2016 GMC Yukon Yukonxl Owners Manual

exceeded, a pop-up warning is displayed with a chime. Software Information : Press p while Software Information is highlighted to display open source software information.

Speedometer The speedometer shows the vehicle's speed in either kilometers per hour (km/h) or miles per hour (mph).

Fuel Gauge

Metric

English

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

134

Instruments and Controls

When the ignition is on, the fuel gauge indicates about how much fuel is left in the tank. There is an arrow near the fuel gauge pointing to the side of the vehicle the fuel door is on. When the indicator nears empty, the low fuel light comes on. There still is a little fuel left, but the vehicle should be refueled soon. Here are four things that some owners ask about. None of these show a problem with the fuel gauge: . At the service station, the fuel

pump shuts off before the gauge reads full. It takes a little more or less fuel to fill up than the gauge indicated. For example, the gauge may have indicated the tank was half full, but it actually took a little more or less than half the tank's capacity to fill the tank.

. The gauge moves a little while

turning a corner or speeding up.

. The gauge takes a few seconds

to stabilize after the ignition is turned on, and goes back to empty when the ignition is turned off.

Engine Oil Pressure Gauge

Metric

English

The engine oil pressure gauge shows the engine oil pressure in kPa (kilopascals) or psi (pounds per square inch) when the engine is running. Oil pressure can vary with engine speed, outside temperature and oil viscosity. A reading outside the normal operating range can be caused by a dangerously low oil level or some other problem causing low oil pressure. Check the vehicle's oil as soon as possible. See “OIL

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

PRESSURE LOW STOP ENGINE” under Engine Oil Messages 0 152
and Engine Oil 0 275.

Engine Coolant Temperature Gauge

Instruments and Controls

135

Caution

Lack of proper engine oil maintenance can damage the engine. Driving with the engine oil low can also damage the engine. The repairs would not be covered by the vehicle warranty. Check the oil level as soon as possible. Add oil if required, but if the oil level is within the operating range and the oil pressure is still low, have the vehicle serviced. Always follow the maintenance schedule for changing engine oil.

Metric

English

This gauge measures the temperature of the vehicle's engine coolant. While driving under normal operating conditions, if the needle moves into the red warning area, the engine is too hot. Pull off the road, stop the vehicle, and turn off the engine as soon as possible.

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

136

Instruments and Controls

Voltmeter Gauge

When the ignition is on, this gauge indicates the battery voltage. When the engine is running, this gauge shows the condition of the charging system. The gauge can transition from a higher to lower or a lower to higher reading. This is normal. If the vehicle is operating outside the normal operating range, the charging system light comes on. See Charging System Light 0 138
for more information. The voltmeter gauge may also read lower when in fuel economy mode. This is normal.

Readings outside the normal operating range can also occur when a large number of electrical accessories are operating in the vehicle and the engine is left idling for an extended period. This condition is normal since the charging system is not able to provide full power at engine idle. As engine speeds are increased, this condition should correct itself as higher engine speeds allow the charging system to create maximum power. The vehicle can only be driven for a short time with the readings outside the normal operating range. If the vehicle must be driven, turn off all accessories, such as the radio and air conditioner. Readings outside the normal operating range indicate a possible problem in the electrical system. Have the vehicle serviced as soon as possible.

Safety Belt Reminders

Driver Safety Belt Reminder Light There is a driver safety belt reminder light on the instrument cluster.

When the vehicle is started, this light flashes and a chime may come on to remind the driver to fasten their safety belt. Then the light stays on solid until the belt is buckled. This cycle may continue several times if the driver remains or becomes unbuckled while the vehicle is moving. If the driver safety belt is buckled, neither the light nor the chime comes on.

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

Instruments and Controls

137

The front passenger safety belt reminder light and chime may turn on if an object is put on the seat such as a briefcase, handbag, grocery bag, laptop, or other electronic device. To turn off the reminder light and/or chime, remove the object from the seat or buckle the safety belt.

Airbag Readiness Light This light shows if there is an electrical problem with the airbag system. The system check includes the airbag sensor(s), passenger sensing system (if equipped), the pretensioners, the airbag modules, the wiring, and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System 0 84.

The airbag readiness light comes on for several seconds when the vehicle is started. If the light does not come on then, have it fixed immediately.

{ Warning

If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash. To help avoid injury, have the vehicle serviced right away.

If there is a problem with the airbag system, a Driver Information Center (DIC) message may also come on. See Airbag System Messages 0 156.

Passenger Safety Belt Reminder Light There may be a passenger safety belt reminder light near the passenger airbag status indicator. See Passenger Sensing System 0 90.

For vehicles equipped with the passenger safety belt reminder light, when the vehicle is started this light flashes and a chime may come on to remind passengers to fasten their safety belt. Then the light stays on solid until the belt is buckled. This cycle continues several times if the passenger remains or becomes unbuckled while the vehicle is moving. If the passenger safety belt is buckled, neither the chime nor the light comes on.

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

138

Instruments and Controls

Passenger Airbag Status Indicator The vehicle has a passenger sensing system. See Passenger Sensing System 0 90 for important safety information. The passenger airbag status indicator is in the overhead console.

United States

Canada

When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check. Then, after

several more seconds, the status indicator will light either ON or OFF, or the on or off symbol, to let you know the status of the front outboard passenger frontal airbag. If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the front outboard passenger frontal airbag is allowed to inflate. If the word OFF or the off symbol is lit on the airbag status indicator, it means that the passenger sensing system has turned off the front outboard passenger frontal airbag. If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service.

{ Warning

If the airbag readiness light ever comes on and stays on, it means that something may be wrong

(Continued)

Warning (Continued)

with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light 0 137 for more information, including important safety information.

Charging System Light

The charging system light comes on briefly when the ignition is turned on, but the engine is not running, as a check to show the light is working. It should go out when the engine is started. If the light stays on, or comes on while driving, there may be a problem with the electrical charging

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

system. Have it checked by your dealer. Driving while this light is on could drain the battery. When this light comes on, or is flashing, the Driver Information Center (DIC) also displays a message. See Battery Voltage and Charging Messages 0 149. If a short distance must be driven with the light on, be sure to turn off all accessories, such as the radio and air conditioner.

