2006 Honda S2000 Owners Manual

65

Main MenuTable of Contentsst０５／０８／２９　１８：００：２４　３１Ｓ２Ａ６６０　００６９　

Remote Transmitter

Replacing the Transmitter Battery

BATTERY

ROUND COVER

If it takes several pushes on the button to lock or unlock the doors, replace the battery as soon as possible. Battery type: CR2025

66

To replace the battery, remove the round cover on the back of the transmitter by turning it counterclockwise with a coin. Insert a new battery with the side facing mark on the cover up. Align the with the ◎ transmitter. Set the cover in place, and turn it clockwise.

▽ mark on the

＋

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

Main MenuTable of Contentsst０５／０８／２９　１８：００：３０　３１Ｓ２Ａ６６０　００７０　

Seats

−

10 12

for important safety See pages informationandwarningsabouthowto properlypositiontheseatsandseat- backs.

Make all seat adjustments before you start driving.

To adjust the seat forward and backward, pull up on the lever under the seat cushion’s front edge. Then trytomovetheseattomakesureit is locked in position.

To change the seat-back angle, pull up on the lever on the outside of the seat bottom.

67

Main MenuTable of Contentsst０５／０８／２９　１８：００：３５　３１Ｓ２Ａ６６０　００７１　

Power Windows

Turn the ignition switch to the ON (II) position to raise or lower either window. To open the window, push the switch down and hold it. Release the switch when you want the window to stop. Pull back on the switch and hold it to close the window.

DRIVER’S WINDOW SWITCH

Closing a power window on someone’s hands or fingers can cause serious injury.

MAIN SWITCH

Make sure your passenger is away from the window before closing it.

PASSENGER’S WINDOW SWITCH The driver’s armrest has a master power window control panel. To open the passenger’s window, push down on the switch and hold it until the window reaches the desired position. To close the window, pull back on the window switch. Release the switch when the window gets to the position you want.

68

Main MenuTable of Contentsst０５／０８／２９　１８：００：４０　３１Ｓ２Ａ６６０　００７２　

Power Windows

If the MAIN switch is OFF, the passenger’s window cannot be raised or lowered. Keep the MAIN switch off when you have a child in the vehicle so the child does not get injured by operating the window unintentionally.

The master control panel also con- tains these extra features:

−

AUTO To open the driver’s window fully, push the window switch firmly down to the second detent, and release it. The window automatically goes all the way down. To stop the window, pull back on the window switch briefly.

To open the driver’s window only partially, push the window switch down lightly and hold it. The window will stop as soon as you release the switch.

The AUTO function only works to lower the driver’s window. To raise the window, you must pull back on the window switch and hold it until the window reaches the desired position.

69

Main MenuTable of Contentsst０５／０８／２９　１８：００：５０　３１Ｓ２Ａ６６０　００７３　

Lowering the Convertible Top Before operating the convertible top, make sure the vehicle is parked on level ground, the rear defogger is off, and there is enough clearance above the top.

1.

Apply the parking brake. The convertible top will not operate unless the parking brake is fully engaged.

2.

Turn the ignition switch to the ON (II) position.

LATCH

TAB

LOCKING LEVER

3.

There is a latch on each side. Push in the tabs, and pull the locking levers down.

Convertible Top

The convertible top on your vehicle lowers and raises electrically.

It is advisable to raise the top whenever you park the vehicle. This helps to protect the vehicle from unexpected weather changes, and from theft of your valuables.

Do not operate the convertible top in f reezing weather. You can damage the material and the mechanism. Do not operate the top if it is wet, dirty, or covered with ice or snow. Never drive the vehicle with the convertible top half open. Do not operate the convertible top if the vehicle is on a jack, a hoist, or on jack stands. Park your vehicle in the shade whenever possible. Extended exposure to sunlight can cause the convertible top to deteriorate.

70

Main MenuTable of Contentsst０５／０８／２９　１８：００：５５　３１Ｓ２Ａ６６０　００７４　

Convertible Top

Operating the convertible top while any part of a passenger is in the way of the convertible top can cause serious injury.

Make sure that you, your passenger, or any other people around the vehicle are clear of the moving convertible top.

71

LOCKING LEVER

4.

With the latches released, push the locking levers up until they latch.

5.

ROOF SWITCH Pull back and hold the ROOF switch. The windows lower and the roof folds back. Release the ROOF switch when the roof is retracted completely into the rear shelf.

Do not sit on the f olded convertible top, or place any items on top of it. You could damage the top or the rear window.

Main MenuTable of Contentsst０５／０８／２９　１８：０１：０２　３１Ｓ２Ａ６６０　００７５　

Convertible Top

Convertible Top Cover Use the convertible top cover when the top is folded to help prevent foreign objects, dirt, etc., from getting into the material and the mechanism.

The cover is attached to the body with four snaps: two behind the roll bars, and one on the side of each seat. To install or remove the convertible top cover correctly this:

, do

SNAPS

1.

Remove the convertible top cover from the trunk, and lay it into position behind the roll bar.

72

PIN

SNAP

2.

