inside of the wheel), displaying the DOT Code. The DOT Code is a series of num- bers on a tire consisting of numbers and English letters. The manufactur- ing date is designated by the last four digits (characters) of the DOT code.

DOT : XXXX XXXX OOOO The front part of the DOT means a plant code number, tire size and tread pattern and the last four num- bers indicate week and year manu- factured. For example: DOT XXXX XXXX 1611 represents that the tire was produced in the 16th week of 2011.

4.Tire ply composition and material The number of layers or plies of rub- ber-coated fabric in the tire. Tire man- ufacturers also must indicate the materials in the tire, which include steel, nylon, polyester, and others.The letter "R" means radial ply construc- tion; the letter "D" means diagonal or bias ply construction; and the letter "B" means belted-bias ply construction.

5.Maximum permissible inflation

pressure

This number is the greatest amount of air pressure that should be put in the tire. Do not exceed the maximum permissible inflation pressure. Refer to the Tire and Loading Information label inflation pressure.

for recommended

6.Maximum load rating This number indicates the maximum load in kilograms and pounds that can be carried by the tire. When replacing the tires on the vehicle, always use a tire that has the same load rating as the factory installed tire.

Maintenance

the

7.Uniform tire quality grading Quality grades can be found where applicable on tire sidewall between tread shoulder and maxi- mum section width. For example: TREAD wear 200 TRACTION AA TEMPERATURE A

Traction - AA, A, B & C The traction grades, from highest to lowest, are AA, A, B and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on speci- fied government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.

WARNING

The traction grade assigned to this tire is based on straight- ahead braking traction tests, and does not include accelera- tion, cornering, hydroplaning, or peak traction characteristics.

Tread wear The tread wear grade is a compara- tive rating based on the wear rate of the tire when tested under controlled conditions on a specified govern- ment test course. For example, a tire graded 150 would wear one-and-a- half times (1½) as well on the gov- ernment course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate. These grades are molded on the side-walls of passenger vehicle tires. The tires available as standard or optional equipment on your vehicle may vary with respect to grade.

7 45

Maintenance

Temperature -A, B & C The temperature grades are A (the highest), B and C representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled condi- tions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C cor- responds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the labora- tory test wheel than the minimum required by law.

46

WARNING - Tire

temperature

The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat build-up and possible sudden tire failure. This can cause loss of vehicle control and serious injury or death.

are,

Tire terminology and definitions Air Pressure: The amount of air inside the tire pressing outward on the tire. Air pressure is expressed in pounds per square inch (psi) or kilo- pascal (kPa). Accessory Weight: This means the combined weight of optional acces- sories. Some examples of optional accessories automatic transaxle, power seats, and air con- ditioning. Aspect Ratio: The relationship of a tire's height to its width. Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread.

Cold Tire Pressure: The amount of air pressure in a tire, measured in pounds per square inch (psi) or kilo- pascals (kPa) before a tire has built up heat from driving. Curb Weight: This means the weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil and coolant, but without passengers and cargo. DOT Markings: A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation motor vehicle safety standards. The DOT code includes the Tire Identification Number (TIN), an alphanumeric des- ignator which can also identify the tire manufacturer, production plant, brand and date of production. GVWR: Gross Vehicle Weight Rating GAWR FRT: Gross Axle Weight Rating for the Front Axle. GAWR RR: Gross Axle Weight Rating for the Rear axle.

Intended Outboard Sidewall: The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure. Load Index: An assigned number ranging from 1 to 279 that corre- sponds to the load carrying capacity of a tire. Maximum Inflation Pressure: The maximum air pressure to which a cold tire may be inflated. The maxi- mum air pressure is molded onto the sidewall. Maximum Load Rating: The load rating for a tire at the maximum per- missible inflation pressure for that tire. Maximum Loaded Vehicle Weight: The sum of curb weight; accessory weight; vehicle capacity weight; and production options weight. Normal Occupant Weight: The number of occupants a vehicle is designed to seat multiplied by 150
pounds (68 kg).

