the nearest automotive service facility. Tighten the wheel nuts to: 80 lbf·ft (108 N·m , 11 kgf·m)
16.
OnHXandEXmodelsintheU.S.,Si modelinCanada Remove the center cap before storing the flat tire in the trunk well.
Changing a Flat Tire
WING BOLT
SPACER CONE
17.
Place the flat tire face down in the spare tire well.
18.
Remove the spacer cone from the wing bolt, turn it over, and put it back on the bolt.
19.
Secure the flat tire by screwing the wing bolt back into its hole.
CONTINUED
Taking Care of the Unexpected 263
Main MenuTable of Contentsst02/07/09 17:44:07 31S5P620 0267
Changing a Flat Tire
20.
Store the jack in the trunk with the end bracket on the left side. Turn the jack’s end bracket to lock it in place. Store the tool kit.
Loose items can fly around the interior in a crash and could seriously injure the occupants.
Store the wheel, jack, and tools securely before driving.
21.
Store the wheel cover in the trunk. Make sure it does not get scratched or damaged.
22.
Lower the trunk floor, then close the trunk lid.
264
Taking Care of the Unexpected
Main MenuTable of Contentsst02/07/09 17:44:17 31S5P620 0268
If Your Engine Won’t Start
Diagnosing why your engine won’t start falls into two areas, depending on what you hear when you turn the key to START (III):
You hear nothing, or almost nothing. The engine’s starter motor does not operate at all, or operates very slowly.
You can hear the starter motor operating normally, or the starter motor sounds like it is spinning faster than normal, but the engine does not start up and run.
Nothing Happens or the Starter Motor Operates Very Slowly When you turn the ignition switch to START (III), you do not hear the normal noise of the engine trying to start. You may hear a clicking sound or series of clicks, or nothing at all. Check these things:
Check the transmission interlock. If you have a manual transmission, the clutch pedal must be pushed all the way to the floor or the starter will not operate. With an automatic transmission, it must be in Park or Neutral.
Turn the ignition switch to ON (II). Turn on the headlights and check their brightness. If the headlights are very dim or don’t light at all, the battery is discharged. See Jump Starting
on page
267
Turn the ignition switch to START (III). If the headlights do not dim, check the condition of the fuses. If the fuses are OK, there is proba- bly something wrong with the electrical circuit for the ignition switch or starter motor. You will need a qualified technician to determine the problem. (See Emergency Towing on page
283
.)
If the headlights dim noticeably or go out when you try to start the engine, either the battery is dis- charged or the connections are corroded. Check the condition of the battery and terminal connec- tions (see page then try jump starting the car from a booster battery (see page
). You can
224
267
).
Taking Care of the Unexpected 265
Main MenuTable of Contentsst02/07/09 17:44:27 31S5P620 0269
If Your Engine Won’t Start
The Starter Operates Normally In this case, the starter motor’s speed sounds normal, or even faster than normal, when you turn the ignition switch to START (III), but the engine does not run.
Do you have fuel? Turn the ignition switch to ON (II) for a minute and watch the fuel gauge. The low fuel level warning light may not be working, so you were not reminded to fill the tank.
Ifyoufindnothingwrong,youwill need a qualified technician to find the problem. See Towing on page
Emergency
283
There may be an electrical problem, such as no power to the fuel pump. Check all the fuses (see page
279
).
Your car has the Immobilizer
System. You should use a
properly-coded master or valet key
to start the engine (see page
).
81
A key that is not properly coded
will cause the immobilizer system
indicator in the dash panel to blink
rapidly.
Are you using the proper starting
Starting the
procedure? Refer to
Engine
171
on page
266
Taking Care of the Unexpected
Main MenuTable of Contentsst02/07/09 17:44:37 31S5P620 0270
To jump start your car, follow these directions closely:
1.
224
). In very cold
Open the hood and check the physical condition of the battery (see page weather, check the condition of the electrolyte. If it seems slushy or like ice, do not try jump starting until it thaws.
If your car’s battery has run down, you may be able to start the engine by using a booster battery. Although this seems like a simple procedure, you should take several precautions.
A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby.
Keep all sparks, open flames, and smoking materials away from the battery.
You cannot start a Honda with an automatic transmission by pushing or pulling it.
Jump Starting
If a battery sits in extreme cold, the electrolyte inside can f reeze. Attempting to jump start with a f rozen battery can cause it to rupture.
2.
Turn off all the electrical acces- sories: heater, A/C, stereo system, lights, etc. Put the transmission in Neutral or Park, and set the parking brake.
CONTINUED
Taking Care of the Unexpected 267
Main MenuTable of Contentsst02/07/09 17:44:44 31S5P620 0271
Jump Starting
3.
+
Connect one jumper cable to the ) terminal on your positive ( Honda’s battery. Connect the other end to the positive ( + terminal on the booster battery.
4.
−
Connect the second jumper cable to the negative ( ) terminal on the booster battery. Connect the other end to the grounding strap as shown. Do not connect this jumper cable to any other part of the engine.
BOOSTER BATTERY
The numbers in the illustrations show you the order to connect the jumper cables.
