mechanic.
Important Safety Precautions To eliminate potential hazards, read the instructions before you begin, and make sure you have the tools and skills required.
Make sure your vehicle is parked on level ground, the parking brake is set, and the engine is off. To clean parts, use a commercially available degreaser or parts cleaner, not gasoline. To reduce the possibility of fire or explosion, keep cigarettes, sparks, and flames away from the battery and all fuel-related parts. Wear eye protection and protective clothing when working with the battery or compressed air.
212
Improperly maintaining this vehicle, or failing to correct a problem before driving can cause a crash in which you can be seriously hurt or killed.
Always follow the inspection and maintenance recommendations and schedules in this owner’s manual.
Injury from moving parts. not run the engine unless instructed to do so.
Do
Failure to properly follow maintenance instructions and precautions can cause you to be seriously hurt or killed.
Always follow the procedures and precautions in this owner’s manual.
Potential Vehicle Hazards
Carbon Monoxide poison from engine exhaust. Be sure there is adequate ventilation whenever you operate the engine.
Burns from hot parts. Let the engine and exhaust system cool down before touching any parts.
Some of the most important safety precautions are given here. However, we cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task.
Main MenuTable of ContentsstYour vehicle displays engine oil life and maintenance service items on the information display to show you when you should have your dealer perform engine oil replacement and indicated maintenance service.
Based on the engine operating conditions and accumulated engine revolutions, the onboard computer in your vehicle calculates the remaining engine oil life and displays it as a percentage.
Engine Oil Life Display SEL/RESET BUTTON
ENGINE OIL LIFE DISPLAY
To see the current engine oil life, turn the ignition switch to the ON (II) position, and press the SEL/ RESET button repeatedly until the engine oil life display appears (see page
66
).
Maintenance Minder
The remaining engine oil life is displayed on the information display according to this table:
Calculated Engine
Displayed
Oil Life (%) 100 % 91 % 90 % 81 % 80 % 71 % 70 % 61 % 60 % 51 % 50 % 41 % 40 % 31 % 30 % 21 % 20 % 16 % 15 % 11 % 10 % 6 % 5 % 1 %
− − − − − − − − − − − − 0 %
Engine Oil Life (%)
100 % 90 % 80 % 70 % 60 % 50 % 40 % 30 % 20 % 15 % 10 % 5 % 0 %
CONTINUED
213
Main MenuTable of ContentsstMaintenance Minder
MAINTENANCE ITEM CODE(S)
ENGINE OIL LIFE INDICATOR
If the remaining engine oil life is 15
to 6 percent, you will see the engine
oil life indicator every time you turn
the ignition switch to the ON (II)
position. The maintenance minder
indicator will also come on, and the
maintenance item code(s) for other
scheduled maintenance items
needing service will be displayed
next to the engine oil life indicator.
214
The 15 and 10 percent oil life indicator reminds you that the time is coming soon to take your vehicle in for the required maintenance.
SERVICE MESSAGE
When the remaining engine oil life is 5 to 1 percent, you will see a ‘‘SERVICE’’ message along with the same maintenance item code(s), every time you turn the ignition switch to the ON (II) position.
Main MenuTable of ContentsstMaintenance Minder
The maintenance item code or codes indicate the main and sub items required at the time of the oil change (see page
216
).
You can switch the display to the odometer, the trip meter, and the outside temperature indicator (if equipped) by pushing the SEL/ RESET button on the dashboard repeatedly.
When the engine oil life is 15 to 1
percent, the maintenance minder
indicator (
) comes on every
time you turn the ignition switch to
the ON (II) position, then it goes out
if you switch the information display.
When you see this message, have the indicated maintenance performed by your dealer as soon as possible.
NEGATIVE MILEAGE
When the remaining engine oil life is 0 percent, the engine oil life indicator will blink. The display comes on everytimeyouturntheignition switch to the ON (II) position. The maintenance minder indicator on in the instrument panel. When you see this message, immediately have the indicated maintenance done by your dealer.
) also comes on and remains
If you do not perform the indicated maintenance, negative mileage is displayed and begins to blink after the vehicle has been driven 10 miles (10 km) or more. Negative mileage means your vehicle has passed the maintenance required point. Immediately have the indicated maintenance done by your dealer.
