2004 Honda Civic Sedan Owners Manual

according to the child seat maker’s instructions. A child who is not properly secured in a child seat can be seriously injured in a crash.

Driver and Passenger Safety

37

Main MenustTable of Contents０３／０６／０４　１４：１８：０６　３１Ｓ５Ａ６３０　００４１　

Installing a Child Seat

Installing a Child Seat Using LATCH Your vehicle is equipped with LATCH (Lower Anchors and Tethers for Children) at the outer rear seats. The lower anchors are located between the seat-back and seat bottom, and are to be used only with a child seat designed for use with LATCH.

MARKS

LOWER ANCHORS

The location of each lower anchor is marked with a small circle above the point.

2.

38

Driver and Passenger Safety

On Canadian models, each location mark has the symbol shown above.

To install a LATCH-compatible child seat: 1.

Move the seat belt buckle or tongue away from the lower anchors. Make sure there are no objects near the anchors that could prevent a secure connection between the child seat and anchors.

Main MenustTable of Contents０３／０６／０４　１４：１８：１６　３１Ｓ５Ａ６３０　００４２　

Installing a Child Seat

TETHER STRAP HOOK

ANCHORAGE POINT

6.

Attach the tether strap hook to the tether anchor, then tighten the strap as instructed by the child seat maker.

7.

Push and pull the child seat forward and from side to side to verify that it is secure.

Driver and Passenger Safety

39

Rigid type

3.

Place the child seat on the vehicle seat and attach the seat to the lower anchors according to the child seat maker’s instructions.

Some LATCH-compatible seats have a rigid-type connection as shown above.

Flexible type Other LATCH-compatible seats have a flexible-type connection as shown above.

4.

5.

Whatever type you have, follow the child seat maker’s instructions for adjusting or tightening the fit.

Lift the rear head restraint, then route the tether strap over the seat-back between the legs of the head restraint, making sure the strap is not twisted.

Main MenustTable of Contents０３／０６／０４　１４：１８：２５　３１Ｓ５Ａ６３０　００４３　

Installing a Child Seat

Installing a Child Seat with a Lap/ Shoulder Belt When not using the LATCH system, all child seats must be secured to the vehicle with the lap part of a lap/ shoulder belt.

In addition, the lap/shoulder belts in the back seating positions, and in the front passenger seat, have a locking mechanism that must be activated to secure a child seat.

1.

With the child seat in the desired seating position, route the belt through the child seat according to the seat maker’s instructions, then insert the latch plate into the buckle.

2.

3.

To activate the lockable retractor, slowly pull the shoulder part of the belt all the way out until it stops, then let the belt feed back into the retractor.

After the belt has retracted, tug on it. If the belt is locked, you will not be able to pull it out. If you can pull the belt out, it is not locked and you will need to repeat these steps.

40

Driver and Passenger Safety

Main MenustTable of Contents０３／０６／０４　１４：１８：３７　３１Ｓ５Ａ６３０　００４４　

Installing a Child Seat

Installing a Child Seat with a Tether

COVER

ANCHORAGE POINT

A child seat with a tether can be installed in any seating position in the back seat, using one of the anchorage points shown above.

Since a tether can provide additional security to the lap/shoulder belt installation, we recommend using a tether whenever one is required or available. (Tethers are required in Canada.)

Driver and Passenger Safety

41

4.

After confirming that the belt is locked, then grab the shoulder part of the belt near the buckle and pull up to remove any slack from the lap part of the belt. Remember, if the lap part of the belt is not tight, the child seat will not be secure.

To remove slack, it may help to put weight on the child seat, or push on the back of the seat while pulling up on the belt.

5.

Push and pull the child seat forward and from side to side to verify that it is firmly secured. If the child seat is not secure, unlatch the belt, allow it to retract fully, then repeat these steps.

To deactivate the locking mechanism and remove a child seat, unlatch the buckle, unroute the seat belt, and let the belt fully retract.

Main MenustTable of Contents０３／０６／０４　１４：１８：５０　３１Ｓ５Ａ６３０　００４５　

Installing a Child Seat, Protecting Larger Children

Using an Outer Anchorage Point

TETHER STRAP HOOK

Using the Center Anchorage Point

ANCHORAGE POINT

Protecting Larger Children When a child reaches the recommended weight or height limit for a forward-facing child seat, the child should sit in a back seat on a booster and wear a lap/shoulder belt. The following pages give instructions on how to check proper seat belt fit, what kind of booster seat to use if one is needed, and important precautions for a child who must sit in front.

1.

2.

3.

34

), lift the head restraint, then

After securing the child seat in the desired position (see pages and 35
route the tether strap over the top of the seat-back and through the head restraint legs. Lift the anchor point lid, then attach the tether strap hook to the anchor, making sure the strap is not twisted. Tighten the strap according to the seat maker’s instructions.

42

Driver and Passenger Safety

1.

2.

After properly securing the child seat with the lap/shoulder belt (see page ), route the tether strap over the top of the seat-back.

40

Attach the tether strap hook to the anchor, making sure the strap is not twisted, then tighten the strap according to the seat-maker’s instructions.

Allowing a larger child age 12 or under to sit in front can result in injury or death if the passenger’s front airbag inflates.

