1995 Honda Odyssey Owners Manual

Main MenuTable of ContentsstIf a toddler seat is used in the front passenger's seat, the vehicle seat should be moved as far back as possible. If the passenger's bag inflates, it could seriously hurt a toddler who is not in the proper position or properly restrained.

We also recommend that any child who is too large to use an infant or toddler seat ride in the second or third seat and wear a lap/shoulder belt properly for protection. If the child is not large enough to wear the lap/shoulder belt properly, you should use a booster seat.

Important Safety Reminders Never hold a baby or child on your lap when riding in a car. If you are wearing your seat belt, the violent forces created during a crash will tear the child from your arms. The child could be seriously hurt or killed.

If you are holding a child and not wearing a seat belt in a crash, you could crush the child against the car's interior.

Never put your seat belt over yourself and a child. During a crash, the belt could press deep into the child, causing serious internal injuries.

Child Safety

Two children should never use the same seat belt. If they do, they could be very seriously injured in a crash.

If you are driving with small children in the car, you should use the childproof door locks to prevent them from opening the rear doors (see page 54).

For their safety, do not leave children alone in your car without adult supervision.

Driver and Passenger Safety

Main MenuTable of ContentsstChild Safety

General Guidelines for Restraining Children Under 18
kg (40 lbs) Use an approved child seat. The seat must meet Federal Motor Vehicle Safety Standard 213 (FMVSS-213) or Canadian Motor Vehicle Safety Standards. Look for the manufac- turer's statement of compliance on the box and seat.

Use a seat of the right size. Make sure the seat fits your child. Check the seat manufacturer's instructions and labels for height and weight limits.

Secure the child seat to the car. All approved child seats are designed to be secured to the car seat by the lap belt or the lap belt portion of a lap/ shoulder belt. A child whose seat is not properly secured to the car can be endangered in a crash.

Driver and Passenger Safety

Restraining an Infant Who Weighs Less Than 9 kg (20 Ibs)

To properly route a seat belt through a child seat, follow the seat maker's instructions. If you use a lap/shoulder belt, follow the instructions on page 25.

Secure the child in the child seat. Make sure the infant or child is firmly secured to the child seat. Use the straps provided, and carefully follow the manufacturer's instructions.

An infant up to about 9 kg (20 Ibs) must be restrained in an infant seat or a convertible seat designed for a baby. Because infants must ride in a reclining position, be sure the infant seat always faces the REAR of the car as shown.

Main MenuTable of ContentsstWe recommend that you place your child's infant seat in the second seat and secure it with the vehicle's lap/ shoulder belt or lap belt (seven- passenger model). If you use the lap/shoulder belt, be sure to follow the instructions on page 25.

We strongly recommend that you do not put an infant seat in the front passenger's seat. If the airbag inflates, it can hit the infant seat with great force. The infant seat can be dislodged or struck with enough force to cause very serious injury to the infant.

Restraining a Child Who Weighs Between 9 and 18 kg (20 and 40
Ibs)

Child Safety

We recommend that you place your child's toddler seat in the second seat and secure it with the vehicle's lap/shoulder belt or lap belt (seven- passenger model). If you use the lap/shoulder belt, be sure to follow the instructions on page 25.

Toddler seats are designed for children who weigh between 9 and 18 kg (20 and 40 Ibs).

CONTINUED

Driver and Passenger Safety

Main MenuTable of ContentsstChild Safety

If you are using a toddler seat in the front passenger's seat, move the passenger's seat as far back as possible before installing the child seat. If the passenger's bag inflates, it could seriously hurt a toddler who is not in the proper position or properly restrained.

Restraining a Child Who Weighs Over 18 kg (40 Ibs)

We recommend that, whenever possible, a child who has outgrown a toddler seat ride in the second or third seat and use a lap/shoulder belt.

Put the seat belt on your child and check its fit. The shoulder belt should fit over the collarbone and across the chest. The lap belt should sit low on your child's hips, not across the stomach.

If the shoulder belt crosses the neck while sitting in the second or third bench seat, have your child move toward the center of the seat until the belt fits properly. If the belt still crosses the child's neck, you should use a booster seat.

Several styles of booster seats are available. We recommend a design that allows the child to use the car's lap/shoulder belt.

Whichever style you select, follow the booster seat manufacturer's instructions.

Driver and Passenger Safety

Main MenuTable of ContentsstSecuring a Child Seat with a Lap/ Shoulder Belt The lap/shoulder belt retractors in the passenger seating positions have a built-in locking mechanism intended to secure a child seat. If you are placing a child seat in one of the outside seating positions, do the following:

Child Safety

1. Place the child restraint in the

desired seating position. Route the lap/shoulder belt through the seat according to the seat manufac- turer's instructions.

6. Push and pull on the child seat to

verify that it is held firmly in place. If not, unlatch the seat belt, allow it to retract fully, and repeat these steps.

To unlatch the seat belt, push the red PRESS button on the buckle. Guide the belt across to the door pillar. If the belt doesn't retract easily, pull it out and check for twists or kinks.

2. Insert the latch plate into the buckle. Make sure it is fully latched.

3. Slowly pull the shoulder portion of the belt out of the retractor until it stops.

4. Allow the belt to slowly feed back into the retractor. You should hear a clicking noise that indicates the locking mechanism has engaged.

5. After the belt has retracted fully, pull up on the shoulder portion to remove any slack.

Driver and Passenger Safety

Main MenuTable of ContentsstInstall the tether hardware that came with the child seat. Tighten to: 22 N.m (2.2 kg-m, 16 Ib-ft)

If you are not sure how to install the bracket, have it installed by your Honda dealer.

If you need an anchor plate and mounting hardware, you can obtain them by writing to:

American Honda Motor Co., Inc. Consumer Affairs 1919 Torrance Blvd. Torrance, CA 90501-2746

Canadian Models

Your Honda has attachment points for a tether-style child seat to be installed on the second or third seat as shown.

