Index
Home
231
2012 Civic CoupeCIVIC 2D-31TS8600.book 232 ページ 2011年3月7日 月曜日 午後1時10分
232
2012 Civic CoupeCIVIC 2D-31TS8600.book 233 ページ 2011年3月7日 月曜日 午後1時10分
QRG
Maintenance
This chapter discusses basic maintenance.
Before Performing Maintenance
Inspection and Maintenance ............ 234
Safety When Performing Maintenance..... 235
Parts and Fluids Used in Maintenance
Service ........................................... 236
Maintenance Minder™ .................... 237
Maintenance Under the Hood
Maintenance Items Under the Hood..... 245
Opening the Hood ........................... 247
Recommended Engine Oil ................ 248
Oil Check......................................... 249
Adding Engine Oil............................ 251
Changing the Engine Oil and Oil Filter ..... 252
Engine Coolant ................................ 255
Transmission Fluid............................ 257
Brake/Clutch Fluid............................ 260
Refilling Window Washer Fluid......... 261
Replacing Light Bulbs ....................... 262
Checking and Maintaining Wiper
Blades .......................................... 272
Checking and Maintaining Tires
Checking Tires ................................. 274
Tire and Loading Information Label...... 275
Tire Labeling .................................... 275
DOT Tire Quality Grading (U.S. Vehicles).......277
Wear Indicators................................ 279
Tire Service Life................................ 279
Tire and Wheel Replacement ........... 280
Tire Rotation.................................... 281
Winter Tires ..................................... 282
Battery............................................... 283
Remote Transmitter Care *
Replacing the Battery....................... 284
Heating and Cooling * System
Maintenance ................................... 285
Cleaning
Interior Care .................................... 286
Exterior Care.................................... 288
Index
Home
* Not available on all models
233
2012 Civic CoupeCIVIC 2D-31TS8600.book 234 ページ 2011年3月7日 月曜日 午後1時10分
Before Performing Maintenance
Inspection and Maintenance For your safety, perform all listed inspections and maintenance to keep your vehicle in good condition. If you become aware of any abnormality (noise, smell, insufficient brake fluid, oil residue on the ground, etc.), have your vehicle inspected by a dealer. (Note, however, that service at a dealer is not mandatory to keep your warranties in effect.) Refer to the separate maintenance booklet for detailed maintenance and inspection information.
■ Types of Inspection and Maintenance ■ Daily inspections Perform inspections before long distance trips, when washing the vehicle, or when refueling.
■ Periodic inspections • Check the automatic transmission fluid level monthly.
2 Automatic Transmission Fluid P. 257
• Check the brake fluid level monthly.
2 Brake/Clutch Fluid P. 260
• Check the tire pressure monthly. Examine the tread for wear and foreign objects.
2 Checking and Maintaining Tires P. 274
• Check the operation of the exterior lights monthly.
2 Replacing Light Bulbs P. 262
• Check the condition of the wiper blades at least every six months.
2 Checking and Maintaining Wiper Blades P. 272
QRG
TOC
Index
Home
234
* Not available on all models
1Inspection and Maintenance
U.S. models Maintenance, replacement, or repair of emissions control devices and systems may be done by any automotive repair establishment or individuals using parts that are "certified" to EPA standards.
According to state and federal regulations, failure to perform maintenance on the maintenance main items marked with # will not void your emissions warranties. However, all maintenance services should be performed in accordance with the intervals indicated by the information display */multi- information display *.
2 Maintenance Service Items
P. 239
P. 243
If you want to perform complex maintenance tasks that require more skills and tools, you can purchase a subscription to the Service Express website at www.techinfo.honda.com.
2 Authorized Manuals P. 329
If you want to perform maintenance yourself, make sure that you have the necessary tools and skills first. After performing maintenance, update the records in the separate maintenance booklet.
2012 Civic CoupeCIVIC 2D-31TS8600.book 235 ページ 2011年3月7日 月曜日 午後1時10分
uuBefore Performing MaintenanceuSafety When Performing Maintenance
Safety When Performing Maintenance Some of the most important safety precautions are given here. However, we cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task.
■ Maintenance Safety • To reduce the possibility of fire or explosion, keep cigarettes, sparks, and flames
away from the battery and all fuel related parts.
• To clean parts, use a commercially available degreaser or parts cleaner, not
gasoline.
• Wear eye protection and protective clothing when working with the battery or
compressed air.
• Engine exhaust contains carbon monoxide, which is poisonous and can kill you.
u Only operate the engine if there is sufficient ventilation.
■ Vehicle Safety • The vehicle must be in a stationary condition.
u Make sure your vehicle is parked on level ground, the parking brake is set, and
the engine is off.
• Be aware that hot parts can burn you.
u Make sure to let the engine and exhaust system cool thoroughly before
touching vehicle parts.
