2016 GMC Canyon Owners Manual

4. Press the MENU knob to

select.

Press o BACK to go to the last menu and save the changes. Setting the Time and Date with Touchscreen Controls To set the time: 1. Touch SETTINGS on the Home

Page, then touch Time and Date.

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

104

Instruments and Controls

2. Touch Set Time, then touch « or ª to increase or decrease hours, minutes, and AM or PM. Touch 12–24 Hr for 12 or 24 hour clock.

3. Touch S to go back to the

previous menu.

Auto Set requires an active connection to OnStar. If auto timing is set, the time displayed on the clock may not update immediately when driving into a new time zone. To set the date: 1. Touch SETTINGS on the Home

Page, then touch Time and Date.

2. Touch Set Date, then touch « or ª to increase or decrease month, day, or year.

3. Touch S to go back to the

previous menu.

To set the clock display:

1. Touch SETTINGS on the Home

Page, then touch Time and Date.

2. Touch Clock Display, then touch Off or On to turn the clock display off or on.

3. Touch S to go back to the

previous menu.

Power Outlets Accessory power outlets can be used to plug in electrical equipment, such as a cell phone, MP3
player, etc. The vehicle may have accessory power outlets: . On the center stack below the

climate control system, if equipped.

. On the center floor console,

if equipped.

. On the rear of the center storage

console.

Lift the cover to access and replace when not in use.

{ Warning

Power is always supplied to the outlets. Do not leave electrical equipment plugged in when the vehicle is not in use because the vehicle could catch fire and cause injury or death.

Caution

Leaving electrical equipment plugged in for an extended period of time while the vehicle is off will drain the battery. Always unplug electrical equipment when not in use and do not plug in equipment that exceeds the maximum 15 amp rating.

Certain power accessory plugs may not be compatible with the accessory power outlet and could overload vehicle or adapter fuses. If a problem is experienced, see your dealer.

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

Instruments and Controls

105

When adding electrical equipment, be sure to follow the proper installation instructions included with the equipment. See Add-On Electrical Equipment 0 254

ii

Caution

Hanging heavy equipment from the power outlet can cause damage not covered by the vehicle warranty. The power outlets are designed for accessory power plugs only, such as cell phone charge cords.

Warning Lights, Gauges, and Indicators Warning lights and gauges can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to the warning lights and gauges could prevent injury. Some warning lights come on briefly when the engine is started to indicate they are working. When one of the warning lights comes on and stays on while driving, or when one of the gauges shows there may be a problem, check the section that explains what to do. Waiting to do repairs can be costly and even dangerous.

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

106

Instruments and Controls

Instrument Cluster (Base Level)

English Shown, Metric Similar

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

If the vehicle has a diesel engine, see the Duramax diesel supplement for more information.

Instruments and Controls

107

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

108

Instruments and Controls

Instrument Cluster (Uplevel)

English Shown, Metric Similar

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

If the vehicle has a diesel engine, see the Duramax diesel supplement for more information. Cluster Menu There is an interactive display area in the center of the instrument cluster.

Use the right steering wheel control to open and scroll through the different items and displays. Press o to access the cluster applications. Use w or x to scroll through the list of available applications. Not all applications will be available on all vehicles.

Instruments and Controls

109

Info app. This is where you can view the selected Driver Information Center (DIC) displays. See Driver Information Center (DIC) (Base Level) 0 122
or Driver Information Center (DIC) (Uplevel) 0 125

ii

ii

. Audio . Phone . Navigation . Settings

Audio In the main view of the Audio app, press w or x to scroll through radio stations or move to the next/ previous track of a CD/USB/ Bluetooth device that is connected to the vehicle. Press V to select the Audio app, then press p to enter the Audio menu. In the Audio menu browse for music, select from the favorites, or change the audio source.

Phone

Press V to select the Phone app, then press p to enter the Phone menu. In the Phone menu, if there is no active phone call, view recent calls, scroll through contacts, or select from the favorites. If there is an active call, mute or unmute the phone or switch to handset or handsfree operation.

Navigation

Press V to select the Navigation app, then press p to enter the Navigation menu. If there is no active route, you can resume the last route and turn the voice prompts on/off. If there is an active route, press V to cancel route guidance or turn the voice prompts on/off.

Settings

Press V to select the Settings app. Use w or x to scroll through the items in the Settings menu.

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

110

Instruments and Controls

ii

or Driver

Units : Press p while Units is displayed to enter the Units menu. Choose U.S. or metric units by pressing V while the desired item is highlighted. Info Pages : Press p while Info Pages is displayed to enter the Info Pages menu and select the items to be displayed in the Info app. See Driver Information Center (DIC) (Base Level) 0 122
Information Center (DIC) (Uplevel) 0 125
Speed Warning : The Speed Warning display allows the driver to set a speed that they do not want to exceed. To set the Speed Warning, press p when Speed Warning is displayed. Press w or x to adjust the value. Press V to set the speed. Once the speed is set, this feature can be turned off by pressing V while viewing this page. If the selected speed limit is exceeded, a pop-up warning is displayed with a chime.

ii

Fuel Gauge

Speedometer The speedometer shows the vehicle's speed in either kilometers per hour (km/h) or miles per hour (mph).

