2005 Hyundai Accent Owners Manual

15

G140A01A-AAT Keeping the Condenser Clean

The air conditioner condenser (and engine ra- diator) should be checked periodically for accu- mulation of dirt, dead insects, leaves, etc. These can interfere with maximum cooling efficiency. When removing such accumulations, brush or hose them away carefully to avoid bending the cooling fans.

WARNING:

Use caution when handling brake fluid. It can damage your vision if you get it in your eyes. It will also damage your vehicles paint if spilled on it and not removed immediately.

HLC5036
The clutch fluid level in the master cylinder should be checked when performing other un- der hood services. The system should be checked for leakage at the same time. Check to make certain that the clutch fluid level is between the "MAX" and "MIN" level markings on the fluid reservoir. Fill as required. Fluid loss indicates a leak in the clutch system which should be inspected and repaired immediately. Consult your Hyundai dealer.

6 DO-IT-YOURSELF MAINTENANCE 16

G140B01A-AAT Checking the Air Conditioner Opera- tion

1. Start the engine and let it run at fast idle for several minutes with the air conditioner set at the maximum cold setting. If the air coming out of the in-dash vents is not cold, have the air conditioning system inspected by your Hyundai dealer.

2.

CAUTION:

Running the air conditioning system for ex- tended periods of time with a low refrigerant level may damage the compressor.

G140C01A-AAT Lubrication

To lubricate the compressor and the seals in the system, the air conditioner should be run for at least 10 minutes each week. This is particularly important during cool weather when the air con- ditioning system is not otherwise in use.

G140D02A-AAT Checking the Compressor Drive Belt

A/C

0.315 in. (8mm)

TENSION PULLEY

CRANK PULLEY

G140D01A

When the air conditioning is being used regular- ly, the compressor drive belt tension should be checked at least once a month with the engine turned off. To check the drive belt tension, press down on the belt halfway between the engine crankshaft and compressor pulleys. Pressing with your finger, you should not be able to deflect this belt anymore than 1/3 of an inch. If the belt is too loose, have it adjusted by your Hyundai dealer.

CHANGING THE AIR CONDITIONER FILTER B145A02A-GAT (For Evaporator and Blower Unit) (If Installed)

The air conditioner filter is located in front of the evaporator unit behind the glove box. It helps to decrease the amount of pollutants entering the car.

(2)

(1)

HLC2096

1. Open the glove box and by pushing at the outside of adjusting pin (1) first and then sliding the adjusting pin (2) in makes it easier to remove adjusting pin.

DO-IT-YOURSELF MAINTENANCE

CHECKING THE FREE-PLAY

17

3. Remove the filter cover by pushing the upper

end of the filter cover.

G150A01A-AAT Steering Wheel

2. Remove the cable and the wiring from the

filter cover.

HLC2097

4. Replace the two filters. 5.

Installation is the reverse order of disassem- bly.

HLC2099

CAUTION:

Be sure to install the air conditioner filter in the direction of the arrow sign. Otherwise, it may cause noise or deterioration.

HLC2098

1.18 in. (30 mm)

HLC5008

To check the steering wheel free-play, stop the car with the wheels pointed straight ahead and gently move the steering wheel back and forth. Use very light finger pressure and be sensitive to changes in resistance that mark the limits of the free-play. If the free-play is greater than specified, have it inspected by your Hyundai dealer and adjusted or repaired if necessary.

6 DO-IT-YOURSELF MAINTENANCE 18

G160A01A-AAT Clutch Pedal

G170A01A-AAT Brake Pedal

CHECKING BRAKE PEDAL CLEARANCE

G180A01A-AAT

0.24 ~ 0.51 in. (6 ~ 13 mm)

0.12 ~ 0.31 in. (3 ~ 8 mm)

1.78 in. (45.1 mm)

G180A01L

G160A01E With the engine off, press lightly on the clutch pedal until you feel a change in resistance. This is the clutch pedal free-play. The free-play should be within the limits specified in the illustration below. If it is not, have it inspected by your Hyundai dealer and adjusted or repaired if nec- essary.

HXGS508

With the engine off, press down on the brake pedal several times to reduce the vacuum in the brake booster. Then, using your hand, press down slowly on the brake pedal until you feel a change in resis- tance. This is the brake pedal free-play. The free-play should be within the limits speci- fied in the illustration above. If it is not, have it inspected by your Hyundai dealer and adjusted or repaired if necessary.

You need a helper to check the brake pedal clearance. With the engine running, have your helper press down on the brake pedal several times and then hold it down with a force of about 110 lbs (50 kg, 490 N). The brake pedal clear- ance is the distance from the top surface of the brake pedal to the asphalt sheeting under the floor mat. If the brake pedal clearance is not within the limits specified in the illustration, have it in- spected by your Hyundai dealer and adjusted or repaired if necessary.

DO-IT-YOURSELF MAINTENANCE

19

CAUTION:

When replacing a fusible link, never use anything but a new fusible link with the same or lower amperage rating. Never use a piece of wire or a higher-rated fusible link. This could result in serious damage and create a fire hazard.

CHECKING DRIVE BELTS

G190A01A-AAT

Water Pump Pulley

CHECKING AND REPLACING FUSES G200A01A-AAT Replacing a Fusible Link

0.2~0.24 in. (5.1~6 mm)

Alternator Pulley

Open- Replace

Good

Crankshaft Pulley

HTB186

Drive belts should be checked periodically for proper tension and adjusted if necessary. At the same time, belts should be examined for cracks, wear, fraying or other evidence of deterioration and replaced if necessary. Belt routing should also be checked to be sure there is no interference between the belts and other parts of the engine. After a belt is replaced, the new belt should be adjusted again after two or three weeks to eliminate slack resulting from initial stretching after use.