• Be aware that moving parts can injure you.
u Do not start the engine unless instructed, and keep your hands and limbs away
from moving parts.
1Safety When Performing Maintenance
3WARNING
Improperly maintaining this vehicle or failing to correct a problem before driving can cause a crash in which you can be seriously hurt or killed.
Always follow the inspection and maintenance recommendations according to the schedules in this owner's manual.
3WARNING
Failure to properly follow maintenance instructions and precautions can cause you to be seriously hurt or killed.
Always follow the procedures and precautions in this owner's manual.
QRG
TOC
Index
Home
235
2012 Civic CoupeCIVIC 2D-31TS8600.book 236 ページ 2011年3月7日 月曜日 午後1時10分
uuBefore Performing MaintenanceuParts and Fluids Used in Maintenance Service
QRG
Parts and Fluids Used in Maintenance Service The use of Honda genuine parts and fluids is recommended when maintaining and servicing your vehicle. Honda genuine parts are manufactured according to the same high quality standards used in Honda vehicles.
TOC
Index
Home
236
2012 Civic CoupeCIVIC 2D-31TS8600.book 237 ページ 2011年3月7日 月曜日 午後1時10分
Maintenance Minder™
If the engine oil life is less than 15%, you will see the Maintenance Minder messages appear on the information display * or the multi-information display * every time you turn the ignition switch to ON (w. The messages notify you when to change the engine oil, or when to bring your vehicle to a dealer for indicated maintenance services.
Models with information display To Use Maintenance MinderTM ■ Displaying the Engine Oil Life
1. Turn the ignition switch to ON (w. 2. Press the
(SEL/RESET) knob repeatedly
until the engine oil life appears on the information display.
The Maintenance Minder indicator ( ) stays on in the instrument panel after the engine oil life becomes 0%. Have the indicated maintenance done by a dealer immediately.
* Not available on all models
Continued
QRG
TOC
Index
Home
237
1Displaying the Engine Oil Life
Based on the engine operating conditions, the remaining engine oil life is calculated and displayed as a percentage.
Displayed Engine Oil
Calculated Engine Oil
Life (%)
100
90
80
70
60
50
40
30
20
15
10
Life (%)
100 to 91
90 to 81
80 to 71
70 to 61
60 to 51
50 to 41
40 to 31
30 to 21
20 to 16
15 to 11
10 to 6
5 to 1
2012 Civic CoupeCIVIC 2D-31TS8600.book 238 ページ 2011年3月7日 月曜日 午後1時10分
uuMaintenance Minder™uTo Use Maintenance MinderTM
QRG
■ Maintenance Minder Messages on the Information Display To switch the display, press the
(SEL/RESET) knob.
Oil Life Display
Explanation
Information
Maintenance Minder Indicator
The engine oil life indicator starts to appear along with other due soon maintenance item codes when the remaining oil life becomes 15 percent.
The SERVICE message also starts to appear along with the engine oil life indicator and the maintenance item codes.
The remaining engine oil life has passed its service life, and a negative distance appears after driving over 10 miles (U.S. models) or 10 km (Canadian models). The negative distance on the display blinks.
The engine oil is approaching the end of its service life.
The engine oil has almost reached the end of its service life, and the maintenance items should be inspected and serviced as soon as possible.
The engine oil life has passed. The maintenance items must be inspected and serviced immediately.
Starts to come on when the remaining engine oil life becomes 15 percent. It goes off when the display is switched.
Stays on as a reminder even when the display is switched.
TOC
Index
Home
238
2012 Civic CoupeCIVIC 2D-31TS8600.book 239 ページ 2011年3月7日 月曜日 午後1時10分
■ Maintenance Service Items
Maintenance Minder Indicator
Maintenance Minder Message
Main Item
Sub Items
uuMaintenance Minder™uTo Use Maintenance MinderTM
QRG
1Maintenance Service Items
• Independent of the Maintenance Minder
information, replace the brake fluid every 3 years. • Inspect idle speed every 160,000 miles (256,000
km).
• Adjust the valves during services A, B, 1, 2, or 3 if
they are noisy.
CODE
Maintenance Main Items
CODE
Maintenance Sub Items
● Replace engine oil*1
● Replace engine oil*1 and oil filter
● Inspect front and rear brakes/service as necessary
● Check parking brake adjustment
● Inspect tie rod ends, steering gearbox, and boots
● Inspect suspension components
● Inspect driveshaft boots
● Inspect brake hoses and lines (Including ABS/VSA)
● Inspect all fluid levels and condition of fluids
● Inspect exhaust system#
● Inspect fuel lines and connections#
● Rotate tires
● Replace air cleaner element*2
● Replace dust and pollen filter *,*3
● Inspect drive belt
● Replace transmission fluid
● Replace spark plugs
● Inspect valve clearance
● Replace engine coolant
*2: *3:
If you drive in dusty conditions, replace the air cleaner element every 15,000 miles (24,000 km). If you drive primarily in urban areas that have high concentrations of soot in the air from industry and from diesel-powered vehicles, replace the dust and pollen filter every 15,000 miles (24,000 km).