If a larger child must ride in front, move the vehicle seat as far back as possible, use a booster seat if needed, have the child sit up properly and wear the seat belt properly.

Main MenustTable of Contents０３／０６／０４　１４：１９：０５　３１Ｓ５Ａ６３０　００４６　

3.

Does the shoulder belt cross between the child’s neck and arm?

4.

Is the lap part of the belt as low as possible, touching the child’s thighs?

5.

Will the child be able to stay seated like this for the whole trip?

If you answer yes to all these questions, the child is ready to wear the lap/shoulder belt correctly. If you answer no to any question, the child needs to ride on a booster seat.

Checking Seat Belt Fit

To determine if a lap/shoulder belt properly fits a child, have the child put on the seat belt, then ask yourself:

1.

Does the child sit all the way back against the seat?

2.

Do the child’s knees bend comfortably over the edge of the seat?

Protecting Larger Children

Using a Booster Seat

A child who has outgrown a forward- facing child seat should ride in a back seat and use a booster seat until the lap/shoulder belt fits them properly without the booster.

CONTINUED

Driver and Passenger Safety

43

Main MenustTable of Contents０３／０６／０４　１４：１９：１５　３１Ｓ５Ａ６３０　００４７　

Protecting Larger Children

Some states also require children to use a booster until they reach a given age or weight (e.g., 6 years or 60 lbs). Be sure to check current laws in the state or states where you intend to drive.

Booster seats can be high-back or low-back. Whichever style you select, make sure the booster meets federal safety standards and that you follow the booster seat maker’s instructions.

If a child who uses a booster must be in front, move the vehicle seat as far back as possible and be sure the child is wearing the seat belt properly.

44

Driver and Passenger Safety

A child may continue using a booster seat until the tops of their ears are even with the top of the vehicle’s or booster’s seat-back. A child of this height should be tall enough to use the lap/shoulder belt without a booster.

WhenCanaLargerChildSitinFront The National Highway Traffic Safety Administration and Transport Canada recommend that all children age 12 and under be properly restrained in the back seat.

If the passenger’s front airbag inflates, and it inflates in a moderate to severe frontal collision, the airbag can cause serious injuries to a child who is unrestrained, improperly restrained, sitting too close to the airbag, or out of position.

The side airbag also poses risks. If any part of a larger child’s body is in the path of a deploying side airbag, the child could receive possibly serious injuries.

Main MenustTable of Contents０３／０６／０４　１４：１９：３０　３１Ｓ５Ａ６３０　００４８　

Of course, children vary widely. And while age may be one indicator of when a child can safely ride in the front. There are other important factors you should consider.

Maturity To safely ride in front, a child must be able to follow the rules, including sitting properly, and wearing the seat belt properly throughout ride.

PhysicalSize Physically, a child must be large enough for the lap/shoulder belt to properly fit (see page belt does not fit properly, with or without the child sitting on a booster, the child should not sit in the front.

). If the seat

43

If you decide that a child can safely ride up front, be sure to:

Carefully read the owner’s manual and make sure you understand all seat belt instructions and all safety information.

Move the vehicle seat to the rear- most position.

Have the child sit up straight, back against the seat, and feet on or near the floor.

Check that the child’s seat belt is properly and securely positioned and secured.

Supervise the child. Even mature children sometimes need to be reminded to fasten the seat belts or sit properly.

Protecting Larger Children

Additional Safety Precautions Donotletachildwearaseatbelt This could result in acrosstheneck. serious neck injuries during a crash.

Donotletachildputtheshoulder partofaseatbeltbehindthebackor underthearm. very serious injuries during a crash. It also increases the chance that the child will slide under the belt in a crash and be injured.

This could cause

Twochildrenshouldneverusethe If they do, they could sameseatbelt. be very seriously injured in a crash.

Donotputanyaccessoriesonaseat Devices intended to improve a belt. child’s comfort or reposition the shoulder part of a seat belt can make the belt less effective, and increase the chance of serious injury in a crash.

Driver and Passenger Safety

45

Main MenustTable of Contents０３／０６／０４　１４：１９：４０　３１Ｓ５Ａ６３０　００４９　

Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and even kill you.

Avoid any enclosed areas or activities that expose you to carbon monoxide.

High levels of carbon monoxide can collect rapidly in enclosed areas, such as a garage. Do not run the engine with the garage door closed. Even with the door open, run the engine only long enough to move the vehicle out of the garage.

With the trunk lid open, air flow can pull exhaust gas into your vehicle’s interior and create a hazardous condition. If you must drive with the trunk lid open, open all the windows and set the heating and cooling system as shown below.

If you must sit in your parked vehicle, even in an unconfined area, with the engine running, adjust the heating and cooling system as follows:

1. 2. 3. 4.

Select the Fresh Air mode. Select the Turn the fan on high speed. Set the temperature control to a comfortable setting.

mode.

Carbon Monoxide Hazard

Your vehicle’s exhaust contains carbon monoxide gas. You should have no problem with carbon monoxide entering the vehicle in normal driving if you maintain your vehicle properly. Have the exhaust system inspected for leaks whenever:

The vehicle is raised for an oil change. You notice a change in the sound of the exhaust. The vehicle was in an accident that may have damaged the under- side.

