94
2013 FituuOperating the Switches Around the Steering WheeluTurn Signals
Turn Signals
Right Turn
The turn signals can be used when the ignition switch is in ON (w.
Left Turn
Light Switches
High Beams
Flashing the high beams
Low Beams
Turns on parking, side marker, tail, and rear license plate lights Turns on headlights, parking, side marker, tail, and rear license plate lights
Rotating the light switch turns the lights on and off, regardless of the position of the ignition switch. ■ High beams Push the lever forward until you hear a click. ■ Low beams When in high beams, pull the lever back to return to low beams. ■ Flashing the high beams Pull the lever back, and release it.
1Light Switches
If you remove the key from the ignition switch while the lights are on, a chime sounds when the driver’s door is opened.
Do not leave the lights on when the engine is off because it will cause the battery to discharge.
QRG
TOC
Index
Home
95
2013 FituuOperating the Switches Around the Steering WheeluFog Lights*
Fog Lights*
QRG
When the low beam headlights are on, turn the fog light switch on to use the fog lights.
1Fog Lights*
When the fog lights are on, the indicator in the instrument panel will be on.
2 Fog Light Indicator * P. 70
TOC
Index
Home
96
Fog Light Switch
Daytime Running Lights The high beam headlights come on slightly dimmer than normal when the following conditions have been met: • The ignition switch is in ON (w.
• The headlight switch is off, or in
• The parking brake is released.
The lights remain on even if you set the parking brake. Turning off the ignition switch will turn off the daytime running lights.
The high beam headlights return to the original brightness once the headlight switch is turned on.
* Not available on all models
2013 FituuOperating the Switches Around the Steering WheeluWipers and Washers
The windshield wipers and washers can be used when the ignition switch is in ON (w.
■ MIST The wipers run at high speed until you release the lever.
■ Wiper switch (OFF, INT, LO, HI) Change the wiper switch setting according to the amount of rain.
■ Washer Sprays while you pull the lever toward you. When you release the lever, the wipers make two or three more sweeps before stopping.
1Wipers and Washers
NOTICE Do not use the wipers when the windshield is dry. The windshield will get scratched, or the rubber blades will get damaged.
NOTICE In cold weather, the blades may freeze to the windshield, becoming stuck. Operating the wipers in this condition may damage the wipers. Use the defroster to warm the windshield, then turn the wipers on.
Turn the washers off if no washer fluid comes out. The pump may get damaged.
Wipers and Washers ■ Front Wiper/Washer
Pull to use washer.
MIST OFF INT: Low speed with intermittent LO: Low speed wipe HI: High speed wipe
Continued
QRG
TOC
Index
Home
97
2013 FituuOperating the Switches Around the Steering WheeluWipers and Washers
■ Rear Wiper/Washer
The rear wiper and washer can be used when the ignition switch is in ON (w.
If the wiper stops operating due to any obstacle such as the build-up of snow, park the vehicle in a safe place.
1Wipers and Washers
■ Wiper switch (OFF, ON) The wiper operates intermittently after completing a few sweeps.
■ Washer ( Sprays while you rotate the switch to this position.
Hold it to activate the wiper and to spray the washer. Once released, it stops operating after a few more sweeps.
Rotate the wiper switch to OFF, and turn the ignition switch to ACCESSORY (q or LOCK (0, then remove the obstacle.
The wiper motor is equipped with a breaker that may stop motor operation temporarily to prevent an overload. Wiper operation will return to normal within a few minutes, once the circuit has returned to normal.
ON: Intermittent OFF Washer
■ Operating in reverse When you shift the transmission to (R with the front wiper activated, the rear wiper operates automatically as follows even if its switch is off.
Front Wiper Position
Rear Wiper Operation
INT (Intermittent)
LO (Low speed wipe) HI (High speed wipe)
Intermittent
Continuous
QRG
TOC
Index
Home
98
2013 FitBrightness Control
Select/Reset Knob
uuOperating the Switches Around the Steering WheeluBrightness Control
1Brightness Control
Pressing the
knob switches the display.
If you turn the knob to the right until the brightness display is up to max, the beeper sounds. This cancels the reduced instrument panel brightness when the exterior lights are on.
The brightness can be set differently for when the exterior lights are on, and when they are off.
