2010 GMC Canyon Owners Manual

Download PDF Manual
pedal pressed in, turn the ignition key to LOCK/OFF, remove the key and release the clutch. If you are parking on a hill, or if the vehicle is pulling a trailer, see Towing a Trailer on page 5-48. Parking Over Things That Burn { WARNING: Things that can burn could touch hot exhaust parts under the vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. 3-33 Engine Exhaust { WARNING: Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. Exposure to CO can cause unconsciousness and even death. Exhaust may enter the vehicle if: • The vehicle idles in areas with poor ventilation (parking garages, tunnels, deep snow that may block underbody airﬂow or tail pipes). • The exhaust smells or sounds strange or different. or damage. • The exhaust system leaks due to corrosion • The vehicle’s exhaust system has been modiﬁed, damaged or improperly repaired. • There are holes or openings in the vehicle body from damage or after-market modiﬁcations that are not completely sealed. WARNING: (Continued) 3-34 WARNING: (Continued) If unusual fumes are detected or if it is suspected that exhaust is coming into the vehicle: • Drive it only with the windows completely down. • Have the vehicle repaired immediately. Never park the vehicle with the engine running in an enclosed area such as a garage or a building that has no fresh air ventilation. Running the Vehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. { WARNING: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains Carbon WARNING: (Continued) WARNING: (Continued) { WARNING: Four-wheel drive vehicles with the transfer case in N (Neutral) will allow the vehicle to roll, even if the automatic transmission shift lever is in P (Park). So, be sure the transfer case is in a drive gear — not in N (Neutral). Always set the parking brake. Follow the proper steps to be sure the vehicle will not move. See Shifting Into Park (Automatic Transmission) on page 3-31. If pulling a trailer, see Towing a Trailer on page 5-48. Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. Never run the engine in an enclosed area that has no fresh air ventilation. For more information, see Engine Exhaust on page 3-34. { WARNING: It can be dangerous to get out of the vehicle if the automatic transmission shift lever is not fully in P (Park) with the parking brake ﬁrmly set. The vehicle can roll. Do not leave the vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure the vehicle will not move, even when it is on fairly level ground, always set the parking brake and move the automatic transmission shift lever to P (Park), or the manual transmission shift lever to Neutral. 3-35 Mirrors Manual Rearview Mirror Hold the inside rearview mirror in the center to move it for a clearer view of behind your vehicle. Adjust the mirror to avoid glare from the headlamps behind you. Push the tab forward for daytime use and pull it for nighttime use. Vehicles with OnStar® have three additional control buttons located at the bottom of the mirror. See your dealer/retailer for more information on the system and how to subscribe to OnStar. See the OnStar ® owners guide for more information about the services OnStar provides. Adjust this type of mirror to avoid glare from the headlamps behind you by turning the knob counterclockwise for nighttime driving and clockwise for daytime driving. Cleaning the Mirror Do not spray glass cleaner directly on the mirror. Use a soft towel dampened with water. Automatic Dimming Rearview Mirror The vehicle may have an automatic dimming inside rearview mirror. Automatic dimming reduces the glare of lights from behind the vehicle. The mirror may also have OnStar® and/or a compass and outside temperature display. Control buttons for the OnStar® system are at the bottom of the mirror. See the OnStar® owners guide for more information about the services OnStar® provides. See Compass on page 3-37 for more information about the compass display. See “Temperature Display” after, for more information about the outside temperature display. AUTO/ ( / O (On/Off): Press and hold AUTO / ( for about three seconds or depending on the mirror, press O to turn automatic dimming on or off. The automatic dimming feature comes on and the indicator light illuminates each time the vehicle is started. 3-36 Temperature Display Y b / O (On/Off): Press Y b or depending on the mirror, press O to turn the display on or off. To adjust between Fahrenheit and Celsius: 1. Press and hold Y b / O for a few seconds. The current unit of measure (F or C) ﬂashes. 2. Press Y b / O again and release to change the unit of measure. Wait several seconds and the compass/temperature display returns with the selected unit of measure. It is normal under certain conditions for the temperature update to be delayed. If an incorrect temperature displays for an extended period, see your dealer/retailer. Cleaning the Mirror Do not spray glass cleaner directly on the mirror. Use a soft towel dampened with water. Compass Compass Operation Press Y b or depending on the mirror, press O once to turn the display on or off. Compass Calibration The compass may need calibration if: • CAL is displayed while driving in the vehicle. • After approximately ﬁve seconds, the display does not show a compass heading, N for North, for example, there may be a strong magnetic ﬁeld interfering with the compass. Interference can be caused by a magnetic antenna mount, magnetic note pad holder, or a similar magnetic item. • The compass does not display the correct heading and the compass zone variance is set correctly. To calibrate, CAL must be displayed in the mirror compass windows. If CAL is not displayed, press and hold Y b / O for several seconds or until CAL is displayed. The compass can be calibrated by driving the vehicle in circles at 5 mph (8 km/h) or less until the display reads a direction. 3-37 Compass Variance The mirror is set to zone eight. If you do not live in zone eight or drive out of the area, the compass variance needs to be changed to the appropriate zone. To adjust for compass variance: 1. Find the current location and variance zone number on the following zone map. 3. Press Y b / O repeatedly until the new zone number displays. After you stop pressing the button, the display shows a compass direction within a few seconds. Outside Manual Mirrors Manually fold the mirrors inward to prevent damage when going through an automatic car wash. To fold, push the mirrors toward the vehicle. Push outward, to return the mirrors to their original position. Outside Power Mirrors Vehicles with outside power mirrors have controls on the driver door armrest. 2. Press and hold Y b / O until Z and/or a zone number displays. 3-38 To adjust the power mirrors: 1. Move the selector switch to the L (left) or R (right) to choose the driver or passenger mirror. 2. Press one of the four buttons located on the control pad to move the mirror to the desired direction. 3. Return the selector switch to the center position once the mirrors are adjusted. If the mirror begins making a ratcheting sound, the mirror has reached the end of its travel and can go no farther in that direction. To stop the sound, reverse the mirror direction using the control pad. Manually fold the mirrors inward to prevent damage when going through an automatic car wash. To fold, push the mirror toward the vehicle. Push outward, to return the mirror to its original position. Outside Convex Mirror { WARNING: A convex mirror can make things, like other vehicles, look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on the right. Check the inside mirror or glance over your shoulder before changing lanes. The passenger side mirror is convex shaped. A convex mirror’s surface is curved so more can be seen from the driver seat. 3-39 Storage Areas Glove Box Lift up on the glove box lever to open it. Cupholders This vehicle may have two cupholders located on the lower part of the front doors as well as two cupholders located at the front end of the console. Vehicles with bench seats may have cupholders attached to the front of the center seat. For vehicles that are an extended cab or crew cab model, the vehicle also has two rear cupholders. On crew cab models, the cupholders are located at the front end of the rear center seat cushion. On extended cab models, the rear seat cupholders are located on top of the rear center console. Vehicles with ashtrays will use one of the cupholders. Center Console Storage For vehicles with bench seats, there may be a center armrest storage area. Lift up on the upper tab located at the front of the armrest to release the latch. Lift the lid to open the storage area. For vehicles with bucket seats or uplevel packages, the vehicle may have a two-tiered center armrest storage area. Lift up on the upper tab located at the front of the armrest to release the latch. Lift the lid to the top storage area. A second tab is located below the top one and allows you to access the bottom storage area. Lift up on the lower tab to release the latch. Then, raise the lid of the lower storage area. The upper storage area will lift up with the lid of the lower storage area. To close the storage area(s), lower the lid(s) until you feel the latch close. Assist Handles This vehicle may have assist handles to be used when getting out of the vehicle. The assist handles are located above the doors. If the vehicle has roof-mounted side impact air bags, there are assist handles located above both the driver and front passenger doors. 