Child Safety

Using Child Restraints with Tethers U.S. Models

Your Honda has two attachment points on the tailgate sill that allow for a tether-style child seat to be installed in the third row seat.

Select the attachment point you want to use and remove the plug with a small flat-tipped screwdriver or fingernail file.

Driver and Passenger Safety

Main MenuTable of ContentsstSecond Seat Installation: There are three attachment points available for the seven-passenger model, and two attachment points available for the six-passenger model.

To install a child seat in the second seat, fold the third seat into the floor recess (see page 62). You will find a U-shaped slit in the carpeting at each attachment point. Select the attach- ment point you want to use, and pull up the carpeting at the slit.

Child Safety

Third Seat Installation: There are two attachment points on the tailgate sill. Select the attach- ment point you want use, and remove the plug with a small flat- tipped screwdriver or a fingernail file.

Storing a Child Seat When you are not using an infant seat or other child restraint, either remove it or make sure it is properly secured so it cannot be thrown around the car during a crash.

Install the tether hardware that came with the child seat. Tighten to: 22 N.m (2.2 kg-m, 16 Ib-ft)

If you are not sure how to install the bracket, have it installed by your Honda dealer.

Driver and Passenger Safety

Main MenuTable of ContentsstThe safest thing you can do is never drink and drive. This can be done if you plan ahead. If you know you are going to be drinking, make plans to ride with a friend who will not be drinking.

If you have no choice but to drive, stop drinking and give yourself lots of time to sober up. Time is the only thing that can make you sober. Things like coffee or a cold shower don't speed up the process.

What if you find that you've been drinking and cannot get a ride from a friend? Find alternative transpor- tation. Call a taxi. Take a bus. Many communities have transportation services devoted to shuttling people who have been drinking.

If you see friends trying to get behind the wheel after drinking, stop them. Drive them yourself or arrange other transportation. If you think you are interfering, remember that your interference will keep them from sharing the road with you.

Alcohol and Drugs

Driving a car requires your full at- tention and alertness. Traffic condi- tions change rapidly. You must be able to react just as rapidly. Alcohol or drugs directly affect your alert- ness and ability to react. Even pre- scription and non-prescription medi- cines can have this effect.

There are laws that deal with drunken driving. These laws define how much alcohol it takes in your system to be legally "drunk." How- ever, your judgment and reaction time get worse with every drink — even the first one.

Driver and Passenger Safety

Main MenuTable of ContentsstYour car's exhaust contains carbon monoxide gas. You should have no problem with carbon monoxide entering the car in normal driving if you maintain your car properly. Have the exhaust system inspected for leaks whenever:

High levels of carbon monoxide can collect rapidly in enclosed areas, such as a garage. Do not run the engine with the garage door closed. Even with the door open, run the engine only long enough to move the car out of the garage.

The car is raised for an oil change. You notice a change in the sound of the exhaust. The car was in an accident that may have damaged the underside.

With the tailgate open, air flow can pull exhaust gas into your car's interior and create a hazardous condition. If you must drive with the tailgate open, open all the windows and set the heating and cooling system as follows.

Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and can even kill you.

Avoid any enclosed areas or activities that expose you to carbon monoxide.

Carbon Monoxide Hazard

If you must sit in your parked car, even in an unconfined area, with the engine running, adjust the heating and cooling system as follows:

1. Push the 2. Select the 3. Turn the fan on high speed. 4. Set the temperature control to a

button. mode.

comfortable setting.

Driver and Passenger Safety

Main MenuTable of ContentsstReporting Safety Defects (U.S. Cars)

If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying American Honda Motor Co., Inc.

If NHTSA receives similar com- plaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or American Honda Motor Co., Inc.

To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424-9393 (or 366-0123 in Washington D.C. area) or write to: NHTSA, U.S. Department of Transportation, Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from the Hotline.

Driver and Passenger Safety

Main MenuTable of ContentsstThese labels are in the locations shown. They warn you of potential hazards that could cause serious injury. Read these labels carefully and don't remove them.

If a label comes off or becomes hard to read, contact your Honda dealer for a replacement.

BATTERY

Safety Labels

RADIATOR CAP

Driver and Passenger Safety

Main MenuTable of ContentsstInstruments and Controls

This section gives information about the controls and displays that contribute to the daily operation of your Honda. All the essential controls are within easy reach.

Control Locations............................ 34
Indicator Lights................................ 35
Gauges............................................. 39
Speedometer............................... 39
Trip Meter................................... 39
Odometer..................................... 39
Temperature Gauge................... 40
Fuel Gauge.................................. 40
Maintenance Required

Indicator................................... 40

Controls Near the Steering

Wheel...................................... 41
Headlights................................... 42
Daytime Running Lights............ 42
Instrument Panel Brightness.... 43

Turn Signals................................. 43
Windshield Wipers...................... 44
Windshield Washers................... 44
Rear Window Wiper and

Washer...................................... 45
Hazard Warning.......................... 45
Rear Window Defogger.............. 45
Steering Wheel Adjustment....... 46
Steering Wheel Controls ................ 48
Cruise Control.............................. 48
Horn............................................. 51
Keys and Locks................................ 51
Keys............................................... 51
Ignition Switch............................. 52
Power Door Locks....................... 53
Remote Transmitter.................... 54
Childproof Door Locks............... 54
Tailgate......................................... 55
Glove Box..................................... 55
Seats................................................. 56
Passenger Seating...................... 56
Seat Adjustments........................ 56
Driver's Seat Power Height

Adjustment.............................. 57
Head Restraints.......................... 58
Third Seat Access....................... 58

Removing the Second Seats

in the Six-Passenger Model.... 59

Folding the Second Seats in the Seven-Passenger

Model................................... 60
Reclining the Second Seat.......... 61
Folding the Third Seat

in All Models........................... 62
Power Windows............................... 64
Sunroof............................................. 65
Mirrors............................................. 66
Adjusting the Power Mirrors..... 67
Parking Brake................................. 68
Digital Clock..................................... 68
Beverage Holder.............................. 69
Dashboard Compartment............... 70
Center Poket.................................... 71
Coin Box........................................... 71
Vanity Mirror................................... 71
Cigarette Lighter............................. 72
Ashtrays........................................... 72
Interior Lights.................................. 73
Ceiling Lights.............................. 73
Spotlights..................................... 73
Tailgate Light............................... 74
Courtesy Lights........................... 74

Instruments and Controls

Main MenustControl Locations

DOOR LOCK SWITCH (P.53)

POWER WINDOW SWITCH (P.64)

FUEL FILL DOOR RELEASE (P.110)

MIRROR CONTROLS (P.67)

DIGITAL CLOCK (P.68)

HEATING/COOLING CONTROL (P.78)

AUDIO SYSTEM (P.84)

Instruments and Controls

HOOD RELEASE HANDLE (P.111)

Main MenuTable of ContentsstThe instrument panel has many indicators to give you important information about your car.