Odometer The odometer shows how far the vehicle has been driven, in either kilometers or miles.

Metric

Trip Odometer The trip odometer shows how far the vehicle has been driven since the trip odometer was last reset. The trip odometer is accessed and reset through the Driver Information Center (DIC). See Driver Information Center (DIC) (Base Level) 0 122
Center (DIC) (Uplevel) 0 125

or Driver Information

ii

ii

Tachometer The tachometer displays the engine speed in revolutions per minute (rpm).

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

Instruments and Controls

111

. At the service station, the fuel

pump shuts off before the gauge reads full. It takes a little more or less fuel to fill up than the gauge indicated. For example, the gauge indicated the tank was half full, but it actually took a little more or less than half the tank's capacity to fill the tank. . The gauge moves a little while

turning a corner or speeding up. . The gauge takes a few seconds

to stabilize after the ignition is turned on, and goes back to empty when the ignition is turned off.

Engine Coolant Temperature Gauge

Metric

English

When the ignition is on, the fuel gauge indicates about how much fuel is left in the tank. An arrow on the fuel gauge indicates the side of the vehicle the fuel door is on. When the indicator nears empty, the low fuel light comes on. There is a small amount of fuel left, but the fuel tank should be filled soon. Here are four things that some owners ask about. None of these show a problem with the fuel gauge:

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

112

Instruments and Controls

Safety Belt Reminders

Driver Safety Belt Reminder Light There is a driver safety belt reminder light on the instrument cluster.

Passenger Safety Belt Reminder Light There is a passenger safety belt reminder light near the passenger airbag status indicator. See Passenger Sensing System 0 62

ii

English

This gauge shows the engine coolant temperature. If the pointer moves toward the warning area at the high end of the gauge, the engine is too hot. This reading indicates the same thing as the warning light. It means that the engine coolant has overheated. If the vehicle has been operating under normal driving conditions, pull off the road, stop the vehicle, and turn off the engine as soon as possible. See Engine Overheating 0 271

ii

When the vehicle is started, this light flashes and a chime may come on to remind the driver to fasten their safety belt. Then the light stays on solid until the belt is buckled. This cycle may continue several times if the driver remains or becomes unbuckled while the vehicle is moving. If the driver safety belt is buckled, neither the light nor the chime comes on.

When the vehicle is started, this light flashes and a chime may come on to remind passengers to fasten their safety belt. Then the light stays on solid until the belt is buckled. This cycle continues several times if the passenger remains or becomes unbuckled while the vehicle is moving. If the passenger safety belt is buckled, neither the chime nor the light comes on. The front passenger safety belt reminder light and chime may turn on if an object is put on the seat such as a briefcase, handbag,

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

Instruments and Controls

113

grocery bag, laptop, or other electronic device. To turn off the reminder light and/or chime, remove the object from the seat or buckle the safety belt.

Airbag Readiness Light This light shows if there is an electrical problem with the airbag system. The system check includes the airbag sensor(s), the passenger sensing system, the pretensioners, the airbag modules, the wiring, and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System 0 56

ii

{ Warning

If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash. To help avoid injury, have the vehicle serviced right away.

If there is a problem with the airbag system, a Driver Information Center (DIC) message may also come on. See Airbag System Messages 0 133

ii

The airbag readiness light comes on for several seconds when the vehicle is started. If the light does not come on then, have it fixed immediately.

Passenger Airbag Status Indicator The vehicle has a passenger sensing system. See Passenger Sensing System 0 62
safety information. The overhead console has a passenger airbag status indicator.

for important

ii

United States

Canada

When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check. Then, after several more seconds, the status indicator will light either ON or OFF, or either the on or off symbol, to let you know the status of the front outboard passenger frontal airbag.

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

114

Instruments and Controls

If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the front outboard passenger frontal airbag is allowed to inflate. If the word OFF or the off symbol is lit on the airbag status indicator, it means that the passenger sensing system has turned off the front outboard passenger frontal airbag. If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service.

{ Warning

If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light 0 113
including important safety information.

for more information,

ii

Charging System Light

The charging system light comes on briefly when the ignition is turned on, but the engine is not running, as a check to show the light is working. It should go out when the engine is started. If the light stays on or comes on while driving, there may be a problem with the electrical charging system. Have it checked by your dealer. Driving while this light is on could drain the battery. When this light comes on, the Driver Information Center (DIC) also displays a message. See Battery Voltage and Charging Messages 0 128
If a short distance must be driven with the light on, be sure to turn off all accessories, such as the radio and air conditioner.

ii

Malfunction Indicator Lamp (Check Engine Light) This light is part of the vehicle’s emission control on-board diagnostic system. If this light is on while the engine is running, a malfunction has been detected and the vehicle may require service. The light should come on to show that it is working when the ignition is in ON/RUN and the engine is not running. See Ignition Positions 0 211

ii

Malfunctions are often indicated by the system before any problem is noticeable. Being aware of the light and seeking service promptly when it comes on may prevent damage.