46

Driver and Passenger Safety

Main MenustTable of Contents０３／０６／０４　１４：１９：５９　３１Ｓ５Ａ６３０　００５０　

Safety Labels

These labels are in the locations shown. They warn you of potential hazards that could cause serious injury. Read these labels carefully. If a label comes off or becomes hard to read, contact your Honda dealer for a replacement.

DASHBOARD U.S.modelsonly

SUN VISOR U.S.models

Canadianmodels

RADIATOR CAP

Driver and Passenger Safety

47

Main MenustTable of Contents０３／０６／０４　１４：２０：０８　３１Ｓ５Ａ６３０　００５１　

Safety Labels

HOOD Onmodelswithoutsideairbags

Onmodelswithsideairbags

48

Driver and Passenger Safety

Main MenustTable of Contents０３／０６／０４　１４：２０：１３　３１Ｓ５Ａ６３０　００５２　

Instruments and Controls

This section gives information about the controls and displays that contribute to the daily operation of your Honda. All the essential controls are within easy reach.

. 50
........................... Control Locations . 51
............................ Instrument Panel Instrument Panel Lights ................ . 54
.. Maintenance Required Indicator . 58
. 59
............................................. Gauges ............... . 59
. 59
.................................. ................... . 60

Odometer/Trip Meter Fuel Gauge Temperature Gauge

Controls Near the Steering

Wheel

........................................... . 61
Windshield Wipers and Washers . 62
. 63
Turn Signal and Headlights ........... . 64
Instrument Panel Brightness ........ . 65
Hazard Warning Light ................... . 65
Rear Window Defogger ................. .......... Steering Wheel Adjustment . 66
. 67
Keys and Locks ............................... . 68
Immobilizer System ........................ . 69
Ignition Switch ................................ ...................................... Door Locks . 70
. 70
...................... . 70
.............. . 71
........................................... . 71
........ ....................... . 72
. 74
.................................................

Power Door Locks Childproof Door Locks Trunk Emergency Trunk Opener

Remote Transmitter Seats

Power Windows Moonroof Mirrors Parking Brake Interior Lights Interior Convenience Items

.............................. ......................................... ............................................. ................................. ................................. ........... ....................... .......... .................................... ...............

Beverage Holders Accessory Power Sockets Glove Box Console Compartment

. 78
. 80
. 80
. 82
. 83
. 84
. 85
. 85
. 85
. 85

Instruments and Controls

49

Main Menust０３／０６／０４　１４：２０：２０　３１Ｓ５Ａ６３０　００５３　

Control Locations

MOONROOF CONTROLS (P. 80)

MIRROR CONTROLS (P. 81)

HEATING/COOLING CONTROLS (P. 88)

POWER DOOR LOCK SWITCH (P. 70)

CRUISE CONTROL MASTER SWITCH (P. 107)

POWER WINDOW SWITCHES (P. 78)

AUDIO SYSTEM (P. 92) DIGITAL CLOCK (P. 106)

FUEL FILL DOOR RELEASE (P. 113) TRUNK RELEASE (P. 71)

HOOD RELEASE HANDLE (P. 114)

CRUISE CONTROL SWITCHES (P. 107)

AT model is shown.

50

Instruments and Controls

Main MenustTable of Contents０３／０６／０４　１４：２０：２９　３１Ｓ５Ａ６３０　００５４　

LX, U.S. EX, and Canadian Si models

ANTI-LOCK BRAKE SYSTEM INDICATOR (P. 55)

CRUISE CONTROL INDICATOR (P. 56)

HIGH BEAM INDICATOR (P. 56)

CHARGING SYSTEM INDICATOR (P. 55, 182)

LOW OIL PRESSURE INDICATOR (P. 55, 182)

Instrument Panel

SEAT BELT REMINDER LIGHT (P. 54)

PARKING BRAKE AND BRAKE SYSTEM INDICATOR (P. 55)

TRUNK-OPEN INDICATOR (P. 56)

MAINTENANCE REQUIRED INDICATOR (P. 58)

LOW FUEL INDICATOR (P. 56)

MALFUNCTION INDICATOR LAMP (P. 183)

SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR (P. 54)

IMMOBILIZER SYSTEM INDICATOR (P. 57)

SHIFT LEVER POSITION INDICATOR (P. 128)

SIDE AIRBAG CUTOFF INDICATOR (P. 54)

The U.S. instrument panel is shown. Differences for the Canadian models are noted in the text.