Malfunction Indicator Lamp (Check Engine Light) This light is part of the vehicle’s emission control on-board diagnostic system. If this light is on while the engine is running, a malfunction has been detected and the vehicle may require service. The light should come on to show that it is working when the ignition is in ON/RUN with the engine not running for Key Access or in Service

Instruments and Controls

139

Only Mode for Keyless Access. See Ignition Positions (Keyless Access) 0 206 or Ignition Positions (Key Access) 0 208.

Malfunctions are often indicated by the system before any problem is noticeable. Being aware of the light and seeking service promptly when it comes on may prevent damage.

Caution

If the vehicle is driven continually with this light on, the emission control system may not work as well, the fuel economy may be lower, and the vehicle may not run smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty.

Caution

Modifications to the engine, transmission, exhaust, intake, or fuel system, or the use of replacement tires that do not meet the original tire specifications, can cause this light to come on. This could lead to costly repairs not covered by the vehicle warranty. This could also affect the vehicle’s ability to pass an Emissions Inspection/ Maintenance test. See Accessories and Modifications 0 272.

If the light is flashing : A malfunction has been detected that could damage the emission control system and increase vehicle emissions. Diagnosis and service may be required. To help prevent damage, reduce vehicle speed and avoid hard accelerations and uphill grades.

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

140

Instruments and Controls

If towing a trailer, reduce the amount of cargo being hauled as soon as possible. If the light continues to flash, find a safe place to park. Turn the vehicle off and wait at least 10 seconds before restarting the engine. If the light is still flashing, follow the previous guidelines and see your dealer for service as soon as possible. If the light is on steady : A malfunction has been detected. Diagnosis and service may be required. Check the following:

If fuel has been added to the vehicle using the capless funnel adapter, make sure that it has been removed. See “Filling the Tank with a Portable Gas Can” under Filling the Tank 0 253. The diagnostic system can detect if the adapter has been left installed in the vehicle, allowing fuel to evaporate into the atmosphere. A few driving trips with the adapter removed may turn off the light.

. Poor fuel quality can cause

inefficient engine operation and poor driveability, which may go away once the engine is warmed up. If this occurs, change the fuel brand. It may require at least one full tank of the proper fuel to turn the light off. See Fuel 0 251.

If the light remains on, see your dealer. Emissions Inspection and Maintenance Programs If the vehicle requires an Emissions Inspection/Maintenance test, the test equipment will likely connect to the vehicle's Data Link Connector (DLC).

The DLC is under the instrument panel to the left of the steering wheel. Connecting devices that are

not used to perform an Emissions Inspection/Maintenance test or to service the vehicle may affect vehicle operation See Add-On Electrical Equipment 0 269. See your dealer if assistance is needed. The vehicle may not pass inspection if: . The light is on when the engine

is running.

. The light does not come on

when the ignition is in ON/RUN with the engine not running for Key Access or in Service Only Mode for Keyless Access.

. Critical emission control systems

have not been completely diagnosed. If this happens, the vehicle would not be ready for inspection and might require several days of routine driving before the system is ready for inspection. This can happen if the 12-volt battery has recently been replaced or run down, or if the vehicle has been recently serviced.

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

Instruments and Controls

141

See your dealer if the vehicle will not pass or cannot be made ready for the test.

Brake System Warning Light The vehicle brake system consists of two hydraulic circuits. If one circuit is not working, the remaining circuit can still work to stop the vehicle. For normal braking performance, both circuits need to be working. If the warning light comes on, there is a brake problem. Have the brake system inspected right away.

Metric

English

This light should come on briefly when the engine is started. If it does not come on then, have it fixed so it will be ready to warn if there is a problem.

When the ignition is on, the brake system warning light also comes on when the parking brake is set. The light stays on if the parking brake does not fully release. If it stays on after the parking brake is fully released, it means the vehicle has a brake problem. If the light comes on while driving, pull off the road and stop carefully. The pedal might be harder to push, or the pedal can go closer to the floor. It may take longer to stop. If the light is still on, have the vehicle towed for service. See Towing the Vehicle 0 344. { Warning

The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service.

Antilock Brake System (ABS) Warning Light

This light comes on briefly when the engine is started. If the light does not come on, have it fixed so it will be ready to warn if there is a problem. If the light comes on while driving, stop as soon as it is safely possible and turn off the vehicle. Then start the engine again to reset the system. If the ABS light stays on, or comes on again while driving, the vehicle needs service. A chime may also sound when the light comes on steady. If the ABS light is the only light on, the vehicle has regular brakes, but the antilock brakes are not functioning.

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

142

Instruments and Controls

If both the ABS and the brake system warning light are on, the vehicle's antilock brakes are not functioning and there is a problem with the regular brakes. See your dealer for service. See Brake System Warning Light 0 141 and Brake System Messages 0 149.

Tow/Haul Mode Light

For vehicles with the Tow/Haul Mode feature, this light comes on when the Tow/Haul Mode has been activated. See Tow/Haul Mode 0 220.

Lane Keep Assist (LKA) Light

Vehicle Ahead Indicator

If available, this light comes on briefly while starting the vehicle. If it does not come on, have the vehicle serviced. This light is green if LKA is available to assist. LKA may assist by gently turning the steering wheel if the vehicle approaches a detected lane marking without using the turn signal in that direction. The LKA light will turn amber. This light is amber and flashes as a Lane Departure Warning (LDW) alert, to indicate that the lane marking has been crossed. See Lane Keep Assist (LKA) 0 249.

If equipped, this indicator will display green when a vehicle is detected ahead and amber when you are following a vehicle ahead much too closely. See Forward Collision Alert (FCA) System 0 243.