G200A01A A fusible link will melt if the electrical circuits from the battery are ever overloaded, thus pre- venting damage to the entire wiring harness. (This could be caused by a short in the system drawing too much current.) If this ever happens, have a Hyundai dealer determine the cause, repair the system and replace the fusible link. The fusible links are located in a relay box for easy inspection.

6 DO-IT-YOURSELF MAINTENANCE 20

G200B01A-AAT Replacing Accessory Fuses

1. Turn off the ignition and all other switches. 2. Open the fuse box and examine each fuse. Remove each fuse by pulling it toward you (a small "fuse puller" tool is contained in the fuse box to simplify this operation).

3. Be sure to check all other fuses even if you

find one that appears to have opened.

HLC4002

The fuse box for the lights and other electrical accessories will be found low on the dashboard on the driver's side. Inside the box you will find a list showing the circuits protected by each fuse. If any of your car's lights or other electrical accessories stop working, a blown (open) fuse could be the reason. If the fuse has opened, you will see that the metal strip inside the fuse has melted through. If you suspect a blown fuse, follow this procedure:

HLC4003

4. Replace the blown fuse by pressing a new fuse of the same rating into place. The fuse should be a snug fit. If it is not, have the fuse clip repaired or replaced by a Hyundai deal- er. If you do not have a spare fuse, you may be able to borrow a fuse of the same or lower rating from an accessory you can tempo- rarily get along without (the radio or cigarette lighter, for example). Always remember to replace the borrowed fuse.

Good

Open - Replace

G200B02L

CAUTION:

An open fuse indicates that there is a prob- lem in the electrical circuit. If you replace a fuse and it blows as soon as the accessory is turned on, the problem is serious and should be referred to a Hyundai dealer for diagnosis and repair. Never replace a fuse with anything except a fuse with the same or a lower amperage rating. A higher capacity fuse could cause damage and create a fire hazard.

NOTE: See page 6-32 for the fuse panel descrip- tions.

CHECKING THE BATTERY

G210A01A-AAT

D010B01A

WARNING:

When working with batteries, carefully ob- serve the following precautions to avoid se- rious injuries.

The fluid in the battery contains a strong solution of sulfuric acid, which is poisonous and highly corrosive. Be careful not to spill it on yourself or the car. If you do spill battery fluid on yourself, immediately do the following:

o If battery fluid is on your skin, flush the affected areas with water for at least 15
minutes and then seek medical assistance. o If battery fluid is in your eyes, rinse out your eyes with water and get medical assistance as soon as possible. While you are being driven to get medical assistance, continue to rinse your eyes by using a sponge or soft cloth saturated with water.

o If you swallow battery fluid, drink a large quantity of water or milk followed by milk of magnesia, eat a raw egg or drink vegetable oil. Get medical assistance as soon as pos- sible.

While batteries are being charged (either by a battery charger or by the vehicle's alternator), they produce explosive gases. Always observe these warnings to prevent injuries from occur- ring: o Charge batteries only in a well ventilated

o Do not permit flames, sparks or smoking in

area.

the area.

o Keep children away from the area.

DO-IT-YOURSELF MAINTENANCE

21

G210B02A-AAT Checking the Battery

Keep the battery clean. Any evidence of corro- sion around the battery posts or terminals should be removed using a solution of household bak- ing soda and warm water. After the battery terminals are dry, cover them with a light coating of grease.

WARNING:

Always read the following instruc- tions carefully when handling a battery. Keep lighted cigarettes and all other flames or sparks away from the battery. Hydrogen, which is a highly com- bustible gas, is always present in battery cells and may explode if ignited. Keep batteries out of the reach of children because batteries con- tain highly corrosive SULFURIC ACID. Do not allow battery acid to contact your skin, eyes, clothing or paint finish.

6 DO-IT-YOURSELF MAINTENANCE 22

CHECKING ELECTRIC COOLING FANS G220A01A-AAT

POWER STEERING FLUID LEVEL

G230A03A-AAT

If any electrolyte gets into your eyes, flush your eyes with clean water for at least 15 minutes and get immediate medical attention. If possible, continue to apply wa- ter with a sponge or cloth until medical attention is received. If electrolyte gets on your skin, thoroughly wash the contacted area. If you feel a pain or a burning sensation, get medical attention immediately. Wear eye protection when charg- ing or working near a battery. Always provide ventilation when working in an enclosed space.

o When lifting a plastic-cased battery, ex- cessive pressure on the case may cause battery acid to leak, resulting in personal injury. Lift with a battery carrier or with your hands on opposite corners.

o Never attempt to charge the battery when

the battery cables are connected.

o The electrical ignition system works with

high voltage. Never touch these components with the engine running or the ignition switched on.

WARNING:

The radiator fan is controlled by engine cool- ant temperature and may sometimes operate even when the engine is not running. Use extreme caution when working near the blades of the cooling fan, so that you are not injured by a rotating fan blade. As the cool- ant temperature decreases the fan will auto- matically shut off. This is a normal condition.

G220B01A-AAT Checking Engine Cooling Fan

The engine cooling fan should come on auto- matically if the engine coolant temperature is high.

G220C01A-AAT Checking Condenser Cooling Fan

The condenser cooling fan should come on automatically whenever the air conditioner is in operation.

HLC5006
The power steering fluid level should be checked regularly. To check the power steering fluid level, be sure the engine is "OFF", then check to make certain that the power steering fluid level is between the "MAX" and "MIN" level markings on the fluid reservoir.

NOTE: Grinding noise from the power steering pump may be heard immediately after the engine is started in extremely cold conditions (below -4°F). If the noise stops during warm up, there is no abnormal function in the system. It is due to a power steering fluid character- istic in extremely cold conditions.

Recommended Fluid Use PSF-3 type fluid

NOTE: Do not start the engine when the power steering oil reservoir is empty.