215
Main MenuTable of ContentsstMaintenance Minder
You can change the information display from the engine oil life display to the odometer, the trip meter, or the outside temperature (if equipped) every time you press and release the SEL/RESET button.
When the engine oil life is 0 percent or negative mileage, the maintenance minder indicator ) remains on even if you change the information display.
Immediately have the service done, and make sure to reset the display (see Resetting the Engine Oil Life Display).
216
Maintenance Main Items and Sub Items
MAINTENANCE MAIN ITEM
MAINTENANCE SUB ITEM
All maintenance items displayed in the information display are in code. For an explanation of these maintenance codes, see page
219
Resetting the Engine Oil Life Display Your dealer will reset the display after completing the required maintenance service. You will see ‘‘OIL LIFE 100%’’ on the information display the next time you turn the ignition switch to the ON (II) position.
If maintenance service is done by someone other than your dealer, reset the maintenance minder as follows:
1.
Turn the ignition switch to the ON (II) position.
2.
Press the SEL/RESET button repeatedly until the engine oil life indicator is displayed.
Main MenuTable of Contentsst3.
Press the SEL/RESET button for about 10 seconds. The engine oil life and the maintenance item code(s) will blink.
4.
Press the SEL/RESET button for more than 5 seconds. The maintenance item code(s) will disappear, and the engine oil life will reset to ‘‘100.’’
Maintenance Minder
Important Maintenance Precautions If you have the required service done but do not reset the display, or reset the display without doing the service, the system will not show the proper maintenance intervals. This can lead to serious mechanical problems because you will no longer have an accurate record of when maintenance is needed.
Your authorized Honda dealer knows your vehicle best and can provide competent, efficient service.
CONTINUED
217
Main MenuTable of ContentsstMaintenance Minder
However, service at a dealer is not mandatory to keep your warranties in effect. Maintenance may be done by any qualified service facility or person who is skilled in this type of automotive service. Make sure to have the service facility or person reset the display as previously described. Keep all receipts as proof of completion, and have the person who does the work fill out the maintenance record. Check your warranty booklet for more information.
We recommend using Honda parts and fluids whenever you have maintenance done. These are manufactured to the same high quality standards as the original components, so you can be confident of their performance and durability.
218
Maintenance,
U.S. Vehicles: replacement, or repair of emissions control devices and systems may be done by any automotive repair establishment or individual using parts that are ‘‘certified’’ to EPA standards.
#
According to state and federal regulations, failure to perform maintenance on the items marked with will not void your emissions warranties. However, all maintenance services should be performed in accordance with the intervals indicated by the information display.
Owner’s Maintenance Checks Youshouldcheckthefollowing items at the specified intervals. If you are unsure of how to perform any check, turn to the appropriate page listed.
Engine oil level Check every time you fill the fuel tank. See page
179
−
Engine coolant level Check the radiator reserve tank every time you fill the fuel tank. See page
−
181
Automatic transmission Check
the fluid level monthly. See page
232
−
Brakes Check the fluid level monthly. See page
234
−
−
Tires Check the tire pressure
monthly. Examine the tread for
wear and foreign objects. See page
245
−
Lights Check the operation of the headlights, parking lights, taillights, high-mount brake light, and license plate lights monthly. See page
236
Main MenuTable of ContentsstSymbol
Maintenance Main Items
Replace engine oil Replace engine oil and oil filter Inspect front and rear brakes Check parking brake adjustment Inspect these items:
Tie rod ends, steering gear box, and boots Suspension components Driveshaft boots Brake hoses and lines (including ABS) All fluid levels and condition of fluids Exhaust system # Fuel lines and connections #
1 :
If the message ‘‘SERVICE’’ does not appear more than 12 months after the display is reset, change the engine oil every year.
#
: See information on maintenance and emissions warranty on page
185
NOTE:
Independent of the maintenance minder display, replace the brake fluid every 3 years. Inspect idle speed every 160,000 miles (256,000 km). Adjust the valves during services A, B, 1, 2, or 3 only if they are noisy.
Symbol
Maintenance Minder
Maintenance Sub Items
Rotate tires Replace air cleaner element
If you drive in dusty conditions, replace every 15,000 miles (24,000 km).
Replace dust and pollen filter
If you drive primarily in urban areas that have high
concentrations of soot in the air from industry and
from diesel-powered vehicles, replace every 15,000
miles (24,000 km).
