2011 Honda Civic Sedan Owners Manual

After you’ve registered with XM Radio, keep your audio system in the XM radio mode while you wait for activation. This should take about 30
minutes.

While waiting for activation, make sure your vehicle remains in an open area with good reception. Once your audio system is activated, you’ll be able to listen to XM Radio broadcasts. XM Radio will continue to send an activation signal to your vehicle for at least 12 hours from the activation request. If the service has not been activated after 36 hours, contact XM Radio. In Canada, contact XM CANADA .

10/06/23 14:10:21 31SNA650_130

Audio System (Models without navigation system)

Playing a Disc

LOAD INDICATOR

CD BUTTON

EJECT BUTTON

REPEAT BUTTON

RANDOM BUTTON

DISPLAY BUTTON

SCAN BUTTON

SEEK/SKIP BUTTON

PWR/VOL KNOB

FOLDER KNOB

U.S. Si model is shown.

To Play a Disc To load or play discs, the ignition switch must be in the ACCESSORY (I) or ON (II) position.

You operate the disc player with the same controls used for the radio. To select the disc player, press the CD button. You will see ‘‘CD’’ in the display.

Do not use discs with adhesive labels. The label can curl up and cause the disc to jam in the unit.

CONTINUED

125

10/06/23 14:10:31 31SNA650_131

Audio System (Models without navigation system)

This audio system can also play CD-Rs and CD-RWs compressed in MP3 or WMA formats. When playing a disc in MP3, you will see ‘‘MP3’’ in the display. In WMA format, ‘‘WMA’’ will appear in the display.

A disc can support more than 99
folders, and each folder can hold up to 255 playable files. When there are more than 99 folders on a disc, the center display only shows two digits.

NOTE: If a file on WMA disc is protected by digital rights management (DRM), the audio unit displays CD FORMAT, and then skips to the next file.

Depending on the software the files were made with, it may not be possible to play some files, or display some text data.

Video CDs and DVDs do not work in this unit.

ToLoadaDisc Insert a disc about halfway into the disc slot. The drive will pull the disc in the rest of the way to play it. You operate the disc player with the same controls used for the radio. The number of the current track and the elapsed time are shown in the display. When playing a disc in MP3
or WMA, the numbers of the current folder and file, and the elapsed time are shown. The system will continuously play a disc until you change modes.

You cannot load and play 3-inch (8-cm) discs in this system.

TextDataDisplayFunction Each time you press the DISP button, the display shows you the text data on a disc, if the disc was recorded with text data.

126

10/06/23 14:10:44 31SNA650_132

Audio System (Models without navigation system)

You can see the album, artist, and track name in the display. If a disc is recorded in MP3 or WMA, you can see the folder and file name, and the album, artist, and track tag.

With the folder name, you will see the FOLDER indicator in the display. The TRACK indicator is shown with the file or track name.

If any letter is not available, it is replaced with ‘‘ . ’’ (dot) in the display. When the disc has no text data, you will see ‘‘NO INFO’’ on the display.

You will also see some text data under these conditions:

When a new folder, file, or track is selected.

The display shows up to 16
characters of selected text data (the folder name, file name, etc.).

When you change the audio mode to play a disc with text data or in MP3 or WMA.

If the text data has more than 16
characters, you will see the first 15
characters and the indicator in the display. Press and hold the DISP button until the next 16 characters are shown. You can see up to 31
characters of the text data.

＞

If you press and hold the DISP button again, the display shows the first 16 characters again.

When you insert a disc, and the system begins to play.

When playing a CD-DA with text data, the album and track name are shown in the display. With a disc in MP3 or WMA, the display shows the folder and file name.

ToChangeorSelectTracks/Files Use the SEEK/SKIP button while a disc is playing to select passages and change tracks (files in MP3/WMA mode).

−

Each time you

SEEK/SKIP press and release the side of the SEEK/SKIP button, the player skips forward to the beginning of the next track (file in MP3 or WMA mode). Press and release the

side to skip backward to the

beginning of the current track. Press it again to skip to the beginning of the previous track.

To move rapidly within a track, press and hold the or side of the SEEK/SKIP button.

CONTINUED

127

10/06/23 14:10:54 31SNA650_133

Audio System (Models without navigation system)

−

InMP3orWMAmode FOLDER SELECTION To select a different folder, turn the TUNE knob to move to the beginning of the next folder. Turn the knob to the right to skip to the next folder, and to the left to move to the beginning of the current folder. Turn it again to skip to the beginning of the previous folder. Turning the TUNE knob more than one click skips several folders at a time.

−

REPEAT (TRACK/FILE REPEAT) To continuously replay a track (files in MP3 or WMA mode), press and release the RPT button. You will see ‘‘RPT’’ in the display. Press and hold the RPT button for 2
seconds to turn it off.