3-40 Rear Storage Area Extended cab models might have storage compartments under the rear seats. To access the storage compartments, lift the cushion on the bottom of the rear seats. This exposes the storage boxes under the seat. To open a storage box, unhook the bottom and lift the two latches on each side of the storage box. 3-41 Sunroof The vehicle may have a sunroof. The sunroof control buttons are located on the headliner. Q (Open/Vent): Press and hold this button to vent, and open the sunroof. Release the button when the desired position is reached. R (Close): Press and hold this button to close the sunroof. Release the button when the desired position is reached. The sunshade must be opened manually. Lift the lid from the center area to access the storage box. 3-42 Section 4 Instrument Panel Instrument Panel Overview ...............................4-3 Hazard Warning Flashers ................................4-3 Horn .............................................................4-3 Tilt Wheel .....................................................4-3 Turn Signal/Multifunction Lever .........................4-4 Turn and Lane-Change Signals ........................4-4 Headlamp High/Low-Beam Changer ..................4-5 Flash-to-Pass .................................................4-5 Windshield Wipers ..........................................4-5 Windshield Washer .........................................4-6 Cruise Control ................................................4-7 Exterior Lamps .............................................4-10 Headlamps on Reminder ................................4-11 Daytime Running Lamps (DRL) .......................4-11 Automatic Headlamp System ..........................4-12 Fog Lamps ..................................................4-12 Exterior Cargo Lamps ....................................4-13 Instrument Panel Brightness ...........................4-13 Dome Lamp .................................................4-13 Dome Lamp Override ....................................4-14 Exit Lighting .................................................4-14 Electric Power Management ...........................4-14 Battery Run-Down Protection ..........................4-15 Accessory Power Outlet(s) .............................4-15 Ashtray(s) and Cigarette Lighter ......................4-16 Climate Controls ............................................4-16 Climate Control System .................................4-16 Outlet Adjustment .........................................4-18 Warning Lights, Gages, and Indicators ............4-18 Instrument Panel Cluster ................................4-19 Speedometer and Odometer ...........................4-20 Trip Odometer ..............................................4-20 Tachometer .................................................4-20 Safety Belt Reminders ...................................4-21 Airbag Readiness Light ..................................4-22 Passenger Airbag Status Indicator ...................4-23 Charging System Light ..................................4-24 Up-Shift Light ...............................................4-24 Brake System Warning Light ..........................4-25 Antilock Brake System (ABS) Warning Light .....4-26 StabiliTrak®/Traction Control System (TCS) Warning Light ...........................................4-26 Engine Coolant Temperature Gage ..................4-27 Tire Pressure Light .......................................4-28 Malfunction Indicator Lamp .............................4-28 Oil Pressure Light .........................................4-31 Security Light ...............................................4-32 Cruise Control Light ......................................4-32 Highbeam On Light .......................................4-32 Fuel Gage ...................................................4-32 4-1 Section 4 Instrument Panel Driver Information Center (DIC) .......................4-33 DIC Operation and Displays ...........................4-33 DIC Warnings and Messages .........................4-37 Audio System(s) .............................................4-42 Setting the Clock ..........................................4-43 Radio(s) ......................................................4-43 Using an MP3 ..............................................4-56 XM Radio Messages .....................................4-60 Theft-Deterrent Feature ..................................4-61 Radio Reception ...........................................4-61 Fixed Mast Antenna ......................................4-63 XM™ Satellite Radio Antenna System .............4-63 Chime Level Adjustment ................................4-63 4-2 Instrument Panel Overview Tilt Wheel Hazard Warning Flashers | (Hazard Warning Flasher): Press this button located on the instrument panel, to make the front and rear turn signal lamps ﬂash on and off. This warns others that you are having trouble. Press | again to turn the ﬂashers off. The turn signals do not work while the hazard warning ﬂashers are on. Horn To sound the horn, press the horn symbol on the steering wheel pad. To adjust the steering wheel: 1. Hold the steering wheel and pull the lever toward you. 2. Move the steering wheel up or down into a comfortable position. 3. Release the lever to lock the wheel in place. Do not adjust the steering wheel while driving. 4-3 Turn Signal/Multifunction Lever Turn and Lane-Change Signals An arrow on the instrument panel cluster ﬂashes in the direction of the turn or lane change. Move the lever all the way up or down to signal a turn. Raise or lower the lever until the arrow starts to ﬂash to signal a lane change. Hold it there until the lane change is complete. The lever returns to its starting position when it is released. If after signaling a turn or a lane change the arrows ﬂash rapidly or do not come on, a signal bulb may be burned out. Have the bulbs replaced. If the bulb is not burned out, check the fuse. For bulb replacement, see Taillamps, Turn Signal, Stoplamps and Back-up Lamps on page 6-53. For a blown fuse or circuit breaker, see Fuses and Circuit Breakers on page 6-111. The lever on the left side of the steering column includes the following: G : Turn and Lane Change Signals 5 3 : Headlamp High/Low-Beam Changer N : Windshield Wipers L : Windshield Washer J : Cruise Control Flash-to-Pass. Information for these features is on the pages following. 4-4 Turn Signal On Chime If a turn signal is left on for more than 3/4 of a mile (1.2 km), a chime will sound at each ﬂash of the turn signal and the message TURN SIGNAL will also appear in the DIC. To turn the chime and message off, move the turn signal lever to the off position. See “TURN SIGNAL” under DIC Warnings and Messages on page 4-37 for more information. Headlamp High/Low-Beam Changer 2 3 Headlamp High/Low Beam Changer: Push the turn signal/multifunction lever away from you to turn the high beams on. Pull the lever towards you to return to low beams. This indicator light turns on in the instrument panel cluster when the high beam headlamps are on. Flash-to-Pass This feature lets you use the high-beam headlamps to signal a driver in front of you that you want to pass. It works even if the headlamps are in the automatic position. To use it, pull the turn signal lever toward you, then release it. If the headlamps are in the automatic position or on low beam, the high-beam headlamps will turn on. They will stay on as long as the lever is held toward you. The high-beam indicator on the instrument panel cluster will come on. Release the lever to return to normal operation. Windshield Wipers The windshield wiper controls are located on the multifunction lever. They are controlled by turning the band with this z symbol. The windshield wipers work in all ignition positions, except off. This includes the Retained Access Power mode. See Retained Accessory Power (RAP) on page 3-18. 4-5 Move the band to one of the following positions: 8 (Mist): Single wipe, move the band to z and then release it. Several wipes, hold the band on z longer. N (Adjustable Interval Wipes): For a delayed wiping cycle. Turn the band up for more frequent wipes or down for less frequent wipes. 6 (Low Speed): Slow wipes, turn the band to the ﬁrst solid position past the delay settings. 1 (High Speed): Fast wipes, turn the band to the second solid position past the delay settings. 9 (Off): Turns the wipers off. Clear snow and ice from the wiper blades before using them. If frozen to the windshield, carefully loosen or thaw them. Damaged wiper blades should be replaced. Windshield Washer { WARNING: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. Q L (Washer Fluid): There is a paddle marked with the windshield washer symbol at the top of the multifunction lever. To spray washer ﬂuid on the windshield, push the paddle. The wipers will clear the window and then either stop or return to your preset speed. 4-6 Cruise Control With cruise control, a speed of about 40 km/h (25 mph) or more can be maintained without keeping your foot on the accelerator. Cruise control does not work at speeds below about 40 km/h (25 mph). Cruise control will not work if the parking brake is set, or if the master cylinder brake ﬂuid level is low. If the brakes are applied, the cruise control shuts off. { WARNING: Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use the cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control. Do not use cruise control on slippery roads. If the vehicle’s StabiliTrak® /Traction Control System (TCS) begins to limit wheel spin while the cruise control is on, the cruise control automatically disengages. See StabiliTrak® System on page 5-6 or Traction Control System (TCS) on page 5-8. When road conditions allow you to safely use it again, the cruise control can be turned back on. These controls are located at the end of the multifunction lever. 9 (Off): Turns the system off. R (On): Turns the system on. + (Resume/Accelerate): Use to make the vehicle accelerate or resume a previously set speed. r T (Set): Press the button at the end of the lever to set the speed. 4-7 Setting Cruise Control { WARNING: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control. 1. Move the cruise control lever to on. 2. Get up to the speed desired. 3. Press r T at the end of the lever and release it. 4. Take your foot off the accelerator pedal. 