Inspect drive belt Replace transmission fluid Replace spark plugs Inspect valve clearance Replace engine coolant
219
Main MenuTable of ContentsstMaintenance Record
You or the servicing dealer can record all completed maintenance here. When maintenance is performed, record the mileage, circle the coded item(s) completed, and write in any other non-coded items (such as brake fluid replacement) below the codes. Keep the receipts for all work done on your vehicle. Maintenance can also be recorded in your Honda service history booklet.
Mileage
Maintenance Performed
Signature
Date
Mileage
Maintenance Performed
Signature
Date
mi km
mi km
mi km
mi km
mi km
mi km
mi km
220
mi km
mi km
mi km
mi km
mi km
mi km
mi km
Main MenuTable of ContentsstMileage
Maintenance Performed
Signature
Date
Mileage
Maintenance Performed
Signature
Date
Maintenance Record
mi km
mi km
mi km
mi km
mi km
mi km
mi km
mi km
mi km
mi km
mi km
mi km
mi km
mi km
221
Main MenuTable of ContentsstFluid Locations
Except U.S. Si model
POWER STEERING FLUID (Red cap)
WASHER FLUID (Blue cap)
ENGINE OIL FILL CAP
ENGINE OIL DIPSTICK (Orange loop)
BRAKE FLUID (Black cap)
CLUTCH FLUID (Manual Transmission only) (Light gray cap)
AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow loop)
ENGINE COOLANT RESERVOIR
222
RADIATOR CAP
Main MenuTable of ContentsstU.S. Si model
WASHER FLUID (Blue cap)
ENGINE OIL DIPSTICK (Orange handle)
ENGINE OIL FILL CAP
BRAKE FLUID (Black cap)
Fluid Locations
CLUTCH FLUID (Light gray cap)
ENGINE COOLANT RESERVOIR
RADIATOR CAP
223
Main MenuTable of ContentsstAdding Engine Oil
ENGINE OIL FILL CAP
ENGINE OIL FILL CAP
Except U.S. Si
U.S. Si
Unscrew and remove the engine oil fill cap on the valve cover. Pour in the oil slowly and carefully so you do not spill any. Clean up any spills immediately. Spilled oil could damage components in the engine compartment.
Reinstall the engine oil fill cap, and tighten it securely. Wait a few minutes, and recheck the oil level on the engine oil dipstick. Do not fill above the upper mark; you could damage the engine.
224
Recommended Engine Oil Oil is a major contributor to your engine’s performance and longevity. Always use a premium-grade detergent oil displaying the API Certification Seal. This seal indicates the oil is energy conserving, and that it meets the American Petroleum Institute’s latest requirements. It is highly recommended that you use Honda Motor Oil in your vehicle for optimum engine protection.
API CERTIFICATION SEAL
Main MenuTable of ContentsstMake sure the API Certification Seal says ‘‘For Gasoline Engines.’’
U.S. Si model:
The oil viscosity or weight is provided on the container’s label.
All models except U.S. Si: Honda Motor Oil is the preferred 5W-20 lubricant for your vehicle. 5W-20 oil is formulated for year- round protection of your vehicle, to improve cold weather starting and fuel economy.
Ambient Temperature
An oil with a viscosity of 5W-30 is preferred for improved fuel economy and year-round protection in your vehicle. You may use a 10W-30 oil if the temperature in your area never goes below 20°F (
7°C).
−
Ambient Temperature
Adding Engine Oil
Synthetic Oil You may use a synthetic motor oil if it meets the same requirements given for a conventional motor oil: it displays the API certification seal, and it is the proper weight. You must follow the oil and filter change intervals shown on the information display.
Engine Oil Additives Your vehicle does not require any oil additives. Additives may adversely affect the engine or transmission performance and durability.
225
Main MenuTable of ContentsstDRAIN BOLT
WASHER
WASHER
DRAIN BOLT
Except U.S. Si
1.
Run the engine until it reaches normal operating temperature, then shut it off.
U.S. Si Open the hood, and remove the 2. engine oil fill cap. Remove the oil drain bolt and washer from the bottom of the engine. Drain the oil into an appropriate container.
Changing the Oil and Filter
Always change the oil and filter according to the maintenance messages shown on the information display. The oil and filter collect contaminants that can damage your engine if they are not removed regularly.