5.
If the booster battery is in another car, have an assistant start that car and run it at a fast idle.
268
Taking Care of the Unexpected
Main MenuTable of Contentsst02/07/09 17:44:55 31S5P620 0272
6.
7.
Start your car. If the starter motor still operates slowly, check the jumper cable connections to make sure they have good metal-to- metal contact.
Once your car is running, discon- nect the negative cable from your car, then from the booster battery. Disconnect the positive cable from your car, then the booster battery.
Keep the ends of the jumper cables away from each other and any metal on the car until all are disconnected. Otherwise, you may cause an electrical short.
Jump Starting, If Your Engine Overheats
If Your Engine Overheats The pointer of your car’s tempera- ture gauge should stay in the mid- range under most conditions. It may go higher if you are driving up a long steep hill on a very hot day. If it climbs to the red mark, you should determine the reason.
Your car can overheat for several reasons, such as lack of coolant or a mechanical problem. The only indication may be the temperature gauge climbing to or above the red mark. Or you may see steam or spray coming from under the hood. In either case, you should take immediate action.
Driving with the temperature gauge pointer at the red mark can cause serious damage to your engine.
Steam and spray from an overheated engine can seriously scald you.
Do not open the hood if steam is coming out.
CONTINUED
Taking Care of the Unexpected 269
Main MenuTable of Contentsst02/07/09 17:44:55 31S5P620 0272
6.
7.
Start your car. If the starter motor still operates slowly, check the jumper cable connections to make sure they have good metal-to- metal contact.
Once your car is running, discon- nect the negative cable from your car, then from the booster battery. Disconnect the positive cable from your car, then the booster battery.
Keep the ends of the jumper cables away from each other and any metal on the car until all are disconnected. Otherwise, you may cause an electrical short.
Jump Starting, If Your Engine Overheats
If Your Engine Overheats The pointer of your car’s tempera- ture gauge should stay in the mid- range under most conditions. It may go higher if you are driving up a long steep hill on a very hot day. If it climbs to the red mark, you should determine the reason.
Your car can overheat for several reasons, such as lack of coolant or a mechanical problem. The only indication may be the temperature gauge climbing to or above the red mark. Or you may see steam or spray coming from under the hood. In either case, you should take immediate action.
Driving with the temperature gauge pointer at the red mark can cause serious damage to your engine.
Steam and spray from an overheated engine can seriously scald you.
Do not open the hood if steam is coming out.
CONTINUED
Taking Care of the Unexpected 269
Main MenuTable of Contentsst02/07/09 17:45:04 31S5P620 0273
3.
If you do not see steam or spray, leave the engine running and watch the temperature gauge. If the high heat is due to overloading (climbing a long, steep hill on a hot day with the A/C running, for example), the engine should start to cool down almost immediately. If it does, wait until the tempera- ture gauge comes down to the mid- point then continue driving.
4.
If the temperature gauge stays at the red mark, turn off the engine.
5.
Wait until you see no more signs of steam or spray, then open the hood.
6.
7.
Look for any obvious coolant leaks,
such as a split radiator hose.
Everything is still extremely hot,
so use caution. If you find a leak, it
must be repaired before you
Emergency
continue driving (see
Towing
).
283
on page
If you don’t find an obvious leak,
check the coolant level in the
radiator reserve tank (see page
). If the level is below the
161
MIN mark, add coolant to halfway
between the MIN and MAX marks.
If Your Engine Overheats
1.
Safely pull to the side of the road. Put the transmission in Neutral or Park, and set the parking brake. Turn off the heating and cooling system and all other accessories. Turn on the hazard warning indicators.
2.
If you see steam and/or spray coming from under the hood, turn off the engine.
270
Taking Care of the Unexpected
Main MenuTable of Contentsst02/07/09 17:45:11 31S5P620 0274
If Your Engine Overheats
8.
If there was no coolant in the reserve tank, you may also have to add coolant to the radiator. Let the engine cool down until the pointer reaches the middle of the tempera- ture gauge, or lower, before check- ing the radiator.
Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.
Always let the engine and radiator cool down before removing the radiator cap.
9.
Using gloves or a large heavy cloth, turn the radiator cap counterclockwise, without pushing down, to the first stop. This releases any remaining pressure in the cooling system. After the pressure releases, push down on the cap and turn it until it comes off.
10.
Start the engine and set the temperature control dial to maximum. Add coolant to the radiator up to the base of the filler neck. If you do not have the proper coolant mixture available, you can add plain water. Remember to have the cooling system drained and refilled with the proper mixture as soon as you can.
11.
Put the radiator cap back on tightly. Run the engine and watch the temperature gauge. If it goes back to the red mark, the engine needs repair. (See Towing
Emergency
on page
283
.)
12.
If the temperature stays normal, check the coolant level in the radiator reserve tank. If it has gone down, add coolant to the MAX mark. Put the cap back on tightly.