When the parking lights are turned on and the ignition switch is in ON (w, you can use the (select/reset) knob to adjust instrument
panel brightness. Brighten: Turn the knob to the right. Dim: Turn the knob to the left.
You will hear a beep when the brightness reaches minimum or maximum. The information display will return to its original state several seconds after you adjust the brightness.
■ Brightness level indicator The brightness level is shown on the information display while you are adjusting it.
QRG
TOC
Index
Home
99
2013 FituuOperating the Switches Around the Steering WheeluRear Defogger/Heated Door Mirror* Button
1Rear Defogger/Heated Door Mirror * Button
NOTICE When cleaning the inside of the rear window, be careful not to damage the heating wires. It is critical to wipe the window from side to side along the defogger heating wires.
This system consumes a lot of power, so turn it off when the window has been defogged. Also, do not use the system for a long period when the engine is idling. This may weaken the battery, making it difficult to start the engine.
Rear Defogger/Heated Door Mirror* Button
QRG
Models with navigation system
Press the rear defogger and heated door mirror button to defog the rear window and mirrors when the ignition switch is in ON (w.
TOC
Index
Home
100
Models without navigation system
* Not available on all models
2013 FituuOperating the Switches Around the Steering WheeluAdjusting the Steering Wheel
Adjusting the Steering Wheel The steering wheel height and distance from your body can be adjusted so that you can comfortably grip the steering wheel in an appropriate driving posture.
To adjust
To lock
1. Pull the steering wheel adjustment lever up.
u The steering wheel adjustment lever is
under the steering column.
2. Move the steering wheel up or down, and
in or out. u Make sure you can see the instrument
panel gauges and indicators.
3. Push the steering wheel adjustment lever
down to lock the steering wheel in position. u After adjusting the position, make sure
you have securely locked the steering wheel in place by trying to move it up, down, in, and out.
1Adjusting the Steering Wheel
3WARNING
Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.
Adjust the steering wheel only when the vehicle is stopped.
Make any steering wheel adjustments before you start driving.
QRG
TOC
Index
Home
101
2013 Fit1Adjusting the Mirrors
Keep the inside and outside mirrors clean and adjusted for best visibility.
Adjust the mirrors before you start driving.
2 Adjusting the Seat Positions P. 103
Adjusting the Mirrors
QRG
Interior Rearview Mirror Adjust the angle of the rearview mirror when you are sitting in the correct driving position.
■ Rearview Mirror with Day and Night Positions
TOC
Daytime Position
Tab
Up
Flip the tab to switch the position. The night position will help to reduce the glare from headlights behind you when driving after dark.
Down
Night Position
Power Door Mirrors
Selector Switch
You can adjust the door mirrors when the ignition switch is in ON (w.
■ Mirror position adjustment L/R selector switch: Select the left or right mirror. After adjusting the mirror, return the switch to the center position.
Mirror position adjustment switch: Press the switch left, right, up, or down to move the mirror.
Adjustment Switch
Index
Home
102
2013 FitAdjusting the Seats
Adjusting the Seat Positions
Allow sufficient space.
Move back.
■ Adjusting the front seat
Adjust the driver’s seat as far back as possible while allowing you to maintain full control of the vehicle. You should be able to sit upright, well back in the seat and be able to adequately press the pedals without leaning forward, and grip the steering wheel comfortably. The passenger’s seat should be adjusted in a similar manner, so that it is as far back from the front airbag in the dashboard as possible.
1Adjusting the Seats
3WARNING
Sitting too close to a front airbag can result in serious injury or death if the front airbags inflate.
Always sit as far back from the front airbags as possible while maintaining control of the vehicle.
The National Highway Traffic Safety Administration and Transport Canada recommend that drivers allow at least 10 inches (25 cm) between the center of the steering wheel and the chest.
Always make seat adjustments before driving.
1Adjusting the front seat
Once a seat is adjusted correctly, rock it back and forth to make sure it is locked in position.
Horizontal Position Adjustment Pull up on the bar to move the seat, then release the bar.
Driver’s seat is shown.
Seat-back Angle Adjustment Pull up the lever to change the angle.
Continued
QRG
TOC
Index
Home
103
2013 FituuAdjusting the SeatsuAdjusting the Seat Positions
■ Adjusting the Seat-Backs
Adjust the driver’s seat-back to a comfortable, upright position, leaving ample space between your chest and the airbag cover in the center of the steering wheel.