Hold the cover in place with its snap on the driver’s side of the roll bar aligned with the pin on the roll bar. Press on both sides of the snap to attach it to the pin. Do not push or pull the snap button when installing the snap.

3.

Align the snap on the passenger’s side of the roll bar with the pin. Press on both sides of the snap to attach it to the pin.

Main MenuTable of Contentsst０５／０８／２９　１８：０１：１１　３１Ｓ２Ａ６６０　００７６　

FASTENER STRAP

PIN

SNAP

4.

5.

Pull down the strap on the passenger’s side of the cover, and align its snap with the pin on the trim panel behind the door. Press on both sides of the snap to attach it to the pin.

Pull down the strap on the driver’s side of the cover, and align its snap with the pin on the trim panel behind the door. Press on both sides of the snap to attach it to the pin.

6.

Fit the rear of the cover into the space between the convertible top and its molding.

7.

To remove the cover, reverse the procedure.

Convertible Top

Raising the Convertible Top

1.

Apply the parking brake. The convertible top will not operate unless the parking brake is fully engaged.

2.

Turn the ignition switch to the ON (II) position.

3.

Push the ROOF switch forward and hold it. The windows, if raised, will lower automatically.

The convertible top will rise. Release the ROOF switch when the top reaches the windshield header.

73

Main MenuTable of Contentsst０５／０８／２９　１８：０１：２０　３１Ｓ２Ａ６６０　００７７　

Convertible Top

TAB

LATCH

LOCKING LEVER

6.

Push the locking levers up while holding the tab. When the latch is in place, release the tab. Make sure the convertible top is securely latched.

Operating the convertible top while any part of a passenger is in the way of the convertible top can cause serious injury.

4.

5.

Push in the tab to release the locking levers, and pull them down. Note the movement of the latch when you push in the tab.

Make sure that you, your passenger, or any other people around the vehicle are clear of the moving convertible top.

While holding the lever down, push in the tab to engage the latch in the windshield header. Pull the top down and forward if necessary.

Do not put any heavy items on the f olded convertible top. You could damage the material and the mechanism.

74

Maintenance Dust is the main cause of creaks or other sounds coming from the convertible top.

Regularly clean the body seals with glass cleaner and a soft cloth. Do not use a scraper or de-icing chemicals to remove frost, snow, or ice from the top or the rear window.

Every 3 to 6 months, depending on how often the top is folded, rub a thin film of Shin-Etsu Silicon Grease (available from your dealer, P/N 08798-9013) onto the seals wherever they touch the convertible top or each other.

Main MenuTable of Contentsst０５／０８／２９　１８：０１：２９　３１Ｓ２Ａ６６０　００７８　

To reduce the possibility of leaks: Mirrors

Do not lean or sit on an open door.

Do not push or pull the door glass to open and close the door.

TAB

Convertible Top, Mirrors

Adjusting the Power Mirrors

SELECTOR SWITCH

The convertible top seals are designed to promote the flow of water off the roof. Spraying high- pressure water directly on the seals can distort them, causing a leak. Use only a low-pressure water stream when using a hose, and avoid commercial car washes.

Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving.

The inside mirror has day and night positions. The night position reduces glare from headlights behind you. Flip the tab on the bottom edge of the mirror to select the day or night position.

ADJUSTMENT SWITCH

1.

2.

3.

Turn the ignition switch to the ON (II) position. Move the selector switch to L (driver’s side) or R (passenger’s side). Push the appropriate edge of the adjustment switch to move the mirror right, left, up, or down.

75

Main MenuTable of Contentsst０５／０８／２９　１８：０１：３５　３１Ｓ２Ａ６６０　００７９　

Mirrors, Parking Brake

4.

When you finish, move the selector switch to the center (off) position. This turns the adjustment switch off to keep your settings.

Parking Brake

To apply the parking brake, pull the lever up fully. To release it, pull up slightly, push the button, and lower the lever. The parking brake indicator on the instrument panel should go out when the parking brake is fully released (see page

46

).

76

If you try to drive the vehicle without releasing the parking brake, the ABS indicator may come on, and the ABS may not work properly.

Driving the vehicle with the parking brake applied can damage the rear brakes and axles.

If you drive at certain speeds without fully releasing the parking brake, a beeper sounds continuously.

Main MenuTable of Contentsst０５／０８／２９　１８：０１：３９　３１Ｓ２Ａ６６０　００８０　

Interior Convenience Items

CONSOLE COMPARTMENT

ACCESSORY POWER SOCKET

AUDIO PANEL

BEVERAGE HOLDER

DASHBOARD LOWER POCKET

77

Main MenuTable of Contentsst０５／０８／２９　１８：０１：４７　３１Ｓ２Ａ６６０　００８１　

Interior Convenience Items

Beverage Holder

Accessory Power Socket

Console Compartments

This socket is intended to supply power for 12 volt DC accessories that are rated 120 watts or less (10
amps).

They will not power an automotive type cigarette lighter element.

