Download PDF Manual

clearance that allows you to travel over bumps, obstacles, and rough terrain. It also provides good visibility so you can anticipate problems earlier. Because your vehicle rides higher off the ground, it has a high center of gravity that can cause it to roll over if you make abrupt turns. Utility vehicles have a significantly higher roll over rate than other types of vehicles. To prevent rollovers or loss of control: ● Take corners at slower speeds


than you would with a passenger vehicle.


● Avoid sharp turns and abrupt


maneuvers whenever possible.


158


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


You should do the following checks and adjustments before you drive your vehicle. 1. Make sure all windows, mirrors, and outside lights are clean and unobstructed. Remove frost, snow, or ice.


2. Check that the hood is fully


closed.


3. Visually check the tires. If a tire


looks low, use a gauge to check its pressure.


4. Check that any items you may be


carrying are stored properly or fastened down securely.


5. Check the seat adjustment (see


page 83).


6. Check the adjustment of the inside and outside mirrors (see page 93).


7. Check the steering wheel adjustment (see page 74).


Preparing to Drive


8. Make sure the doors, the hatch,


and the tailgate are securely closed and locked.


9. Fasten your seat belt. Check that


your passengers have fastened their seat belts (see page 14).


10. When you start the engine, check


the gauges and indicators in the instrument panel (see page 57).


159


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


The immobilizer system protects your vehicle from theft. If an improperly coded key (or other device) is used, the engine's fuel system is disabled. For more information, see page 76.


The engine is harder to start in cold weather. Also, the thinner air found at altitudes above 8,000 feet (2,400
meters) adds to this problem.


Starting the Engine


1. Apply the parking brake. 2. In cold weather, turn off all


electrical accessories to reduce the drain on the battery.


3. Make sure the shift lever is in


Park. Press on the brake pedal.


4. Without touching the accelerator pedal, turn the ignition key to the START (III) position. Do not hold the key in the START (III) position for more than 15 seconds at a time. If the engine does not start right away, pause for at least 10 seconds before trying again.


160


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Shift Lever Position Indicators


Shifting


RELEASE BUTTON


D3 BUTTON


SHIFT LEVER


To shift from any position, press firmly on the brake pedal, push the release button, and pull the lever toward you. You cannot shift out of Park when the ignition switch is in the LOCK (0) or ACCESSORY (I) position.


These indicators on the instrument panel show which position the shift lever is in. The ‘‘D’’ indicator comes on for a few seconds when you turn the ignition switch to the ON (II) position. If it flashes while driving (in any shift position), it indicates a possible problem in the transmission. Avoid rapid acceleration, and have the transmission checked by your dealer as soon as possible.


Automatic Transmission


To shift from:


Do this:


P to R


R to P N to R D to 2
2 to 1
1 to 2
2 to D D to N N to D R to N D3 to D D to D3


Press the brake pedal, and press the shift lever release button.


Press the shift lever release button.


Move the shift lever.


Press the D3 button.


Park (P) - This position mechanically locks the transmission. Use Park whenever you are turning off or starting the engine. To shift out of Park, you must press on the brake pedal and press the release button on the shift lever. Make sure your foot is off the accelerator pedal.


CONTINUED 161


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Automatic Transmission


If you have done all of the above and still cannot move the lever out of Park, see Shift Lock Release on page 163. To avoid transmission damage, come to a complete stop before shifting into Park. You must also press the release button to shift into Park. The shift lever must be in Park before you can remove the key from the ignition switch. Reverse (R) - Press the brake pedal and press the release button to shift from Park to reverse. To shift from reverse to neutral, come to a complete stop, and then shift.


162


Neutral (N) - Use neutral if you need to restart a stalled engine, or if it is necessary to stop briefly with the engine idling. Shift to the Park position if you need to leave your vehicle for any reason. Press on the brake pedal when you are moving the shift lever from neutral to another gear.


Drive (D) - Use this position for your normal driving. The transmission automatically selects a suitable gear (1 through 5) for your speed and acceleration. You may notice the transmission shifting up at higher engine speeds when the engine is cold. This helps the engine warm up faster. Drive (D3) - To use D3, press the D3 button when the shift lever is in the ‘‘D’’ position. This position is similar to D, except only the first three gears are selected instead of all five. Use D3 when towing a trailer in hilly terrain, or to provide engine braking when going down a steep hill. D3 can also keep the transmission from cycling between third and fourth gears in stop-and-go driving.


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Second (2) - This position locks the transmission in second gear. It does not downshift to first gear when you come to a stop. Use second gear: ● For more power when climbing. ● To increase engine braking when


going down steep hills.


● For starting out on a slippery


surface or in deep snow.


● To help reduce wheel spin. ● When driving downhill with a


trailer.


First (1) - This position locks the transmission in first gear. By upshifting and downshifting through 1, 2, D3, and D, you can operate the transmission much like a manual transmission without a clutch pedal. Engine Speed Limiter If you exceed the maximum speed for the gear you are in, the engine speed will enter into the tachometer's red zone. If this occurs, you may feel the engine cut in and out. This is caused by a limiter in the engine's computer controls. The engine will run normally when you reduce the rpm below the red zone.


Automatic Transmission


Shift Lock Release This allows you to move the shift lever out of Park if the normal method of pushing on the brake pedal and pressing the release button does not work. 1. Set the parking brake. 2. Remove the key from the ignition


switch.


CONTINUED 163


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Automatic Transmission


COVER


3. Put a cloth on the edge of the shift lock release slot cover next to the shift lever to prevent scratches. Using a flat-tip screwdriver, carefully pry on the edge of the cover to remove it.


SHIFT LOCK RELEASE SLOT


4. Insert the key in the shift lock


release slot.