4-8 This light on the instrument panel cluster comes on while the cruise control is on. Resuming a Set Speed If the cruise control is set to a desired speed and then the brake is applied, the cruise control is disengaged. But it does not need to be reset. Once the vehicle is going about 40 km/h (25 mph) or more, move the cruise control switch brieﬂy from R to S . The vehicle will go right back up to your chosen speed and stay there. If the lever is held at resume/accelerate the vehicle keeps going faster until the lever is released or the brake is applied. Do not hold the lever at resume/accelerate, unless you want the vehicle to go faster. Increasing Speed While Using Cruise Control There are two ways to go to a higher speed: • Use the accelerator pedal to get to the higher speed. Press r T at the end of the lever, then release the button and the accelerator pedal. The vehicle will cruise at the higher speed. If the accelerator pedal is held longer than 60 seconds, cruise control will turn off. • Move the cruise lever from R to S . Hold it there until the desired speed is reached, and then release the lever. To increase the vehicle speed in very small amounts, move the lever brieﬂy to S . Reducing Speed While Using Cruise Control • Press and hold r T until the lower speed desired is reached, then release it. • To slow down in very small amounts, brieﬂy press r T . Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase the vehicle speed. When you take your foot off the pedal, the vehicle slows down to the cruise control speed you set earlier. Using Cruise Control on Hills How well the cruise control works on hills depends upon the vehicle speed, load, and the steepness of the hills. When going up steep hills, you might have to step on the accelerator pedal to maintain the vehicle speed. When going downhill, you might have to brake or shift to a lower gear to keep the vehicle speed down. Applying the brake will turn off the cruise control. Ending Cruise Control To turn off the cruise control, do one of the following: • Step lightly on the brake pedal. • Move the cruise control lever to 9 . • Lightly tap or press the clutch, if you have a manual transmission. Erasing Speed Memory The cruise control set speed memory is erased when the cruise control or the ignition is turned off. 4-9 AUTO: Turns the headlamps on automatically at normal brightness, together with the following: • Sidemarker Lamps • Taillamps • Parking Lamps • Instrument Panel Lights See Automatic Headlamp System on page 4-12 for more information. ; (Parking Lamps): Turns on the parking lamps, together with the following: • Sidemarker Lamps • Taillamps • License Plate Lamps • Instrument Panel Lights 2 (Headlamps): Turns on the headlamps, together with the previously listed lamps and lights. Exterior Lamps The exterior lamp control is located on the instrument panel on the left side of the steering wheel. O (Exterior Lamps): Turn the knob, located to the right of this symbol, to choose one of the four exterior lamp positions. O (Off): Turns off all exterior lamps including the Daytime Running Lamps (DRL). 4-10 Headlamps on Reminder If a door is open, a reminder chime sounds when the headlamps or parking lamps are manually turned on and the key is out of the ignition. To turn off the chime, turn the headlamp switch to off and then back on. In the automatic mode, the headlamps turn off once the ignition is in LOCK/OFF. For vehicles ﬁrst sold in Canada, if the parking lamps are turned on manually, the Daytime Running Lamps (DRL) will stay on. Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. Fully functional daytime running lamps are required on all vehicles ﬁrst sold in Canada. The DRL system will come on when the following conditions are met: • The ignition is on. • The exterior lamps control is in AUTO. • The transmission is not in P (Park) if you have an automatic transmission. • The light sensor determines it is daytime. When the DRL are on, only the parking lamps or reduced intensity low beam headlamps will be on. The taillamps, sidemarkers, and other lamps will not be on. The instrument panel will not be lit up either. When it begins to get dark, the headlamps will automatically switch from DRL to the regular headlamps. The regular headlamp system should be turned on when needed. 4-11 Automatic Headlamp System When it is dark enough outside, the automatic headlamp system will turn on after the transmission has been shifted from P (Park) to D (Drive). The headlamps, taillamps, sidemarker, parking lamps, roof marker lamps, and the instrument panel lights turn on at normal brightness. The radio lights will become dimmer when the headlights are off compared to when the headlights are on. The vehicle has a light sensor located on the top of the instrument panel. Do not cover the sensor, or the system will be on whenever the ignition is on. The system can turn on the headlamps when driving in a parking garage, through a tunnel or when there is overcast weather. This is normal. There is a delay in the transition between the daytime and nighttime operation of the Daytime Running Lamps (DRL) and the automatic headlamp system so that driving under bridges or bright overhead street lights does not affect the system. The DRL and automatic headlamp system will only be affected when the light sensor detects a change in lighting lasting longer than the delay. If the vehicle is started in a dark garage, the automatic headlamp system will come on immediately. Once the vehicle leaves the garage, it will take about one minute for the automatic headlamp system to change to DRL if it is light outside. During that delay, the instrument panel cluster may not be as bright as usual. Make sure the instrument panel brightness control is in the full bright position. See Instrument Panel Brightness on page 4-13. Fog Lamps The fog lamp button is located near the exterior lamps control. # : For vehicles with fog lamps, press to turn the fog lamps on or off. An indicator light will turn on in the button when the fog lamps are on. The parking lamps or low-beam headlamps must be on for the fog lamps to work. The fog lamps will go off whenever the high-beam headlamps come on. When the high beams go off, the fog lamps come on again. Some localities have laws that require the headlamps to be on along with the fog lamps. 4-12 Exterior Cargo Lamps The cargo lamps can be used if more light is needed in the cargo area of the vehicle or in the top-box storage units. This button is located on the driver side of the instrument panel near the exterior lamp control. Press to turn the cargo lamps on and off. The dome lamps must be on for the cargo lamps to come on. See Dome Lamp on page 4-13. Instrument Panel Brightness D (Instrument Panel Lights): Turn the thumbwheel up or down to brighten or dim the instrument panel lights and the radio display. The instrument panel lights, cluster, and radio display do not dim to complete darkness. The instrument panel light brightness control will only work if the headlamps or parking lamps are on. See Exterior Lamps on page 4-10. Dome Lamp The dome lamps, located in the front and cargo area of the vehicle, come on when any door is opened. Turn the dome lamps on by turning the thumbwheel, located next to the exterior lamps control, all the way up. In this position, the lamps remain on whether a door is opened or closed. Reading Lamps Press the lens on the lamps to turn each reading lamp on or off. These lamps will not come on with the dome lamps. 4-13 Dome Lamp Override The dome lamp override button is located below the exterior lamps control. E (Dome Lamp Override): Press this button in to make the dome lamps remain off when the doors are open. To return the lamps to automatic operation, press E again and return it to the out position. Exit Lighting The interior lamps will come on when the key is removed from the ignition. The lamps will not come on if the dome override button is pressed in. Electric Power Management The vehicle has Electric Power Management (EPM) that estimates the battery’s temperature and state of charge. It then adjusts the voltage for best performance and extended life of the battery. When the battery’s state of charge is low, the voltage is raised slightly to quickly bring the charge back up. When the state of charge is high, the voltage is lowered slightly to prevent overcharging. If the vehicle has a voltmeter gage or a voltage display on the Driver Information 4-14 Center (DIC), you may see the voltage move up or down. This is normal. If there is a problem, an alert will be displayed. The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all the power that is needed for very high electrical loads. A high electrical load occurs when several of the following are on, such as: headlamps, high beams, fog lamps, rear window defogger, climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets. EPM works to prevent excessive discharge of the battery. It does this by balancing the generator’s output and the vehicle’s electrical needs. It can increase engine idle speed to generate more power, whenever needed. It can temporarily reduce the power demands of some accessories. Normally, these actions occur in steps or levels, without being noticeable. In rare cases at the highest levels of corrective action, this action may be noticeable to the driver. If so, a Driver Information Center (DIC) message might be displayed, such as BATTERY SAVER ACTIVE, BATTERY VOLTAGE LOW, or LOW BATTERY. If this message is displayed, it is recommended that the driver reduce the electrical loads as much as possible. See DIC Warnings and Messages on page 4-37. Battery Run-Down Protection This feature shuts off the dome lamp if it is left on for more than 20 minutes when the ignition is in LOCK/OFF. This helps to prevent the battery from running down. Accessory Power Outlet(s) The accessory power outlets can be used to connect electrical equipment such as a cellular phone. The vehicle may have an accessory power outlet located below the climate control system and on the rear of the center console. A small cap must be pulled down to access an accessory power outlet. When not using an outlet be sure to cover it with the protective cap. Notice: Leaving electrical equipment on for extended periods will drain the battery. Always unplug electrical equipment when not in use and do not plug in equipment that exceeds the maximum amperage rating of 20 amperes. Certain electrical accessories may not be compatible with the accessory