The area between the seats has two compartments. Open the lower compartment by squeezing the handle. Close it with a firm push. You can lock or unlock the lower compartment with the master key.

Open the beverage holder by pushing on the tab. The lid will slide open.

Be careful when you are using the beverage holder. A spilled liquid that is very hot can scald you or your passenger. Spilled liquids can also damage the upholstery, carpeting, and electrical components in the interior.

78

Main MenuTable of Contentsst０５／０８／２９　１８：０１：５４　３１Ｓ２Ａ６６０　００８２　

Interior Convenience Items

Audio Panel

Dashboard Lower Pocket

The lever to open the upper compartment is inside the lower compartment. Push up the lever, and lift the lid. To close, lower the lid, and push it down until it latches.

To open the audio panel, push on the top center, and let the panel swing down. To close, pivot the panel up, and push on it until it latches.

The dashboard lower pocket is located next to the audio panel.

79

Main MenuTable of Contentsst０５／０８／２９　１８：０２：００　３１Ｓ２Ａ６６０　００８３　

Interior Light

DOOR ACTIVATED

If the switch is in the center position, the interior light will come on when you remove the key from the ignition switch.

The interior light has a three- position switch; ON, Door Activated, and OFF. In the Door Activated (center) position, the light comes on when you:

Open either door. Unlock the doors with the key or the remote transmitter.

80

When the switch is in the center position with both doors closed, the two bulbs in the interior light can each be turned on and off with the button next to it.

Main MenuTable of Contentsst０５／０８／２９　１８：０２：０４　３１Ｓ２Ａ６６０　００８４　

Features

The heating and air conditioning system in your vehicle provides a comfortable driving environment in all weather conditions.

The standard audio system has many features. This section describes those features and how to use them. (If you have an optional audio system, refer to the operating instructions that came with it.)

. 82
Vents, Heating, and A/C . 86
Playing the AM/FM Radio AM/FM Radio Reception . 89
Playing the XM Satellite Radio . 91
. 96
Playing a CD CD Changer . 98
. 98
Protecting Your CDs . 99
CD Player Error Messages . 100
CD Changer Error Messages . 101
Remote Audio Controls Radio Theft Protection . 102
. 103
Cruise Control

............... ............ .............. ... .................................... ..................................... ...................... ........... ..... ................ ................. ...............................

81

Main Menust０５／０８／２９　１８：０２：０８　３１Ｓ２Ａ６６０　００８５　

Vents, Heating, and A/C

RECIRCULATION BUTTON

REAR WINDOW DEFOGGER BUTTON

AIR CONDITIONING BUTTON

FAN CONTROL LEVER

82

MODE CONTROL DIAL

TEMPERATURE CONTROL DIAL

Main MenuTable of Contentsst０５／０８／２９　１８：０２：２１　３１Ｓ２Ａ６６０　００８６　

Controlling the Airflow

Fan Control Lever Push this lever up and down to increase or decrease the fan speed and airflow. The indicators next to the lever show you the speed and airflow selected.

Temperature Control Dial Turning this dial clockwise increases the temperature of the airflow.

Air Conditioning (A/C) Button This button turns the air conditioning on and off. The indicator in the button comes on when the A/C is on.

Recirculation Button When the recirculation indicator is on, air from the vehicle’s interior is sent through the system again (recirculation mode). When the indicator is off, air is brought in from the outside of the vehicle (fresh air mode).

The outside air intakes for the heating and cooling system are at the base of the windshield. Keep this area clear of leaves and other debris.

The system should be left in fresh air mode under almost all conditions. Keeping the system in recirculation mode, particularly with the A/C off, can cause the windows to fog up.

Switch to recirculation mode when driving through dusty or smoky conditions, then return to fresh air mode.

Vents, Heating, and A/C

Rear Window Defogger Button This button turns the rear window defogger off and on (see page ). 59

Do not push the defogger button when the convertible top is folded.

Mode Control Dial Use the mode control dial to select the vents the air flows from. Some air will flow from the dashboard vents in all modes.

Air flows from the vents on both sides of the instrument panel, and from the dashboard vent in front of the passenger.

Airflow is divided between the vents in the dashboard and the floor vents.

CONTINUED

83

Main MenuTable of Contentsst０５／０８／２９　１８：０２：３５　３１Ｓ２Ａ６６０　００８７　

Vents, Heating, and A/C

Air flows from the center vents in the dashboard above the audio system, the vents on both sides of the instrument panel, and from the floor vents. Select this position when you drive with the convertible top folded.

Air flows from the floor

vents and the vents on both sides of the instrument panel.

Airflow is divided between

the floor vents and the defroster vents at the base of the windshield, and the vents on both sides of the instrument panel.

Air flows from the defroster

vents at the base of the windshield and the vents on both sides of the instrument panel.

When you select the system automatically switches to fresh air mode and turns on the A/C.

or

84

Ventilation The flow-through ventilation system draws in outside air, circulates it through the interior, then exhausts it through vents behind the seat-backs.

1.

2. 3. 4.

Set the temperature to the lower limit. Make sure the A/C is off. Select Set the fan to the desired speed.

and fresh air mode.