Lamp Check Many of the indicator lights come on when you turn the ignition switch ON (II), allowing you to see that they are working. The instrument panel should look like the illustration. If an indicator does not light during this test, it cannot alert you if that system develops a problem. Have the dealer check your car for burned-out bulbs or other problems.

* The U.S. instrument panel is shown. Differences for the Canadian model are noted in the text.

Indicator Lights

MALFUNCTION INDICATOR LAMP/ CHECK ENGINE LIGHT*

PARKING BRAKE AND BRAKE SYSTEM INDICATOR*

DOOR AND BRAKE LAMP MONITOR

HIGH BEAM INDICATOR

CRUISE CONTROL INDICATOR

LOW FUEL INDICATOR

LOW OIL PRESSURE INDICATOR

SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR

ANTI-LOCK BRAKE SYSTEM INDICATOR*

CHARGING SYSTEM INDICATOR

SEAT BELT REMINDER LIGHT

Instruments and Controls

Main MenuTable of ContentsstIndicator Lights

Seat Belt Reminder Light

This indicator lights when you turn the ignition ON (II). It is a reminder to you and your passengers to protect yourselves by fastening the seat belts. A beeper also sounds if you have not fastened your seat belt.

If you do not fasten your seat belt, the beeper will stop after a few seconds but the light stays on until you do. Both the light and the beeper stay off if you fasten your seat belt before turning on the ignition.

Instruments and Controls

Low Oil Pressure Indicator

This indicator lights when the oil pressure in the engine drops low enough to cause damage. It should light when the ignition is ON (II) and go out after the engine starts. If this light flashes or stays on when the engine is running, there is a possi- bility of serious engine damage. Safely pull to the side of the road and shut off the engine as soon as you can. Turn to page 204 for in- structions and precautions on checking the engine.

Charging System Indicator

This light indicates the battery is not being charged. It should come on when the ignition is ON (II), and go out after the engine starts. If this light comes on while driving, the battery is not being charged. Turn to page 205 for information about what to do.

US

Canada

BRAKE

Parking Brake and Brake System Indicator This light has two functions:

1. It lights as a reminder that you

have set the parking brake. Driving with the parking brake set can damage the brakes and tires, and cause the Anti-lock brake system to turn off (see page 125).

2. It can indicate the brake fluid level

is low if it remains lit after you release the parking brake or comes on while driving. This is normally due to worn brake pads. Have your dealer check the braking system for worn pads or fluid leaks.

Main MenuTable of ContentsstSupplemental Restraint System Indicator

SRS The SRS light normally comes on for a few seconds when you turn the ignition ON (II). If it doesn't, or it stays on after the engine starts, something is wrong with the Supplemental Restraint System. It may also flash on and off to indicate a problem. If you see any of these indications, the airbag may not work when needed in an accident. Take the car to your dealer promptly for diagnosis and service.

US ABS Canada

Anti-lock Brake System (ABS) Indicator

Only on cars equipped with ABS (see page 125) This light normally comes on when you turn the ignition ON (II) and

goes off after the engine starts. If if comes on at any other time, there is a problem in the ABS. If this happens, fake the car to your dealer to have it checked. With the light on, your car still has normal braking ability but no anti-lock.

US

Canada

Malfunction Indicator Lamp

Check Engine Light

This light comes on for a few seconds when you turn the ignition switch ON (II). If it comes on at any other time, it indicates one of the engine's emission control systems may have a problem. Turn to page 206 for information about what to do.

Indicator Lights

Door and Brake Lamp Monitor

The appropriate light comes on in this display if the tailgate or any door is not closed tightly. If a brake light does not work, the BRAKE LAMP indicator comes on when you push the brake pedal with the ignition switch ON (II). A burned out brake light is a hazard when drivers behind you cannot tell you are braking. Have your brake lights repaired right away. All the lights in the monitor display come on for a few seconds when you turn the ignition switch ON (II).

Instruments and Controls

Main MenuTable of ContentsstIndicator Lights

Turn Signal and Hazard Warning Indicators

The left or right turn signal light blinks when you signal a lane change or turn. If the light does not blink or blinks rapidly, it usually means one of the turn signal bulbs is burned out (see page 178). Replace the bulb as soon as possible, since other drivers cannot see that you are signalling.

When you turn on the Hazard Warning switch, both turn signal lights blink. All turn signals on the outside of the car should flash.

DRL

"Daytime Running Lights" Indicator

Canadian models only This indicator lights when you turn the ignition to ON (II) with the headlight switch off and the parking brake set. It should go off if you turn on the headlights or release the parking brake. If it comes on at any

Instruments and Controls

other time, it means there is a problem with the DRL. There may also be a problem with the high beam headlights.

High Beam Indicator

This light comes on with the high beam headlights. See page 42 for information on the headlight controls.

Cruise Control Indicator

CRUISE CONTROL This lights when you set the cruise control. See page 48 for information on operating the cruise control.

Low Fuel Indicator

This light comes on as a reminder that you must refuel soon.