power outlet and could result in blown vehicle or adapter fuses. If you experience a problem, see your dealer/retailer for additional information on accessory power outlets. Notice: Adding any electrical equipment to the vehicle can damage it or keep other components from working as they should. The repairs would not be covered by the vehicle warranty. Do not use equipment exceeding maximum amperage rating of 20 amperes. Check with your dealer/retailer before adding electrical equipment. When adding electrical equipment, be sure to follow the proper installation instructions included with the equipment. Notice: cause damage not covered by the vehicle warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only. Improper use of the power outlet can 4-15 If papers, pins, or other ﬂammable items Ashtray(s) and Cigarette Lighter The vehicle may have a removable ashtray and cigarette lighter. The ashtray is located in the center console area. The ashtray can be removed for cleaning. When the ashtray is removed, this area can also be used as a cupholder. Notice: are put in the ashtray, hot cigarettes or other smoking materials could ignite them and possibly damage the vehicle. Never put ﬂammable items in the ashtray. To use the lighter, press it in all the way, and let go. When it is ready, it will pop back out by itself. Notice: Holding a cigarette lighter in while it is heating does not let the lighter back away from the heating element when it is hot. Damage from overheating can occur to the lighter or heating element, or a fuse could be blown. Do not hold a cigarette lighter in while it is heating. 4-16 Climate Controls Climate Control System The heating, cooling, and ventilation for the vehicle can be controlled with this system. A. Temperature Control B. Fan Control C. Air Delivery Mode Control D. Air Conditioning E. Recirculation Temperature Control: Turn the knob clockwise or counterclockwise to increase or decrease the temperature of the air inside the vehicle. 9 (Fan Control): Turn the knob clockwise or counterclockwise to increase or decrease the fan speed. If the knob is set on “0” (zero), some outside air will still enter the vehicle and will be directed according to the position of the mode knob. Air Delivery Mode Control: Turn the knob clockwise or counterclockwise to change the current airﬂow mode. Select from the following modes: H (Vent): Air is directed to the instrument panel outlets. \ (Bi-Level): Air is divided between the instrument panel outlets and ﬂoor and side window outlets. Cooler air is directed to the upper outlets and warmer air to the ﬂoor outlets. [ (Floor): Air is directed to the ﬂoor outlets. Recirculation cannot be selected while in ﬂoor mode because this could cause the interior window to fog. / (Floor/Defog): This mode clears the windows of fog or moisture. Air is directed to the ﬂoor, windshield, and side window outlets. When this mode is selected, the system runs the air conditioning compressor unless the outside temperature is near freezing or below. Recirculation is not available in this mode. 0 (Defrost): This mode clears the windshield of fog or frost more quickly. Air is directed to the windshield and side window outlets. When this mode is selected, the system runs the air conditioning compressor unless the outside temperature is near, or below freezing. Recirculation is not available in this mode. Do not drive the vehicle until all the windows are clear. # (Air Conditioning): Press to turn the air conditioning system on or off. An indicator light on the button comes on to show that the air conditioning is on. The fan control must be on to use the air conditioning. There might be a slight change in engine performance when the air conditioning compressor shuts off and turns on again. This is normal. The system is designed to make adjustments to help with fuel economy while still maintaining the selected temperature. The air conditioning system removes moisture from the air, so a small amount of water might drip under the vehicle while idling or after turning off the engine. This is normal. @ (Recirculation): Press to turn the recirculation mode on or off. An indicator light on the button comes on to show that the recirculation mode is on. This mode recirculates and helps to quickly cool the air inside the vehicle. It can be used to prevent outside air and odors from entering the vehicle. 4-17 The recirculation mode cannot be used with ﬂoor/defog, defrost, or defogging modes. If recirculation is selected in these modes, the indicator will ﬂash or not come on. Outlet Adjustment Use the thumbwheel on the outlets to change the direction of the air ﬂow. Lift up or push down on the thumbwheel located in the center of the outlet to direct the air up or down, or slide the thumbwheel to the left or right to direct the airﬂow from side-to-side. Operation Tips • Clear away any ice, snow or leaves from the air inlets at the base of the windshield that may block the ﬂow of air into the vehicle. • Use of non-GM approved hood deﬂectors may adversely affect the performance of the system. • Keep the path under the front seats clear of objects to help circulate the air inside of the vehicle more effectively. Warning Lights, Gages, and Indicators Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to the warning lights and gages could prevent injury. Warning lights come on when there might be or there is a problem with one of the vehicle’s functions. Some warning lights come on brieﬂy when the engine is started to indicate they are working. Gages can indicate when there might be or there is a problem with one of the vehicle’s functions. Often gages and warning lights work together to indicate a problem with the vehicle. When one of the warning lights comes on and stays on while driving, or when one of the gages shows there could be a problem, check the section that explains what to do. Follow this manual’s advice. Waiting to do repairs can be costly and even dangerous. 4-18 Instrument Panel Cluster The instrument panel cluster is designed to show how the vehicle is running. It shows how fast the vehicle is going, about how much fuel has been used, and many other things needed to drive safely and economically. United States automatic transmission 2.9L version shown, Canada, manual transmission, 3.7L and 5.3L similar 4-19 Speedometer and Odometer The speedometer shows the speed in both miles per hour (mph) and kilometers per hour (km/h). The odometer shows how far the vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). The odometer mileage can be checked without the vehicle running by pressing the trip information stem. See “Odometer” under DIC Operation and Displays on page 4-33 for more information. If the cluster is replaced the new one will automatically detect and update the vehicle’s accumulated mileage. Trip Odometer The vehicle has a trip odometer that indicates how far the vehicle has been driven since the trip odometer was last set to zero. See “Trip Odometer” under DIC Operation and Displays on page 4-33 for more information. Tachometer The tachometer displays the engine speed in revolutions per minute (rpm). Notice: tachometer in the shaded warning area, the vehicle could be damaged, and the damages would not be covered by the vehicle warranty. Do not operate the engine with the tachometer in the shaded warning area. If the engine is operated with the 4-20 Safety Belt Reminders Safety Belt Reminder Light When the engine is started, a chime sounds for several seconds to remind a driver to fasten the safety belt, unless the driver safety belt is already buckled. The safety belt light comes on and stays on for several seconds, then ﬂashes for several more. Passenger Safety Belt Reminder Light For vehicles equipped with the passenger safety belt reminder light, several seconds after the engine is started, a chime sounds for several seconds to remind the front passenger to buckle their safety belt. The passenger safety belt light, located on the instrument panel, comes on and stays on for several seconds and then ﬂashes for several more. This chime and light are repeated if the passenger remains unbuckled and the vehicle is in motion. This chime and light are repeated if the driver remains unbuckled and the vehicle is in motion. If the driver safety belt is already buckled, neither the chime nor the light comes on. If the passenger safety belt is buckled, neither the chime nor the light comes on. The front passenger safety belt warning light and chime may turn on if an object is put on the seat such as a briefcase, handbag, grocery bag, laptop or other electronic device. To turn off the warning light and or chime, remove the object from the seat or buckle the safety belt. 4-21 Airbag Readiness Light The system checks the airbag’s electrical system for possible malfunctions. If the light stays on it indicates there is an electrical problem. The system check includes the airbag sensor, the pretensioners, the airbag modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 2-64. The airbag readiness light ﬂashes for a few seconds when the engine is started. If the light does not come on then, have it ﬁxed immediately. { WARNING: If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inﬂate in a crash, or they could even inﬂate without a crash. To help avoid injury, have the vehicle serviced right away. If there is a problem with the airbag system, an airbag Driver Information Center (DIC) message can also come on. See DIC Warnings and Messages on page 4-37 for more information. 