Using the Heater The heater uses engine coolant to warm the air. If the engine is cold, it will be several minutes before you feel warm air coming from the system.

1. 2. 3.

and fresh air mode.

Select Set the fan to the desired speed. Adjust the warmth of the air with the temperature control dial.

Using the A/C Air conditioning places an extra load on the engine. Watch the engine coolant temperature gauge (see page 52
turn off the A/C until the gauge reading returns to normal.

). If it moves near the red zone,

1.

2.

3. 4.

5.

Turn on the A/C by pressing the button. The indicator in the button comes on when a fan speed is selected. Make sure the temperature is set to maximum cool. Select If the outside air is humid, select recirculation mode. If the outside air is dry, select fresh air mode. Set the fan to the desired speed.

you can

Iftheinteriorisverywarm, cool it down more rapidly by partially opening the windows, turning on the A/C, and setting the fan to maximum speed in fresh air mode.

Main MenuTable of Contentsst０５／０８／２９　１８：０２：４６　３１Ｓ２Ａ６６０　００８８　

To Dehumidify the Interior Air conditioning, as it cools, removes moisture from the air. When used in combination with the heater, it makes the interior warm and dry.

4.

5.

to help clear the

airflow feels warm. Select rear window. To increase airflow to the windshield, close the corner vents.

1. 2. 3. 4.

Turn the fan on. Turn on the air conditioning. Select Adjust the temperature to your preference.

and fresh air mode.

This setting is suitable for all driving conditions whenever the outside temperature is above 32°F (0°C).

To Defog and Defrost To remove fog from the inside of the windows:

When you switch to another mode from Press the A/C button to turn it off.

, the A/C stays on.

To Remove Exterior Frost or Ice From the Windows

1.

2. 3.

. The system

Select automatically switches to fresh air mode and turns on the A/C. Select Set the fan and temperature controls to the maximum level.

1.

2.

3.

Set the fan to the desired speed. Select high for faster defrosting. Select automatically switches to fresh air mode and turns on the A/C. Adjust the temperature so the

. The system

To clear the windows faster, you can close the dashboard corner vents and the vents on both sides of the instrument panel by rotating the wheel below the vent. This will send more warm air to the windshield

Vents, Heating, and A/C

defroster vents. Once the windshield is clear, select fresh air mode to avoid fogging the windows.

For your safety, make sure you have a clear view through all the windows before driving.

To Turn Everything Off Push the fan control level down until the indicator goes off. A lack of airflow can cause the windows to fog up. You should keep the fan on at all times so stale air and moisture do not build up in the interior and cause fogging.

85

Main MenuTable of Contentsst０５／０８／２９　１８：０２：５１　３１Ｓ２Ａ６６０　００８９　

Playing the AM/FM Radio

AUTO SELECT INDICATOR STEREO INDICATOR

AM/FM BUTTON

SCAN INDICATOR

SCAN BUTTON

AUTO SELECT BUTTON

SEEK BAR

TUNE KNOB

POWER/VOLUME KNOB

PRESET BUTTONS

86

Main MenuTable of Contentsst０５／０８／２９　１８：０３：０１　３１Ｓ２Ａ６６０　００９０　

Playing the AM/FM Radio

To Play the Radio The ignition switch must be in the ACCESSORY (I) or the ON (II) position. Turn the system on by pushing the PWR/VOL knob or the FM/AM button. Adjust the volume by turning the PWR/VOL knob.

The band and frequency that the radio was last tuned to is displayed. To change bands, press the FM/AM button. On the FM band, ST will be displayed if the station is broadcast- ing in stereo. Stereo reproduction on AM is not available.

To Select a Station You can use any of five methods to find radio stations on the selected band: the preset buttons, and

TUNE, SEEK, SCAN,

AUTO SELECT

−

Use the TUNE knob to

TUNE tune the radio to a desired frequency. Turn the knob right to tune to a higher frequency, or left to tune to a

lower frequency.

−

The seek function

SEEK searches up and down from the current frequency to find a station with a strong signal. To activate it, press the side of the bar, then release it.

or

−

SCAN The scan function samples all stations with strong signals on the selected band. To activate it, press the SCAN button, then release it. You will see SCAN in the display. The system will scan for a station with a strong signal. When it finds one, it will stop and play that station for about 5 seconds.

If you do nothing, the system will scan for the next strong station and play it for 5 seconds. When it plays a station you want to listen to, press the SCAN button again.

−

Each preset button can

Preset store one frequency on AM and two frequencies on FM.

1.

Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each preset button.

2.

Use the tune, seek, or scan function to tune the radio to a desired station.

3.

Pick a preset button, and hold it until you hear a beep.

4.

Repeat steps 1 through 3 to store a total of six stations on AM and twelve stations on FM.

The preset frequencies will be lost if your vehicle’s battery goes dead, is disconnected, or the radio fuse is removed.