Maintenance

Occupant Distribution: Designated seating positions. Outward Facing Sidewall: The side of a asymmetrical tire that has a par- ticular side that faces outward when mounted on a vehicle. The outward facing sidewall bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same moldings on the inner facing sidewall. Passenger (P-Metric) Tire: A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inflation Pressure: Vehicle manufacturer's recommend- ed tire inflation pressure and shown on the tire placard. Radial Ply Tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim: A metal support for a tire and upon which the tire beads are seat- ed. Sidewall: The portion of a tire between the tread and the bead.

7 47

Maintenance

Speed Rating: An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. Traction: The friction between the tire and the road surface. The amount of grip provided. Tread: The portion of a tire that comes into contact with the road. Treadwear Indicators: Narrow bands, sometimes called "wear bars," that show across the tread of a tire when only 2/32 inch of tread remains. UTQGS: Uniform Tire Quality Grading Standards, a tire information system that provides consumers with ratings for a tire's traction, tempera- ture and treadwear. Ratings are determined by tire manufacturers using government testing proce- dures. The ratings are molded into the sidewall of the tire. Vehicle Capacity Weight: The num- ber of designated seating positions multiplied by 150 lbs. (68 kg) plus the rated cargo and luggage load.

Vehicle Maximum Load on the Tire: Load on an individual tire due to curb and accessory weight plus maximum occupant and cargo weight. Vehicle Normal Load on the Tire: Load on an individual tire that is determined by distributing to each axle its share of the curb weight, accessory weight, and normal occu- pant weight and dviding by 2. Vehicle Placard: A label permanent- ly attached to a vehicle showing the original equipment tire size and rec- ommended inflation pressure.

All season tires HYUNDAI specifies all season tires on some models to provide good performance for use all year round, including snowy and icy road condi- tions. All season tires are identified by ALL SEASON and/or M+S (Mud and Snow) on the tire sidewall. Snow tires have better snow traction than all season tires and may be more appropriate in some areas.

Summer tires HYUNDAI specifies summer tires on some models to provide superior performance on dry roads. Summer tire performance is substantially reduced in snow and ice. Summer tires do not have the tire traction rat- ing M+S (Mud and Snow) on the tire side wall. if you plan to operate your vehicle in snowy or icy conditions. HYUNDAI recommends the use of snow tires or all season tires on all four wheels.

Snow tires If you equip your car with snow tires, they should be the same size and have the same load capacity as the original tires. Snow tires should be installed on all four wheels; other- wise, poor handling may result. Snow tires should carry 4 psi (28
kPa) more air pressure than the pressure recommended for the stan- dard tires on the tire label on the dri- ver's side of the center pillar, or up to the maximum pressure shown on the tire sidewall, whichever is less.

48

Do not drive faster than 75 mph (120
km/h) when your car is equipped with snow tires.

Tire chains Tire chains, if necessary, should be installed on the front wheels. Be sure that the chains are installed in accordance with the manufactur- er's instructions. To minimize tire and chain wear, do not continue to use tire chains when they are no longer needed.

CAUTION

Since the sidewalls of radial tires are thinner, they can be damaged by mounting some types of snow chains on them. Therefore,the use of snow tires is recommended instead of snow chains.

WARNING - Snow or ice

(cid:129) When driving on roads cov- ered with snow or ice, drive at less than 20 mph (30 km/h).

(cid:129) Use the SAE “S” class or wire

chains.

(cid:129) If you hear noise caused by chains contacting the body, retighten the chain to avoid contact with the vehicle body. (cid:129) To prevent body damage, retighten the chains after driv- ing 0.3~0.6 miles (0.5~1.0 km). (cid:129) Do not use tire chains on vehicles equipped with alu- minum wheels. In unavoid- able circumstance, use a wire type chain.

(cid:129) Use wire chains less than 0.59
inches (15 mm) to prevent damage to the chain’s con- nection.