Traction Off Light

This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

dealer. If the system is working normally, the indicator light then turns off. The traction off light comes on when the Traction Control System (TCS) has been turned off by pressing and releasing the TCS/StabiliTrak button. This light and the StabiliTrak OFF light come on when StabiliTrak is turned off. If the TCS is off, wheel spin is not limited. Adjust driving accordingly. See Traction Control/Electronic Stability Control 0 228.

StabiliTrak® OFF Light

Instruments and Controls

143

This light comes on when the StabiliTrak system is turned off. If StabiliTrak is off, the Traction Control System (TCS) is also off. If the StabiliTrak and TCS are off, the system does not assist in controlling the vehicle. Turn on the TCS and the StabiliTrak systems and the warning light turns off. See Traction Control/Electronic Stability Control 0 228.

Traction Control System (TCS)/StabiliTrak® Light

If the light is on and not flashing, the TCS and potentially the StabiliTrak system have been disabled. A DIC message may display. Check the DIC messages to determine which feature(s) is no longer functioning and whether the vehicle requires service. If the light is on and flashing, the TCS and/or the StabiliTrak system is actively working. See Traction Control/Electronic Stability Control 0 228.

Tire Pressure Light

This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer.

This light comes on briefly when the engine is started. If the light does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off.

For vehicles with the Tire Pressure Monitor System (TPMS), this light comes on briefly when the engine is started. It provides information about tire pressures and the TPMS.

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

144

Instruments and Controls

When the Light Is On Steady This indicates that one or more of the tires are significantly underinflated. A Driver Information Center (DIC) tire pressure message may also display. See Tire Messages 0 157. Stop as soon as possible, and inflate the tires to the pressure value shown on the Tire and Loading Information label. See Tire Pressure 0 317.

When the Light Flashes First and Then Is On Steady If the light flashes for about a minute and then stays on, there may be a problem with the TPMS. If the problem is not corrected, the light will come on at every ignition cycle. See Tire Pressure Monitor Operation 0 320.

serviced by your dealer. If the system is working normally, the indicator light turns off. If the light stays on and the engine does not start, there could be a problem with the theft-deterrent system. See Immobilizer Operation (Key Access) 0 49 or Immobilizer Operation (Keyless Access) 0 50.

High-Beam On Light

This light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer 0 173.

Low Fuel Warning Light

This light is near the fuel gauge and comes on briefly when the ignition is turned on as a check to show it is working. It also comes on when the fuel tank is low on fuel. The light turns off when fuel is added. If it does not, have the vehicle serviced.

Security Light

The security light should come on briefly as the engine is started. If it does not come on, have the vehicle

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

IntelliBeam® Light

Lamps On Reminder

Adaptive Cruise Control Light

Instruments and Controls

145

This light comes on when the IntelliBeam system, if equipped, is enabled. See Exterior Lamp Controls 0 171.

Front Fog Lamp Light

This light comes on when the exterior lamps are in use. See Exterior Lamp Controls 0 171.

Cruise Control Light

This light is white when the Adaptive Cruise Control (ACC, if equipped) is on and ready, and turns green when the ACC is set and active. See Adaptive Cruise Control 0 233.

For vehicles with fog lamps, this light comes on when the fog lamps are on. The light goes out when the fog lamps are turned off. See Fog Lamps 0 176 for more information.

The cruise control light is white when the cruise control is on and ready, and turns green when the cruise control is set and active. See Cruise Control 0 231.

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

146

Instruments and Controls

Information Displays

Driver Information Center (DIC) The DIC displays are shown in the center of the instrument cluster in the Info app. See Instrument Cluster 0 131. The displays show the status of many vehicle systems. The controls for the DIC are on the right steering wheel control.

w or x : Press to move up or down in a list. In the main view, you can press up and down to move between different info app pages.

o or p : Press to move between the interactive display zones in the cluster. V (Set/Reset) : Press to open a menu or select a menu item. Press and hold to reset values on certain screens. DIC Info Page Options The info pages on the DIC can be turned on or off through the Settings menu. 1. Press o to access the cluster

applications.

2. Press w or x to scroll to the

Settings application.

3. Press V to enter the

Settings menu.

4. Scroll to Info Pages and

press p.

5. Press w or x to move

through the list of possible information displays.

6. Press V while an item is

highlighted to select or deselect that item. When an item is selected, a checkmark will appear next to it.

DIC Info Pages The following is the list of all possible DIC info page displays. Some may not be available for your particular vehicle. Some items may not be turned on by default but can be turned on through the Settings app. See “DIC Info Page Options” earlier in this section. Speed : Shows the vehicle speed in either kilometers per hour (km/h) or miles per hour (mph). Trip A or Trip B : Shows the current distance traveled, in either kilometers (km) or miles (mi), since the trip odometer was last reset. This also shows the approximate average liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number is calculated based on the number of L/100 km (mpg) recorded since the last time this menu item was reset.

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

Instruments and Controls

147

This number reflects only the approximate average fuel economy that the vehicle has right now, and will change as driving conditions change.

Press and hold V while this display is active to reset the trip odometer and the average fuel economy. Trip A and Trip B can also be reset by pressing p and choosing reset. Fuel Range : Shows the approximate distance the vehicle can be driven without refueling. LOW will be displayed when the vehicle is low on fuel. The fuel range estimate is based on an average of the vehicle's fuel economy over recent driving history and the amount of fuel remaining in the fuel tank. Oil Life : Shows an estimate of the oil's remaining useful life. If REMAINING OIL LIFE 99% is displayed, that means 99% of the current oil life remains. When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display.

See Engine Oil Messages 0 152. The oil should be changed as soon as possible. See Engine Oil 0 275. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule. See Maintenance Schedule 0 360. The Oil Life display must be reset after each oil change. It will not reset itself. Do not to reset the Oil Life display at any time other than when the oil has just been changed. It cannot be reset accurately until the next oil change. To reset the engine oil life system, press and hold V for several seconds while the Oil Life display is active. See Engine Oil Life System 0 277. Tire Pressure : Shows the approximate pressures of all four tires. Tire pressure is displayed in either kilopascal (kPa) or in pounds per square inch (psi). If the pressure is low, the value for that tire is shown in amber. See Tire Pressure Monitor System 0 319 and Tire Pressure Monitor Operation 0 320.