CONTINUED

87

Main MenuTable of Contentsst０５／０８／２９　１８：０３：１１　３１Ｓ２Ａ６６０　００９１　

Playing the AM/FM Radio

Turn the knob to adjust the setting. When the level reaches the center, you will see a ‘‘C’’ in the display. The system will return to the audio display in about 5 seconds.

Audio System Lighting You can use the instrument panel brightness control buttons to adjust the illumination of the audio system (see page illuminates when the parking lights are on, even if the radio is off.

). The audio system

58

Toturnoffautoselect A. SEL button. This restores the presets you originally set.

,pressthe

Adjusting the Sound BAL to-side strength of the sound.

Adjusts the balance, or side-

−

−

FAD front-to-back strength of the sound.

Adjusts the fader, or the

TRE − sound.

BAS − sound.

Adjusts the treble in the

Adjusts the bass in the

Press the SOUND (TUNE) knob repeatedly to display the bass (BAS), treble (TRE), balance (BAL), and fader (FAD) setting.

−

If you are

AUTO SELECT traveling far from home and can no longer receive your preset stations, you can use the auto select feature to find stations in the local area.

Press the A. SEL button. ‘‘A.SEL’’ flashes in the display, and the system goes into scan mode for several seconds. It stores the frequencies of six AM and twelve FM stations in the preset buttons.

You will see a ‘‘0’’ displayed after pressing a preset button if auto select cannot find a strong station for every preset button.

If you do not like the stations auto select has stored, you can store other frequencies on the preset buttons as previously described.

88

Main MenuTable of Contentsst０５／０８／２９　１８：０３：２０　３１Ｓ２Ａ６６０　００９２　

Radio Frequencies The radio can receive the complete AM and FM bands. Those bands cover these frequen- cies:

AM band: 530 to 1,710 kilohertz FM band: 87.7 to 107.9 megahertz

Radio stations on the AM band are assigned frequencies at least 10
kilohertz apart (530, 540, 550). Stations on the FM band are assigned frequencies at least 0.2
megahertz apart (87.9, 88.1, 88.3).

Stations must use these exact frequencies. It is fairly common for stations to round-off the frequency in their advertising, so your radio could display a frequency of 100.9 even though the announcer may identify the station as ‘‘FM101.’’

Radio Reception How well the radio receives stations is dependent on many factors, such as the distance from the station’s transmitter, nearby large objects, and atmospheric conditions.

A radio station’s signal gets weaker as you get farther away from its transmitter. If you are listening to an AM station, you will notice the sound volume becoming weaker, and the station drifting in and out. If you are listening to an FM station, you will see the stereo indicator flickering off and on as the signal weakens. Eventually, the stereo indicator will go off and the sound will fade completely as you get out of range of the station’s signal.

AM/FM Radio Reception

Driving very near the transmitter of a station that is broadcasting on a frequency close to the frequency of the station you are listening to can also affect your radio’s reception. You may temporarily hear both stations, or hear only the station you are close to.

CONTINUED

89

Main MenuTable of Contentsst０５／０８／２９　１８：０３：２６　３１Ｓ２Ａ６６０　００９３　

AM/FM Radio Reception

AsrequiredbytheFCC: Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills. Your radio then receives both the direct signal from the station’s transmitter, and the deflected signal. This causes the sound to distort or flutter. This is a main cause of poor radio reception in city driving.

Radio reception can be affected by atmospheric conditions such as thunderstorms, high humidity, and even sunspots. You may be able to receive a distant radio station one day and not receive it the next day because of a change in conditions.

Electrical interference from passing vehicles and stationary sources can cause temporary reception problems.

90

Main MenuTable of Contentsst０５／０８／２９　１８：０３：３２　３１Ｓ２Ａ６６０　００９４　

OptionalonU.S.models NotavailableonCanadianmodels Your vehicle is capable of receiving XM Satellite Radio anywhere in the United States, except Hawaii and Alaska.

XM is a registered trademark of XM Satellite Radio, Inc.

Satellite radio receives signals from two satellites to produce clear, high- quality digital reception. It offers many channels in several categories. Along with a large selection of different types of music, satellite radio also allows you to view channel and category selections in the audio display.

Playing the XM Satellite Radio (Optional on U.S. Models)

AM/FM BUTTON

TUNE KNOB

CD/XM BUTTON

SCAN BUTTON

POWER/VOLUME KNOB

PRESET BUTTONS

MORE BUTTON

CATEGORY BAR

DISPLAY/MODE BUTTON

91

Main MenuTable of Contentsst０５／０８／２９　１８：０３：３９　３１Ｓ２Ａ６６０　００９５　

Playing the XM Satellite Radio (Optional on U.S. Models)

Playing the Satellite Radio To listen to satellite radio, turn the ignition switch to the ACCESSORY (I) or the ON (II) position. Push the PWR/VOL knob to turn on the audio system, and press the CD/XM button. Adjust the volume by turning the PWR/VOL knob. The last channel you listened to will show in the display.

−

DISPLAY/MODE Each time the DISP button is pressed and released, the display information changes in the following sequence: channel name, channel number, category, artist name, and music title.