InMP3orWMAmode FOLDER-REPEAT when activated, replays all files in the selected folder in the order they are compressed. To activate folder

This feature,

−

repeat, press the RPT button twice. You will hear a beep and see F-RPT in the display. The system continuously replays the current folder. Press the RPT button again to turn it off. Pressing the RDM button, or selecting a different folder with the TUNE knob also turns off the repeat feature.

Each time you press and release the RPT button, the mode changes from file repeat to folder repeat, then to normal play.

−

RANDOM (Random within a disc) This feature plays the tracks within a disc (the files in MP3
or WMA mode) in random order. To activate random play, press and release the RDM button. In MP3 or WMA mode, press the RDM button repeatedly to select RDM (within a disc random play). You will see ‘‘RDM’’ in the display. Press the RDM button for 2 seconds to return

128

to normal play.

−

This

InMP3orWMAmode FOLDER-RANDOM feature, when activated, plays all files in the selected folder in random order. To activate folder random, press and release the RDM button. You will see F-RDM in the display. The system will then select and play files randomly. This continues until you deactivate folder random by pressing and holding the RDM button for 2 seconds, or by selecting a different folder with the TUNE knob.

Each time you press and release the RDM button, the mode changes from folder random play to random play (within a disc random play), then to normal play.

10/06/23 14:11:05 31SNA650_134

Audio System (Models without navigation system)

−

SCAN (TRACK/FILE SCAN) The scan function samples all tracks (files in MP3 or WMA) on the disc in the order they are recorded on the disc. To activate scan, press the SCAN button. In MP3 or WMA mode, press the SCAN button repeatedly to select SCAN. You will see SCAN in the display. You will get a 10 second sampling of each track/ file on the disc. Press and hold the SCAN button again to get out of scan mode and play the last track/file sampled.

Pressing either side of the SEEK/ SKIP button also turns off the scan feature.

InMP3orWMAmode F-SCAN (FOLDER SCAN) This feature, when activated, samples the first file in each folder on the disc. To activate folder scan, press the SCAN button twice. You will see F-SCAN in the display.

−

The system plays the first file in the first folder for about 10 seconds. If you do nothing, the system will then play the first files in the next folders for 10 seconds. After playing the first file in the last folder, the system plays normally.

Pressing either side of the SEEK/ SKIP button, selecting a different folder with the TUNE knob, or pressing the SCAN button, also turns off the folder scan.

Each time you press and release the SCAN button, the mode changes from file scan to folder scan, then to normal play.

) to

To Stop Playing a Disc Press the eject button ( remove the disc. If you eject the disc, but do not remove it from the slot, the system will automatically reload it after 10 seconds and put it in pause mode. To begin playing, press the CD button.

You can also eject the disc when the ignition switch is off.

To play the radio when a disc is playing, press the AM/FM button. Press the CD button again to switch back to the CD player. Press the AUX button to switch to an appropriate audio unit.

CONTINUED

129

10/06/23 14:11:13 31SNA650_135

Audio System (Models without navigation system)

If you turn the system off while a disc is playing, either with the PWR/ VOL knob or by turning off the ignition switch, the disc will stay in the drive. When you turn the system back on, the disc will begin playing where it left off.

Operating the Optional Disc Changer An optional six or eight disc changer is available for your vehicle. This disc changer uses the same controls used for the in-dash disc player or the radio.

Load the desired discs in the magazine, and load the magazine in the changer according to the instructions that came with the unit.

To select the disc changer, press the CD button. The disc and track numbers will be displayed. To select a different disc, use the preset 4
button (DISC ) or the preset 1
button (DISC ). To select the previous disc, press the preset 4
button (DISC ), or the preset 1
− button (DISC ) to select the next ＋ disc in sequence.

− ＋

130

If you select an empty slot in the magazine, the changer will search for the next available disc to load and play.

Protecting Discs For information on how to handle and protect compact discs, see page 201

10/06/23 14:11:24 31SNA650_136

Disc Player Error Messages The chart on the right explains the error messages you may see in the display while playing a disc.

If you see an error message in the display while playing a disc, press the eject button. After ejecting the disc, check it for damage or deformation. If there is no damage, insert the disc again. For additional information on damaged discs, see page 202

The audio system will try to play the disc. If there is still a problem, the error message will reappear. Press the eject button, and pull out the disc. Insert a different disc. If the new disc plays, there is a problem with the first disc. If the error message cycle repeats and you cannot clear it, take your vehicle to a dealer.

Audio System (Models without navigation system)

Error Message

Cause

Solution

HEAT ERROR ＊

High Temperature

Track/File format not supported

Mechanical Error

UNSUPPORT

FORMAT BAD DISC

PLEASE CHECK

OWNER’S

MANUAL PUSH

EJECT

BAD DISC

PLEASE CHECK

Servo Error

OWNER’S MANUAL

＊

: Except Si model

Will disappear when the temperature returns to normal. Current track will be skipped. The next supported track or file plays automatically. Press the EJECT button and pull out the disc(s). Check the disc for serious damage, signs of deformation, excessive scratches, and/or dirt (see page 202 ). Insert the disc again. If the code does not disappear, or the disc(s) cannot be removed, consult your dealer. Do not try to force the disc out of the player.