Fuel Economy : The center displays the approximate instantaneous fuel economy as a number and bar graph. Displayed above the bar graph is a running average of fuel economy for the most recently traveled selected distance. Displayed below the bar graph is the best average fuel economy that has been achieved for the selected distance. The selected distance is displayed at the top of the page as “last xxx mi/km.” Next to the odometer, the Active Fuel Management displays the number of cylinders the vehicle is running on. See Active Fuel Management® 0 215. Press p to select the distance or reset best value. Use w and x to choose the distance and press V. Press w and x to select “Reset Best Score.” Press V to reset the best average fuel economy. After reset, the momentary average fuel economy will display.

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

148

Instruments and Controls

The display provides information on how current driving behavior affects the running average and how well recent driving compares to the best that has been achieved for the selected distance. Timer : This display can be used as a timer. To start the timer, press V while this display is active. The display will show the amount of time that has passed since the timer was last reset. To stop the timer, press V briefly while this display is active and the timer is running. To reset the timer to zero, press and hold V while this display is active, or press p and select reset. Speed Limit (If Equipped) : Shows sign information, which comes from a roadway database in the onboard navigation. Engine Hours : Shows the total number of hours the engine has run. Transmission Fluid Temperature : Shows the temperature of the automatic

transmission fluid in either degrees Celsius (°C) or degrees Fahrenheit (°F). Trailer Brake (If Equipped) : On vehicles with the Integrated Trailer Brake Control (ITBC) system, the trailer brake display appears in the DIC. TRAILER GAIN shows the trailer gain setting. This setting can be adjusted from 0.0 to 10.0 with either a trailer connected or disconnected. OUTPUT shows the power output to the trailer anytime a trailer with electric brakes is connected. Output is displayed as a bar graph. Dashes may appear in the OUTPUT display if a trailer is not connected. Off Road : Displays vehicle pitch and roll information, road wheel angle, and four-wheel drive (4WD) status. Blank Page : Shows no information.

Vehicle Messages Messages displayed on the DIC indicate the status of the vehicle or some action that may be needed to correct a condition. Multiple messages may appear one after another. The messages that do not require immediate action can be acknowledged and cleared by pressing V or the trip odometer reset stem on the base cluster. The messages that require immediate action cannot be cleared until that action is performed. All messages should be taken seriously and clearing the message does not correct the problem. The following are the possible messages and some information about them.

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

Instruments and Controls

149

Battery Voltage and Charging Messages

BATTERY LOW START VEHICLE When the vehicle’s battery is severely discharged, this message will display and four chimes will sound. Start the vehicle immediately. If the vehicle is not started and the battery continues to discharge, the climate controls, heated seats, and audio systems will shut off and the vehicle may require a jump start. These systems will function again after the vehicle is started. BATTERY SAVER ACTIVE This message displays when the battery voltage drops below expected levels and features are disabled. Turn off all unnecessary accessory features.

SERVICE BATTERY CHARGING SYSTEM On some vehicles, this message displays if there is a problem with the battery charging system. Under certain conditions, the charging system light may also turn on in the instrument cluster. See Charging System Light 0 138. Driving with this problem could drain the battery. Turn off all unnecessary accessories. Have the electrical system checked as soon as possible. See your dealer. TRANSPORT MODE ON This message is displayed when the vehicle is in transport mode. Some features can be disabled while in this mode, including Remote Keyless Entry (RKE), remote start, and the vehicle alarm system. Take the vehicle to your dealer for service to turn transport mode off.

Brake System Messages

BRAKE FLUID LOW This message is displayed when the brake fluid level is low. See Brake Fluid 0 289. SERVICE BRAKE ASSIST This message may be displayed when there is a problem with the brake boost assist system. When this message is displayed, the brake boost assist motor might be heard operating and you might notice pulsation in the brake pedal. This is normal under these conditions. Take the vehicle to your dealer for service. SERVICE TRAILER BRAKE SYSTEM On vehicles with the Integrated Trailer Brake Control (ITBC) system, this message displays and a chime may sound when there is a problem with the ITBC system. When this message displays, power is no longer available to the trailer brakes.

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

150

Instruments and Controls

As soon as it is safe to do so, carefully pull your vehicle over to the side of the road and turn the ignition off. Check the wiring connection to the trailer and turn the ignition back on. If this message still displays, either your vehicle or the trailer needs service. See your dealer. See “Integrated Trailer Brake Control System” under Towing Equipment 0 262 for more information.

Compass Messages Dashes may be displayed if the vehicle temporarily loses communication with the Global Positioning System (GPS).

Cruise Control Messages

ADAPTIVE CRUISE SET TO XXX This message displays when the Adaptive Cruise Control (ACC) speed is set. See Adaptive Cruise Control 0 233.

ADAPTIVE CRUISE TEMPORARILY UNAVAILABLE This message displays when attempting to activate Adaptive Cruise Control (ACC) when it is temporarily unavailable. The ACC system does not need service. This can occur under the following conditions: . Cruise is turned on when the

vehicle is stopped.

. The radar cannot see objects well. See the next message. FRONT RADAR BLOCKED – SEE OWNERS MANUAL This message can display when: . The radar is not clean. Keep the radar sensors free of mud, dirt, snow, ice, and slush. Clean the entire front and/or rear of the vehicle. For cleaning instructions, see Exterior Care 0 350.

. Heavy rain or snow is interfering with the radar object detection or camera performance.

CRUISE SET TO XXX This message displays when the cruise control speed is set. See Cruise Control 0 231. NO CRUISE BRAKING GAS PEDAL APPLIED This message displays when Adaptive Cruise Control (ACC) is active and the driver is pressing the gas pedal. When this occurs, ACC will not brake. See Adaptive Cruise Control 0 233. SERVICE ADAPTIVE CRUISE CONTROL If this message displays, take the vehicle to your dealer to repair the system. Adaptive Cruise Control (ACC), Forward Collision Alert (FCA), and/or the Active Emergency Braking System may not work. Do not use these systems until the vehicle has been repaired.

