2005 GMC Savana Owners Manual

Download PDF Manual
2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. 2-3 At times you may notice a decrease in range. This is normal for any remote keyless entry system. If the transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work, try this: (cid:127) Check the distance. You may be too far from your vehicle. You may need to stand closer during rainy or snowy weather. (cid:127) Check the location. Other vehicles or objects may be blocking the signal. Take a few steps to the left or right, hold the transmitter higher, and try again. (cid:127) Check to determine if battery replacement or resynchronization is necessary. See “Battery Replacement” and “Resynchronization” under Remote Keyless Entry System Operation on page 2-4. If you are still having trouble, see your dealer or a qualiﬁed technician for service. Remote Keyless Entry System Operation Your vehicle may have this feature. Q(Lock): Press this button once to lock all of the doors. The parking lamps will ﬂash and the interior lamps will turn on brieﬂy. Press the lock button again within ﬁve seconds and the parking lamps will ﬂash and the horn will chirp brieﬂy. W(Unlock): Press this button once to unlock the driver’s door. The parking lamps will ﬂash twice and the interior lamps will turn on. Press the unlock button again within ﬁve seconds to unlock the remaining doors. The parking lamps will ﬂash. 2-4 (cid:127) Resynchronization Resynchronization may be necessary due to the security method used by this system. The transmitter does not send the same signal twice to the receiver. The receiver will not respond to a signal that has been sent previously. This prevents anyone from recording and playing back the signal from the transmitter. To resynchronize your transmitter, stand close to your vehicle and press and hold the lock and unlock buttons on the transmitter at the same time for seven seconds. The door locks should cycle to conﬁrm synchronization. If the locks do not cycle, see your dealer for service. L(Panic Alarm): The remote keyless entry transmitter comes equipped with an instant panic alarm. To use the alarm, press the horn symbol while the ignition is turned off. The horn will sound and both the interior and exterior lamps will ﬂash for up to thirty seconds. To stop the instant panic alarm, press the panic button again, wait for thirty seconds, or start the vehicle. j (Cargo Door): Press this button to unlock the cargo doors only. Matching Transmitter(s) to Your Vehicle Each remote keyless entry transmitter is coded to prevent another transmitter from unlocking your vehicle. If a transmitter is lost or stolen, a replacement can be purchased through your dealer. Remember to bring any remaining transmitters with you when you go to your dealer. When the dealer matches the replacement transmitter to your vehicle, any remaining transmitters must also be matched. Once your dealer has coded the new transmitter, the lost transmitter will not unlock your vehicle. Each vehicle can have a maximum of four transmitters matched to it. 2-5 Battery Replacement Under normal use, the battery in your remote keyless entry transmitter should last about four years. You can tell the battery is weak if the transmitter won’t work at the normal range in any location. If you have to get close to your vehicle before the transmitter works, it’s probably time to change the battery. Notice: When replacing the battery, use care not to touch any of the circuitry. Static from your body transferred to these surfaces may damage the transmitter. To replace the battery in the keyless entry transmitter, do the following: 2-6 1. Use an object like a coin to pry open the transmitter. 2. Once the transmitter is separated, use an object like a pencil to remove the old battery. Do not use a metal object. 3. Remove and replace the battery, positive (+) side down. 4. Snap the transmitter back together tightly to be sure no moisture can enter. 5. Press and hold the lock and unlock buttons on the remote keyless entry transmitter for seven seconds to resynchronize the transmitter. 6. Check the operation of the transmitter. Doors and Locks Door Locks {CAUTION: Unlocked doors can be dangerous. (cid:127) Passengers — especially children — can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked. So, wear safety belts properly and lock the doors whenever you drive. (cid:127) Young children who get into unlocked vehicles may be unable to get out. A child can be overcome by extreme heat and can suffer permanent injuries or even death from heat stroke. Always lock your vehicle whenever you leave it. (cid:127) Outsiders can easily enter through an unlocked door when you slow down or stop your vehicle. Locking your doors can help prevent this from happening. There are several ways to lock and unlock your vehicle. If your vehicle is equipped with keyless entry, see Remote Keyless Entry System on page 2-3 for more information. From the outside, use your key. To lock the door from the inside, slide the manual lever on your door down. To unlock the door, slide the manual lever up. 2-7 Power Door Locks Press the bottom side of the power door lock switch to lock all the doors at once. Press the top side of the power door lock switch to unlock all the doors at once. Rear Door Security Locks Security locks are located on the passenger side rear door, the side sliding door or the front portion of the 60/40 side swing-out door. With this feature, you can lock these doors so they can’t be opened from the inside by passengers. Rear Cargo Door Move the lever down to engage the security feature. Move the lever up to return the door locks to normal operation When a door is locked, the inside door handle will not work. Cargo Door Relocking This feature protects the owner from having an unsecured side cargo door. If the side cargo door is open when the lock button is pressed on the door or the remote keyless entry transmitter, all doors will lock and then relock again after the cargo door is closed. If the cargo door is not closed within several minutes, the relock will not occur. 2-8 Move the button to the left to engage the security feature. Move the button to the right to return the door locks to normal operation. Move the button to the right to engage the security feature. Move the button to the left to return the door locks to normal operation. Passenger Side 60/40 Swing-Out Side Door Driver’s Side 60/40 Swing-Out Side Door 2-9 Sliding Side Door Move the button up to engage the security feature. Move the button down to return the door locks to normal operation. Side Sliding Door Lockout Protection This feature protects you from locking your key in the vehicle when the key is in the ignition and a door is open. If the power lock switch is pressed when either the driver’s, passenger’s, or rear door is open, all the doors will lock and then the driver’s door will unlock. This feature does not include the side cargo door. 2-10 To open the sliding side door from outside, pull the handle toward the rear of the vehicle. Then, slide the door open. To close the sliding side door from outside, use the outside door handle to slide the door toward the front of the vehicle. When the door slides closed completely, it will be ﬂush with the side of the body. To open the sliding door from inside, turn the handle upward and toward the rear of the vehicle. Then, slide the door toward the rear of the vehicle to open it. 2-11 60/40 Swing-Out Side Door To close the sliding door from inside, grasp the inside handle and slide the door toward the front of the vehicle to a closed position. Make sure the door is completely closed before driving away. To open the front portion of a 60/40 door from the outside, pull out on the handle and pull it toward you. 2-12 To open the front portion of a 60/40 door from the inside, pull the handle toward you and push open the door. To open the rear portion of a 60/40 door from the outside, pull the handle on the side of the rear door and pull it toward you. To close the 60/40 side doors, close the rear door ﬁrst. Then close the front door. Check to make sure that both doors are completely closed. The front side swing-out door has a check strap assembly in the door frame to keep the door from opening beyond 90 degrees. To open the door beyond 90 degrees, close the door partially, pull the check strap toward you and then open the door. When you close the door, the check strap will automatically re-engage. 2-13 CAUTION: (Continued) (cid:127) Young children who get into unlocked vehicles may be unable to get out. A child can be overcome by extreme heat and can suffer permanent injuries or even death from heat stroke. Always lock your vehicle whenever you leave it. (cid:127) Outsiders can easily enter through an unlocked door when you slow down or stop your vehicle. Locking your doors can help prevent this from happening. Rear Doors {CAUTION: Unlocked doors can be dangerous. (cid:127) Passengers — especially children — can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked. So, wear safety belts properly and lock the doors whenever you drive. CAUTION: (Continued) 2-14 To open the rear doors from the outside, pull the handle toward you to open the passenger’s side rear door ﬁrst. To open the driver’s side rear door, pull the latch release at the inside edge of the door. To close the rear doors, close the driver side rear door ﬁrst. Then, close the passenger side rear door. Check to make sure both doors are completely closed. 2-15 Windows {CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather. 