Shift Lever Position Indicator

This indicator shows which shift position the shift lever is in. The "D4" indicator comes on for a few seconds when you turn the ignition switch ON (II). If it flashes while driving (in any shift position), it indicates a possible problem in the transmission. Avoid rapid acceler- ation and have the transmission checked by an authorized Honda dealer as soon as possible.

Main MenuTable of ContentsstFUEL GAUGE

SPEEDOMETER

TRIP METER

TEMPERATURE GAUGE

MAINTENANCE REQUIRED INDICATOR

ODOMETER

TRIP METER RESET BUTTON

Speedometer U.S. Models This shows your speed in miles per hour (mph). The smaller inner numbers are the speed in kilometers per hour (km/h).

Trip Meter This meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it. To reset it, push the trip meter reset button.

Canadian Models This shows your speed in kilometers per hour (km/h). The smaller inner numbers are the speed in miles per hour (mph).

Gauges

Odometer The odometer shows the total dis- tance your car has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under federal law (in the U.S.) and provincial regulations (in Canada) to disconnect, reset, or alter the odometer with the intent to change the number of miles or kilometers indicated.

Instruments and Controls

Main MenuTable of ContentsstGauges

Temperature Gauge This shows the temperature of the engine's coolant. During normal operation, the pointer should rise from the bottom white mark to about the middle of the gauge. In severe driving conditions, such as very hot weather or a long period of uphill driving, the pointer may rise to the upper white mark. If it reaches the red " H" (Hot) mark, pull safely to the side of the road. Turn to page 202 for instructions and precautions on checking the engine's cooling system.

Fuel Gauge This shows how much fuel you have. It is most accurate when the car is on level ground. It may show slightly more or less than the actual amount when you are driving on curvy or hilly roads.

The gauge stays at the same fuel level reading after you turn off the ignition. When you add fuel, the gauge slowly changes to the new reading after you turn the ignition back ON (II).

Instruments and Controls

Maintenance Required Indicator

SLOT

INDICATOR

The indicator reminds you when it is time for scheduled maintenance. When it nears 12,000 km (7,500
miles) since the last maintenance, the indicator will turn yellow. If you exceed 12,000 km (7,500 miles), the indicator will turn red. Your dealer will reset the indicator when he performs the scheduled maintenance. If someone else performs the maintenance, reset the indicator by inserting your key in the slot beside the indicator.

Main MenuTable of ContentsstControls Near the Steering Wheel

HAZARD WARNING LIGHT

SHIFT LEVER

REAR WINDOW DEFOGGER

SUNROOF SWITCH

The two levers on the steering column contain controls for driving features you use most often. The left lever controls the turn signals, headlights, and high beams. The right lever controls the windshield wipers.

The rear window defogger switch and hazard warning switch are on the dashboard under the center air vent.

The controls near the left air vent are for the sunroof, cruise control and instrument panel brightness.

The lever on the underside of the steering column allows you to tilt the steering wheel.

CRUISE CONTROL

INSTRUMENT BRIGHTNESS

HEADLIGHTS/ TURN SIGNALS

TILT ADJUSTMENT

WINDSHIELD WIPERS/WASHERS

Instruments and Controls

Main MenuTable of ContentsstControls Near the Steering Wheel

Headlights

If you leave the lights on with the ignition switch in ACCESSORY (I) or LOCK (0), you will hear a reminder chime when you open the driver's door.

The rotating switch on the left lever controls the lights. Turning this switch to the first position " " turns on the parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights. Turning the switch to the second position "

" turns on the headlights.

To change between low beams and high beams, pull back on the turn signal lever until you hear a click, then let go. The blue high beam indicator will light (see page 38).

Instruments and Controls

To flash the high beams, pull back and hold the turn signal lever. Release the lever and the high beams will go off.

The high beams will stay on for as long as you hold the lever, no matter what position the headlight switch is in.

Daytime Running Lights (Canadian Models) With the headlight switch off, the high beam headlights come on with reduced brightness when you turn the ignition switch to ON (II) and release the parking brake. They remain on until you turn the ignition off, even if you set the parking brake.

The headlights revert to normal operation when you turn them on with the switch.

Main MenuTable of ContentsstInstrument Panel Brightness

Turn Signals

Controls Near the Steering Wheel

To signal a lane change, push lightly on the turn signal lever in the proper direction and hold it. The lever will return to the center position as soon as you release it.

The knob on the dashboard to the left of the steering column controls the brightness of the instrument panel lights. Push the knob to get it to pop out. Turn the knob to adjust the brightness.

TURN SIGNAL LEVER

Signal a turn or lane change with this lever. Push down on the lever to signal a left turn, and up to signal a right turn. If you push it up or down all the way, the turn signal continues to blink even when you release the lever. It shuts off automatically as you complete the turn.

Instruments and Controls

Main MenuTable of ContentsstControls Near the Steering Wheel

Windshield Wipers

Windshield Washers

To operate the wipers in mist mode, push the control lever down. The wipers run at high speed until you release the lever. This gives you a quick way to clear the windshield.

To clean the windshield, pull back on the wiper control lever. The washers spray until you release the lever. The wipers run at low speed while you're pulling the lever, then complete one more sweep of the windshield after you release it.

The right lever controls the wind- shield wipers and washers. The rotary switch at the end of the lever has three positions: INT — intermittent LO — low speed HI — high speed

In intermittent, the wipers operate every few seconds. In low speed and high speed, the wipers run continu- ously.

Instruments and Controls

Main MenuTable of ContentsstRear Window Wiper and Washer

Hazard Warning

Rear Window Defogger

Controls Near the Steering Wheel

The rear window wiper switch is located next to the windshield wiper switch.

To activate the rear windshield wiper, turn the switch "ON". If you wish to use the wiper and washer, turn and hold the switch one position up from "ON". To use the washer only, turn and hold the switch one position down from "OFF".

Push the red button to the left of the clock to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your car is disabled.

The rear window defogger will clear fog, frost, and thin ice from the window. Push the defogger button to turn it on and off. The light in the button lights to show the defogger is on. If you do not turn it off, the defogger will shut itself off after about 25 minutes. It also shuts off when you turn off the ignition. You have to turn it on again when you restart the car.