5. Push down on the key while you


press the release button on the shift lever and move the shift lever out of Park to neutral.


164


6. Remove the key from the shift lock


release slot, then reinstall the cover. Make sure the notch on the cover is on the right side. Insert the key into the ignition switch, press the brake pedal, and restart the engine.


If you need to use the shift lock release, it means your vehicle is developing a problem. Have it checked by your dealer.


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Always use the parking brake when you park your vehicle. Make sure the parking brake is set firmly, or your vehicle may roll if it is parked on an incline. Set the parking brake before you put the transmission in Park. This keeps the vehicle from moving and putting pressure on the parking mechanism in the transmission.


Parking Tips ● Make sure the windows are


closed.


● Turn off the lights. ● Place any packages, valuables, etc. in the cargo area or take them with you.


● Lock the doors and the hatch with


the key.


● Never park over dry leaves, tall


grass, or other flammable materials. The hot three way catalytic converter could cause these materials to catch on fire.


Parking


● If the vehicle is facing uphill, turn


the front wheels away from the curb.


● If the vehicle is facing downhill, turn the front wheels toward the curb.


● Make sure the parking brake is


fully released before driving away. Driving with the parking brake partially set can overheat or damage the rear brakes.


165


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Constant application of the brakes when going down a long hill builds up heat and reduces their effectiveness. Use the engine to assist the brakes by taking your foot off the accelerator and downshifting to a lower gear. Check your brakes after driving through deep water. Apply the brakes moderately to see if they feel normal. If not, apply them gently and frequently until they do. Be extra cautious and alert in your driving.


Braking System Design The hydraulic system that operates the brakes has two separate circuits. Each circuit works diagonally across the vehicle (the left-front brake is connected with the right-rear brake, etc.). If one circuit should develop a problem, you will still have braking at two wheels.


Braking System


Your vehicle is equipped with disc brakes at all four wheels. A power assist helps reduce the effort needed on the brake pedal. The emergency brake assist system increases the stopping force when you depress the brake pedal hard in an emergency situation. The anti-lock brake system (ABS) helps you retain steering control when braking very hard. Resting your foot on the pedal keeps the brakes applied lightly, builds up heat, reduces their effectiveness and reduces brake pad life. In addition, fuel economy can be reduced. It also keeps your brake lights on all the time, confusing drivers behind you.


166


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Brake Pad Wear Indicators If the brake pads need replacing, you will hear a distinctive, metallic screeching sound when you apply the brake pedal. If you do not have the brake pads replaced, they will screech all the time. It is normal for the brakes to occasionally squeal or squeak when you apply them.


Braking System, Anti-lock Brakes (ABS)


Anti-lock Brakes (ABS) The anti-lock brake system (ABS) helps prevent the wheels from locking up, and helps you retain steering control by pumping the brakes rapidly, much faster than a person can do it. The electronic brake distribution (EBD) system, which is part of the ABS, also balances the front-to-rear braking distribution according to vehicle loading. Youshouldneverpumpthebrakepedal. Let the ABS work for you by always keeping firm, steady pressure on the brake pedal. This is sometimes referred to as ‘‘stomp and steer.’’


You will feel a pulsation in the brake pedal when the ABS activates, and you may hear some noise. This is normal: it is the ABS rapidly pumping the brakes. On dry pavement, you will need to press on the brake pedal very hard before the ABS activates. However, you may feel the ABS activate immediately if you are trying to stop on snow or ice.


CONTINUED 167


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Test your brakes as instructed on page 237. If the brakes feel normal, drive slowly and have your vehicle repaired by your dealer as soon as possible. Avoid sudden hard braking which could cause the rear wheels to lock up and possibly lead to a loss of control. Important Safety Reminders ABS does not reduce the time or distance it takes to stop the vehicle. It only helps with steering control during braking.


ABS will not prevent a skid that results from changing direction abruptly, such as trying to take a corner too fast or making a sudden lane change. Always drive at a safe speed for the road and weather conditions. ABS cannot prevent a loss of stability. Always steer moderately when you are braking hard. Severe or sharp steering wheel movement can still cause your vehicle to veer into oncoming traffic or off the road. A vehicle with ABS may require a longer distance to stop on loose or uneven surfaces, such as gravel or snow, than a vehicle without anti- lock.


Anti-lock Brakes (ABS)


ABS Indicator


If this indicator comes on, the anti- lock function of the braking system has shut down. The brakes still work like a conventional system, but without anti-lock. You should have your dealer inspect your vehicle as soon as possible. If the indicator comes on while driving, test the brakes as instructed on page 237. If the ABS indicator and the brake system indicator come on together, and the parking brake is fully released, the EBD system may also be shut down.


168


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Your vehicle is equipped with a tire pressure monitoring system (TPMS) that turns on every time you start the engine and monitors the pressure in your tires while driving. Each tire has its own pressure sensor (not including the spare tire). If the air pressure of a tire becomes significantly low, the sensor in that tire immediately sends a signal that causes the low tire pressure indicator to come on.


Tire Pressure Monitoring System (TPMS)


Low Tire Pressure Indicator


When the low tire pressure indicator is on, one or more of your tires is significantly underinflated. You should stop and check your tires as soon as possible, and inflate them to the proper pressure as indicated on the vehicle's tire information placard. If you think you can safely drive a short distance to a service station, proceed slowly, and inflate the tire to the recommended pressure shown on the driver's doorjamb. If the tire is flat, or if the tire pressure is too low to continue driving, replace the tire with the compact spare tire (see page 222).


