2005 Honda S2000 Owners Manual

Main MenuTable of Contentsst０４／０７／２１　１２：３２：５３　３１Ｓ２Ａ６５０　０１４７　

Lights

Replacing Rear Bulbs

4.

Determine which bulb is burned out: turn signal or back-up light.

5.

Remove the socket by turning it one-quarter turn counterclockwise.

6.

Remove the burned out bulb by pulling it straight out of its socket.

1.

Open the trunk.

2.

Remove the fasteners from the trunk lining. To remove a fastener, push on the center of the head until it pops in, then pull the fastener out.

3.

Pull the lining back.

144

Main MenuTable of Contentsst０４／０７／２１　１２：３３：０１　３１Ｓ２Ａ６５０　０１４８　

7.

Install the new bulb into the socket.

8.

Push the socket into the light assembly, and turn it clockwise until it locks.

9.

Turn on the lights to make sure the new bulb is working.

Lights, Cleaning the Seat Belts

Cleaning the Seat Belts If your seat belts get dirty, use a soft brush with a mixture of mild soap and warm water to clean them. Do not use bleach, dye, or cleaning solvents. Let the belts air-dry before you use the vehicle.

Dirt build-up in the loops of the seat belt anchors can cause the belts to retract slowly. Wipe the insides of the loops with a clean cloth dampened in mild soap and warm water or isopropyl alcohol.

145

10.

Install the trunk lining, and secure it with the fasteners. To reinstall a fastener, reset the fastener by pushing on the pointed end until it pops back almost flush with the fingers on the housing. Put the fastener in the hole of the trunk lining, and push on the center until it locks (the center is flush with the head).

Main MenuTable of Contentsst０４／０７／２１　１２：３３：１０　３１Ｓ２Ａ６５０　０１４９　

Floor Mats, Dust and Pollen Filter

Floor Mats

If you use a non-Honda floor mat, make sure it fits properly and that it can be used with the floor mat anchor. Do not put additional floor mats on top of the anchored mat.

Dust and Pollen Filter This filter removes the dust and pollen that is brought in from the outside through the heating and cooling system.

Have your dealer replace this filter every 30,000 miles (48,000 km) under normal conditions. It should be replaced every 15,000 miles (24,000 km) if you drive primarily in urban areas that have high concentrations of soot in the air, or if the flow from the heating and cooling system becomes less than usual.

The driver’s floor mat that came with your vehicle hooks over the floor mat anchor. This keeps the floor mat from sliding forward and possibly interfering with the pedals.

If you remove the driver’s floor mat, make sure to re-anchor it when you put it back in your vehicle.

146

Main MenuTable of Contentsst０４／０７／２１　１２：３３：１９　３１Ｓ２Ａ６５０　０１５０　

Check the condition of the wiper blades at least every six months. Replace them if you find signs of cracking in the rubber, areas that are getting hard, or if they leave streaks and unwiped areas when used.

To replace a wiper blade: 1.

Raise the wiper arm off the windshield.

Wiper Blades

LOCK TAB

BLADE

Do not open the hood when the wiper arms are raised, or you will damage the hood and the wiper arms.

2.

Disconnect the blade assembly from the wiper arm by pushing in the lock tab. Hold the lock tab in while you push the blade assembly toward the base of the arm.

3.

Remove the blade from its holder by grasping the tabbed end of the blade. Pull firmly until the tabs come out of the holder.

CONTINUED

147

Main MenuTable of Contentsst０４／０７／２１　１２：３３：２８　３１Ｓ２Ａ６５０　０１５１　

Wiper Blades, Tires

BLADE

5.

Slide the new wiper blade into the holder until the tabs lock.

6.

Slide the wiper blade assembly onto the wiper arm. Make sure it locks in place.

7.

Lower the wiper arm down against the windshield.

Tires To safely operate your vehicle, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated.

The following pages give more detailed information on how to take care of your tires and what to do when they need to be replaced.

REINFORCEMENT

4.

Examine the new wiper blades. If they have no plastic or metal reinforcement along the back edge, remove the metal reinforcement strips from the old wiper blade, and install them in the slots along the edge of the new blade.

148

Using tires that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed.

Follow all instructions in this owner’s manual regarding tire inflation and maintenance.

Main MenuTable of Contentsst０４／０７／２１　１２：３３：３９　３１Ｓ２Ａ６５０　０１５２　

Inflation Guidelines Keeping the tires properly inflated provides the best combination of handling, tread life, and riding comfort.

Underinflated tires wear unevenly, adversely affect handling and fuel economy, and are more likely to fail from being overheated.