*1:
# :
If a message SERVICE does not appear more than 12 months after the display is reset, change the engine oil every year. See information on maintenance and emissions warranty.
* Not available on all models
Continued
TOC
Index
Home
239
2012 Civic CoupeCIVIC 2D-31TS8600.book 240 ページ 2011年3月7日 月曜日 午後1時10分
uuMaintenance Minder™uTo Use Maintenance MinderTM
QRG
■ Resetting the Display Reset the engine oil life display if you have performed the maintenance service.
1. Turn the ignition switch to ON (w. 2. Display the engine oil life by repeatedly
pressing the
(SEL/RESET) knob.
3. Press and hold the
knob for ten seconds
or more. u The engine oil life indicator and the
maintenance item codes blink.
4. Press the
knob for five seconds or more.
u The displayed maintenance items
disappear, and the engine oil life display returns to 100%.
1Resetting the Display
NOTICE Failure to reset the engine oil life after a maintenance service results in the system showing incorrect maintenance intervals, which can lead to serious mechanical problems.
The dealer will reset the engine oil life display after completing the required maintenance service. If someone other than a dealer performs maintenance service, reset the engine oil life display yourself.
TOC
Index
Home
240
2012 Civic CoupeCIVIC 2D-31TS8600.book 241 ページ 2011年3月7日 月曜日 午後1時10分
uuMaintenance Minder™uTo Use Maintenance MinderTM
QRG
Models with multi-information display To Use Maintenance MinderTM ■ Displaying the Engine Oil Life and Maintenance Items Maintenance items, which should be serviced at the same time that you replace the engine oil, appear on the multi-information display. You can view them on the Maintenance info screen at any time. 1. Turn the ignition switch to ON (w. 2. Press the MENU button to go to the Vehicle Menu screen. 3. Select Vehicle Information with the 4. Press the SOURCE button again to go to the Maintenance info screen. The
button, then press the SOURCE button.
engine oil life appears on the multi-information display.
Engine Oil Life
2345
50
Engine oil
Air filters
Main Item
Sub Item
Button
SOURCE Button MENU Button
SOURCE
MENU
Continued
1Displaying the Engine Oil Life and Maintenance Items
Based on the engine operating conditions, the remaining engine oil life is calculated and displayed as a percentage.
Displayed Engine Oil
Calculated Engine Oil
Life (%)
100
90
80
70
60
50
40
30
20
15
10
Life (%)
100 to 91
90 to 81
80 to 71
70 to 61
60 to 51
50 to 41
40 to 31
30 to 21
20 to 16
15 to 11
10 to 6
5 to 1
There is a list of maintenance main and sub items you
can view on the multi-information display.
2 Maintenance Service Items P. 243
TOC
Index
Home
241
2012 Civic CoupeCIVIC 2D-31TS8600.book 242 ページ 2011年3月7日 月曜日 午後1時10分
uuMaintenance Minder™uTo Use Maintenance MinderTM
QRG
■ Maintenance Minder Messages on the Multi-Information
Display
Maintenance Message
Oil Life Display
Explanation
Information
SERVICE DUE SOON
15%
2345
Engine oil
Air filters
SERVICE DUE NOW
5%
2345
15
2345
TOC
2345
Engine oil
Air filters
The remaining engine oil life is 15 to 6 percent. Once you switch the display by pressing the (display/information) button, this message will go off.
The engine oil is approaching the end of its service life, and the maintenance items should be inspected and serviced soon.
The remaining engine oil life is 5 to 1 percent. Press the switch to another display.
button to
The engine oil has almost reached the end of its service life, and the maintenance items should be inspected and serviced as soon as possible.
SERVICE PAST DUE
Negative Distance
2345
-30
2345
The remaining engine oil life has passed its service life, and a negative distance appears after driving over 10 miles (U.S. models) or 10 km (Canadian models). Press the
button to switch to another display.
The engine oil life has passed. The maintenance items must be inspected and serviced immediately.
The system message indicator (
) comes on along with the Maintenance Minder message.
Index
Home
242
2012 Civic CoupeCIVIC 2D-31TS8600.book 243 ページ 2011年3月7日 月曜日 午後1時10分
■ Maintenance Service Items
System Message Indicator
Maintenance Minder Message
2345
Main Item
Sub Items
uuMaintenance Minder™uTo Use Maintenance MinderTM
QRG
1Maintenance Service Items
• Independent of the Maintenance Minder
information, replace the brake fluid every 3 years. • Inspect idle speed every 160,000 miles (256,000
km).
• Adjust the valves during services A, B, 1, 2, or 3 if
they are noisy.