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

Instruments and Controls

115

Caution

If the vehicle is driven continually with this light on, the emission control system may not work as well, the fuel economy may be lower, and the vehicle may not run smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty.

Caution

Modifications to the engine, transmission, exhaust, intake, or fuel system, or the use of replacement tires that do not meet the original tire specifications, can cause this light to come on. This could lead to costly repairs not covered by the vehicle warranty. This could also affect the vehicle’s ability to pass an Emissions Inspection/ Maintenance test. See Accessories and Modifications 0 257

ii

If the light is flashing : A malfunction has been detected that could damage the emission control system and increase vehicle emissions. Diagnosis and service may be required. To help prevent damage, reduce vehicle speed and avoid hard accelerations and uphill grades. If towing a trailer, reduce the amount of cargo being hauled as soon as possible. If the light continues to flash, find a safe place to park. Turn the vehicle off and wait at least 10 seconds before restarting the engine. If the light is still flashing, follow the previous guidelines and see your dealer for service as soon as possible. If the light is on steady : A malfunction has been detected. Diagnosis and service may be required. Check the following: . A loose or missing fuel cap may cause the light to come on. See Filling the Tank 0 243

. A few

ii

driving trips with the cap properly installed may turn the light off.

. Poor fuel quality can cause

inefficient engine operation and poor driveability, which may go away once the engine is warmed up. If this occurs, change the fuel brand. It may require at least one full tank of the proper fuel to turn the light off. See Fuel 0 241

ii

If the light remains on, see your dealer. Emissions Inspection and Maintenance Programs If the vehicle requires an Emissions Inspection/Maintenance test, the test equipment will likely connect to the vehicle's Data Link Connector (DLC).

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

116

Instruments and Controls

The DLC is under the instrument panel to the left of the steering wheel. Connecting devices that are not used to perform an Emissions Inspection/Maintenance test or to service the vehicle may affect vehicle operation See Add-On Electrical Equipment 0 254
your dealer if assistance is needed. The vehicle may not pass inspection if: . The light is on when the engine

. See

ii

is running.

. The light does not come on

when the ignition is in ON/RUN while the engine is off.

. Critical emission control systems

have not been completely diagnosed. If this happens, the vehicle would not be ready for inspection and might require several days of routine driving before the system is ready for inspection. This can happen if the 12-volt battery has recently been replaced or run down, or if the vehicle has been recently serviced.

See your dealer if the vehicle will not pass or cannot be made ready for the test.

Brake System Warning Light The vehicle brake system consists of two hydraulic circuits. If one circuit is not working, the remaining circuit can still work to stop the vehicle. For normal braking performance, both circuits need to be working. If the warning light comes on, there is a brake problem. Have the brake system inspected right away.

When the ignition is on, the brake system warning light also comes on when the parking brake is set. The light stays on if the parking brake does not fully release. If it stays on after the parking brake is fully released, it means the vehicle has a brake problem. If the light comes on while driving, pull off the road and stop carefully. The pedal might be harder to push, or the pedal can go closer to the floor. It may take longer to stop. If the light is still on, have the vehicle towed for service. See Towing the Vehicle 0 326
{ Warning

ii

Metric

English

This light should come on briefly when the engine is started. If it does not come on then, have it fixed so it will be ready to warn you if there is a problem.

The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service.

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

Instruments and Controls

117

Tow/Haul Mode Light

Antilock Brake System (ABS) Warning Light

If both the ABS and the brake system warning light are on, the vehicle's antilock brakes are not functioning and there is a problem with the regular brakes. See your dealer for service. See Brake System Warning Light 0 116
0 129

and Brake System Messages

ii

This light comes on briefly when the engine is started. If the light does not come on, have it fixed so it will be ready to warn if there is a problem. If the light comes on while driving, stop as soon as it is safely possible and turn off the vehicle. Then start the engine again to reset the system. If the ABS light stays on, or comes on again while driving, the vehicle needs service. A chime may also sound when the light comes on steady. If the ABS light is the only light on, the vehicle has regular brakes, but the antilock brakes are not functioning.

ii

Up-Shift Light (Manual Transmission)

This light comes on when an up-shift is recommended for best fuel economy. The number displayed with the arrow indicates the recommended gear.