Overinflated tires can make your vehicle ride more harshly, are more prone to damage from road hazards, and wear unevenly.

We recommend that you visually check your tires every day. If you think a tire might be low, check it immediately with a tire gauge.

Use a gauge to measure the air pressure in each tire at least once a month. Even tires that are in good condition may lose one to two psi (10
to 20 kPa, 0.1 to 0.2 kgf/cm ) per month. Remember to check the spare tire at the same time.

Check the air pressures when the tires are cold. This means the vehicle has been parked for at least three hours, or driven less than 1
mile (1.6 km). Add or release air, if needed, to match the recommended cold tire pressures on page

150

Tires

If you check air pressures when the tires are hot [driven for several miles (kilometers)], you will see readings 4
to 6 psi (30 to 40 kPa, 0.3 to 0.4
kgf/cm ) higher than the cold readings. This is normal. Do not let air out to match the recommended cold air pressure. The tire will be underinflated.

You should use your own tire pressure gauge whenever you check your tire pressures. This will make it easier for you to tell if a pressure loss is due to a tire problem and not due to a variation between gauges.

While tubeless tires have some ability to self-seal if they are punctured, you should look closely for punctures if a tire starts losing pressure.

149

Main MenuTable of Contentsst０４／０７／２１　１２：３３：５４　３１Ｓ２Ａ６５０　０１５３　

Tires

Recommended Tire Pressures The following chart shows the recommended cold tire pressures for most normal and high-speed driving conditions.

Tire Inspection Every time you check inflation, you should also examine the tires for damage, foreign objects, and wear. You should look for:

TREAD WEAR INDICATORS

Bumps or bulges in the tread or side of the tire. Replace the tire if you find either of these conditions.

Cuts, splits, or cracks in the side of the tire. Replace the tire if you can see fabric or cord.

Excessive tread wear.

Front:

Tire Size

215/45R17 87W

Rear:

Tire Size

245/40R17 91W

Cold Tire Pressure 32 psi (220 kPa , 2.2
kgf/cm )

Cold Tire Pressure 32 psi (220 kPa , 2.2
kgf/cm )

The compact spare tire pressure is: 60 psi (420 kPa , 4.2 kgf/cm )

For convenience, the recommended cold air pressures and tire sizes are on a label on the driver’s doorjamb.

For additional information about your tires, see page

186

150

INDICATOR LOCATION MARKS Your tires have wear indicators molded into the tread. When the tread wears down, you will see a 1/2
inch (12.7 mm) wide band across the tread. This shows there is less than 1/16 inch (1.6 mm) of tread left on the tire.

A tire this worn gives very little traction on wet roads. You should replace the tire if you can see three or more tread wear indicators.

Main MenuTable of Contentsst０４／０７／２１　１２：３４：０６　３１Ｓ２Ａ６５０　０１５４　

Tire Maintenance In addition to proper inflation, correct wheel alignment helps to decrease tire wear. If you find a tire is worn unevenly, have your dealer check the wheel alignment.

Have your dealer check the tires if you feel a consistent vibration while driving. A tire should always be rebalanced if it is removed from the wheel. When you have new tires installed, make sure they are balanced. This increases riding comfort and tire life. For best results, have the installer perform a dynamic balance.

Improper wheel weights can damage your vehicle’s aluminum wheels. Use only Honda wheel weights f or balancing.

Tire Rotation You should not rotate your vehicle’s tires. The front and rear tires are different sizes, so they cannot be rotated front-to-rear. The original- equipment tires on your vehicle have a unidirectional tread pattern, so they cannot be rotated side-to-side.

Tire Wear The tires that came on your vehicle were designed and constructed to provide superior grip during acceleration, braking, and cornering.

As a trade-off, they will wear more rapidly than tires used on ordinary passenger vehicles. Because of the vehicle’s weight distribution, and the fact that the rear wheels are the driving wheels, you can expect them to wear more rapidly than the front tires.

Tires

The mileage you can expect from your vehicle tires is the same as comparable mid-and rear-engine sports cars, and it will vary greatly with your driving habits.

If you drive moderately, the rear tires could last more than 10,000
miles (16,000 km). However, the mileage will be substantially less if you tend to drive your vehicle at the upper limits of its capabilities.

You should carefully inspect your vehicle’s tires for wear, damage, and proper inflation every 7,500 miles (12,000 km) (see page

125

).

151

Main MenuTable of Contentsst０４／０７／２１　１２：３４：２２　３１Ｓ２Ａ６５０　０１５５　

Tires

Replacing Tires and Wheels Replace your tires with radial tires of the same size, load range, speed rating, and maximum cold tire pressure rating (as shown on the tire’s sidewall).

