2007 Honda Ridgeline Owners Manual

will not have VSA traction and stability enhancement. See page for more information on the 210
VSA system.

VSA Activation Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. For more information, see page

210

This indicator has three functions:

1.

2.

3.

Itcomesonasareminderthatyou have turned off the vehicle stability assist (VSA) system.

It flashes when VSA is active (see page

210

).

It comes on along with the VSA system indicator if there is a problem with the VSA system.

Instrument Panel Indicators

Maintenance Minder Indicator

This indicator reminds you that it is time to take your vehicle in for scheduled maintenance. The maintenance main items and sub items will be displayed in the information display. See page more information on the maintenance minder.

235

for

This indicator goes off when your dealer resets it after completing the required maintenance service.

67

Main MenuTable of ContentsstTire Pressure Monitor

This monitor normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. While driving, the appropriate tire indicator will come on, along with the low tire pressure indicator, if a tire is extremely underinflated or has suddenly lost Low Tire Pressure pressure. See Indicator indicator comes on.

for what to do if this

Tire Pressure Monitoring System (TPMS) Indicator This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.

If this indicator comes on and stays on at any other time, or if it does not come on when you turn the ignition switch to the ON (II) position, there is a problem with the TPMS. With this indicator on, the low tire pressure indicator and the tire pressure monitor will not come on when a tire loses pressure. Take the vehicle to your dealer to have the system checked.

Instrument Panel Indicators

Low Tire Pressure Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. If it comes on while driving, it indicates that one or more of your vehicle’s tires are extremely low on pressure.

If this happens, pull to the side of the road when it is safe, check which tire has lost the pressure on the tire pressure monitor, and determine the cause. If it is because of a flat tire, replace the flat tire with the compact spare (see page ), and have the flat tire repaired as soon as possible. If two or more tires are underinflated, call a professional towing service (see page 204

for more information.

). Refer to page

274

296

68

Main MenuTable of ContentsstIn-Bed Trunk Open Indicator

This indicator reminds you that the In-Bed Trunk is open. If you do not close it, the indicator stays on for about 3 minutes. See page for more information.

95

Bed Lights On Indicator

This indicator reminds you that the bed lights are on. With the shift lever in the Park position, they come on when you push the light switch on the dashboard, swing open the tailgate, or open the In-Bed Trunk.

If you turn the ignition switch to the ACCESSORY (I) or LOCK (0) position without turning off the bed lights, this indicator will remain on, andthengooffafter20minutes.See page for more information.

120

Instrument Panel Indicators

Back Window Open Indicator

This indicator reminds you that the back window is not completely closed when you turn the ignition switch from the ON (II) position to the ACCESSORY (I) or the LOCK (0) position. With the ignition switch in the ACCESSORY (I) position, it goes off after about 30 seconds. With the ignition switch in the LOCK (0) position, it goes off after about 3
minutes.

If you remove the ignition key, turn off the lights, and open the driver’s door without closing the back window, you will hear five beeps and see the indicator blink. If you do not close the back window before the beeper stops, the indicator stops blinking but remains on. It will go off after about 3 minutes. See page 106

for more information.

69

Main MenuTable of ContentsstGauges

TACHOMETER

SPEEDOMETER

TEMPERATURE GAUGE

FUEL GAUGE

ODOMETER/ TIGHTEN FUEL CAP MESSAGE

SELECT BUTTON

OUTSIDE TEMPERATURE INDICATOR

INFORMATION DISPLAY

TRIP METER

RESET BUTTON

U.S. model is shown.

70

To switch the information display between the odometer, trip meter and outside temperature (if equipped), and engine oil life and maintenance service items, press the SELECT button repeatedly.

Odometer This shows the total distance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S. federal law and Canadian provincial regulations to disconnect, reset, or alter the odometer with the intent to change the number of miles or kilometers indicated.

Main MenuTable of ContentsstGauges

When you turn the ignition switch to the ON (II) position, the meter you last selected is displayed.

To reset a trip meter, display it, and then press and hold the RESET button until the number resets to ‘‘0.0’’. Both trip meters will reset if the vehicle’s battery goes dead or is disconnected. And both continue to track mileage, even when only one is displayed.

Fuel Gauge This shows how much fuel you have. It may show slightly more or less than the actual amount. The needle returns to the bottom after you turn off the ignition.

