Each time you press the INFO ( / ▲ ) button, the screen changes as ▼ shown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.
▲ ▼
INFO button SEL/RESET button
CONTINUED
113
2009 Pilot08/03/10 17:43:02 31SZA600 0119
Multi-Information Display
AutoDoorLock There are three settings you can choose from:
SHIFT FROM P The doors lock whenever you move the shift lever out of Park.
−
−
WITH VEH SPD The doors lock when the vehicle speed reaches about 10 mph (about 15 km/h).
−
OFF The auto door lock is deactivated all the time.
114
You can choose this customize item from ‘‘DOOR/WINDOW SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
Press the SEL/RESET button to see the selections.
Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
▲ ▼
2009 Pilot08/03/10 17:43:10 31SZA600 0120
AutoDoorUnlock There are three settings you can choose from:
−
The driver’s door or
SHIFT TO P all the doors, depending on your selection in the next step, unlock when you move the shift lever to Park.
−
The driver’s door or all
IGN OFF the doors, depending on your selection in the next step, unlock when you turn the ignition switch to the LOCK (0) position.
−
OFF deactivated all the time.
The auto door unlock is
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO DOOR LOCK’’ and repeat the procedure again.
Multi-Information Display
You can choose this customize item from ‘‘DOOR/WINDOW SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
CONTINUED
115
2009 Pilot08/03/10 17:43:18 31SZA600 0121
Multi-Information Display
Press the SEL/RESET button to see the selections.
If you choose ‘‘SHIFT TO P’’ or ‘‘IGN OFF’’, you will see the above display.
Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
▲ ▼
▲ ▼
Press the INFO ( / ) button to switch the door lock mode setting between the driver’s door and all doors. Then, press the SEL/RESET button to enter your selection.
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO DOOR UNLOCK’’ and repeat the procedure again.
116
2009 Pilot08/03/10 17:43:27 31SZA600 0122
KeyandRemoteUnlockMode
Multi-Information Display
To select whether the driver’s door unlocks or all the doors unlock when you unlock the doors with the remote transmitter, follow these instructions.
You can choose this customize item from ‘‘DOOR/WINDOW SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
Press the SEL/RESET button to see the selections.
Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
▲ ▼
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘KEY AND REMOTE UNLOCK MODE’’ and repeat the procedure again.
CONTINUED
117
2009 Pilot08/03/10 17:43:33 31SZA600 0123
Multi-Information Display
KeylessLockAcknowledgment When you push the LOCK button on the remote transmitter, some exterior lights flash, and a beeper sounds when you push the LOCK button again within 5 seconds to verify that the doors and the tailgate are locked and the security system has set (see page customize the exterior lights not to flash and the beeper not to sound.
). You can
347
You can choose this customize item from ‘‘DOOR/WINDOW SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
Press the SEL/RESET button to see the selections.
Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.
▲ ▼
118
2009 Pilot08/03/10 17:43:41 31SZA600 0124
SecurityRelockTimer If you unlock the doors and the tailgate with the remote transmitter, but do not open any of the doors or the tailgate within 30 seconds, the doors and the tailgate automatically relock and the security system sets.
You can change this relock time from 30 seconds to 60 or 90 seconds.
Multi-Information Display
You can choose this customize item from ‘‘DOOR/WINDOW SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
CONTINUED
119
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘KEYLESS LOCK ACKNOWLEDGMENT’’ and repeat the procedure again.
2009 Pilot08/03/10 17:43:47 31SZA600 0125
Multi-Information Display
Press the SEL/RESET button to see the selections.
Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
▲ ▼
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘SECURITY RELOCK TIMER’’ and repeat the procedure again.