Maintenance

Radial-ply tires Radial-ply tires provide improved tread life, road hazard resistance and smoother high speed ride. The radi- al-ply tires used on this vehicle are of belted construction, and are selected to complement the ride and handling characteristics of your vehicle. Radial-ply tires have the same load carrying capacity, as bias-ply or bias belted tires of the same size, and use the same recommended inflation pressure. Mixing of radial-ply tires with bias-ply or bias belted tires is not recommended. Any combina- tions of radial-ply and bias-ply or bias belted tires when used on the same vehicle will seriously deteriorate vehicle handling. The best rule to fol- low is: Identical radial-ply tires should always be used as a set of four. Longer wearing tires can be more susceptible to irregular tread wear. It is very important to follow the tire rotation interval shown in this section to achieve the tread life potential of these tires. Cuts and punctures in radial-ply tires are repairable only in the tread area, because of sidewall flexing. Consult your tire dealer for radial-ply tire repairs.

7 49

This vehicle has 2 fuse panels, one locat- ed in the driver’s side panel bolster, the other in the engine compartment. If any of your vehicle’s lights, acces- sories, or controls do not work, check the appropriate circuit fuse. If a fuse has blown, the element inside the fuse will be melted. If the electrical system does not work, first check the driver’s side fuse panel. Always replace a blown fuse with one of the same rating. If the replacement fuse blows, this indi- cates an electrical problem. Avoid using the system involved and immediately consult an authorized HYUNDAI dealer. Three kinds of fuses are used:blade type for lower amperage rating, cartridge type, and multi fuse for higher amperage rat- ings.

WARNING - Fuse replace-

ment

(cid:129) Never replace a fuse with any- thing but another fuse of the same rating.

(cid:129) A higher capacity fuse could cause damage and possibly a fire. (cid:129) Never install a wire or aluminum foil instead of the proper fuse - even as a temporary repair. It may cause extensive wiring damage and a possible fire.

CAUTION

Do not use a screwdriver or any other metal object to remove fuses because it may cause a short circuit and damage the system.

Maintenance

FUSES Blade type

Normal

Blown

Cartridge type

Normal

Blown

Multi fuse

Normal

Blown

ORB072110
A vehicle’s electrical system is protected from electrical overload damage by fuses.

50

Driver’s side panel

Maintenance

If the headlights or other electrical com- ponents do not work and the fuses are OK, check the fuse panel in the engine compartment. If a fuse is blown, it must be replaced.

ORB070018

Instrument panel fuse replace- ment 1. Turn the ignition switch and all other

switches off.

2. Open the fuse panel cover.

ORB070019
3. Pull the suspected fuse straight out. Use the removal tool provided in the engine compartment fuse panel.

4. Check the removed fuse; replace it if it

is blown.

5. Push in a new fuse of the same rating, and make sure it fits tightly in the clips. If it fits loosely, consult an authorized HYUNDAI dealer. If you do not have a spare, use a fuse of the same rating from a circuit you may not need for operating the vehicle, such as the cigarette lighter fuse.

7 51

✽✽ NOTICE • If the memory fuse is pulled up from the fuse panel, the warning chime, audio, clock and interior lamps, etc., will not operate. Some items must be reset after replacement. Refer to “Battery” in this section.

• Even though the memory fuse is pulled up, the battery can still be dis- charged by operation of the head- lights or other electrical devices.

ORB070021

Engine compartment fuse replacement 1. Turn the ignition switch and all other

switches off.

2. Remove the fuse panel cover by

pressing the tab and pulling up.

Maintenance

ORB070020

Memory fuse Your vehicle is equipped with a memory fuse to prevent battery discharge if your vehicle is parked without being operated for prolonged periods. Use the following procedures before parking the vehicle for prolonged periods. 1. Turn off the engine. 2. Turn off the headlights and tail lights. 3. Open the driver’s side panel cover and

pull up the memory fuse.

52

Maintenance

✽✽ NOTICE • If the multi fuse is blown, consult an

authorized HYUNDAI dealer.

• Before remove the multi fuse, discon-

nect the (-) terminal of battery.

3. Check the removed fuse; replace it if it is blown. To remove or insert the fuse, use the fuse puller in the engine com- partment fuse panel.

4. Push in a new fuse of the same rating, and make sure it fits tightly in the clips. If it fits loosely, consult an authorized HYUNDAI dealer.