2-16 Manual Windows To operate your manual windows, turn the hand crank on each door to raise or lower your side door windows. Power Windows If you have power windows, the controls are located on each of the side doors. The driver’s door has a switch for the passenger window as well. Your power windows will work when the ignition has been turned to RUN or ACCESSORY, or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 2-20. Press the bottom of the switch with the power window symbol on it to lower the window. Press the top of the switch with the power window symbol on it to raise the window. Express-Down The driver’s window switch also has an express-down feature that allows the window to be lowered without holding the switch. Press and hold the side of the window switch marked AUTO for one second to activate the express-down mode. This mode can be cancelled at any time by pressing the opposite side of the switch. To open the window part way, lightly tap the switch until the window is at the desired position. 2-17 Swing-Out Windows Side Swing-Out Window To open the side door swing-out windows, pull up on the latch at the edge of the window. Swing the window out and push down on the latch to lock the window into place. To close the window, pull the latch toward you and push down on the latch to lock it. Your vehicle also has rear swing out windows. 2-18 Rear-Swing Out Windows The rear swing-out windows work the same way as the side swing out windows, but the latch is located at the bottom edge of the window. Sun Visors To block out glare, you can swing down the visors. You can also swing them from side to side. Visor Vanity Mirror Some visors have mirrors built in, with or without lamps. Just lift the mirror cover on each visor to turn the lamps on, if you have them. Theft-Deterrent Systems Vehicle theft is big business, especially in some cities. Although your vehicle has a number of theft-deterrent features, we know that nothing we put on it can make it impossible to steal. Passlock® Your vehicle is equipped with the Passlock® theft-deterrent system. Passlock® is a passive theft-deterrent system. Passlock® enables fuel if the ignition lock cylinder is turned with a valid key. If a correct key is not used or the ignition lock cylinder is tampered with, fuel is disabled. During normal operation, the SECURITY light will go off approximately ﬁve seconds after the key is turned to RUN. See Security Light on page 3-37. If the engine stalls and the SECURITY light ﬂashes, wait until the light stops ﬂashing before trying to restart the engine. Remember to release the key from START as soon as the engine starts. If the engine is running and the SECURITY light comes on, you will be able to restart the engine if you turn the engine off. However, your Passlock® system is not working properly and must be serviced by your dealer. Your vehicle is not protected by Passlock® at this time. You may also want to check the fuse. See Fuses and Circuit Breakers on page 5-93. See your dealer for service. Starting and Operating Your Vehicle New Vehicle Break-In Notice: Your vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: (cid:127) Keep your speed at 55 mph (88 km/h) or less for the ﬁrst 500 miles (805 km). (cid:127) Do not drive at any one speed — fast or slow — for the ﬁrst 500 miles (805 km). Do not make full-throttle starts. (cid:127) Avoid making hard stops for the ﬁrst 200 miles (322 km) or so. During this time your new brake linings are not yet broken in. Hard stops with new linings can mean premature wear and earlier replacement. Follow this breaking-in guideline every time you get new brake linings. (cid:127) Do not tow a trailer during break-in. See Towing a Trailer on page 4-36 for more information. 2-19 B (Accessory): This position lets you use things like the radio and the windshield wipers when the engine is off. Notice: Lengthy operation of features such as the radio in the accessory ignition position may drain the battery and prevent your vehicle from starting. Do not operate your vehicle in the accessory ignition position for a long period of time. C (Run): This is the position for driving. D (Start): This position starts the engine. Retained Accessory Power (RAP) The Retained Accessory Power (RAP) feature will allow certain features on your vehicle to continue to work for up to 10 minutes after the ignition key is turned to LOCK or until one of the doors is opened. Ignition Positions Use the key to turn the ignition switch to four different positions. A (Lock): This position locks the ignition and transmission. It is a theft-deterrent feature. You will only be able to remove the key when the ignition is turned to LOCK. Notice: Using a tool to force the key from the ignition switch could cause damage or break the key. Use the correct key and turn the key only with your hand. Make sure the key is in all the way. If none of this works, then your vehicle needs service. 2-20 Starting Your Engine Move your shift lever to PARK (P) or NEUTRAL (N). Your engine will not start in any other position — that is a safety feature. To restart when you are already moving, use NEUTRAL (N) only. Notice: Do not try to shift to PARK (P) if your vehicle is moving. If you do, you could damage the transmission. Shift to PARK (P) only when your vehicle is stopped. 1. With your foot off the accelerator pedal, turn the ignition key to START. When the engine starts, let go of the key. The idle speed will go down as your engine gets warm. Notice: Holding your key in START for longer than 15 seconds at a time will cause your battery to be drained much sooner. And the excessive heat can damage your starter motor. Wait about 15 seconds between each try to help avoid draining your battery or damaging your starter. 2. If it does not start within 10 seconds, push the accelerator pedal all the way to the ﬂoor, while you hold the ignition key in START. When the engine starts, let go of the key and let up on the accelerator pedal. Wait about 15 seconds between each try. When starting your engine in very cold weather (below 0°F or −18°C), do this: 1. With your foot off the accelerator pedal, turn the ignition key to START and hold it there up to 15 seconds. When the engine starts, let go of the key. 2. If your engine still will not start, or starts but then stops, it could be ﬂooded with too much gasoline. Try pushing your accelerator pedal all the way to the ﬂoor and holding it there as you hold the key in START for about three seconds. When the engine starts, let go of the key and accelerator. If the vehicle starts brieﬂy but then stops again, do the same thing, but this time keep the pedal down for ﬁve or six seconds. This clears the extra gasoline from the engine. Notice: Your engine is designed to work with the electronics in your vehicle. If you add electrical parts or accessories, you could change the way the engine operates. Before adding electrical equipment, check with your dealer. If you do not, your engine might not perform properly. 2-21 Fuel Regulator Your vehicle has a fuel regulator that shuts the fuel off when the engine reaches 5,600 rpm. Engine Coolant Heater In very cold weather, 0°F (−18°C) or colder, the engine coolant heater can help. You will get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle. At temperatures above 32°F (0°C), use of the coolant heater is not required. Your vehicle may also have an internal thermostat in the plug end of the cord. This will prevent operation of the engine coolant heater when the temperature is at or above 0°F (−18°C) as noted on the cord. To Use the Engine Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. The cord for the engine coolant heater is located on the driver’s side of the engine compartment and is attached to the hose for the power steering reservoir. 3. Plug it into a normal, grounded 110-volt AC outlet. 2-22 {CAUTION: Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a ﬁre. You could be seriously injured. Plug the cord into a properly grounded three-prong 110-volt AC outlet. If the cord will not reach, use a heavy-duty three-prong extension cord rated for at least 15 amps. 4. Before starting the engine, be sure to unplug and store the cord as it was before to keep it away from moving engine parts. If you do not, it could be damaged. How long should you keep the coolant heater plugged in? The answer depends on the outside temperature, the kind of oil you have, and some other things. Instead of trying to list everything here, we ask that you contact your dealer in the area where you will be parking your vehicle. The dealer can give you the best advice for that particular area. Automatic Transmission Operation There are several different positions for your shift lever. PARK (P): This position locks your rear wheels. It is the best position to use when you start your engine because your vehicle cannot move easily. {CAUTION: It is dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set your parking brake and move the shift lever to PARK (P). See Shifting Into Park (P) on page 2-26. If you are pulling a trailer, see Towing a Trailer on page 4-36. Ensure the shift lever is fully in PARK (P) before starting the engine. Your vehicle has an automatic transmission shift lock control system. With the ignition in RUN, you must fully apply your regular brakes before you can shift from PARK (P). If you cannot shift out of PARK (P), ease pressure on the shift lever and push the shift lever all the way into PARK (P) as you continue pressing the brake pedal. Then move the shift lever into the gear you want. See Shifting Out of Park (P) on page 2-27. REVERSE (R): Use this gear to back up. Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transmission. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped. To rock your vehicle back and forth to get out of snow, ice or sand without damaging your transmission, see If You Are Stuck: In Sand, Mud, Ice or Snow on page 4-30. NEUTRAL (N): In this position, your engine does not connect with the wheels. To restart when you are already moving, use NEUTRAL (N) only. Also, use NEUTRAL (N) when your vehicle is being towed. 2-23 {CAUTION: Shifting into a drive gear while your engine is running at high speed is dangerous. Unless your foot is ﬁrmly on the brake pedal, your vehicle could move very rapidly. You could lose control and hit people or objects. Do not shift into a drive gear while your engine is running at high speed. Notice: Shifting out of PARK (P) or NEUTRAL (N) with the engine running at high speed may damage the transmission. The repairs would not be covered by your warranty. Be sure the engine is not running at high speed when shifting your vehicle. DRIVE (D): This position is for normal driving. If you need more power for passing, and you are: (cid:127) Going less than about 35 mph (55 km/h), push your accelerator pedal about halfway down. (cid:127) Going about 35 mph (55 km/h) or more, push the accelerator all the way down. You will shift down to the next gear and have more power. 2-24 THIRD (3): This position is also used for normal driving, however, it offers more power and lower fuel economy than DRIVE (D). You should use THIRD (3) when carrying a heavy load or driving on steep hills. You should use THIRD (3) (or, as you need to, a lower gear) when towing a trailer to minimize heat build-up and extend the life of your transmission. SECOND (2): This position gives you more power but lower fuel economy than THIRD (3). You can use SECOND (2) on hills. It can help control your speed as you go down steep mountain roads, but then you would also want to use your brakes off and on. If you manually select SECOND (2), the transmission will drive in SECOND (2). You may use this feature for reducing torque to the rear wheels when you are trying to start your vehicle from a stop on slippery road surfaces. FIRST (1): This position gives you even more power but lower fuel economy than SECOND (2). You can use it on very steep hills, or in deep snow or mud. If the shift lever is put in FIRST (1), the transmission will not shift into ﬁrst gear until the vehicle is going slowly enough. Notice: Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transmission. If you are stuck, do not spin the tires. When stopping on a hill, use the brakes to hold the vehicle in place. All-Wheel Drive If your vehicle has all-wheel drive, your engine’s driving power is sent to all four wheels for extra traction when needed. This is like four-wheel drive, but there is no separate lever or switch to engage or disengage the front axle. It is fully automatic, and adjusts itself as needed for road conditions. You may experience a brief vehicle vibration upon acceleration when driving in slippery conditions. This is normal and is an indication that the all-wheel drive system is functioning properly. Parking Brake To set the parking brake, hold the regular brake pedal down with your right foot. Push down the parking brake pedal with your left foot. If the ignition is on, the brake system warning light will come on. To release the parking brake, hold the regular brake pedal down. Pull the handle, located just above the parking brake pedal, marked BRAKE RELEASE to release the parking brake. If the ignition is on when the parking brake is released, the brake system warning light will go off. Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Verify that the parking brake is fully released and the brake warning light is off before driving. If you are towing a trailer and are parking on any hill, see Towing a Trailer on page 4-36. That section shows what to do ﬁrst to keep the trailer from moving. 2-25 Shifting Into Park (P) {CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, use the steps that follow. If you are pulling a trailer, see Towing a Trailer on page 4-36. 1. Hold the brake pedal down with your right foot and set the parking brake with your left foot. 2. Move the shift lever into PARK (P) by pulling the shift lever toward you and moving it up as far as it will go. 3. Turn the ignition key to LOCK. 4. Remove the key and take it with you. If you can leave your vehicle with the ignition key in your hand, your vehicle is in PARK (P). 2-26 Leaving Your Vehicle With the Engine Running {CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch ﬁre. You or others could be injured. Do not leave your vehicle with the engine running. If you have to leave your vehicle with the engine running, be sure your vehicle is in PARK (P) and the parking brake is ﬁrmly set before you leave it. After you move the shift lever into PARK (P), hold the regular brake pedal down. Then, see if you can move the shift lever away from PARK (P) without ﬁrst pulling it toward you. If you can, it means that the shift lever was not fully locked into PARK (P). Torque Lock If you are parking on a hill and you do not shift your vehicle into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may ﬁnd it difficult to pull the shift lever out of PARK (P). This is called torque lock. To prevent torque lock, set the parking brake and then shift into PARK (P) properly before you leave the driver’s seat. To ﬁnd out how, see Shifting Into Park (P) on page 2-26. When you are ready to drive, move the shift lever out of PARK (P) before you release the parking brake. If torque lock does occur, you may need to have another vehicle push yours a little uphill to take some of the pressure from the parking pawl in the transmission, so you can pull the shift lever out of PARK (P). Shifting Out of Park (P) Your vehicle has an automatic transmission shift lock control system. You have to fully apply your regular brakes before you can shift from PARK (P) when the ignition is in RUN. See Automatic Transmission Operation on page 2-23. If you cannot shift out of PARK (P), ease pressure on the shift lever and push the shift lever all the way up into PARK (P) as you maintain brake application. Then, move the shift lever into the gear you want. If you ever hold the brake pedal down but still cannot shift out of PARK (P), try this: 1. Turn the key to OFF. 2. Apply and hold the brake until the end of Step 4. 3. Shift to NEUTRAL (N). 4. Start the vehicle and then shift to the drive gear you want. 5. Have the system ﬁxed as soon as you can. 2-27 Parking Over Things That Burn Engine Exhaust {CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: (cid:127) Your exhaust system sounds strange or different. (cid:127) Your vehicle gets rusty underneath. (cid:127) Your vehicle was damaged in a collision. (cid:127) Your vehicle was damaged when driving over high points on the road or over road debris. (cid:127) Repairs were not done correctly. (cid:127) Your vehicle or exhaust system had been modiﬁed improperly. If you ever suspect exhaust is coming into your vehicle: (cid:127) Drive it only with all the windows down to blow out any CO; and (cid:127) Have your vehicle ﬁxed immediately. {CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass or other things that can burn. 2-28 Running Your Engine While You Are Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. {CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. See the earlier caution under Engine Exhaust on page 2-28. Also, idling in a closed-in place can let deadly carbon monoxide (CO) into your vehicle even if the climate control fan is at the highest setting. One place this can happen is a garage. Exhaust — with CO — can come in easily. NEVER park in a garage with the engine running. Another closed-in place can be a blizzard. See Winter Driving on page 4-26. {CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set your parking brake and move the shift lever to PARK (P). Follow the proper steps to be sure your vehicle will not move. See Shifting Into Park (P) on page 2-26. If you are pulling a trailer, see Towing a Trailer on page 4-36. 2-29 Mirrors Outside Camper-Type Mirrors If your vehicle is equipped with the camper-type mirrors, they can be adjusted so you can have a clear view of any objects behind you. Manual Rearview Mirror Inside Day/Night Rearview Mirror Pull the tab under the mirror toward you to reduce glare from headlamps behind you after dark. Push the tab away from you to restore the mirror to the original position. If you have a cargo van without the rear door glass, your vehicle may not have a rearview mirror. Outside Manual Mirror Adjust your outside mirrors so you can see a little of the side of your vehicle, and have a clear view of objects behind you. Some mirrors can be folded in to enter narrow passageways. 2-30 1. To adjust the mirrors when towing a trailer, turn the mirror by pushing the mirror head toward the front of the vehicle. Outside Power Mirrors If the vehicle has power mirrors, the control is located on the driver’s side door. 2. Turn the mirror head so that it swings further outboard and adjust the mirror surface as needed. Select each mirror by turning the knob clockwise for the passenger’s side mirror or counterclockwise for the driver’s side mirror. The center position is neutral. Then, adjust the mirror angle by moving the knob in the desired direction. 