120
2009 Pilot08/04/14 18:17:56 31SZA600 0126
Controls Near the Steering Wheel
HEADLIGHT/TURN SIGNAL/ FRONT FOG LIGHTS (P.124)
*
VEHICLE STABILITY ASSIST SYSTEM OFF SWITCH
(P.436)
STEERING WHEEL AUDIO CONTROLS * (P.309)
HAZARD WARNING BUTTON
(P.128)
BLUETOOTH HANDSFREELINK SYSTEM VOICE CONTROL BUTTONS * (P.361)
*
(P.390)
(P.169)
PARKING SENSOR SYSTEM SWITCH * DRIVING POSITION MEMORY SYSTEM (P.171) MIRROR CONTROLS POWER DOOR LOCK MASTER SWITCH POWER WINDOW (P.163) SWITCHES FUEL FILL DOOR RELEASE HANDLE GLASS HATCH RELEASE BUTTON/ POWER TAILGATE SWITCH * (P.143)
(P.399)
(P.136)
Vehicle with navigation system is shown.
PARKING BRAKE RELEASE HANDLE (P.167)
HORN *
VOICE CONTROL BUTTONS *
WINDSHIELD WIPERS/ WASHERS (P.122)
PASSENGER AIRBAG OFF INDICATOR (P.34)
(P.422)
VTM-4 LOCK BUTTON * REAR WINDOW DEFOGGER/HEATED MIRROR BUTTON * (P.128, 170) ACCESSORY POWER SOCKET SEAT HEATER SWITCHES * CRUISE CONTROL (P.348) BUTTONS
(P.162)
(P.184)
* * * *
To use the horn, press the center pad of the steering wheel. Only on vehicles equipped with navigation system. Refer to the navigation system manual. If equipped
1 : 2 : 3 : 4 : 4WD models only
121
STEERING WHEEL ADJUSTMENT (P.131)
MULTI-INFORMATION BUTTONS * (P.85)
2009 Pilot08/03/10 17:44:05 31SZA600 0127
Windshield Wipers and Washers
Push the right lever up or down to select a position.
MIST
−
The wipers run at high
speed until you release the lever.
OFF
−
The wipers are not activated.
INT
−
The length of the wipe
interval is varied automatically according to vehicle speed.
If you turn it to the shortest delay, the wipers change to low speed operation when the vehicle speed exceeds 12 mph (20 km/h).
1. 2. 3. 4. 5. 6.
MIST OFF INT LO Low speed HI High speed Windshield washers
Intermittent
− − −
122
LO
−
The wipers run at low speed.
HI
−
The wipers run at high speed.
−
Windshield Washer
Pull the wiper control lever toward you, and hold it. The washers spray until you release the lever. The wipers run at low speed, then complete one more sweep after you release the lever.
2009 Pilot08/03/10 17:44:14 31SZA600 0128
Windshield Wipers and Washers
3.
4.
When you turn the wiper switch to the ‘‘OFF’’ position, the wiper will return to its parked position.
Rotate the switch counterclockwise to spray the window washer.
The rear wiper will not work if the glass hatch is not fully closed.
If you attempt to open the glass hatch while the rear wiper is operating, the wiper will return to the parked position, and then the glass hatch can be opened. After the glass hatch is closed, the rear wiper starts to operate again after a few seconds delay.
When you shift the transmission to the reverse position with the front windshield wipers activated, the rear window wiper operates automatically.
The rear window washer uses the same fluid reservoir as the wind- shield washer.
Rear Window Wiper and Washer
1.
2.
To turn on the rear window wiper, rotate the switch clockwise to ON. It operates intermittently.
Hold past ON to turn the rear window wiper on and to spray the rear window washer.
123
2009 Pilot08/03/10 17:44:21 31SZA600 0129
Turn Signals and Headlights
−
Push down on the Turn Signal lever to signal a left turn and up to signal a right turn. To signal a lane change, push lightly on the lever, and hold it. The lever will return to center when you release it or complete a turn.
−
Turning the ’’ position turns
Headlights On switch to the ‘‘ on the parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights.
Turning the switch to the ‘‘ ’’ position turns on the headlights. If you leave the lights on with the key removed from the ignition switch, you will hear a reminder chime when you open the driver’s door.
1. 2. 3. 4. 5. 6. 7. 8. 9.