G240A01A-AAT POWER STEERING HOSES

It is suggested that you check the power steer- ing hose connections for fluid leakage at those intervals specified in the vehicle maintenance schedule in Section 5. The power steering hoses should be replaced if there is severe surface cracking, pulling, scuff- ing or worn spots. Deterioration of the hose could cause premature failure.

DO-IT-YOURSELF MAINTENANCE

HEADLIGHT AIMING ADJUSTMENT

23

G250A01A-AAT FOR MORE INFORMATION ABOUT YOUR HYUNDAI

G290A04A-AAT Before performing aiming adjustment, make sure of the following.

If you desire additional information about main- taining and servicing your Hyundai, you may purchase a factory Shop Manual at your Hyundai dealer's parts department. This is the same manual used by dealership technicians and while it is highly technical it can be useful in obtaining a better understanding of your car and how it works.

1. Keep all tires inflated to the correct pressure. 2. Place the vehicle on level ground and press the front bumper & rear bumper down sever- al times. Place vehicle at a distance of 118
in. (3m) from the test wall.

3. See that the vehicle is unloaded (except for full levels of coolant, engine oil and fuel, and spare tire, jack, and tools). Have the driver or equivalent weight placed in driver's seat.

4. Clean the headlight lenses and turn on the

headlights (Low beam).

5. Open the hood.

Vertical Aiming

G290A01A-1

6 DO-IT-YOURSELF MAINTENANCE 24

6. Draw the vertical line (through the center of each headlight) and the horizontal line (through the center of each headlight) on the aiming screen. And then, draw a parallel line at 0.8 in.(21
mm) under the horizontal line.

7. Adjust each cut-off line of the low beam to

the parallel line with a phillips screwdriver - VERTICAL AIMING

WARNING:

Horizontal aiming should be adjusted by an authorized Hyundai dealer.

SPECIFICATIONS:

"H"; Horizontal center line of headlights from ground : 25.8 in. (656 mm)

"W"; Distance between each headlight center : 42.4 in. (1,078 mm)

"L"; Distance between the headlights and the wall that the lights are tested against: 118 in. (3,000 mm).

G290B02A-AAT Adjustment After Headlight Assembly Replacement

0.8 in. (21mm)

Vertical line

Horizontal line

"P"

Ground line

G290B01A-2

Cut-off line

If the vehicle has had front body repair and the headlight assembly has been replaced, the head- light aiming should be checked using an aiming screen as shown in the illustration. Turn on the headlight switch. (Low Beam Position)

1. Adjust headlights so that main axis of light is parallel to center line of the body and is aligned with point "P" shown in the illustra- tion.

2. Dotted lines in the illustration show the cen-

ter of headlights.

REPLACEMENT OF LIGHT BULBS

G260A02A-AAT Before attempting to replace a light bulb, be sure the switch is turned to the "OFF" position. The next paragraph shows how to reach the light bulbs so they may be changed. Be sure to replace the burned-out bulb with one of the same number and wattage rating. See page 6-31 for the wattage descriptions

G270A03A-AAT Headlight Bulb

1. Allow the bulb to cool. Wear eye protection. 2. Open the engine hood. 3. Always grasp the bulb by its plastic base,

avoid touching the glass.

DO-IT-YOURSELF MAINTENANCE

25

CAUTION:

Keep the lamps out of contact with petro- leum products, such as oil, gasoline, etc.

4. Using a socket wrench of the correct size, remove the headlight assembly mounting bolts.

HLC5033

HLC5034-1
5. Disconnect the power cord from the bulb

base in the back of the headlight.

6. Remove the dust cover.

HLC5009

6 DO-IT-YOURSELF MAINTENANCE 26

7. Push the bulb spring to remove the headlight

bulb.

HLC5010

HLC5011

G270A03O

8. Remove the protective cap from the replace- ment bulb and install the new bulb by match- ing the plastic base with the headlight hole. Re-attach the bulb spring and install the dust cover. Reconnect the power cord.

9. Use the protective cap and carton to dispose

of the old bulb.

10.Check for proper headlight aim.

WARNING:

The halogen bulb contains gas under pres- sure and if impacted could shatter, resulting in flying fragments. Always wear eye protec- tion when servicing the bulb. Protect the bulb against abrasions or scratches and against liquids when lighted. Turn the bulb on only when installed in a headlight. Re- place the headlight if damaged or cracked. Keep the bulb out of the reach of children and dispose of the used bulb with care.

G270B01A-GAT Front Turn Signal light / Position Light

(2)

(1)

G270D01TB-AAT Rear Combination Light 4 Door

DO-IT-YOURSELF MAINTENANCE

27

HLC5034
1. Disconnect the power cord from the bulb.

HLC5012

2. To replace the front turn signal light (1) or position light (2), take it out from the bulb holder by turning it counterclockwise. Install the new bulb.

3.

3 Door

G270D01A

1. Open the trunk lid/tail gate.

HLC5015

6 DO-IT-YOURSELF MAINTENANCE 28

2. Remove the mounting screws as shown with

a phillips screwdriver.

4 Door

3. To replace the rear combination light (stop/ tail light, turn signal light or back-up light), take it out from the bulb holder by turning it counterclockwise.

G270C01TB-AAT Luggage Compartment Light (If Installed) 3 Door

4 Door

(1) Stop/Tail Light (2) Turn Signal Light (3) Back-up Light

4.

Install the new bulb.

3 Door

(2)

(3)

(1)

(3)

(1)

(2)

G270D02A

HLC5016

1. Remove the cover with a flat-head screw-

driver.

HLC5014

G270G01A-AAT Interior Light (Map Light) (If Installed)

DO-IT-YOURSELF MAINTENANCE

29

2. Disconnect the power cord.

HTB283

HLC5017

2. Replace with a new bulb.

HLC5018

1. Remove the cover with a flat-head screw-

driver.

3. Replace with a new bulb.

HTB284

6 DO-IT-YOURSELF MAINTENANCE 30

G270H01A-AAT Interior Light

HLC5019

2. Replace with a new bulb.

HLC5020

1. Remove the cover with a flat-head screw-

driver.