Mixing radial and bias-ply tires on your vehicle can reduce braking ability, traction, and steering accuracy. Using tires of a different size or construction can cause the ABS to work inconsistently.

It is best to replace all four tires at the same time. If that is not possible or necessary, replace the two front tires or two rear tires as a pair. Replacing just one tire can seriously affect your vehicle’s handling.

152

The ABS works by comparing the speed of the wheels. When replacing tires, use the same size originally supplied with the vehicle. Tire size and construction can affect wheel speed and may cause the system to work.

If you ever replace a wheel, make sure that the wheel’s specifications match those of the original wheels. Replacement wheels are available at your dealer.

Installing improper tires on your vehicle can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed.

Always use the size and type of tires recommended in this owner’s manual.

Wheel and Tire Specifications Wheels: Front:

17 x 7 JJ

Rear:

17 x 8 1/2 JJ

Tires:

Front:

Rear:

215/45R17 87W

245/40R17 91W

186

for information about

See page DOT Tire Quality Grading, and page 188
information.

for tire size and labeling

Main MenuTable of Contentsst０４／０７／２１　１２：３４：３１　３１Ｓ２Ａ６５０　０１５６　

Winter Driving Tires marked ‘‘M S’’ or ‘‘All Season’’ on the sidewall have an all- weather tread design suitable for most winter driving conditions.

＋

For the best performance in snowy or icy conditions, you should install snow tires or tire chains. They may be required by local laws under certain conditions.

SnowTires If you mount snow tires on your vehicle, make sure they are radial tires of the same size and load range as original tires. Mount snow tires on all four wheels. The traction provided by snow tires on dry roads may be lower than your original tires. Check with the tire dealer for maximum speed recommendations.

TireChains Because your vehicle has limited tire clearance, mount only SAE Class ‘‘S’’ cable-type traction devices, with rubber chain tensioners on the rear tires. Use traction devices only when required by driving conditions or local laws. Make sure they are the correct size for your tires. Metal link- type ‘‘chains’’ should not be used.

When installing cables, follow the manufacturer’s instructions, and mount them as tight as you can. Make sure they are not contacting the brake lines or suspension. Drive slowly with them installed. If you hear them coming into contact with the body or chassis, stop and investigate. Remove them as soon as you begin driving on cleared roads.

Tires

Traction devices that are the wrong size or improperly installed can damage your vehicle’s brake lines, suspension, body, and wheels. Stop driving if they are hitting any part of the vehicle.

153

Main MenuTable of Contentsst０４／０７／２１　１２：３４：３９　３１Ｓ２Ａ６５０　０１５７　

Checking the Battery

Check the terminals for corrosion (a white or yellowish powder). To remove it, cover the terminals with a solution of baking soda and water. It will bubble up and turn brown. When this stops, wash it off with plain water. Dry off the battery with a cloth or paper towel. Coat the terminals with grease to help prevent future corrosion.

If additional battery maintenance is needed, see your dealer or a qualified technician.

Battery posts,

WARNING: terminals, and related accessories contain lead and lead compounds. Wash your hands after handling.

If you need to connect the battery to a charger, disconnect both cables to prevent damaging your vehicle’s electrical system. Always disconnect the negative ( − reconnect it last.

) cable first, and

The battery gives off explosive hydrogen gas during normal operation.

A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you.

Wear protective clothing and a face shield, or have a skilled mechanic do the battery maintenance.

TEST INDICATOR WINDOW Check the condition of the battery monthly by looking at the test indicator window. The label on the battery explains the test indicator’s colors.

154

Main MenuTable of Contentsst０４／０７／２１　１２：３４：５４　３１Ｓ２Ａ６５０　０１５８　

If you need to park your vehicle for an extended period (more than one month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your vehicle back on the road. If possible, store your vehicle indoors.

Fill the fuel tank.

Block the rear wheels.

If the vehicle is to be stored for a longer period, it should be supported on jackstands so the tires are off the ground.

Leave one window open slightly (if the vehicle is being stored indoors).

Change the engine oil and filter.

Disconnect the battery.

Wash and dry the exterior completely.

Clean the interior. Make sure the carpeting, floor mats, etc., are completely dry.

Raise the convertible top cover.

Leave the parking brake off. Put the transmission in Reverse.

Support the front wiper blade arms with a folded towel or rag so they do not touch the windshield.

To minimize sticking, apply a silicone spray lubricant to all door and trunk seals. Also, apply a vehicle body wax to the painted surfaces that mate with the door and trunk seals.

Vehicle Storage

Cover the vehicle with a ‘‘breathable’’ cover, one made from a porous material such as cotton. Non-porous materials, such as plastic sheeting, trap moisture, which can damage the paint.