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

Instruments and Controls

151

SHIFT TO PARK BEFORE EXITING This message may display if Adaptive Cruise Control (ACC) is engaged holding the vehicle at a stop, and the driver attempts to exit the vehicle. Put the vehicle in P (Park) before exiting.

Door Ajar Messages

DOOR OPEN This message displays and a chime may sound if a door is not fully closed. Stop and turn off the vehicle, check the door for obstructions, and close the door again. Check to see if the message still appears on the DIC. HOOD OPEN This message displays and a chime may sound if the hood is not fully closed. Stop and turn off the vehicle, check the hood for obstructions, and close the hood again. Check to see if the message still appears on the DIC.

REAR ACCESS OPEN This message will display when the liftgate is open. Close the liftgate completely.

Engine Cooling System Messages

A/C OFF DUE TO HIGH ENGINE TEMP This message displays when the engine coolant becomes hotter than the normal operating temperature. See Engine Coolant Temperature Gauge 0 135. To avoid added strain on a hot engine, the air conditioning compressor automatically turns off. When the coolant temperature returns to normal, the air conditioning compressor turns back on. You can continue to drive your vehicle. If this message continues to appear, have the system repaired by your dealer as soon as possible to avoid damage to the engine.

ENGINE OVERHEATED IDLE ENGINE This message displays when the engine coolant temperature is too hot. Stop and allow the vehicle to idle until it cools down. See Engine Coolant Temperature Gauge 0 135. When towing, use Tow/Haul Mode to prevent damage to the engine or transmission. See Tow/Haul Mode 0 220. ENGINE OVERHEATED STOP ENGINE This message displays and a chime may sound if the engine cooling system reaches unsafe temperatures for operation. Stop and turn off the vehicle as soon as it is safe to do so to avoid severe damage. This message clears when the engine has cooled to a safe operating temperature.

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

152

Instruments and Controls

Engine Oil Messages

CHANGE ENGINE OIL SOON This message displays when the engine oil needs to be changed. When you change the engine oil, be sure to reset the CHANGE ENGINE OIL SOON message. See Engine Oil Life System 0 277 for information on how to reset the message. See Engine Oil 0 275 and Maintenance Schedule 0 360. ENGINE OIL LOW ADD OIL On some vehicles, this message displays when the engine oil level may be too low. Check the oil level before filling to the recommended level. If the oil is not low and this message remains on, take the vehicle to your dealer for service. See Engine Oil 0 275. ENGINE OIL HOT IDLE ENGINE This message displays when the engine oil becomes hotter than the normal operating temperature. Stop

and allow the vehicle to idle until it cools down. See Engine Coolant Temperature Gauge 0 135. OIL PRESSURE LOW STOP ENGINE This message displays if low oil pressure levels occur. Stop the vehicle as soon as safely possible and do not operate it until the cause of the low oil pressure has been corrected. Check the oil as soon as possible and have the vehicle serviced by your dealer. See Engine Oil 0 275.

Engine Power Messages

ENGINE POWER IS REDUCED This message displays and a chime may sound when the cooling system temperature gets too hot and the engine further enters the engine coolant protection mode. See Engine Overheating 0 286 for more information. This message also displays when the vehicle's engine power is reduced. Reduced engine power can affect the vehicle's ability to

accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer for service as soon as possible.

Fuel System Messages

FUEL LEVEL LOW This message displays when the vehicle is low on fuel. Refuel as soon as possible.

Key and Lock Messages

NO REMOTE KEY WAS DETECTED PLACE KEY IN TRANSMITTER POCKET THEN START YOUR VEHICLE This message displays when trying to start the vehicle if an RKE transmitter is not detected. The transmitter battery may be weak.

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

Instruments and Controls

153

See “Starting the Vehicle with a Low Transmitter Battery” under Remote Keyless Entry (RKE) System Operation (Key Access) 0 31 or Remote Keyless Entry (RKE) System Operation 0 33. NO REMOTE DETECTED This message displays when the transmitter battery may be weak. See “Starting the Vehicle with a Low Transmitter Battery” under Remote Keyless Entry (RKE) System Operation (Key Access) 0 31 or Remote Keyless Entry (RKE) System Operation 0 33. NO REMOTE DETECTED PRESS BRAKE TO RESTART This message displays when attempting to turn off the vehicle and the RKE transmitter is no longer detected. Restarting is allowed without the RKE transmitter for five minutes. Press the brake pedal to restart the vehicle.

NUMBER OF KEYS PROGRAMMED This message displays when programming new keys to the vehicle. REMOTE LEFT IN VEHICLE This message displays when leaving the vehicle with the RKE transmitter still inside. REPLACE BATTERY IN REMOTE KEY This message displays when the battery in the RKE transmitter needs to be replaced.

Lamp Messages

TURN SIGNAL ON This message displays and a chime sounds if a turn signal is left on for 1.2 km (0.75 mi). Move the turn signal lever to the off position.

Object Detection System Messages

AUTOMATIC COLLISION PREP OFF This message displays when the Front Automatic Braking (FAB) System has been turned off. See Front Automatic Braking (FAB) System 0 246. AUTOMATIC COLLISION PREP REDUCED This message displays when the Front Automatic Braking (FAB) System has been set to the Alert setting. This setting disables most FAB functions. Some last-second automatic braking capability is still provided with the Alert setting, but braking is less likely to occur. See Front Automatic Braking (FAB) System 0 246. AUTOMATIC COLLISION PREP UNAVAILABLE This message displays when the Front Automatic Braking (FAB) System has been unavailable for

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

154

Instruments and Controls

some time. The FAB System does not need service. This message can display under the following conditions: . The front of the vehicle or

windshield is not clean. Keep these areas clean and free of mud, dirt, snow, ice, and slush. For cleaning instructions, see Exterior Care 0 350.

. Heavy rain or snow is interfering

with the object detection performance.