Taking Care of the Unexpected 271
Main MenuTable of Contentsst02/07/09 17:45:21 31S5P620 0275
Low Oil Pressure Indicator
LOW OIL PRESSURE INDICATOR
LOW OIL PRESSURE INDICATOR
U.S.: HX, LX, EX Canada : LX, Si This indicator should light when the ignition switch is ON (II), and go out after the engine starts. It should never come on when the engine is running. If it starts flashing, it indicates that the oil pressure dropped very low for a moment, then recovered. If the indicator stays on with the engine running, it shows that the engine has lost oil pressure and serious engine damage is possible. In either case, you should take immediate action.
272
Taking Care of the Unexpected
DX models
Running the engine with low oil pressure can cause serious mechanical damage almost immediately. Turn of f the engine as soon as you can saf ely get the car stopped.
1.
Safely pull off the road and shut off the engine. Turn on the hazard warning indicators.
2.
3.
4.
160
). Although oil level
Let the car sit for a minute. Open the hood and check the oil level (see page and oil pressure are not directly connected, an engine that is very low on oil can lose pressure during cornering and other driving maneuvers.
If necessary, add oil to bring the level back to the full mark on the dipstick (see page
203
).
Start the engine and watch the oil
pressure indicator. If the light
does not go out within ten seconds,
turn off the engine. There is a
mechanical problem that needs to
be repaired before you can
continue driving. (See
Towing
.)
283
Emergency
on page
Main MenuTable of Contentsst02/07/09 17:45:29 31S5P620 0276
CHARGING SYSTEM INDICATOR
CHARGING SYSTEM INDICATOR
Charging System Indicator
By eliminating as much of the electrical load as possible, you can drive several miles (kilometers) before the battery is too discharged to keep the engine running. Drive to a service station or garage where you can get technical assistance.
U.S.: HX, LX, EX Canada : LX, Si This indicator should come on when the ignition switch is ON (II), and go out after the engine starts. If it comes on brightly when the engine is running, it indicates that the charging system has stopped charging the battery.
DX models Immediately turn off all electrical accessories: radio, heater, A/C, rear defogger, cruise control, etc. Try not to use other electrically-operated controls such as the power windows. Keep the engine running and take extra care not to stall it. Starting the engine will discharge the battery rapidly.
Taking Care of the Unexpected 273
Main MenuTable of Contentsst02/07/09 17:45:38 31S5P620 0277
Malfunction Indicator Lamp
MALFUNCTION INDICATOR LAMP
DX models If you have recently refueled your car, the cause of this indicator coming on could be a loose or missing fuel fill cap. Check the cap and tighten it until it clicks several times. Replace the fuel fill cap if it is missing. Tightening the cap will not make the indicator turn off immediately; it takes one driving trip.
MALFUNCTION INDICATOR LAMP U.S.: HX, LX, EX Canada : LX, Si This indicator should light when the ignition switch is ON (II), and go out after the engine starts. If it comes on at any other time, it indicates one of the engine’s emissions control systems may have a problem. Even though you may feel no difference in your car’s performance, it can reduce your fuel economy and cause your car to put out excessive emissions. Continued operation may cause serious damage.
274
Taking Care of the Unexpected
If the indicator remains on past one driving trip, or the fuel cap was not loose or missing, have the car checked by the dealer as soon as possible. Drive moderately until the dealer has inspected the problem. Avoid full-throttle acceleration and driving at high speed.
You should also have the dealer inspect your car if this indicator comes on repeatedly, even though it may turn off as you continue driving.
If you keep driving with the malf unction indicator lamp on, you can damage your car’s emissions controls and engine. Those repairs may not be covered by your car’s warranties.
Main MenuTable of Contentsst02/07/09 17:45:47 31S5P620 0278
Malfunction Indicator Lamp, Brake System Indicator
Readiness Codes Your car has certain ‘‘readiness codes’’ that are part of the on-board diagnostics for the emissions systems. In some states, part of the emissions testing is to make sure these codes are set. If they are not set, the test cannot be completed.
If your car’s battery has been disconnected or gone dead, these codes are erased. It takes several days of driving under various conditions to set the codes again.
If possible, do not take your car for a state emissions test until the readiness codes are set. To check if they are set, turn the ignition ON (II), but do not start the engine. The Malfunction Indicator Lamp will come on for 20 seconds. If it then goes off, the readiness codes are set. If it blinks 5 times, the readiness codes are not set. See State Emissions Testing on page
297
Brake System Indicator
BRAKE SYSTEM INDICATOR
*
U.S.: HX, LX, EX Canada : LX, Si U.S. indicator shown *
The Brake System Indicator normally comes on when you turn the ignition switch ON (II). It is a reminder to check the parking brake. It comes on and stays lit if you do not fully release the parking brake.
CONTINUED
Taking Care of the Unexpected
275
Main MenuTable of Contentsst02/07/09 17:45:47 31S5P620 0278
Malfunction Indicator Lamp, Brake System Indicator
Readiness Codes Your car has certain ‘‘readiness codes’’ that are part of the on-board diagnostics for the emissions systems. In some states, part of the emissions testing is to make sure these codes are set. If they are not set, the test cannot be completed.