131

10/06/23 14:11:37 31SNA650_137

Audio System (Models without navigation system)

Error Message

Cause

Solution

FOCUS Error

No disc in the disc magazine

Mechanical Error

No disc magazine in the disc changer High Temperature

Press the magazine eject button, and pull the magazine out. If the message does not disappear or the magazine cannot be pulled out, see your dealer. Insert disc.

Press the magazine eject button, pull the magazine out, check for an error message, then insert the magazine again. If the message does not disappear, or the magazine cannot be pulled out, see your dealer. Insert disc magazine.

Will disappear when the temperature returns to normal.

Optional Disc Changer Error Messages The chart on the right explains the error messages you may see in the display while playing a disc.

If you see an error message in the display while playing a disc, press the eject button. After ejecting the disc, check it for damage or deformation. If there is no damage, insert the disc again.

If there is still a problem, the error message will appear again. Press the eject button, and pull out the disc.

Insert a different disc. If the new disc plays, there is a problem with the first disc. If the error message cycle repeats and you cannot clear it, take your vehicle to a dealer.

132

10/06/23 14:11:42 31SNA650_138

Audio System (Models without navigation system)

Playing an iPod OnEX-L,Si,U.S.EX,andCanadianSEmodels

iPod INDICATOR

CD BUTTON

AM/FM BUTTON

U.S. Si model is shown.

REPEAT BUTTON

SEEK/SKIP BUTTON

RANDOM BUTTON

AUX BUTTON DISPLAY BUTTON

TUNE/SOUND KNOB

133

10/06/23 14:11:49 31SNA650_139

Audio System (Models without navigation system)

To Play an iPod This audio system can select and play the audio files on the iPod with the same controls used for the disc player. To play an iPod, connect it to the USB adapter cable in the console compartment by using your dock connector, then press the AUX button. The ignition switch must be in the ACCESSORY (I) or ON (II) position. The iPod will also be charged with the ignition switch in these positions.

The audio system reads and plays playable sound files on the iPod. The system cannot operate an iPod as a mass storage device. The system will only play songs stored on the iPod with iTunes.

iPod and iTunes are registered trademarks owned by Apple Inc.

iPods compatible with your audio system using the USB adapter cable are:

Model iPod classic (80/160 G) iPod classic (120 G) iPod with video (iPod 5th generation) iPod nano iPod nano 2nd generation iPod nano 3rd generation iPod nano 4th generation iPod nano 5th generation iPod touch iPod touch 2nd generation

Software

Ver. 1.1.2 or more

Ver. 2.0.1 or more

Ver. 1.3.0 or more

Ver. 1.3.1 or more Ver. 1.1.3 or more

Ver. 1.1.3 or more

Ver. 1.0.3 or more

Ver. 1.0.1 or more

Ver. 1.1.5 or more Ver. 2.2.1 or more

134

10/06/23 14:12:00 31SNA650_140

Use only compatible iPods with the latest software. iPods that are not compatible will not work in this audio unit.

Audio System (Models without navigation system)

NOTE:

Do not connect your iPod using a hub.

ConnectinganiPod

USB ADAPTER CABLE

USB CONNECTOR

Do not keep the iPod in the vehicle. Direct sunlight and high heat will damage it.

Do not use an extension cable between the USB adapter cable equipped with your vehicle and your dock connector.

We recommend backing up your data before playing it.

Some devices cannot be powered or charged via the USB adapter. If this is the case, use the accessory adapter to supply power to your device.

1.

Pull out the USB connector from the holder and remove the cable from the clip in the console compartment.

CONTINUED

135

10/06/23 14:12:09 31SNA650_141

Audio System (Models without navigation system)

If the iPod indicator does not appear in the audio display, check the connections, and try to reconnect the iPod a few times.

If the audio system still does not recognize the iPod, the iPod may need to be reset. Follow the instructions that came with your iPod, or you can find reset instructions online at itunes/

www.apple.com/

TextDataDisplayFunction Each time you press the DISP button, the display mode switches between the album name, the song/track name, the artist name, or name off (which turns off the text display).

The display shows up to 16
characters of the selected data. If the text data has more than 17
characters, you will see the first 15
characters and the indicator in the display. Press and hold the DISP button until the next 16 characters are shown.

＞

DOCK CONNECTOR

USB CONNECTOR

2.

Connect your dock connector to the iPod correctly and securely.

3.

Install the dock connector to the USB adapter cable securely.

136

10/06/23 14:12:20 31SNA650_142

Audio System (Models without navigation system)

ToChangeorSelectFiles Use the SKIP bar while an iPod is playing to select passages and change files.