The front seat passenger should also adjust their seat-back to a comfortable, upright position.
Reclining a seat-back so that the shoulder part of the belt no longer rests against the occupant’s chest reduces the protective capability of the belt. It also increases the chance of sliding under the belt in a crash and being seriously injured. The farther a seat-back is reclined, the greater the risk of injury.
1Adjusting the Seat-Backs
3WARNING
Reclining the seat-back too far can result in serious injury or death in a crash.
Adjust the seat-back to an upright position, and sit well back in the seat.
Do not put a cushion, or other object, between the seat-back and your back.
Doing so may interfere with proper seat belt or airbag operation.
If you cannot get far enough away from the steering wheel and still reach the controls, we recommend that you investigate whether some type of adaptive equipment may help.
QRG
TOC
Index
Home
104
2013 Fit■ Adjusting the Head Restraints
Your vehicle is equipped with head restraints in all seating positions.
Head restraints are most effective for protection against whiplash and other rear- impact crash injuries when the center of the back of the occupant’s head rests against the center of the restraint. The tops of the occupant’s ears should be level with the center height of the restraint.
Position head in the center of the head restraint.
■ Adjusting the front head restraint positions
To raise the head restraint: Pull it upward.
To lower the head restraint: Push it down while pressing the release button.
uuAdjusting the SeatsuAdjusting the Seat Positions
1Adjusting the Head Restraints
3WARNING
Improperly positioning head restraints reduces their effectiveness and increases the likelihood of serious injury in a crash.
Make sure head restraints are in place and positioned properly before driving.
The driver’s and front passenger’s seats have active head restraints.
2 Active Head Restraints P. 107
Continued
QRG
TOC
Index
Home
105
2013 FituuAdjusting the SeatsuAdjusting the Seat Positions
■ Changing the Rear Seat Head Restraint Positions
A passenger sitting in a back seating position should adjust the height of their head restraint to an appropriate position before the vehicle begins moving. To raise the head restraint: Pull it upward.
To lower the head restraint: Push it down while pressing the release button.
■ Removing and Reinstalling the Head Restraints Head restraints can be removed for cleaning or repair.
3WARNING 1Removing and Reinstalling the Head Restraints
To remove a head restraint: Pull the restraint up as far as it will go. Then push the release button, and pull the restraint up and out.
Failure to reinstall, or correctly reinstall, the head restraints can result in severe injury during a crash.
To reinstall a head restraint: Insert the legs back in place, then adjust the head restraint to an appropriate height while pressing the release button. Pull up on the restraint to make sure it is locked in position.
Always replace the head restraints before driving.
QRG
TOC
Index
Home
106
2013 Fit■ Active Head Restraints The driver’s and front passenger’s seats have active head restraints. In a rear impact, an occupant properly secured by a seat belt will be pushed against the seat-back and the head restraint will move forward. This reduces the distance between the restraint and the occupant’s head, which helps reduce the likelihood of whiplash and injuries to the neck and upper spine.
uuAdjusting the SeatsuAdjusting the Seat Positions
1Active Head Restraints
In order for the active head restraints to operate properly: • Do not hang any items on the head restraints, or
from the restraint legs.
• Do not place any objects between an occupant and
the seat-back.
• Install each restraint in its proper location.
After a collision, the activated restraint should return to its normal position. If the restraint does not return to its normal position, or in the event of a severe collision, have the vehicle inspected by a dealer.
■ Maintain a Proper Sitting Position After all occupants have adjusted their seats and head restraints, and put on their seat belts, it is very important that they continue to sit upright, well back in their seats, with their feet on the floor, until the vehicle is safely parked and the engine is off. Sitting improperly can increase the chance of injury during a crash. For example, if an occupant slouches, lies down, turns sideways, sits forward, leans forward or sideways, or puts one or both feet up, the chance of injury during a crash is greatly increased. In addition, an occupant who is out of position in the front seat can be seriously or fatally injured in a crash by striking interior parts of the vehicle or being struck by an inflating front airbag.
1Maintain a Proper Sitting Position
3WARNING
Sitting improperly or out of position can result in serious injury or death in a crash.
Always sit upright, well back in the seat, with your feet on the floor.
QRG
TOC
Index
Home
107
2013 FituuAdjusting the SeatsuRear Seats
QRG
Rear Seats ■ Adjusting the Rear Seat-Backs
Pull the lever on the right to change the angle of the right half of the seat-back, and left for the left half.