2-31 Outside Convex Mirror Your passenger’s side mirror may be convex. A convex mirror’s surface is curved so you can see more from the driver’s seat. {CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes. Outside Heated Mirrors Your outside mirrors can be defrosted by pressing the button located near the fan control. An indicator light in the button will light while the heated outside mirrors are activated. Your rear window defogger comes on while the heated mirrors are on. If your vehicle has a rear window defogger, see “Rear Window Defogger” in Climate Control System on page 3-18. 2-32 OnStar® System OnStar® uses global positioning system (GPS) satellite technology, wireless communications, and call centers to provide you with a wide range of safety, security, information, and convenience services. A complete OnStar® user’s guide and the terms and conditions of the OnStar® Subscription Service Agreement are included in the vehicle’s glove box literature. For more information, visit www.onstar.com or www.onstarcanada.com. Contact OnStar® at 1-888-4-ONSTAR (1-888-466-7827), or press the OnStar® button to speak to an OnStar® advisor 24 hours a day, 7 days a week. Terms and conditions of the Subscription Service Agreement can be found at www.onstar.com or www.onstarcanada.com. OnStar® Services For new vehicles equipped with OnStar®, the Safe and Sound Plan is included for the ﬁrst year. You can extend this plan beyond the ﬁrst year, or upgrade to the Directions and Connections Plan to meet your needs. For more information, press the OnStar® button to speak with an advisor. Safe and Sound Plan (cid:127) Automatic Notiﬁcation of Airbag Deployment (cid:127) Emergency Services (cid:127) Roadside Assistance (cid:127) Stolen Vehicle Tracking (cid:127) AccidentAssist (cid:127) Remote Door Unlock/Vehicle Alert (cid:127) Remote Diagnostics (cid:127) Online Concierge Directions and Connections Plan (cid:127) All Safe and Sound Plan Services (cid:127) Driving Directions (cid:127) RideAssist Information and Convenience Services 2-33 (cid:127) OnStar® Personal Calling As an OnStar® subscriber, the Personal Calling capability is available if your hand-held cell phone is lost, forgotten, or has a low battery. It is a hands-free wireless phone that is integrated into the vehicle. Calls can be placed nationwide using simple voice commands with no additional contracts and no additional roaming charges. To ﬁnd out more about OnStar® Personal Calling, refer to the OnStar® user’s guide in the vehicle’s glove box or visit www.onstar.com or www.onstarcanada.com; or speak with an OnStar® advisor by pressing the OnStar® button or by calling 1-888-4-ONSTAR (1-888-466-7827). OnStar® Virtual Advisor Virtual Advisor is a feature of OnStar® Personal Calling that uses minutes to access up-to-date weather and traffic reports for your area, news and sports updates, stock quotes, entertainment and more. You are also able to listen and reply to your E-mail through your vehicle’s audio system. Customize your information proﬁle at www.myonstar.com. See the OnStar® user’s guide for more information. Storage Areas Your front storage compartment is at the center of the instrument panel extension, by the ﬂoor. To open the compartment, pull up on the latch. The compartment will open automatically. Storage compartments may also be included on the inside of each front door. 2-34 Section 3 Instrument Panel Instrument Panel Overview ...............................3-4 Hazard Warning Flashers ................................3-6 Other Warning Devices ...................................3-6 Horn .............................................................3-6 Tilt Wheel .....................................................3-6 Turn Signal/Multifunction Lever .........................3-7 Turn and Lane-Change Signals ........................3-8 Headlamp High/Low-Beam Changer ..................3-9 Flash-to-Pass .................................................3-9 Windshield Wipers ..........................................3-9 Windshield Washer .......................................3-10 Cruise Control ..............................................3-10 Exterior Lamps .............................................3-13 Headlamps on Reminder ................................3-14 Daytime Running Lamps (DRL) .......................3-14 Instrument Panel Brightness ...........................3-15 Dome Lamps ...............................................3-15 Dome Lamp Override ....................................3-15 Entry Lighting ...............................................3-16 Exit Lighting .................................................3-16 Reading Lamps ............................................3-16 Battery Run-Down Protection ..........................3-16 Accessory Power Outlets ...............................3-16 Ashtrays and Cigarette Lighter ........................3-17 Climate Controls ............................................3-18 Climate Control System .................................3-18 Outlet Adjustment .........................................3-20 Rear Heating System ....................................3-21 Rear Air Conditioning and Heating System .......3-22 Warning Lights, Gages, and Indicators ............3-23 Instrument Panel Cluster ................................3-24 Speedometer and Odometer ...........................3-25 Trip Odometer ..............................................3-25 Engine Speed Limiter ....................................3-25 Safety Belt Reminder Light .............................3-25 Airbag Readiness Light ..................................3-26 Airbag Off Light ............................................3-27 Charging System Light ..................................3-28 Voltmeter Gage ............................................3-29 Brake System Warning Light ..........................3-29 Anti-Lock Brake System Warning Light .............3-31 StabiliTrak Not Ready Light ............................3-31 StabiliTrak Indicator Light ...............................3-32 Engine Coolant Temperature Gage ..................3-32 Malfunction Indicator Lamp .............................3-33 Oil Pressure Gage ........................................3-35 Change Engine Oil Light ................................3-36 3-1 Section 3 Instrument Panel Radio with CD ..............................................3-44 Radio with Cassette and CD ..........................3-49 Radio with Six-Disc CD .................................3-62 Theft-Deterrent Feature (Non-RDS Radios) .....................................3-72 Theft-Deterrent Feature (RDS Radios) ...........................................3-72 Radio Reception ...........................................3-72 Care of Your Cassette Tape Player .................3-73 Care of Your CDs .........................................3-74 Care of Your CD Player ................................3-74 Fixed Mast Antenna ......................................3-74 Chime Level Adjustment ................................3-74 Security Light ...............................................3-37 Cruise Control Light ......................................3-37 Reduced Engine Power Light .........................3-38 Highbeam On Light .......................................3-38 Daytime Running Lamps (DRL) Indicator Light ..3-38 Tow/Haul Mode Light ....................................3-39 Check Gages Warning Light ...........................3-39 Fuel Gage ...................................................3-40 Audio System(s) .............................................3-41 Setting the Time for Radios without Radio Data Systems (RDS) ..................................3-41 Setting the Time for Radios with Radio Data Systems (RDS) .........................................3-41 AM-FM Radio ...............................................3-42 3-2 ✍ NOTES 3-3 Instrument Panel Overview 3-4 The main components of your instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 3-20. B. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-7. C. Instrument Panel Cluster. See Instrument Panel Cluster on page 3-24. D. Shift Lever. See Starting Your Engine on page 2-21. E. Climate Control System. See Climate Control System on page 3-18. F. Audio System(s). See Audio System(s) on page 3-41. G. Exterior Lamp Controls. See Exterior Lamps on page 3-13. H. Tow/Haul Mode Button. See “Tow/Haul Mode” under Towing a Trailer on page 4-36. I. Rear Heating System (If Equipped). See Rear Heating System on page 3-21. J. Accessory Power Outlets/Cigarette Lighter. See Accessory Power Outlets on page 3-16 and Ashtrays and Cigarette Lighter on page 3-17. K. Airbag Off Switch. See Airbag Off Switch on page 1-69. L. Storage Compartment. See Storage Areas on page 2-34. M. StabiliTrak® Button. See StabiliTrak® System on page 4-9. 3-5 Hazard Warning Flashers Your hazard warning ﬂashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will ﬂash on and off. Other Warning Devices If you carry reﬂective triangles, you can set them up at the side of the road about 300 feet (100 m) behind your vehicle. The hazard warning ﬂasher button is located on top of the steering column. Horn Press the horn symbol in the middle of the steering wheel to sound the horn. Your hazard warning ﬂashers work no matter what position your key is in, and even if the key is not in the ignition. Press the button to make the front and rear turn signal lamps ﬂash on and off. Press the button again to turn the ﬂashers off. When the hazard warning ﬂashers are on, your turn signals will not work. Tilt Wheel A tilt steering wheel allows you to adjust the steering wheel before you drive. You can also raise it to the highest level to give your legs more room when you enter and exit the vehicle. The lever is located on the lower left side of the steering column. 