If possible, periodically run the engine until it reaches full operating temperature (the cooling fan cycles on and off twice). Preferably, do this once a month.

If you store your vehicle for 1 year or longer, have your dealer perform the inspections called for in the 2 years/ 30,000 miles (48,000 km) maintenance schedule (Normal Conditions) as soon as you take it out of storage (see page ). The replacements called for in the maintenance schedule are not needed unless the vehicle has actually reached that time or mileage.

125

155

Main MenuTable of Contentsst０４／０７／２１　１２：３５：００　３１Ｓ２Ａ６５０　０１６０　

Taking Care of the Unexpected

This section covers the more common problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your vehicle towed.

Compact Spare Tire Changing a Flat Tire If the Engine Won’t Start Jump Starting If the Engine Overheats Low Oil Pressure Indicator Charging System Indicator Malfunction Indicator Lamp Brake System Indicator Closing the Convertible Top Fuses

...................... .................... ............. ................................ .............. ......... .......... ....... ............... ....... .............................................. .......... .............................. ...................... ..........

Fuse Locations Emergency Towing If Your Vehicle Gets Stuck

Checking and Replacing

. 158
. 159
. 164
. 166
. 167
. 170
. 170
. 171
. 172
. 173
. 174
. 175
. 177
. 179
. 179

157

Main Menust０４／０７／２１　１２：３５：１０　３１Ｓ２Ａ６５０　０１６１　

Compact Spare Tire

Use the compact spare tire as a temporary replacement only. Get your regular tire repaired or replaced, and put it back on your vehicle as soon as you can.

Check the inflation pressure of the compact spare tire every time you check the other tires. It should be inflated to: 60 psi (420 kPa , 4.2 kgf/cm )

158

Follow these precautions:

INDICATOR LOCATION MARK

Never exceed 50 mph (80 km/h).

This tire gives a harsher ride and less traction on some road sur- faces. Use greater caution while driving.

Do not mount snow chains on it.

Do not use your compact spare tire on another vehicle unless it is the same make and model.

Do not use a compact spare tire mounted on a rear wheel; it will damage the limited slip differential (see page

159

).

TREAD WEAR INDICATOR BAR

Replace the tire when you can see the tread wear indicator bars. The replacement should be the same size and design tire, mounted on the same wheel. The spare tire is not designed to be mounted on a regular wheel, and the spare wheel is not designed for mounting a regular tire.

Main MenuTable of Contentsst０４／０７／２１　１２：３５：２１　３１Ｓ２Ａ６５０　０１６２　

If you have a flat tire while driving, stop in a safe place to change it. Drive slowly along the shoulder until you get to an exit or an area that is far away from the traffic lanes.

The vehicle can easily roll off the jack, seriously injuring anyone underneath.

Follow the directions for changing a tire exactly, and never get under the vehicle when it is supported only by the jack.

The compact spare tire is smaller than a standard tire, which will affect the vehicle’s handling. Drive cautiously when this spare is mounted on your vehicle.

The size difference may also cause damage to the rear differential, so do not mount the compact spare on the rear. If either rear tire goes flat, remove the front tire on that same side, mount the compact spare tire on the front, then mount the front tire on the rear.

1.

2.

Park the vehicle on firm, level, and non-slippery ground. Put the transmission in Reverse. Apply the parking brake.

Turn on the hazard warning lights, and turn the ignition switch to LOCK (0). Have your passenger get out of the vehicle while you change the tire.

Changing a Flat Tire

TOOL BOX LID

JACK

3.

Open the trunk. Lift up the tool box lid, and take the jack, wheel wrench, and extension out of the tool box.

Use the jack that came with your vehicle. If you try to raise another vehicle with this jack or use another jack to raise your vehicle, the vehicle or jack can be damaged.

CONTINUED

159

Main MenuTable of Contentsst０４／０７／２１　１２：３５：３０　３１Ｓ２Ａ６５０　０１６３　

Changing a Flat Tire

SPARE TIRE COVER

WHEEL NUT WRENCH

4.

Remove the three clips holding the spare tire cover by pulling the rings straight back. Remove the spare tire cover.

5.

Unscrew the wing bolt, and take the spare tire out of the spare tire shelf.

6.

Loosen each wheel nut 1/2 turn with the wheel nut wrench.

JACKING POINT

7.

Place the jack under the jacking point nearest the tire you need to change. Turn the end bracket clockwise until the top of the jack contacts the jacking point. Make sure the center of the jacking point tab is resting in the jack notch.