Avoid driving with an extremely low f uel level. Running out of f uel could cause the engine to misf ire, damaging the catalytic converter.

Trip Meter This meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it.

SELECT BUTTON

RESET BUTTON

There are two trip meters: TRIP A and TRIP B. Switch between these displays by pressing the SELECT button repeatedly. Each trip meter works independently, so you can keep track of two different distances.

71

Main MenuTable of ContentsstGauges

Temperature Gauge This shows the temperature of the engine’s coolant. During normal operation, the pointer should rise to about the middle of the gauge. In severe driving conditions, the pointer may rise to the upper zone. If it reaches the red (hot) mark, pull safely to the side of the road. For instructions and precautions on checking the engine’s cooling system, see page

286

Outside Temperature Indicator Ifequipped This indicator displays the outside temperature in Fahrenheit (U.S. models) or Centigrade (Canadian models).

The temperature sensor is in the front bumper. Therefore, the temperature reading can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic. This can cause an incorrect temperature reading when your speed is under 19 mph (30 km/h).

The sensor delays the indicator update until it reaches the correct outside temperature. This may take several minutes.

If the outside temperature is incorrectly displayed, you can adjust it up 5°F in U.S. models ( 3°C in Canadian models) warmer or cooler.

±

±

72

NOTE: The temperature must be stabilized before doing this procedure.

To adjust the outside temperature indicator, make sure the outside temperature indicator is shown in thedisplay,thenpressandholdthe RESET button for 10 seconds (the TRIP A or B is also reset). The following sequence will appear for 1
5, 4, secondeach:0,1,2,3,4,5, − − − − − −

− − 3, 2, 1, 0 (U.S.) or 0, 1, 2, 3, 3, 2, 1, 0 (Canada).

When it reaches the desired value, release the RESET button. You should see the new outside temperature displayed.

In certain weather conditions, temperature readings near freezing (32°F, 0°C) could mean that ice is forming on the road surface.

Main MenuTable of ContentsstTighten Fuel Cap Message If your fuel fill cap is loose or missing, a ‘‘TIGHTEN FUEL CAP’’ message appears on the information display after you start the engine. Turn the engine off, and confirm the fuel cap is installed. If it is, loosen it, then retighten it until it clicks at least once. When you restart the engine, the message appears again. The message goes off after several days of normal driving once you tighten or replace the fuel cap. To scroll to another message, press the select button.

If the system still detects a leak in your vehicle's evaporative emissions system, the malfunction indicator lamp (MIL) comes on. If the fuel cap was not already tightened, turn the engine off, and check or retighten the fuel cap until it clicks at least once. The MIL goes off after several days of normal driving once the cap is tightened or replaced. If the MIL does not go off, have your vehicle inspected by a dealer. For more information, see page 289.

Gauges

Maintenance Minder Display The information display in the instrument panel shows you the engine oil life and maintenance service items when the ignition switch is in the ON (II) position. This information helps to keep you aware of the periodic maintenance your vehicle needs for continued trouble- free driving. Refer to page more information.

235

for

73

Main MenuTable of ContentsstControls Near the Steering Wheel

MOONROOF SWITCH ＊ (P.108)

INSTRUMENT PANEL BRIGHTNESS

(P.78)

SHIFT LEVER (P.197)

VTM-4 LOCK

(P.203)

MULTI-CONTROL LEVER (WINDSHIELD WIPERS/ WASHERS/TURN SIGNALS/ HEADLIGHT HIGH BEAMS) (P.75) BED LIGHT SWITCH (P.120)

HEADLIGHT CONTROL DIAL

(P.76)

VEHICLE STABILITY ASSIST (VSA) SYSTEM OFF SWITCH (P.211)

CRUISE BUTTON (P.165)

REMOTE AUDIO CONTROLS

＊

(P.161)

HORN ＊

STEERING WHEEL ADJUSTMENT

(P.79)

CRUISE CONTROLS (P.165)

Vehicle with navigation system is shown.

To use the horn, press the pad around the ‘‘H’’ logo. If equipped.