BULB WATTAGES

G280A03A-AAT

4 DOOR

3 DOOR

DO-IT-YOURSELF MAINTENANCE

31

12

10

11

11

10

12

G280A02A

No.

Part Name

Front Position Light Headlight (High/Low) Front Turn Signal Light Interior Light (Map Light) (If Installed) Interior Light Front Fog Light (If Installed) Front Side Marker Light

Wattage

60/55

27
10
10
27

No.

10
11
12

Part Name

Rear Combination Light

Turn Signal Light Stop/Tail Light Back-up Light

High Mounted Rear Stop Light (If Installed) Rear Side Marker Light Luggage Compartment Light (If Installed) License Plate Light

Wattage

27

27/8(4 Door), 28/8(3 Door)

17
17

6 DO-IT-YOURSELF MAINTENANCE 32

FUSE PANEL DESCRIPTION

G200C02A-GAT Engine Compartment

DESCRIPTION ALT

FUSIBLE

LINK

BATTERY

LAMP ECU IGN

RAD FAN BLOWER

ABS ABS

P/WDW

COND FAN

FUSE RATING

PROTECTED COMPONENTS

120A 50A 50A 20A 30A 20A 30A 30A 30A 30A 20A

Charging (Generator) Fuse 6, 7, 8, 9, Horn fuse, Room lamp fuse Head lamp fuse, Front fog lamp fuse, Tail lamp relay, H/LP washer fuse Engine control relay, Generator, Fuel pump relay, ECU #3 fuse Ignition power source, Start relay Radiator fan control Blower control ABS control, ABS bleeding connector ABS control, ABS bleeding connector Power window Condenser fan control

NOTE: Not all fuse panel descriptions in this manual may be applicable to your vehicle. It is accurate at the time of printing. When you inspect the fuse box on your vehicle, refer to the fuse box label.

HLC5027

DESCRIPTION

FUSE RATING

PROTECTED COMPONENTS

DO-IT-YOURSELF MAINTENANCE

33

ECU #1

A/CON COMP

HORN

TAIL LH

TAIL RH H/LP LH H/LP RH

FRONT FOG

ROOM LP

AUDIO

ECU #2

ECU#3

FUSE

H/L WASHER F/PUMP CHK (E50)

10A

10A 10A

10A

10A 10A 10A 15A

10A

15A

15A

10A 25A

Radiator fan, Condenser fan, ECM, Oxygen sensor, Purge control valve, SMATRA, Glow plug relay, Heater relay, Stop lamp switch A/C relay Horn relay Illumination lamps, Left rear combination lamp, License lamp, DRL control, Position lamp, H/LP washer relay Right rear combination lamp, License lamp, Position lamp Left head lamp, DRL control, Instrument cluster Right head lamp Front fog lamp relay Instrument cluster, Courtesy lamp, Trunk room lamp, ETACM, DLC, Door warning, Multipurpose check connector Audio, Digital clock, Power antenna, A/C switch, Rear fog lamp switch Idle speed actuator, ECM, Camshaft position sensor, EGR actuator, Throttle plate actuator ECM Head lamp washer motor Fuel pump relay, Fuel pump motor

6 DO-IT-YOURSELF MAINTENANCE 34

G200E01A-GAT Inner Panel

FUSE

FUSE RATING

PROTECTED COMPONENTS

10

11
12
13
14
15
16
17
18

10A

10A 10A 15A

10A

10A 10A 10A 20A

10A

20A 20A 10A 10A 15A 10A 10A 20A

Hazard warning, Back-up lamp switch, Transaxle range switch, A/T shift & key lock control module ETACM, Pre-Excitation resistor, Instrument cluster, Seat belt timer Instrument cluster Air bag ECM, A/T shift lever, Transaxle range switch, Mass air flow sensor, Vehicle speed sensor, Water sensor Power door lock Hazard warning, ETACM Stop lamp, A/T shift lever, A/T key interlock solenoid Rear window defogger Head lamp, Power window, Head lamp leveling, Head lamp washer, ETACM, Front fog lamp, Blower control, Rear intermittent washer, Fuel filter relay Front wiper & washer Seat warmer ABS control, ABS bleeding Digital clock, Audio, A/T shift & key lock control module Cigarette lighter Power outside mirror Rear window & outside mirror defogger Rear wiper

HLC5031

EMISSION CONTROL SYSTEMS

Emission Control System ............................................. 7-2
Catalytic Converter ....................................................... 7-3

7 EMISSION CONTROL SYSTEMS

EMISSION CONTROL SYSTEM

H010A01A-AAT Your Hyundai is equipped with an emission control system to meet all requirements of the U.S. Environmental Protection Agency or Cali- fornia Air Resources Board. There are three emission control systems which are as follows.

1) Crankcase Emission Control System 2) Evaporative Emission Control System 3) Exhaust Emission Control System

In order to ensure the proper function of the emission control systems, it is recommended that you have your car inspected and main- tained by an authorized Hyundai dealer in accordance with the maintenance schedule in this manual.

H010B01A-AAT 1. CRANKCASE EMISSION CONTROL

SYSTEM

The positive crankcase ventilation system is employed to prevent air pollution caused by blow-by gases being emitted from the crank- case. This system supplies filtered fresh air to the crankcase through the air intake hose. Inside the crankcase, the fresh air mixes with blow-by gases, then passes through the PCV valve into the induction system.

H010C01S-AAT 2. Evaporative Emission Control (Includ- ing ORVR: Onboard Refueling Vapor Recovery) System

The Evaporative Emission Control System is designed to prevent fuel vapors from escaping into the atmosphere. (The ORVR system is designed to allow the vapors from the fuel tank to be loaded into a canister while refueling at the gas station, preventing the escape of fuel vapors into the atmosphere.)