CODE
Maintenance Main Items
CODE
Maintenance Sub Items
● Replace engine oil*1
● Replace engine oil*1 and oil filter
● Inspect front and rear brakes/service as necessary
● Check parking brake adjustment
● Inspect tie rod ends, steering gearbox, and boots
● Inspect suspension components
● Inspect driveshaft boots
● Inspect brake hoses and lines (Including ABS/VSA)
● Inspect all fluid levels and condition of fluids
● Inspect exhaust system#
● Inspect fuel lines and connections#
● Rotate tires
● Replace air cleaner element*2
● Replace dust and pollen filter*3
● Inspect drive belt
● Replace transmission fluid
● Replace spark plugs
● Inspect valve clearance
● Replace engine coolant
*2: *3:
If you drive in dusty conditions, replace the air cleaner element every 15,000 miles (24,000 km). If you drive primarily in urban areas that have high concentrations of soot in the air from industry and from diesel-powered vehicles, replace the dust and pollen filter every 15,000 miles (24,000 km).
*1:
# :
If a message SERVICE does not appear more than 12 months after the display is reset, change the engine oil every year. See information on maintenance and emissions warranty.
Continued
TOC
Index
Home
243
2012 Civic Coupe1Resetting the Display
NOTICE Failure to reset the engine oil life after a maintenance service results in the system showing incorrect maintenance intervals, which can lead to serious mechanical problems.
The dealer will reset the engine oil life display after completing the required maintenance service. If someone other than a dealer performs maintenance service, reset the engine oil life display yourself.
CIVIC 2D-31TS8600.book 244 ページ 2011年3月7日 月曜日 午後1時10分
uuMaintenance Minder™uTo Use Maintenance MinderTM
QRG
■ Resetting the Display Reset the engine oil life display if you have performed the maintenance service.
2345
Engine Oil Life
Engine oil
Air filters
Maintenance Item Codes
SOURCE
SOURCE Button
–
Button
1. Turn the ignition switch to ON (w. 2. Go to the Maintenance info screen.
2 Displaying the Engine Oil Life and Maintenance Items P. 241
3. Press the SOURCE button.
u The oil life reset mode is displayed on the multi-information display.
4. Select Yes with the
–
button, then press the SOURCE button.
u The displayed maintenance items disappear, and the engine oil life display
returns to 100%.
u Any maintenance items that are necessary for your vehicle at the next
maintenance service will appear.
To cancel the oil life reset mode, select No, then press the SOURCE button.
TOC
Index
Home
244
2012 Civic CoupeCIVIC 2D-31TS8600.book 245 ページ 2011年3月7日 月曜日 午後1時10分
Maintenance Under the Hood
Maintenance Items Under the Hood 1.8 ℓ engine models
Engine Oil Dipstick (Orange Handle)
Engine Oil Fill Cap
Washer Fluid (Blue Cap)
Brake Fluid (Black Cap)
Manual transmission models Clutch Fluid (Light Gray Cap)
Automatic transmission models Automatic Transmission Fluid Dipstick (Yellow Loop)
Battery
Radiator Cap
Engine Coolant Reservoir
QRG
TOC
Index
Home
Continued
245
2012 Civic CoupeCIVIC 2D-31TS8600.book 246 ページ 2011年3月7日 月曜日 午後1時10分
uuMaintenance Under the HooduMaintenance Items Under the Hood
QRG
2.4 ℓ engine models
Engine Oil Fill Cap
Engine Oil Dipstick (Orange Handle)
Washer Fluid (Blue Cap)
TOC
Index
Home
246
Brake Fluid (Black Cap)
Clutch Fluid (Light Gray Cap)
Battery
Radiator Cap
Engine Coolant Reservoir
2012 Civic CoupeCIVIC 2D-31TS8600.book 247 ページ 2011年3月7日 月曜日 午後1時10分
Opening the Hood
Hood Release Handle
Pull
uuMaintenance Under the HooduOpening the Hood
QRG
1. Park the vehicle on a level surface, and set
1Opening the Hood
the parking brake.
2. Pull the hood release handle under the
lower left corner of the dashboard. u The hood will pop up slightly.
NOTICE Do not open the hood when the wiper arms are raised. The hood will strike the wipers, and may damage either the hood or the wipers.
When closing the hood, check that the hood is securely latched.
3. Push up the hood latch lever in the center of the hood to release the lock mechanism, and open the hood.
If the hood latch lever moves stiffly, or if you can open the hood without lifting the lever, the latch mechanism should be cleaned and lubricated.
Lever Support Rod Grip
Clamp
4. Remove the support rod from the clamp using the grip. Mount the support rod in the hood.
When closing, remove the support rod, and stow it in the clamp, then gently lower the hood. Remove your hand at a height of approximately 12 inches (30 cm) and let the hood close.