Turn signal Off Parking and indicator lights AUTO Headlights on High beams Flash high beams Fog lights off Fog lights on
*
*
*
If equipped
124
When the light switch is in either of these positions, the lights on indicator comes on as a reminder.
This indicator stays on if you leave the lights on and turn the ignition switch to the ACCESSORY (I) or LOCK (0) position.
−
High Beams To switch from low beams to high beams, push the left lever forward until you hear a click. The blue high beam indicator will come on (see page ). Pull it back to return to low beams. To flash the high beams, pull the lever back lightly, then release it. The high beams stay on as long as you hold the lever back.
76
2009 Pilot08/03/10 17:44:28 31SZA600 0130
− The automatic lighting
AUTO feature turns on the headlights and all other exterior lights, when it senses low ambient light.
To turn on automatic lighting, turn the light switch to AUTO at any time. The lights will come on automatically when the outside light level becomes low (at dusk, for example). The lights on indicator comes on as a reminder. The lights and indicator will turn off automatically when the system senses high ambient light.
The lights will remain on when you turn off the ignition switch. They will turn off automatically when you remove the key and open the driver’s door. To turn them on again, either turn the ignition switch to the ON (II) position or turn the light switch to the
position.
Even with the automatic lighting feature turned on, we recommend that you turn on the lights manually when driving at night or in a dense fog, or when you enter dark areas such as long tunnels or parking facilities.
OnTouringmodels
To change the ‘‘AUTO LIGHT
SENSITIVITY’’ setting, see page
111
Do not leave the light switch in AUTO if you will not be driving the vehicle for an extended period (a week or more). You should also turn off the lights if you plan to leave the engine idling or off for a long time.
Headlights
LIGHT SENSOR
The automatic lighting feature is controlled by a sensor located on top of the dashboard. Do not cover this sensor or spill liquids on it.
125
2009 Pilot08/03/10 17:44:35 31SZA600 0131
Headlights
Fog Lights ExceptLXmodels Turn the fog lights on and off by turning the switch next to the headlight switch.
You can use the fog lights only when the headlights are on low beam. With the light switch in the AUTO position, you can also use the fog lights when the headlights turn on automatically. They will go off when the headlights turn off.
Daytime Running Lights With the headlight switch off, the daytime running lights come on when you turn the ignition switch to the ON (II) position and release the parking brake. They remain on until you turn the ignition switch off, even if you set the parking brake.
When the headlights are on, the daytime running lights are off.
OnTouringmodels If you see a ‘‘CHECK DRL SYSTEM’’ message on the multi- information display, there is a problem with the daytime running light system. Take your vehicle to a dealer to have it checked.
When the multi-information display shows a ‘‘DRL OFF’’ message, the daytime running lights are off. Follow the procedure in the left column to turn them on.
126
2009 Pilot08/03/10 17:44:42 31SZA600 0132
Headlights
Automatic Lighting Off Feature
This feature turns off the headlights,
all other exterior lights, and the
instrument panel lights within 15
seconds after you remove the key
and close the driver’s door.
OnTouringmodels To change the ‘‘HEADLIGHT AUTO OFF TIMER’’ setting, see page
110
If you turn the ignition switch to the LOCK (0) position with the headlight switch on, but do not open the door and get out, the lights turn off after 10 minutes (3 minutes, if the switch is in the ‘‘AUTO’’ position).
The lights turn on again when you unlock or open the driver’s door. If you unlock the door, but do not open it within 15 seconds, the lights go off. With the driver’s door open, you will hear a lights-on reminder chime.
The automatic lighting off feature activates if you leave the headlight switch in the ‘‘ position or if the lights are turned on by setting the switch in the ‘‘AUTO’’ position, and you remove the key, then open and close the driver’s door.
’’ or ‘‘
’’
127
2009 Pilot08/03/10 17:44:49 31SZA600 0133
Hazard Warning Button, Rear Window Defogger
Hazard Warning Button
Rear Window Defogger
Make sure the rear window is clear and you have good visibility before starting to drive.
The defogger wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side-to-side.