CAUTION

After checking the fuse panel in the engine compartment, securely install the fuse panel cover. If not, electrical failures may occur from water contact.

ORB070022

Multi fuse If the multi fuse is blown, it must be removed as follows: 1. Turn off the engine. 2. Disconnect the negative battery cable. 3. Remove the fuse panel in the engine

compartment.

4. Remove the nuts shown in the picture

above.

5. Replace the fuse with a new one of the

same rating.

6. Reinstall in the reverse order of

removal.

7 53

Maintenance

Fuse/relay panel description Inside the fuse/relay panel covers, you can find the fuse/relay label describing fuse/relay name and capacity.

Driver’s side panel

Engine compartment

✽✽ NOTICE Not all fuse panel descriptions in this manual may be applicable to your vehi- cle. It is accurate at the time of printing. When you inspect the fuse panel in your vehicle, refer to the fuse panel label.

ORB070023/ORB070024

54

Maintenance

Instrument panel (Driver’s side fuse panel)

Description

Fuse rating

Protected component

P/OUTLET C/LIGHTER ACC A/BAG IND A/BAG T/SIG IG1 2
WIPER RR SPARE 6
SPARE 1
FOG LP FRT ROOM LP 2

STOP LP

CLUSTER

IG1 1

ABS

B/UP LP ECU H/LP LH HAZARD SPARE 2
SUNROOF

15A 15A 10A 10A 10A 10A 10A 15A 15A 10A 10A 10A

15A

10A

10A

10A

10A 10A 10A 15A 25A 15A

Cigarette Lighter & Power Outlet (Power Outlet) Cigarette Lighter & Power Outlet (Cigarette Lighter) Audio, Power Outside Mirror Switch Instrument Cluster (Air Bag IND.) SRS Control Module, Telltale, Passenger Occupant Detection Sensor Hazard Switch Not Used Multifunction Switch (Wiper), Rear Wiper Moter Not Used Not Used Front Fog Lamp Relay Auto Cut Relay Stop Lamp Switch, Battery Sensor, Stop Lamp RelayE/R Fuse & Relay Box (HAC Relay), Data Link Connector Instrument Cluster (MICOM, IND.), BCM Stop Lamp Switch, ECO Switch, Driver/Passenger Seat Heater Module Tire Pressure Monitoring Module, ATM Shift Lever Switch ILL. EPS Control Module, Rheostat

ABS Control Module, ESC Control Module, ESC Off Switch E/R Fuse & Relay Box (Multipurpose Check Connector, HAC Relay) Back-Up Lamp Switch ECM, PCM Head Lamp LH Hazard Relay, Hazard Switch Not Used Sunroof Motor