For vehicles with the Tow/Haul Mode feature, this light comes on when the Tow/Haul Mode has been activated. See Tow/Haul Mode 0 223

ii

Hill Descent Control Light

If equipped, the Hill Descent Control light comes on when the system is ready for use. When the light flashes, the system is active. See Hill Descent Control (HDC) 0 233

ii

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

118

Instruments and Controls

Lane Departure Warning (LDW) Light

Vehicle Ahead Indicator

If equipped, this indicator will display green when a vehicle is detected ahead and amber when you are following a vehicle ahead much too closely. See Forward Collision Alert (FCA) System 0 238

ii

Traction Off Light

If equipped, this light comes on briefly while starting the vehicle. If it does not come on, have the vehicle serviced. This light is green if LDW is on and ready to operate. This light changes to amber and flashes to indicate that the lane marking has been crossed without using a turn signal in that direction. See Lane Departure Warning (LDW) 0 240

ii

dealer. If the system is working normally, the indicator light then turns off. The traction off light comes on when the Traction Control System (TCS) has been turned off by pressing and releasing the TCS/StabiliTrak button. This light and the StabiliTrak OFF light come on when StabiliTrak is turned off. If the TCS is off, wheel spin is not limited. Adjust driving accordingly. See Traction Control/Electronic Stability Control 0 231

ii

StabiliTrak® OFF Light

This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your

This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer.

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

Instruments and Controls

119

This light comes on when the StabiliTrak system is turned off. If StabiliTrak is off, the Traction Control System (TCS) is also off. If StabiliTrak and TCS are off, the system does not assist in controlling the vehicle. Turn on the TCS and the StabiliTrak systems, and the warning light turns off. See Traction Control/Electronic Stability Control 0 231

ii

Traction Control System (TCS)/StabiliTrak® Light

If the light is on and not flashing, the TCS and potentially the StabiliTrak system have been disabled. A DIC message may display. Check the DIC messages to determine which feature(s) is no longer functioning and whether the vehicle requires service. If the light is on and flashing, the TCS and/or the StabiliTrak system is actively working. See Traction Control/Electronic Stability Control 0 231

ii

Tire Pressure Light

This light comes on briefly when the engine is started. If the light does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off.

For vehicles with the Tire Pressure Monitor System (TPMS), this light comes on briefly when the engine is started. It provides information about tire pressures and the TPMS.

When the Light Is On Steady This indicates that one or more of the tires are significantly underinflated. A Driver Information Center (DIC) tire pressure message may also display. See Tire Messages 0 133
Stop as soon as possible, and inflate the tires to the pressure value shown on the Tire and Loading Information label. See Tire Pressure 0 299

ii

ii

When the Light Flashes First and Then Is On Steady If the light flashes for about a minute and then stays on, there may be a problem with the TPMS. If the problem is not corrected, the light will come on at every ignition cycle. See Tire Pressure Monitor Operation 0 301

ii

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

120

Instruments and Controls

Engine Oil Pressure Light

Caution

Lack of proper engine oil maintenance can damage the engine. Driving with the engine oil low can also damage the engine. The repairs would not be covered by the vehicle warranty. Check the oil level as soon as possible. Add oil if required, but if the oil level is within the operating range and the oil pressure is still low, have the vehicle serviced. Always follow the maintenance schedule for changing engine oil.

If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle could be low on oil and might have some other system problem. See your dealer.

Low Fuel Warning Light (Base Level)

The low fuel warning light comes on and a chime sounds when the vehicle is low on fuel. The light turns off when fuel is added to the fuel tank.

Low Fuel Warning Light (Uplevel)

This light is near the fuel gauge and comes on briefly when the ignition is turned on as a check to show it is working. It also comes on when the fuel tank is low on fuel. The light turns off when fuel is added. If it does not, have the vehicle serviced.

English Shown

This light comes on for a few seconds when the ignition is turned on as a check to indicate it is working. If it does not come on, have it fixed.

This light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer.

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

Security Light

The security light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off. If the light stays on and the engine does not start, there could be a problem with the theft-deterrent system. See Immobilizer Operation 0 35

ii

High-Beam On Light

Instruments and Controls

121

This light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer 0 143

ii

Front Fog Lamp Light

This light comes on when the exterior lamps are in use. See Exterior Lamp Controls 0 142

ii

Cruise Control Light

The fog lamp light comes on when the fog lamps are in use. The light goes out when the fog lamps are turned off. See Fog Lamps 0 145

for more information.

ii

Lamps On Reminder

The cruise control light is white when the cruise control is on and ready, and turns green when the cruise control is set and active. The light goes out when the cruise control is turned off. See Cruise Control 0 234

ii

Door Ajar Light (Uplevel Cluster)

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

122

Instruments and Controls

This light comes on when a door is open or not securely latched. Before driving, check that all doors are properly closed.

Information Displays

2. w x : Use the band to scroll

Driver Information Center (DIC) (Base Level) The DIC displays information about your vehicle. It also displays warning messages if a system problem is detected. See Vehicle . All messages Messages 0 128
appear in the DIC display in the center of the instrument cluster. DIC Operation and Displays The DIC has different displays which can be accessed by using the DIC buttons on the turn signal lever.

ii

DIC Buttons

1. SET/CLR: Press to set,

or press and hold to clear, the menu item displayed.

through the items in each menu.