If your car’s battery has been disconnected or gone dead, these codes are erased. It takes several days of driving under various conditions to set the codes again.
If possible, do not take your car for a state emissions test until the readiness codes are set. To check if they are set, turn the ignition ON (II), but do not start the engine. The Malfunction Indicator Lamp will come on for 20 seconds. If it then goes off, the readiness codes are set. If it blinks 5 times, the readiness codes are not set. See State Emissions Testing on page
297
Brake System Indicator
BRAKE SYSTEM INDICATOR
*
U.S.: HX, LX, EX Canada : LX, Si U.S. indicator shown *
The Brake System Indicator normally comes on when you turn the ignition switch ON (II). It is a reminder to check the parking brake. It comes on and stays lit if you do not fully release the parking brake.
CONTINUED
Taking Care of the Unexpected
275
Main MenuTable of Contentsst02/07/09 17:45:55 31S5P620 0279
Brake System Indicator
BRAKE SYSTEM INDICATOR
*
DX models U.S. indicator shown *
276
Taking Care of the Unexpected
If it comes on at any other time, it indicates a problem with the car’s brake system. In most cases, the problem is a low fluid level in the brake fluid reservoir. Press lightly on the brake pedal to see if it feels normal. If it does, check the brake fluid level the next time you stop at a service station (see page ). If the fluid level is low, take the car to your dealer and have the brake system inspected for leaks or worn brake pads.
217
However, if the brake pedal does not feel normal, you should take immediate action. Because of the brake system’s dual-circuit design, a problem in one part of the system will still give you braking at two wheels. You will feel the brake pedal go down much farther before the car begins to slow down, and you will have to press harder on the pedal. The distance needed to stop will be much longer.
Slow down by shifting to a lower
gear, and pull to the side of the road
when it is safe. Because of the
longer distance needed to stop, it is
hazardous to drive the car. You
should have it towed, and repaired as
Emergency
soon as possible. (See
Towing
.)
283
on page
If you must drive the car a short distance in this condition, drive slowly and cautiously.
Main MenuTable of Contentsst02/07/09 17:46:04 31S5P620 0280
OnEXmodelintheU.S.,andSimodel inCanada If the electric motor will not close the moonroof, do the following:
1.
2.
Check the fuse for the moonroof motor (see page ). If the fuse is blown, replace it with one of the same or lower rating.
279
Try closing the moonroof. If the new fuse blows immediately or the moonroof motor still does not operate, you can close the moonroof manually.
3.
Get the moonroof wrench out of the tool kit in the trunk.
ROUND PLUG
Closing the Moonroof
SOCKET
4.
Use a screwdriver or coin to remove the round plug in the center of the headliner.
5.
Insert the moonroof wrench into the socket behind this plug. Turn the wrench until the moonroof is fully closed.
6.
Remove the wrench. Reinstall the round plug.
Taking Care of the Unexpected 277
Main MenuTable of Contentsst02/07/09 17:46:11 31S5P620 0281
Fuses
All the electrical circuits in your car have fuses to protect them from a short circuit or overload. These fuses are located in two fuse boxes.
UNDER-HOOD
INTERIOR
TAB
The under-hood fuse box is located in the engine compartment on the passenger’s side. To open it, push the tabs as shown.
The interior fuse box is underneath the steering column. To open it, turn the knobs as shown.
278
Taking Care of the Unexpected
Main MenuTable of Contentsst02/07/09 17:46:22 31S5P620 0282
282
and
Checking and Replacing Fuses
If something electrical in your car
stops working, the first thing you
should check for is a blown fuse.
Determine from the chart on pages
, or the diagram on the
281
fuse box lid, which fuse or fuses
control that component. Check those
fuses first, but check all the fuses
before deciding that a blown fuse is
not the cause. Replace any blown
fuses and check the component’s
operation.
1.
Turn the ignition switch to LOCK (0). Make sure the headlights and all other accessories are off.
2.
Remove the cover from the fuse box.
FUSE
FUSE PULLER
Fuses
BLOWN
3.
Check each of the large fuses in the under-hood fuse box by looking through the top at the wire inside. Removing these fuses requires a Phillips-head screw- driver.
4.
Check the smaller fuses in the under-hood fuse box and all the fuses in the interior fuse box by pulling out each fuse with the fuse puller provided in the under-hood fuse box.
CONTINUED
Taking Care of the Unexpected 279
Main MenuTable of Contentsst02/07/09 17:46:32 31S5P620 0283
Fuses
BLOWN
5.
Look for a burned wire inside the fuse. If it is burned, replace it with oneofthesparefusesofthesame rating or lower.
If you cannot drive the car without fixing the problem, and you do not have a spare fuse, take a fuse of the same rating or a lower rating from one of the other circuits. Make sure you can do without that circuit temporarily (such as the accessory power socket or radio).
280
Taking Care of the Unexpected
If you replace the blown fuse with a spare fuse that has a lower rating, it might blow out again. This does not indicate anything wrong. Replace the fuse with one of the correct rating as soon as you can.