You may experience periods when XM radio does not transmit the artist name and or the song title information. If this happens, there is nothing wrong with your system. This information is not available under certain situations.

If you press and hold the DISP/ MODE button for 5 seconds, it will change between category mode and channel mode. The display will show CH for the channel mode or CATEGORY for the category mode.

In the channel mode, you can receive all of the available channels in all of the different categories. In category mode, you will receive only the stations within the selected category.

−

Expands the display to

MORE show the 6 remaining letters beyond the first 10 letters in an artist’s name or song title. The system is set up so only 16 letters can be displayed for

92

any title or name. Press MORE to view the next 6 letters. The system will return to the original display after 8 seconds.

−

TUNE Turn the TUNE knob left to go down the channels or right to go up. In the channel mode, the TUNE knob will tune up or down through all the channels available from the XM radio. In the category mode, the TUNE knob will cycle through only the channels within the category you have currently selected.

Use

CATEGORY (SEEK/SKIP) − the CATEGORY bar to select a desired category, such as jazz, rock, classical, etc. In both category mode and channel mode, pressing the category bar will change the category up or down.

Main MenuTable of Contentsst０５／０８／２９　１８：０３：４９　３１Ｓ２Ａ６６０　００９６　

Playing the XM Satellite Radio (Optional on U.S. Models)

−

The scan function gives

SCAN you a sampling of all channels while in the channel mode. In the category mode, only the channels within that category are scanned. To activate scan, press the SCAN button. The system plays each channel in numerical order for a few seconds, then selects the next channel. When you hear a channel you want to continue listening to, press the button again.

−

You can store up to 12

To store a channel: Preset preset channels using the six preset buttons. Each button stores one channel from the XM1 band and one channel from the XM2 band.

3.

Pick the preset button you want for that channel. Press and hold the button until you hear a beep.

4.

Repeat steps 2 through 3 to store the first six channels.

To store a channel: 1.

Press the CD/XM button. Either XM1 or XM2 will show in the display.

5.

Press the CD/XM button again. The available XM band will show. Store the next six channels using steps 2 through 3.

2.

Use the TUNE knob, the CATEGORY bar, or the SCAN buttons to tune to a desired channel.

In category mode, only channels within that category can be selected. In channel mode, all channels can be selected.

Once a channel is stored, simply press and release the proper preset button to tune to it.

The presets will be lost if your vehicle’s battery goes dead, is disconnected, or the radio fuse is removed.

CONTINUED

93

Main MenuTable of Contentsst０５／０８／２９　１８：０３：５３　３１Ｓ２Ａ６６０　００９７　

Playing the XM Satellite Radio (Optional on U.S. Models)

Signal may be blocked by mountains or large obstacles to the south.

Signal is weaker in these areas.

The XM satellites are in orbit over the equator; therefore, objects south of the vehicle may cause satellite reception interruptions. To help compensate for this, ground-based repeaters are placed in major metropolitan areas.

Satellite signals are more likely to be blocked by tall buildings and mountains the farther north you travel from the equator.

SATELLITE

94

GROUND REPEATER

Main MenuTable of Contentsst０５／０８／２９　１８：０４：０３　３１Ｓ２Ａ６６０　００９８　

Playing the XM Satellite Radio (Optional on U.S. Models)

Depending on where you drive, you may experience reception problems. Interference can be caused by any of these conditions:

Driving on the south side of an east/west mountain road.

Driving on the north side of a large commercial truck on an east/west road.

Driving in tunnels.

Driving on a road beside a vertical wall, steep cliff, or hill to the south of you.

Driving on the lower level of a multi-tiered road.

Driving on a single lane road alongside dense trees taller than 50 ft. (15 m) to the south of you.

There may also be other geographic situations that could affect satellite radio reception.

AsrequiredbytheFCC: Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

Receiving Satellite Radio Service If your XM Radio service has expired, or you purchased your vehicle from a previous owner, you can listen to a sampling of the broadcasts available on XM Satellite Radio. With the ignition switch in the ACCESSORY (I) or the ON (II) position, push the PWR/VOL knob to turn on the audio system, and press the CD/XM button. A variety of music types and styles will play.

If you decide to purchase XM satellite radio service, contact XM Radio at

www.xmradio.com

, or at

1-800-852-9696. You will need to give them your radio I.D. number and your credit card number. To get your radio I.D. number, turn the TUNE knob until ‘‘0’’ appears in the display. Your I.D. will appear in the display.

After you’ve registered with XM Radio, keep your audio system in the Satellite Radio mode while you wait for activation. This should take about 30 minutes.

While waiting for activation, make sure your vehicle remains in an open area with good reception. Once your audio system is activated, ‘‘category’’ or ‘‘CH’’ will appear in the display, and you’ll be able to listen to XM Radio broadcasts. XM Radio will continue to send an activation signal to your vehicle for at least 12 hours from the activation request. If the service has not been activated after 36 hours, contact XM Radio.