CONTINUED

Instruments and Controls

Main MenuTable of ContentsstControls Near the Steering Wheel

Make sure the rear window is clear and you have good visibility before starting to drive.

The defogger wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side to side.

Steering Wheel Adjustment You can adjust the steering wheel height to suit your preference. Do this before you begin driving.

Adjusting the steering wheel position while driving may cause you to lose control of the car and be seriously injured in a crash.

Adjust the steering wheel only when the car is stopped.

Instruments and Controls

1. Adjust the seat so you are a

comfortable distance from the pedals.

2. The lever to tilt the steering wheel

is under the steering column to the left. Push this lever all the way down.

Main MenuTable of ContentsstControls Near the Steering Wheel

3. Move the steering wheel up or

down to the desired position. Position the wheel so you can see all the instrument panel gauges and warning lights. Push the lever up to lock the steering wheel in that position.

4. Make sure you have securely

locked the steering wheel in place by trying to move it up and down.

Instruments and Controls

Main MenuTable of ContentsstSteering Wheel Controls

Cruise Control Cruise control allows you to maintain a set speed above 25 mph (40 km/h) without keeping your foot on the accelerator pedal. It is for cruising on straight, open highways. It is not recommended for conditions such as city driving, winding roads, slippery roads, heavy rain, or bad weather. You should have full control of the car under those conditions.

Using the Cruise Control

CRUISE CONTROL MASTER SWITCH

Improper use of the cruise control can lead to a crash.

Use the cruise control only when traveling on open highways in good weather.

1. Push in the Cruise Control Master

Switch to the left of the steering column. The indicator in the switch will light.

2. Accelerate to the desired cruising

speed above 25 mph (40 km/h).

Instruments and Controls

Main MenuTable of ContentsstChanging the Set Speed You can increase the set cruising speed in either of two ways:

RESUME/ accel

Press and hold the RESUME/ accel button. The car will acceler- ate slowly. When you reach the desired cruising speed, release the button.

Push on the accelerator pedal. Ac- celerate to the desired cruising speed and press the SET/decel button.

SET/decel

3. Press and hold the SET/decel

button on the steering wheel until the CRUISE CONTROL light on the instrument panel comes on. This shows the system is now activated.

The set speed may vary slightly, particularly on hills.

Steering Wheel Controls

You can decrease the set cruising speed in either of two ways:

Press and hold the SET/decel button. The car will decelerate. Release the button when you reach the desired speed.

Tap the brake pedal lightly with your toot. The CRUISE CONTROL light on the instru- ment panel will go out. When the car slows to the desired speed, press the SET/decel button. The car will then maintain the desired speed.

CONTINUED

Instruments and Controls

Main MenuTable of ContentsstSteering Wheel Controls

Even with the cruise control turned on, you can still use the accelerator pedal to speed up for passing. After completing the pass, take your foot off the accelerator pedal. The car will return to the set cruising speed.

Resting your foot on the brake or clutch pedal will cause the cruise control to cancel.

Instruments and Controls

Cancelling the Cruise Control Any of these actions cause the cruise control to cancel.

Tap the brake pedal.

Press the SET/decel and RE- SUME/accel buttons at the same time.

Press the Cruise Control Master Switch.

When you tap the brake pedal, or press the SET and RESUME buttons at the same time, the CRUISE CONTROL light on the instrument panel will go out and the car will begin to slow down. You can use the accelerator pedal in the normal way.

If you use the brake pedal to cancel cruise control, the system retains the previously-set cruising speed. To return to that speed, accelerate to above 25 mph (40 km/h) and press the RESUME/accel button until the CRUISE CONTROL light comes on. The car will accelerate to the same cruising speed as before.

If you cancel cruise control by pressing the SET and RESUME buttons at the same time, the previously-set cruising speed is erased. To use the cruise control, accelerate to the desired cruising speed and press the SET/decel button.

Pressing the Cruise Control Master Switch turns the system completely off and erases the previous cruising speed from memory. To use the system again, refer to Using the Cruise Control.

Main MenuTable of ContentsstSteering Wheel Controls, Keys and Locks

Horn

HORN BUTTONS

Keys

KEY NUMBER PLATE

VALET KEY

MASTER KEY

Press either of the buttons on the steering wheel spokes to sound the horn.

Your car comes with two kinds of keys: a master key and a valet key. The master key fits all locks on your car:

Ignition Doors Glove box Tailgate

The valet key only works the ignition and the door locks. You can keep the glove box locked when you leave your car and valet key at a parking facility.

You should have received a key number plate with your set of keys. You will need this key number if you ever have to replace a lost key. Store this plate in a safe place.

When replacing keys, use only Honda-approved key blanks.

Instruments and Controls

Main MenuTable of ContentsstSTART (III) — Use this position only to start the engine. The switch returns to ON when you let go of the key.

You will hear a reminder beeper if you open the driver's door with the key in the LOCK or ACCESSORY position. Remove the key to turn it off.

Keys and Locks

Ignition Switch

The ignition switch is on the right side of the steering column. It has tour positions: LOCK (0), ACCES- SORY (I), ON(II), and START (III).

Instruments and Controls

LOCK (0) — You can insert or remove the key only in this position. When you turn the key from LOCK to ACCESSORY, you may have to turn the steering wheel to release the anti-theft lock. To switch from ACCESSORY to LOCK, you must push the key in slightly as you turn it. Your vehicle must also be in Park. The anti-theft lock will lock the steering column when you remove the key.

ACCESSORY (I) — In this position, you can operate the audio system and cigarette lighter.

ON (II) — This is the normal key position when driving. All features and accessories on the car are usable. Several of the lights on the instru- ment panel come on as a test when you turn the ignition switch from ACCESSORY to ON (see page 35).

Main MenuTable of ContentsstPower Door Locks

MASTER DOOR LOCK SWITCH

LOCK TAB

Each front door has a master door lock switch. Either switch locks and unlocks all doors. Push the switch down to lock all doors, and up to unlock them. The lock tab on the tailgate also locks and unlocks when you use the master door lock switch.