4-22 Passenger Airbag Status Indicator If the vehicle has one of the passenger airbag status indicators pictured in the following illustrations, then the vehicle has a passenger sensing system for the right front passenger position. The passenger airbag status indicator is on the instrument panel. See Passenger Sensing System on page 2-73 for important safety information. In addition, if the vehicle has a passenger sensing system for the right front passenger position, the label on the vehicle’s sun visors refer to “ADVANCED AIRBAGS”. United States Canada When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check. Then, after several more seconds, the status indicator will light either ON or OFF, or either the on or off symbol to let you know the status of the right front passenger frontal airbag. If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger frontal airbag is enabled (may inﬂate). If the word OFF or the off symbol is lit on the airbag status indicator, it means that the passenger sensing system has turned off the right front passenger frontal airbag. If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer/retailer for service. { WARNING: If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light on page 4-22 for more information, including important safety information. 4-23 Charging System Light Up-Shift Light This light comes on brieﬂy when the ignition key is turned to START, but the engine is not running, as a check to show it is working. The vehicle may have an up-shift light. When this light comes on, shift to the next higher gear if weather, road, and traffic conditions allow. See Manual Transmission Operation on page 3-23 for more information. If it does not, have the vehicle serviced by your dealer/retailer. The light should go out once the engine starts. If it stays on, or comes on while driving, there could be a problem with the charging system. A charging system message in the Driver Information Center (DIC) can also appear. See DIC Warnings and Messages on page 4-37 for more information. This light could indicate that there are problems with a generator drive belt, or that there is an electrical problem. Have it checked right away. If the vehicle must be driven a short distance with the light on, turn off accessories, such as the radio and air conditioner. 4-24 Brake System Warning Light The vehicle’s hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop the vehicle. For good braking though, both parts need to be working well. If the warning light comes on, there could be a brake problem. Have the brake system inspected right away. United States Canada This light comes on brieﬂy when the ignition key is turned to ON/RUN. If it does not, have it ﬁxed so it will be ready to warn if there is a problem. When the ignition is on, the brake system warning light comes on when the parking brake is set. See Parking Brake on page 3-30 for more information. The light stays on if the parking brake does not release fully. If it stays on after the parking brake is fully released, it means there is a brake problem. If the light comes on while driving, pull off the road and stop. The brake pedal might be harder to push, or it might go closer to the ﬂoor. It can take longer to stop. If the light is still on, have the vehicle towed for service. See Towing Your Vehicle on page 5-41. { WARNING: The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service. 4-25 Antilock Brake System (ABS) Warning Light StabiliTrak®/Traction Control System (TCS) Warning Light The Antilock Brake System (ABS) light comes on brieﬂy when the engine is started. The StabiliTrak and Traction Control System (TCS) indicator/warning light comes on brieﬂy while starting the engine. If it does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the indicator light then goes off. The light ﬂashes while the StabiliTrak system and TCS are working to assist the driver with directional control of the vehicle in difficult driving conditions. If it does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the indicator light then goes off. If the ABS light stays on, turn the ignition off. If the light comes on while driving, stop as soon as it is safely possible and turn the ignition off. Then start the engine again to reset the system. If the ABS light stays on, or comes on again while driving, the vehicle needs service. If the regular brake system warning light is not on, the vehicle still has brakes, but not antilock brakes. If the regular brake system warning light is also on, the vehicle does not have antilock brakes and there is a problem with the regular brakes. See Brake System Warning Light on page 4-25. See DIC Warnings and Messages on page 4-37 for all brake related DIC messages. 4-26 If the StabiliTrak system and TCS light comes on and stays on while driving and a TRACTION FAULT or SERVICE STAB SYS message displays on the DIC, the vehicle needs service. The light also comes on steady when the StabiliTrak system and/or TCS are turned off. The DIC also displays a TRAC OFF and/or STAB SYS OFF message. If the TCS is off, wheel spin is not limited. If the StabiliTrak system is off, the system does not assist the driver with directional control of the vehicle. The light turns off when the TCS and StabiliTrak system are turned back on. See StabiliTrak® System on page 5-6, Traction Control System (TCS) on page 5-8 and DIC Warnings and Messages on page 4-37 for more information. Engine Coolant Temperature Gage This gage shows the engine coolant temperature. If the gage pointer is near the top of the gage, the engine is too hot. It means that the engine coolant has overheated. If the vehicle has been operating under normal driving conditions, pull the vehicle off the road, stop the vehicle and turn off the engine as soon as possible. See Engine Overheating on page 6-35 for more information. 4-27 Tire Pressure Light For vehicles with a tire pressure monitoring system, this light comes on brieﬂy when the engine is started. It provides information about tire pressures and the Tire Pressure Monitoring System. When the Light is On Steady This indicates that one or more of the tires are signiﬁcantly underinﬂated. A tire pressure message in the Driver Information Center (DIC), can accompany the light. See Driver Information Center (DIC) on page 4-33 for more information. Stop and check the tires as soon as it is safe to do so. If underinﬂated, inﬂate to the proper pressure. See Inﬂation - Tire Pressure on page 6-64 for more information. 4-28 When the Light Flashes First and Then is On Steady This indicates that there may be a problem with the Tire Pressure Monitor System. The light ﬂashes for about a minute and stays on steady for the remainder of the ignition cycle. This sequence repeats with every ignition cycle. See Tire Pressure Monitor Operation on page 6-67 for more information. Malfunction Indicator Lamp Check Engine Light A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors operation of the fuel, ignition, and emission control systems. It ensures that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment. This light should come on when the ignition is on, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer/retailer. If the check engine light comes on and stays on, while the engine is running, this indicates that there is an OBD II problem and service is required. Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light can prevent more serious damage to the vehicle. This system assists the service technician in correctly diagnosing any malfunction. Notice: If the vehicle is continually driven with this light on, after a while, the emission controls might not work as well, the vehicle’s fuel economy might not be as good, and the engine might not run as smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty. Notice: Modiﬁcations made to the engine, transmission, exhaust, intake, or fuel system of the vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect the vehicle’s emission controls and can cause this light to come on. Modiﬁcations to these systems could lead to costly repairs not covered by the vehicle warranty. This could also result in a failure to pass a required Emission Inspection/Maintenance test. See Accessories and Modiﬁcations on page 6-3. This light comes on during a malfunction in one of two ways: Light Flashing: A misﬁre condition has been detected. A misﬁre increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required. To prevent more serious damage to the vehicle: • Reduce vehicle speed. • Avoid hard accelerations. • Avoid steep uphill grades. • If towing a trailer, reduce the amount of cargo being hauled as soon as it is possible. If the light continues to ﬂash, when it is safe to do so, stop the vehicle. Find a safe place to park the vehicle. Turn the key off, wait at least 10 seconds, and restart the engine. If the light is still ﬂashing, follow the previous steps and see your dealer/retailer for service as soon as possible. 4-29 Light On Steady: An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required. An emission system malfunction might be corrected by doing the following: • Make sure the fuel cap is fully installed. See Filling the Tank on page 6-8. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off. • If the vehicle has been driven through a deep puddle of water, the vehicle’s electrical system might be wet. The condition is usually corrected when the electrical system dries out. A few driving trips should turn the light off. • Make sure to fuel the vehicle with quality fuel. Poor fuel quality causes the engine not to run as efficiently as designed and can cause: stalling after start-up, stalling when the vehicle is changed into gear, misﬁring, hesitation on acceleration, or stumbling on acceleration. These conditions might go away once the engine is warmed up. If one or more of these conditions occurs, change the fuel brand used. It will require at least one full tank of the proper fuel to turn the light off. See Gasoline Octane on page 6-5. If none of the above have made the light turn off, your dealer/retailer can check the vehicle. The dealer/retailer has the proper test equipment and diagnostic tools to ﬁx any mechanical or electrical problems that might have developed. 