If you cannot make the low tire pressure indicator go out after inflating the tires to the specified values, have your dealer check the system as soon as possible. Driving on a significantly underinflated tire causes the tire to overheat and can lead to tire failure. Underinflation also reduces fuel efficiency and tire tread life, and may affect the vehicle's handling and stopping ability. Because tire pressure varies by temperature and other conditions, the low tire pressure indicator may come on unexpectedly.


CONTINUED 169


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Tire Pressure Monitoring System (TPMS)


For example, if you check and fill your tires in a warm area, then drive in extremely cold weather, the tire pressure will be lower than measured and could be underinflated and cause the low tire pressure indicator to come on. Or, if you check and adjust your tire pressure in cooler conditions, and drive into extremely hot conditions, the tire may become overinflated. However, the low tire pressure indicator will not come on if the tires are overinflated. Refer to page 212 for tire inflation guidelines. Although your tire pressure is monitored, you must manually check the tire pressures monthly. Each tire, including the spare, should be checked monthly when cold and set to the recommended inflation pressure as specified in the vehicle placard and this owner's manual (see page 252).


170


Tire Pressure Monitoring System (TPMS) Indicator This indicator comes on and stays on if there is a problem with the tire pressure monitoring system. If this happens, the system will shut off and no longer monitor tire pressures. Have the system checked by your dealer as soon as possible. When you restart the vehicle with the compact spare tire, the TPMS indicator may also come on and stay on after driving several miles (kilometers).


Changing a Tire with TPMS If you have a flat tire, the low tire pressure indicator will come on. Replace the flat tire with the compact spare tire (see page 222). Each wheel (except the compact spare tire wheel) is equipped with a tire pressure sensor. You must use TPMS specific wheels. It is recommended that you always have your tires serviced by your dealer or qualified technician. After you replace the flat tire with the compact spare tire, the low tire pressure indicator stays on. This is normal; the system is not monitoring the spare tire pressure. Manually check the spare tire pressure to be sure it is correct. After several miles (kilometers) driving with the compact spare tire, the TPMS indicator comes on and the low tire pressure indicator goes off.


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Tire Pressure Monitoring System (TPMS)


The low tire pressure indicator or the TPMS indicator will go off, after several miles (kilometers) driving, when you replace the spare tire with the specified regular tire equipped with the tire pressure monitor sensor. Never use a puncture-repairing agent in a flat tire. If used, you will have to replace the tire pressure sensor. Have the flat tire repaired by your dealer as soon as possible.


AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation. Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser's authoritytooperatetheequipment.


171


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Vehicle Stability Assist (VSA®), aka Electronic Stability Control (ESC), System


If the indicator does not come on when the ignition switch is turned to the ON (II) position, there may be a problem with the VSA system. Have your dealer inspect your vehicle as soon as possible. Without VSA, your vehicle will have normal braking and cornering ability, but it will not have VSA traction and stability enhancement.


The vehicle stability assist (VSA) system helps to stabilize the vehicle during cornering if the vehicle turns more or less than desired. It also assists you in maintaining traction while accelerating on loose or slippery road surfaces. It does this by regulating the engine's output and by selectively applying the brakes. When VSA activates, you may notice that the engine does not respond to the accelerator in the same way it does at other times. You will also see the VSA system indicator blink. The VSA system cannot enhance the vehicle's driving stability in all situations and does not control your vehicle's entire braking system. It is still your responsibility to drive and corner at reasonable speeds and to leave a sufficient margin of safety.


VSA OFF Indicator


When VSA is off, the VSA OFF indicator comes on as a reminder.


Vehicle Stability Assist (VSA) System Indicator


When VSA activates, you will see the VSA system indicator blink. If this indicator comes on while driving, pull to the side of the road when it is safe, and turn off the engine. Reset the system by restarting the engine. If the VSA system indicator stays on or comes back on while driving, have the VSA system inspected by your dealer. NOTE: The main function of the VSA system is generally known as Electronic Stability Control (ESC). The system also includes a traction control function.


172


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Vehicle Stability Assist (VSA®), aka Electronic Stability Control (ESC), System


VSA OFF Switch In certain unusual conditions when your vehicle gets stuck in shallow mud or fresh snow, it may be easier to free it with the VSA temporarily switched off. When the VSA system is off, the traction control system is also off. You should only attempt to free your vehicle with the VSA off if you are not able to free it when the VSA is on. Immediately after freeing your vehicle, be sure to switch the VSA on again. We do not recommend driving your vehicle with the VSA and traction control systems switched off.


VSA OFF SWITCH


This switch is under the driver's side vent. To turn the VSA system on and off, press and hold it until you hear a beep. When VSA is off, the VSA OFF indicator comes on as a reminder. Press and hold the switch again. It turns the system back on. VSA is turned on every time you start the engine, even if you turned it off the last time you drove the vehicle.


VSA and Tire Sizes Driving with varying tire or wheel sizes may cause the VSA to malfunction. When replacing tires, make sure they are the same size and type as your original tires (see page 216). If you install winter tires, make sure they are the same size as those that were originally supplied with your vehicle. Exercise the same caution during winter driving as you would if your vehicle was not equipped with VSA.


173


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Towing a Trailer


Your vehicle has been designed primarily to carry passengers and their cargo. You can also use it to tow a trailer if you carefully observe the load limits, use the proper equipment, and follow the guidelines in this section. Break-InPeriod Avoid towing a trailer during your vehicle's first 600 miles (1,000 km) (see page 142). Be sure to read the Off-Highway Driving Guidelines section on page 180 if you plan to tow off paved surfaces.


174


Load Limits


Exceeding any load limit or improperly loading your vehicle and trailer can cause a crash in which you can be seriously hurt or killed.


Check the loading of your vehicle and trailer carefully before starting to drive.