160

Main MenuTable of Contentsst０４／０７／２１　１２：３５：３８　３１Ｓ２Ａ６５０　０１６４　

Changing a Flat Tire

EXTENSION

8.

Use the extension and the wheel nut wrench as shown to raise the vehicle until the flat tire is off the ground.

BRAKE HUB

9.

Remove the wheel nuts, then remove the flat tire. Handle the wheel nuts carefully; they may be hot from driving. Place the flat tire on the ground with the outside surface facing up.

10.

Before mounting the spare tire, wipe any dirt off the mounting surface of the wheel and hub with a clean cloth. Wipe the hub carefully; it may be hot from driving.

CONTINUED

161

Main MenuTable of Contentsst０４／０７／２１　１２：３５：４７　３１Ｓ２Ａ６５０　０１６５　

Changing a Flat Tire

11.

Put on the spare tire. Put the wheel nuts back on finger-tight, then tighten them in a crisscross pattern with the wheel nut wrench until the wheel is firmly against the hub. Do not try to tighten them fully.

12.

Lower the vehicle to the ground, and remove the jack.

13.

Tighten the wheel nuts securely in a crisscross pattern. Have the wheel nut torque checked at the nearest automotive service facility. Tighten the wheel nuts to: 80 lbf·ft (108 N·m , 11 kgf·m)

162

Main MenuTable of Contentsst０４／０７／２１　１２：３５：５４　３１Ｓ２Ａ６５０　０１６６　

14.

Remove the tool box from the trunk well, and replace the jack, wheel wrench, and extension in the tool box.

15.

Place the tool box into the spare tire shelf in the trunk.

Changing a Flat Tire

16.

Replace the spare tire cover. Secure it with the three clips. Push each clip in securely, and pivot the ring down flat.

17.

Put the flat tire in the trunk well vertically as shown.

163

Main MenuTable of Contentsst０４／０７／２１　１２：３６：０４　３１Ｓ２Ａ６５０　０１６７　

If the Engine Won’t Start

Diagnosing why the engine won’t start falls into two areas, depending on what you hear when you press the ENGINE START button.

You hear nothing, or almost nothing. The engine’s starter motor does not operate at all, or operates very slowly.

You can hear the starter motor operating normally, or the starter motor sounds like it is spinning faster than normal, but the engine does not start up and run.

164

Nothing Happens or the Starter Motor Operates Very Slowly When you press the ENGINE START button, you do not hear the normal noise of the engine trying to start. You may hear a clicking sound or series of clicks, or nothing at all. Check these things:

Check the transmission interlock. The clutch pedal must be pushed all the way to the floor or the starter will not operate.

Press the ENGINE START button, then release it. If the headlights do not dim, check the condition of the fuses. If the fuses are OK, there is probably something wrong with the electrical circuit for the ignition switch or starter motor. You will need a qualified technician to determine the Emergency problem. (See Towing

on page

179

.)

Turn the ignition switch to ON (II). Turn on the headlights, and check their brightness. If the headlights are very dim or do not come on at all, the battery is discharged. See Jump Starting

on page

166

Main MenuTable of Contentsst０４／０７／２１　１２：３６：１３　３１Ｓ２Ａ６５０　０１６８　

If the Engine Won’t Start

If the headlights dim noticeably or go out when you try to start the engine, either the battery is discharged or the connections are corroded. Check the condition of the battery and terminal connections (see page ). You can then try jump starting the vehicle from a booster battery (see page ).

154

166

The Starter Operates Normally In this case, the starter motor’s speed sounds normal, or even faster than normal, when you press the ENGINE START button, but the engine does not run.

Are you using a properly coded key? An improperly coded key will cause the immobilizer system indicator in the instrument panel to blink rapidly (see page ).

52

Are you using the proper starting Starting the procedure? Refer to Engine 114

on page

Do you have fuel? Check the fuel gauge; the low fuel indicator may not be working.

There may be an electrical problem, such as no power to the fuel pump. Check all the fuses (see page

174

).

If you find nothing wrong, you will need a qualified technician to find the problem. See Towing on page

Emergency 179

165

Main MenuTable of Contentsst０４／０７／２１　１２：３６：２３　３１Ｓ２Ａ６５０　０１６９　

Jump Starting

Although this seems like a simple procedure, you should take several precautions.

A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby.

Keep all sparks, open flames, and smoking materials away from the battery.

166

To jump start your vehicle:

1.

Open the hood, and check the physical condition of the battery. In very cold weather, check the condition of the electrolyte. If it seems slushy or frozen, do not try jump starting until it thaws.

If a battery sits in extreme cold, the electrolyte inside can f reeze. Attempting to jump start with a f rozen battery can cause it to rupture.