4-30 Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration. Here are some things to know to help the vehicle pass an inspection: • The vehicle will not pass this inspection if the check engine light is on with the engine running, or if the key is in ON/RUN and the light is not on. • The vehicle will not pass this inspection if the OBD II (on-board diagnostic) system determines that critical emission control systems have not been completely diagnosed by the system. The vehicle would be considered not ready for inspection. This can happen if the battery has recently been replaced or if the battery has run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This can take several days of routine driving. If this has been done and the vehicle still does not pass the inspection for lack of OBD II system readiness, your dealer/retailer can prepare the vehicle for inspection. Oil Pressure Light { WARNING: Do not keep driving if the oil pressure is low. The engine can become so hot that it catches ﬁre. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced. Notice: Lack of proper engine oil maintenance can damage the engine. The repairs would not be covered by the vehicle warranty. Always follow the maintenance schedule in this manual for changing engine oil. This light comes on brieﬂy while starting the engine. If it does not, have the vehicle serviced by your dealer/ retailer. If the system is working normally the indicator light then goes off. 4-31 If the light comes on and stays on, it means that oil is not ﬂowing through the engine properly. The vehicle could be low on oil and it might have some other system problem. Security Light Highbeam On Light This light comes on when the high-beam headlamps are in use. For information regarding this light and the vehicle’s security system, see Content Theft-Deterrent on page 3-13. See Headlamp High/Low-Beam Changer on page 4-5 for more information. Fuel Gage Cruise Control Light The cruise control light comes on whenever the cruise control is set. When the ignition is on, the fuel gage shows how much fuel the vehicle has remaining in the fuel tank. The light goes out when the cruise control is turned off. See Cruise Control on page 4-7 for more information. 4-32 An arrow on the fuel gage indicates the side of the vehicle the fuel door is on. Here are four things that some owners ask about. None of these indicate a problem with the vehicle’s fuel gage: • At the gas station, the gas pump shuts off before the gage reads full. • It takes a little more or less fuel to ﬁll up than the gage indicated. For example, the gage may have indicated the tank was half full, but it actually took a little more or less than half the tank’s capacity to ﬁll the tank. • The gage moves a little while turning a corner or speeding up. • The gage does not go back to empty when the ignition is turned off. When the fuel in the fuel tank is low, a LOW FUEL message will display on the Driver Information Center (DIC). See DIC Warnings and Messages on page 4-37 for more information. Driver Information Center (DIC) The Driver Information Center (DIC) displays information such as the trip odometer, personalization features, and warning messages. The DIC display is located on the instrument panel cluster. DIC Operation and Displays The Driver Information Center (DIC) comes on when the ignition is on. If a problem is detected, a warning message appears on the display. Pressing and releasing the trip odometer reset stem on the DIC acknowledges some current warnings or service messages. Some messages only clear after the required action has been taken. The DIC has different menu items which can be accessed by pressing the trip odometer reset stem on the DIC. This includes trip information, such as the odometer and trip odometer, engine oil life reset, and personalization features that are explained in the following information. The DIC trip odometer reset stem is located on the instrument panel cluster next to the DIC display. 4-33 Trip Information Odometer The odometer is automatically displayed on the DIC when you start the vehicle. The odometer shows the total distance the vehicle has been driven in either miles for the United States or kilometers for Canada. Trip Odometer Press and release the reset stem until TRIP appears on the DIC display. The trip odometer shows the current distance traveled since the last reset of the trip odometer in either miles for the United States or kilometers for Canada. To reset the trip odometer, press and hold the reset stem until the display returns to zero. Engine Oil Life System With the engine off, turn the key to ON/RUN and then press the reset stem until OIL LIFE RESET appears — alternating between OIL LIFE and RESET — on the DIC display. The CHANGE OIL message alerts you to change the oil on a schedule consistent with your driving conditions. Always reset the OIL LIFE message after an oil change. To reset the message, see Engine Oil Life System on page 6-18. 4-34 In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Engine Oil on page 6-15 and Scheduled Maintenance on page 7-3 for more information. Personalization Features Language This feature allows you to choose the language in which the DIC display shows information. To set your choice for this feature: 1. With the engine off, turn the key to ON/RUN, but do not start the engine. 2. Close all doors so the DOORS message does not display in the DIC. 3. Momentarily press and release the reset stem until the current language is displayed: English (default), Spanish, or French. 4. To select a different language, press and hold the reset stem until the next language appears. 5. Repeat Step 4 until the desired language is displayed. Once the desired language is shown on the DIC display, the language is set. 6. To exit the language selection, momentarily press and release the reset stem. All DIC messages will now display in the language selected. Automatic Door Locks This feature allows you to program the door locks to a preferred setting. To set your choice for this feature: 1. With the engine off, turn the key to LOCK/OFF. Do not remove the key from the ignition. 2. Press and hold the power door lock button until the DIC display shows the current door lock mode. 3. To view the next available mode, press and hold the reset stem until the mode appears. Release the reset stem and press and hold again to view the next mode. 4. Once the desired mode is shown on the DIC display, brieﬂy press the reset stem to set your choice. The DIC display then clears. The following are the available modes: Lock 1 (default): On vehicles with an automatic transmission, this mode locks all of the doors when the vehicle is shifted out of P (Park) and unlocks all of the doors when the vehicle is shifted into P (Park). On vehicles with a manual transmission, this mode locks all of the doors when the vehicle speed is greater than 15 mph (24 km/h) and unlocks all of the doors when the key is removed from the ignition. Lock 2: On vehicles with an automatic transmission, this mode locks all of the doors when the vehicle is shifted out of P (Park) and unlocks the driver’s door when the vehicle is shifted into P (Park). On vehicles with a manual transmission, this mode locks all of the doors when the vehicle speed is greater than 15 mph (24 km/h) and unlocks the driver’s door when the key is removed from the ignition. Lock 3: On vehicles with an automatic transmission, this mode locks all of the doors when the vehicle is shifted out of P (Park). The doors will not automatically unlock. On vehicles with a manual transmission, this mode locks all of the doors when the vehicle speed is greater than 15 mph (24 km/h). The doors will not automatically unlock. 4-35 Remote Keyless Entry (RKE) Feedback This feature allows you to program the Remote Keyless Entry (RKE) feedback to a preferred setting. To set your choice for this feature: 1. With the engine off, turn the key to LOCK/OFF. Do not remove the key from the ignition. 2. Press and hold the lock and unlock buttons on the RKE transmitter at the same time. Hold both buttons until the DIC display shows the current RKE feedback mode. 3. To view the next available mode, press and hold the reset stem until the mode appears. Release the reset stem and press and hold again to view the next mode. 4. Once the desired mode is shown on the DIC display, brieﬂy press the reset stem to set your choice. The DIC display then clears. The following are the available modes: RFA 1 (default): This mode ﬂashes the parking lamps when you press the lock or unlock buttons on the RKE transmitter. RFA 2: This mode ﬂashes the parking lamps and sounds the horn when you press the lock button on the RKE transmitter. This mode also ﬂashes the parking lamps when you press the unlock button on the RKE transmitter. RFA 3: This mode ﬂashes the parking lamps and sounds the horn when you press the lock or unlock buttons on the RKE transmitter. RFA 4: This mode disables RKE feedback. There will be no feedback when you press the lock or unlock buttons on the RKE transmitter. 4-36 DIC Warnings and Messages Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. Multiple messages may appear one after another. The messages are displayed for several seconds each. Some messages may not require immediate action, but you should press and release the trip odometer reset stem to acknowledge that you received the messages and to clear them from the display. Each message must be acknowledged individually. Some messages cannot be cleared from the DIC display because they are more urgent. These messages require action before they can be cleared. You should take any messages that appear on the display seriously and remember that clearing the messages only makes the messages disappear, not correct the problem. The following are the possible messages that can be displayed and some information about them. AC (Air Conditioning) OFF This message displays when the engine coolant temperature is too high and the air conditioning in your vehicle needs to be turned off. See Engine Overheating on page 6-35 and Climate Control System on page 4-16 for more information. This message displays along with the ENG HOT message. ABS (Antilock Brake System) FAULT This message displays if there is a problem with the Antilock Brake System (ABS). Check the ABS as soon as possible and have your vehicle serviced by your dealer/ retailer. See Brakes on page 6-39 and Antilock Brake System (ABS) Warning Light on page 4-26 for more information. Press and release the reset stem to acknowledge the message and clear it from the display. 