Instruments and Controls

51

Main MenustTable of Contents０３／０６／０４　１４：２０：３５　３１Ｓ５Ａ６３０　００５５　

Instrument Panel

Canadian DX model

SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR (P. 54)

IMMOBILIZER SYSTEM INDICATOR (P. 57)

LOW OIL PRESSURE INDICATOR (P. 55, 182)

CHARGING SYSTEM INDICATOR (P. 55, 182)

TRUNK-OPEN INDICATOR (P. 56) SIDE AIRBAG CUTOFF INDICATOR (P. 54)

DAYTIME RUNNING LIGHTS INDICATOR (P. 57)

WASHER LEVEL INDICATOR (P. 56)

LOW FUEL INDICATOR (P. 56)

PARKING BRAKE AND BRAKE SYSTEM INDICATOR (P. 55)

MALFUNCTION INDICATOR LAMP (P. 183)

HIGH BEAM INDICATOR (P. 56)

SEAT BELT REMINDER LIGHT (P. 54)

MAINTENANCE REQUIRED INDICATOR (P. 58)

52

Instruments and Controls

Main MenustTable of Contents０３／０６／０４　１４：２０：４３　３１Ｓ５Ａ６３０　００５６　

Instrument Panel

U.S. DX model

SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR (P. 54)

TRUNK-OPEN INDICATOR (P. 56)

SIDE AIRBAG CUTOFF INDICATOR (P. 54)

IMMOBILIZER SYSTEM INDICATOR (P. 57)

LOW OIL PRESSURE INDICATOR (P. 55, 182)

CHARGING SYSTEM INDICATOR (P. 55, 182)

MALFUNCTION INDICATOR LAMP (P. 183)

HIGH BEAM INDICATOR (P. 56)

SEAT BELT REMINDER LIGHT (P. 54)

MAINTENANCE REQUIRED INDICATOR (P. 58)

LOW FUEL INDICATOR (P. 56)

PARKING BRAKE AND BRAKE SYSTEM INDICATOR (P. 55)

Instruments and Controls

53

Main MenustTable of Contents０３／０６／０４　１４：２０：５４　３１Ｓ５Ａ６３０　００５７　

Supplemental Restraint System Indicator

This light comes on when you turn the ignition switch to ON (II). If it comes on at any other time, it indicates a potential problem with your front airbags or automatic seat belt tensioners. On models equipped with side airbags, this indicator will also alert you to a potential problem with your side airbags or passenger’s side airbag automatic cutoff system. For complete information, see page 26

Side Airbag Cutoff Indicator

Onlyonmodelsequippedwithside airbags This indicator comes on when you turn the ignition switch ON (II). If it comes on at any other time, it indicates that the passenger’s side airbag has automatically shut off. For complete information, see page .27

Instrument Panel Lights

The instrument panel has many indicators to give you important information about your vehicle.

Seat Belt Reminder Light

If you turn the ignition switch to ON (II) without fastening your seat belt, the beeper starts to sound, and the indicator starts to blink. The beeper stops sounding several seconds later but the indicator will remain lit.

If you drive without your seat belt fastened, the indicator remains on and the beeper will sound every few seconds.

54

Instruments and Controls

Main MenustTable of Contents０３／０６／０４　１４：２１：０６　３１Ｓ５Ａ６３０　００５８　

Instrument Panel Lights

Charging System Indicator

If this indicator comes on when the engine is running, the battery is not being charged. For complete information, see page

182

Low Oil Pressure Indicator

The engine can be severely damaged if this light flashes or stays on when the engine is running. For complete information, see page

182

U.S.

Canada

Parking Brake and Brake System Indicator

This indicator has two functions:

1.

2.

It comes on when you turn the ignition switch to ON (II). It is a reminder to check the parking brake. Driving with the parking brake not fully released can damage the brakes and tires.

If it remains lit after you have fully released the parking brake while the engine is running, or if it comes on while driving, there could be a problem with the brake system. For complete information, see page

184

Anti-lock Brake System (ABS) Indicator

OnlyonmodelsequippedwithABS(see page )133
This indicator normally comes on for a few seconds when you turn the ignition switch to ON (II), and when the ignition switch is turned to START (III). If it comes on at any other time, there is a problem in the ABS. If this happens, have your vehicle checked at a dealer. With this light on, your vehicle still has normal braking ability but no anti- lock. For complete information, see page

133

Instruments and Controls

55

Main MenustTable of Contents０３／０６／０４　１４：２１：２３　３１Ｓ５Ａ６３０　００５９　

High Beam Indicator

Trunk-open Indicator

This indicator comes on with the high beam headlights. See page 63
controls.

for information on the headlight

On Canadian models, this indicator comes on with reduced brightness when the Daytime Running Lights (DRL) are on (see page

63

).

Cruise Control Indicator

OnlyonmodelsequippedwithCruise ControlSystem This lights when you set the cruise control. See page on operating the cruise control.

for information

107

This light comes on if the trunk lid is not closed tightly.

Low Fuel Indicator

This indicator comes on as a reminder that you must refuel soon.

Washer Level Indicator

Canadianmodelsonly This indicator comes on when the washer fluid level is low. Add washer fluid when you see this indicator come on (see page

148

).

Instrument Panel Lights

Malfunction Indicator Lamp 183

See page

Turn Signal and Hazard Warning Indicators

The left or right turn signal indicator blinks when you signal a lane change or turn. If the indicators do not blink or blinks rapidly, it usually means one of the turn signal bulbs is burned out (see page the bulb as soon as possible, since other drivers cannot see that you are signaling.

). Replace

155

When you turn on the Hazard Warning switch, both turn signal indicators blink. All turn signals on the outside of the vehicle should flash.