Total Trailer Weight: The maximum allowable weight of the trailer and everything in or on it must not exceed 1,500 lbs (680 kg). Towing a trailer that is too heavy can seriously affect your vehicle's handling and performance. It can also damage the engine and drivetrain.


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


To achieve a proper tongue load, start by loading 60% of the load toward the front of the trailer and 40% toward the rear, then re-adjust the load as needed. ● Gross Vehicle Weight Rating


(GVWR): The maximum allowable weight of the vehicle, all occupants, all accessories, all cargo, and the tongue load is:


4,450 lbs (2,020 kg)


● Gross Axle Weight Rating


(GAWR): The maximum allowable weight of the vehicle axles is:


2,300 lbs (1,045 kg) on the front axle 2,205 lbs (1,000 kg) on the rear axle


Towing a Trailer


Checking Loads The best way to confirm that all loads are within limits is to check them at a public scale. For public scales in your area, check your local phone book, or contact your trailer dealer or rental agency for assistance. If you cannot get to a public scale, you can estimate the total trailer weight by adding the weight of your trailer (as quoted by the manufacturer) with everything in or on the trailer. If you normally pull the same load each time you tow a trailer, you can use a suitable scale or a special tongue load gauge to check the tongue load the first time you set up a towing combination (a fully loaded vehicle and trailer), then recheck the tongue load whenever the conditions change.


CONTINUED 175


Tongue Load: The weight that the tongue of a fully-loaded trailer puts on the hitch should be approximately 10% of the total trailer weight. Too much tongue load reduces front-tire traction and steering control. Too little tongue load can make the trailer unstable and cause it to sway.


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Towing a Trailer


Towing Equipment and Accessories Towing can require a variety of equipment, depending on the size of your trailer, how it will be used, how much load you are towing, and where you tow. To ensure the highest quality equipment, purchase Honda equipment whenever possible. Discuss your needs with your trailer sales or rental agency, and follow the guidelines in the rest of this section. Also make sure that all equipment is properly installed and that it meets federal, state, provincial, territorial and local regulations.


176


Hitches Any hitch used on your vehicle must be properly bolted to the underbody. SafetyChains Always use safety chains when you tow a trailer. Make sure the chains are secured to the trailer and hitch, and that they cross under the tongue and can catch the trailer if it becomes unhitched. Leave enough slack to allow the trailer to turn corners easily, but do not let the chains drag on the ground.


TrailerBrakes Honda recommends that any trailer with a total weight of 1,000 lbs (450
kg) or more has its own brake. There are two common types of trailer brakes; surge and electric. Surge brakes are common for boat trailers, since the brakes will get wet. If you choose electric brakes, be sure they are electronically actuated. Do not attempt to tap into your vehicle's hydraulic system. No matter how successful it may seem, any attempt to attach trailer brakes to your vehicle's hydraulic system will lower braking effectiveness and create a potential hazard. See your trailer dealer or rental agency for more information on installing electric brakes.


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


TrailerLights Trailer lights and equipment must comply with federal, state, provincial, territorial, and local regulations. Check with your local trailer dealer or rental agency for the requirements in the area where you plan to tow, and use only equipment designed for your vehicle. Since lighting and wiring vary by trailer type and brand, you should have a qualified technician install a suitable connector between the vehicle and the trailer. Improper equipment or installation can cause damage to your vehicle's electrical system and affect your vehicle warranty.


Towing a Trailer


Ask your trailer sales or rental agency if any other items are recommended or required for your towing situation.


AdditionalTowingEquipment Many states require special outside mirrors when towing a trailer. Even if they don't, you should install special mirrors if you cannot clearly see behind you, or if the trailer creates a blind spot.


CONTINUED 177


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Towing a Trailer


Pre-Tow Checklist When preparing to tow, and before driving away, be sure to check the following: ● The vehicle has been properly serviced, and the tires, brakes, suspension, cooling system, and lights are in good operating condition.


● The trailer has been properly


serviced and is in good condition.


● All weights and loads are within limits (see pages 174 and 175).


● The hitch, safety chains, and any


other attachments are secure.


● All items in or on the trailer are


properly secured and cannot shift while you drive.


178


● Your vehicle tires and spare are properly inflated (see page 212), and the trailer tires and spare are inflated as recommended by the trailer maker.


Driving Safely With a Trailer The added weight, length, and height of a trailer will affect your vehicle's handling and performance, so driving with a trailer requires some special driving skills and techniques. For your safety and the safety of others, take time to practice driving maneuvers before heading for the open road, and follow the guidelines below. TowingSpeedsandGears Drive slower than normal in all driving situations, and obey posted speed limits for vehicles with trailers. Use the D position when towing a trailer on level roads. D3 is the proper shift lever position to use when towing a trailer in hilly terrain. (See ‘‘DrivingonHills’’ on the next page for additional gear information.)


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Towing a Trailer


MakingTurnsandBraking Make turns more slowly and wider than normal. The trailer tracks a smaller arc than your vehicle, and it can hit or run over something the vehicle misses. Allow more time and distance for braking. Do not brake or turn suddenly as this could cause the trailer to jackknife or turn over. DrivingonHills When climbing hills, closely watch your temperature gauge. If it nears the red (Hot) mark, turn the air conditioning off, reduce speed and, if necessary, pull to the side of the road to let the engine cool. If the automatic transmission shifts frequently while going up a hill, shift to D3.


If you must stop when facing uphill, use the foot brake or parking brake. Do not try to hold the vehicle in place by pressing on the accelerator, as this can cause the automatic transmission to overheat. When driving down hills, reduce your speed, and shift down to second gear. Do not ‘‘ride’’ the brakes, and remember, it will take longer to slow down and stop when towing a trailer. HandlingCrosswindsandBuffeting Crosswinds and air turbulence caused by passing trucks can disrupt your steering and cause the trailer to sway. When being passed by a large vehicle, keep a constant speed, and steer straight ahead. Do not try to make quick steering or braking corrections.