TOC
Index
Home
247
2012 Civic Coupe1Recommended Engine Oil
Engine Oil Additives Your vehicle does not require oil additives. In fact, they may adversely affect the engine performance and durability.
CIVIC 2D-31TS8600.book 248 ページ 2011年3月7日 月曜日 午後1時10分
uuMaintenance Under the HooduRecommended Engine Oil
QRG
Recommended Engine Oil
• Genuine Honda Motor Oil • Premium-grade 0W-20 detergent oil with an API Certification Seal on the
container.
Oil is a major contributor to your engine's performance and longevity. If you drive the vehicle with insufficient or deteriorated oil, the engine may fail or be damaged.
This seal indicates the oil is energy conserving and that it meets the American Petroleum Institute’s latest requirements.
Use a Genuine Honda Motor Oil or another commercial engine oil of suitable viscosity for the ambient temperature as shown.
Ambient Temperature
■ Synthetic oil You may also use synthetic motor oil if it is labeled with the API Certification Seal and is the specified viscosity grade.
TOC
Index
Home
248
2012 Civic CoupeCIVIC 2D-31TS8600.book 249 ページ 2011年3月7日 月曜日 午後1時10分
Oil Check We recommend that you check the engine oil level every time you refuel. Park the vehicle on level ground. Wait approximately three minutes after turning the engine off before you check the oil. 1.8 ℓ engine models
1. Remove the dipstick (orange handle). 2. Wipe the dipstick with a clean cloth or
paper towel.
3. Insert the dipstick back all the way into its
hole.
2.4 ℓ engine models
uuMaintenance Under the HooduOil Check
QRG
1Oil Check
If the oil level is near or below the lower mark, slowly add oil being careful not to overfill.
TOC
Index
Home
249
Continued
2012 Civic CoupeCIVIC 2D-31TS8600.book 250 ページ 2011年3月7日 月曜日 午後1時10分
uuMaintenance Under the HooduOil Check
QRG
1.8 ℓ engine models
4. Remove the dipstick again, and check the level. It should be between the upper and lower marks. Add oil if necessary.
Upper Mark Lower Mark
2.4 ℓ engine models
Upper Mark Lower Mark
TOC
Index
Home
250
2012 Civic CoupeCIVIC 2D-31TS8600.book 251 ページ 2011年3月7日 月曜日 午後1時10分
Adding Engine Oil
1.8 ℓ engine models
Engine Oil Fill Cap
2.4 ℓ engine models
Engine Oil Fill Cap
uuMaintenance Under the HooduAdding Engine Oil
QRG
1. Unscrew and remove the engine oil fill cap. 2. Add oil slowly. 3. Reinstall the engine oil fill cap, and tighten
it securely.
4. Wait for three minutes and recheck the
engine oil dipstick.
1Adding Engine Oil
If any oil spills, wipe it up immediately. Spilled oil may damage the engine compartment components.
NOTICE Do not fill the engine oil above the upper mark. Overfilling the engine oil can result in leaks and engine damage.
TOC
Index
Home
251
2012 Civic Coupe1Changing the Engine Oil and Oil Filter
NOTICE You may damage the environment if you do not dispose of the oil in a suitable way. If you are changing the oil by yourself, appropriately dispose of the used oil. Put the oil in a sealed container and take it to a recycling center. Do not throw the oil away into a garbage can or onto the ground.
CIVIC 2D-31TS8600.book 252 ページ 2011年3月7日 月曜日 午後1時10分
uuMaintenance Under the HooduChanging the Engine Oil and Oil Filter
QRG
Changing the Engine Oil and Oil Filter You must change the engine oil and oil filter regularly in order to maintain the engine's lubrication. The engine may be damaged if they are not changed regularly.
Change the oil and filter in accordance with the maintenance message on the information display */multi-information display *. 1.8 ℓ engine models
1. Run the engine until it reaches normal
operating temperature, and then turn the engine off.
2. Open the hood and remove the engine oil
fill cap.
1.8 ℓ engine models 3. Remove the bolts on the undercarriage
and remove the under cover.
Bolt
Under Cover
TOC
Index
Home
252
* Not available on all models
2012 Civic CoupeCIVIC 2D-31TS8600.book 253 ページ 2011年3月7日 月曜日 午後1時10分
uuMaintenance Under the HooduChanging the Engine Oil and Oil Filter
QRG
1.8 ℓ engine models
Drain Bolt
All models 4. Remove the drain bolt and washer from the bottom of the engine, and drain the oil into a suitable container.
2.4 ℓ engine models
Washer
Drain Bolt
Washer
TOC
Index
Home
253
Continued
2012 Civic CoupeCIVIC 2D-31TS8600.book 254 ページ 2011年3月7日 月曜日 午後1時10分
uuMaintenance Under the HooduChanging the Engine Oil and Oil Filter
QRG
1.8 ℓ engine models
Oil Filter
2.4 ℓ engine models
1Changing the Engine Oil and Oil Filter
You will need a special wrench to replace the oil filter. You can buy this wrench from a dealer.