95

Main MenuTable of Contentsst０５／０８／２９　１８：０４：０８　３１Ｓ２Ａ６６０　００９９　

Playing a CD

AM/FM BUTTON

CD SLOT

EJECT BUTTON

CD BUTTON

REPEAT INDICATOR

REPEAT BUTTON

RANDOM BUTTON

SEEK/SKIP BAR

POWER/VOLUME KNOB

RANDOM INDICATOR

96

Main MenuTable of Contentsst０５／０８／２９　１８：０４：１６　３１Ｓ２Ａ６６０　０１００　

To Play a CD With the ignition switch in the ACCESSORY (I) or the ON (II) position, insert a CD into the CD slot. The drive will pull the CD in the rest of the way and begin to play it. The number of the track playing is shown in the display. The system will continuously play a CD until you change modes.

Do not use discs with adhesive labels. The label can curl up and cause the disc to jam in the unit.

−

side of the skip bar,

Each time you press and

SKIP release the the player skips forward to the beginning of the next track. Press and release the side of the bar to skip backward to the beginning of the current track. Press it again to skip to the beginning of the previous track.

To move rapidly within a track, press and hold the side. You will see CUE or REW in the display.

or

−

To continuously replay

REPEAT a track, press and release the RPT button. You will see RPT in the display. Press it again to turn it off.

−

RANDOM This feature plays the tracks in random order. To activate random play, press and release the RDM button. You will see RDM in the display. Press it again to return to normal play.

Playing a CD

) to

To Stop Playing a CD Press the eject button ( remove the CD. If you eject the CD, but do not remove it from the slot, the system will automatically reload the CD after 15 seconds and put it in pause mode. To begin playing, press the CD button. Press the AM/FM button to switch to the radio while a CD is playing.

If you turn the system off while a CD is playing, either with the PWR/VOL knob or by turning off the ignition switch, the CD will stay in the drive. When you turn the system back on, the CD will begin playing where it left off.

97

Main MenuTable of Contentsst０５／０８／２９　１８：０４：２７　３１Ｓ２Ａ６６０　０１０１　

CD Changer, Protecting Your CDs

Operating the Optional CD Changer An optional six disc CD changer is available for your vehicle. This CD changer uses the same controls used for the in-dash CD player.

Load the desired CDs into the magazine, and load the magazine into the changer according to the instructions that came with the unit.

To select the CD changer, press the CD button. The CD and track numbers will be displayed. To select a different CD, use the preset 5
(DISC ) or preset 6 (DISC ) ＋ button. If you select an empty slot in the magazine, the changer will, after finding that slot empty, try to load the CD in the next slot.

−

Protecting Your CDs GeneralInformation

When using CD-R discs, use only high quality CDs labeled for audio use.

When recording a CD-R, the recording must be closed for it to be used by the system.

CD-RW discs will not work in this unit.

Play only standard round CDs. Odd-shaped CDs may jam in the drive or cause other problems.

Handle your CDs properly to prevent damage and skipping.

ProtectingCDs When a CD is not being played, store it in its case to protect it from dust and other contamination. To prevent warpage, keep CDs out of direct sunlight and extreme heat.

To clean a CD, use a clean soft cloth. Wipe across the CD from the center to the outside edge.

A new CD may be rough on the inner and outer edges. The small plastic pieces causing this roughness can flake off and fall on the re- cording surface of the CD, causing skipping or other problems. Remove these pieces by rubbing the inner and outer edges with the side of a pencil or pen.

Never try to insert foreign objects in the CD player or the magazine.

98

Main MenuTable of Contentsst０５／０８／２９　１８：０４：３４　３１Ｓ２Ａ６６０　０１０２　

Protecting Your CDs, CD Player Error Messages

CD Player Error Messages If you see an error message in the display while playing a CD, find the cause in the chart below. If you cannot clear the error message, take the vehicle to your dealer.

Error Message

Cause

Solution

FOCUS Error

Mechanical Error

High temperature

Press the EJECT button, and pull out the CD. Check if the CD is inserted correctly in the CD player. Make sure the CD is not scratched or damaged. Press the EJECT button, and pull out the CD. Check the CD for damage or deformation. If the CD cannot be pulled out or the error message does not disappear after the CD is ejected, see your dealer. Do not try to force the disc out of the player. Will disappear when the temperature returns to normal.

99

Handle a CD by its edges; never touch either surface. Do not place stabilizer rings or labels on the CD. These, along with contamination from fingerprints, liquids, and felt-tip pens, can cause the CD to not play properly or possibly jam in the drive.

Main MenuTable of Contentsst０５／０８／２９　１８：０４：４１　３１Ｓ２Ａ６６０　０１０３　

CD Changer Error Messages

If you see an error message in the display while playing a CD, find the cause in the chart to the right. If you cannot clear the error message, take the vehicle to your dealer.

Error Message

100

Cause

Solution

FOCUS Error

No CD in the CD magazine

Mechanical Error

High temperature

No CD magazine in the CD changer

Press the magazine eject button, pull out the magazine, and check for an error message. Insert the magazine again. If the error message does not disappear or the magazine cannot be pulled out, see your dealer. Insert CD.