56

Instruments and Controls

Main MenustTable of Contents０３／０６／０４　１４：２１：３２　３１Ｓ５Ａ６３０　００６０　

Instrument Panel Lights

‘‘Daytime Running Lights’’ Indicator

Canadianmodelsonly This indicator lights when you turn the ignition switch to ON (II) with the headlight switch off and the parking brake set. It should go off if you turn on the headlights or release the parking brake. If it comes on at any other time, it means there is a problem with the DRL. There may also be a problem with the high beam headlights.

Immobilizer System Indicator

This light comes on for a few sec- onds when you turn the ignition switch ON (II). It will then go off if you have inserted a properly-coded ignition key. If it is not a properly- coded key, the light will blink and the engine will not start (see page 68

).

This light also blinks several times when you turn the ignition switch from ON (II) to ACCESSORY (I) or LOCK (0).

Instruments and Controls

57

Main MenustTable of Contents０３／０６／０４　１４：２１：４３　３１Ｓ５Ａ６３０　００６１　

Maintenance Required Indicator

Between 8,000 miles (12,800 km) and 10,000 miles (16,000 km), it will light for two seconds when you first turn the ignition switch to ON (II), and then flash for ten seconds.

If you exceed 10,000 miles (16,000
km) without having the scheduled maintenance performed, this light will remain on as a constant reminder.

Your dealer will reset this indicator after completing the scheduled maintenance. If this maintenance is not done by a Honda dealer, reset the light as follows.

1.

Turn off the engine.

2.

Press and hold the Select/Reset knob in the instrument panel, then turn the ignition switch to ON (II).

3.

Hold the knob for about ten seconds until the light goes off.

Maintenance Required Indicator

This indicator reminds you that it is time to take your vehicle in for scheduled maintenance. Refer to the Maintenance Schedules for Normal and Severe Driving Conditions on pages

and

140

139

For the first 8,000 miles (12,800 km) after the Maintenance Required Indicator is reset, it will come on for two seconds when you turn the ignition switch to ON (II).

58

Instruments and Controls

Main MenustTable of Contents０３／０６／０４　１４：２１：５５　３１Ｓ５Ａ６３０　００６２　

LX, U.S. EX, and Canadian Si models

SPEEDOMETER TEMPERATURE GAUGE

TACHOMETER

FUEL GAUGE

The U.S. instrument panel is shown

ODOMETER/TRIP METER

SELECT/RESET KNOB

Odometer/Trip Meter The odometer shows the total dis- tance your vehicle has been driven. It measures miles in the U.S. models and kilometers in the Canadian models.

It is illegal under U.S. federal law and Canadian provincial regulations to disconnect, reset, or alter the odometer with the intent to change

the number of miles or kilometers indicated.

The odometer and the trip meters use the same display. Switch these displays by pressing the Select/ Reset knob.

The trip meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it.

Gauges

There are two trip meters: Trip A and Trip B. Each trip meter works independently, so you can keep track of two different distances.

To reset a trip meter, display it and then press and hold the Select/Reset knob until the number resets to ‘‘0.0’’.

Fuel Gauge This shows how much fuel you have. It may show slightly more or less than the actual amount. The needle returns to the bottom after you turn off the ignition.

Avoid driving with an extremely low fuel level. Running out of fuel could cause the engine to misfire, damaging the catalytic converter.

Instruments and Controls

59

Main MenustTable of Contents０３／０６／０４　１４：２２：０５　３１Ｓ５Ａ６３０　００６３　

Gauges

U.S. DX model

TEMPERATURE GAUGE

FUEL GAUGE

SPEEDOMETER

ODOMETER/TRIP METER

SELECT/RESET KNOB

Canadian DX model

TEMPERATURE GAUGE

FUEL GAUGE

TACHOMETER

SPEEDOMETER

ODOMETER/TRIP METER

SELECT/RESET KNOB

60

Instruments and Controls

Temperature Gauge This shows the temperature of the engine’s coolant. During normal operation, the pointer should rise to about the middle of the gauge. In severe driving conditions, the pointer may rise to the upper zone. If it reaches the red (Hot) mark, pull safely to the side of the road. Turn to page precautions on checking the engine’s cooling system.

for instructions and

179

Main MenustTable of Contents０３／０６／０４　１４：２２：０９　３１Ｓ５Ａ６３０　００６４　

Controls Near the Steering Wheel

MOONROOF

HEADLIGHTS/ TURN SIGNALS

HAZARD WARNING BUTTON

WINDSHIELD WIPERS/WASHERS

CRUISE CONTROL MASTER SWITCH

MIRROR CONTROLS

HORN

＊

REAR WINDOW DEFOGGER

TILT ADJUSTMENT

CRUISE CONTROL SWITCHES

Instruments and Controls

61

Main MenustTable of Contents−

Pull the

Windshield Washers wiper control lever toward you and hold it. The washers spray until you release the lever. The wipers run at low speed, then complete one more sweep after you release the lever.

０３／０６／０５　１６：５７：３６　３１Ｓ５Ａ６３０　００６５　

Windshield Wipers and Washers

Push the right lever up or down to select a position.

MIST The wipers run at high speed until you release the lever.

−

OFF

−

The wipers are not activated.

−

The wipers operate every

INT few seconds. In low speed and high speed, the wipers run continuously. OnEXmodelintheU.S.,andLXand SimodelsinCanada Vary the delay by turning the INT TIME ring.

LO

−

The wipers run at low speed.