This message may also be displayed if there is a problem with the StabiliTrak system. See Traction Control/Electronic Stability Control 0 228. FORWARD COLLISION ALERT OFF This message displays when the Forward Collision Alert has been turned off.

FRONT CAMERA BLOCKED CLEAN WINDSHIELD This message displays when the camera is blocked. Cleaning the outside of the windshield behind the rearview mirror may correct the issue. The Lane Keep Assist (LKA) and the Lane Departure Warning (LDW) system will not operate. Forward Collision Alert (FCA) and Front Automatic Braking (FAB) may not work or may not work as well. LANE CHANGE ALERT OFF This message indicates that the driver has turned the Side Blind Zone Alert (SBZA) and Lane Change Alert (LCA) systems off. LANE KEEPING ASSIST UNAVAILABLE This message displays when the Lane Keep Assist (LKA) and Lane Departure Warning (LDW) system is temporarily unavailable. The LKA system does not need service.

This message could be due to the camera being blocked. Clean the outside of the windshield behind the rearview mirror. PARK ASSIST OFF This message displays when the Parking Assist system has been turned off or when there is a temporary condition causing the system to be disabled. SERVICE AUTOMATIC COLLISION PREP If this message displays, take the vehicle to your dealer to repair the system. Adaptive Cruise Control (ACC), Forward Collision Alert (FCA), and/or the Front Automatic Braking (FAB) System may not work. Do not use these systems until the vehicle has been repaired. SERVICE FRONT CAMERA If this message remains on after continued driving, the vehicle needs service. Do not use the Lane Keep Assist (LKA), Lane Departure Warning (LDW), Front Automatic

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

Instruments and Controls

155

Braking (FAB), and Forward Collision Alert (FCA) features. Take the vehicle to your dealer. SERVICE PARK ASSIST This message displays if there is a problem with the Parking Assist system. Do not use this system to help you park. See your dealer for service. SERVICE SIDE DETECTION SYSTEM If this message remains on after continued driving, the vehicle needs service. Side Blind Zone Alert (SBZA), Lane Change Alert (LCA), and Rear Cross Traffic Alert (RCTA) features will not work. Take the vehicle to your dealer. SIDE DETECTION SYSTEM UNAVAILABLE This message indicates that Side Blind Zone Alert (SBZA), Lane Change Alert (LCA), and Rear Cross Traffic Alert (RCTA) are disabled either because the sensor is blocked and cannot detect vehicles in the blind zone, or the

vehicle is passing through an open area, such as the desert, where there is insufficient data for operation. This message may also activate during heavy rain or due to road spray. The vehicle does not need service. For cleaning, see "Washing the Vehicle" under Exterior Care 0 350.

Ride Control System Messages

SERVICE LEVELING SYSTEM If the vehicle has the Magnetic Ride Control™ suspension system or Automatic Level Control, this message displays when the leveling system is not operating properly. Have the vehicle serviced by your dealer. SERVICE STABILITRAK If this message displays, it means there may be a problem with the StabiliTrak system. If you see this message, try to reset the system. Stop; turn off the engine for at least 15 seconds; then start the engine again. If this message still comes

on, it means there is a problem. You should see your dealer for service. The vehicle is safe to drive; however, you do not have the benefit of StabiliTrak, so reduce your speed and drive accordingly. SERVICE SUSPENSION SYSTEM If the vehicle has the Magnetic Ride Control suspension system, this message displays when the suspension system is not operating properly. Have the vehicle serviced by your dealer. SERVICE TRACTION CONTROL This message displays when there is a problem with the Traction Control System (TCS). When this message displays, the system will not limit wheel spin. Adjust your driving accordingly. See your dealer for service. See Traction Control/ Electronic Stability Control 0 228.

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

156

Instruments and Controls

STABILITRAK INITIALIZING This message may come on if the StabiliTrak system has not fully initialized because of road conditions or the incorrect tire size. When the StabiliTrak system is fully initialized, the message will turn off. See Traction Control/Electronic Stability Control 0 228. If this message continues to be displayed for multiple ignition cycles and on different road surfaces, see your dealer for service. TRACTION CONTROL OFF This message displays when the traction control has been turned off. See Traction Control/Electronic Stability Control 0 228. TRACTION CONTROL ON This message displays when the traction control is active. See Traction Control/Electronic Stability Control 0 228. STABILITRAK OFF This message displays when the StabiliTrak system has been turned off. Adjust your driving accordingly.

To limit wheel spin and realize the full benefits of the stability enhancement system, you should normally leave StabiliTrak on. See Traction Control/Electronic Stability Control 0 228. STABILITRAK OFF may also display when the stability control has been automatically disabled. Several conditions can cause this message to appear:

If the system is overheating, which could occur if StabiliTrak activates continuously for an extended period of time. If the brake system warning light is on. See Brake System Warning Light 0 141. If the stability system takes longer than usual to complete its diagnostic checks due to driving conditions. If an engine or vehicle-related problem has been detected and the vehicle needs service. See your dealer. If the transfer case is in Four-Wheel Drive Low.

The message turns off as soon as the conditions that caused the message to be displayed are no longer present.

Airbag System Messages

SERVICE AIRBAG This message displays if there is a problem with the airbag system. Take the vehicle to your dealer for service.

Security Messages

SERVICE THEFT DETERRENT SYSTEM This message displays when there is a problem with the theft-deterrent system. The vehicle may or may not restart, so you may want to take the vehicle to your dealer before turning off the engine. See Immobilizer Operation (Key Access) 0 49 or Immobilizer Operation (Keyless Access) 0 50.

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

Instruments and Controls

157

Steering System Messages

Starting the Vehicle Messages

STEERING ASSIST IS REDUCED DRIVE WITH CARE This message may display if a problem occurs with the electric power steering system. If this message appears, steering effort may be slightly higher than normal. The vehicle is still safe to drive. Use caution while in reduced assist mode. If this message is persistent or appears repeatedly, take the vehicle to your dealer for service. See Steering 0 191. SERVICE POWER STEERING This message displays when there is a problem with electric power steering. If this message displays and a reduction in steering performance or loss of power steering assistance is noticed, see your dealer. See Steering 0 191.