TOC
Release Lever
■ Folding Down the Rear Seats
Anchor Buckle
1. Unlatch the detachable anchor from the anchor buckle and store the detachable anchor in the retractor housing.
Latch Plate
2. Pull the release lever and fold down the
seat-back.
Index
Home
108
Release Lever
1Folding Down the Rear Seats
The rear seat-backs can be folded down to accommodate bulkier items in the cargo area.
Never drive with a seat-back folded down and the tailgate open.
2 Exhaust Gas Hazard P. 61
To lock a seat-back upright, push it backwards until it locks. When returning a seat-back to it’s original position, push it firmly back. Also, make sure all rear shoulder belts are positioned in front of the seat- back, and the center shoulder belt is re-positioned in the guide.
Make sure that the folded seat-back does not press against the front passenger seat, as this can cause the front passenger seat weight sensor to work improperly.
2 Side Airbag Off Indicator P. 47
2013 Fit■ Folding the Rear Seat Up
Separately lift up the left and right halves of the rear seat cushions to make room for cargo area.
■ Lifting up the seat cushion 1. Make sure the seat belt buckles are in their
loops on the seat.
2. Pull up the rear seat cushion.
3. Fold the seat leg down.
4. Push the seat cushion firmly against the
seat-back to lock it.
Loop
Seat Leg
Seat Leg
■ Putting the seat in the original position 1. Hold the seat cushion in the upright
position, and pull up the seat leg fully. u The seat cushion can abruptly fall down
once you pull up the seat leg.
2. Slowly put down the seat cushion and set
the seat leg in the floor guide. u A latch comes out when the leg is set
properly.
Latch
Floor Guide
uuAdjusting the SeatsuRear Seats
1Folding the Rear Seat Up
After you fold the seat up, or put it back in the original position, make sure the seat is firmly secured by rocking it forward and back.
Check if there are any items on the seat before you pull the seat cushion up. Check if there are any obstacles around the floor guide before you put the seat back in the original position.
QRG
TOC
Index
Home
109
2013 FituuAdjusting the SeatsuArmrest
QRG
Armrest ■ Using the Driver’s Seat Armrest*
Pull down the armrest.
TOC
Index
Home
110
* Not available on all models
2013 FitInterior Lights/Interior Convenience Items
Interior Lights ■ Interior Light Switch
Door Activated Position
On
Off
■ ON The interior light comes on regardless of whether the doors are open or closed. ■ Door activated The interior light comes on in the following situations: • When any of the doors are opened. • You unlock the driver’s door. • You remove the key from the ignition
switch.
■ OFF The interior light remains off regardless of whether the doors are open or closed.
1Interior Light Switch
In the door activated position, the interior light fades out and goes off about 30 seconds after the doors are closed. The light goes off after 30 seconds in the following situations: • When you unlock the driver’s door but do not open
it.
• When you remove the key from the ignition switch
but do not open a door.
The interior light goes off immediately in the following situations: • When you lock the driver’s door. • When you close the driver’s door with the key in
the ignition switch.
• When you turn the ignition switch to ON (w.
If you leave any of the doors open without the key in the ignition switch, the interior light goes off after about 15 minutes.
■ Map Lights*
The map lights can be turned on and off by pressing the lenses.
* Not available on all models
Continued
QRG
TOC
Index
Home
111
2013 FituuInterior Lights/Interior Convenience ItemsuInterior Lights
■ Cargo Area Light
The light comes on when you open the tailgate.
QRG
TOC
Index
Home
112
2013 FituuInterior Lights/Interior Convenience ItemsuInterior Convenience Items
Interior Convenience Items ■ Glove Box
Pull the handle to open the glove box.
1Glove Box
3WARNING
An open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt.
Always keep the glove boxes closed while driving.
■ Upper Glove Box
Pull up on the lever to open the upper glove box.
Continued
QRG
TOC
Index
Home
113
2013 FituuInterior Lights/Interior Convenience ItemsuInterior Convenience Items
■ Beverage Holders
■ Front seat beverage holders
1Beverage Holders
NOTICE Spilled liquids can damage the upholstery, carpeting, and electrical components in the interior.
Be careful when you are using the beverage holders. Hot liquid can scald you.