＊ ＊ 74

SELECT BUTTON (P.70) RESET BUTTON (P.70) PASSENGER AIRBAG OFF INDICATOR (P.29) HAZARD WARNING BUTTON (P.79)

INTERIOR LIGHT CONTROL SWITCH (P.118)

SEAT HEATERS ＊ (P.104)

Main MenuTable of ContentsstThe multi-control lever has many functions, including windshield wipers and washers, turn signals, headlight high beams, and headlight high beam flashing.

To select a position, turn the rotary switch, push the button on the end of the lever, or push the lever up, down, forward, or backward.

OFF:

The wipers are not activated.

INT:

The length of the wiper interval is varied automatically according to the vehicle’s speed.

Vary the delay by turning the INT TIME ring. If you turn it to the shortest delay, the wipers change to low speed when the vehicle speed exceeds 12 mph (20 km/h).

Multi-Control Lever

LO

−

The wipers run at low speed.

HI

−

The wipers run at high speed.

MIST:

The wipers run at high speed until you release the lever.

Windshield Washer:

Push the button on the end of the multi-control lever. The washers spray until you release the button. The wipers run at low speed, then complete one more sweep after you release the button.

75

1. 2. 3. 4. 5. 6. 7. 8. 9. 10.

OFF INT: Intermittent INT TIME ring LO: Low speed HI: High speed MIST Windshield washer (spray nozzles) Turn signal High beams Flash high beams

Main MenuTable of ContentsstMulti-Control Lever, Headlights

Headlight Control Dial

−

Turn Signal Push down on the multi-control lever to signal a left turn and up to signal a right turn. To signal a lane change, push lightly on the lever and hold it. The lever will return to center when you release it or complete a turn.

−

High Beams To turn on the high beams, push the multi-control lever forward until you hear a click. The blue high beam indicator will come on (see page to return to the low beams.

). Pull the lever back

65

To flash the high beams, pull the lever back lightly, then release it. The high beams will stay on as long as you hold the lever back.

1. 2. 3.

OFF Parking and indicator lights Headlights

AutomaticHeatedWiperZone Your vehicle has heating wires at the bottom of the windshield to help heat the wiper blades and the windshield. If the outside temperature is near freezing, the heater turns on automatically when you turn the ignition switch to the ON (II) position. The heater turns off automatically when the outside temperature is above freezing.

This function helps to increase wiper performance when the wiper arms sit in the parked position in snowy or icy conditions.

76

Main MenuTable of ContentsstAutomatic Lighting Off Feature The automatic lighting off feature turns off the headlights, all other exterior lights, and the instrument panel lights within 15 seconds of removing the key from the ignition switch and closing the driver’s door.

This feature activates if you leave the headlight control dial in the ‘‘ the key, then open and close the driver’s door.

’’ position, remove

’’ or ‘‘

−

Turning the dial to ’’ position turns on the

Headlights the ‘‘ parking lights, taillights, instrument panel lights, and license plate lights.

’’

Turning the dial to the ‘‘ position turns on the headlights. If you leave the lights on and remove the key from the ignition switch, you will hear a reminder chime when you open the driver’s door.

’’ or

’’ position, the lights on

When the dial is in the ‘‘ ‘‘ indicator comes on as a reminder. This indicator stays on if you leave the lights on and turn the ignition switch to the ACCESSORY (I) or LOCK (0) position.

Headlights

If you remove the key from the ignition switch with the headlight control dial on, but do not open the door, the lights will turn off after 10
minutes.

The lights will turn on again when you unlock or open the driver’s door. If you unlock the door, but do not open it within 15 seconds, the lights go off. With the driver’s door open, you will hear a lights-on reminder chime.

77

Main MenuTable of ContentsstHeadlights, Instrument Panel Brightness

Daytime Running Lights Canadianmodelsonly With the headlight control dial off, the high beam headlights and the high beam indicator come on with reduced brightness when you turn the ignition switch to the ON (II) position and release the parking brake. They remain on until you turn the ignition switch off, even if you set the parking brake.

The headlights revert to normal operation when you turn them on with the headlight control dial.

78

Instrument Panel Brightness

If you do not insert the key in the ignition switch after opening the driver’s door, the illumination turns off about 30 seconds after you close the door.

If you insert the key but do not turn the ignition switch to the ON (II) position, the illumination turns off in about 10 seconds.

The instrument panel brightness is dimmed when you turn the headlight control dial to the ‘‘ ‘‘ night. To cancel it, turn the instrument panel brightness control dial upward fully until you hear a click.