ToSelectaFilefromiPodMenu

−

Each time you press and side of the SEEK/

SKIP release the SKIP button, the system skips forward to the beginning of the next file. Press and release the side of the button to skip backward to the beginning of the current file. Press it again to skip to the beginning of the previous file.

To move rapidly within a file, press and hold either side ( of the SEEK/SKIP button.

or

Press the TUNE/SOUND knob.

You can also select a file from any list on the iPod menu: playlists, artists, albums and songs, by using the TUNE/SOUND knob. Push the TUNE/SOUND knob to switch the display to an iPod menu, then turn the TUNE/SOUND knob to select a desired list.

After making a selection, wait for a few seconds until the display returns to the previous screen. The iPod menu is set. Pressing the TUNE knob cancels this setting mode before returning to the normal display.

Turn the TUNE knob to select an item. After making a selection, wait for a few seconds until the display returns to the previous screen. The system will then play the first file on the selected item.

If you select ‘‘ALL’’ on either the artists or albums list, all available files on the selected list are played.

CONTINUED

137

10/06/23 14:12:27 31SNA650_143

Audio System (Models without navigation system)

ToSelectRepeatorShuffleMode: You can select any type of repeat and shuffle modes by using the RPT and RDM buttons.

−

This feature

REPEAT continuously plays a file. To activate the repeat feature, press the RPT button. You will see ‘‘RPT’’ in the display. To turn it off, press the RPT button again.

−

This feature

SHUFFLE ALL plays all available files in a selected list (playlists, artists, albums or songs) in random order. To activate the shuffle all feature, press the RDM button. You will see ‘‘RDM’’ in the display. To turn it off, press and hold the RDM button.

NOTE: Available operating functions vary on models or versions. Some functions may not be available on the vehicle’s audio system.

−

This feature

SHUFFLE ALBUM plays all available albums in a selected list (playlists, artists, albums or songs) in random order. The files in each album are played in the recorded order. To activate the shuffle album feature, press the RDM button repeatedly. You will see ‘‘F-RDM’’ in the display. To turn it off, press and hold the RDM button.

Each time you press the RDM button, the mode changes from shuffle all play to shuffle album play, then to normal play.

138

10/06/23 14:12:37 31SNA650_144

To Stop Playing Your iPod To play the radio, press the AM/FM button. Press the CD button to switch to the disc mode (if a disc is loaded). Press the AUX button to switch the audio mode between the XM Radio (if equipped) and iPod.

Audio System (Models without navigation system)

＊

DisconnectinganiPod You can disconnect the iPod at any time when you see the ‘‘OK to disconnect’’ message in the iPod display. Always make sure you see the ‘‘OK to disconnect’’ message in the iPod display before you disconnect it. Make sure to follow the iPod’s instructions on how to disconnect the dock connector from the USB adapter cable.

＊

The displayed message may vary on models or versions. On some models, there is no message to disconnect.

When you disconnect the iPod while it is playing, the display shows ‘‘USB NO DATA.’’

If you reconnect the same iPod, the system may begin playing where it left off, depending on what mode the iPod is in when it is reconnected.

iPod Error Messages If you see an error message in the display, see page

140

139

10/06/23 14:12:43 31SNA650_145

Audio System (Models without navigation system)

iPod Error Messages If you see an error message on the audio display while playing an iPod, find the solution in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer.

Error Message

Cause

Solution

USB ERROR BAD USB DEVICE

PLEASE CHECK

OWNERS MANUAL

USB ROM Error

Appears when an incompatible device is connected

iPod NO SONG

No files in iPod

UNSUPPORTED

VER.

Use of unsupported iPod

CONNECT

RETRY

Recognition failure of iPod

There is a problem with the USB adapter unit. Disconnect the device. Then, turn the audio system off, and turn it on again. Do not reconnect the device that caused the error.

Appears when the iPod is empty. Store some files in the iPod. Appears when an unsupported iPod is connected. See page 134 for the specification information for iPods. If it appears when a supported iPod is connected, update the iPod software to the newer version. Appears when the system does not acknowledge the iPod. Reconnect the iPod.

140

10/06/23 14:12:49 31SNA650_146

Audio System (Models without navigation system)

Playing a USB Flash Memory Device OnEX-L,Si,U.S.EX,andCanadianSEmodels

USB INDICATOR

CD BUTTON

AM/FM BUTTON SCAN BUTTON

U.S. Si model is shown.

REPEAT BUTTON

SEEK/SKIP BUTTON

RANDOM BUTTON

AUX BUTTON DISPLAY BUTTON

TUNE/FOLDER KNOB

141

10/06/23 14:12:58 31SNA650_147

Audio System (Models without navigation system)

To Play a USB Flash Memory Device This audio system can select and play the audio files on a USB flash memory device with the same controls used for the disc player. To play a USB flash memory device, connect it to the USB adapter cable in the console compartment, then press the AUX button. The ignition switch must be in the ACCESSORY (I) or ON (II) position.