Each door also has a lock tab on the top. When you push down the lock tab on the driver's door, all the doors and the tailgate lock. Pulling up the lock tab on the driver's door unlocks only that door. The lock tab on each passenger's door locks and unlocks only that door.

Keys and Locks

The front doors can be locked and unlocked from the outside with the key. In addition, all doors and the tailgate lock when you use the key to lock either front door from the out side. All doors and the tailgate unlock immediately if you use the key to unlock the passenger's side door. To unlock the doors and tailgate from the driver's side, turn the key clockwise and hold it there for several seconds.

Instruments and Controls

Main MenuTable of ContentsstKeys and Locks

Remote Transmitter U.S. EX model

You can lock and unlock your car using the remote transmitter. If you push "LOCK" on the transmitter, all doors and the tailgate will lock.

If you push "UNLOCK" once, only the driver's door will unlock; if you push "UNLOCK" again, all doors and the tailgate will unlock.

Instruments and Controls

If you use the unlock feature on the remote transmitter, and a door or the tailgate is not opened within 20
seconds, all doors and the tailgate will automatically lock. The remote transmitter will not work if the key is in the ignition.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance should void the user's authority to operate the equipment.

Childproof Door Locks

LEVER

The childproof door locks are designed to prevent children seated in the rear from accidentally opening the rear doors. Each rear door has a lock lever near the edge. With the lever in the LOCK position, the door cannot be opened from the inside regardless of the position of the lock tab. To open the door, pull the lock tab up and use the outside door handle.

Main MenuTable of ContentsstTailgate

Glove Box

Use your key to lock and unlock the tailgate. (On the U.S. EX model, your remote transmitter will also lock and unlock the tailgate.)

Open the glove box by pulling the bottom of the handle. Close it with a firm push. Lock or unlock the glove box with the master key.

To open the tailgate, pull the handle, then lift up the tailgate.

Keys and Locks

An open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt.

Always keep the glove box closed while driving.

Instruments and Controls

Main MenuTable of ContentsstSeats

Passenger Seating

Seat Adjustments

Six-passenger model The six-passenger model has separate seats with armrests for two front passengers, separate seats with armrests for two passengers in the second row, and a bench seat for two passengers in the third row.

For greater cargo capacity, the seats in the second row can be removed, and the bench seat in the third row can be folded into the floor.

Seven-passenger model The seven-passenger model has separate seats with armrests for two front passengers, a bench seat for three passengers in the second row, and a bench seat for two passengers in the third row. For greater cargo capacity, the seat in the second row can be folded out of the way in sections, and the bench seat in the third row can be folded into the floor.

Adjust the seat before you start driving.

To adjust the seat forward and backward, pull up on the lever under the seat cushion's front edge. Move the seat to the desired position and release the lever. Try to move the seat to make sure it is locked in position.

Instruments and Controls

Main MenuTable of ContentsstSeats

passenger model, pull up on the lever on the side of the seat-back. Move the seat-back to the desired position and release the lever. Let the seat-back latch in the new position.

Driver's Seat Power Height Adjustment

Reclining the seat-back can decrease the protection you get from your seat belt in a crash.

You can slide under the seat belt and be seriously injured.

Adjust the seat-back to an upright position and sit well back in the seat.

Adjust the seat-back before you start driving. The seat-backs should be in an upright position for you and your passengers to get the most protec- tion from the seat belts.

To change the seat-back angle of the front seats, or the second-row seats in the six passenger model, pull up on the lever on the outside of the seat bottom. To adjust the seat-back angle of the second seat in the seven-

U.S. EX model only The height of your driver's seat is power adjustable. Pull up the switch to raise the seat. Push it down to lower the seat.

Instruments and Controls

Main MenuTable of ContentsstSeats

Head Restraints

KNOB

The head restraints are designed to help reduce the risk of neck injuries. Your Honda has adjustable head restraints in all the outside seating positions. Adjust the head restraint so the top is even with the tops of your ears.

Instruments and Controls

Third Seat Access Six-passenger model

To get into or out of the third row seat, walk between the second row seats.

The head restraints adjust for height. You need both hands to adjust the restraint. Do not attempt to adjust it while driving. To raise it, pull upward. To lower the restraint, press the release button and push the restraint down.

To remove a head restraint for cleaning or repair, pull it up as far as it will go. Press the release button and pull the restraint out of the seat- back.

Driving your vehicle without head restraints can lead to a serious injury to you and your passengers in a crash.

Make sure the head restraints are in place and adjusted properly before driving.

Main MenuTable of ContentsstSeven-passenger model

Move the second seat back into place by pivoting the seat down. Make sure it locks to the floor. Pull the seat-back angle adjustment lever forward and push the seat-back to the desired position, then release the lever. Make sure the seat is securely locked in place.

LOCK RELEASE LEVER

Pull the seat-back angle adjustment lever on the second row seat to tilt the seat-back forward. Pull the lock release lever and pivot the seat up out of the way.

Seats

Removing the Second Seats in the Six-Passenger Model

LOCK RELEASE LEVER

Both seats can be removed to give more cargo capacity.

To remove a seat, unlock the seat from the floor by pulling both lock release levers up at the same time and pulling up on the rear of the seat.

CONTINUED

Instruments and Controls

Main MenuTable of ContentsstTo reinstall a seat, hook the front of the seat to the floor, then push the back into the locks. Make sure both the front and the back of the seat are securely fastened down before driving.

Folding the Second Seats in the Seven-Passenger Model The left and right halves of the second seat can be folded up separately to create more cargo space.

Seats

Unhook the front of the seat from the floor by pulling it back slightly, then pivoting it upward.

Always remove an unlocked seat from the vehicle before driving. A seat that is not locked in place could fly around and cause injury in a sudden stop or crash.