’’ position to reduce glare at

’’ or

INSTRUMENT PANEL BRIGHTNESS CONTROL DIAL

The dial on the instrument panel controls the brightness of the instrument panel lights and the console compartment light. Turn the dial to adjust the brightness.

The instrument panel will illuminate with reduced brightness when you unlock and open the driver’s door. The brightness will increase and go to a normal level when you insert the key in the ignition switch.

Main MenuTable of ContentsstHazard Warning Button, Steering Wheel Adjustment

Hazard Warning Button

Steering Wheel Adjustment Make any steering wheel adjustment before you start driving.

Push the button to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both turn indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.

1.

2.

Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.

Adjust the steering wheel only when the vehicle is stopped.

3.

Push the lever up to lock the steering wheel in position.

Push the lever on the left side of the steering column all the way down.

4.

Make sure you have securely locked the steering wheel in place by trying to move it up and down.

Move the steering wheel so it points toward your chest, not toward your face. Make sure you can see the instrument panel gauges and indicators.

79

Main MenuTable of ContentsstKeys

KEY NUMBER TAG

MASTER KEY WITH REMOTE TRANSMITTER

VALET KEY (LIGHT GRAY)

You should have received a key number tag with your keys. You will need this key number if you ever have to get a lost key replaced. Use only Honda-approved key blanks.

These keys contain electronic circuits that are activated by the immobilizer system. They will not work to start the engine if the circuits are damaged.

The master key fits all the locks on your vehicle. The valet key works only in the ignition and the driver’s door lock. You can keep the glove boxlockedwhenyouleaveyour vehicle and the valet key at a parking facility.

Protect the keys from direct sunlight, high temperature, and high humidity.

Donotdropthekeysorsetheavy objects on them.

Keep the keys away from liquids. If they get wet, dry them immediately with a soft cloth.

You can also keep the In-Bed Trunk locked by using the main switch in the glove box (see page

97

).

80

Main MenuTable of ContentsstImmobilizer System

The immobilizer system protects your vehicle from theft. If an improperly-coded key (or other device) is used, the engine’s fuel system is disabled.

When you turn the ignition switch to the ON (II) position, the immobilizer system indicator should come on for a few seconds, then go off. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to the LOCK (0) position, remove the key, reinsert it, and turn the ignition switch to the ON (II) position again.

The system may not recognize your key’s coding if another immobilizer key or other metal object (i.e. key fob) is near the ignition switch when you insert the key.

If the system repeatedly does not recognize the coding of your key, contact your dealer.

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle undrivable.

Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

If you have lost your key and cannot start the engine, contact your dealer.

ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

81

Main MenuTable of ContentsstIgnition Switch

The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), and START (III).

82

−

Use this position

START (III) only to start the engine. The switch returns to the ON (II) position when you let go of the key.

You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or the ACCESSORY (I) position and open the driver’s door. Remove the key to turn off the beeper.

The shift lever must be in Park(P) before you can remove the key from the ignition switch.

−

You can insert or

LOCK (0) remove the key only in this position. To turn the key, the shift lever must be in Park, and you must push the key in slightly.

If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key.

−

You can

ACCESSORY (I) operate the audio system and the accessory power sockets in this position.

−

This is the normal key

ON (II) position when driving. Several of the indicators on the instrument panel come on as a test when you turn the ignition switch from the ACCESSORY (I) to the ON (II) position.

Main MenuTable of ContentsstPower Door Locks

LOCK TAB

The lock tab on each door locks and unlocks that door. Pulling up on the driver’s door lock tab only unlocks the driver’s door. To unlock the driver’s door and the In-Bed Trunk from the outside, turn the key and release it. If you turn it again, all the doors unlock.

Youcanopenorclosetheside windows by using the key in the driver’s door (see page

107

).

MASTER DOOR LOCK SWITCH

Tolockal ldoorsandth eIn-Bed Trunk (the tailgate does not lock), push the front of the master doorlock switch on either front door, pressthe lock tab down on the driver’ sdoor,or use the key on the outsidelocko nthe driver’ sdoor.

Pushingtherearofeithermaster doorlockswitchwillunlockallofthe doorsandth eIn-BedTrunk.