When installing the new oil filter, follow the instructions supplied with the oil filter.
Reinstall the engine oil fill cap. Start the engine. The low oil pressure indicator should go off within five seconds. If it does not, turn off the engine, and check your work.
5. Remove the oil filter and dispose of the
remaining oil.
6. Check that the filter gasket is not stuck to
the engine contact surface. u If it is stuck, you must detach it.
7. Wipe away dirt and dust adhering to the contact surface of the engine block, and install a new oil filter. u Apply a light coat of new engine oil to
the oil filter rubber seal.
8. Put a new washer on the drain bolt, then
reinstall the drain bolt. u Tightening torque: 1.8 ℓ engine models 29 lbf∙ft (39 N∙m, 4.0 kgf∙m) 2.4 ℓ engine models 30 lbf∙ft (40 N∙m, 4.0 kgf∙m)
TOC
Index
Home
254
Oil Filter
9. Pour the recommended engine oil into the engine. u Engine oil change capacity (including filter):
1.8 ℓ engine models 3.9 US qt (3.7 L) 2.4 ℓ engine models 4.4 US qt (4.2 L)
10.Reinstall the engine oil fill cap securely and
start the engine.
11.Run the engine for a few minutes, and
then check that there is no leak from the drain bolt or oil filter.
12.Stop the engine, wait for three minutes,
and then check the oil level on the dipstick. u If necessary, add more engine oil.
2012 Civic CoupeCIVIC 2D-31TS8600.book 255 ページ 2011年3月7日 月曜日 午後1時10分
Engine Coolant
uuMaintenance Under the HooduEngine Coolant
QRG
Specified coolant: Honda Long Life Antifreeze/Coolant Type 2
1Engine Coolant
This coolant is premixed with 50% antifreeze and 50% water. Do not add any straight antifreeze or water.
We recommend you check the engine coolant level every time you refuel. Check the reserve tank first. If it is completely empty, also check the coolant level in the radiator. Add the engine coolant accordingly.
■ Reserve Tank
MAX
1. Check the amount of coolant in the reserve
tank.
Reserve Tank
MIN
2. If the coolant level is below the MIN mark,
add the specified coolant until it reaches the MAX mark.
3. Inspect the cooling system for leaks.
NOTICE 2.4 ℓ engine models You will need a more concentrated coolant if you are driving in extremely cold temperature below −31 °F (−35 °C). Consult your Honda dealer for details about a suitable coolant mixture.
All models If Honda antifreeze/coolant is not available, you may use another major brand non-silicate coolant as a temporary replacement. Check that it is a high quality coolant recommended for aluminum engines. Continued use of any non-Honda coolant can result in corrosion, causing the cooling system to malfunction or fail. Have the cooling system flushed and refilled with Honda antifreeze/coolant as soon as possible.
Do not add rust inhibitors or other additives to your vehicle's coolant system. They may not be compatible with the coolant or with the engine components.
Continued
TOC
Index
Home
255
2012 Civic CoupeCIVIC 2D-31TS8600.book 256 ページ 2011年3月7日 月曜日 午後1時10分
uuMaintenance Under the HooduEngine Coolant
QRG
■ Radiator
1.8 ℓ engine models
Radiator Cap
2.4 ℓ engine models
Radiator Cap
1. Make sure the engine and radiator are
cool.
2. Turn the radiator cap counterclockwise and relieve any pressure in the coolant system. Do not push the cap down when turning.
3. Push down and turn the radiator cap
counterclockwise to remove it.
4. The coolant level should be up to the base
of the filler neck. Add coolant if it is low.
5. Put the radiator cap back on, and tighten it
fully.
6. Pour coolant into the reserve tank until it
reaches the MAX mark. Put the cap back on the reserve tank.
1Radiator
3WARNING
Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.
Always let the engine and radiator cool down before removing the radiator cap.
NOTICE Pour the fluid slowly and carefully so you do not spill any. Clean up any spills immediately; they can damage components in the engine compartment.
TOC
Index
Home
256
2012 Civic CoupeCIVIC 2D-31TS8600.book 257 ページ 2011年3月7日 月曜日 午後1時10分
Transmission Fluid ■ Automatic Transmission Fluid
Specified fluid: Honda ATF DW-1 (automatic transmission fluid)
Check the fluid level when the engine is at normal operating temperature.
HOT Range
Upper Mark Lower Mark
1. Park on level ground, and start the engine. 2. Wait until the radiator fan starts and then
turn off the engine. u Perform step 3 after waiting for about 60
seconds (less than 90 seconds).
3. Remove the dipstick (yellow loop) from the transmission and wipe it with a clean cloth. 4. Insert the dipstick all the way back into the
transmission securely, as shown in the image.