ExceptU.S.LXmodel Pushing this button also turns the mirror heaters on or off. For more information, see page
170
Push the button to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both turn indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.
The rear window defogger will clear fog, frost, and thin ice from the window. Push the defogger button to turn it on and off. The indicator in the button lights to show the defogger is on. If you do not turn it off, the defogger will shut itself off after about 15 minutes. It also shuts off when you turn off the ignition. You have to turn it on again when you restart the vehicle.
128
2009 Pilot08/03/10 17:44:56 31SZA600 0134
Separate adjustments can be made when the headlights are on and off.
You will hear a beep when maximum or minimum brightness is reached. You will also hear a beep when the maximum level is canceled by turning the knob a click to the left.
To reduce glare at night, the instrument panel illumination dims when you turn the light switch to
or
. Turning the select/
reset knob to the right until you hear a beep will cancel the reduced brightness.
The select/reset knob on the instrument panel controls the brightness of the instrument panel lights. Turn the knob to adjust the brightness.
Instrument Panel Brightness
U.S. model is shown.
ExceptTouringmodels The level of brightness is shown on the information display while you adjust it. It goes out about 5 seconds after you finish adjusting.
CONTINUED
129
2009 Pilot08/03/10 17:45:00 31SZA600 0135
Instrument Panel Brightness
OnTouringmodels The level of brightness is shown on the multi-information display while you adjust it. It goes out 5 seconds after you finish adjusting.
When the brightness reaches the maximum level, ‘‘BRIGHTNESS MAXIMUM LEVEL’’ appears on the display.
130
2009 Pilot08/03/10 17:45:07 31SZA600 0136
Make any steering wheel adjustment before you start driving.
Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.
Adjust the steering wheel only when the vehicle is stopped.
1.
Push the lever under the steering column all the way down.
2.
Move the steering wheel up or down, and in or out, so it points toward your chest, not toward your face. Make sure you can see the instrument panel gauges and indicators.
Steering Wheel Adjustment
3.
Push the lever up to lock the steering wheel in position.
4.
Make sure you have securely locked the steering wheel in place by trying to move it up, down, in, and out.
131
2009 Pilot08/03/10 17:45:14 31SZA600 0137
Keys and Locks
KEY NUMBER TAG
MASTER KEY WITH REMOTE TRANSMITTER
VALET KEY (Light Gray)
You should have received a key number tag with your keys. You will need this key number if you ever have to get a lost key replaced. Use only Honda-approved key blanks.
These keys contain electronic circuits that are activated by the immobilizer system. They will not work to start the engine if the circuits are damaged.
Protect the keys from direct sunlight, high temperature, and high humidity.
Do not drop the keys or set heavy objects on them.
Keep the keys away from liquids. If they get wet, dry them immediately with a soft cloth.
The valet key does not contain a battery. Do not try to take it apart.
The master key fits all the locks on your vehicle. The valet key works only in the ignition and the driver’s door lock. You can keep the glove box locked when you leave your vehicle and the valet key at a parking facility.
132
2009 Pilot08/03/10 17:45:19 31SZA600 0138
The Immobilizer System protects your vehicle from theft. If an improperly-coded key (or other device) is used, the engine’s fuel system is disabled.
The system may not recognize your key’s coding if another immobilizer key or other metal object (i.e. key fob) is near the ignition switch when you insert the key.
If the system repeatedly does not recognize the coding of your key, contact your dealer.
When you turn the ignition switch to the ON (II) position, the immobilizer system indicator should come on briefly, then go off. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to the LOCK (0) position, remove the key, reinsert it, and turn the ignition switch to the ON (II) position again.
Immobilizer System
Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle undrivable.
If you have lost your key and you cannot start the engine, contact your dealer.
133
2009 Pilot08/03/10 17:45:24 31SZA600 0139
Immobilizer System
Always take the ignition key with you whenever you leave the vehicle alone.
ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.
AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.
Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.
134
2009 Pilot08/03/10 17:45:32 31SZA600 0140
If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key.
−
You can
ACCESSORY (I) operate the audio system and the accessory power sockets in this position.