Door Locks

To lock any passenger’s door when getting out of the vehicle, push the lock tab down, and close the door. To lock the driver’s door, remove the key from the ignition switch, and push the lock tab down, or push the front of the master switch, then close the door.

Lockout Prevention Withthed river’ sdooropenandthe keyintheignition,bothm asterdoor lockswitches will not lock, but they will unlock. The lock feature is not disabled if the driver’s door is closed. Pushing the front of the switchonthe open passenger’s door willlockall doors and the In-Bed Trunk.

Thisvehiclehasautodoorlocking/ 84
unlockingfeatures.Seepagefor howtosetthem.

83

Main MenuTable of ContentsstDoor Locks

Childproof Door Locks

LOCK LEVER

The childproof door locks are designed to prevent children seated in the rear from accidentally opening the rear doors. Each rear door has a lock lever near the edge. With the lever in the LOCK position, the door cannot be opened from inside regardless of the position of the lock tab. To open the door, pull the lock tab up, and use the outside door handle.

84

Automatic (Auto) Door Locking/ Unlocking Your vehicle has customizable settings for the doors to automatically lock and unlock. Make all settings before you start driving.

With the auto door locking and unlocking, the In-Bed Trunk also locks and unlocks (the tailgate does not lock). Auto Door Locking The auto door locking feature has three possible settings:

The doors lock whenever you move the shift lever out of the Park (P) position.

The doors lock when the vehicle speed reaches 9 mph (15 km/h).

The auto door locking is deactivated all the time.

To program the Park Lock mode: Locksalldoorswhentheshiftleveris movedoutofPark(P).

1.

Make sure the shift lever is in the Park (P) position.

2.

3.

Apply the parking brake, and close the driver’s door.

Turn the ignition switch to the ON (II) position (do not start the engine).

Main MenuTable of ContentsstTo program the Drive Lock mode: Locksalldoorswhenthevehicle’sspeed reachesabout9mph(15km/h).

4.

Push and hold the front of the master door lock switch on the driver’ s door. You will hear a clicking sound, and after about 5
seconds, you will hear another clicking sound.

5.

Release the switch, and turn the ignition switch to the ACCESSORY (I)

position within 5 seconds.

4.

5.

6.

Door Locks

Push and hold the brake pedal, then move the shift lever out of Park (P).

Push and hold the front of the master door lock switch on the driver’ s door. You will hear a clicking sound, and after about 5
seconds, you will hear another clicking sound.

Release the switch, and turn the ignition switch to the (I)

position within 5 seconds.

ACCESSORY

1.

2.

3.

Make sure the shift lever is in the Park (P) position.

Apply the parking brake, and close the driver’s door.

Turn the ignition switch to the ON (II) position (do not start the engine).

7. Move the shift lever to PARK (P).

CONTINUED

85

Main MenuTable of ContentsstDoor Locks

To turn off the Auto Lock modes:

4.

5.

1.

2.

Make sure the shift lever is in the Park (P) position.

Apply the parking brake, and open the driver’s door.

3. Turn the ignition switch to the ON (II) position (do not start the engine).

86

Push and hold the front of the master door lock switch on the driver’s door. You will hear a clicking sound after about 5
seconds.

Auto Door Unlocking The auto door unlocking feature has three modes (Park Unlock, Ignition Switch, and Deactivated), with five possible settings:

Release the switch, and turn the ignition switch to the (I)

position within 5 seconds.

ACCESSORY

Park Unlock mode:

The driver’ s door and then In-Bed Trunk unlocks whenever you move the shift lever to the PARK (P) position. All doors and the In-Bed trunk unlocks whenever you move the shift lever to the PARK (P) position.

Ignition Switch mode:

The driver’s door and the In-Bed Trunk unlocks whenever you turn the ignition switch to the LOCK (0) position. All doors and the In-Bed Trunk unlocks whenever you turn the ignition switch to theLOCK (0) position.

Deactivated:

The auto door unlocking settings are deactivated.

Main MenuTable of ContentsstPush and hold the rear of the master door lock switch on the driver’s door. You will hear a clicking sound. Continue to hold down the switch: −Until you hear a second click

about 5 seconds) to

(after activate the driver’s door unlock feature.

−

Or, until you hear a third click (after about 10 seconds) to activate the all door unlock feature.