HI

−

The wipers run at high speed.

1. 2. 3. 4. 5. 6.

MIST OFF INT LO Low HI High Windshield Washers

Intermittent

− − −

62

Instruments and Controls

Main MenustTable of Contents０３／０６／０４　１４：２２：３１　３１Ｓ５Ａ６３０　００６６　

Turn Signal and Headlights

Turn Signal and Headlights

−

Turn Signal Push down on the left lever to signal a left turn and up to signal a right turn. To signal a lane change, push lightly on the lever and hold it. The lever will return to center when you release it or complete a turn.

−

Rotating switch

’’ position turns on the parking

Headlights On on the left lever controls to the ‘‘ lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights. Turning the switch to the ‘‘ on the headlights. If you leave the lights on with the key removed from the ignition switch, you will hear a reminder tone when you open the driver’s door.

’’ position turns

1. 2. 3. 4. 5. 6.

Turn Signal Off Parking and interior lights Headlight on High beams Flash high beams

−

High Beams To turn on, push the lever forward until you hear a click. The blue high beam indicator will light (see page ). Pull it back to return to low beams. To flash the high beams, pull the lever back lightly, then release it. The high beams will stay on as long as you hold the lever back.

56

Daytime Running Lights Canadian Models With the headlight switch off, the high beam headlights come on with reduced brightness when you turn the ignition switch ON (II) and release the parking brake. They remain on until you turn the ignition off, even if you set the parking brake.

The headlights revert to normal operation when you turn them on with the switch.

Instruments and Controls

63

Main MenustTable of Contents０３／０６／０４　１４：２２：３８　３１Ｓ５Ａ６３０　００６７　

Instrument Panel Brightness

SELECT/RESET KNOB

Adjust the brightness to the desired level with the headlight switch off, and also with the headlight switch on.

To reduce glare at night, the instrument panel illumination dims when you turn the light switch to

or

. Turning the Select/

Reset knob fully to the right will return the instrument panel to the brightness adjusted with the headlight switch off and a tone will sound.

DX models

KNOB

The knob on the instrument panel controls the brightness of the instru- ment panel lights. Turn the knob to adjust the brightness.

LX, U.S. EX, and Canadian Si models

OnLX,USEX,andCanadianSimodels There are six brightness levels. When you turn the knob, the odometer/trip meter display changes to circles that show you the current level. You will hear a tone when you reach the maximum or minimum brightness.

64

Instruments and Controls

Main MenustTable of Contents０３／０６／０４　１４：２２：４８　３１Ｓ５Ａ６３０　００６８　

Hazard Warning Button, Rear Window Defogger

Hazard Warning Button Rear Window Defogger

Make sure the rear window is clear and you have good visibility before starting to drive.

The defogger and antenna wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side to side.

Push the button between the center vents to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.

The rear window defogger will clear fog, frost, and thin ice from the window. Push the defogger button to turn it on and off. The light in the button lights to show the defogger is on. If you do not turn it off, the defogger will shut itself off after about 15 minutes. It also shuts off when you turn off the ignition. You have to turn it on again when you restart the vehicle.

Instruments and Controls

65

Main MenustTable of Contents3.

Push the lever up to lock the steering wheel in that position.

4.

Make sure you have securely locked the steering wheel in place by trying to move it up and down.

０３／０６／０４　１４：２２：５９　３１Ｓ５Ａ６３０　００６９　

Steering Wheel Adjustment

16

Seepage forimportantsafety informationabouthowtoproperly positionthesteeringwheel.

Make any steering wheel adjustment before you start driving.

Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.

Adjust the steering wheel only when the vehicle is stopped.

66

Instruments and Controls

To adjust the steering wheel upward or downward:

1.

Push the lever under the steering column all the way down.

2.

Move the steering wheel so it points to your chest, not toward your face. Make sure you can see the instrument panel gauges and indicators.

Main MenustTable of Contents０３／０６／０４　１４：２３：０９　３１Ｓ５Ａ６３０　００７０　

KEY NUMBER TAG

MASTER KEYS (Black)

VALET KEY (Gray)

You should have received a key number tag with your set of keys. You will need this key number if you ever have to get a key replaced use only Honda-approved key blanks.

These keys contain electronic circuits that are activated by the Immobilizer System. They will not work to start the engine if the circuits are damaged.

Keys and Locks

The master key fits all the locks on your vehicle.

The valet key works only in the ignition and the door locks. You can keep the trunk, trunk release handle and rear seat trunk access locked when you leave your vehicle and the valet key at a parking facility.

Protect the keys from direct sunlight, high temperature, and high humidity.

Do not drop the keys or set heavy objects on them.

Keep the keys away from liquids. If they get wet, dry them immediately with a soft cloth.

The keys do not contain batteries. Do not try to take them apart.

Instruments and Controls

67

Main MenustTable of Contents０３／０６／０４　１４：２３：１９　３１Ｓ５Ａ６３０　００７１　

Immobilizer System

The Immobilizer System protects your vehicle from theft. If an improperly-coded key (or other device) is used, the engine’s fuel system is disabled.

When you turn the ignition switch to ON (II), the Immobilizer System indicator should come on for a few seconds, then go out. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to LOCK (0), remove the key, reinsert it, and turn the switch to ON (II) again.