4-37 BRAKES This message displays if there is a problem with the brakes. Check the brakes as soon as possible and have your vehicle serviced by your dealer/retailer. See Brakes on page 6-39 and Brake System Warning Light on page 4-25 for more information. Press and release the reset stem to acknowledge the message and clear it from the display. CHANGE OIL This message displays when the oil needs to be changed. Check the oil in your vehicle as soon as possible and have your vehicle serviced by your dealer/retailer. See Engine Oil on page 6-15 and Scheduled Maintenance on page 7-3 for more information. Press and release the reset stem to acknowledge the message and clear it from the display. DOORS This message displays when one or more of the doors is ajar. Check all the doors on your vehicle to make sure they are closed. The message clears from the display after all of the doors are closed. ENG (Engine) HOT This message displays when the engine coolant temperature is hot. Check the engine coolant temperature gage. See Engine Coolant Temperature Gage on page 4-27. Have your vehicle serviced by your dealer/retailer as soon as possible if you suspect the engine is overheating. See Engine Overheating on page 6-35 for more information. FLUID This message displays if the brake ﬂuid is low. Check the brake ﬂuid as soon as possible and have your vehicle serviced by your dealer/retailer. See Brakes on page 6-39 for more information. Press and release the reset stem to acknowledge the message and clear it from the display. 4-38 FUEL CAP This message displays if the vehicle’s fuel cap is either off or loose. Pull over as soon as possible and check to see if the fuel cap is secure. You may also see the check engine light on the instrument panel cluster. If the check engine light does come on when the fuel cap was loose, it may take a few driving trips before the light turns off. See Malfunction Indicator Lamp on page 4-28 for more information if the light still remains on. Press and release the reset stem to acknowledge the message and clear it from the display. LOW FUEL This message displays if the level of fuel in the vehicle is low. Also check the fuel gage. See Fuel Gage on page 4-32 for more information. Reﬁll the fuel tank as soon as possible. LOW TIRE This message displays if a low tire pressure is detected in any of the vehicle’s tires. Press and release the reset stem to acknowledge the message and clear it from the display. The message appears at each ignition cycle until the tires are inﬂated to the correct inﬂation pressure. See Tires on page 6-57 and Inﬂation - Tire Pressure on page 6-64 for more information on tires and the correct inﬂation pressures. OIL This message displays when the oil pressure is low. See Oil Pressure Light on page 4-31 and Engine Oil on page 6-15 for more information. PARK BRK (Brake) This message displays when the parking brake is set. See Parking Brake on page 3-30 and Brake System Warning Light on page 4-25 for more information. The message clears from the display after the parking brake is released or by pressing and releasing the reset stem. 4-39 SERV (Service) TPM (Tire Pressure Monitor) This message displays if a part on the Tire Pressure Monitor System (TPMS) is not working properly. The tire pressure light also ﬂashes and then remains on during the same ignition cycle. See Tire Pressure Light on page 4-28. Several conditions may cause this message to appear. See Tire Pressure Monitor Operation on page 6-67 for more information. If the warning comes on and stays on, there may be a problem with the TPMS. See your dealer/retailer. SERV (Service) VEH (Vehicle) This message displays if your vehicle needs service. Have your vehicle serviced by your dealer/retailer as soon as possible. REDUCED POWER This message displays when the vehicle’s engine power is reduced. Reduced engine power can affect the vehicle’s ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer/retailer for service as soon as possible. Press and release the reset stem to acknowledge the message and clear it from the display. SERV (Service) 4WD (Four-Wheel Drive) This message displays when there is a problem with the transfer case control system. Check the transfer case on your vehicle and have it serviced by your dealer/retailer. See Four-Wheel Drive on page 3-25 for more information about the transfer case. Press and release the reset stem to acknowledge the message and clear it from the display. 4-40 SERVICE CHARG (Charge) SYS (System) This message displays if there is a problem with the battery charging system. Under certain conditions, the battery warning light may also turn on in the instrument panel cluster. See Charging System Light on page 4-24. The battery will not be charging at an optimal rate and the vehicle will lose the ability to enter the fuel economy mode. The vehicle is safe to drive, however have the electrical system checked by your dealer/retailer. Press and release the reset stem to acknowledge the message and clear it from the display. SERVICE STAB (Stability) SYS (System) This message displays if there is a problem with the StabiliTrak system. Have your vehicle serviced by your dealer/retailer. See StabiliTrak® System on page 5-6 for more information. STAB (Stability) SYS (System) OFF This message displays when the StabiliTrak system is turned off. See StabiliTrak® System on page 5-6 for more information. TRAC (Traction) OFF This message displays when the Traction Control System (TCS) is turned off by pressing the StabiliTrak button. See StabiliTrak® System on page 5-6 for more information. TRACTION FAULT This message will display if there is a problem with the TCS. Have your vehicle serviced by your dealer/retailer. See Traction Control System (TCS) on page 5-8 for more information. Press and release the reset stem to acknowledge the message and clear it from the display. TURN SIGNAL This message displays when the turn signal is on for about 0.75 miles (1.2 km) of travel. Press and release the reset stem to acknowledge the message and clear it from the display. 4-41 Notice: Contact your dealer/retailer before adding any equipment. Adding audio or communication equipment could interfere with the operation of the vehicle’s engine, radio, or other systems, and could damage them. Follow federal rules covering mobile radio and telephone equipment. Notice: The chime signals related to safety belts, parking brake, and other functions of your vehicle operate through the radio/entertainment system. If that equipment is replaced or additional equipment is added to your vehicle, the chimes may not work. Make sure that replacement or additional equipment is compatible with your vehicle before installing it. See Accessories and Modiﬁcations on page 6-3. The vehicle has Retained Accessory Power (RAP). With RAP, the audio system can be played even after the ignition is turned off. See Retained Accessory Power (RAP) on page 3-18 for more information. Audio System(s) Determine which radio the vehicle has and read the following pages to become familiar with its features. { WARNING: Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to entertainment tasks while driving. This system provides access to many audio and non audio listings. To minimize taking your eyes off the road while driving, do the following while the vehicle is parked: • Become familiar with the operation and controls of the audio system. • Set up the tone, speaker adjustments, and preset radio stations. For more information, see Defensive Driving on page 5-2. 4-42 Radio(s) Setting the Clock AM-FM Radio Press and hold HR until the correct hour displays. Press and hold MIN until the correct minute displays. There is an initial two-second delay before the clock goes into time-set mode. To display the time with the ignition off, press RCL, HR, or MIN. Radio with CD (MP3/WMA) Press and hold the HR button until the correct hour displays. Press and hold the MIN button until the correct minute displays. The time can be set with the ignition on or off. To synchronize the time with an FM station broadcasting Radio Data System (RDS) information, press and hold the HR and MIN buttons at the same time until RDS TIME displays. To accept this time, press and hold the HR and MIN buttons, at the same time, for another two seconds. If the time is not available from the station, NO UPDAT (update) displays. RDS time is broadcast once a minute. After tuning to an RDS broadcast station, it could take a few minutes for the time to update. AM-FM Radio 4-43 With RDS, the radio can do the following: • Seek to stations broadcasting the selected type of programming. • Receive announcements concerning local and national emergencies. • Display messages from radio stations. • Seek to stations with traffic announcements. This system relies upon receiving speciﬁc information from these stations and only works when the information is available. In rare cases, a radio station could broadcast incorrect information that causes the radio features to work improperly. If this happens, contact the radio station. While the radio is tuned to an RDS station, the station name or call letters display instead of the frequency. RDS stations can also provide the time of day, a program type (PTY) for current programming, and the name of the program being broadcast. Radio with CD (MP3/WMA) Radio Data System (RDS) The audio system has a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information. 