2.

Turn off all the electrical accessories: heater, A/C, audio system, lights, etc. Put the transmission in Neutral, and set the parking brake.

The numbers in the illustration show you the order to connect the jumper cables.

3.

＋

) terminal on your

Connect one jumper cable to the positive ( battery. Connect the other end to the positive ( ) terminal on the ＋ booster battery.

Main MenuTable of Contentsst０４／０７／２１　１２：３６：３４　３１Ｓ２Ａ６５０　０１７０　

Jump Starting, If the Engine Overheats

6.

7.

Start your vehicle. If the starter motor still operates slowly, check that the jumper cables have good metal-to-metal contact.

Once your vehicle is running, disconnect the negative cable from your vehicle, then from the booster battery. Disconnect the positive cable from your vehicle, then from the booster battery.

Keep the ends of the jumper cables away from each other and any metal on the vehicle until everything is disconnected. Otherwise, you may cause an electrical short.

If the Engine Overheats The reading on your vehicle’s temperature gauge should stay in the midrange under most conditions. If it reaches the red mark, you should determine the reason (hot day, driving up a steep hill, etc.).

If your vehicle overheats, you should take immediate action. The only indication may be the temperature gauge reading reaching the red mark. Or you may see steam or spray coming from under the hood.

Driving with the temperature gauge reading at the red mark can cause serious damage to your engine.

CONTINUED

167

4.

−

Connect the second jumper cable to the negative ( ) terminal on the booster battery. Connect the other end to the grounding strap as shown. Do not connect this jumper cable to any other part of the engine.

5.

If the booster battery is in another vehicle, have an assistant start that vehicle and run it at a fast idle.

Main MenuTable of Contentsst０４／０７／２１　１２：３６：４３　３１Ｓ２Ａ６５０　０１７１　

If the Engine Overheats

Steam and spray from an overheated engine can seriously scald you.

Do not open the hood if steam is coming out.

168

1.

2.

3.

Safely pull to the side of the road. Put the transmission in Neutral, and set the parking brake. Turn off the all accessories, and turn on the hazard warning indicators.

If you see steam and/or spray coming from under the hood, turn off the engine. Wait until you see no more signs of steam or spray, then open the hood.

If you do not see steam or spray, leave the engine running, and watch the temperature gauge. If the high heat is due to overloading, the engine should start to cool down almost immediately. If it does, wait until the temperature gauge comes down to the midpoint, then continue driving.

4.

If the temperature gauge stays at the red mark, turn off the engine.

5.

6.

Look for any obvious coolant leaks, such as a split radiator hose. Everything is still extremely hot, so use caution. If you find a leak, it must be repaired before you Emergency continue driving (see Towing ). 179

on page

If you don’t find an obvious leak, check the coolant level in the radiator reserve tank. Add coolant if the level is below the MIN mark (see on page

Adding Engine Coolant 134

).

Main MenuTable of Contentsst０４／０７／２１　１２：３６：５１　３１Ｓ２Ａ６５０　０１７２　

If the Engine Overheats

7.

If there was no coolant in the reserve tank, you may need to add coolant to the radiator. Let the engine cool down until the reading reaches the middle of the temperature gauge, or lower, before checking the radiator.

Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.

Always let the engine and radiator cool down before removing the radiator cap.

8.

9.

Using gloves or a large heavy cloth, turn the radiator cap counterclockwise, without pushing down, to the first stop. After the pressure releases, push down on the cap, and turn it until it comes off.

Start the engine, and set the temperature control dial to maximum heat. Add coolant to the radiator up to the base of the filler neck. If you do not have the proper coolant mixture available, you can add plain water. Remember to have the cooling system drained and refilled with the proper mixture as soon as you can.

10.

Put the radiator cap back on tightly. Run the engine, and watch the temperature gauge. If it goes back to the red mark, the engine needs repair (see Towing on page

Emergency 179

).

11.

If the temperature stays normal, check the coolant level in the radiator reserve tank. If it has gone down, add coolant to the MAX mark. Put the cap back on tightly.

169

Main MenuTable of Contentsst０４／０７／２１　１２：３７：０２　３１Ｓ２Ａ６５０　０１７３　

Low Oil Pressure Indicator, Charging System Indicator

Low Oil Pressure Indicator

This indicator should never come on when the engine is running. If it starts flashing or stays on, the oil pressure has dropped very low or lost pressure. Serious engine damage is possible and you should take immediate action.

Running the engine with low oil pressure can cause serious mechanical damage almost immediately. Turn of f the engine as soon as you can saf ely get the vehicle stopped.

1.

2.

3.

4.