BackingUp Always drive slowly and have someone guide you when backing up. Grip the bottomof the steering wheel, then turn the wheel to the left to get the trailer to move to the left, and turn the wheel right to move the trailer to the right. Parking Follow all normal precautions when parking, including firmly setting the parking brake and putting the transmission in Park. Also, place wheel chocks at each of the trailer's tires. Towing Your Vehicle Your vehicle is not designed to be towed behind a motor home. If your vehicle needs to be towed in an emergency, see page 244.


179


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Improperly operating this vehicle on or off pavement can cause a crash or rollover in which you and your passengers could be seriously injured or killed. ● Follow all instructions and guidelines in this owner's manual.


● Keep your speed low, and


don't drive faster than conditions permit.


Important Safety Precautions To avoid loss of control or rollover, be sure to follow all precautions and recommendations. ● Be sure to store cargo properly, and do not exceed your vehicle cargo load limits (see pages 152
and 174).


● Wherever you drive, make sure you and your passengers always wear seat belts.


● Keep your speed low, and never go


faster than the conditions allow.


● It's up to you to continually assess the situation and drive within the limits.


Off-Highway Driving Guidelines


General Information Your vehicle has been designed primarily for use on pavement. But its higher ground clearance allows you to occasionally travel on unpaved roads, such as campgrounds, picnic sites, and similar locations. It is not designed for trail-blazing, mountain climbing, or other challenging off- road activities. If you decide to drive on unpaved roads, you will find that it requires somewhat different driving skills. Your vehicle will also handle somewhat differently than it does on pavement. So be sure to read this owner's manual, pay special attention to the precautions and tips in this section, and get acquainted with your vehicle before you leave the pavement.


180


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Off-Highway Driving Guidelines


Accelerating and Braking For better traction on all surfaces, accelerate slowly and gradually build up speed. If you try to start too fast on wet soil, mud, snow, or ice, you might not have enough traction to get underway, and you may dig yourself a hole. Starting with the shift lever in second (2) gear will help you have a smoother start on snow or ice. Keep in mind that you will usually need more time and distance to brake to a stop on unpaved surfaces. Avoid hard braking. Do not ‘‘pump’’ the brakes; let the anti-lock braking system pump them for you.


Check Out Your Vehicle Before you leave the pavement, be sure to do all scheduled maintenance and service, and inspect your vehicle for any problems. Pay special attention to the condition of the tires, and check the tire pressures. After you return to the pavement, carefully inspect your vehicle to make sure there is no damage that could make driving it unsafe. Recheck the condition of the tires and the tire pressures. Remember The route presents limits (too steep or bumpy roads). You have limits (driving skill and comfort). And your vehicle has limits (traction, stability, and power). Driving off-highway can be hazardous if you fail to recognize limits and take the proper precautions.


Avoiding Obstacles Debris on the road can damage your suspension or other components. Because your vehicle has a high center of gravity, driving over a large obstacle, or allowing a wheel to drop into a deep hole can cause your vehicle to tip or roll over. Driving on Slopes If you can't clearly see all conditions or obstacles on a slope, walk the slope before you drive on it. If you have any doubt whether or not you can safely drive on the slope, don't do it. Find another route. If you are driving up a hill and find that you cannot continue, donottryto turnaround.Your vehicle could roll over. Slowly back down the hill, following the same route you took up the hill.


CONTINUED 181


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Off-Highway Driving Guidelines


Crossing a Stream Avoid driving through deep water. If you encounter water in your route (a small stream or large puddle, for example), evaluate it carefully before going ahead. Make sure it is shallow, flowing slowly, and has firm ground underneath. If you are not sure of the depth or the ground, turn around and find another route. Driving through deep water can also damage your vehicle. The water can get into the transmission and differential, diluting the lubricant and causing an eventual failure. It can also wash the grease out of the wheel bearings.


If You Get Stuck Avoid driving on soft sand, deep mud, or other surfaces where you could get stuck. If you do happen to get stuck because of inclement weather or other conditions, choose a safe and appropriate course of action. You should never use a jack to try getting unstuck. A jack only works on firm, level ground. Also, your vehicle could easily slip off the jack and hurt you or someone else.


4-WheelDriveVehicles If you spin the wheels excessively trying to get unstuck, you may overheat the components of the 4- wheel drive system. If this happens, the 4-wheel drive system shuts off and only the front wheels receive power. At this point, you must stop and allow everything to cool down. The 4-wheel drive system will work again after its temperature drops. If you slip the clutch for a long time while trying to get unstuck, you may overheat and damage it.


182


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Maintenance, replacement, or repair of emissions control devices and systems may be done by any automotive repair establishment or individual using parts that are ‘‘certified’’ to EPA standards.


This section explains why it is important to keep your vehicle well maintained and how to follow basic maintenance safety precautions.


This section also includes instructions on how to read the Maintenance Minder messages on the information display, and instructions for simple maintenance tasks you may want to take care of yourself. If you have the skills and tools to perform more complex maintenance tasks on your vehicle, you may want to purchase the service manual. See page 267 for information on how to obtain a copy, or see your dealer.