3-6 To tilt the wheel, hold the steering wheel and pull the lever. Move the steering wheel to a comfortable level, then release the lever to lock the wheel in place. Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: (cid:127) G Turn and Lane Change Signals. Turn and Lane-Change Signals on page 3-8. (cid:127) 3 Headlamp High/Low-Beam Changer. Headlamp High/Low-Beam Changer on page 3-9. Flash-to-Pass Feature. See Flash-to-Pass on page 3-9. (cid:127) N Windshield Wipers. See Windshield Wipers on page 3-9. 3-7 (cid:127) (cid:127) L Windshield Washer. See Windshield Washer on page 3-10. (cid:127) I Cruise Control. Cruise Control on page 3-10. For information on the exterior lamps, see Exterior Lamps on page 3-13 later in this section. Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is ﬁnished, the lever will return automatically. An arrow on the instrument panel cluster will ﬂash in the direction of the turn or lane change. To signal a lane change, just raise or lower the lever until the arrow starts to ﬂash. Hold it there until you complete your lane change. The lever will return by itself when you release it. If you move the lever all the way up or down, and the arrow ﬂashes at twice the normal rate, a signal bulb may be burned out and other drivers may not see your turn signal. If a bulb is burned out, replace it to help avoid an accident. If the arrows don’t go on at all when you signal a turn, check for burned-out bulbs or a blown fuse. See Fuses and Circuit Breakers on page 5-93. Turn Signal On Chime If your turn signal is left on for more than 3/4 of a mile (1.2 km), a chime will sound at each ﬂash of the turn signal. To turn off the chime, move the turn signal lever to the off position. 3-8 Headlamp High/Low-Beam Changer 23(Headlamp High/Low-Beam Changer): To change the headlamps from low to high beam, pull the multifunction lever all the way toward you. Then release it. When the high beams are on, this light on the instrument panel cluster also will be on. Flash-to-Pass This feature allows you to use your high-beam headlamps to signal a driver in front of you that you want to pass. It works even if your headlamps are off. To use it, pull the turn signal lever toward you, but not so far that you hear it click. If your headlamps are off or on low-beam, your high-beam headlamps will turn on and stay on as long as you hold the lever toward you and the high-beam indicator on the instrument panel will come on. Release the lever to turn the high-beam headlamps off. Windshield Wipers You control the windshield wipers by turning the band with the wiper symbol on it. 8(Mist): For a single wiping cycle, turn the band to mist. Hold it there until the wipers start, then let go. The wipers will stop after one wipe. If you want more wipes, hold the band on mist longer. Delay: You can set the wiper speed for a long or short delay between wipes. This can be very useful in light rain or snow. Turn the band to choose the delay time. The closer to the top of the lever, the shorter the delay. d (Low Speed): For steady wiping at low speed, turn the band away from you to the ﬁrst solid band past the delay settings. position. For high-speed wiping, turn the band further, to the second solid band past the delay settings. To stop the wipers, move the band to off position. a (High Speed): For high-speed wiping, turn the band further, to the second solid band past the delay settings. 9 (Off): To stop the wipers, move the band to off. Be sure to clear ice and snow from the wiper blades before using them. If they’re frozen to the windshield, carefully loosen or thaw them. If your blades do become worn or damaged, get new blades or blade inserts. 3-9 Windshield Washer L(Washer Fluid): There is a paddle marked with the windshield washer symbol at the top of the multifunction lever. To spray washer ﬂuid on the windshield, push the paddle. The wipers will clear the window and then either stop or return to your preset speed. {CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. Cruise Control If your vehicle has cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h). If you apply your brakes, the cruise control will disengage. {CAUTION: Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use your cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause needless wheel spinning, and you could lose control. Do not use cruise control on slippery roads. 3-10 9(Off): This position turns the system off. R(On): This position activates the system. S (Resume/Accelerate): Push the lever to this symbol to make the vehicle accelerate or resume to a previously set speed. T (Set): Press this button to set the speed. Setting Cruise Control {CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control. 1. Move the cruise control switch to on. 2. Get up to the speed you want. 3. Press in the set button at the end of the lever and release it. 4. Take your foot off the accelerator pedal. The CRUISE light on the instrument panel will illuminate when the cruise control is engaged. 3-11 Resuming a Set Speed Suppose you set your cruise control at a desired speed and then you apply the brake. This, of course, disengages the cruise control. But you don’t need to reset it. Once you’re going about 25 mph (40 km/h) or more, you can move the cruise control switch from on to resume/accelerate brieﬂy. You’ll go right back up to your chosen speed and stay there. If you hold the switch at resume/accelerate brieﬂy, the vehicle will keep going faster until you release the switch or apply the brake. So unless you want to go faster, don’t hold the switch at resume/accelerate. Increasing Speed While Using Cruise Control There are two ways to go to a higher speed: (cid:127) Use the accelerator pedal to get to the higher speed. Press the set button at the end of the lever, then release the button and the accelerator pedal. You’ll now cruise at the higher speed. (cid:127) Move the cruise switch from on to resume/accelerate. Hold it there until you get up to the speed you want, and then release the switch. To increase your speed in very small amounts, move the switch to resume/accelerate brieﬂy. Each time you do this, your vehicle will go about 1 mph (1.6 km/h) faster. Reducing Speed While Using Cruise Control (cid:127) Press and hold the set button at the end of the lever until you reach the lower speed you want, then release it. To slow down in very small amounts, press the set button brieﬂy. Each time you do this, you’ll go about 1 mph (1.6 km/h) slower. Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase your speed. When you take your foot off the pedal, your vehicle will slow down to the cruise control speed you set earlier. 3-12 (cid:127) Using Cruise Control on Hills How well your cruise control will work on hills depends upon your speed, load and the steepness of the hills. When going up steep hills, you may want to step on the accelerator pedal to maintain your speed. When going downhill, you may have to brake or shift to a lower gear to keep your speed down. Of course, applying the brake takes you out of cruise control. Many drivers ﬁnd this to be too much trouble and don’t use cruise control on steep hills. Ending Cruise Control There are three ways to turn off the cruise control: (cid:127) Step lightly on the brake pedal. (cid:127) Move the cruise control switch to off. If your vehicle has the Stabilitrak® feature, cruise control will deactivate if road conditions cause Stabilitrak® to activate. Erasing Speed Memory When you turn off the cruise control or the ignition, your cruise control set speed memory is erased. Exterior Lamps The control on the driver’s side of your instrument panel operates the exterior lamps. The exterior lamp control has four positions: Ø (Defeat): Turn the control to this position to turn off the DRL. i (Daytime Running Lamps (DRL)): Turning the control to this position selects the DRL. When the vehicle is shifted out of PARK (P), the instrument panel lamps will illuminate and the DRL will turn on, unless defeated. When the DRL are active, the DRL indicator will illuminate. 3-13 (cid:127) ; (Parking Lamps): Turn the control to this position to turn on the parking lamps, together with the following: Instrument Panel Lights (cid:127) Daytime Running Lamps (DRL) (Canada) (cid:127) Sidemarker Lamps Taillamps License Plate Lamps If the DRL are active when the control is turned to this position, the DRL will turn off. For vehicles ﬁrst sold in Canada, the DRL will remain active along with the lamps mentioned above. 5 (Headlamps): Turn the control to this position to turn on the headlamps together with the parking lamps and turn off the daytime running lamps. You can switch your headlamps from high to low-beam by pulling the turn signal/high-beam lever toward you. A circuit breaker protects your headlamps. If you have an electrical overload, your headlamps will ﬂicker on and off. Have your headlamp wiring checked right away if this happens. Headlamps on Reminder A reminder chime will sound when your control is turned to the headlamps or parking lamps position, your key is out of the ignition, and your driver’s door is open. To disable the chime, turn the control to the Daytime Running Lamp (DRL) position and then back to the parking lamps or headlamps position. Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional daytime running lamps are required on all vehicles ﬁrst sold in Canada. The DRL system will come on when the following conditions are met: the ignition is on, the exterior lamps control is in DRL mode and not in the defeat position. When the DRL are on, only your headlamps will be on. The taillamps, sidemarker and other lamps won’t be on. The instrument panel will be lit. 3-14 (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) When you turn the headlamp switch off, the headlamps will go off, and your DRL lamps will illuminate. To turn off the DRL, turn the exterior lamp control to the defeat position or shift into PARK (P). The DRL will stay off until the control is toggled again or the vehicle is shifted out of PARK (P). This procedure applies only to vehicles ﬁrst sold in the United States. Instrument Panel Brightness Press this knob located next to the exterior lamps knob to extend it, and then turn it to adjust the instrument panel brightness. Dome Lamps The dome lamps will automatically come on when a door is opened and turn off shortly after all doors are closed. Dome Lamp Override You can use the dome lamp override button, located below the exterior lamp control, to override the automatic operation of the dome lamps. Turn the knob all the way clockwise to turn on the interior lamps. Press the knob back into its stored position when not in use. To turn the automatic operation of the lamps off, press the button. The dome lamps will remain off while a door is open. To return the lamps to automatic operation, press the button again. While pressed in, this will override the illuminated entry feature unless you use your keyless entry transmitter to unlock the vehicle. 3-15 Entry Lighting Your vehicle is equipped with an illuminated entry feature. When a door is opened, the dome lamps will come on if the dome override button is in the out position. If the dome override button is pressed in, the lamps will not come on. When the door is closed, the interior lamps will remain on for a period of 15 seconds or until the vehicle is started. Exit Lighting With exit lighting, the interior lamps will come on for a period of 40 seconds when you remove the key from the ignition. The lamps will not come on if the dome override button is pressed in. Reading Lamps To turn on the reading lamps, press the button located next to each lamp. To turn them off, press the button again. Battery Run-Down Protection This feature shuts off the exterior and interior lamps if they are left on after the ignition is turned off. All exterior lamps will shut off after 10 minutes. Interior cargo lamps will shut down after 20 minutes and all other interior lamps after 10 minutes. Accessory Power Outlets With accessory power outlets you can plug in auxiliary electrical equipment such as a cellular telephone or CB radio. Your vehicle may have two accessory power outlets. If your vehicle has a cigarette lighter/accessory power outlet, it is located on the driver’s side of the front storage compartment. The other accessory power outlet is located on the passenger’s side of the front storage compartment. To use the outlet, lift the cover. When not using it, always close the cover. 3-16 Certain power accessory plugs may not be compatible to the accessory power outlet and could result in blown vehicle or adapter fuses. If you experience a problem, see your dealer for additional information on the accessory power plugs. Notice: Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should. The repairs would not be covered by your warranty. Check with your dealer before adding electrical equipment. When adding electrical equipment, be sure to follow the proper installation instructions included with the equipment. Notice: damage not covered by your warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only. Improper use of the power outlet can cause If you put papers or other ﬂammable items Ashtrays and Cigarette Lighter Your vehicle may have this feature. The front ashtray can be placed in the instrument panel extension at the center of the instrument panel. Lift up on the ashtray door to open it. Notice: in the ashtray, hot cigarettes or other smoking materials could ignite them and possibly damage your vehicle. Never put ﬂammable items in the ashtray. To use the cigarette lighter, push it in all the way and let go. When it’s ready, it will pop back out by itself. Notice: Holding a cigarette lighter in while it is heating will not allow the lighter to back away from the heating element when it is hot. Damage from overheating may occur to the lighter or heating element, or a fuse could be blown. Do not hold a cigarette lighter in while it is heating. Do not use anything other than the cigarette lighter in the heating element. 3-17 Climate Controls Climate Control System With this system you can control the heating, cooling and ventilation for your vehicle. Turn the right knob clockwise or counterclockwise to direct the airﬂow inside of your vehicle. To change the current mode, select one of the following: H (Vent): This mode directs air to the instrument panel outlets. ) (Bi-Level): This mode directs about half of the air to the instrument panel outlets, then directs most of the remaining air to the ﬂoor outlets. Some air may be directed toward the windshield. 3-18 6 (Floor): This mode directs most of the air to the ﬂoor outlets with some air directed to the outboard outlets (for the side windows) and some air directed to the windshield. The right knob can also be used to select the defrost and defog modes. Information on defogging and defrosting can be found later in this section. 9 (Fan): Turn the left knob clockwise or counterclockwise to increase or decrease the fan speed. Temperature Control: Turn the center knob clockwise or counterclockwise to increase or decrease the temperature inside your vehicle. If your vehicle has air conditioning, your heating/air conditioning controls will look like this: On hot days, open the windows to let hot inside air escape; then close them. This helps to reduce the time it takes for your vehicle to cool down. It also helps the system to operate more efficiently. A/C (Air Conditioning): This setting will begin to cool and dehumidify the air inside of your vehicle. MAX A/C (Maximum Air Conditioning): Turn the right knob to MAX A/C for maximum cooling. This setting cools the air the fastest, by recirculating the inside air. Defogging and Defrosting Fog on the inside of windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control is used properly. There are two modes to clear fog or frost from your windshield and side windows. Use the defog mode to clear the windows of fog or moisture and warm the passengers. Use the defrost mode to remove fog or frost from the windshield more quickly. For best results, clear all snow and ice from the windshield before defrosting. Turn the knob on the right of the climate control panel to select the defog or defrost mode. -(Defog): With this setting, the outside air comes out of both the ﬂoor and defroster outlets. Adjust the temperature knob for warmer or cooler air. The air conditioning compressor may operate in this setting to dehumidify the air. 1(Defrost): This setting operates the defroster. Most of the air comes out near the windshield, with some going to the ﬂoor outlets and front side windows. The air conditioning compressor may operate in this setting to dehumidify the air. The defog setting is useful for cold weather with a large number of passengers or very humid conditions to help keep the windshield clear. Use defrost to remove fog or ice from the windshield quickly in extremely cold conditions. The temperature knob should be in the red area and the fan control toward high. Do not drive the vehicle until all the windows are clear. 3-19 Rear Window Defogger Some vehicles may have a rear window defogger. < R. DEF (Rear Defrost): Press this button to turn the rear window defogger on or off. Be sure to clear as much snow from the window as possible. The rear window defogger uses a warming grid to remove fog or frost from the rear window and will only work when the ignition is RUN. The rear window defogger will turn off several minutes after the button is pressed. If turned on again, the defogger will run for several more minutes before turning off. The defogger can also be turned off by pressing the button again or by turning off the engine. Notice: Using a razor blade or sharp object to clear the inside rear window may damage the rear window defogger. Repairs would not be covered by your warranty. Do not clear the inside of the rear window with sharp objects. Outlet Adjustment Use the outlets located near the center and on the sides of the instrument panel to change the direction of airﬂow. Operation Tips (cid:127) Clear away any ice, snow or leaves from the air inlets at the base of the windshield that may block the ﬂow of air into your vehicle. (cid:127) Use of non-GM approved hood deﬂectors may adversely affect the performance of the system. (cid:127) Keep the path under the front seats clear of objects to help circulate the air inside of your vehicle more effectively. 3-20 Rear Heating System Your vehicle may have a rear heating system that allows you to adjust the amount of air ﬂowing into the rear of the vehicle, from the front-seating area. This feature works with the main climate-control system in your vehicle. REAR HEAT: The thumbwheel for this system is located to the right of the audio system. 