Replacing a f use with one that has a higher rating greatly increases the chances of damaging the electrical system. If you do not have a replace- ment f use with the proper rating f or the circuit, install one with a lower rating.
6.
If the replacement fuse of the same rating blows in a short time, there is probably a serious electrical problem in your car. Leave the blown fuse in that circuit and have your car checked by a qualified mechanic.
StandardforHX,LXandEXmodelsin
theU.S.,andLXandSimodelsin
Canada
If the radio fuse is removed, the
audio system will disable itself. The
nexttimeyouturnontheradioyou
will see ‘‘
’’ in the frequency
display. Use the Preset buttons to
enter the five-digit code (see page
149
).
Onallmodels When the audio system is disabled, the clock setting in the audio system will be canceled. You will need to reset the clock according to the instructions in the audio system section on this owner’s manual.
Main MenuTable of Contentsst02/07/09 17:46:39 31S5P620 0284
UNDER-HOOD FUSE BOX
No.
Amps.
Circuits Protected
Fuses
10
11
12
13
14
15
16
17
18
19
20
−
20 A 15 A 7.5 A 20 A 10 A 15 A 15 A 20 A 10 A 40 A 40 A 40 A 40 A 40 A 15 A 20 A 15 A − 80 A 40 A −
21 25 7.5 A 30 A
Condenser Fan
Small Lights
Interior Light
Cooling Fan
Hazard, Turn Signals
FI ECU
Horn, Brake Light
ABS F/S
Back Up
ABS Motor
Rear Defroster
Heater Motor
Power Window
Option
Left Headlight
Door Lock
Right Headlight
Not Used
Battery
Ignition 1
Spare Fuses
CONTINUED
Taking Care of the Unexpected 281
Main MenuTable of Contentsst02/07/09 17:46:48 31S5P620 0285
Fuses
INTERIOR FUSE BOX
No. Amps.
Circuits Protected
15 A 20 A 10 A 10 A −
Ignition Coil LAF Heater Daytime Running Lights Alternator Not Used
*
282
Taking Care of the Unexpected
No. Amps.
Circuits Protected
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
7.5 A 20 A 7.5 A 10 A 7.5 A 7.5 A 7.5 A 10 A 10 A − − 15 A 15 A 7.5 A 20 A − 20 A 20 A − −
*
Power Window Relay Moonroof Accessory, Radio SIDE SRS Meter ABS Daytime Running Lights SRS Power Mirrors (Security) Not Used Fuel Pump Accessory Power Socket Turn Signal Lights Front Wipers Not Used Front Right Power Window Front Left Power Window Not Used Not Used
*
: On Canadian models
Main MenuTable of Contentsst02/07/09 17:46:59 31S5P620 0286
If your car needs to be towed, call a professional towing service or, if you belong to one, an organization that provides roadside assistance. Never tow your car behind another vehicle with just a rope or chain. It is very dangerous.
There are three popular types of professional towing equipment.
−
The operator Flat-bedEquipment loads your car on the back of a truck. This is the best way to transport your Honda.
−
The tow
Wheel-liftEquipment truck uses two pivoting arms that go under the tires (front or rear) and lift them off the ground. The other two This is tires remain on the ground. an acceptable way to tow your Honda.
−
The tow
Sling-typeEquipment truck uses metal cables with hooks on the ends. These hooks go around parts of the frame or suspension and the cables lift that end of the car off the ground. Your car’s suspension and body can be seriously damaged. This method of towing is unacceptable.
If your Honda cannot be transported by flat-bed, it should be towed by wheel-lift equipment with the front wheels off the ground. If due to damage, your car must be towed with the front wheels on the ground, do the following:
Emergency Towing
5-speedManualTransmissionand ContinuouslyVariableTransmission (CVT)
Release the parking brake. Shift the transmission to Neutral.
AutomaticTransmission
Release the parking brake. Start the engine. Shift to D, then to N. Turn off the engine.
Improper towing preparation will damage the transmission. Follow the above procedure exactly. If you cannot shif t the transmission or start the engine (automatic transmission), your car must be transported with the f ront wheels of f the ground.
CONTINUED
Taking Care of the Unexpected 283
Main MenuTable of Contentsst02/07/09 17:47:05 31S5P620 0287
Trying to lif t or tow your car by the bumpers will cause serious damage. The bumpers are not designed to support the car’s weight.
If you decide to tow your car with all four wheels on the ground, make sure you use a properly-designed and attached tow bar. Prepare the car for towing as described above, and leave the ignition switch in Accessory (I) so the steering wheel does not lock. Make sure the radio and any items plugged into the accessory power socket are turned off so they do not run down the battery.
The steering system can be damaged if the steering wheel is locked. Leave the ignition switch in Accessory (I), and make sure the steering wheel turns f reely bef ore you begin towing.
Emergency Towing
With the front wheels on the ground, it is best to tow the car no farther than 50 miles (80 km), and keep the speed below 35 mph (55 km/h).
If your car is equipped with a front spoiler, remove it before towing so it is not damaged.