Changing the oil and filter requires special tools and access from underneath the vehicle. The vehicle should be raised on a service station- type hydraulic lift for this service. Unless you have the knowledge and proper equipment, you should have this maintenance done by a skilled mechanic.
226
Main MenuTable of ContentsstOIL FILTER
Except U.S. Si
U.S. Si
3.
Remove the oil filter, and let the remaining oil drain. A special wrench (available from your dealer) is required.
Make sure the oil filter gasket is not stuck to the engine block. If it is, remove it before installing a new oil filter.
4.
Install a new oil filter according to the instructions that come with it.
Make sure to clean off any dirt and dust on the connecting surface of a new oil filter.
5.
Put a new washer on the drain bolt, then reinstall the drain bolt. Tighten the drain bolt to: 29 lbf·ft (39 N·m , 4.0 kgf·m)
Changing the Oil and Filter
6.
Refill the engine with the recommended oil. Engine oil change capacity (including filter):
Except U.S. Si 3.9 US qt (3.7 )
U.S. Si 4.6 US qt (4.4 )
7.
Replace the engine oil fill cap.
Start the engine. The oil pressure
indicator should go out within 5
seconds. If it does not, turn off the
engine, and check your work.
8.
Let the engine run for several minutes, then check the drain bolt and oil filter for leaks.
CONTINUED
227
Main MenuTable of ContentsstChanging the Oil and Filter, Engine Coolant
9.
Turn off the engine, let it sit for several minutes, then check the oil level on the dipstick. If necessary, add more oil.
Adding Engine Coolant
RESERVE TANK
RESERVE TANK
Improper disposal of engine oil can be harmf ul to the environment. If you change your own oil, please dispose of the used oil properly. Put it in a sealed container and take it to a recycling center. Do not discard it in a trash bin or dump it on the ground.
228
Except U.S. Si If the coolant level in the reserve tank is at or below the MIN line, add coolant to bring it up to the MAX line. Inspect the cooling system for leaks.
U.S. Si
Always use Honda Long-life Anti- freeze/Coolant Type 2. This coolant is pre-mixed with 50 percent antifreeze and 50 percent water. Never add straight antifreeze or plain water.
Main MenuTable of ContentsstIf Honda antifreeze/coolant is not available, you may use another major-brand non-silicate coolant as a temporary replacement. Make sure it is a high-quality coolant recommended for aluminum engines. Continued use of any non-Honda coolant can result in corrosion, causing the cooling system to malfunction or fail. Have the cooling system flushed and refilled with Honda antifreeze/coolant as soon as possible.
If the reserve tank is completely empty, you should also check the coolant level in the radiator.
Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.
Always let the engine and radiator cool down before removing the radiator cap.
Engine Coolant
RADIATOR CAP
Except U.S. Si
1.
Make sure the engine and radiator are cool.
2.
Relieve any pressure in the cooling system by turning the radiator cap counterclockwise, without pressing down.
CONTINUED
229
Main MenuTable of ContentsstEngine Coolant
RADIATOR CAP
RESERVE TANK
RESERVE TANK
U.S. Si 3.
Remove the radiator cap by pushing down and turning counterclockwise.
230
Except U.S. Si The coolant level should be up to 4. the base of the filler neck. Add coolant if it is low.
Pour the coolant slowly and carefully so you do not spill any. Clean up any spill immediately; it could damage components in the engine compartment.
5.
Put the radiator cap back on, and tighten it fully.
U.S. Si 6.
Pour coolant into the reserve tank. Fill it to halfway between the MAX and MIN marks. Put the cap back on the reserve tank.
Do not add any rust inhibitors or other additives to your vehicle’s cooling system. They may not be compatible with the coolant or engine components.
Main MenuTable of ContentsstCheck the fluid level in the windshield washer reservoir at least monthly during normal use.
LEVEL GAUGE
LEVEL GAUGE
U.S. Si
Except U.S. Si
Check the fluid level by removing the cap and looking at the level gauge.
OnCanadianmodels: level indicator comes on when the level is low (see page
The low washer
64
).
Fill the reservoir with a good-quality windshield washer fluid. This increases the cleaning capability and prevents freezing in cold weather.
Windshield Washers
When you refill the reservoir, clean the edges of the windshield wiper blades with windshield washer fluid on a clean cloth. This will help to condition the blade edges.