3. MENU: Press to display the Trip/Fuel Menu, the Vehicle Information Menu, and the ECO Menu. This button is also used to return to or exit the last screen displayed on the DIC. If the vehicle has a diesel engine, see the Duramax diesel supplement for additional DIC pages. Trip/Fuel Menu (TRIP) Items Press MENU on the turn signal lever until the TRIP menu displays. Use w x to scroll through the menu items. Not all items are available on every vehicle. The following is a list of all possible menu items: Digital Speed : Displays how fast the vehicle is moving in either kilometers per hour (km/h) or miles per hour (mph). The speedometer cannot be reset.

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

Instruments and Controls

123

Trip 1 or Trip 2, Average Fuel Economy : Displays the current distance traveled, in either kilometers (km) or miles (mi), from the last reset for the trip odometer. The trip odometer can be reset to zero by pressing and holding the SET/CLR button while the trip odometer display is showing. Also displays the approximate average liters per 100 kilometers (L/ 100 km) or miles per gallon (mpg). This number is based on the number of L/100 km (mpg) recorded since the last time this menu item was reset. This number reflects only the approximate average fuel economy that the vehicle has right now, and will change as driving conditions change. Reset the average consumption by pressing SET/CLR when it is displayed. Fuel Range : Displays the approximate distance the vehicle can be driven without refueling. The fuel range estimate is based on an average of the vehicle's fuel economy over recent driving history

and the amount of fuel remaining in the fuel tank. Fuel range cannot be reset. Average Vehicle Speed : Displays the average vehicle speed of the vehicle in kilometers per hour (km/h) or miles per hour (mph). This average is based on the various vehicle speeds recorded since the last reset. Reset the average speed by pressing SET/CLR when it is displayed. Timer : To start the timer, press SET/CLR while Timer is displayed. The display will show the amount of time that has passed since the timer was last reset, not including time the ignition is off. Time will continue to be counted as long as the ignition is on, even if another display is being shown on the DIC. The timer will record up to 99 hours, 59 minutes, and 59 seconds (99:59:59) after which the display will return to zero. To stop the timer, press SET/CLR briefly while Timer is displayed. To reset the timer to zero, press and hold SET/CLR.

ii

Navigation : Used for the OnStar Turn-by-Turn guidance. See OnStar Overview 0 371
Blank Display : Displays no information. Vehicle Information Menu (VEHICLE) Items Press MENU on the turn signal lever until the VEHICLE menu is displayed. Use w x to scroll through the menu items. Not all items are available on every vehicle. The following is a list of all possible menu items: Remaining Oil Life : Displays an estimate of the oil's remaining useful life. If REMAINING OIL LIFE 99% is displayed, that means 99% of the current oil life remains. When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See Engine Oil Messages 0 130
The oil should be changed as soon as possible. See Engine Oil 0 262
In addition to the engine oil life system monitoring the oil life, additional maintenance is

ii

ii

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

124

Instruments and Controls

ii

ii

recommended in the Maintenance Schedule in this manual. See Maintenance Schedule 0 341
The Oil Life display must be reset after each oil change. Do not reset the Oil Life display accidentally at any time other than when the oil has just been changed. It cannot be reset accurately until the next oil change. To reset the engine oil life system, see Engine Oil Life System 0 264
Oil Pressure : Oil pressure is displayed in either kilopascal (kPa) or in pounds per square inch (psi). Tire Pressure : Displays a vehicle with the approximate pressures of all four tires. Tire pressure is displayed in either kilopascal (kPa) or in pounds per square inch (psi). See Tire Pressure Monitor System 0 300
Operation 0 301
Battery Voltage : Displays the current battery voltage, if equipped. Battery voltage changes are normal while driving. See Charging System . If there is a problem Light 0 114
with the battery charging system,

and Tire Pressure Monitor

ii

ii

ii

ii

the DIC will display a message. See Battery Voltage and Charging Messages 0 128
Engine Hours : Shows the total number of hours the engine has run. Transmission Fluid Temperature : Shows the temperature of the automatic transmission fluid in either degrees Celsius (°C) or degrees Fahrenheit (°F). Trailer Brake (If Equipped) : TRAILER GAIN shows the trailer gain setting. This setting can be adjusted from 0.0 to 10.0 with either a trailer connected or disconnected. OUTPUT shows the power output to the trailer anytime a trailer with electric brakes is connected. Output is displayed as a bar graph. Dashes may appear in the OUTPUT display if a trailer is not connected. Units : Move w x to change between Metric or US when the Unit display is active. Press SET/CLR to confirm the setting. This will change the displays on the DIC to the type of measurements you select.

ECO Drive Assist Menu (ECO) Items This menu is only available on some vehicles. Press MENU on the turn signal lever until the ECO menu is displayed. Use w x to scroll through the menu items. Not all items are available on every vehicle. The following is a list of all possible menu items: Best Average Fuel Economy : The bottom displays the best average fuel economy (AFE) that is achieved for a selected distance. The top displays a running average of fuel economy for the most recently traveled selected distance. The center bar graph displays the instantaneous fuel economy. Quickly press the SET/CLR button to change the settings for the distance options. When viewing best AFE, a several second press and hold of SET/CLR will reset the best value. The best value will show “- - -“ until the selected distance has been traveled.