284
Taking Care of the Unexpected
Main MenuTable of Contentsst02/07/09 17:47:10 31S5P620 0288
Technical Information
Thediagramsinthissectiongive you the dimensions and capacities of your Honda, and the locations of the identification numbers. It also includes information you should know about your vehicle’s tires and emissions control systems.
Identification Numbers Specifications DOT Tire Quality Grading
................ ................................
. 286
. 288
(U.S.Cars)
Treadwear Traction Temperature
............................. ................................. ...................................... ............................. ......................... ......
.290
. 290
. 290
. 291
. 292
. 293
Oxygenated Fuels Driving in Foreign Countries
Emissions Controls ....................... The Clean Air Act ..................... Crankcase Emissions Control .................................... Evaporative Emissions Control ....................................
System
System
Onboard Refueling Vapor
. 294
. 294
. 294
. 294
Recovery
. 295
Exhaust Emissions Controls . 295
. 295
................................ ... ....................
PGM-FI System Ignition Timing Control
System
................................
. 295
Three Way Catalytic
Converter
Replacement Parts
. 295
...........................
....................
. 295
Three Way Catalytic Converter . 296
..
. 297
..............
State Emissions Testing
....
. 297
Testing of Readiness Codes
Technical Information 285
Main Menust02/07/09 17:47:15 31S5P620 0289
Identification Numbers
Your car has several identifying numbers located in various places.
The Vehicle Identification Number (VIN) is the 17-digit number your Honda dealer uses to register your car for warranty purposes. It is also necessary for licensing and insuring your car. The easiest place to find the VIN is on a plate fastened to the top of the dashboard. You can see it by looking through the windshield on the driver’s side. It is also on the Certification label attached to the driver’s doorjamb, and is stamped on the engine compartment bulkhead. The VIN is also provided in bar code on the Certification label.
286
Technical Information
VEHICLE IDENTIFICATION NUMBER
CERTIFICATION LABEL
Main MenuTable of Contentsst02/07/09 17:47:21 31S5P620 0290
The Engine Number is stamped into the engine block.
AUTOMATIC TRANSMISSION NUMBER
The Transmission Number is on a label on top of the transmission.
MANUAL TRANSMISSION NUMBER
Identification Numbers
ENGINE NUMBER
Technical Information 287
Main MenuTable of Contentsst02/07/10 14:56:16 31S5P620 0291
Specifications
Dimensions Length Width Height Wheelbase Track
Front Rear
174.7 in (4,438 mm) 66.7 in (1,695 mm) 55.1 in (1,399 mm) 103.1 in (2,620 mm) 57.9 in (1,470 mm) 57.9 in (1,470 mm)
Weights Gross vehicle weight rating
See the certification label attached to the driver’s doorjamb.
Engine Type
Bore xStroke Displacement Compression ratio
Spark plugs
* *
1 : 2 :
DX, LX U.S.: HX, EX Canada: Si
Water cooled 4-stroke SOHC , SOHC VTEC *
*
4-cylinder gasoline engine
2.95 x 3.72 in (75.0 x 94.4 mm)
102 cu-in (1,668 cm )
9.5
9.9
*
*
See spark plug maintenance section page 221 .
*
288
Technical Information
* * *
4 : 5 : 6 :
Capacities Fuel tank
Engine coolant
Change * Manual Automatic CVT Total
Manual Automatic CVT
Engine oil
Change *
Including filter Without filter
Manual trans- mission fluid Automatic transmission fluid
Total Change Total Change
Total
Windshield washer reservoir 3 :
U.S. Cars Canada Cars
Approx. 13.2 US gal (50 )
1.03 US gal (3.9 ) 1.00 US gal (3.8 ) 1.00 US gal (3.8 )
1.32 US gal (5.0 ) 1.29 US gal (4.9 ) 1.29 US gal (4.9 )
3.4 US qt (3.2 ) * 3.7 US qt (3.5 ) * 3.2 US qt (3.0 ) * 3.5 US qt (3.3 ) * 4.4 US qt (4.2 ) 1.6 US qt (1.5 ) 1.7 US qt (1.6 ) 2.9 US qt (2.7 ) 3.4 US qt (3.2 ) * 6.3 US qt (6.0 ) 6.0 US qt (5.7 ) * 2.6 US qt (2.5 ) 4.8 US qt (4.5 )
Including the coolant in the reserve tank and that remaining in the engine. Reserve tank capacity: 0.108 US gal (0.41 ) Excluding the oil remaining in the engine. DX, LX EX, HX
HX
*
7 :
Main MenuTable of Contentsst02/07/10 14:59:00 31S5P620 0292
Air Conditioning Refrigerant type Charge quantity Lubricant oil type
Lights Headlights (HI/LO) Front turn signal/side marker lights Front parking light Rear turn signal lights Stop/Taillights/Rear side marker lights Back-up lights High-mount stop light License plate lights Ceiling light Front ceiling light * Spotlights
Trunk light
*
1 : U.S.: EX
Canada : Si
*
2 : LX
Battery Capacity
HFC-134a (R-134a) −
17.6 19.4 oz (500 550 g)
−
SP-10
12 V 12 V
− −
60/55 W (HB2) 21/5 W
12 V 12 V 12 V
− − −
3 CP 21 W 21/5 W
12 V 12 V 12 V 12 V 12 V 12 V 12 V 12 V
− − − − − − − −
18 W 21 W 3CP 10 W 5 W 5 W 8 W 5 W
*
*
Specifications
See page 282 or the fuse label attached to the inside of the fuse box door under the steering column. See page 281 or the fuse box cover.