Canister

Fuel vapors generated inside the fuel tank are absorbed and stored in the onboard canister. When the engine is running, the fuel vapors absorbed in the canister are drawn into the induction system through the purge control solenoid valve.

Purge Control Solenoid Valve (PCSV)

The purge control solenoid valve is controlled by the Engine Control Module (ECM); when the engine coolant temperature is low during idling, the PCSV closes so that evaporated fuel is not taken into the engine. After the engine warms-up during ordinary driving, the PCSV opens to introduce evaporated fuel to the engine.

H010D01A-AAT 3. EXHAUST EMISSION

CONTROL SYSTEM

The Exhaust Emission Control System is a highly effective system which controls ex- haust emissions while maintaining good ve- hicle performace.

EMISSION CONTROL SYSTEMS

system.

WARNING:

o Remember that your Hyundai dealer is

your best source of assistance.

o Do not stop your Hyundai over any combustible material such as grass, paper, leaves or rags. These materials might contact the hot catalytic con- verter and a fire might result.

CATALYTIC CONVERTER

H020A01A-AAT

Catalytic Converter

HLC5022

All Hyundai vehicles are equipped with a mono- lith type three-way catalytic converter to reduce the carbon monoxide, hydrocarbons and nitrogen oxides contained in the exhaust gas. Exhaust gases passing through the cata- lytic converter cause it to operate at a very high temperature. The introduction of large amounts of unburned gasoline into the ex- haust may cause the catalytic converter to overheat and create a fire hazard. This risk may be reduced by observing the following:

WARNING:

o Use unleaded fuel only. o Maintain the engine in good operating condition. Extremely high catalytic con- verter temperatures can result from im- proper operation of the electrical, igni- tion or multiport electronic fuel injec- tion.

o If your engine stalls, pings, knocks, or is hard to start, have your Hyundai dealer inspect and repair the problem as soon as possible.

o Avoid driving with a very low fuel level. Running out of gasoline may cause the engine to misfire and result in damage to the catalytic converter.

o Avoid idling the engine for periods

longer than 10 minutes.

o The vehicle should not be pushed or pulled to get started. This may cause the catalytic converter to overheat and create a fire hazard.

o Do not touch the catalytic converter or any other part of the exhaust system while the catalytic converter is hot. Shut off the engine, wait for at least one hour before touching the catalytic con- verter or any other part of the exhaust

CONSUMER INFORMATION, REPORTING

SAFETY DEFECTS & BINDING

ARBITRATION OF WARRANTY CLAIMS

Vehicle Identification Number (VIN) ............................. 8-2
Engine Number ............................................................. 8-2
Recommended Cold Tire Inflation Pressures .............. 8-3
Snow Tires.................................................................... 8-9
Tire Chains ................................................................. 8-10
Tire Rotation ............................................................... 8-10
Tire Balancing ............................................................. 8-11
Tire Traction................................................................ 8-11
When to Replace Tires ............................................... 8-11
Spare Tire and Tools .................................................. 8-12
Warranties for Your Hyundai Vehicle ......................... 8-12
Consumer Information ................................................ 8-13
Reporting Safety Defects ........................................... 8-15
Binding Arbitration of Warranty Claims ...................... 8-16

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

ENGINE NUMBER

VEHICLE IDENTIFICATION NUMBER (VIN)

I010A02A-AAT

I010B01A-AAT

I010A01A-1
The vehicle identification number (VIN) is the number used in registering your car and in all legal matters pertaining to its ownership, etc. It can be found in four different places on your car:

The engine number is stamped on the engine block as shown in the drawing.

F040A02TB-1

TIRES

I020A02A-AAT TIRE INFORMATION The tires supplied on your new Hyndai are chosen to provide the best perfor- mance for normal driving. If you ever have questions about your tire warranty and where to obtain ser- vice, see the tire manufacture's book- let included with your vehicle's Owner's Manual Literature Kit.

1. On the bulkhead between the engine and

passenger compartments.

2. On the left top side of the instrument panel where it can be seen by looking down through the windshield. 3. Door edge post 4. On the lower side of the center pillar outer

panel.

I030A02JM-AAT

RECOMMENDED COLD TIRE INFLA- TION PRESSURES

I030A01A-2

Tire label located on the driver's side of the center pillar outer panel gives the cold tire pressures recommended for your vehicle with the original tire size, the number of people that can be in your vehicle and vehicle capacity weight.

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

WARNING:

Severe underinflation (10 psi (70
kPa) or more) can lead to severe heat buildup, causing blowouts, tread separation and other tire fail- ures that can result in the loss of vehicle control leading to severe injury or death. This risk is much higher on hot days and when driv- ing for protracted periods at high speeds.

I030A01LC-1

I030A01LC-2

These pressures were chosen to pro- vide the most satisfactory combina- tion of ride comfort, tire wear and stability under normal conditions. Tire pressures should be checked at least monthly. Proper tire inflation pressures should be maintained for these rea- sons:

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

NOTE: o Underinflation also results in ex- cessive wear, poor handling and reduced fuel economy. Wheel de- formation also is possible. Keep your tire pressures at the proper levels. If a tire frequently needs refilling, have it checked by your Hyundai Dealer.

o Overinflation produces a harsh ride, excessive wear at the center of the tire tread, and a greater possibility of damage from road hazards.

WARNING:

Overinflation or underinflation can reduce the tire life, adversely affect vehicle handling, and lead to sud- den tire failure. This could rusult in loss of vehicle control and potential injury.

CAUTION:

Always observe the following:

o Check pressures when the tires are cold. (After the vehicle has been parked for at least three hours or hasn't been driven more than one mile (1.6 km) since start- ing up.)

o Check the pressure of your spare tire each time you check the pres- sure of other tires.

o Never overload your vehicle. Be especially careful about overload- ing if you equip your vehicle with a luggage rack.

o Worn, old tires can cause acci- dents. If your tread is badly worn, or if your tires have been dam- aged, replace them.