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

Instruments and Controls

125

The display provides feedback on how current driving behavior in the bar graph affects the running average in the top display and how well recent driving compares to the best that has been achieved.

Driver Information Center (DIC) (Uplevel) The DIC displays are shown in the center of the instrument cluster in the Info app. See Instrument Cluster (Base Level) 0 106
Cluster (Uplevel) 0 108
displays show the status of many vehicle systems. The controls for the DIC are on the right steering wheel control.

or Instrument

. The

ii

ii

DIC Info Page Options The info pages on the DIC can be turned on or off through the Settings menu. 1. Press o to access the cluster

applications.

2. Press w or x to scroll to the

Settings application.

3. Press V to enter the

Settings menu.

4. Scroll to Info Pages and

press p.

5. Press w or x to move

through the list of possible information displays.

6. Press V while an item is

highlighted to select or deselect that item. When an item is selected, a checkmark will appear next to it.

DIC Info Pages The following is the list of all possible DIC info page displays. Some may not be available for your particular vehicle. Some items may

w or x : Press to move up or down in a list. o or p : Press to move between the interactive display zones in the cluster. V (Set/Reset) : Press to open a menu or select a menu item. Press and hold to reset values on certain screens. If the vehicle has a diesel engine, see the Duramax diesel supplement for additional DIC pages.

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

126

Instruments and Controls

not be turned on by default but can be turned on through the Settings app. See “DIC Info Page Options” earlier in this section. Speed : Shows the vehicle speed in either kilometers per hour (km/h) or miles per hour (mph). Trip A or Trip B : Shows the current distance traveled, in either kilometers (km) or miles (mi), since the trip odometer was last reset. This also shows the approximate average liters per 100 kilometers (L/ 100 km) or miles per gallon (mpg). This number is calculated based on the number of L/100 km (mpg) recorded since the last time this menu item was reset. This number reflects only the approximate average fuel economy that the vehicle has right now, and will change as driving conditions change.

Press and hold V while this display is active to reset the trip odometer and the average fuel economy. Trip A and Trip B can also be reset by pressing p and choosing reset.

Fuel Range : Shows the approximate distance the vehicle can be driven without refueling. LOW will be displayed when the vehicle is low on fuel. The fuel range estimate is based on an average of the vehicle's fuel economy over recent driving history and the amount of fuel remaining in the fuel tank. Oil Life : Shows an estimate of the oil's remaining useful life. If REMAINING OIL LIFE 99% is displayed, that means 99% of the current oil life remains. When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See Engine Oil Messages 0 130
The oil should be changed as soon as possible. See Engine Oil 0 262
In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule. See Maintenance Schedule 0 341

ii

ii

ii

ii

The Oil Life display must be reset after each oil change. It will not reset itself. Do not to reset the Oil Life display at any time other than when the oil has just been changed. It cannot be reset accurately until the next oil change. To reset the engine oil life system, press and hold V for several seconds while the Oil Life display is active. See Engine Oil Life System 0 264
Tire Pressure : Shows the approximate pressures of all four tires. Tire pressure is displayed in either kilopascal (kPa) or in pounds per square inch (psi). If the pressure is low, the value for that tire is shown in amber. See Tire Pressure Monitor System 0 300
Pressure Monitor Operation 0 301
Instantaneous Fuel Economy : Displays the current fuel economy in liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number reflects only the approximate fuel economy that the vehicle has right now and changes

and Tire

ii

ii

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

Instruments and Controls

127

frequently as driving conditions change. This display cannot be reset. Average Vehicle Speed : Displays the average vehicle speed of the vehicle in kilometers per hour (km/h) or miles per hour (mph). This average is based on the various vehicle speeds recorded since the last reset. Reset the average speed by pressing SET/CLR when it is displayed. Fuel Economy : The center displays the approximate instantaneous fuel economy as a number and bar graph. Displayed above the bar graph is a running average of fuel economy for the most recently traveled selected distance. Displayed below the bar graph is the best average fuel economy that has been achieved for the selected distance. The selected distance is displayed at the top of the page as “last xxx mi/km.” Press p to select the distance or reset best value. Use w and x to choose the distance and press V.