PRESS BRAKE TO START This message is displayed when attempting to start the vehicle without first pressing the brake pedal. SERVICE KEYLESS START SYSTEM This message is displayed if there is a problem with the pushbutton start system. Take the vehicle to your dealer for service.

Tire Messages

SERVICE TIRE MONITOR SYSTEM If equipped with the Tire Pressure Monitor System (TPMS), this message displays if a part on the system is not working properly. The tire pressure light also flashes and then remains on during the same ignition cycle. See Tire Pressure Light 0 143. Several conditions may cause this message to appear. See

Tire Pressure Monitor Operation 0 320. If the warning comes on and stays on, there may be a problem with the TPMS. See your dealer. TIRE LEARNING ACTIVE If equipped with the Tire Pressure Monitor System (TPMS), this message displays when the system is relearning the tire positions on your vehicle. The tire positions must be relearned after rotating the tires or after replacing a tire or sensor. See Tire Inspection 0 323, Tire Rotation 0 323, Tire Pressure Monitor System 0 319, and Tire Pressure 0 317. TIRE PRESSURE LOW ADD AIR TO TIRE If equipped with the Tire Pressure Monitor System (TPMS), this message displays when the pressure in one or more of the vehicle's tires is low. This message also displays with a vehicle picture to indicate the location of the low tire. The low tire pressure warning light will also come on. See Tire Pressure Light 0 143. You can

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

158

Instruments and Controls

receive more than one tire pressure message at a time. If a tire pressure message appears on the DIC, stop as soon as you can. Have the tire pressures checked and set to those shown on the Tire and Loading Information label. See Tires 0 310, Vehicle Load Limits 0 201, and Tire Pressure 0 317. The DIC also shows the tire pressure values. See Driver Information Center (DIC) 0 146.

Transmission Messages

4WD OFF If equipped with four-wheel drive, this message displays when the four-wheel-drive system is temporarily disabled due to an overheated condition. The vehicle will run in two-wheel drive when this message is present. Once the four-wheel-drive system cools down, the message turns off and the four-wheel-drive system returns to normal operation.

4WD SHIFT IN PROGRESS This message will display while the four-wheel-drive system is shifting. FOR 4WD LOW SHIFT TO NEUTRAL If a four-wheel drive shift into 4 n is requested, and the vehicle speed is correct, but the transmission is not in N (Neutral), this message will display until the transmission is shifted to N (Neutral). FOR 4WD LOW SLOW TO XXX If a four-wheel drive shift into 4 n is requested, but the vehicle speed is too high, this message will display until the correct vehicle speed is reached. GRADE BRAKING ACTIVE This message displays when grade braking has been activated while driving on downhill grades. This message will only appear the first time the feature is activated in an ignition cycle. See Tow/Haul Mode 0 220, Automatic Transmission 0 216, and Cruise Control 0 231.

GRADE BRAKING OFF This message displays when grade braking has been disabled with the Tow/Haul Mode button on the end of the shift lever. See Tow/Haul Mode 0 220, Automatic Transmission 0 216, and Cruise Control 0 231. GRADE BRAKING ON This message displays when grade braking has been enabled with the Tow/Haul Mode button on the end of the shift lever. See Tow/Haul Mode 0 220, Automatic Transmission 0 216, and Cruise Control 0 231. SERVICE 4WD If the vehicle has four-wheel drive, this message may display if a problem occurs with the four-wheel-drive system. If this message appears, stop as soon as possible and turn off the vehicle. Make sure the key is in the LOCK/ OFF position for at least one minute, then restart the vehicle and check for the message on the DIC display. If the message is still displayed or appears again when

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

you begin driving, the four-wheel-drive system needs service. See your dealer. SHIFT DENIED This message displays when the shift lever is in M (Manual Mode) and a transmission range has been selected that is unavailable at the current vehicle speed. TO EXIT 4WD LOW SHIFT TO NEUTRAL If a four-wheel drive shift out of 4 n is requested, and the vehicle speed is correct, but the transmission is not in N (Neutral), this message will display until the transmission is shifted to N (Neutral). TO EXIT 4WD LOW SLOW TO XXX If a four-wheel drive shift out of 4 n is requested, but the vehicle speed is too high, this message will display until the correct vehicle speed is reached.

Instruments and Controls

159

TRANSMISSION HOT IDLE ENGINE This message displays and a chime may sound if the transmission fluid in the vehicle gets hot. Driving with the transmission fluid temperature high can cause damage to the vehicle. Stop the vehicle and let it idle to allow the transmission to cool. This message clears and the chime stops when the fluid temperature reaches a safe level. When towing, use Tow/Haul Mode to prevent damage to the engine or transmission. See Tow/Haul Mode 0 220. VEHICLE IN 4WD LOW This message will display if the vehicle is driven in 4 n for about 10 minutes above 72 km/h (45 mph).

Vehicle Reminder Messages

CHECK TRAILER WIRING On vehicles with the Integrated Trailer Brake Control (ITBC) system, this message may display and a chime may sound when one of the following conditions exists: . A trailer with electric brakes

becomes disconnected from the vehicle. ‐ If the disconnect occurs while

the vehicle is stopped, this message clears itself after a short time.

‐ If the disconnect occurs while

the vehicle is moving, this message stays on until the ignition is turned off.

. There is a short in the wiring to

the electric trailer brakes.

When this message displays, power is no longer available to the trailer brakes.

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

160

Instruments and Controls

As soon as it is safe to do so, carefully pull the vehicle over to the side of the road and turn the ignition off. Check the wiring connection to the trailer and turn the ignition back on. This message clears if the trailer is reconnected. This message also clears if you acknowledge it. If this message still displays, either the vehicle or the trailer needs service. See your dealer. See “Integrated Trailer Brake Control System” under Towing Equipment 0 262. ICE POSSIBLE DRIVE WITH CARE This message displays when ice conditions are possible. TRAILER CONNECTED On vehicles with the Integrated Trailer Brake Control (ITBC) system, this message displays briefly when a trailer with electric or electric over hydraulic brakes is first connected to the vehicle.