■ Rear seat beverage holders
QRG
TOC
Index
Home
114
2013 FituuInterior Lights/Interior Convenience ItemsuInterior Convenience Items
■ Cargo Floor Box*
Cargo Floor Box
Pull up the strap and open the cargo area floor lid.
Strap
■ Accessory Power Socket The accessory power socket can be used when the ignition switch is in ACCESSORY (q or ON (w.
Open the cover to use it.
* Not available on all models
Continued
1Accessory Power Socket
NOTICE Do not insert an automotive type cigarette lighter element. This can overheat the power socket.
The accessory power socket is designed to supply power for 12 volt DC accessories that are rated 120 watts or less (10 amps).
To prevent battery drain, only use the power socket with the engine running.
QRG
TOC
Index
Home
115
2013 FituuInterior Lights/Interior Convenience ItemsuInterior Convenience Items
QRG
■ Coat Hook
There is a coat hook on the rear left grab handle. Pull it down to use it.
1Coat Hook
The coat hook is not designed for large or heavy items.
■ Seat Under Box Located at the back of the driver’s side rear seat cushion.
1. Fold up the driver’s side rear seat.
2 Folding the Rear Seat Up P. 109
2. Turn the knobs to open the box. Align the dot marks on the knobs and the box cover when closing the box.
TOC
Index
Home
116
2013 FituuInterior Lights/Interior Convenience ItemsuInterior Convenience Items
■ Cargo Hooks*
Hook
Use floor cargo hooks to secure luggage in the cargo area.
1Cargo Hooks*
NOTICE Do not hang a large object or an object that weighs more than 2.2 lbs (1 kg) on the side cargo hooks. Hanging heavy or large objects may damage the hooks.
Hook
There are also hooks on both sides of the cargo area.
Hook
* Not available on all models
QRG
TOC
Index
Home
117
2013 FitHeating and Cooling *
Using Vents, Heating and A/C*
QRG
Dashboard vents
Dashboard and floor vents
Floor vents
Floor and defroster vents
Defroster vents
TOC
Index
Home
118
Fan Control Dial Adjusts the fan speed. Rotate the dial all the way to OFF to turn everything off.
Temperature Control Dial Adjusts the interior temperature.
* Not available on all models
Mode Control Dial Change airflow.
A/C Button * Press to cool the interior or dehumidify while heating.
Fresh Air/Recirculation Lever This lever controls the source of the air going into the system.
(Recirculation) Mode:
Recirculates air from the vehicle’s interior through the system.
(Fresh Air) Mode:
Maintains outside ventilation. Keep the system in fresh air mode in normal situations.
2013 FituuHeating and Cooling *uUsing Vents, Heating and A/C*
■ Heating
The heater uses heat from the engine coolant to warm the air. 1. Adjust the fan speed using the fan control
dial.
2. Select
and
3. Adjust the temperature using the
temperature control dial.
■ To rapidly warm up the interior 1. Set the fan to the maximum speed.
2. Select
3. Set the temperature to maximum heat.
4. Select
■ To dehumidify the interior * When used in combination with the heater, the air conditioning system makes the interior warm and dry and can prevent the windows from fogging up. 1. Turn the fan on.
2. Press the A/C button to turn on the air conditioning.
3. Select
and
. Adjust the temperature to your preference.
* Not available on all models
Continued
1To rapidly warm up the interior
Change to fresh air mode as soon as the interior gets warm enough. The windows may fog up if kept in recirculation mode.
QRG
TOC
Index
Home
119
2013 FituuHeating and Cooling *uUsing Vents, Heating and A/C*
QRG
■ Cooling*
1. Adjust the fan speed using the fan control
dial.
1To rapidly cool down the interior
If the interior is very warm, you can cool it down more rapidly by partially opening the windows.
2. Select 3. Adjust the temperature using the
and
temperature control dial.
4. Press the A/C button (the indicator on).
■ To rapidly cool down the interior 1. Set the fan to the maximum speed. 2. Set the temperature to maximum cool. 3. Select
■ Defrosting the Windshield and Windows*
1. Select
turns the air conditioning system
on.
2. Select
■ To rapidly defrost the windows 1. Set the fan to the maximum speed.