Do not use engine antif reeze or a vinegar/water solution in the windshield washer reservoir. Antif reeze can damage your vehicle’s paint, while a vinegar/water solution can damage the windshield washer pump. Use only commercially-available windshield washer f luid.
231
Main MenuTable of ContentsstTransmission Fluid
Automatic Transmission
DIPSTICK
UPPER MARK LOWER MARK
Check the fluid level with the engine at normal operating temperature. 1.
Park the vehicle on level ground. Run the engine until the radiator fan comes on once, and then goes off. Turn off the engine. For accurate results, wait about 60 seconds before going to step 2, but don’t wait longer than 90 seconds.
2.
3.
4.
Remove the dipstick (yellow loop) from the transmission, and wipe it with a clean cloth.
Insert the dipstick all the way into the transmission securely as shown in the illustration.
Remove the dipstick and check the fluid level. It should be between the upper and lower marks.
232
5.
If the level is below the lower mark, add fluid into the dipstick hole to bring it to the level between the upper and lower marks.
Pour the fluid slowly and carefully so you do not spill any. Clean up any spills immediately; it could damage components in the engine compartment.
Always use Honda ATF-Z1
(automatic transmission fluid). If
it’s not available, you may use a
DEXRON III automatic
transmission fluid as a temporary
replacement. However, continued
use can affect the shift quality.
Have the transmission flushed and
refilled with Honda ATF-Z1 by
your dealer as soon as it is
convenient.
Main MenuTable of Contentsst6.
Insert the dipstick all the way back into the transmission securely as shown in the illustration.
The automatic transmission should be drained and refilled with new fluid when this service is indicated by a maintenance message on the information display.
If you are not sure how to add fluid, contact your dealer.
Automatic Transmission Fluid, Manual Transmission Fluid
Manual Transmission Fluid
FILLER BOLT
FILLER BOLT
Correct Level
Except U.S. Si
Check the fluid level with the transmission at normal operating temperature and the vehicle sitting on level ground. Remove the transmission filler bolt, and carefully feel inside the bolt hole with your finger. The fluid level should be up to the edge of the bolt hole. If it is not, add Honda Manual Transmission Fluid (MTF) until it starts to run out of the hole. Reinstall the filler bolt, and tighten it securely.
Correct Level
U.S. Si
If Honda MTF is not available, you
may use an SAE 10W-30 or 10W-40
viscosity motor oil with the API
Certification seal that says ‘‘FOR
GASOLINE ENGINES’’ as a
temporary replacement. However,
motor oil does not contain the proper
additives, and continued use can
cause stiffer shifting. Replace as
soon as it is convenient.
CONTINUED
233
Main MenuTable of ContentsstManual Transmission Fluid, Brake and Clutch Fluid
The manual transmission should be drained and refilled with new fluid when this service is indicated by a maintenance message on the information display.
If you are not sure how to check and add fluid, contact your dealer.
234
Brake and Clutch Fluid Check the brake fluid level in the reservoirs monthly.
Replace the brake fluid according to the time recommendations in the maintenance minder schedule.
Always use Honda Heavy Duty
Brake Fluid DOT 3. If it is not
available, you should use only DOT 3
or DOT 4 fluid, from a sealed
container, as a temporary
replacement.
Using any non-Honda brake fluid can cause corrosion and decrease the life of the system. Have the brake system flushed and refilled with Honda Heavy Duty Brake Fluid DOT 3 as soon as possible.
Brake fluid marked DOT 5 is not compatible with your vehicle’s braking system and can cause extensive damage.
Brake System
MAX
MIN
The fluid level should be between the MIN and MAX marks on the side of the reservoir. If the level is at or below the MIN mark, your brake system needs attention. Have the brake system inspected for leaks or worn brake pads.
Main MenuTable of ContentsstClutch Fluid ManualTransmissiononly
UPPER LEVEL
Brake and Clutch Fluid, Power Steering Fluid
Power Steering Fluid
compartment.
MAX
MIN
The fluid level should be between the MIN and MAX marks on the side of the reservoir. If it is not, add brake fluid to bring it up to that level. Use the same fluid specified for the brake system.
A low fluid level can indicate a leak in the clutch system. Have this system inspected as soon as possible.
LOWER LEVEL
AllmodelsexceptU.S.Si Check the level on the side of the reservoir when the engine is cold. The fluid should be between the UPPER LEVEL and LOWER LEVEL. If not add power steering fluid to the UPPER LEVEL mark.