Press w and x to select “Reset Best Score.” Press V to reset the best average fuel economy. After reset, the best value displays “-,-” until the selected distance has been traveled. The display provides information on how current driving behavior affects the running average and how well recent driving compares to the best that has been achieved for the selected distance. Timer : This display can be used as a timer. To start the timer, press V while this display is active. The display will show the amount of time that has passed since the timer was last reset. To stop the timer, press V briefly while this display is active and the timer is running. To reset the timer to zero, press and hold V while this display is active, or press p and select reset. Speed Limit : Shows sign information, which comes from a roadway database in the onboard navigation, if equipped.

ii

ii

Battery Voltage : Displays the current battery voltage, if equipped. Battery voltage changes are normal while driving. See Charging System . If there is a problem Light 0 114
with the battery charging system, the DIC will display a message. See Battery Voltage and Charging Messages 0 128
Oil Pressure : Oil pressure is displayed in either kilopascal (kPa) or in pounds per square inch (psi). Engine Hours : Shows the total number of hours the engine has run. Transmission Fluid Temperature : Shows the temperature of the automatic transmission fluid in either degrees Celsius (°C) or degrees Fahrenheit (°F). Trailer Brake (If Equipped) : TRAILER GAIN shows the trailer gain setting. This setting can be adjusted from 0.0 to 10.0 with either a trailer connected or disconnected. OUTPUT shows the power output to the trailer anytime a trailer with electric brakes is connected. Output

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

128

Instruments and Controls

is displayed as a bar graph. Dashes may appear in the OUTPUT display if a trailer is not connected. Blank Page : Shows no information.

Vehicle Messages Messages displayed on the DIC indicate the status of the vehicle or some action that may be needed to correct a condition. Multiple messages may display one after the other. The messages that do not require immediate action can be acknowledged and cleared by pressing SET/CLR or V. The messages that require immediate action cannot be cleared until that action is performed. All messages should be taken seriously and clearing the messages does not correct the problem. The following are some of the vehicle messages that may be displayed depending on your vehicle content. If the vehicle has a diesel engine, see the Duramax diesel supplement for additional messages.

Battery Voltage and Charging Messages

BATTERY LOW START VEHICLE When the vehicle’s battery is severely discharged, this message will display and four chimes will sound. Start the vehicle immediately. If the vehicle is not started and the battery continues to discharge, the climate controls, heated seats, and audio systems will shut off and the vehicle may require a jump start. These systems will function again after the vehicle is started. BATTERY SAVER ACTIVE This message displays when the battery voltage drops below expected levels and features are disabled. Turn off all unnecessary accessory features.

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

Instruments and Controls

129

ii

SERVICE BATTERY CHARGING SYSTEM On some vehicles, this message displays if there is a problem with the battery charging system. Under certain conditions, the charging system light may also turn on in the instrument cluster. See Charging . Driving with System Light 0 114
this problem could drain the battery. Turn off all unnecessary accessories. Have the electrical system checked as soon as possible. See your dealer. TRANSPORT MODE ON This message is displayed when the vehicle is in transport mode. Some features can be disabled while in this mode, including Remote Keyless Entry (RKE), remote start, and the vehicle alarm system. Take the vehicle to your dealer for service to turn transport mode off.

Brake System Messages

ii

BRAKE FLUID LOW This message is displayed when the brake fluid level is low; see Brake Fluid 0 275
HILL START ASSIST ACTIVE This message is displayed when the vehicle is stopped on a grade sufficient to activate HSA. HSA holds the braking pressure for a maximum of two seconds to ensure that there is no rolling, which will assist the driver to transition between releasing the brake pedal and accelerating to drive off while on the grade. The brakes will automatically release when the accelerator pedal is applied within the two-second window. See Hill Start Assist (HSA) 0 231
RELEASE PARKING BRAKE This message is displayed as a reminder that the parking brake is on. Release it before you attempt to drive.

ii

SERVICE BRAKE ASSIST This message may be displayed when there is a problem with the brake boost assist system. When this message is displayed, the brake boost assist motor may be heard operating and you might notice pulsation in the brake pedal. This is normal under these conditions. Take the vehicle to your dealer for service.

Compass Messages Dashes may be displayed if the vehicle temporarily loses communication with the Global Positioning System (GPS).

Door Ajar Messages

DOOR OPEN This message displays and a chime may sound if a door is not fully closed. Stop and turn off the vehicle, check the door for obstructions, and close the door again. Check to see if the message still appears on the DIC.

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

130

Instruments and Controls

ii

ENGINE OVERHEATING, IDLE ENGINE This message displays when the engine coolant temperature is too hot. Stop and allow the vehicle to idle until it cools down. See Engine Coolant Temperature Gauge 0 111
When towing, use Tow/Haul Mode to prevent damage to the engine or transmission. See Tow/Haul Mode 0 223
ENGINE OVERHEATED STOP ENGINE This message displays and a chime may sound if the engine cooling system reaches unsafe temperatures for operation. Stop and turn off the vehicle as soon as it is safe to do so to avoid severe damage. This message clears when the engine has cooled to a safe operating temperature.

ii

HOOD OPEN This message displays and a chime may sound if the hood is not fully closed. Stop and turn off the vehicle, check the hood for obstructions, and close the hood again. Check to see if the message still appears on the DIC.

Engine Cooling System Messages

ii

AIR CONDITIONING OFF This message displays when the engine coolant becomes hotter than the normal operating temperature. See Engine Coolant Temperature . To avoid added strain Gauge 0 111
on a hot engine, the air conditioning compressor automatically turns off. When the coolant temperature returns to normal, the air conditioning compressor turns back on. You can continue to drive your vehicle. If this message continues to appear, have the system repaired by your dealer as soon as possible to avoid damage to the engine.