2. Select 3. Select 4. Set the temperature to maximum heat.
* Not available on all models
TOC
Index
Home
120
1Defrosting the Windshield and Windows*
For your safety, make sure you have a clear view through all the windows before driving. Do not set the temperature near the upper or lower limit. When cold air hits the windshield, the outside of the windshield may fog up. If the side windows fog up, adjust the vents so that the air hits the side windows.
1To rapidly defrost the windows
After defrosting the windows, switch over to fresh air mode. If you keep the system in recirculation mode, the windows may fog up from humidity. This impedes visibility.
2013 FitFeatures
QRG
This chapter describes how to operate technology features.
Audio System
About Your Audio System................ 122
USB Adapter Cable* ........................ 123
Auxiliary Input Jack .......................... 123
Audio Antenna ................................ 124
Audio System Theft Protection ......... 124
Audio System Basic Operation ........ 125
Adjusting the Sound ........................ 126
Playing the FM/AM Radio................. 127
Playing a CD .................................... 129
Playing an iPod®
*............................. 131
Playing a USB Flash Drive* ............... 133
Audio Error Messages
CD Player......................................... 135
iPod®/USB Flash Drive*..................... 136
General Information on the Audio
System
Recommended CDs ......................... 137
Compatible iPod® and USB Flash Drives* .139
Bluetooth® HandsFreeLink®
Using HFL ........................................ 140
HFL Menus ...................................... 142
Index
Home
121
* Not available on all models
2013 FitAudio System
QRG
About Your Audio System On models with navigation system, see the Navigation System Manual for operation of the audio system, and Bluetooth®HandsFreeLink®.
The audio system features FM/AM radio. It can also play audio CDs, WMA/MP3/AAC files, iPod®, and USB flash drives.
You can operate the audio system from the buttons and switches on the panel.
1About Your Audio System
Video CDs, DVDs, and 3-inch (8-cm) mini CDs are not supported.
iPod® is a registered trademark owned by Apple Inc.
State or local laws may prohibit the operation of handheld electronic devices while operating a vehicle.
Auxiliary Input Jack
iPod®
USB Flash Drive
TOC
Index
Home
122
2013 FitUSB Adapter Cable*
1. Unclip the USB connector and loosen the
1USB Adapter Cable*
uuAudio SystemuUSB Adapter Cable*
adapter cable.
2. Install the iPod® dock connector or the USB
flash drive to the USB connector.
Auxiliary Input Jack Use the jack to connect standard audio devices.
1. Open the AUX cover.
2. Connect a standard audio device to the
input jack using a 1/8 inch (3.5 mm) stereo miniplug. u The audio system automatically switches
to the AUX mode.
* Not available on all models
• Do not leave the iPod® or USB flash drive in the
vehicle. Direct sunlight and high temperatures may damage it.
• Do not use an extension cable with the USB
adapter cable.
• Do not connect the iPod® or USB flash drive using a
hub.
• Do not use a device such as a card reader or hard
disk drive, as the device or your files may be damaged.
• We recommend backing up your data before using
the device in your vehicle.
• Displayed messages may vary depending on the
device model and software version.
If the audio system does not recognize the iPod®, try reconnecting it a few times or reboot the device. To reboot, follow the manufacturer’s instructions provided with the iPod® or visit www.apple.com/ ipod.
1Auxiliary Input Jack
To switch the mode, press any of the audio mode buttons. You can return to the AUX mode by pressing the AUX button.
You cannot use the auxiliary input jack if you replace the audio system.
QRG
TOC
Index
Home
123
2013 FituuAudio SystemuAudio Antenna
Audio Antenna
QRG
Your vehicle is equipped with a removable antenna at the rear of the roof.
1Audio Antenna
NOTICE Before using a “drive-through” car wash, remove the antenna by unscrewing it by hand. This prevents the antenna from being damaged by the car wash brushes.
Audio System Theft Protection The audio system is disabled when it is disconnected from the power source, such as when the battery is disconnected or goes dead.
■ Entering the Audio Security Code ENTER CODE appears on the display when the power is reconnected.
1. Turn on the audio system.
2. Enter the security code using the preset buttons.
Models with navigation system Touch the icon to enter the code, then touch the Done icon to set it. If you enter an incorrect digit, continue to the last digit, then try again. If you do not enter the code correctly after 10 tries, leave the system for one hour before trying again, or visit a dealer to have the system reset.
1Audio System Theft Protection
Find the audio system’s security code and serial number in your owner’s manual kit.