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

I035A01JM-AAT

CHECKING TIRE INFLATION PRES- SURE Check your tires once a month or more. Also, check the tire pressure of the spare tire.

How to Check Use a good quality gage to check tire pressure. You can not tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they're underinflated. Check the tire's inflation pressure when the tires are cold. - "Cold" means your vehicle has been sitting for at least three hours or driven no more than 1
mile (1.6 km).

Remove the valve cap from the tire valve stem. Press the tire gage firmly onto the valve to get a pressure mea- surement. If the cold tire inflation pres- sure matches the recommended pres- sure on the tire and loading information label, no further adjustment is neces- sary. If the pressure is low, add air until you reach the recommended amount. If you overfill the tire, release air by pushing on the metal stem in the center of the tire valve. Recheck the tire pressure with the tire gage. Be sure to put the valve caps back on the valve stems. They help prevent leaks by keeping out dirt and moisture.

I030B01JM-AAT TIRE SIDEWALL LABELING

5, 6

I030B04JM

Federal law requires tire manufactur- ers to place standardized information on the sidewall of all tires. This infor- mation identifies and describes the fundamental characteristics of the tire and also provides the tire identification number (TIN) for safety standard cer- tification. The TIN can be used to identify the tire in case of a recall.

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

1. Manufacturer or Brand name

o Manufacturer or Brand name is

shown.

2. Tire size (example: P175/70R13)

o The "P" indicates the tire is de- signed for passenger vehicles. A "T" is the designation for a tempo- rary spare tire.

o Three-digit number (175): This number gives the width in millime- ters of the tire from sidewall edge to sidewall edge.

o Two-digit number (70): This num- ber, known as the aspect ratio, gives the tire's ratio of height to width.

o R: The "R" stands for radial. o Two-digit number (13): This num- ber is the wheel or rim diameter in inches.

o Two (or three) digit number (82): This number is the tire's load in- dex. It is a measurement of how much weight each tire can sup- port.

o T: Speed Rating. The speed rat- ing denotes the speed at which a tire is designed to be driven for extended periods of time. The ratings range from "A" to "Z" (98
to 186 MPH).

3. TIN (Tire Identification Number) for new tire (example: DOT XX XX XXX XXXX) o DOT: Abbreviation for the "De- partment of Transportation". The symbol can be placed above, be- low or to the left or right of the Tire Iden tification Number. In- dicates tire is in compliance with the U.S. Department of Transportation Motor Vehicle Safety Standards.

o 1st two-digit code: Manufacturer's

identification mark

o 2nd two-digit code: Tire size o 3rd three-digit code: Tire type code

(Optional)

o 4th four-digit code: Date of Manu-

facture

o Four numbers represent the week and year the tire was built. For example, the numbers 3104
means the 31st week of 2004.

4. Tire ply composition and mate-

rial The number of layers or plies of rubbercoated fabric in the tire. Tire manufacturers also must indicate the materials in the tire, which in- clude steel, nylon, polyester, and others. The letter "R" means radial ply construction; the letter "D" means diagonal or bias ply construction; and the letter "B" means belted-bias ply construction.

5. Maximum permissible inflation

pressure This number is the greatest amount of air pressure that should be put in the tire. Do not exceed the maxi- mum permissible inflation pressure. Refer to the Tire and Loading Infor- mation label for recommended infla- tion pressure.

6. Maximum load rating

This number indicates the maxi- mum load in kilograms and pounds that can be carried by the tire. When replacing the tires on the vehicle, always use a tire that has the same load rating as the factory installed tire.

7. Uniform Tire Quality Grading

(UTQG): Tire manufacturers are required to grade tires based on three perfor- mance factors: treadwear, traction and temperature resistance. For more information, see Uniform Tire Quality Grading on page 8-13.

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

I030D01JM-AAT

TIRE TERMINOLOGY AND DEFINI- TIONS Air Pressure: The amount of air inside the tire pressing outward on the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight: This means the combined weight of optional accesso- ries. Some examples of optional ac- cessories are, automatic transmission, power seats, and air conditioning. Aspect Ratio: The relationship of a tire's height to its width. Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread.

Cold Tire Pressure: The amount of air pressure in a tire, measured in pounds per square inch (psi) or kilopascals (kPa) before a tire has built up heat from driving. Curb Weight: This means the weight of a motor vehicle with standard and optional equipment including the maxi- mum capacity of fuel, oil and coolant, but without passengers and cargo. DOT Markings: A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation motor vehicle safety standards. The DOT code includes the Tire Identification Number (TIN), an alphanumeric desig- nator which can also identify the tire manufacturer, production plant, brand and date of production. GVWR: Gross Vehicle Weight Rating GAWR FRT: Gross Axle Weight Rat- ing for the front Axle. GAWR RR: Gross Axle Weight Rating for the rear axle.

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

Intended Outboard Sidewall: The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure. Load Index: An assigned number rang- ing from 1 to 279 that corresponds to the load carrying capacity of a tire. Maximum Inflation Pressure: The maximum air pressure to which a cold tire may be inflated. The maximum air pressure is molded onto the sidewall. Maximum Load Rating: The load rat- ing for a tire at the maximum permis- sible inflation pressure for that tire. Maximum Loaded Vehicle Weight: The sum of curb weight; accessory weight; vehicle capacity weight; and production options weight. Normal Occupant Weight: The num- ber of occupants a vehicle is designed to seat multiplied by 150 pounds (68
kg).

Occupant Distribution: Designated seating positions. Outward Facing Sidewall: The side of a asymmetrical tire that has a par- ticular side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering or bears manufacturer, brand and or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire. Passenger (P-Metric) Tire: A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inflation Pressure: Vehicle manufacturer's recommended tire inflation pressure and shown on the tire placard. Radial Ply tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim: A metal support for a tire and upon which the tire beads are seated.