Engine Oil Messages

and

ii

ii

ii

for

CHANGE ENGINE OIL SOON This message displays when the engine oil needs to be changed. When you change the engine oil, be sure to reset the CHANGE ENGINE OIL SOON message. See Engine Oil Life System 0 264
information on how to reset the message. See Engine Oil 0 262
Maintenance Schedule 0 341
ENGINE OIL LOW ADD OIL On some vehicles, this message displays when the engine oil level may be too low. Check the oil level before filling to the recommended level. If the oil is not low and this message remains on, take the vehicle to your dealer for service. See Engine Oil 0 262
ENGINE OIL HOT IDLE ENGINE This message displays when the engine oil becomes hotter than the normal operating temperature. Stop

ii

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

Instruments and Controls

131

ii

and allow the vehicle to idle until it cools down. See Engine Coolant Temperature Gauge 0 111
OIL PRESSURE LOW STOP ENGINE This message displays if low oil pressure levels occur. Stop the vehicle as soon as safely possible and do not operate it until the cause of the low oil pressure has been corrected. Check the oil as soon as possible and have the vehicle serviced by your dealer. See Engine Oil 0 262

ii

Engine Power Messages

ENGINE POWER IS REDUCED This message displays and a chime may sound when the cooling system temperature gets too hot and the engine further enters the engine coolant protection mode. See Engine Overheating 0 271
information. This message also displays when the vehicle's engine power is reduced. Reduced engine power can affect the vehicle's ability to

for more

ii

accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer for service as soon as possible.

Fuel System Messages

ii

and Fuel 0 241

FUEL LEVEL LOW This message displays and a chime may sound if the fuel level is low. Refuel as soon as possible. See Fuel Gauge 0 110
TIGHTEN GAS CAP This message may display along with the malfunction indicator lamp on the instrument cluster if the vehicle's fuel cap is not tightened properly. See Malfunction Indicator Lamp (Check Engine Light) 0 114
Reinstall the fuel cap fully. See Filling the Tank 0 243

. The

ii

ii

ii

diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn this light and message off.

Key and Lock Messages

REPLACE BATTERY IN REMOTE KEY This message displays if a Remote Keyless Entry (RKE) transmitter battery is low. The battery needs to be replaced in the transmitter. See “Battery Replacement” under Remote Keyless Entry (RKE) System Operation 0 28

ii

Lamp Messages

TURN SIGNAL ON This message displays and a chime sounds if a turn signal is left on for 1.2 km (0.75 mi). Move the turn signal lever to the off position.

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

132

Instruments and Controls

Object Detection System Messages

ii

FORWARD COLLISION ALERT OFF If your vehicle has the Forward Collision Alert (FCA) system, this message may display if the FCA system cannot activate due to a temporary condition. See Forward Collision Alert (FCA) System 0 238
FRONT CAMERA BLOCKED, CLEAN WINDSHIELD This message displays when the Lane Departure Warning (LDW) and Forward Collision Alert (FCA) systems are disabled because the camera view is blocked and cannot operate properly. It may also activate during heavy rain or due to road spray. To clean the system, clean the outside of the windshield area in front of the LDW/FCA camera sensor.

LANE DEPARTURE SYSTEM UNAVAILABLE If your vehicle has the Lane Departure Warning (LDW) system, this message may display if the LDW system cannot activate due to a temporary condition. See Lane Departure Warning (LDW) 0 240
more information. SERVICE FRONT CAMERA This message displays when the Lane Departure Warning (LDW) and Forward Collision Alert (FCA) systems are disabled and need service. See your dealer.

for

ii

Ride Control System Messages

SERVICE STABILITRAK If this message displays, it means there may be a problem with the StabiliTrak system. If you see this message, try to reset the system. Stop; turn off the engine for at least 15 seconds; then start the engine again. If this message still comes on, it means there is a problem. You

should see your dealer for service. The vehicle is safe to drive; however, you do not have the benefit of StabiliTrak, so reduce your speed and drive accordingly. SERVICE TRACTION CONTROL This message displays when there is a problem with the Traction Control System (TCS). When this message displays, the system will not limit wheel spin. Adjust your driving accordingly. See your dealer for service. See Traction Control/ Electronic Stability Control 0 231
STABILITRAK INITIALIZING This message may come on if the StabiliTrak system has not fully initialized because of road conditions or the incorrect tire size. When the StabiliTrak system is fully initialized, the message will turn off. See Traction Control/Electronic Stability Control 0 231
message continues to be displayed for multiple ignition cycles and on different road surfaces, see your dealer for service.

. If this

ii

ii

GMC Canyon Owner Manual 2016 - crc - 8/25/15

(GMNA-Localizing-U.S/Canada-9159361)

Instruments and Controls

133

Airbag System Messages

SERVICE AIRBAG This message displays if there is a problem with the airbag system. Take the vehicle to your dealer for service.

Security Messages

SERVICE THEFT DETERRENT