9 (Fan): Turn the thumbwheel up or down to increase or decrease the amount of heated air sent to the rear-seating area. HI: Turn the thumbwheel to this position to supply the most amount of heat to the rear-seating area. LO: Turn the thumbwheel to this position to supply the least amount of heat to the rear-seating area. OFF: Turn the thumbwheel to this position to turn the rear heating system off. 3-21 Rear Air Conditioning and Heating System Your vehicle may have a rear heating and air-conditioning system. This system regulates the temperature, the fan speed and the air delivery for the rear-seat passengers only. It also works with the main climate-control system in your vehicle. Front Climate-Control Panel Use this control panel when you would like to maintain a separate temperature setting. Adjust the direction of the airﬂow or adjust the fan speed for the rear-seat passenger(s). 3-22 Rear Climate-Control Panel If your vehicle has a 135 inch (343 cm) wheelbase, a rear control panel for this system is located in the second row behind the driver in the rear of your vehicle. A rear-seat passenger can use this control panel to personally adjust the temperature, the direction of the airﬂow and the fan speed for the rear-seating area. The fan knob located on the front climate control panel must be turned to REAR CNTL to allow a rear-seat passenger to use the control panel in the rear-seating area. Performing this action disables the front control panel. To return control to this panel, move the fan knob out of REAR CNTL. Turn the center knob clockwise or counterclockwise to change the direction of the airﬂow in the rear-seating area. To change the current mode, select one of the following: D (Vent): Use this mode to direct air to the upper outlets, with a little air directed to the ﬂoor outlets. 2(Floor): Use this mode to direct most of the air to the ﬂoor outlets. 9 (Fan): Turn the left knob clockwise or counterclockwise to HIGH, MED (Medium) or LOW to increase or decrease the fan speed in the rear-seating area. Turn the knob to OFF to turn off the fan. Temperature Control: To increase or decrease the temperature for the rear of the vehicle, turn the right knob located on the climate-control panel. The air-conditioning system on the main climate-control panel must be turned on to direct cooled air to the rear of the vehicle. If it is not on, then the temperature in the rear of the vehicle will remain at cabin temperature. Be sure to keep the area under the front seats clear of any objects so that the air inside of your vehicle can circulate effectively. For information on how to use the main climate-control system, see Climate Control System on page 3-18. For information on ventilation, see Outlet Adjustment on page 3-20. Warning Lights, Gages, and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to your warning lights and gages could also save you or others from injury. Warning lights come on when there may be or is a problem with one of your vehicle’s functions. As you will see in the details on the next few pages, some warning lights come on brieﬂy when you start the engine just to let you know they’re working. If you are familiar with this section, you should not be alarmed when this happens. Gages can indicate when there may be or is a problem with one of your vehicle’s functions. Often gages and warning lights work together to let you know when there’s a problem with your vehicle. When one of the warning lights comes on and stays on when you are driving, or when one of the gages shows there may be a problem, check the section that tells you what to do about it. Please follow this manual’s advice. Waiting to do repairs can be costly – and even dangerous. So please get to know your warning lights and gages. They’re a big help. 3-23 Instrument Panel Cluster United States version shown, Canada similar The instrument panel cluster is designed to let you know at a glance how the vehicle is running. You will know how fast you are going, how much fuel you are using, and many other things you will need to know to drive safely and economically. 3-24 Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). Your vehicle has a tamper resistant odometer. The digital odometer will read 999,999 if someone tries to turn it back. You may wonder what happens if your vehicle needs a new odometer installed. If the new one can be set to the mileage total of the old odometer, then it must be. But if it can’t, then it’s set at zero and a label must be put on the driver’s door to show the old mileage reading when the new odometer was installed. Trip Odometer The trip odometer can tell you how far your vehicle has been driven since you last set the trip odometer to zero. Press the reset button, located on the instrument panel cluster next to the trip odometer display, to toggle between the trip odometer and the regular odometer. Holding the reset button for approximately one second while the trip odometer is displayed will reset it. To display the odometer reading with the ignition off, press the reset button. Engine Speed Limiter Your vehicle may have this feature. This system automatically controls top vehicle speed. The system controller receives a signal from the vehicle speed sensor and reduces power when the vehicle speed reaches the maximum 65 mph (105 km/h) governed speed. Safety Belt Reminder Light When the key is turned to RUN or START, a chime will be provided for several seconds to remind people to buckle their safety belts. The driver safety belt light will also be provided and stay on for several seconds, then it will ﬂash for several more. You should buckle your seat belt. This chime and light will be repeated if the driver remains unbuckled and the vehicle is in motion. If the driver’s belt is buckled, neither the chime nor the light will be provided. 3-25 Airbag Readiness Light There is an airbag readiness light on the instrument panel, which shows the airbag symbol. The system checks the airbag’s electrical system for malfunctions. The light tells you if there is an electrical problem. The system check includes the airbag sensor, the airbag modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 1-61. This light will come on when you start your vehicle, and it will ﬂash for a few seconds. Then the light should go out. This means the system is ready. If the airbag readiness light stays on after you start the vehicle or comes on when you are driving, your airbag system may not work properly. Have your vehicle serviced right away. {CAUTION: If the airbag readiness light stays on after you start your vehicle, it means the airbag system may not be working properly. The airbags in your vehicle may not inﬂate in a crash, or they could even inﬂate without a crash. To help avoid injury to yourself or others, have your vehicle serviced right away if the airbag readiness light stays on after you start your vehicle. The airbag readiness light should ﬂash for a few seconds when you turn the ignition key to RUN. If the light doesn’t come on then, have it ﬁxed so it will be ready to warn you if there is a problem. 3-26 Airbag Off Light If your vehicle is equipped with an airbag off switch, when you turn the right front passenger’s airbag off, the airbag off light will come on and stay on to remind you that the airbag has been turned off. This light will go off when you turn the airbag back on again. See Airbag Off Switch on page 1-69 for more on this, including important safety information. {CAUTION: If the right front passenger’s airbag is turned off for a person who is not in a risk group identiﬁed by the national government, that person will not have the extra protection of an airbag. In a crash, the airbag will not be able to inﬂate and help protect the person sitting there. Do not turn off the passenger’s airbag unless the person sitting there is in a risk group identiﬁed by the national government. See Airbag Off Switch on page 1-69 for more on this, including important safety information. United States Canada 3-27 {CAUTION: If the airbag readiness light ever comes on when you have turned off the airbag, it means that something may be wrong with the airbag system. The right front passenger’s airbag could inﬂate even though the switch is off. If this ever happens, do not let anyone whom the national government has identiﬁed as a member of a passenger airbag risk group sit in the right front passenger’s position (for example, do not secure a rear-facing child restraint in your vehicle) until you have your vehicle serviced. See Airbag Off Switch on page 1-69. Charging System Light This light should come on brieﬂy when you turn on the ignition, before starting the engine, as a check to show you it is working. After the engine starts, the light should go out. If it stays on or comes on while you are driving, you may have a problem with your charging system. It could indicate a problem with the generator drive belt, or some other charging system problem. Have it checked right away. Driving while this light is on could drain your battery. If you must drive a short distance with this light on, it helps to turn off all your accessories, such as the radio and air conditioner. 