−
0.00 in (0.0 mm) 0.08 in ( 2.0 mm)
− 0° 45’ − 2°14’
*
P185/70R14 87S P185/65R15 86H * T115/70D14 88M T125/70D15 95M
*
*
30 psi (210 kPa , 2.1 kgf/cm ) 60 psi (420 kPa , 4.2 kgf/cm )
Fuses Interior
Under-hood
Alignment Toe-in
Camber
Caster
Tires Size
Pressure
Front Rear Front Rear Front
Front/Rear
Spare
Front/Rear Spare
12 V 12 V
− −
36 AH/5 HR 38 AH/5 HR
*
3 :
*
4 :
*
5 :
*
6 :
U.S.: DX, HX and LX Canada: DX U.S.: EX Canada: LX, Si U.S.: DX, HX and LX Canada : DX, LX and Si U.S.: EX Canada: LX with ABS, Si with ABS
Technical Information 289
Main MenuTable of Contentsst02/07/09 17:48:14 31S5P620 0293
DOT Tire Quality Grading (U.S. Cars)
Treadwear The treadwear grade is a compara- tive rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one- half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual condi- tions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.
The tires on your car meet all U.S. Federal Safety Requirements. All tires are also graded for treadwear, traction, and temperature perform- ance according to Department of Transportation (DOT) standards. The following explains these gradings.
Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between the tread shoulder and the maximum section width. For example:
Treadwear 200
Traction AA
Temperature A
All passenger car tires must conform to Federal Safety Requirements in addition to these grades.
290
Technical Information
−
AA, A, B, C
Traction The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warning: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.
Main MenuTable of Contentsst02/07/09 17:48:20 31S5P620 0294
−
A, B, C
Temperature The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.
DOT Tire Quality Grading (U.S. Cars)
Warning: The temperature grade for this tire is established for a tire that is properly inflated and not over- loaded. Excessive speed, underinfla- tion, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
Technical Information
291
Main MenuTable of Contentsst02/07/09 17:48:29 31S5P620 0295
Oxygenated Fuels
Some conventional gasolines are being blended with alcohol or an ether compound. These gasolines are collectively referred to as oxygenated fuels. To meet clean air standards, some areas of the United States and Canada use oxygenated fuels to help reduce emissions.
If you use an oxygenated fuel, be sure it is unleaded and meets the minimum octane rating requirement.
Before using an oxygenated fuel, try to confirm the fuel’s contents. Some states/provinces require this information to be posted on the pump.
292
Technical Information
The following are the U.S. EPA and Canadian CGSB approved percentages of oxygenates:
ETHANOL (ethyl or grain alcohol) You may use gasoline containing up to 10 percent ethanol by volume. Gasoline containing ethanol may be marketed under the name ‘‘Gasohol.’’
(Methyl Tertiary Butyl
MTBE Ether) You may use gasoline containing up to 15 percent MTBE by volume.
(methyl or wood
METHANOL alcohol) Your vehicle was not designed to use fuel that contains methanol. Methanol can corrode metal parts in the fuel system, and also damage plastic and rubber components. This damage would not be covered by your warranties.
If you notice any undesirable operating symptoms, try another service station or switch to another brand of gasoline.
Fuel system damage or performance problems resulting from the use of an oxygenated fuel containing more than the percentages of oxygenates given above are not covered under warranty.
Main MenuTable of Contentsst02/07/09 17:48:34 31S5P620 0296
Driving in Foreign Countries
If you are planning to take your Honda outside the U.S. or Canada, contact the tourist bureaus in the areas you will be traveling in to find out about the availability of unleaded gasoline with the proper octane rating.
If unleaded gasoline is not available, be aware that using leaded gasoline in your Honda will affect perfor- mance and fuel mileage, and damage its emissions controls. It will no longer comply with U.S. and Canadian emissions regulations, and will be illegal to operate in North America. To bring your car back into compliance will require the replace- ment of several components, such as the oxygen sensors and the three way catalytic converter. These re- placements are not covered under warranty.
Technical Information 293
Main MenuTable of Contentsst02/07/09 17:48:43 31S5P620 0297
Emissions Controls
The burning of gasoline in your car’s engine produces several byproducts. Some of these are carbon monoxide (CO), oxides of nitrogen (NOx) and hydrocarbons (HC). Gasoline evaporating from the tank also produces hydrocarbons. Controlling the production of NOx, CO, and HC is important to the environment. Under certain conditions of sunlight and climate, NOx and HC react to form photochemical ‘‘smog.’’ Carbon monoxide does not contribute to smog creation, but it is a poisonous gas.