Instruments and Controls

Main MenuTable of ContentsstSEAT-BACK ANGLE ADJUSTMENT LEVER

RIVET

Reclining the Second Seat Seven-passenger model only

Seats

LOCK RELEASE LEVER

FASTENING STRAP

Pull the seat-back angle adjustment lever and tilt the seat-back forward. Then pull the lock release lever and pivot the seat forward.

Pull out the fastening strap. Hook the ring on the fastening strap to the rivet on the side of the seat-back. Make sure the seat is secure.

Reverse this procedure to return the seat to the upright position. Make sure you store the fastening strap properly, and that the seat is locked securely before driving.

You can recline the seat-backs on the second seat so they are level with the seat cushion of the third seat, making a large, cushioned area. To do this:

1. Remove the head restraints. Store them in the pocket in the left side panel behind the third seat.

CONTINUED

Instruments and Controls

Main MenuTable of ContentsstSeats

ANGLE ADJUSTMENT LEVER

Folding the Third Seat in All Models

SLIDE LEVER

2. Lift the lever and slide the seat

forward as far as it will go. Pull the seat-back angle adjustment lever and pivot the seat-back backward. Release the lever when the seat- back is even with the cushion on the third seat.

Reverse this procedure to return the second seat to the upright position. Make sure you install the head restraints before driving (see page 58).

Instruments and Controls

KNOB

2. Unlock the seat-back by turning

the knob. Push the seat-back forward.

To create more cargo space, you can fold the third seat into the floor recess. To fold the third seat:

1. Remove the head restraints. Store them in the pocket in the left side panel.

Main MenuTable of ContentsstSeats

KNOB

3. Turn the knob on the back of the

seat cushion while you pull the entire seat towards you. Pivot the seat into the floor recess.

KNOB

To return the seat to the upright position:

1. Pull the seat out of the recess by pulling on the handle. Pivot the seat forward all the way.

2. Turn the knob on the seat-back and pull the seat-back upright. Make sure the seat is securely locked in place.

3. Reinstall the head restraints.

Instruments and Controls

Main MenuTable of ContentsstPower Windows

Your car's windows are electrically- powered. Turn the ignition switch to ON (II) to raise or lower any window.

Each door has a switch that controls its window. To open the window, push the switch down and hold it. Release the switch when you want the window to stop. Close the window by pulling back on the switch and holding it.

Instruments and Controls

The master control panel also con- tains these extra features:

AUTO — To open the driver's window fully, push the window switch firmly down and release it. The window automatically goes all the way down. To stop the window from going all the way down, pull back on the window switch briefly.

DRIVER'S WINDOW SWITCH

MAIN SWITCH

The driver's armrest has a master power window control panel. To open any of the passengers' windows, push down on the appropriate switch and hold it down until the window reaches the desired position. To close the window, pull back on the window switch. Release the switch when the window gets to the position you want.

To open the driver's window only partially, push the window switch down lightly and hold it. The window will stop as soon as you release the switch.

The AUTO function only works to lower the driver's window. To raise the window, you must pull back on the window switch and hold it until the window reaches the desired position.

Main MenuTable of ContentsstThe MAIN switch controls power to the passengers' windows. With this switch off, the passengers' windows cannot be raised or lowered. The MAIN switch does not affect the driver's window. Keep the MAIN switch off when you have children in the car so they do not injure them- selves by operating the windows unintentionally.

Closing a power window on a child's hands or fingers can cause serious injury.

Make sure your children are away from the windows before closing them.

Power Windows, Sunroof

Sunroof

SUNROOF SWITCH

On some models Use the switch on the dashboard to open and close the sunroof. The ignition must be ON (II). Push and hold the switch to open the sunroof. Release the switch when the sunroof reaches the desired position. To close the sunroof, press and hold the

switch.

CONTINUED

Instruments and Controls

Main MenuTable of ContentsstSunroof, Mirrors

Mirrors

Closing the sunroof on someone's hands or fingers can cause serious injury.

Make sure passengers are clear of the sunroof before closing it.

NOTICE

TAB

If yon try to open the sunroof in below- freezing temperatures, or when it is covered with snow or ice, yon can damage the sunroof panel or motor.

Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving.

The inside mirror has day and night positions. The night position reduces glare from headlights behind you. Flip the tab on the bottom edge of the mirror to select the day or night position.

Instruments and Controls

Main MenuTable of ContentsstAdjusting the Power Mirrors

SELECTOR SWITCH

Mirrors

ADJUSTMENT SWITCH

Adjust the outside mirrors with the adjustment switch on the driver's door armrest:

3. Push the appropriate edge of the

adjustment switch to move the mirror right, left, up or down.

1. Turn the ignition switch ON (II).

2. Move the selector switch to L

(driver's side) or R (passenger's side).

4. When you finish, move the

selector switch to the center (off) position. This turns off the adjustment switch so you can't move a mirror out of position by accidentally bumping it.

The outside mirror on the passenger's side has curved glass. Objects look farther away than they are. Use this mirror to get a "wide view". Don't use it to judge the distance of things behind you.

Instruments and Controls

Main MenuTable of ContentsstParking Brake, Digital Clock

Parking Brake

NOTICE

Driving the car with the parking brake applied can damage the rear brakes and axles.

Digital Clock

HOUR

MIN

RESET

PARKING BRAKE LEVER

To apply the parking brake, pull the lever up fully. To release it, pull up slightly, push the button, and lower the lever. The parking brake light on the instrument panel should go out when the parking brake is fully released (see page 36). If you try to drive the car without releasing the parking brake, the ABS cannot work properly.

Instruments and Controls

The digital clock displays the time with the ignition switch ON (II). To set the clock:

1. Turn the ignition switch ON (II) to

display the time.

Main MenuTable of Contentsst2. Press and hold the HOUR button

until the hour advances to the desired time.

3. Press and hold the MIN. button until the numbers advance to the desired time.

You can use the RESET button to quickly set the time to the nearest hour. If the displayed time is before the half hour, pressing the RESET button sets the clock back to the previous hour. If the displayed time is after the half hour, pressing the RESET button sets the clock for- ward to the beginning of the next hour. For example:

1:06 would RESET backward to 1:00. 1:52 would RESET forward to 2:00.