＊

The audio system reads and plays the audio files on the USB flash memory device in MP3, WMA or AAC formats. Depending on the format, the display shows MP3, WMA or AAC when a USB flash memory device is playing. The USB flash memory device limit is up to 700 folders or up to 65535 files.

＊

Only AAC format files recorded with iTunes are playable on this audio unit.

The recommended USB flash memory devices are 256 MB or higher, and formatted with the FAT file system. Some digital audio players may be compatible as well.

Some USB flash memory devices (such as devices with security lock- out features, etc.) will not work in this audio unit.

NOTE:

Do not use a device such as a card reader or hard drive as the device or your files may be damaged.

Do not connect your USB flash memory device using a hub.

142

10/06/23 14:13:08 31SNA650_148

Do not use an extension cable to the USB adapter cable equipped with your vehicle.

Do not keep a USB flash memory device in the vehicle. Direct sunlight and high heat will damage it.

We recommend backing up your data before playing a USB flash memory device.

Some devices cannot be powered or charged via the USB adapter. If this is the case, use the accessory adapter to supply power to your device.

Depending on the type and number of files, it may take some time before they begin to play.

Audio System (Models without navigation system)

Depending on the software the files were made with, it may not be possible to play some files, or display some text data.

Depending on the type of encoding and writing software used, there may be cases where character information does not display properly.

The order of files in USB playback may be different from the order of files displayed in PC or other devices etc. Files are played in the order stored in USB flash memory device.

Some versions of MP3, WMA, or AAC format may not be supported. If an unsupported file is found, the audio unit displays UNSUPPORTED, then skips to the next file.

In WMA or AAC format, DRM (digital rights management) files cannot be played. If the system finds a DRM file, the audio unit displays UNPLAYABLE FILE, and then skips to the next file.

Combining a low sampling f requency with a low bitrate may result in extremely degraded sound quality.

CONTINUED

143

10/06/23 14:13:19 31SNA650_149

Audio System (Models without navigation system)

ConnectingaUSBFlashMemory Device

USB ADAPTER CABLE

USB CONNECTOR

1.

Pull out the USB connector from the holder and remove the cable from the clip in the console compartment.

USB CONNECTOR

2.

Connect the USB flash memory device to the USB connector correctly and securely.

When the USB flash memory device is connected, the USB indicator is shown in the display.

144

TextDataDisplayFunction Each time you press the DISP button, the display mode shows you in sequence, the folder name, the file name, the artist tag, the album tag, the track tag and name off (which turns off the text display).

The display shows up to 16
characters of the selected data. If the text data has more than 17
characters, you will see the first 15
characters and the indicator in the display. Press and hold the DISP button until the next 16 characters are shown.

＞

10/06/23 14:13:30 31SNA650_150

ToChangeorSelectFiles Use the SKIP bar while a USB flash memory device is playing to select passages and change files.

−

Each time you press and side of the SEEK/

SKIP release the SKIP button, the system skips forward to the beginning of the next file. Press and release the side of the button to skip backward to the beginning of the current file. Press it again to skip to the beginning of the previous file.

To move rapidly within a file, press and hold either side ( of the SEEK/SKIP button.

or

Audio System (Models without navigation system)

−

FOLDER SELECTION To select a different folder, turn the TUNE knob to move to the beginning of the next folder. Turn the knob to the right to skip to the next folder, and to the left to move to the beginning of the current folder. Turn it again to skip to the beginning of the previous folder. Turning the TUNE knob more than one click skips several folders at a time.

ToSelectRepeat,RandomorScan Mode: You can select any type of repeat, random and scan modes by using the RPT button, RDM button, or SCAN button.

−

This feature

REPEAT continuously plays a file. To activate the repeat feature, press the RPT button. You will see ‘‘RPT’’ in the display. To turn it off, press and hold the RPT button.

−

This feature

FOLDER REPEAT replays all the files in the selected folder in the order they are stored. To activate the folder repeat feature, press the RPT button repeatedly. You will see ‘‘F-RPT’’ in the display. To turn it off, press and hold the RPT button.

Each time you press and release the RPT button, the mode changes from file repeat to folder repeat, then to normal play.

CONTINUED

145

10/06/23 14:13:36 31SNA650_151

Audio System (Models without navigation system)

−

This feature plays the

RANDOM files within a USB flash memory device in random order. To active random play, press the RDM button twice. You will see RDM in the display. Press and release the RDM button to return to normal play.

−

This

FOLDER-RANDOM feature, when activated, plays all files in the selected folder in random order. To activate folder random, press and release the RDM button. You will see F-RDM in the display. The system will then select and play files randomly. This continues until you deactivate folder random by pressing and holding the RDM button for 2 seconds, or by selecting a different folder with the TUNE knob.

−

This feature samples all

SCAN files in the current folder in the order they are stored. To activate the scan feature, press the SCAN button. You will see ‘‘SCAN’’ in the display. You will get a 10 second sampling of each file in the folder. Press and hold the SCAN button to get out of the scan mode and play the last file sampled.