Press the magazine eject button, and pull it out. Check for an error message, and insert the magazine again. If the error message does not disappear or the magazine cannot be pulled out, see your dealer. Will disappear when the temperature returns to normal. Insert CD magazine.

Main MenuTable of Contentsst０５／０８／２９　１８：０４：４９　３１Ｓ２Ａ６６０　０１０４　

AUDIO CONTROL BUTTON

CHANNEL BUTTON

MUTE BUTTON

VOLUME BAR

Four controls for the audio system are on the left side of the dashboard by the instrument panel. These let you control basic functions without distracting your attention from driving.

Use the VOLUME bar to adjust the volume. Push ＋ volume and to decrease it. Hold − the lever until the volume reaches the desired level, then release it.

to increase the

If you want to mute the sound temporarily, push the MUTE button. The indicator in the button will come on to indicate the mute function is on. Press the button again to cancel mute.

The AUDIO CONTROL button changes the mode. Pressing the button repeatedly selects AM, FM1, FM2, or CD (if a CD is loaded), XM1, XM2 (if you have the optional satellite radio feature).

The CHANNEL button has two functions, depending on whether you are listening to the radio, or playing a CD.

If you are listening to the radio, use the CHANNEL button to change stations. Each time you press this button, the system advances to the next preset station on the band you are listening to. You will see the number of the selected preset button

Remote Audio Controls

in the audio system display.

If you are playing a CD, the system skips to the beginning of the next track each time you push the CHANNEL button.

These controls work only with the factory-installed audio system. They will not function if you install any non-Honda system.

101

Main MenuTable of ContentsstYou will have to store your favorite stations in the preset buttons after the system begins working. Your original settings were lost when the power was disconnected.

０５／０８／２９　１８：０４：５４　３１Ｓ２Ａ６６０　０１０５　

Radio Theft Protection

Your vehicle’s audio system will disable itself if it is disconnected from electrical power for any reason. To make it work again, you must enter a specific five-digit code in the preset buttons. Because there are hundreds of number combinations possible from five digits, making the system work without knowing the exact code is nearly impossible.

You should have received a card that lists your audio system’s code and serial numbers. It is best to store this card in a safe place at home. In addition, you should write the audio system’s serial number in this owner’s manual. If you lose the card, you must obtain the code number from a dealer. To do this, you will need the system’s serial number.

If your vehicle’s battery is disconnected or goes dead, or the radio fuse is removed, the audio system will disable itself. If this happens, you will see ‘‘Code’’ in the frequency display the next time you turn on the system. Use the preset buttons to enter the five-digit code. The code is on the radio code card included in your owner’s manual kit. When it is entered correctly, the radio will start playing.

If you make a mistake entering the code, do not start over; complete the five-digit sequence, then enter the correct code. You have 10 tries to enter the correct code. If you are unsuccessful in 10 attempts, you must then leave the system on for 1
hour before trying again.

102

Main MenuTable of Contentsst０５／０８／２９　１８：０５：０３　３１Ｓ２Ａ６６０　０１０６　

Cruise control allows you to maintain a set speed above 25 mph (40 km/h) without keeping your foot on the accelerator pedal. It should be used for cruising on straight, open highways. It is not recommended for city driving, winding roads, slippery roads, heavy rain, or bad weather.

Improper use of the cruise control can lead to a crash.

Use the cruise control only when traveling on open highways in good weather.

The cruise control, as it operates, moves the accelerator pedal. You can damage your vehicle’s accelerator mechanism by resting your f oot under the pedal and blocking the movement.

Cruise Control

Using Cruise Control

CANCEL BUTTON

RESUME/accel

CRUISE BUTTON

1.

Push in the CRUISE button. The indicator over the button comes on.

3.

2.

Accelerate to the desired cruising speed above 25 mph (40 km/h).

SET/decel Press and release the SET/decel button on the steering wheel. The indicator on the instrument panel comes on to show the system is now activated.

CONTINUED

103

Main MenuTable of Contentsst０５／０８／２９　１８：０５：１０　３１Ｓ２Ａ６６０　０１０７　

Cruise Control

Cruise control may not hold the set speed when you are going up and down hills. If your speed increases going down a hill, use the brakes to slow down. This will cancel the cruise control. To resume the set speed, press the RESUME/accel button. The indicator on the instrument panel will come back on.

104

Changing the Set Speed You can increase the set cruising speed in any of these ways:

Press and hold the RESUME/ accel button. When you reach the desired cruising speed, release the button.

Push on the accelerator pedal. Accelerate to the desired cruising speed, and press the SET/decel button.

To increase the speed in very small amounts, tap the RESUME/ accel button. Each time you do this, your vehicle speeds up about 1 mph (1.6 km/h).

You can decrease the set cruising speed in any of these ways:

Press and hold the SET/decel button. Release the button when you reach the desired speed.

To slow down in very small amounts, tap the SET/decel button. Each time you do this, your vehicle will slow down about 1 mph (1.6 km/h).

Tap the brake or clutch pedal lightly with your foot. The CRUISE CONTROL indicator on the instrument panel goes out. When the vehicle slows to the