The system may not recognize your key’s coding if another immobilizer key or other metal object (i.e. key fob) is near the ignition switch when you insert the key.

68

Instruments and Controls

If the system repeatedly does not recognize the coding of your key, contact your Honda dealer.

Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle undriveable.

If you have lost your key and cannot start your engine, contact a Honda dealer.

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

Main MenustTable of Contents０３／０６／０４　１４：２３：３０　３１Ｓ５Ａ６３０　００７２　

If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key.

−

You can

ACCESSORY (I) operate the audio system and the accessory power sockets in this position.

The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), and START (III).

−

You can insert or

LOCK (0) remove the key only in this position. To turn the key, you must push the key in slightly. If your vehicle has an automatic transmission, the shift lever must also be in park.

−

This is the normal key

ON (II) position when driving. Several of the lights on the instrument panel come on as a test when you turn the ignition switch from ACCESSORY to ON.

−

Use this position

START (III) only to start the engine. The switch returns to ON (II) when you let go of the key.

Ignition Switch

You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or ACCESSORY (I) position and open the driver’s door. Remove the key to turn off the beeper.

If your vehicle has an automatic transmission, the shift lever must be in Park before you can remove the key from the ignition switch.

Removing the key from the ignition switch while driving locks the steering. This can cause you to lose control.

Remove the key from the ignition switch only when parked.

Instruments and Controls

69

Main MenustTable of Contents０３／０６／０４　１４：２３：４１　３１Ｓ５Ａ６３０　００７３　

Door Locks

Door Locks

Power Door Locks

Childproof Door Locks

Unlock

Lock

Each door has a lock tab on the top. Push the tab down to lock the door and pull it up to unlock.

To lock any passenger’s door when getting out of the vehicle, push the lock tab down and close the door. To lock the driver’s door, pull and hold the outside door handle then push the lock tab down. Release the handle, then close the door.

70

Instruments and Controls

Unlock

Lock

MASTER DOOR LOCK SWITCH

Standardonsomemodels All doors lock when you push down the lock tab on the driver’s door, or lock the driver’s door from the outside with the key. Only the driver’s door unlocks when you use the key or lock tab. To unlock the passen- gers’ doors, use the master door lock switch or the lock tab on each door.

LEVER

The childproof door locks are designed to prevent children seated in the rear from accidentally opening the rear doors. Each rear door has a lock lever near the edge. With the lever in the LOCK position, the door cannot be opened from the inside regardless of the position of the lock tab. To open the door, pull the lock tab up and use the outside door handle.

Main MenustTable of Contents０３／０６／０４　１４：２３：５３　３１Ｓ５Ａ６３０　００７４　

Trunk

TRUNK RELEASE HANDLE

Pull

MASTER KEY

MASTER KEY

To open the trunk, pull the trunk release handle to the left of the driver’s seat. To protect items in the trunk when you need to give the key to someone else, lock the trunk release handle with the master key and give the other person the valet key.

To close the trunk, press down on the trunk lid.

You can also use the master key to open the trunk lock.

Keep the trunk lid closed at all times while driving to avoid damaging it and to prevent exhaust gas from getting into the interior. See Carbon Monoxide Hazard, page

46

Door Locks

Emergency Trunk Opener

As a safety feature, your vehicle has a release lever on the trunk latch so the trunk can be opened from inside. To open the trunk, push the release lever to the left.

Parents should decide if their children should be shown how to use this feature.

Instruments and Controls

71

Main MenustTable of Contents０３／０６／０４　１４：２４：０４　３１Ｓ５Ａ６３０　００７５　

−

Press this button once

UNLOCK to unlock the driver’s door. Push it twice to unlock the other doors. If you do not open any doors within 30
seconds, they will automatically relock.

−

Press this button for

PANIC about one second to attract attention; the horn will sound and the exterior lights will flash for about 30 seconds. To cancel panic mode, press any other button on the remote transmitter or turn the ignition switch to ON (II).

RemoteTransmitterCare

Avoid dropping or throwing the transmitter. Protect the transmitter from extreme temperatures. Do not immerse the transmitter in any liquid. If you lose a transmitter, the replacement needs to be reprogrammed by a Honda dealer.

Remote Transmitter

LED

UNLOCK BUTTON

LOCK BUTTON

PANIC BUTTON

−

Onmodelsequipped LOCK Press this button once to lock all doors. Some exterior lights will flash. When you push LOCK twice within 5 seconds, you will hear a beep to verify that the doors are locked. You cannot lock it if any door is not fully closed or key is in the ignition switch.

72

Instruments and Controls

Main MenustTable of Contents０３／０６／０４　１４：２４：１３　３１Ｓ５Ａ６３０　００７６　

To replace the battery, move the round cover on the back of the transmitter by turning it counterclockwise with a coin. Insert a new battery with the side facing mark on the cover up. Align the with the ◎ transmitter. Set the cover in place and turn it clockwise.