Sidewall: The portion of a tire be- tween the tread and the bead. Speed Rating: An alphanumeric code assigned to a tire indicating the maxi- mum speed at which a tire can oper- ate. Traction: The friction between the tire and the road surface. The amount of grip provided. Tread: The portion of a tire that comes into contact with the road. Treadwear Indicators: Narrow bands, sometimes called "wear bars," that show across the tread of a tire when only 2/32 inch of tread remains. UTQGS: Uniform Tire Quality Grading Standards, a tire information system that provides consumers with ratings for a tire's traction, temperature and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire.

Vehicle Capacity Weight: The num- ber of designated seating positions multiplied by 150 lbs. (68 kg) plus the rated cargo and luggage load Vehicle Maximum Load on the Tire: Load on an individual tire due to curb and accessory weight plus maximum occupant and cargo weight. Vehicle Normal Load on the Tire: That load on an individual tire that is determined by distributing to each axle its share of the curb weight, accessory weight, and normal occupant weight and driving by 2. Vehicle Placard: A label permanently attached to a vehicle showing the origi- nal equipment tire size and recom- mended inflation pressure

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

I040A01O-AAT

SNOW TIRES If you equip your car with snow tires, they should be the same size and have the same load capacity as the original tires. Snow tires should be installed on all four wheels; otherwise, poor handling may result. Snow tires should carry 4 psi (28 kPa) more air pressure than the pressure recommended for the standard tires on the tire label on the driver's side of the center pillar , or up to the maximum pressure shown on the tire sidewall whichever is less. Do not drive faster than 75 mph (120
km/h) when your car is equipped with snow tires.

I040B01JM-AAT

ALL SEASON TIRES Hyundai specifies all season tires on some models to provide good perfor- mance for use all year round, including snowy and icy road conditions. All sea- son tires are identified by ALL SEA- SON and/or M+S (Mud and Snow) on the tire sidewall. Snow tires have better snow traction than all season tires an may be more appropriate in some ar- eas.

I040C01JM-AAT

SUMMER TIRES Hyundai specifies summer tires on some models to provide superior per- formance on dry roads. Summer tire performance is substantrally reduced in snow and ice. Summer tires do not have the tire traction rating M+S (Mud and Snow) on the tire side wall. if you plan to operate your vehicle in snowy or icy conditions. Hyundai recommends the use of snow tires or all season tires on all four wheels.

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS 10

I050A03A-AAT TIRE CHAINS

I060A02A-AAT

TIRE ROTATION

Tire chains, if necessary, should be installed on the front wheels. Be sure that the chains are installed in accordance with the manufacturer's instructions.

To minimize tire and chain wear, do not con- tinue to use tire chains when they are no longer needed.

WARNING:

o When driving on roads covered with snow or ice, drive at less than 20 mph (30 km/h). o Use the SAE "S" class or wire & plastic

chains.

o If you have noise caused by chains contacting the body, retighten the chain to avoid contact with the vehicle body. o To prevent body damage, retighten the

chains after driving 0.3~0.6 miles.

HEF-241

Tires should be rotated every 7,500
miles (12,000 km). If you notice that tires are wearing unevenly between rotations, have the car checked by a Hyundai dealer so the cause may be corrected. After rotating, adjust the tire pressures and be sure to check the wheel nut torque.

! WARNING:

o Do not use the temporary spare

tire for tire rotation.

o Do not mix bias ply and radial ply tires under any circumstances. This may cause unusual handling characteristics that could result in death, serious injury, or prop- erty damage.

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

11

I070A01A-AAT

TIRE BALANCING A tire that is out of balance may affect handling and tire wear. The tires on your Hyundai were balanced before the car was delivered but may need balancing again during the years you own the car. Whenever a tire is dismounted for repair, it should be rebalanced before being reinstalled on the car.

I080A01A-AAT

TIRE TRACTION Tire traction can be reduced if you drive on worn tires, tires that are im- properly inflated or on slippery road surfaces. Tires should be replaced when tread wear indicators appear. To reduce the possibility of losing control, slow down whenever there is rain, snow or ice on the road.

I090A01A-AAT

WHEN TO REPLACE TIRES

0.06 in. (1.6 mm)

Tread wear in- dicator

HGK248

The original tires on your car have tread wear indicators. The location of tread wear indicators is shown by the "TWI" or " " marks, etc., The tread wear indicators appear when the tread depth is 0.06 in. (1.6 mm). The tire should be replaced when these appear as a solid bar across two or more grooves of the tread. Always replace your tires with those of the recom- mended size. If you change wheels, the new wheel's rim width and offset must meet Hyundai specification.

! WARNING:

o Driving on worn-out tires is dan- gerous! Worn-out tires can cause loss of braking effectiveness, steering control and traction. When replacing tires, never mix radial and bias ply tires on the same car. If you replace radial tires with bias-ply tires, they must be installed in sets of four.

o Using tires and wheels of other than the recommended sizes could cause unusual handling characteristics that could cause death, serious injury, or property damage.

o Wheels that do not meet Hyundai's dimensional specifications may fit poorly and result in damage to the vehicle, including broken wheel studs.

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS 12

I100A02E-AAT

SPARE TIRE AND TOOLS

I110A01A-AAT SHOP MANUAL

A Hyundai Shop Manual is available from your authorized Hyundai dealer. It's written for pro- fessional technicians, but is simple enough for most mechanically-inclined owners to under- stand.

I100A01A

Your Hyundai is delivered with the following:

Spare tire and wheel Wheel nut wrench, Wrench bar Jack

WARRANTIES FOR YOUR HYUNDAI VEHICLE

I120A03A-AAT o New vehicle 60 Months/60,000 Miles Limited

Warranty.

o New vehicle 120 Months/100,000 Miles Lim- ited Powertrain Warranty (original owner only).

o Anti-Perforation Limited Warranty o Emission Defect Warranty - Federal Ve-

o California Emission Control System War-

ranty (if applicable)

o Emission Performance Warranty Federal

o Replacement Parts and Accessories Limited

hicle

vehicle

Warranty

NOTE: Detailed warranty information is provided in your Hyundai Owner's Handbook.