Each time you press and release the RDM button, the mode changes from folder random, to all random, then to normal play.

146

10/06/23 14:13:46 31SNA650_152

Audio System (Models without navigation system)

− This feature

FOLDER SCAN samples the first file in each folder in the order they are stored. To activate the folder scan feature, press the SCAN button repeatedly. You will see ‘‘F-SCAN’’ in the display. You will get a 10 second sampling of the first file in each folder. Press and hold the SCAN button to get out of the folder scan mode and play the last file sampled.

Each time you press and release the SCAN button, the mode changes from file scan to folder scan, then to normal play.

To Stop Playing a USB Flash Memory Device To play the radio, press the AM/FM button. Press the CD button to switch to the disc mode (if a disc is loaded). Press the AUX button to switch the audio mode between the USB or XM Radio (if equipped).

DisconnectingaUSBFlashMemory Device You can disconnect the USB flash memory device at any time even if the USB mode is selected on the audio system. Always follow the USB flash memory device’s instructions when you remove it.

When you disconnect the USB flash memory device while it is playing, the display shows ‘‘USB NO DATA.’’

If you reconnect the same USB flash memory device, the system will begin playing where it left off.

USB Flash Memory Device Error Messages If you see an error message in the display, see page

148

147

10/06/23 14:13:52 31SNA650_153

Audio System (Models without navigation system)

USB Flash Memory Device Error Messages If you see an error message on the audio display while playing a USB flash memory device, find the solution in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer.

Error Message

Cause

Solution

USB ERROR BAD USB DEVICE

PLEASE CHECK

OWNERS MANUAL

USB ROM Error

Appears when an incompatible device is connected

UNPLAYABLE

FILE

Use of unsupported files

USB NO SONG

No files in USB flash memory device

UNSUPPORTED

Use of unsupported USB flash memory device

There is a problem with the USB adapter unit. Disconnect the device. Then, turn the audio system off, and turn it on again. Do not reconnect the device that caused the error.

Appears when the files in the USB flash memory device are DRM or an unsupported format. This error message appears for about 3
seconds, then plays the next song. Appears when the USB flash memory device is empty or there are no MP3, WMA, or AAC files in the USB flash memory device. Save some MP3, WMA, or AAC files in the USB flash memory device. Appears when an unsupported device is connected. See page 142 for the specification information for the USB flash memory device. If it appears when the supported device is connected, reconnect the device.

148

10/06/23 14:13:59 31SNA650_154

Audio System (Models with navigation system)

Voice Control System The audio system can also be operated by voice control. See the navigation system manual for complete details.

Playing the AM/FM Radio

FM2 ICON

FM1 ICON

AM ICON

AM/FM BUTTON AUDIO BUTTON SCAN BUTTON

TUNE BAR

PRESET BUTTONS

U.S. Si model is shown.

AUTO SELECT ICON BACKGROUND ICON SOUND ICON

149

10/06/23 14:14:09 31SNA650_155

Audio System (Models with navigation system)

The band and frequency that the radio was last tuned to are displayed. To change bands, press the AM/FM button, or touch the desired band icon (FM1, FM2, AM, XM1 , or XM2 ). On the FM band, STEREO will be displayed if the station is broadcasting in stereo. Stereo reproduction on AM is not available.

＊

＊

＊

If equipped

For information on XM Radio, see page

153

To Play the AM/FM Radio The ignition switch must be in the ACCESSORY (I) or ON (II) position. Turn the system on by pushing the power/volume knob or the AM/FM button. Adjust the volume by turning the power/volume knob.

Pushing the AUDIO button will also turn on the system.

You can also operate the audio system without using the control icons on the audio screen. Use the control buttons on the left side of the screen. The status bar appears on the bottom of the screen each time you operate any of the control buttons. On the navigation screen, you can also see audio information by touching the AUDIO INFO icon on the lower half of the screen.

150

To Select a Station You can use any of five methods to find radio stations on the selected band: tune, seek, scan, the preset buttons, and auto select.

−

Use the TUNE bar to tune

TUNE the radio to a desired frequency. Press the side of the bar to tune to a higher frequency, and press the

▲

▼

side to tune to a lower

frequency.

or

▲ ▼

Press and hold the side of the TUNE bar until you hear two beeps to change the frequency rapidly. Release the bar when the display reaches the desired frequency.

10/06/23 14:14:19 31SNA650_156

−

The seek function

SEEK searches up and down from the current frequency to find a station with a strong signal. To activate it, press and hold the side of the TUNE bar until you hear a beep, then release it.

▲ ▼

or

−

SCAN The scan function samples all stations with strong signals on the selected band. To activate it, press the SCAN button, then release it. You will see SCAN in the display. When the system finds a strong signal, it will stop and play that station for about 10 seconds.

Audio System (Models with navigation system)

If you do nothing, the system will then scan for the next strong station and play it for 10 seconds. When it plays a station you want to listen to, press the SCAN button again.