▽ mark on the

＋

Replacing the Transmitter Battery

ROUND COVER

CUSHION RING

BATTERY

If it takes several pushes on the button to lock or unlock the doors, replace the battery as soon as possible. Battery type: CR2025

Remote Transmitter

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

Instruments and Controls

73

Main MenustTable of Contents０３／０６／０４　１４：２４：２２　３１Ｓ５Ａ６３０　００７７　

Seats

Front Seat Adjustments Seepages forimportantsafety informationandwarningsabouthowto properlypositionseatsandseat-backs.

11 13

−

Make all adjustments before you start driving.

74

Instruments and Controls

To adjust the seat forward and backward, pull up on the bar under the seat cushion’s front edge. Then try to move the seat to make sure it is locked in position.

To change the seat-back angle of the front seat, pull up on the lever on the outside of the seat bottom.

Main MenustTable of Contents０３／０６／０４　１４：２４：３１　３１Ｓ５Ａ６３０　００７８　

Driver’s Seat Height Adjustment

Head Restraints Seepage forimportantsafety informationandawarningabouthowto properlypositiontheheadrestraints.

14

FRONT

U.S.:LX,EX Canada:DX-G,LX,Si To adjust the height of the driver’s seat, turn the dial on the outside of the seat bottom.

RELEASE BUTTON

Your vehicle is equipped with head restraints in the front seats and the outboard seating positions in the rear.

Seats

The head restraints help protect you and your passengers from whiplash and other injuries. They are most effective when you adjust them so the back of the occupant’s head rests against the center of the restraint.

The head restraints in the front and rear outboard seating positions adjust for height. You need both hands to adjust the restraint. To raise it, pull upward. To lower the restraint, push the release button sideways and push the restraint down.

Instruments and Controls

75

Main MenustTable of Contents０３／０６／０４　１４：２４：４２　３１Ｓ５Ａ６３０　００７９　

Seats

Armrest

Folding Rear Seat

GUIDE

StandardonLXandEXmodelsinthe U.S.,andDX-G,LXandSimodelsin Canada Itisoptionalonothermodels.

The lid of the console compartment can be used as an armrest.

Make sure the passenger’s hands or fingers are away from the armrest before pushing it down.

76

Instruments and Controls

MASTER KEY

The left and right halves can be folded separately from inside the vehicle or inside the trunk. To fold down the seat-back from inside the vehicle, insert the master key in the lock on the rear shelf. To fold down the driver’s side, turn the key clockwise, pull down the top of the seat-back, then release the key. To fold down the passenger’s side, turn the key counter clockwise and perform the same procedure.

CENTER SHOULDER BELT When storing cargo, you can move the rear center shoulder belt out of the way by removing the belt from the guide.

Main MenustTable of Contents０３／０６／０４　１４：２４：５０　３１Ｓ５Ａ６３０　００８０　

Seats

Make sure all rear shoulder belts are positioned in front of the rear seat- back whenever it is in the upright position.

Do not put any heavy items on the seat-back when it is folded.

Pull

Pull

RELEASE

To release the seat-back from inside the trunk, pull the release under the trunk panel. Push the seat-back down, then let go of the release.

To lock the seat-back upright, push it firmly against the trunk panel. Make sure it is latched in place by pulling on the top of the seat.

Make sure all items in the trunk, or items extending through the opening into the back seat, are secured. Loose items can fly forward and cause injury if you have to brake hard. See 119

Carrying Cargo

on page

Never drive with the seat-back folded down and the trunk lid open. See on page

Carbon Monoxide Hazard 46

Instruments and Controls

77

Main MenustTable of Contents０３／０６／０４　１４：２４：５７　３１Ｓ５Ａ６３０　００８１　

Power Windows

OnLXandEXmodelsintheU.S.,and LXandSimodelsinCanada Your vehicle’s windows are electri- cally-powered. Turn the ignition switch to ON (II) to raise or lower any window.

Each door has a switch that controls its window. To open the window, push the switch down and hold it. Release the switch when you want the window to stop. Close the window by pulling back on the switch and holding it.

78

Instruments and Controls

DRIVER’S WINDOW SWITCH

Closing a power window on someone’s hands or fingers can cause serious injury.

Make sure your passengers are away from the windows before closing them.

MAIN SWITCH

The driver’s door armrest has a master power window control panel. To open any of the passenger’s win- dows, push down on the appropriate switch and hold it until the window reaches the desired position. To close the window, pull back on the window switch. Release the switch when the window gets to the position you want.

Main MenustTable of Contents０３／０６／０４　１４：２５：０４　３１Ｓ５Ａ６３０　００８２　

Power Windows

The light in the AUTO switch comes on when you turn the ignition switch to ON (II).

The MAIN switch controls power to the passengers’ windows. When you push in the MAIN switch, the passengers’ windows cannot be raised or lowered. The MAIN switch does not affect the driver’s window. To cancel this feature, push on the switch again to get it to pop out. Keep the MAIN switch pushed in when you have children in the vehicle so they do not injure themselves by operating the windows unintentionally.

The master control panel also con- tains these extra features:

−

AUTO To open the driver’s window fully, push the window switch firmly down and release it. The window automatically goes all the way down. To stop the window from going all the way down, pull back on the window switch briefly.

To open the driver’s window only partially, push the window switch down lightly and hold it. The window will stop as soon as you release the switch.

The AUTO function only works to lower the driver’s window. To raise the window, you must pull back on