7 55

Maintenance

Description

Fuse rating

Protected component

SPARE 3
TCU IGN COIL

IG2

WIPER FRT DR LOCK SPARE 4
S/HEATER SPARE 5

ROOM LP 1

AUDIO

TAIL LP LH

TAIL LP RH

START H/LP RH P/WDW LH P/WDW RH

HTD MIRR

A/CON BLOWER

56

10A 15A 15A

10A

25A 20A 25A 15A 10A

10A

20A

10A

10A

10A 10A 25A 25A

10A

10A 10A

Not Used Vehicle Speed Sensor, Transaxle Range Switch Ignition Coil #1~#4, Condenser Power Window Relay, A/C Control Module, Instrument Cluster (MICOM) BCM, Sunroof Motor, E/R Fuse & Relay Box (Blower Relay) Multifunction Switch (Wiper), Front Wiper Motor Door Lock/Unlock Relay, Two Turn Unlock Relay Driver Door Lock Actuator Not Used Driver/Passenger Seat Heater Module Not Used Instrument Cluster (IND.,ILL.), Tire Pressure Monitoring Module, BCM A/C Control Module, Luggage Room Lamp, Trunk Room Lamp Center Room Lamp, Overhead Console Lamp, Map Lamp Audio Rear Combination Lamp LH, Head Lamp LH, Front Turn Signal Lamp LH License Lamp LH/RH (4Door), License Lamp (5Door) Head Lamp RH, Rear Combination Lamp RH, Rheostat, Audio Front Turn Signal Lamp RH, Hazard Switch, Instrument Cluster (ILL.+) AUX & USB Jack, ESC Off Switch, A/C Switch, ECO Switch Multifunction Switch (Remote Control), A/C Control Module Rear Defogger Switch, Front Deicer Switch, ATM Shift Lever Switch ILL. Transaxle Range Switch, Ignition Lock Switch Instrument Cluster (High Beam IND.), Head Lamp RH Power Window Main Switch, Rear Power Window Switch LH Power Window Main Switch, Rear Power Window Switch RHPassenger Power Window Switch ECM, PCM, Rear Defogger Switch, Driver Power Outside Mirror Passenger Power Outside Mirror A/C Control Module (Auto A/C) ECM, PCM, Blower Switch, Blower Resistor A/C Control Module (Manual A/C)

Maintenance

Engine compartment main fuse panel

Description MDPS BLOWER RR HTD ABS 2
ABS 1

MULTI FUSE

ALT

B+1

IG2
IG1
ECU 1
C/FAN B+2
HORN F/PUMP A/CON INJECTOR

SENSOR

ECU 2

B/UP LP

WIPER

FUSE

Fuse rating

Protected component

80A 40A 40A 40A 40A

125A

50A

50A 40A 30A 30A 50A 10A 10A 10A 15A

10A

10A

10A

10A

EPS Control Module Blower Relay I/P Junction Box (Rear Defogger Relay) ABS Control Module, ESC Control Module ABS Control Module, ESC Control Module, Multipurpose Check Connector Alternator, E/R Fuse & Relay Box (Multi Fuse : ABS 1, ABS 2, MDPS, RR HTD, BLOWER, Fuse : A/CON) I/P Junction Box (Power Connector Fuse : ROOM LP 1, AUDIO, Fuse : FOG LP FRT, ROOM LP 2, STOP LP, Relay : Tail Lamp) Start Relay, Ignition Switch Ignition Switch Fuse : ECU 2, Engine Control Relay Cooling Fan (High) Relay, Cooling Fan (Low) Relay I/P Junction Box (Fuse : S/HEATER, SUNROOF, DR LOCK, HAZARD, Relay : Power Window) Horn Relay Fuel Pump Relay A/CON Relay ECM, PCM, Oil Control Valve #1/#2, Oxygen Sensor (Up)/(Down), Fuel Pump Relay ECM, PCM, Canister Purge Control Solenoid Valve, Variable Intake Solenoid Valve, Canister Close Valve, Immobilizer Module, A/CON Relay Cooling Fan (High) Relay, Cooling Fan (Low) Relay ECM, PCM PCM, Transaxle Range Switch, Instrument Cluster, Rear Combination Lamp LH/RH, ATM Shift Lever Switch ILL. ECM, PCM, Multifunction Switch (Wiper), Front Wiper Motor

7 57

CAUTION

If you don’t have necessary tools, the correct bulbs and the expertise, consult an authorized HYUNDAI dealer.In many cases,it is difficult to replace vehicle light bulbs because other parts of the vehicle must be removed before you can get to the bulb. This is especially true if you have to remove the head- light assembly to get to the bulb(s). Removing/installing the headlight assembly can result in damage to the vehicle.

✽✽ NOTICE After heavy, driving rain or washing, headlight and taillight lenses could appear frosty. This condition is caused by the temperature difference between the lamp inside and outside. This is similar to the condensation on your windows inside your vehicle during the rain and doesn’t indicate a problem with your vehicle. If the water leaks into the lamp bulb circuitry, have the vehicle checked by an authorized HYUNDAI dealer.

Maintenance

LIGHT BULBS

WARNING - Working on

the lights

Prior to working on the light, firmly apply the parking brake, ensure that the ignition switch is turned to the LOCK position and turn off the lights to avoid sudden movement of the vehicle and burning your fin- gers or receiving an electric shock.

Use only bulbs of the specified wattage.