The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), and START (III).
−
You can insert or
LOCK (0) remove the key only in this position. To turn the key to the LOCK (0) position, the shift lever must be in Park, and you must push the key in slightly.
−
This is the normal key
ON (II) position when driving. Several of the indicators on the instrument panel come on as a test when you turn the ignition switch from the ACCESSORY (I) to the ON (II) position.
−
Use this position
START (III) only to start the engine. The switch returns to the ON (II) position when you let go of the key.
Ignition Switch
You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or the ACCESSORY (I) position and open the driver’s door. Remove the key to turn off the beeper.
OnTouringmodels You will also see a ‘‘REMOVE KEY’’ message on the multi-information display (see page
94
).
The shift lever must be in Park before you can remove the key from the ignition switch.
135
2009 Pilot08/03/10 17:45:41 31SZA600 0141
Door Locks
Unlock
Lock
Lock
Unlock
To lock all doors and the tailgate, push the top of the master door lock switch on either front door, pull the lock tab rearward on the driver’s door, or use the key on the outside lock on the driver’s door.
Pushing the bottom of the either master door lock switch will unlock all doors and the tailgate. Pushing forward the lock tab on the driver’s doors unlocks only that door.
The lock tab on any passenger’s door locks and unlocks that door.
All doors and the tailgate can be locked from the outside by using the key in the driver’s door lock. To unlock only the driver’s door, insert the key, turn the key, and release it. The remaining doors and the tailgate unlock when you turn the key a second time within a few seconds.
136
OnTouringmodels
To change the ‘‘KEY AND REMOTE
UNLOCK MODE’’ setting, see page
117
When the vehicle speed reaches about 10 mph (15 km/h) or more, all the doors lock automatically.
To change the ‘‘AUTO DOOR
LOCK’’ setting, see page
114
When you shift to P after driving, the driver’s door unlocks.
To change the ‘‘AUTO DOOR UNLOCK’’ setting, see page
115
2009 Pilot08/03/10 17:45:53 31SZA600 0142
Auto Door Locking ExceptTouringmodels The auto door locking feature has three possible settings:
The auto door locking is deactivated all the time.
The doors and the tailgate lock whenever you move the shift lever out of the Park (P) position.
The doors and the tailgate lock when the vehicle speed reaches 9 mph (15 km/h). This is the default setting.
Auto Door Locking/Unlocking ExceptTouringmodels Your vehicle has customizable settings for the doors and tailgate to automatically lock and unlock. There are default settings for each of these features. You can turn off or change the settings for these features as described on the following pages.
When you customize the setting, make sure your vehicle is parked safely, the engine is off, and apply the parking brake. Make all settings before you start driving.
OnTouringmodels
To change the ‘‘AUTO DOOR
LOCK’’ setting, see page
114
To change the ‘‘AUTO DOOR UNLOCK’’ setting, see page
115
Door Locks
ToturnofftheAutoDoorLock modes:
1.
Make sure the shift lever is in the Park (P) position.
2.
Turn the ignition switch to the ON (II) position, and open the driver’s door.
CONTINUED
137
2009 Pilot08/03/10 17:46:02 31SZA600 0143
Door Locks
3.
Push and hold the front of the master door lock switch on the driver’s door until you hear a click (after about 5 seconds).
ToprogramtheParkLockmode: Locksalldoorsandtailgatewhenthe shiftleverismovedoutofthePark(P) position.
4.
Release the switch, and within 5
seconds, turn the ignition switch
to the LOCK (0) position.
3.
Push and hold the front of the
master door lock switch on the
driver’s door. You will hear a click.
Keep holding the switch until you
hear another click (after about 5
seconds).
4.
Release the switch, and within 5
seconds, turn the ignition switch
to the LOCK (0) position.
1.
Make sure the shift lever is in the Park (P) position.
2.
Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.
138
2009 Pilot08/03/10 17:46:14 31SZA600 0144
ToprogramtheDriveLockmode: Locksalldoorsandtailgatewhenthe vehicle’sspeedreachesabout9mph (15km/h).