170

Safely pull off the road, and shut off the engine. Turn on the hazard warning indicators.

Let the vehicle sit for a minute. Open the hood, and check the oil level (see page ). An engine very low on oil can lose pressure during cornering and other driving maneuvers.

103

If necessary, add oil to bring the level back to the full mark on the dipstick (see page

131

).

Start the engine, and watch the oil pressure indicator. If it does not go out within 10 seconds, turn off the engine. There is a mechanical problem that needs to be repaired before you can continue driving (see 179

Emergency Towing ).

on page

Charging System Indicator

If the charging system indicator comes on brightly

when the engine is running, the battery is not being charged.

Immediately turn off all electrical accessories. Try not to use other electrically operated controls such as the power windows. Keep the engine running; starting the engine will discharge the battery rapidly.

Go to a service station or garage where you can get technical assistance.

Main MenuTable of Contentsst０４／１０／２２　１７：１１：２２　３１Ｓ２Ａ６５０　０１７４　

If this indicator comes on while driving, it means one

of the engine’s emissions control systems may have a problem. Even though you may feel no difference in your vehicle’s performance, it can reduce your fuel economy and cause increased emissions. Continued operation may cause serious damage.

If you have recently refueled your vehicle, the indicator coming on could be due to a loose or missing fuel fill cap. Tighten the cap until it clicks at least three times. Tightening the cap will not turn the indicator off immediately; it takes at least three days of normal driving.

Malfunction Indicator Lamp

If the indicator comes on repeatedly, even though it may go off as you continue driving, have your vehicle checked by a dealer as soon as possible.

If your vehicle battery has been disconnected or gone dead, these codes are erased. It takes at least three days of driving under various conditions to set the codes again.

To check if they are set, turn the ignition to ON (II), without starting the engine. The malfunction indicator lamp will come on for 20
seconds. If it then goes off, the readiness codes are set. If it blinks five times, the readiness codes are not set. If possible, do not take your vehicle for a state emissions test until the readiness codes are set. Refer to for more information (see page

State Emissions Testing 192

).

If you keep driving with the Malf unction Indicator Lamp on, you can damage your vehicle’s emissions controls and the engine. Those repairs may not be covered by your vehicle’s warranties.

Readiness Code Your vehicle has certain ‘‘readiness codes’’ that are part of the on-board diagnostics for the emissions systems. In some states, part of the emissions testing is to make sure these codes are set. If they are not set, the test cannot be completed.

171

Main MenuTable of Contentsst０４／０７／２１　１２：３７：１８　３１Ｓ２Ａ６５０　０１７５　

Brake System Indicator

However, if the brake pedal does not feel normal, you should take immediate action. A problem in one part of the system’s dual circuit design will still give you braking at two wheels. You will feel the brake pedal go down much farther before the vehicle begins to slow down, and you will have to press harder on the pedal.

Slow down by shifting to a lower gear, and pull to the side of the road when it is safe. Because of the long distance needed to stop, it is hazardous to drive the vehicle. You should have it towed and repaired as soon as possible (see Towing 179

Emergency ).

on page

If you must drive the vehicle a short distance in this condition, drive slowly and carefully.

U.S.

Canada

The brake system indicator normally comes on when you turn the ignition switch to ON (II), and as a reminder to check the parking brake. It will stay on if you do not fully release the parking brake.

If the brake system indicator comes on while driving, the brake fluid level is probably low. Press lightly on the brake pedal to see if it feels normal. If it does, check the brake fluid level the next time you stop at a service station (see page

139

).

If the fluid level is low, take your vehicle to a dealer, and have the brake system inspected for leaks or worn brake pads.

172

Main MenuTable of Contentsst０４／１０／２２　１７：１１：３２　３１Ｓ２Ａ６５０　０１７６　

If the electric motor will not close the convertible top, do the following.

1.

2.

Check the fuse for the convertible top motor (see page ). If the fuse is blown, replace it with one of the same or lower rating.

174

Try closing the convertible top. If the new fuse blows immediately or the convertible top still does not operate, you can close it manually.

Closing the Convertible Top

CONNECTOR

3.

Locate the electrical connector for the convertible top motor. It is under the lower corner of the dashboard on the passenger’s side. Disconnect the connector by pushing the tab and pulling the connector down.

4.

Holding each corner of the convertible top, raise the top and push it forward as far as it will go.

5.

Follow steps 4 through 6 of the closing procedure on page

65

173

Main MenuTable of Contentsst０４／１０／２２　１７：１１：３９　３１Ｓ２Ａ６５０　０１７７　

Fuses

The vehicle’s fuses are contained in three fuse boxes.