3-28 Voltmeter Gage When your engine is not running, but the ignition is on (in the RUN position), this gage shows your battery’s state of charge in DC volts. When the engine is running, the gage shows the condition of the charging system. Readings between the low and high warning zones indicate the normal operating range. Readings in the low warning zone may occur when a large number of electrical accessories are operating in the vehicle and the engine is left at an idle for an extended period. This condition is normal since the charging system is not able to provide full power at engine idle. As engine speeds are increased, this condition should correct itself as higher engine speeds allow the charging system to create maximum power. You can only drive for a short time with the reading in either warning zone. If you must drive, turn off all unnecessary accessories. Readings in either warning zone indicate a possible problem in the electrical system. Have the vehicle serviced as soon as possible. Brake System Warning Light With the ignition on, the brake system warning light will come on when you set your parking brake. The light will stay on if your parking brake doesn’t release fully. If it stays on after your parking brake is fully released, it means you have a brake problem. Your vehicle’s hydraulic brake system is divided into two parts. If one part isn’t working, the other part can still work and stop you. For good braking, though, you need both parts working well. If the warning light comes on, there could be a brake problem. Have your brake system inspected right away. 3-29 {CAUTION: Your brake system may not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to an accident. If the light is still on after you have pulled off the road and stopped carefully, have the vehicle towed for service. United States Canada This light should come on brieﬂy when you turn the ignition key to RUN. If it doesn’t come on then, have it ﬁxed so it will be ready to warn you if there’s a problem. If the light comes on while you are driving, pull off the road and stop carefully. You may notice that the pedal is harder to push. Or, the pedal may go closer to the ﬂoor. It may take longer to stop. If the light is still on, have the vehicle towed for service. See Towing Your Vehicle on page 4-36. 3-30 StabiliTrak Not Ready Light If your vehicle has the StabiliTrak® system, this light will come on according to the description table for the StabiliTrak® system. For more information, see StabiliTrak® System on page 4-9. You will hear three chimes if the light turns on and one chime if the light turns off. Anti-Lock Brake System Warning Light With the anti-lock brake system, this light will come on when you start your engine and may stay on for several seconds. That’s normal. If the light stays on, or comes on when you’re driving, your vehicle needs service. If the regular brake system warning light isn’t on, you still have brakes, but you don’t have anti-lock brakes. If the regular brake system warning light is also on, you don’t have anti-lock brakes and there’s a problem with your regular brakes. See Brake System Warning Light on page 3-29 for more information. The anti-lock brake system warning light should come on brieﬂy when you turn the ignition key to RUN. If the light doesn’t come on then, have it ﬁxed so it will be ready to warn you if there is a problem. 3-31 StabiliTrak Indicator Light Engine Coolant Temperature Gage If you have the StabiliTrak system, this light will be on or ﬂashing, according to the description table for the StabiliTrak® system. For more information, see StabiliTrak® System on page 4-9. You will hear three chimes if the light turns on and one chime if the light turns off. If this light remains on steady, your vehicle needs to be taken in for service. 3-32 United States Canada This gage shows the engine coolant temperature. If the gage pointer moves into the red area your engine is too hot! It means that your engine coolant has overheated. If you have been operating your vehicle under normal operating conditions, you should pull off the road, stop your vehicle, and turn off the engine as soon as possible. See Engine Overheating on page 5-25. Malfunction Indicator Lamp Check Engine Light Your vehicle is equipped with a computer which monitors operation of the fuel, ignition, and emission control systems. This system is called OBD II (On-Board Diagnostics-Second Generation) and is intended to assure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment. The Check Engine light comes on to indicate that there is a problem and service is required. Malfunctions often will be indicated by the system before any problem is apparent. This may prevent more serious damage to your vehicle. This system is also designed to assist your service technician in correctly diagnosing any malfunction. If you keep driving your vehicle with this Notice: light on, after awhile, your emission controls may not work as well, your fuel economy may not be as good, and your engine may not run as smoothly. This could lead to costly repairs that may not be covered by your warranty. Notice: Modiﬁcations made to the engine, transmission, exhaust, intake, or fuel system of your vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect your vehicle’s emission controls and may cause this light to come on. Modiﬁcations to these systems could lead to costly repairs not covered by your warranty. This may also result in a failure to pass a required Emission Inspection/Maintenance test. This light should come on, as a check to show you it is working, when the ignition is on and the engine is not running. If the light does not come on, have it repaired. This light will also come on during a malfunction in one of two ways: Light Flashing — A misﬁre condition has been detected. A misﬁre increases vehicle emissions and may damage the emission control system on your vehicle. Diagnosis and service may be required. Light On Steady — An emission control system malfunction has been detected on your vehicle. Diagnosis and service may be required. 3-33 (cid:127) (cid:127) If the Light Is Flashing The following may prevent more serious damage to your vehicle: (cid:127) Reducing vehicle speed (cid:127) Avoiding hard accelerations (cid:127) Avoiding steep uphill grades If you are towing a trailer, reduce the amount of cargo being hauled as soon as it is possible If the light stops ﬂashing and remains on steady, see “If the Light Is On Steady” following. If the light continues to ﬂash, when it is safe to do so, stop the vehicle. Find a safe place to park your vehicle. Turn the key off, wait at least 10 seconds and restart the engine. If the light remains on steady, see “If the Light Is On Steady” following. If the light is still ﬂashing, follow the previous steps, and see your dealer for service as soon as possible. If the Light Is On Steady You may be able to correct the emission system malfunction by considering the following: Did you recently put fuel into your vehicle? If so, reinstall the fuel cap, making sure to fully install the cap. See Filling Your Tank on page 5-8. The diagnostic system can determine if the fuel cap has 3-34 been left off or improperly installed. A loose or missing fuel cap will allow fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off. Did you just drive through a deep puddle of water? If so, your electrical system may be wet. The condition will usually be corrected when the electrical system dries out. A few driving trips should turn the light off. Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel. See Gasoline Octane on page 5-5. Poor fuel quality will cause your engine not to run as efficiently as designed. You may notice this as stalling after start-up, stalling when you put the vehicle into gear, misﬁring, hesitation on acceleration, or stumbling on acceleration. (These conditions may go away once the engine is warmed up.) This will be detected by the system and cause the light to turn on. If you experience one or more of these conditions, change the fuel brand you use. It will require at least one full tank of the proper fuel to turn the light off. If none of the above steps have made the light turn off, your dealer can check the vehicle. Your dealer has the proper test equipment and diagnostic tools to ﬁx any mechanical or electrical problems that may have developed. (cid:127) Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or may begin programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration. Here are some things you need to know to help your vehicle pass an inspection: Your vehicle will not pass this inspection if the Check Engine light is on or not working properly. Your vehicle will not pass this inspection if the OBD (on-board diagnostic) system determines that critical emission control systems have not been completely diagnosed by the system. The vehicle would be considered not ready for inspection. This can happen if you have recently replaced your battery or if your battery has run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This may take several days of routine driving. If you have done this and your vehicle still does not pass the inspection for lack of OBD system readiness, your GM dealer can prepare the vehicle for inspection. Oil Pressure Gage United States Canada The oil pressure gage shows the engine oil pressure in psi (pounds per square inch) when the engine is running. Canadian vehicles indicate pressure in kPa (kilopascals). Oil pressure may vary with engine speed, outside temperature and oil viscosity, but readings above the low pressure zone indicate the normal operating range. 3-35 A reading in the low pressure zone may be caused by a dangerously low oil level or other problem causing low oil pressure. Check your oil as soon as possible.

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2005 GMC Savana Owners Manual