This message clears itself after several seconds. This message also clears if you acknowledge it. After this message clears, the TRAILER GAIN and OUTPUT displays appear in the DIC. See Driver Information Center (DIC) 0 146 and “Integrated Trailer Brake Control System” under Towing Equipment 0 262.

Washer Fluid Messages

WASHER FLUID LOW ADD FLUID This message displays when the windshield washer fluid is low. Fill the windshield washer fluid reservoir as soon as possible. See Engine Compartment Overview 0 274 for the location of the windshield washer fluid reservoir. Also, see Washer Fluid 0 287 for more information.

Vehicle Personalization Use the audio system controls to access the personalization menus for customizing vehicle features. The following are all possible personalization features. Depending on the vehicle, some may not be available.

Radio Audio System Controls 1. Press the desired feature to

display a list of available options.

2. Press to select the desired

feature setting.

3. Press o BACK on the

faceplate or the 0 screen button to return to the previous menu or exit.

Turn the vehicle to ON/RUN to access the Settings menu, then select SETTINGS from the Home Page on the infotainment system display.

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

Instruments and Controls

161

Personalization Menus The following list of menu items may be available: . Time and Date . Language (Language) . Valet Mode . Radio . Vehicle . Bluetooth . Voice . Display . Rear Camera . Return to Factory Settings . Software Information Detailed information for each menu follows. Time and Date Manually set the time and date. See Clock 0 126. Language (Language) Select Language, then select from the available language(s).

The selected language will display on the system, and voice recognition (if equipped) will reflect the selected language. Valet Mode (If Equipped) This will lock the infotainment system and steering wheel controls. It may also limit access to vehicle storage locations (if equipped). To enable valet mode: 1. Enter a four-digit code on the

keypad.

2. Select Enter to go to the

confirmation screen.

3. Re-enter the four-digit code. Press LOCK or UNLOCK to lock or unlock the system. Press Back to go back to the previous menu. Radio Press to display the Radio menu and the following may display: . Manage Favorites . Number of Favorites Shown . Audible Touch Feedback . Bose AudioPilot

. Auto Volume . Maximum Startup Volume . Audio Cue Volume

Manage Favorites This allows favorites to be edited. See “Manage Favorites” in “Settings” under “Radio” in the infotainment manual.

Number of Favorites Shown Press to set the number of favorites to display. Select the desired number or select Auto and the infotainment system will automatically adjust the number of favorites shown.

Audible Touch Feedback This allows Audible Touch Feedback to be turned on or off. Select Off or On.

Bose AudioPilot This allows Bose AudioPilot to be turned on or off. Select Off or On.

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

162

Instruments and Controls

Auto Volume This feature adjusts the volume based on vehicle speed and ambient noise. Select Off, Low, Medium-Low, Medium, Medium-High, or High.

Maximum Startup Volume This feature sets the maximum startup volume. If the vehicle is started and the volume is greater than this level, the volume is adjusted to this level. To set the maximum startup volume, press + or − to increase or decrease.

Audio Cue Volume This feature sets the volume of audio files played at system startup and shutdown. Select On, then press + or − to increase or decrease the volume. Vehicle Select and the following may display: . Climate and Air Quality . Collision/Detection Systems

. Comfort and Convenience . Lighting . Power Door Locks . Remote Lock, Unlock, Start Climate and Air Quality Select the Climate and Air Quality menu and the following may display: . Auto Fan Max Speed . Auto Defog . Auto Rear Defog

Auto Fan Max Speed This feature will set the maximum auto fan speed. Select Low, Medium, or High.

Auto Defog When set to On, the front defog will automatically come on when the vehicle is started. Select Off or On.

Auto Rear Defog If equipped, this feature will automatically turn on the rear window defogger when it is cold outside. Select Off or On. Collision/Detection Systems Select the Collision/Detection Systems menu and the following may display: . Alert Type . Auto Collision Preparation . Go Notifier . Park Assist . Side Blind Zone Alert . Rear Cross Traffic Alert

Alert Type This feature will set crash alerts to beeps or seat vibrations. This setting affects all crash alerts including Forward Collision Alert, Lane Departure Warning, and Park Assist alerts. Select Beeps or Safety Alert Seat.

GMC Yukon/Yukon XL Owner Manual 9159297) - 2016 - crc - 5/13/15

(GMNA-Localizing-U.S/Canada-

Instruments and Controls

163

Auto Collision Preparation This feature will turn on or off the Forward Collision Alert (FCA) and Front Automatic Braking (FAB). The Off setting disables all FCA and FAB functions. With the Alert and Brake setting, both FCA and FAB are available. The Alert setting disables FAB, but some last-second automatic braking capability is still provided, though less likely to occur. See Front Automatic Braking (FAB) System 0 246. Select Off, Alert and Brake, or Alert.

Go Notifier This feature will give a reminder that Adaptive Cruise Control provides when it has brought the vehicle to a complete stop behind another stopping vehicle, and then that vehicle drives on. Select Off or On.

Park Assist This allows the feature to be turned on or off. See Assistance Systems for Parking or Backing 0 241.

Select Off, On, or On with Towbar Attached.

Side Blind Zone Alert This allows the feature to be turned on or off. See Side Blind Zone Alert (SBZA) 0 247. Select Off or On.

Rear Cross Traffic Alert This allows the feature to be turned on or off. See Assistance Systems for Parking or Backing 0 241. Select Off or On. Comfort and Convenience Select the Comfort and Convenience menu and the following may display: . Auto Memory Recall . Easy Exit Options . Chime Volume . Reverse Tilt Mirror . Auto Mirror Folding . Auto Wipe in Reverse Gear

Auto Memory Recall This allows the feature to be turned on or off. See Memory Seats 0 63. Select On or Off.

Easy Exit Options This allows the feature to be turned on or off. See Memory Seats 0 63. Select On or Off.