*
The Clean Air Act
The United States Clean Air Act
sets standards for automobile
emissions. It also requires that
automobile manufacturers explain to
owners how their emissions controls
workandwhattodotomaintain
them. This section summarizes how
the emissions controls work.
Scheduled maintenance is on page
194
*
In Canada, Honda vehicles comply
with the Canadian emission requirements, as specified in an agreement with Environment Canada, at the time they are manufactured.
Ventilation valve routes them from the crankcase back to the intake manifold. They are then drawn into the engine and burned.
Evaporative Emissions Control System As gasoline evaporates in the fuel tank, an evaporative emissions control canister filled with charcoal adsorbs the vapor. It is stored in this canister while the engine is off. After the engine is started and warmed up, the vapor is drawn into the engine and burned during driving.
Crankcase Emissions Control System Your car has a Positive Crankcase Ventilation System. This keeps gasses that build up in the engine’s crankcase from going into the atmosphere. The Positive Crankcase
294
Technical Information
Main MenuTable of Contentsst02/07/09 17:48:54 31S5P620 0298
Onboard Refueling Vapor Recovery The Onboard Refueling Vapor Recovery (ORVR) system captures the fuel vapors during refueling. The vapors are adsorbed in a canister filled with activated carbon. While driving, the fuel vapors are drawn into the engine and burned off.
Exhaust Emissions Controls The exhaust emissions controls include three systems: PGM-FI, Ignition Timing Control and Three Way Catalytic Converter. These three systems work together to control the engine’s combustion and minimize the amount of HC, CO, and NOx that comes out the tailpipe. The exhaust emissions control systems are separate from the crankcase and evaporative emissions control systems.
Emissions Controls
PGM-FISystem The PGM-FI System uses sequential multiport fuel injection. It has three subsystems: Air Intake, Engine Control, and Fuel Control. The Engine Control Module (ECM) or the Powertrain Control Module (PCM) uses various sensors to determine how much air is going into the engine. It then controls how much fuel to inject under all operat- ing conditions.
IgnitionTimingControlSystem This system constantly adjusts the ignition timing, reducing the amount of HC, CO and NOx produced.
Replacement Parts The emissions control systems are designed and certified to work to- gether in reducing emissions to levels that comply with the Clean Air Act. To make sure the emissions remain low, you should use only new genuine Honda replacement parts or their equivalent for repairs. Using lower quality parts may increase the emissions from your car.
The emissions control systems are covered by warranties separate from the rest of your car. Read your warranty manual for more informa- tion.
ThreeWayCatalyticConverter The three way catalytic converter is in the exhaust system. Through chemical reactions, it converts HC, CO, and NOx in the engine’s exhaust to carbon dioxide (CO ), dinitrogen (N ), and water vapor.
Technical Information 295
Main MenuTable of Contentsst02/07/09 17:49:04 31S5P620 0299
Three Way Catalytic Converter
The three way catalytic converter contains precious metals that serve as catalysts, promoting chemical reactions to convert the exhaust gasses without affecting the metals. The catalytic converter is referred to as a three-way catalyst, since it acts on HC, CO, and NOx. A replacement unit must be an original Honda part or its equivalent.
The three way catalytic converter must operate at a high temperature for the chemical reactions to take place. It can set on fire any com- bustible materials that come near it. Park your car away from high grass, dry leaves, or other flammables.
296
Technical Information
(U.S. EX and Canadian Si models)
(DX, LX and U.S. HX models)
THREE WAY CATALYTIC CONVERTER A defective three way catalytic converter contributes to air pollution, and can impair your engine’s per- formance. Follow these guidelines to protect your car’s three way catalytic converter.
THREE WAY CATALYTIC CONVERTER Keep the engine tuned-up.
Have your car diagnosed and repaired if it is misfiring, back- firing, stalling, or otherwise not running properly.
Always use unleaded gasoline. Even a small amount of leaded gasoline can contaminate the catalyst metals, making the three way catalytic converter ineffective.
Main MenuTable of Contentsst02/07/09 17:49:14 31S5P620 0300
Testing of Readiness Codes If you take your car for a state emissions test shortly after the battery has been disconnected or gone dead, it may not pass the test. This is because of certain ‘‘readiness codes’’ that must be set in the on- board diagnostics for the emissions systems. These codes are erased when the battery is disconnected, and set again only after several days of driving under a variety of conditions.
If the testing facility determines that the readiness codes are not set, you will be requested to return at a later date to complete the test. If you must get the vehicle re-tested within the next two or three days, you can condition the vehicle for re-testing by doing the following.
Make sure the gas tank is nearly, but not completely, full (around 3/4).
Make sure the vehicle has been
parked with the engine off for 8
hours or more.
Make sure the ambient temperature is between 20° and 95°F.
State Emissions Testing
Without touching the accelerator pedal, start the engine and let it idle for 20 seconds.
Keep the vehicle in Park
(automatic transmission) or
Neutral (manual transmission).
Increase the engine speed to 2,000
rpm and hold it there until the
temperature gauge rises to at least
1/4 of the scale (approximately 3
minutes).