We recommend that you write down the serial number in this owner’s manual.
Do not store the label in your vehicle. If you lose the label, you must first retrieve the serial number, and then obtain the code.
You can find out about your serial number and security code from a dealer.
U.S. models You can register the security code at Owner Link (owners.honda.com), and find information on how to retrieve the serial number and obtain the code at radio-navicode.honda.com.
TOC
Index
Home
124
2013 FitAudio System Basic Operation
To use the audio system function, the ignition switch must be in ACCESSORY (q or ON (w.
Use the selector knob to access some audio functions.
Selector knob: Rotate left or right to scroll through the available choices. Press your selection.
to set
button: Press to go back to the previous
Button
Selector Knob
display.
1Audio System Basic Operation
These indications are used to show how to operate the selector knob. Rotate Press
to select.
to enter.
QRG
TOC
Index
Home
125
2013 Fit
1Adjusting the Sound
When the adjustment level reaches the center, you will see C in the display.
The SVC has four modes: OFF, LOW, MID, and HIGH. SVC adjusts the volume level based on the vehicle speed. As you go faster, audio volume increases. As you slow down, audio volume decreases.
uuAudio System Basic OperationuAdjusting the Sound
Adjusting the Sound
QRG
Press the to adjust the setting.
(sound) button, and rotate
Each time you press the mode switches as follows.
button, a sound
Selector Knob
Button
BASS is selectable.
Speed-sensitive Volume Compensation
TOC
Index
Home
126
2013 FitPlaying the FM/AM Radio
Buttons
Press to display and select an RDS category.
(Power) Button
Press to turn the audio system on and off.
FM/AM Button Press to select a band.
TITLE Button Press to switch the RDS name on and off.
(Seek) Buttons
● Press to change a station. ● Press and hold to search up and down the selected band for a station with a strong signal.
uuAudio System Basic OperationuPlaying the FM/AM Radio
QRG
TOC
A.SEL (Auto Select) Button Press to scan both bands and store the strongest station in each preset. To turn off auto select, press the button again. This restores the presets you originally set.
Preset Buttons (1-6) To store a station: 1. Tune to the selected station. 2. Pick a preset button and hold it
until you hear a beep.
To listen to a stored station, select a band, then press the preset button.
Selector Knob Turn to adjust the volume. Press and turn to tune the radio frequency.
SCAN Button Press to sample each of the strongest stations on the selected band for 10 seconds. To turn off scan, press the button again.
Index
Home
Continued
127
2013 FituuAudio System Basic OperationuPlaying the FM/AM Radio
■ Radio Data System (RDS) Provides text data information related to your selected RDS capable FM station.
■ RDS INFO ON Press the TITLE button while listening to an RDS capable station. RDS INFO ON appears, and the station name is displayed.
■ To find an RDS station from your selected program category
1. Press the
button to display and
RDS Category
select an RDS category.
2. Use SEEK or SCAN function to select an RDS
station.
1Playing the FM/AM Radio
The ST indicator appears on the display indicating stereo FM broadcasts. Stereo reproduction in AM is not available.
You can store six AM stations and twelve FM stations into the preset button memory. FM1 and FM2 let you store six stations each.
A.SEL function scans and stores up to six AM stations and twelve FM stations with a strong signal into the preset button memory.
If you do not like the stations auto select has stored, you can manually store your preferred frequencies.
QRG
TOC
Index
Home
128
2013 FitPlaying a CD Your audio system supports audio CDs, CD-Rs, and CD-RWs in either MP3 or WMA format. With the CD loaded, press the CD button.
CD Slot Insert a CD about halfway into the CD slot.
Selector Knob Turn to adjust the volume. Press and turn to change tracks/files or select an item, then press to set your selection.
Buttons
Press to change folders (MP3 or WMA).
(Power) Button
Press to turn the audio system on and off.
TITLE Button Press to display the CD’s text data if it was recorded. Each time you press the button, the text data information changes.
CD Button Press to play a CD.
(Seek) Buttons
Press to change tracks (files in MP3 or WMA).
uuAudio System Basic OperationuPlaying a CD
RPT (Repeat) Button ● Press to replay a track/file continuously. ● Press two times to replay all files in the
current folder.
● To turn off repeat, press and hold the
button.
RDM (Random) Button ● Press to play all tracks/files on a disc in
random order.