Release the switch, and turn the ignition switch to the (I)

position within 5 seconds.

ACCESSORY

3.

4.

To program the Park Unlock mode: Unlock mode: Unlocksdriver’sdoororalldoorswhen the shift lever is moved to Park (P).

1.

2.

Make sure the shift lever is in Park (P), and close the driver’s door.

Turn the ignition switch to the ON (II) position.

＊ If equipped

Door Locks

To program the Ignition Switch Unlock mode: Unlocksdriver’ sdoororalldoorswhen theignitionswitchisoutoftheON(II) position.*

1.

2.

Make sure the shift lever is in the Park (P) position.

Apply the parking brake, and close the driver’s door.

3. Turn the ignition switch to the ON (II) position (do not start the engine). CONTINUED 87

Main MenuTable of Contentsst4.

5.

Push and hold the rear of the master door lock switch on the driver’s door. You will hear a clicking sound, and after about 5
seconds, you will hear another clicking sound. Release the switch, and turn the ignition switch to the (I)

position within 5 seconds.

ACCESSORY

Door Locks

4. T o turn off the door unlock

Push and hold the brake pedal, then move the shift lever out of Park (P).

modes:

5.

6.

Push and hold the rear of the master door lock switch on the driver’s door. You will hear a clicking sound. Continue to hold down the switch: −Until you hear a second click

about 5 seconds) to

(after activate the driver’s door unlock feature.

−

Or, until you hear a third click (after about 10 seconds) to activate the all door unlock feature.

Release the switch, and turn the ignition switch to the (I)

position within 5 seconds.

ACCESSORY

7. Move the shift lever to PARK (P).

88

1.

2.

3.

Make sure the shift lever is in the Park (P) position.

Apply the parking brake, and open the driver’s door.

Turn the ignition switch to the ON (II) position (do not start the engine).

Main MenuTable of ContentsstLED

LOCK BUTTON

UNLOCK BUTTON

PANIC BUTTON

−

LOCK Press this button once to lock all doors and the In-Bed Trunk. Some exterior and interior lights will flash once. WhenyoupushLOCKtwicewithin5
seconds,youwillheara hornto verifythatthedoorsa ndIn-Bed Trunkarelockedandthesecurity system(ifequipped)hasset.This buttondoesnotworkifan notfullyclosedorthekeyisinthe ignitionswitch.

ydooris

−

Pressthisbuttononce

UNLOCK tounlockthedriver’ sdoorandthe In-BedTrunk.Pushittwiceto unlock theremainingdoors. If you press the button twice and hold for 3–5 seconds, the side windows will roll down (see page 107). Some exterior and interior lights will flash twice each time you push the button.

When you press the UNLOCK button, the front and rear individual map lights, depending on the interior light control switch position, will come on (see page ). If you do not open any door, the lights stay on for about 30 seconds, then go out. If you relock the doors and the In-Bed Trunk with the remote transmitter before 30 seconds have elapsed, the lights will go off immediately.

118

Remote Transmitter

If you do not open any door within 30
seconds, the doors automatically relock, and the security system sets (if equipped). The UNLOCK button does not work when the key is in the ignition switch.

You can also open all side windows from outside the vehicle with the 107
remote transmitter (see page

).

−

Press and hold this

PANIC button for about 1 second to attract attention; the horn will sound and the exterior lights will flash for about 30 seconds. To cancel panic mode, press any other button on the remote transmitter, or turn the ignition switch to the ON (II) position. Panic mode does not work when the key is in the ignition switch.

89

Main MenuTable of ContentsstRemote Transmitter

Remote Transmitter Care

Avoid dropping or throwing the transmitter.

Protect the transmitter from extreme temperature.

Do not immerse the transmitter in any liquid.

If you lose a transmitter, the replacement needs to be reprogrammed by your dealer.

90

Replacing the Transmitter Battery

BATTERY

SCREW

If it takes several pushes on the button to lock or unlock the doors, replace the battery as soon as possible. Battery type: CR1616

2.

3.

To replace the battery:

1.

Remove the screw at the base of the transmitter with a small Phillips-head screwdriver.

Separate the transmitter by prying its middle seam with your fingernail.

Inside the transmitter, separate the inner cover from the keypad by releasing the two tabs on the cover.

Main MenuTable of Contentsst4.