3.
4.
Push and hold the brake pedal, and move the shift lever out of the Park (P) position.
Push and hold the front of the
master door lock switch on the
driver’s door. You will hear a click.
Keep holding the switch until you
hear another click (after about 5
seconds).
5.
Release the switch and, within 5
seconds, turn the ignition switch
to the ACCESSORY (I) position.
Move the shift lever to the Park
(P) position.
1.
Make sure the shift lever is in the Park (P) position.
6.
Turn the ignition switch to the LOCK (0) position.
2.
Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.
Door Locks
Auto Door Unlocking ExceptTouringmodels The auto door unlocking feature has five possible settings:
The auto door unlocking is deactivated all the time.
The driver’s door unlocks when you move the shift lever to the Park (P) position. This is the default setting.
All doors and tailgate unlock when you move the shift lever to the Park (P) position.
The driver’s door unlocks whenever you turn the ignition switch to the ACCESSORY (I) position.
All doors and tailgate unlock whenever you turn the ignition switch to the ACCESSORY (I) position.
CONTINUED
139
2009 Pilot08/03/10 17:46:24 31SZA600 0145
Door Locks
ToturnofftheAutoDoorUnlock modes:
1.
Make sure the shift lever is in the Park (P) position.
2.
Turn the ignition switch to the ON (II) position, and open the driver’s door.
140
3.
Push and hold the rear of the master door lock switch on the driver’s door. You will hear a click, and after about 5 seconds, you will hear another click.
4.
Release the switch, and within 5
seconds, turn the ignition switch
to the LOCK (0) position.
ToprogramtheParkUnlockmode: Unlocksthedriver’sdoororalldoors andtailgatewhentheshiftleveris movedintothePark(P)position.
1.
Make sure the shift lever is in the Park (P) position.
2.
Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.
2009 Pilot08/03/10 17:46:35 31SZA600 0146
3.
Push and hold the rear of the master door lock switch on the driver’s door. You will hear a click. Continue to hold down the switch:
Until you hear another click (after about 5 seconds) to activate driver’sdoorunlock feature.
Or, until you hear two more clicks (after about 10 seconds) to activate alldoorsandtailgate unlockfeature
4.
Release the switch, and within 5
seconds, turn the ignition switch
to the LOCK (0) position.
ToprogramtheIgnitionSwitch Unlockmode: Unlocksthedriver’sdoororalldoors andtailgatewhentheignitionswitchis movedoutoftheON(II)position.
1.
Make sure the shift lever is in the Park (P) position.
2.
Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.
Door Locks
3.
Push and hold the brake pedal, and move the shift lever out of P.
4.
Push and hold the rear of the master door lock switch on the driver’s door. You will hear a click. Continue to hold the switch:
Until you hear another click (after about 5 seconds) to activate the driver’s door unlock feature.
Or, until you hear two more clicks (after about 10 seconds) to activate all doors and tailgate unlock feature.
5.
Release the switch and, within 5
seconds, turn the ignition switch
to the ACCESSORY (I) position.
Move the shift lever to the Park
(P) position.
6.
Turn the ignition switch to the LOCK (0) position.
141
2009 Pilot08/03/10 17:46:42 31SZA600 0147
Door Locks, Tailgate and Glass Hatch
Childproof Door Locks
Tailgate
LockoutPrevention With any door and the tailgate open and the key in the ignition, both master door lock switches are disabled. They are not disabled if all the doors and the tailgate are closed. If you try to lock an open driver’s door by pulling the lock tab rearward the lock tab on the driver’s door pops out.
Lock
The childproof door locks are designed to prevent children seated in the rear from accidentally opening the rear doors. Each rear door has a lock lever near the edge. With the lever in the LOCK position (lever is down), the door cannot be opened from the inside regardless of the position of the lock tab. To open the door, push the lock tab forward and use the outside door handle.
Make sure the shift lever is in the Park (P) position.
To open the tailgate, press and hold the switch, then lift up. To close the tailgate, use the inner handle to pull it down, then press down on the back edge.