CAUTION

Be sure to replace the burned-out bulb with one of the same wattage rating. Otherwise, it may cause damage to the fuse or electric wiring system.

58

ORB070025
Headlight, position light, turn sig- nal light, side marker light and front fog light bulb replacement (1) Headlight (High/Low) (2) Front turn signal light / Position light (3) Side marker (4) Front fog light (if equipped)

Maintenance

✽✽ NOTICE If the headlight aiming adjustment is necessary after the headlight assembly is reinstalled, consult an authorized HYUNDAI dealer.

ORB071048N

Headlight / Side marker 1. Open the hood. 2. Remove the headlight bulb cover by

turning it counterclockwise.

3. Disconnect the headlight bulb socket-

connector.

4. Unsnap the headlight bulb retaining wire by depressing the end and push- ing it upward.

5. Remove the bulb from the headlight

assembly.

6. Install a new headlight bulb and snap the headlight bulb retaining wire into position by aligning the wire with the groove on the bulb.

7. Connect the headlight bulb socket-

8. Install the headlight bulb cover by turn-

connector.

ing it clockwise.

7 59

(Continued) (cid:129) If a bulb becomes damaged or cracked, replace it immediately and carefully dispose of it.

(cid:129) Wear eye protection when chang- ing a bulb. Allow the bulb to cool down before handling it.

Maintenance

OHD076046

WARNING - Halogen bulbs (cid:129) Halogen bulbs contain pressur- ized gas that will produce flying pieces of glass if broken.

(cid:129) Always handle them carefully, and avoid scratches and abra- sions. If the bulbs are lit, avoid contact with liquids. Never touch the glass with bare hands. Residual oil may cause the bulb to overheat and burst when lit. A bulb should be operated only when installed in a headlight.

(Continued)

60

ORBC070049

Turn signal light/Position light 1. Turn off the engine and open the hood. 2. Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.

3. Remove the bulb from the socket by pressing it in and rotating it counter- clockwise until the tabs on the bulb align with the slots in the socket. Pull the bulb out of the socket

4. Insert a new bulb by inserting it into the socket and rotating it until it locks into place.

5. Install the socket in the assembly by aligning the tabs on the socket with the slots in the assembly. Push the socket into the assembly and turn the socket clockwise.

4. Remove the bulb-socket from the housing by turning the socket counter clockwise until the tabs on the socket align with the slots on the housing.

5. Install the new bulb-socket into the housing by aligning the tabs on the socket with the slots in the housing. Push the socket into the housing and turn the socket clockwise.

6. Connect the power connector to the

socket.

7. Reinstall the front bumper under cover.

ORBC070030

ORBC070031

Front fog light bulbs (if equipped) 1. Remove the front bumper under cover. 2. Reach your hand into the back of the

front bumper.

3. Disconnect the power connector from

the socket.

Maintenance

ORB070068

Side repeater light bulb replace- ment (if equipped) Type A 1. Remove the light assembly from the vehicle by prying the lens and pulling the assembly out.

2. Disconnect the bulb electrical connec-

tor.

3. Separate the socket and the lens parts by turning the socket counterclockwise until the tabs on the socket align with the slots on the lens part.

7 61

Maintenance

4. Remove the bulb by pulling it straight

out.

5. Insert a new bulb in the socket. 6. Reassemble the socket and the lens

part.

7. Connect the bulb electrical connector. 8. Reinstall the light assembly to the

body of the vehicle.

62

ORB070054

ORBC070033

Type B If the light bulb does not operate, have the vehicle checked by an authorized HYUNDAI dealer.

Rear combination light bulb replacement (4 Door) (1) Stop and tail light (2) Rear turn signal light (3) Back-up light (4) Side marker

Maintenance

ORB071033

Rear combination light bulb replacement (5 Door) (1) Tail light (2) Rear turn signal light (3) Back-up light (4) Stop and tail light (5) Side marker

7 63

ORBC070034

1. Open the trunk lid. 2. Remove the service cover by pulling

out the service cover.

ORB071051N 3. Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.

4. Remove the bulb from the socket by pressing it in and rotating it counter- clockwise until the tabs on the bulb