Maintenance


Maintenance Safety..................... 184
Maintenance MinderTM ............... 185
Fluid Locations ........................... 192
Adding Engine Oil ...................... 193
Changing the Engine Oil and


Filter ....................................... 194
Engine Coolant ........................... 196
Windshield Washers................... 197
Automatic Transmission Fluid .... 198
Brake Fluid................................. 199
Power Steering Fluid .................. 200
Cleaning the Body Panels ........... 201
Lights.......................................... 201
Cleaning the Seat Belts ............... 209
Floor Mats .................................. 209
Dust and Pollen Filter ................. 210
Wiper Blades .............................. 210
Wheels........................................ 212
Tires ........................................... 212
Checking the Battery .................. 218
Vehicle Storage........................... 219


183


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Maintenance Safety


All service items not detailed in this section should be performed by a certified technician or other qualified mechanic. Important Safety Precautions To eliminate potential hazards, read the instructions before you begin, and make sure you have the tools and skills required. ● Make sure your vehicle is parked on level ground, the parking brake is set, and the engine is off.


● To clean parts, use a commercially


available degreaser or parts cleaner, not gasoline.


● To reduce the possibility of fire or explosion, keep cigarettes, sparks, and flames away from the battery and all fuel-related parts.


184


● Wear eye protection and protective


clothing when working with the battery or compressed air.


● Burns from hot parts. Let the engine and exhaust system cool down before touching any parts.


Improperly maintaining this vehicle, or failing to correct a problem before driving can cause a crash in which you can be seriously hurt or killed.


Always follow the inspection and maintenance recommendations and schedules in this owner's manual.


Potential Vehicle Hazards ● Carbon Monoxide poison from engine exhaust. Be sure there is adequate ventilation whenever you operate the engine.


● Injury from moving parts. Do not run the engine unless instructed to do so.


Failure to properly follow maintenance instructions and precautions can cause you to be seriously hurt or killed.


Always follow the procedures and precautions in this owner's manual.


Some of the most important safety precautions are given here. However, we cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task.


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Your vehicle displays engine oil life and maintenance service items on the information display to show you when you should have your dealer do engine oil replacement and indicated maintenance service. Based on the engine operating conditions and accumulated engine revolutions, the onboard computer in your vehicle calculates the remaining engine oil life and displays it as a percentage.


Maintenance MinderTM


Engine Oil Life Display


SELECT/RESET KNOB


The remaining engine oil life is shown on the display according to this table:


ENGINE OIL LIFE INDICATOR


To see the current engine oil life, turn the ignition switch to the ON (II) position, then press and release the select/reset knob repeatedly until the engine oil life indicator appears.


Calculated Engine


Oil Life (%) 100% - 91% 90% - 81% 80% - 71% 70% - 61% 60% - 51% 50% - 41% 40% - 31% 30% - 21% 20% - 16% 15% - 11% 10% - 6% 5% - 1%


0%


Displayed


Engine Oil Life (%)


100% 90% 80% 70% 60% 50% 40% 30% 20% 15% 10% 5% 0%


CONTINUED 185


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Maintenance MinderTM


MAINTENANCE MINDER INDICATOR


MAINTENANCE ITEM CODE(S)


ENGINE OIL LIFE INDICATOR


If the remaining engine oil life is 15
to 6 percent, you will see the engine oil life indicator every time you turn the ignition switch to the ON (II) position. The Maintenance Minder indicator will also come on, and the maintenance item code(s) for other scheduled maintenance items needing service will be displayed above the ‘‘OIL LIFE’’ message.


186


The 15 and 10 percent oil life indicator reminds you that the time is coming soon to take your vehicle in for the required maintenance.


When the remaining engine oil life is 5 to 1 percent, you will see a ‘‘SERVICE’’ message along with the same maintenance item code(s), every time you turn the ignition switch to the ON (II) position.


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


The maintenance item code or codes indicate the main and sub items required at the time of the oil change (see page 188). You can switch the information display from the engine oil life display to the odometer or the trip meter. Press and release the select/ reset knob on the instrument panel. When the engine oil life is 15 to 1
percent, the Maintenance Minder indicator ( you turn the ignition switch to the ON (II) position, then it goes out if you switch the information display. When you see this message, have the indicated maintenance performed by your dealer as soon as possible.


) comes on every time


Maintenance MinderTM


NEGATIVE DISTANCE TRAVELED


When the remaining engine oil life is 0 percent, the engine oil life indicator will blink. The display comes on every time you turn the ignition switch to the ON (II) position. The Maintenance Minder indicator ( also comes on and remains on in the instrument panel. When you see this message, immediately have the indicated maintenance done by your dealer.


If you do not perform the indicated maintenance, negative distance traveled is displayed and begins to blink after the vehicle has been driven 10 miles or more. Negative distance traveled means your vehicle has passed the maintenance required point. Immediately have the indicated maintenance done by your dealer.


CONTINUED 187


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Maintenance MinderTM


To change the information display from the engine oil life display to the odometer or the trip meter, press and release the select/reset knob. When the engine oil life is 0 percent or negative distance traveled, the Maintenance Minder indicator ( remains on even if you change the information display. Immediately have the service performed, and make sure to reset the display as described as follows.


188


Maintenance Main Items and Sub Items


MAINTENANCE MAIN ITEM


MAINTENANCE SUB ITEM(S)


All maintenance items displayed on the information display are in code. For an explanation of these maintenance codes, see page 191.


Resetting the Engine Oil Life Display Your dealer will reset the display after completing the required maintenance service. You will see ‘‘OIL LIFE 100%’’ on the information display the next time you turn the ignition switch to the ON (II) position. If maintenance service is done by someone other than your dealer, reset the Maintenance Minder as follows: 1. Turn the ignition switch to the ON


(II) position.


2. Press the select/reset knob


repeatedly until the engine oil life is displayed.


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


3. Press the select/reset knob for


about 10 seconds. The engine oil life and the maintenance item code(s) will blink.


4. Press the select/reset knob for


another 5 seconds. The maintenance item code(s) will disappear, and the engine oil life will reset to ‘‘100.’’