142
2009 Pilot08/03/10 17:46:49 31SZA600 0148
Keep the tailgate closed at all times
while driving to avoid damaging the
tailgate and to prevent exhaust gas
from getting into the interior. See
Carbon Monoxide Hazard
59
on page
Power Tailgate OnTouringmodels
POWER TAILGATE SWITCH
The tailgate can be opened and closed with the remote transmitter (see page ) or the switch in the driver’s door pocket when both front doors are unlocked.
149
Tailgate and Glass Hatch
If the glass hatch is opened, remote transmitter operation is canceled until it is closed.
Press and hold the tailgate button on the remote transmitter or the switch for about 1 second to open or close the tailgate. Each time you press the button on the remote transmitter or the switch, you will hear a beep, and some front and rear lights will flash.
If you push the same button or switch again while the tailgate is opening or closing, you will hear three beeps, and the tailgate will stop moving, reverse direction, and stop at the fully opened or closed position.
CONTINUED
143
2009 Pilot08/03/10 17:46:58 31SZA600 0149
Tailgate and Glass Hatch
Auto-Reverse The power tailgate has an auto- reverse feature. If it meets resistance while opening or closing, it will beep three times and reverse direction. However, the tailgate may not reverse immediately. Always make sure passengers and objects are clear of the tailgate before opening or closing it.
TAILGATE SWITCH
The tailgate can also be closed by pressing the button on the tailgate. If you press the button again while the tailgate is closing, you will hear three beeps, and the tailgate will stop moving, reverse direction, and stop at the fully opened position.
Closing a power tailgate while anyone is in the path of the tailgate can cause serious injury.
Make sure everyone is clear before closing the power tailgate.
144
Also check that passengers, especially children, do not have their hands on the edge of the tailgate or on the tailgate sill. The auto reverse feature stops working when the tailgate is about to latch so the motor can pull the tailgate shut.
If your vehicle’s battery is disconnected, goes dead, or the fuse is removed while the tailgate is fully open, the power tailgate needs to be reset. After connecting the battery or installing the fuse, close the tailgate fully by hand.
The power tailgate may not open or close under the these conditions:
The vehicle is parked on a steep hill.
When the vehicle is swayed in a strong wind.
2009 Pilot08/03/10 17:47:08 31SZA600 0150
When the tailgate or the roof is covered with snow or ice.
Do not install any accessories on the tailgate. It may cause the tailgate not to function properly. If there is snow or ice on the tailgate, make sure to remove it before you operate the tailgate.
If you push the tailgate release button inside the handle while the tailgate is opening or closing, it will stop moving. You need to open or close it the rest of the way manually.
The tailgate has sensors on both sides. Be careful not to damage them. If the sensors are damaged, the power tailgate does not function properly.
Tailgate and Glass Hatch
Unlocking the Tailgate
If you try to drive off with the tailgate not closed completely, a beeper sounds and a ‘‘DOOR & TAILGATE OPEN’’ message is shown on the multi-information display.
Keep the tailgate closed at all times
while driving to avoid damaging the
tailgate and to prevent exhaust gas
from getting into the interior. See
Carbon Monoxide Hazard
59
on page
If there is a problem in the power tailgate system, you will see a ‘‘CHECK POWER TAILGATE’’ message on the multi-information display. Have the system checked by your dealer.
With this message shown on the multi-information display, you can still open or close the tailgate manually.
If the power door lock system cannot unlock the tailgate, unlock it manually.
Use a small flat-tipped screwdriver to remove the cover on the back of the tailgate.
CONTINUED
145
2009 Pilot08/03/10 17:47:17 31SZA600 0151
Tailgate and Glass Hatch
OnTouringmodels
ExceptTouringmodels
Glass Hatch
GLASS HATCH RELEASE BUTTON
If you cannot open the tailgate, remove the cover on the back of the tailgate (see page ). Make sure the shift lever is in the Park (P) position. Push the release lever to the right as shown, then pull the outer handle to open the tailgate.