CONSUMER INFORMATION

I130A01A-AAT This consumer information has been prepared in accordance with regulations issued by the National Highway Traffic Safety Administration of the U.S. Department of Transportation. It provides the purchasers and/or prospective purchasers of Hyundai automobiles with infor- mation on uniform tire quality grading. Your Hyundai dealer will help answer any questions you may have as you read this information.

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

13

Traction AA, A, B, C - The traction grades, from highest to lowest, are AA, A, B, and C. Those grades repre- sent the tire's ability to stop on wet pavement as measured under con- trolled conditions on specified govern- ment test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.

WARNING:

The traction grade assigned to this tire is based on straight-ahead brak- ing traction tests, and does not in- clude acceleration, cornering, hy- droplaning, or peak traction charac- teristics.

I130B03A-AAT

Tire Quality Grading Department of Transportation quality grades - All passenger vehicle tires must conform to Federal Safety Stan- dards in addition to these grades. These quality grades are molded on the sidewall.

Treadwear - The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1 - 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road char- acteristics and climate.

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS 14

Temperature A, B, C - The tempera- ture grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under con- trolled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of perfor- mance on the laboratory test wheel than the minimum required by law.

! WARNING:

The temperature grade for this tire is established for a tire that is prop- erly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.

Uniform Tire Quality Grading - Qual- ity grades can be found on the tire sidewall between the tread shoulder and the maximum section width. For example: Treadwear 200 Traction AA Temperature A

I130D03A-AAT Hyundai motor vehicles are designed and manufactured to meet or exceed all applicable safety standards.

For your safety, however, we strongly urge you to read and follow all directions in this Owner's Manual, particularly the information under the headings "NOTE", "CAUTION" and "WARNING".

If, after reading this manual, you have any questions regarding the operation of your vehi- cle, please contact your nearest Hyundai Motor America Regional Office as listed below:

Eastern Region : Connecticut, Delaware, Maine, Maryland, Massachusetts, New Hampshire, New Jersey, New York, Pennsylvanina, Rhode Is- land, Vermont, Virginia, West Virginia.

Eastern Region 1100 Cranbury South River Road Jamesburg, NJ 08831
(800) 633-5151

8
15

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-888-327-4236 or write to: NHTSA, U.S. Department of Transportation, Washington. D.C. 20590. You can also obtain other information about motor vehicle safety from the Hotline.

REPORTING SAFETY DEFECTS

I130C02A-AAT If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National High- way Traffic Safety Administration (NHTSA) in addition to notifying HYUNDAI MOTOR AMERICA. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. How- ever, NHTSA cannot become involved in individual problems between you, your dealer, or HYUNDAI MOTOR AMERICA.

Southern Region: Alabama, Arkansas, Flor- ida, Georgia, Louisiana, Mississippi, North Caro- lina, South Carolina, Oklahoma, Tennessee, Texas.

Southern Region 270 Riverside Parkway, Suite A Austell, GA 30168
(800) 633-5151

Central Region: Illinois, Indiana, Missouri, lowa, Kansas, Kentucky, Michigan, Minne- sota, Nebraska, North Dakota, South Dakota, Ohio, Wisconsin.

Central Region 1705 Sequoia Drive Aurora, Illinois 60506
(800) 633-5151

Western Region: Alaska, Hawaii, Arizona, California, Colorado, ldaho, Montana, Nevada, New Mexico, Oregon, Texas, Utah, Washing- ton, Wyoming.

Western Region 10550 Talbert Avenue P.O.Box 20850
Fountain Valley, California 92728-0850
(800) 633-5151

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS 16

BINDING ARBITRATION

I140A01A-AAT

BINDING ARBITRATION Any claim or dispute you may have related to your vehicle's warranty or the duties contemplated under the war- ranty, including claims related to the refund or partial refund of your vehicle's purchase price (excluding personal in- jury or product liability claims), shall be resolved by binding arbitration. Bind- ing arbitration shall be administered by and through the National Arbitration Forum (NAF) or the American Arbitra- tion Association (AAA), under the Code of Procedure of the entity you select. You will not be responsible for paying filing and hearing fees above $275.00. All other arbitration costs shall be borne by Hyundai Motor America. You are not responsible to pay any of the costs Hyundai incurs. This Binding Arbitration Agreement shall not deprive you of any remedies available to you under applicable law.

The parties are waiving their right to seek remedies in court, including the right to a jury trial. This Binding Arbitration Agreement shall be governed by and interpreted under the Federal Arbitration Act, 9
U.S.C. sections 1-16. Judgment upon any award may be entered in any court having jurisdiction. You may revoke this Arbitration Agree- ment by (1) written notice or (2) elec- tronic notice. Written notice must be delivered (via certified mail) to Hyundai Motor America, Attn: Consumer Af- fairs, 10550 Talbert Avenue, P.O. Box 20849, Fountain Valley, CA 92728- 0849. Electronic notice must be submitted at the following website address : http:// warranty-arbitration.hyundaiUSA.com. Notice must be received within 90
days after you purchase your vehicle.

VEHICLE SPECIFICATIONS

Measurement ................................................................ 9-2
Engine ........................................................................... 9-3
Lubrication Chart ........................................................... 9-4

9 VEHICLE SPECIFICATIONS

J010A01A-AAT MEASUREMENT

Item

Overall length

Overall width

Overall height (unladen)

Wheel base

Wheel tread

Front

Rear

J020A01A-AAT POWER STEERING

Type

Wheel free play

Rack stroke

Oil pump type

J060A01A-AAT FUEL SYSTEM

Fuel tank

capacity

in. (mm)