Pour the fluid slowly and carefully so you do not spill any. Clean up any spill immediately; it could damage components in the engine
Always use Honda Power Steering Fluid. You may use another power steering fluid as an emergency replacement, but have the power steering system flushed and refilled with Honda PSF as soon as possible.
A low power steering fluid level can indicate a leak in the system. Check the fluid level frequently, and have the system inspected as soon as possible.
Turning the steering wheel to f ull lef t or right lock and holding it there can damage the power steering pump.
235
Main MenuTable of ContentsstLights
Headlight Aiming The headlights were properly aimed when your vehicle was new. If you regularly carry heavy items in the trunk or pull a trailer, readjustment may be required. Adjustments should be performed by your dealer or other qualified mechanic.
Replacing a Headlight Bulb Your vehicle has halogen headlight bulbs. When replacing a bulb, handle it by its base, and protect the glass from contact with your skin or hard objects. If you touch the glass, clean it with denatured alcohol and a clean cloth.
HighBeamHeadlight
Halogen headlight bulbs get very hot when lit. Oil, perspiration, or a scratch on the glass can cause the bulb to overheat and shatter.
1.
To change the headlight bulb on the driver’s side, remove the engine coolant reserve tank by pulling it out of its holder.
236
Main MenuTable of Contentsst4.
5.
Insert the new bulb into the hole, and turn it one-quarter turn clockwise to lock it in place.
Push the electrical connector back onto the bulb. Make sure it is on all the way.
6.
Turn on the headlights to test the new bulb.
7.
If you replaced a headlight bulb on the driver’s side, reinstall the engine coolant reserve tank.
BULB
TAB
2.
Remove the bulb by turning it one- quarter turn counterclockwise.
3.
Remove the electrical connector from the bulb by pushing on the tab and pulling the connector down.
LowBeamHeadlight
Lights
HOLDING CLIP
1.
2.
To change the bulb on the driver’s side, start the engine, turn the steering wheel all the way to the right, then turn off the engine. To change the bulb on the passenger’s side, turn the steering wheel to the left.
Use a flat-tipped screwdriver to remove the two holding clips from the inner fender, and pull the inner fender cover back.
CONTINUED
237
Main MenuTable of ContentsstLights
SOCKET
TAB
3.
Remove the electrical connector from the bulb by pushing on the tab and pulling the connector down.
4.
Remove the bulb by turning it one- quarter turn counterclockwise.
238
5.
6.
Insert the new bulb into the hole, and turn it one-quarter turn clockwise to lock it in place.
Push the electrical connector back onto the bulb. Make sure it is on all the way.
7.
Turn on the headlights to test the new bulb.
8.
Reinstall the inner fender cover. Then reinstall the holding clips, and lock them in place by pushing on their centers.
Replacing the Front Side Marker/ Parking/Turn Signal Light Bulb
HOLDING CLIP
1.
To change the bulb on the driver’s side, start the engine, turn the steering wheel all the way to the right, then turn off the engine. To change the bulb on the passenger’s side, turn the steering wheel to the left.
Main MenuTable of Contentsst4.
Remove the bulb from the socket by pushing the bulb in and turning it counterclockwise until it unlocks.
5.
Install the new bulb in the socket. Turn it clockwise to lock it in place.
6.
Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place.
7.
Test the lights to make sure the new bulb is working.
8.
Reinstall the inner fender cover. Then reinstall the holding clips, and lock them in place by pushing on their centers.
Replacing Rear Bulbs (In Fenders)
Lights
FASTENER
FASTENER
1.
Open the trunk.
Remove the screw from the center of each fastener on the side of the trunk lining. Pull the lining back.
2.
Determine which of the four bulbs is burned out: stop/taillight, back- up light, turn signal, or side marker.
CONTINUED
239
2.
Use a flat-tipped screwdriver to remove the two holding clips from the inner fender, and pull the inner fender cover back.
3.
Remove the socket from the headlight assembly by turning it one-quarter turn counterclockwise.
Main MenuTable of ContentsstLights
BULBS
Replacing Rear Bulbs (in Trunk Lid)
BULB
SOCKETS
SOCKETS
BULB
3.
Remove the socket by turning it one-quarter turn counterclockwise.