Digital Clock, Beverage Holder

Beverage Holder

To use the front beverage holder, pull on the front. Push the holder all the way in to close it.

The beverage holder for the second seat passengers is located in the armrest on each rear door.

The third seat also has a beverage holder in each side panel.

CONTINUED

Instruments and Controls

Main MenuTable of ContentsstBeverage Holder, Dashboard Compartment

Spilled liquids can also damage the upholstery, carpeting, and electrical components in the interior.

Dashboard Compartment

Open the dashboard compartment by squeezing the handle. Close it with a firm push.

Use the beverage holder only when the car is parked. If you place cups in the holder while driving, the liquid may spill when you go over bumps or around corners. Liquid can also spill from the holders by the second seat when you close the rear doors. If the spilled liquid is very hot, it can scald you or your passengers.

Instruments and Controls

Main MenuTable of ContentsstCenter Pocket

Coin Box

Vanity Mirror

Center Pocket, Coin Box, Vanity Mirror

Open the center pocket by pulling the handle. Close it with a firm push. The light in the pocket comes on when the instrument panel lights are on.

COIN BOX

To open the coin box, pull the upper edge. Close it with a firm push.

To use the vanity mirror, pull down either sun visor and swing down the cover.

The passenger's vanity mirror is lighted. The light beside the mirror comes on only when the light switch is turned on.

Instruments and Controls

Main MenuTable of ContentsstCigarette Lighter, Ashtrays

Cigarette Lighter

Ashtrays

CIGARETTE LIGHTER

The ignition switch must be in ACCESSORY (I) or ON (II) for the cigarette lighter to work. To heat up the lighter, push it in. It will pop out when it is ready for use. Do not hold the lighter in while it is heating up, you could cause it to overheat.

ASHTRAY

ASHTRAY

Open the front ashtray by pulling on the bottom edge. Push it in to close it. To remove the ashtray for emptying, push down on the metal plate inside, then pull the ashtray out completely.

The rear ashtray is in the armrest on the left rear door. To use the rear ashtray, swing the lid open. To remove the rear ashtray, open the lid and pull it straight up.

Instruments and Controls

Main MenuTable of ContentsstAshtrays, Interior Lights

NOTICE

Ceiling Lights

Spotlights

Use the ashtray only for cigarettes, cigars and other smoking materials. To prevent a possible fire and damage to your car, don't put paper or other things that can burn in the ashtray.

DOOR ACTIVATED

Your Honda has two ceiling lights. Each ceiling light has a three- position switch. In the OFF position, the lights do not come on. In the center position they come on when you open any door. In the ON position, they stay on continuously.

On some models Turn on the spotlight by pushing the button next to each light. Push the button again to turn it off.

Instruments and Controls

Main MenuTable of ContentsstInterior Lights

Tailgate Light

Courtesy Lights

The tailgate light has a two position switch. In the OFF (down) position, the light does not come on. In the ON (up) position, the light comes on when you open the tailgate.

Each door has a courtesy light. This light comes on when you open the door. Your car also has a courtesy light in the ignition switch. This light comes on when you open the driver's door. It remains on for several seconds after the door is closed.

Instruments and Controls

Main MenuTable of ContentsstThe heating and air conditioning system in your car provides a com- fortable driving environment in all weather conditions.

The audio sound system is very versatile. To get the most from this system, take the time to learn what the controls do. Some models have an anti-theft audio system that requires a code number to enable it.

Comfort and Convenience Features

Heating and Cooling........................ 76
What Each Control Does............ 78
How to Use the System............... 79

Controlling Air Flow

Direction............................... 79
Ventilation................................ 79
To Cool with A/C.................... 80
To Heat..................................... 80
To Heat and Dehumidify

with Air Conditioning.......... 81
To Defog and Defrost............. 82
To Turn Everything Off ............. 82
Rear A/C Unit.............................. 83

Audio System (US EX and

Canadian EX).......................... 84

AM/FM/Cassette Stereo Audio

System...................................... 84
Operating the Radio.................... 85
Finding the Radio Station........... 85
Presetting..................................... 86
Adjusting the Sound.................... 87
Radio Frequencies....................... 88
Operating the Cassette Player... 89
Cassette Search Functions......... 90
Caring for Cassettes.................... 91

Audio System (US EX).................... 92

AM/FM/Cassette Stereo Audio

System....................................... 92
Operating the Radio.................... 93
Finding the Radio Station........... 93
Presetting..................................... 94
Adjusting the Sound.................... 96
Radio Frequencies....................... 97
Operating the Cassette Player... 98
Cassette Search Functions......... 99
Caring for Cassettes.................. 100
Operating the CD Player.......... 101
CD Error Indications................. 104
Caring for the Cassette Player..... 105
Theft Protection............................. 106

Comfort and Convenience Features

Main MenustHeating and Cooling

This system has full heating, venti- lation, and air conditioning capabi- lities. You can adjust the system controls to mix these in various combinations. The air flows into the interior at three possible levels, which you can select.

CENTER VENT

SIDE VENT

The direction of air flow from the vents in the center and each side of the dashboard is adjustable. Move the tab in the center of each vent up- and-down and side-to-side.

The heating and cooling system draws air through the exterior vents at the bottom of the windshield. Keep these vents clear of leaves and other debris.

The side vents can be opened and closed with the dials next to them.

Comfort and Convenience Features

Main MenuTable of ContentsstHeating and Cooling

Comfort and Convenience Features

Main MenuTable of ContentsstHeating and Cooling

What Each Control Does

Fan Control Lever Sliding this lever to the right increases the fan speed, which increases air flow.

Temperature Control Lever Sliding this lever to the right increases the temperature of air flowing from the system.

Mode Buttons These buttons control the direction of air flow. The indicator light shows which button is controlling air flow.

Air Conditioning (A/C) Switch This switch turns the air condi- tioning ON and OFF. The indicator in the switch lights when the A/C is ON.