5. Remove the dipstick and check the fluid
level. u It should be between the upper and
lower marks in the HOT range.
6. If the level is below the lower mark, add
fluid into the dipstick hole to bring it to the level between the upper and lower marks, and have your vehicle checked by a dealer immediately.
Continued
uuMaintenance Under the HooduTransmission Fluid
QRG
1Automatic Transmission Fluid
NOTICE Do not mix Honda ATF DW-1 with other transmission fluids. Using a transmission fluid other than Honda ATF DW-1 may adversely affect the operation and durability of your vehicle's transmission, and damage the transmission. Any damage caused by using a transmission fluid that is not equivalent to Honda ATF DW-1 is not covered by Honda's new vehicle warranty.
NOTICE Pour the fluid slowly and carefully so you do not spill any. Clean up any spills immediately; they can damage components in the engine compartment.
TOC
Index
Home
257
2012 Civic CoupeCIVIC 2D-31TS8600.book 258 ページ 2011年3月7日 月曜日 午後1時10分
uuMaintenance Under the HooduTransmission Fluid
QRG
■ Manual Transmission Fluid
Specified fluid: Honda Manual Transmission Fluid (MTF)
Check the fluid level when the engine is at normal operating temperature. 1.8 ℓ engine models
1. Park the vehicle on level ground. 1.8 ℓ engine models 2. Remove the bolts with a wrench, then
carefully remove the under cover.
1Manual Transmission Fluid
If Honda MTF is not available, you may use the API certificated SAE 0 W-20 or 5 W-20 viscosity motor oil as a temporary measure. Replace with MTF as soon as possible. Motor oil does not contain the proper additives for the transmission and continued use can cause decreased shifting performance and lead to transmission damage.
3. Remove the holding clip and the bolt, then bend down the front edge of the left side under cover as shown in the image.
Bolt
Under Cover
1.8 ℓ engine models
Left Side Under Cover
Bolt
Clip
TOC
Index
Home
258
2012 Civic CoupeCIVIC 2D-31TS8600.book 259 ページ 2011年3月7日 月曜日 午後1時10分
uuMaintenance Under the HooduTransmission Fluid
QRG
1.8 ℓ engine models
2.4 ℓ engine models
All models 4. Remove the transmission filler bolt and
washer. Carefully feel inside the bolt hole with your fingers. u Check if the fluid level is up to the edge
of the bolt hole.
5. If the fluid level is not up to the edge of the bolt hole, add Honda Manual Transmission Fluid (MTF) until it runs out of the hole.
6. Put a new washer on the filler bolt, then
reinstall the filler bolt. u Tightening torque:
33 lbf∙ft (44 N∙m, 4.5 kgf∙m)
1.8 ℓ engine models 7. Reinstall the left side under cover with the
holding clip and the bolt.
8. Reinstall the under cover with the bolts.
TOC
Index
Home
259
2012 Civic CoupeCIVIC 2D-31TS8600.book 260 ページ 2011年3月7日 月曜日 午後1時10分
uuMaintenance Under the HooduBrake/Clutch Fluid
QRG
Brake/Clutch Fluid
Specified fluid: Honda Heavy Duty Brake Fluid DOT 3
1Brake/Clutch Fluid
Use the same fluid for both the brakes and clutch.
■ Checking the Brake Fluid
The fluid level should be between the MIN and MAX marks on the side of the reservoir.
MAX MIN
Brake Reservoir
■ Checking the Clutch Fluid
Clutch Reservoir
The fluid level should be between the MIN and MAX marks on the side of the reservoir.
MAX MIN
NOTICE Brake fluid marked DOT 5 is not compatible with your vehicle's braking system and can cause extensive damage.
If the specified brake fluid is not available, you should use only DOT 3 or DOT 4 fluid from a sealed container as a temporary replacement.
Using any non-Honda brake fluid can cause corrosion and decrease the longevity of the system. Have the brake system flushed and refilled with Honda Heavy Duty Brake Fluid DOT 3 as soon as possible.
If the brake fluid level is at or below the MIN mark, have a dealer inspect for leaks or worn brake pads as soon as possible.
1Checking the Clutch Fluid
If the clutch fluid level is at or below the MIN mark, have a dealer inspect for leaks or an excessively worn clutch plate as soon as possible.
TOC
Index
Home
260
2012 Civic CoupeCIVIC 2D-31TS8600.book 261 ページ 2011年3月7日 月曜日 午後1時10分
uuMaintenance Under the HooduRefilling Window Washer Fluid
Refilling Window Washer Fluid Check the amount of window washer fluid using the washer fluid level gauge on the cap.
If the level is low, fill the washer reservoir.
1Refilling Window Washer Fluid
NOTICE Do not use engine antifreeze or a vinegar/water solution in the windshield washer reservoir. Antifreeze can damage your vehicle's paint. A vinegar/water solution can damage the windshield washer pump.