Remove the old battery from the back of the inner cover, and insert a new battery into the back of the cover with the

side facing down.

＋

5.

Install the parts in reverse order.

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

Remote Transmitter

91

Main MenuTable of ContentsstTo Drop Open the Tailgate

UPPER HANDLE

Before you open the tailgate a different way (dropped open, and then swung open), make sure it is fully closed.

Make sure all passengers and objects are clear of the tailgate before opening and closing it, and make sure the tailgate is closed securely before driving.

To drop open the tailgate, pull up the upper handle, then pull down the tailgate. To close the tailgate, push firmly up until it latches.

Dual-Action Tailgate

You can open the tailgate two different ways:

Drop it open by using the upper handle.

Swing it open by using the right lower handle.

NOTE: As a safety feature, the upper handle is disabled if you do not fully close the tailgate after it is swung open. And the lower handle is disabled if you do not fully close the tailgate after it is dropped open.

92

Main MenuTable of ContentsstThe dropped open tailgate can be used as an extended pickup bed. Make sure to secure the items in the pickup bed, and do not exceed the maximum allowable weight on the tailgate(seepage

189

).

To Swing Open the Tailgate

To turn the bed lights on or off, use the bed light switch on the dashboard (see page ).

120

HANDLE

To swing open the tailgate, first make sure it is fully closed, then pull up the right lower handle, and swing the tailgate to the left. To close, swing the tailgate back, and push it firmly until it is latched.

Before opening or closing the tailgate, check that passengers, especially children, are not in the tailgate’s path.

Dual-Action Tailgate

Do not drive with the tailgate swung open. This could damage the tailgate.

Swinging the tailgate open or closed while anyone is in its path can cause serious injury.

Make sure all passengers are clear of the tailgate’s path before opening or closing it.

CONTINUED

93

Main MenuTable of ContentsstDual-Action Tailgate

Do not allow anyone to hang on the swung open tailgate. This could damage the tailgate.

Do not leave the tailgate swung open. The tailgate may swing and shut accidentally. This could cause serious injuries.

Thebedlightscomeonwhenyou swing open the tailgate. You can also turn the bed lights on or off by pushing the bed light switch on the dashboard (see page

120

).

TailgateOpenIndicator

This indicator is in the door and tailgate open monitor on the instrument panel. It comes on when the tailgate is swung open or it is not completely closed. This indicator worksevenifthekeyisnotinthe ignition switch.

If the tailgate is swung open or not closed tightly when the ignition switch is in the ON (II) position, you will hear six beeps and see the indicator blinking. The indicator stays on until you close the tailgate. The beeper also sounds and the indicator blinks when you move the shift lever out of the Park or neutral position.

94

If you do not fasten the seat belt, you first hear the seat belt reminder alarm, then the tailgate reminder beeper sounds.

The indicator does not monitor the tailgate when it is dropped open.

Loading Cargo See page for information on cargo loading and weight limits.

186

You can also store and lock items in the In-Bed Trunk (see page

95

).

Main MenuTable of ContentsstRELEASE BUTTON

YoucanopentheIn-BedTrunktwo different ways:

Push the release button on the lower right side of the In-Bed Trunk lid when the driver’s door is unlocked.

Usethemasterkeytoopenthe In-Bed Trunk when the driver’s door is locked.

To close the In-Bed Trunk, lower the lid, then press down on the back edge.

When the In-Bed Trunk is closed securely, it can be locked or unlocked along with the power door locks (see page

83

).

In-Bed Trunk

TM

If your vehicle’s battery is disconnected or goes dead, the release button on the In-Bed Trunk lid is disabled. To open the In-Bed Trunk, use the master key.

Thebedlightscomeonwhenyou open the In-Bed Trunk. You can also turn the bed lights on or off by pushing the bed light switch on the dashboard (see page

120

).

You can store items in the In-Bed Trunk up to 300 lbs (136 kg). Do not exceed this weight limit, or you may damage the In-Bed Trunk. See page 186
for information on loading cargo and weight limits.

To store items separately in the In-Bed Trunk, optional divider guides are available from your dealer.

CONTINUED

95

Main MenuTable of ContentsstIn-Bed Trunk

TM

To avoid damaging the key and key cylinder of the In-Bed Trunk lid, do notclosethetailgatewhenthekeyis in the lid.