4-44 Playing the Radio PWR (Power): Press to turn the system on and off. o p VOL/VOLUME: Turn to increase or to decrease the volume. RCL (Recall) (AM-FM Radio): Press to switch the display between the radio station frequency, band, and the time. When the ignition is off, press to display the time. DISPL (Display) (Radio with CD): When the ignition is turned off, press to display the time. For RDS, press the DISPL knob to change what displays while using RDS. The display options are station name, RDS station frequency, PTY (program type), and the name of the program (if available). For XM™ (if equipped), press the DISPL knob while in XM mode to retrieve four different categories of information related to the current song or channel: Artist, Song Title, Category or PTY, Channel Number/ Channel Name. To change the default on the display, press the DISPL knob until you see the desired display, then press and hold this knob for two seconds. The radio produces one beep. The selected display is now the default. AUTO VOL (Automatic Volume): Automatic volume automatically adjusts the audio system to make up for road and wind noise while driving. Set the volume at the desired level. Depending on the radio and displays, press to select MIN, MED, MAX AUTO VOL, or LOW, MEDIUM, and HIGH. AVOL displays. Each higher setting allows for more volume compensation at faster vehicle speeds. Then while driving, automatic volume increases the volume, as necessary, to overcome noise at any speed. The volume level should always sound the same while driving. For the Radio with CD, NONE displays if the radio cannot determine the vehicle speed. To turn automatic volume off, press until OFF or AUTO VOL OFF displays. 4-45 q SCAN r: Press and hold for more than two seconds. SCAN or SCN displays and the radio produces one beep. The radio goes to a station, plays for a few seconds, then goes to the next station. Press either SCAN arrow again, to stop scanning presets. To scan preset stations, press and hold either SCAN arrow for more than four seconds. PSCN or PSC displays and the radio produces one beep or depending on the radio, two beeps. The radio goes to a preset station, plays for a few seconds, then goes to the next preset station. Press either SCAN arrow again, to stop scanning presets. The radio only scans stations with a strong signal that are in the selected band. Finding a Station AM FM (AM-FM Radio): Press to switch between FM1, FM2, or AM. The selection displays. BAND: Press to switch between FM1, FM2, AM, or XM1 or XM2 (if equipped). The selection displays. q r TUNE: Turn to select radio stations. q SEEK r: Press to go to the previous or to the next station and stay there. To scan stations, press and hold either arrow for two seconds until a beep sounds. The radio goes to a station, plays for a few seconds, then goes to the next station. Press either arrow again to stop scanning. To scan preset stations, press and hold either arrow for more than four seconds until two beeps sound. The radio goes to the ﬁrst preset station stored on the pushbuttons, plays for a few seconds, then goes to the next preset station. Press either arrow again to stop scanning presets. 4-46 Setting Preset Stations If the radio does not have XM, up to 18 stations (six FM1, six FM2, and six AM) can be programmed on the six numbered pushbuttons. If the radio has XM, up to 30 stations (six FM1, six FM2, six AM, six XM1 and six XM2) can be programmed on the six numbered pushbuttons. To program either radio: 1. Turn the radio on. 2. Press BAND to select FM1, FM2, AM, or XM1 or XM2 (if equipped). • For the AM-FM Radio, press AM FM to select FM1, FM2, or AM. 3. Tune in the desired station. 4. Press and hold one of the six numbered pushbuttons until the radio beeps once. When that numbered pushbutton is pressed again, the station that was stored, returns. 5. Repeat the steps for each pushbutton. Setting the Tone (Bass/Treble) AUDIO: Push and release until BASS/TREB, or depending on the radio, BASS, MID, or TREB displays. Turn to increase or to decrease. The tone display shows the bass or the treble level. If a station is weak or has static, decrease the treble. • For the AM-FM Radio, press and hold the w x arrows to increase or to decrease the tone. To adjust the bass/treble or bass/midrange/treble to the middle position, press and hold the AUDIO knob. The radio produces one beep and adjusts the display level to the middle position. • For the AM-FM Radio, adjust bass or treble to the middle position, select BAS (bass) or TRE (treble). Then press and hold for more than two seconds until a beep sounds. B (balance) and a zero or T (treble) and a zero displays. 4-47 To adjust all tone and speaker controls to the middle position, push and hold the AUDIO knob when no tone or speaker control displays. ALL CENTERED displays and a beep sounds. • For the AM-FM Radio, adjust both tone controls and both speaker controls to the middle position, ﬁrst exit out of audio mode by pressing another button, causing the radio to perform that function or wait ﬁve seconds for the display to return to time of day. Then press and hold for more than two seconds until a beep sounds. CEN (center) displays. AUTO EQ (Automatic Equalization): Press to select customized equalization settings designed for country/western, jazz, talk, pop, rock, and classical. To return to the manual mode, press the AUTO EQ button until CUSTOM displays. Then manually adjust the bass/treble, or bass/midrange/treble by using the AUDIO knob. Adjusting the Speakers (Balance/Fade) AUDIO: To adjust the balance between the right and the left speakers, push and release until BAL (balance) displays. Turn to move the sound toward the right or the left speakers. • For the AM-FM Radio, press and hold the w x arrows to move the sound toward the right or the left speakers. To adjust the fade between the front and the rear speakers, push and release the AUDIO knob until FADE or depending on the radio, FAD displays. Turn the knob to move the sound toward the front or the rear speakers. • For the AM-FM Radio, press and hold the w x arrows to move the sound toward the right or the left speakers. 4-48 To adjust the balance or the fade to the middle position, push the AUDIO knob to select BAL or FADE/FAD, then push it again and hold it until one beep sounds. • For the AM-FM Radio, adjust balance or fade to the middle position by selecting BAL or FAD. Press and hold AUDIO for more than two seconds until a beep sounds. B (balance) and a zero or F (fade) and a zero displays. To adjust all tone and speaker controls to the middle position, push and hold the AUDIO knob when no tone or speaker control is displayed. ALL CENTERED displays and a beep sounds. • For the AM-FM Radio, adjust both tone controls and both speaker controls to the middle position by exiting out of audio mode. To do this, press any button for the radio to perform that function or wait ﬁve seconds for the display to return to time of day. Then press and hold AUDIO for more than two seconds until a beep sounds. CEN (center) displays. Fade might not be available if the vehicle is a regular cab model. Finding a Program Type (PTY) Station (RDS and XM) To select and ﬁnd a desired PTY perform the following: 1. Press the P-TYPE to activate program type select mode. P-TYPE or TYPE and a PTY displays. 2. Turn the P-TYPE knob again, to select a PTY. 3. Once the desired PTY displays, press the SEEK / TYPE button to select and to take you to the PTY’s ﬁrst station. 4. To go to another station within that PTY by pressing the SEEK / TYPE button twice to display the PTY and then go to another station. To cancel the seek, press the SEEK / TYPE button. This also exits the program type seek mode and returns to the last tuned station. If both PTY and TRAF (traffic) are on, the radio searches for stations with the selected PTY and traffic announcements. 4-49 If the radio cannot ﬁnd the desired program type, NONE displays and the radio returns to the last tuned station. SCAN: To scan PTYs, press and hold the SEEK / SCAN until a beep sounds. The radio goes to a station, plays for a few seconds, then goes to the next station. BAND (Alternate Frequency): Alternate frequency lets the radio switch to a stronger station with the same program type. To turn alternate frequency on, press and hold BAND for two seconds. AF ON displays. The radio could switch to stations with a stronger frequency. To turn alternate frequency off, press and hold BAND again for two seconds. AF OFF displays. The radio does not switch to other stations. This function does not apply for XM Satellite Radio Service. Setting Preset PTYs (RDS) Only For the Radio with CD player, the six pushbuttons have factory PTY presets. Up to 12 PTYs (six FM1 and six FM2), can be programmed on the numbered pushbuttons. To program PTYs: 1. Press BAND to select FM1 or FM2. 2. Turn the P-TYPE knob to activate program type select mode. TYPE and the last selected PTY displays. 3. Turn the P-TYPE knob to select a PTY. 4. Press and hold one of the six numbered pushbuttons until a beep sounds. When that numbered pushbutton is pressed, the PTY that was set, returns. 5. Repeat the steps for each pushbutton. 4-50 RDS Messages ALERT!: For the Radio with CD, the Alert feature warns of local or national emergencies. When an alert announcement comes on the current radio station, ALERT! displays. The announcement is heard, even if the volume is low or a CD is playing. If a CD is playing, play stops during the announcement. Alert announcements cannot be turned off. ALERT! is not affected by tests of the emergency broadcast system. This feature is not supported by all RDS stations. INFO (Information): If the current station has a message, the information symbol or INFO displays. Press this button to see the message. The message can display the artist, song title, call in phone numbers, etc. If the entire message is not displayed, parts of the message displays every three seconds. To scroll through the message, press and release the INFO button. A new group of words display after every press of this button. Once the complete message has displayed, the information symbol or INFO disappears from the display until another new message is received. The last message can be displayed by pressing the INFO button. The last message stays on the display until a new message is received or the radio is tuned to a different station. When a message is not available from a station, NO INFO displays. TRAF (Traffic): For the Radio with CD, if TRAF displays, the tuned station broadcasts traffic announcements. When a traffic announcement is broadcast on this station you will hear it. If the station does not broadcast traffic announcements, press the TRAF button and the radio seeks to a station

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2010 GMC Canyon Owners Manual