UNDER-HOOD (PRIMARY)

UNDER-HOOD (AUXILIARY)

INTERIOR

The interior fuse box is underneath the dashboard on the driver’s side.

The primary under-hood fuse box is on the passenger’s side next to the battery. To open it, push the two tabs as shown.

The auxiliary fuse box is on the driver’s side, near the brake fluid reservoir. To open it, push the tab on each side, and remove the lid.

174

Main MenuTable of Contentsst０４／０７／２１　１２：３７：４５　３１Ｓ２Ａ６５０　０１７８　

177

and

Checking and Replacing Fuses If something electrical in your vehicle stops working, check for a blown fuse first. Determine from the chart on pages , or the diagram on the fuse box lid, which fuse or fuses control that device. Check those fuses first, but check all the fuses before deciding that a blown fuse is the cause. Replace any blown fuses, and check if the device work.

178

Fuses

4.

Check the smaller fuses in the under-hood fuse boxes and all the fuses in the interior fuse box by pulling out each one with the fuse puller provided in the primary under-hood fuse box.

BLOWN

1.

Turn the ignition switch to LOCK (0). Make sure the headlights and all other accessories are off.

2.

Remove the cover from the fuse box.

3.

Check each of the large fuses in the primary under-hood fuse box by looking through the top at the wire inside. Removing these fuses requires a Phillips-head screwdriver.

CONTINUED

175

Main MenuTable of Contentsst０４／０７／２１　１２：３７：５４　３１Ｓ２Ａ６５０　０１７９　

Fuses

BLOWN

5.

Look for a burned wire inside the fuse. If it is burned, replace it with one of the spare fuses of the same rating or lower.

176

If you cannot drive the vehicle without fixing the problem, and you do not have a spare fuse, take a fuse of the same rating or a lower rating from one of the other circuits. Make sure you can do without that circuit temporarily (such as the accessory power socket or radio).

If you replace the blown fuse with a spare fuse that has a lower rating, it might blow out again. This does not indicate anything wrong. Replace the fuse with one of the correct rating as soon as you can.

Replacing a f use with one that has a higher rating greatly increases the chances of damaging the electrical system. If you do not have a replacement f use with the proper rating f or the circuit, install one with a lower rating.

6.

If the replacement fuse of the same rating blows in a short time, there is probably a serious electrical problem with your vehicle. Leave the blown fuse in that circuit, and have your vehicle checked by a qualified mechanic.

If the radio fuse is removed, the audio system will disable itself. The next time you turn on the radio you will see ‘‘Code’’ in the frequency display. Use the preset buttons to enter the five-digit code (see page 94

).

Main MenuTable of Contentsst０４／０７／２１　１２：３８：０２　３１Ｓ２Ａ６５０　０１８０　

IINNTTEERRIIOORR FFUUSSEE BBOOXX

No. Amps.

Circuits Protected

No. Amps.

Circuits Protected

Fuse Locations

10
11
12
13

7.5 A

15 A − − 10 A 20 A 7.5 A 15 A 7.5 A

15 A 7.5 A 15 A 10 A

Windshield Wiper, Auto Stop Signal Washer Motor Not used Not used Accessory Socket Windshield Wiper Turn signal Light ACG Instrument Light, Backup Lights Ignition Coil Engine Start Fuel Pump, SRS SRS

＊

: Canadian Model

14
15
16
17
18
19
20
21

22
23
24
25
26
27

10 A 10 A 7.5 A 7.5 A 10 A 15 A 7.5 A 7.5 A

7.5 A 20 A 20 A − − −

＊

Daytime Running Lights Keyless Entry Back-up Interior Light Small Lights Radio Starter Signal Heater Control, Cooling Fan Relay Power Mirrors Right Power Window Left Power Window Not used Not used Not used

CONTINUED

177

Main MenuTable of Contentsst０４／０７／２１　１２：３８：１３　３１Ｓ２Ａ６５０　０１８１　

Fuse Locations

UNDER-HOOD FUSE BOXES (PRIMARY FUSE BOX)

(AUXILIARY FUSE BOX)

178

No. Amps.

Circuits Protected

No. Amps.

Circuits Protected

14
15
16
17
18
19
20
21
22
23
24
25

− 20 A 15 A 10 A 20 A − 15 A 20 A 20 A 30 A 100 A 40 A

Magnetic Clutch Relay Right Headlight ACG S Hazard Warning Lights Cooling Fan Not used Stop Left Headlight ABS F/S ABS Motor Battery IG1 Main

10
11
12
13

− − − 40 A 20 A − 30 A 20 A 40 A 20 A − − −

Lighting 1 Relay Lighting 2 Relay Horn Relay