Level Gauge
QRG
TOC
Index
Home
261
2012 Civic CoupeCIVIC 2D-31TS8600.book 262 ページ 2011年3月7日 月曜日 午後1時10分
QRG
Replacing Light Bulbs
Headlight Bulbs When replacing, use the following bulbs. High beam headlight: Low beam headlight:
60 W (HB3) 51 W (HB4)
■ High Beam Headlight
Coupler
Tab
Bulb
1. Remove the coupler.
u It can be removed by pushing the tab. 2. Rotate the old bulb to the left to remove. 3. Insert a new bulb into the headlight
assembly and turn it to the right.
4. Insert the coupler into the connector of the
bulb.
TOC
Index
Home
262
1Headlight Bulbs
NOTICE Halogen bulbs get very hot when lit. Oil, perspiration, or a scratch on the glass can cause the bulb to overheat and shatter.
The headlight aim is set by the factory, and does not need to be adjusted. However, if you regularly carry heavy items in the trunk, have the aiming readjusted at a dealer or by a qualified technician.
The HB3 and HB4 types are halogen bulbs. When replacing a bulb, handle it by its base, and protect the glass from contact with your skin or hard objects. If you touch the glass, clean it with denatured alcohol and a clean cloth.
The exterior lights' inside lenses (headlights, brake lamps, etc.) may fog temporarily after a vehicle wash or while driving in the rain. This does not impact the exterior light function. However, if you see a large amount of water or ice accumulated inside the lenses, have your vehicle inspected by a dealer.
2012 Civic CoupeCIVIC 2D-31TS8600.book 263 ページ 2011年3月7日 月曜日 午後1時10分
■ Low Beam Headlights
Clip (A)
Cover
Driver side 1.8 ℓ engine models 1. Remove the holding clips (A). Push up the tab, and remove the cover of the air intake duct and its upper part.
Tab
Air Intake Duct
uuReplacing Light BulbsuHeadlight Bulbs
QRG
1Low Beam Headlights
Holding clip (A-type) Pull the clip straight up to remove it.
2.4 ℓ engine models 1. Unlock the holding clips (B), then remove
the cover of the air intake duct.
Clip (B)
Keep the head of the clip raised when you insert it, push until it clicks.
Cover
Air Intake Duct
Fold in the upper part of the air intake duct to get enough working space.
Continued
TOC
Index
Home
263
2012 Civic CoupeCIVIC 2D-31TS8600.book 264 ページ 2011年3月7日 月曜日 午後1時10分
uuReplacing Light BulbsuHeadlight Bulbs
Passenger side All models 2. Remove the holding clip (C) using a flat-tip screwdriver, then remove the upper part of the windshield washer reservoir.
1Low Beam Headlights
Holding clip (B-type) Press down the central pin until it clicks to unlock it.
Central pin
Push the central pin back to lock the clip. Then, insert the clip into the hole and press on the central pin until it is flat.
Push until the pin is flat.
QRG
Clip (C)
TOC
Index
Home
264
2012 Civic CoupeCIVIC 2D-31TS8600.book 265 ページ 2011年3月7日 月曜日 午後1時10分
uuReplacing Light BulbsuHeadlight Bulbs
QRG
Coupler
All models 3. Remove the coupler.
u It can be removed by pushing the tab. 4. Rotate the old bulb to the left to remove. 5. Insert a new bulb into the headlight
assembly and turn it to the right.
6. Insert the coupler into the connector of the
bulb.
Tab
Bulb
1Low Beam Headlights
Holding clip (C-type) Insert a flat-tip screwdriver, lift and remove the central pin to remove the clip.
Central pin
Insert the clip with the central pin raised, and push until it is flat.
Push until the pin is flat.
TOC
Index
Home
265
2012 Civic Coupe1Fog Light Bulbs
NOTICE Halogen bulbs get very hot when lit. Oil, perspiration, or a scratch on the glass can cause the bulb to overheat and shatter.
The fog lights are halogen bulbs. When replacing a bulb, handle it by its plastic case, and protect the glass from contact with your skin or hard objects. If you touch the glass, clean it with denatured alcohol and a clean cloth.
CIVIC 2D-31TS8600.book 266 ページ 2011年3月7日 月曜日 午後1時10分
QRG
uuReplacing Light BulbsuFog Light Bulbs*
Fog Light Bulbs* When replacing, use the following bulbs. Fog Light: 55 W (H11)
1. Remove the screws using a Phillips-head
screwdriver and carefully pull the fog light assembly out of the bumper.
Screws
Coupler
2. Remove the coupler.
u It can be removed by pushing the tab. 3. Rotate the old bulb to the left to remove. 4. Insert a new bulb into the fog light
assembly and turn it to the right.
5. Insert the coupler into the connector of the
Bulb