145
To open the glass hatch, press the glass hatch release button on the tailgate.
To close the glass hatch, lower it and press on the handle until it latches.
Make sure the shift lever is in the Park (P) position.
Push the release lever to the right as shown.
If you need to unlock the tailgate manually, it means there is a problem with the tailgate. Have the vehicle checked by your dealer.
146
2009 Pilot08/03/10 17:47:22 31SZA600 0152
The rear wiper will not operate with the glass hatch open. If you open the glass hatch while the rear wiper is operating, the wiper will return to its parked position (see page ). The wiper will resume operation after the glass hatch is closed.
123
ExceptTouringmodels
Tailgate and Glass Hatch
Keep the tailgate and the glass hatch
closed at all times while driving to
avoid damaging the tailgate and the
glass hatch, and to prevent exhaust
gas from getting into the interior.
Carbon Monoxide Hazard
See
page
59
on
GLASS HATCH RELEASE BUTTON
You can also open the glass hatch by pressing the glass hatch release button on the driver’s door or on the remote transmitter.
147
2009 Pilot08/03/10 17:47:30 31SZA600 0153
Remote Transmitter
Remote Transmitter
Except Touring models
On Touring models
UNLOCK BUTTON
UNLOCK BUTTON
LOCK BUTTON
GLASS HATCH RELEASE BUTTON
PANIC BUTTON
LOCK BUTTON
TAILGATE BUTTON
PANIC BUTTON
OnTouringmodels To change the ‘‘KEYLESS LOCK ACKNOWLEDGEMENT’’ setting, see page
118
−
LOCK Press this button once to lock all doors and the tailgate. Some exterior lights will flash. When you push LOCK twice within 5 seconds, you will hear a beep to verify that the doors and tailgate are locked and the security system has set. This button does not work if any door or tailgate is not fully closed.
148
−
Press this button once
UNLOCK to unlock the driver’s door. Push it twice to unlock the other doors. Some exterior lights will flash twice when you push the button. If you do not open any door or the tailgate within 30 seconds, they will automatically relock.
OnTouringmodels
To change the ‘‘KEY AND REMOTE
UNLOCK MODE’’ setting, see page
117
To change the ‘‘SECURITY
RELOCK TIMER’’ setting, see page
119
2009 Pilot08/03/10 17:47:38 31SZA600 0154
Remote Transmitter
−
OnTouringmodels TAILGATE Press and hold the TAILGATE button to open or close the power tailgate. When the tailgate begins to move, you will hear a beep, and some front and rear lights will flash.
If you push the same button again while the tailgate is opening or closing, three beeps sound, the tailgate stops moving, reverses direction and stops in the fully opened or fully closed position.
When you press the UNLOCK
button, the front and rear individual
map lights and the cargo area light,
depending on their switch positions,
will come on (see page
). If you
do not open any door or the tailgate,
the lights stay on for about 30
seconds, then go out. If you relock
the doors and the tailgate with the
remote transmitter before 30
seconds have elapsed, the lights will
go off immediately.
174
ExceptTouringmodels GLASS HATCH RELEASE Press this button for about 1 second to open the glass hatch. Even if the glass hatch is open, the tailgate can be locked with the remote transmitter.
−
−
Press and hold this
PANIC button for about 1 second to attract attention; the horn will sound, and the exterior lights will flash for about 30 seconds. To cancel panic mode, press any other button on the remote transmitter, or turn the ignition switch to the ON (II) position. Panic mode does not work when the key is in the ignition switch.
RemoteTransmitterCare
Avoid dropping or throwing the transmitter. Protect the transmitter from extreme temperature. Do not immerse the transmitter in any liquid. If you lose a transmitter, the replacement needs to be reprogrammed by your dealer.
149
2009 Pilot08/03/10 17:47:47 31SZA600 0155
Remote Transmitter
Replacing the Transmitter Battery If it takes several pushes on the button to lock or unlock the doors and the tailgate, replace the battery as soon as possible.
Battery type: CR1616
BATTERY