● Press two times to play all files in the
current folder (MP3 or WMA) in random order.
● To turn off random, press and hold the
button.
(CD Eject) Button
Press to eject a CD.
SCAN Button You will get a 10-second sampling of each song. ● Press to sample all tracks on the CD (all
files in the current folder in MP3 or WMA).
● Press two times to sample the first file in each of the main folders (MP3 or WMA).
● To turn off scan, press and hold the
button.
QRG
TOC
Index
Home
Continued
129
2013 FituuAudio System Basic OperationuPlaying a CD
■ How to Select a File from a Folder with the Selector Knob
(MP3/WMA)
1. Press
to switch the display to a folder list.
Folder Selection
2. Rotate
to select a folder.
Track Selection
3. Press
to change the display to a list of
files in that folder.
4. Rotate
to select a file, then press
1Playing a CD
NOTICE Do not use CDs with adhesive labels. The label can cause the CD to jam in the unit.
WMA files protected by digital rights management (DRM) cannot be played. The audio system displays UNSUPPORTED, then skips to the next file.
Text data appears on the display under the following circumstances: • When you select a new folder, file, or track. • When you change the audio mode to CD. • When you insert a CD.
The display shows up to 31 characters of text data. Press and hold the TITLE button to see additional characters. indicates that the text data continues. The display goes back to the previous screen if you press and hold the button again.
If you eject the CD but do not remove it from the slot, the system reloads the CD automatically after several seconds.
QRG
TOC
Index
Home
130
2013 FitPlaying an iPod® Connect the iPod® using your dock connector to the USB adapter cable, then press the AUX button.
2 USB Adapter Cable* P. 123
Buttons
to go back to the
Press previous display. Press selection.
to set your
USB Indicator Comes on when an iPod® is connected.
(Power) Button
Press to turn the audio system on and off.
TITLE Button Press to display the text data.
(Seek) Buttons
Press to change songs.
uuAudio System Basic OperationuPlaying an iPod®
AUX Button Press to select iPod® (if connected).
RDM (Random) Button ● Press to play all available files in a
selected list (playlists, artists, albums or songs) in random order.
● Press two times to play all available
albums in a selected list (playlists, artists, albums or songs) in random order.
● To turn off shuffle mode, press and
hold the button.
Selector Knob Turn to adjust the volume. Press and turn to select an item, then press to set your selection.
RPT (Repeat) Button ● Press to replay a file continuously. ● To turn off repeat, press the
button again.
QRG
TOC
Index
Home
* Not available on all models
Continued
131
2013 FituuAudio System Basic OperationuPlaying an iPod®
■ How to Select a File from the iPod® Menu
1. Press
to display the iPod® menu.
1Playing an iPod®
Available operating functions vary on models or versions. Some functions may not be available on the vehicle’s audio system.
If there is a problem, you may see an error message on the audio display.
2 iPod®/USB Flash Drive* P. 136
2. Rotate
to select a menu.
3. Press
to display the items on that menu.
4. Rotate
to select an item, then press
* Not available on all models
QRG
TOC
Index
Home
132
2013 FituuAudio System Basic OperationuPlaying a USB Flash Drive*
Playing a USB Flash Drive* Your audio system reads and plays sound files on a USB flash drive in either MP3, WMA or AAC*1 format. Connect your USB flash drive to the USB adapter cable, then press the AUX button.
2 USB Adapter Cable* P. 123
Selector Knob Turn to adjust the volume. Press and turn to select an item, then press to set your selection.
Buttons
to skip to the next
Press folder, and beginning of the previous folder.
to skip to the
(Power) Button
Press to turn the audio system on and off.
USB Indicator Comes on when a USB flash drive is connected.
(Seek) Buttons
Press to change files.
*1:Only AAC format files recorded with iTunes® are playable on this unit.
AUX Button Press to select USB flash drive (if connected).
RPT (Repeat) Button ● Press to replay a file continuously. ● Press two times to replay all files in the
current folder.
● To turn off repeat, press and hold the
button.
RDM (Random) Button ● Press to play all files in random order. ● Press two times to play all files in the
current folder in random order.
● To turn off random, press and hold the
button.
SCAN Button You will get a 10-second sampling of each file. ● Press to sample all files in the current folder. ● Press two times to sample the first file in each
of the main folders.
● To turn off scan, press and hold the button.
QRG
TOC