Maintenance MinderTM


Important Maintenance Precautions If you have the required service done but do not reset the display, or reset the display without doing the service, the system will not show the proper maintenance intervals. This can lead to serious mechanical problems because you will no longer have an accurate record of when maintenance is needed. Your authorized Honda dealer knows your vehicle best and can provide competent, efficient service.


CONTINUED 189


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Maintenance MinderTM


However, service at a dealer is not mandatory to keep your warranties in effect. Maintenance may be done by any qualified service facility or person who is skilled in this type of automotive service. Make sure to have the service facility or person reset the display as previously described. Keep all receipts as proof of completion, and have the person who does the work fill out your Honda Service History. Check your warranty booklet for more information. We recommend using Honda parts and fluids whenever you have maintenance done. These are manufactured to the same high quality standards as the original components, so you can be confident of their performance and durability.


190


According to state and federal regulations, failure to perform maintenance on the items marked with # will not void your emissions warranties. However, all maintenance services should be performed in accordance with the intervals indicated by the information display. Owner's Maintenance Checks You should check the following items at the specified intervals. If you are unsure of how to perform any check, turn to the appropriate page listed. ● Engine oil level - Check every


time you fill the fuel tank. See page 145.


● Engine coolant level - Check the


radiator reserve tank every time you fill the fuel tank. See page 145. ● Automatic transmission - Check the fluid level monthly. See page 198.


● Brakes - Check the fluid level


monthly. See page 199.


● Tires - Check the tire pressure monthly. Examine the tread for wear and foreign objects. See page 212.


● Lights - Check the operation of


the headlights, parking lights, taillights, high-mount brake light, and license plate lights monthly. See page 201.


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Symbol


● Replace engine oilꭧ1
● Replace engine oilꭧ1 and oil filter ● Inspect front and rear brakes ● Check parking brake adjustment ● Inspect these items:


● Tie rod ends, steering gear box, and boots ● Suspension components ● Driveshaft boots ● Brake hoses and lines (including ABS/VSA) ● All fluid levels and condition of fluids ● Exhaust system# ● Fuel lines and connections#


ꭧ1:


If the message ‘‘SERVICE’’ does not appear more than 12 months after the display is reset, change the engine oil every year.


#: See information on maintenance and emissions warranty on page 190.


NOTE: ● Independent of the maintenance message in the information display,


replace the brake fluid every 3 years.


● Inspect idle speed every 160,000 miles (256,000 km). ● Adjust the valves during services A, B, 1, 2, or 3 if they are noisy.


Maintenance Main Items


Symbol


Maintenance Sub Items


Maintenance MinderTM


● Rotate tires ● Replace air cleaner element


If you drive in dusty conditions, replace every 15,000 miles (24,000 km).


● Replace dust and pollen filter


If you drive primarily in urban areas that have high concentrations of soot in the air from industry and from diesel-powered vehicles, replace every 15,000 miles (24,000 km).


● Inspect drive belt ● Replace transmission fluid


Driving in mountainous areas at very low vehicle speeds or trailer towing results in higher transmission and transfer temperatures. This requires transmission and transfer fluid changes more frequently than recommended by the Maintenance Minder. If you regularly drive your vehicle under these conditions, have the transmission and transfer fluid changed at 60,000 miles (100,000 km), then every 30,000 miles (48,000 km).


● Replace spark plugs ● Inspect valve clearance ● Replace engine coolant ● Replace rear differential fluid (4WD model only)


191


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Fluid Locations


ENGINE OIL FILL CAP


ENGINE OIL DIPSTICK (Orange tab)


POWER STEERING FLUID (Red cap)


WASHER FLUID (Blue cap)


ENGINE COOLANT RESERVOIR


RADIATOR CAP


192


BRAKE FLUID (Gray cap)


AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow loop)


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


ENGINE OIL FILL CAP


Recommended Engine Oil Oil is a major contributor to your engine's performance and longevity. Always use a premium-grade 5W-20
detergent oil displaying the API Certification Seal. This seal indicates the oil is energy conserving, and that it meets the American Petroleum Institute's latest requirements.


Unscrew and remove the engine oil fill cap on top of the valve cover. Pour in the oil slowly and carefully so you do not spill. Clean up any spills immediately. Spilled oil could damage components in the engine compartment. Reinstall the engine oil fill cap, and tighten it securely. Wait a few minutes, and recheck the oil level on the engine oil dipstick. Do not fill above the upper mark; you could damage the engine.


API CERTIFICATION SEAL


Adding Engine Oil


Honda motor oil is the preferred 5W-20 lubricant for your vehicle. It is highly recommended that you use Honda motor oil in your vehicle for optimum engine protection. Make sure the API Certification Seal says ‘‘For Gasoline Engines.’’ The oil viscosity or weight is provided on the container's label. 5W-20 oil is formulated for year- round protection of your vehicle to improve cold weather starting and fuel economy.


Ambient Temperature


CONTINUED 193


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Adding Engine Oil, Changing the Engine Oil and Filter


Synthetic Oil You may use a synthetic motor oil if it meets the same requirements given for a conventional motor oil, it displays the API Certification Seal, and it is the proper weight. You must follow the oil and filter change intervals shown on the Maintenance Minder display. Engine Oil Additives Your vehicle does not require any oil additives. Additives may adversely affect the engine or transmission performance and durability.


Changing the Engine Oil and Filter Always change the oil and filter according to the maintenance messages shown on the information display. The oil and filter collect contaminants that can damage your engine if they are not removed regularly. Changing the oil and filter requires special tools and access from underneath the vehicle. The vehicle should be raised on a service station- type hydraulic lift for this service. Unless you have the knowledge and proper equipment, you should have this maintenance done by a skilled technician.