6.
Test the lights to make sure the new bulb is working.
4.
5.
Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms.
Reinstall the socket into the light assembly by turning it clockwise until it locks.
7.
8.
Reinstall the trunk lining. Make sure it is installed under the edge of the trunk seal.
Put the fasteners into the holes on the side of the trunk lining. Reinstall the screws.
FASTENERS
1.
Open the trunk.
2.
OnLX,EXandU.S.Simodels Remove the screw from the center of each fastener on the trunk lid trim. Pull the trim back.
240
Main MenuTable of ContentsstBULB
SOCKET Remove the socket by turning it 3. one-quarter turn counterclockwise.
4.
5.
Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms.
Insert the socket back into the light assembly. Turn it clockwise to lock it in place.
6.
Test the lights to make sure the new bulb is working.
7.
8.
OnLX,EXandU.S.Simodels Push the trunk lid trim back into position.
Put the fasteners into the holes on the trunk lid trim. Reinstall the screws.
Lights
Replacing a High-mount Brake Light Bulb
BULB
SOCKET
1.
2.
3.
Open the trunk, and remove the socket from the light assembly by turning it one-quarter turn counter- clockwise. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. Reinstall the socket. Turn it clockwise until it locks. Make sure the new bulb is working.
241
Main MenuTable of ContentsstCleaning the Seat Belts, Floor Mats, Dust and Pollen Filter
Cleaning the Seat Belts
Floor Mats
LOOP
If your seat belts get dirty, use a soft brush with a mixture of mild soap and warm water to clean them. Do not use bleach, dye, or cleaning solvents. Let the belts air dry before you use the vehicle. Dirt build-up in the loops of the seat belt anchors can cause the belts to retract slowly. Wipe the insides of the loops with a clean cloth dampened in mild soap and warm water or isopropyl alcohol.
242
Ifequipped The floor mats that came with your vehicle hook over the floor mat anchors. This keeps them from sliding forward and possibly interfering with vehicle operation.
If you remove the driver’s floor mat, make sure to re-anchor it when you put it back in your vehicle.
If you use non-Honda floor mats, make sure they fit properly and that they can be used with the floor mat anchors. Do not put additional floor mats on top of the anchored mats.
Dust and Pollen Filter OnmodelswithA/C This filter removes the dust and pollen that is brought in from the outside through the heating and cooling system.
Have your dealer replace the filter
when this service is indicated by a
maintenance message on the
information display. It should be
replaced every 15,000 miles (24,000
km) if you drive primarily in urban
areas that have high concentrations
of soot in the air, or if the flow from
the heating and cooling system
becomes less than usual.
Main MenuTable of ContentsstCheck the condition of the wiper blades at least every 6 months. Replace them if you find signs of cracking in the rubber, and areas that are getting hard or if they leave streaks and unwiped areas when used.
Wiper Blades
COVER
WIPER ARMS
To replace a wiper blade:
1.
Lift the wiper arm off the windshield, raising the driver’s side first, then the passenger’s side.
Do not open the hood when the wiper arms are raised, or you will damage the hood and wiper arms.
2.
Remove the cover, by squeezing the two tabs and pulling it straight out.
CONTINUED
243
Main MenuTable of ContentsstWiper Blades
TAB
BLADE ASSEMBLY
REINFORCEMENT STRIP
WIPER BLADE
4.
Remove the blade from the blade assembly:
Find the side of the blade labeled ‘‘LOCK.’’ This is the side you pull out. Pull back the end of the blade assembly on the ‘‘LOCK’’ side of the blade. Then grab the end of the blade, and slide it out.
5.
Examine the new wiper blades. If they have no plastic or metal reinforcement along the back edge, remove the metal reinforcement strips from the old wiper blade, and install them in the slots along the edge of the new blade.
3.
Disconnect the blade assembly from the wiper arm:
Press and hold the lock tab. Slide the blade assembly toward the lock tab until it releases from the wiper arm.
When replacing a wiper blade, make sure not to drop the wiper blade or wiper arm down on the windshield.
244
Main MenuTable of ContentsstWiper Blades, Tires
Tires To safely operate your vehicle, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated.
Inflation Guidelines Keeping the tires properly inflated provides the best combination of handling, tread life, and riding comfort.
The following pages give more detailed information on how to take care of your tires and what to do when they need to be replaced.