To avoid damaging the seal on the In-Bed Trunk lid, remove any debris from the lid’s mating surface before you close it.

Emergency Opener

To avoid damaging the In-Bed Trunk lid, and to prevent items from being thrown about the vehicle and possibly hurting someone in an accident or sudden stop, be sure the In-Bed Trunk lid is securely closed before driving away.

To avoid damaging the bottom of the In-Bed Trunk, do not drive over large obstacles, and do not use it as a jacking point to raise the vehicle.

96

In-Bed Trunk Open Indicator

This indicator on the instrument panel reminds you that the In-Bed Trunk is open (see page

69

).

As a safety feature, your vehicle has a release lever on the latch of the In-Bed Trunk lid so it can be opened from the inside. To open the In-Bed Trunk, push the release lever in the direction of the arrow.

Parents should decide if their children should be shown how to use this feature. For more information about child safety, see page

36

Main MenuTable of ContentsstIn-Bed Trunk Main Switch

Washing the In-Bed Trunk

Cargo Hooks

MAIN SWITCH

CARGO HOOKS

In-Bed Trunk

TM

To protect items in the In-Bed Trunk, you can disable its release button by turning off the main switch in the glove box and locking the glove box with the master key.

Even if the main switch is in the OFF position, you can open the In-Bed Trunk with the master key.

DRAIN PLUG

You can wash the inside of the In-Bed Trunk with a water and mild detergent solution, and a soft brush or cloth.

To drain water from the In-Bed Trunk, remove the drain plug by turning it counterclockwise.

When you are finished washing the In-Bed Trunk, dry it with a soft cloth, and reinstall the drain plug.

There are two cargo hooks for plastic grocery bags at the back of the In-Bed Trunk. They are designed to hold light items. Heavy objects may damage the hooks.

97

Main MenuTable of ContentsstSeats

The front passenger’s seat in all models adjusts manually.

−

11 13

Manual Seat Adjustments OnRT,RTX,andCanadianLXmodels Seepages forimportantsafety informationandwarningsabouthowto properlypositiontheseatsandseat- backs. Make all seat adjustments before you start driving.

To adjust the seat forward or backward, pull up on the bar under the seat cushion’s front edge. Move the seat to the desired position, and releasethebar.Trytomovetheseat

98

to make sure it is locked in position.

To change the seat-back angle of the front seat, pull up the lever on the outside of the seat bottom.

Once your seat is adjusted correctly, rock it back and forth to make sure it is locked in position.

Main MenuTable of ContentsstDriver’s Seat Manual Height Adjustment Make all seat adjustments before you start driving.

Make sure to pull the lever upward or downward to its full range.

Driver’s Manual Lumbar Support

Seats

OnRT,RTX,andCanadianLXmodels The height of your driver’s seat is adjustable. To raise the seat, repeatedly pull up the lever on the outside of the seat cushion. To lower the seat, push the lever down repeatedly.

OnRTSmodel Vary the lumbar support by moving the lever on the right side of the seat-back. Move the lever forward or backward to adjust the lumbar support through its full range.

99

Main MenuTable of ContentsstSeats

Power Seat Adjustments OnRTS,RTL,andCanadianEXL models Seepages forimportantsafety informationandwarningsabouthowto properlypositiontheseatsandseat- backs.

11 13

−

The controls for the power adjustable driver’s seat are on the outside edge of the seat bottom. You can adjust the seat with the ignition switch in any position. Make all seat adjustments before you start driving.

Moving the long horizontal switch adjusts the seat bottom in several directions. The seat bottom adjusts in the direction you move the switch. The short vertical switch adjusts the seat-back angle.

100

Moves the seat forward and backward.

Moves the front of the seat up or down.

Raises or lowers the seat.

Moves the whole seat up and forward, or down and backward. The front of the seat also tilts up or down at the same time.

Adjusts the seat-back angle forward or backward.

Increases or decreases the lumbar support. (RTL and Canadian EXL models)

Main MenuTable of ContentsstArmrests

FRONT

REAR

To use the console lid as an armrest, slide it to the desired position.

Make sure your passenger’s hands or fingers are away from the armrest before moving it.

The rear seat armrest is in the center of the rear seats. Pivot it down to use it.

Seats