WASHER


OIL DRAIN BOLT


1. Run the engine until it reaches normal operating temperature, then shut it off.


2. Open the hood, and remove the engine oil fill cap. Remove the oil drain bolt and washer from the bottom of the engine. Drain the oil into an appropriate container.


194


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


OIL FILTER


3. Remove the oil filter and let the


remaining oil drain. A special wrench (available from your dealer) is required. Make sure the oil filter gasket is not stuck to the engine block. If it is, remove it before installing a new oil filter.


Changing the Engine Oil and Filter


4. Install a new oil filter according to the instructions that come with it. Make sure to clean off any dirt and dust on the connecting surface of a new oil filter.


5. Put a new washer on the drain


bolt, then reinstall the drain bolt. Tighten the drain bolt to: 33 lbf·ft (45 N·m, 4.5 kgf·m)


6. Refill the engine with the


recommended oil.


Engine oil change capacity (including filter): 4.4 US qt (4.2 L)


9. Turn off the engine and let it sit for several minutes, then check the oil level on the dipstick. If necessary, add more oil.


Improper disposal of engine oil can be harmful to the environment. If you change your own oil, please dispose of the used oil properly. Put it in a sealed container, and take it to a recycling center. Do not discard it in a trash bin or dump it on the ground.


7. Replace the engine oil fill cap. Start


the engine. The oil pressure indicator should go out within 5
seconds. If it does not, turn off the engine, and check your work. 8. Let the engine run for several


minutes, then check the drain bolt and oil filter for leaks.


195


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Engine Coolant


Adding Engine Coolant


RESERVE TANK


If the coolant level in the reserve tank is at or below the MIN line, add coolant to bring it up to the MAX line. Inspect the cooling system for leaks.


196


Always use Honda Long-life Anti- freeze/Coolant Type 2. This coolant is pre-mixed with 50 percent antifreeze and 50 percent distilled water. Never add straight antifreeze or plain water. If Honda antifreeze/coolant is not available, you may use another major-brand non-silicate coolant as a temporary replacement. Make sure it is a high-quality coolant recommended for aluminum engines. Continued use of any non- Honda coolant can result in corrosion, causing the cooling system to malfunction or fail. Have the cooling system flushed and refilled with Honda antifreeze/ coolant as soon as possible.


If the reserve tank is completely empty, you should also check the coolant level in the radiator.


Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.


Always let the engine and radiator cool down before removing the radiator cap.


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Engine Coolant, Windshield Washers


4. The coolant level should be up to


the base of the filler neck. Add coolant if it is low. Pour the coolant slowly and carefully so you do not spill any. Clean up any spill immediately; it could damage components in the engine compartment.


5. Put the radiator cap back on and


tighten it fully.


6. Pour coolant into the reserve tank. Fill it to halfway between the MAX and MIN marks. Put the cap back on the reserve tank.


Do not add any rust inhibitors or other additives to your vehicle's cooling system. They may not be compatible with the coolant or engine components.


Windshield Washers


LEVEL GAUGE


Check the fluid level in the windshield washer reservoir at least monthly during normal use. Check the reservoir's fluid level by removing the cap and looking at the level gauge attached to the cap.


CONTINUED 197


RADIATOR CAP 1. Make sure the engine and radiator


are cool.


2. Relieve any pressure in the cooling system by turning the radiator cap counterclockwise, without pressing down.


3. Remove the radiator cap by pushing down and turning counterclockwise.


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


Windshield Washers, Automatic Transmission Fluid


Fill the reservoir with a good-quality windshield washer fluid. This increases the cleaning capability and prevents freezing in cold weather. When you refill the reservoir, clean the edges of the windshield wiper blades with windshield washer fluid on a clean cloth. This will help to condition them.


Automatic Transmission Fluid Check the fluid level with the engine at normal operating temperature. 1. Park the vehicle on level ground. Start the engine, let it run until the radiator fan comes on, then shut off the engine. For accurate results, wait about 60 seconds (but no longer than 90 seconds) before doing step 2.


Do not use engine antifreeze or a vinegar/water solution in the windshield washer reservoir. Antifreeze can damage your vehicle's paint, while a vinegar/water solution can damage the windshield washer pump. Use only commercially-available windshield washer fluid.


198


DIPSTICK


2. Remove the dipstick (yellow loop) from the transmission, and wipe it with a clean cloth.


UPPER MARK LOWER MARK


3. Insert the dipstick all the way into


the transmission securely as shown in the illustration.


4. Remove the dipstick and check the


fluid level. It should be between the upper and lower marks.


10/08/06 08:34:41 11 ELEMENT MMC North America Owner's Man 50 31SCV680 enu


5. If the level is below the lower


mark, add fluid into the dipstick hole to bring it to the level between the upper and lower marks. Pour the fluid slowly and carefully so you do not spill any. Clean up any spill immediately; it could damage components in the engine compartment. Always use Honda ATF DW-1
(automatic transmission fluid).


Automatic Transmission Fluid, Brake Fluid


Use only Honda ATF DW-1 (automatic transmission fluid). Do not mix with other transmission fluids. Using transmission fluid other than Honda ATF DW-1 may cause deterioration in transmission operation and durability, and could result in damage to the transmission. Damage resulting from the use of transmission fluid other than Honda ATF DW-1 is not covered by the Honda new vehicle warranty.


6. Insert the dipstick all the way back


into the transmission securely as shown in the illustration.


The transmission should be drained and refilled with new fluid according to the Maintenance Minder™ (see page 185). If you are not sure how to add fluid, contact your dealer.


Brake Fluid Check the fluid level in the brake fluid reservoir monthly. Independent of the Maintenance Minder display, replace the brake fluid every 3 years. Always use Honda Heavy Duty

Loading...
x