Each preset button’s frequency is shown on the bottom of the audio display.

−

Each preset button can

Preset store one frequency on AM and two frequencies on FM.

1.

2.

Select the desired band, AM or FM. FM1 and FM2 let you store six stations each.

Use the tune, seek, or scan function to tune the radio to a desired station.

3.

Pick a preset button, and hold it until you hear a beep.

4.

Repeat steps 1 through 3 to store a total of six stations on AM and twelve stations on FM.

CONTINUED

151

10/06/23 14:14:25 31SNA650_157

Audio System (Models with navigation system)

− If you are

AUTO SELECT traveling far from home and can no longer receive your preset stations, you can use the auto select feature to find stations in the local area.

Press the AUDIO button to view the audio control icons, then touch the AUTO SEL icon. You will see AUTO SEL flashing in the display, and the system goes into scan mode for several seconds. It stores the frequencies of six AM, and twelve FM stations in the preset buttons.

You will see a ‘‘0’’ displayed after pressing a preset button if auto select cannot find a strong station for every preset button.

If you do not like the stations auto select has stored, you can store other frequencies on the preset buttons as previously described.

Toturnoffautoselect, AUTO SEL icon. This restores the presets you originally set.

press the

For information on AM/FM radio frequencies and reception, see page 199

152

10/06/23 14:14:32 31SNA650_158

Playing the XM Radio

POWER/VOLUME KNOB

AM/FM BUTTON

XM RADIO BUTTON

AUDIO BUTTON

SCAN BUTTON PRESET CHANNEL NUMBER

Audio System (Models with navigation system)

XM RADIO ICON

MODE ICON

JOYSTICK

CHANNEL INDICATOR

CONTINUED 153

U.S. Si model is shown.

TUNE BAR

PRESET BUTTONS

10/06/23 14:14:40 31SNA650_159

Audio System (Models with navigation system)

Operating the XM Radio To listen to XM Radio, turn the ignition switch to the ACCESSORY (I) or the ON (II) position. Push the power/volume knob to turn on the audio system, and press the XM RADIO button. Adjust the volume by turning the knob. The last channel you listened to will show in the display.

You can also operate the radio using the control buttons on the left side of the screen. The status bar appears on the bottom of the screen each time you press any of the control buttons. On the navigation screen, you can also see the audio information by touching the AUDIO INFO icon on the lower part of the screen.

You can also change to the XM Radio while you are listening to an FM station, AM station, disc, PC card, etc., by touching the XM1 or XM2 icon on the audio display.

−

To switch between

MODE channel mode and category mode, touch the MODE icon. In channel mode, you can select all of the available channels. In category mode, such as Jazz, Rock, Classical, etc., you can select all of the channels within that category. Each time you touch and release the MODE icon, the display changes between the channel mode and the category mode.

Your audio system is capable of receiving XM Radio anywhere in the United States, except Hawaii, Alaska, and Puerto Rico.

XM is a registered trademark of Sirius XM Radio , Inc.

XM Radio receives signals from two satellites to produce clear, high- quality digital reception. It offers many channels in several categories. Along with a large selection of different types of music, XM Radio allows you to view channel and category selections in the display. When you press and hold the AUDIO button, the display also shows all XM information.

154

10/06/23 14:14:52 31SNA650_160

Audio System (Models with navigation system)

TUNE Press the TUNE bar to change channel selections. Press

−

for lower numbered

for higher numbered channels ▼

▲ and channels. In the category mode, you can only select channels within that category.

Press and hold

−

CATEGORY either side of the TUNE bar to select another category.

or

) until you hear a beep

On the audio display, you will see the selected CHANNEL (number), CATEGORY, NAME (artist name), and TITLE (music title).

You may experience periods when XM Radio does not transmit the artist’s name and song title information. If this happens, there is nothing wrong with your system.

−

The scan function gives

SCAN you a sampling of all channels while in the channel mode. In the category mode, only the channels within that category are scanned. To activate scan, press the SCAN button or touch the SCAN icon on the screen. The system plays each channel in numerical order for a few seconds, then selects the next channel. When you hear a channel you want to listen to, press the button or touch the icon again.

−

Preset You can store up to 12
preset channels using each preset button or preset icons on the screen. Each preset button or icon stores one channel from the XM1 band and one channel from the XM2 band.

To store a channel:

1.

2.

Press the XM RADIO button. Either XM1 or XM2 will show in the display.

Use the tune, seek, or scan function to tune to a desired channel.

In category mode, only channels within that category can be selected. In channel mode, all channels can be selected.

3.

Pick the preset button (icon) you want for that channel. Press and hold the button (icon) until you hear a beep.

CONTINUED

155

10/06/23 14:15:02 31SNA650_161

Audio System (Models with navigation system)

4.

Repeat steps 2 and 3 to store the first six channels.

5.

Press the XM RADIO button again or touch the other XM icon (XM1
or XM2) on the audio display. Store the next six channels using steps 2 and 3.

Once a channel is stored, press and release the proper preset button (icon) to tune to it. Each preset button’s channel is shown on the bottom of the audio display.

156

ToSelectaChannelfromList

CHANNEL LIST ICON

You can also select a desired channel from the list shown on the screen. Press the AUDIO button to show the audio control display on the navigation screen.

Touch the CHANNEL LIST icon to switch the display to the channel list which shows all channels in all categories. Select and touch a desired channel.

or

▲ ▼

To scroll through the display, touch the icon on the side of the screen. To go back to the previous display, touch the Return icon on the screen.

10/06/23 14:15:11 31SNA650_162

To select a desired icon with the joystick, move it in the appropriate direction, then press ENT.

Audio System (Models with navigation system)

XM Radio Display Messages ‘‘LOADING’’ audio or program information.

XM is loading the

−

−

‘‘OFF AIR’’ currently selected is no longer broadcasting.

The channel

−

The encryption

‘‘UPDATING’’ code is being updated. Wait until the encryption code is fully updated. Channels 0 and 1 should still work normally.

−

The signal is

‘‘NO SIGNAL’’ currently too weak. Move the vehicle to an area away from tall buildings, and with an unobstructed view of the southern horizon.

−

The selected channel

‘‘ - - - - ’’ number does not exist or is not part of your subscription.

−

‘‘NO INFO’’ channel has no artist or title information at this time.

The selected

‘‘ANTENNA’’ There is a problem with the XM antenna. Please consult your dealer.

−

CONTINUED

157

10/06/23 14:15:19 31SNA650_163

Audio System (Models with navigation system)

Signal may be blocked by mountains or large obstacles to the south.

Signal weaker in these areas.

SATELLITE

158

GROUND REPEATER

The XM satellites are in orbit over the equator; therefore, objects south of the vehicle may cause satellite reception interruptions. To help compensate for this, ground-based repeaters are placed in major metropolitan areas.

Satellite signals are more likely to be blocked by tall buildings and mountains the farther north you travel from the equator. Carrying large items on a roof rack can also block the signal.

Depending on where you drive, you may experience reception problems. Interference can be caused by any of these conditions:

Driving on the north side of an east/west mountain road.

Driving on the north side of a large commercial truck on an east/west road.

10/06/23 14:15:30 31SNA650_164

Audio System (Models with navigation system)

Driving in tunnels.

Driving on a road beside a vertical wall, steep cliff, or hill to the south of you.

Driving on the lower level of a multi-tiered road.

Driving on a single lane road alongside dense trees taller than 50 ft. (15 m) to the south of you.

Large items carried on a roof rack.

There may be other geographic situations that could affect XM Radio reception.

AsrequiredbytheFCC: Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

Receiving XM Radio Service If your XM Radio service has expired or you purchased your vehicle from a previous owner, you can listen to a sampling of the broadcasts available on XM Radio. With the ignition switch in the ACCESSORY (I) or ON (II) position, push the power/volume knob to turn on the audio system and press the XM RADIO button. A variety of music types and styles will play.

, or at

If you decide to purchase XM Radio service, contact XM Radio at www.xmradio.com 1-800-852-9696. You will need to give them your radio I.D. number and your credit card number. To get your radio I.D. number, press the TUNE bar until ‘‘0’’ appears in the display. Your I.D. will appear in the display.

After you’ve registered with XM Radio, keep your audio system in the XM radio mode while you wait for activation. This should take about 30
minutes.

While waiting for activation, make sure your vehicle remains in an open area with good reception. Once your audio system is activated, you’ll be able to listen to XM Radio broadcasts. XM Radio will continue to send an activation signal to your vehicle for at least 12 hours from the activation request. If the service has not been activated after 36 hours, contact XM Radio. In Canada, contact XM CANADA .

159

10/06/23 14:15:44 31SNA650_165

Audio System (Models with navigation system)

Adjusting the Sound

SPEAKER SETTING

SOUND ICON

BASS/TREBLE SETTING

You can adjust the sound on the navigation screen. To adjust the sound, push the AUDIO button, then enter the sound grid by touching the SOUND icon on the display.

160

BASS

−

Adjusts the bass.

−

Adjusts the treble. To

TREBLE adjust the treble and bass, touch either bass adjustment bar. The adjustment bar on the lower right display shows you the current setting.

on the treble or

or

−

FADER Adjusts the front-to-back strength of the sound. To adjust the front/rear fader, touch the FR or RR icon.

−

Adjusts the side-to-

BALANCE side strength of the sound. To adjust the left/right balance, touch the L or R icon.

−

Adjusts the

SUBWOOFER strength of sound from the subwoofer speaker. To adjust the sound strength, touch

or

on each side of the adjustment

bar.

The right upper display shows you the current setting of the sound strength coming from each speaker.

−

The SVC mode

SVC (speed-sensitive volume compensation)