2006 Ford Freestar Owners Manual

The dome lamp will illuminate whenever a front door is opened. If either front door has been opened from the outside, the lamp will remain on for 20 seconds after the door is shut. If any other door has been opened from the inside, the lamp will shut off immediately after the door is closed.

Cargo lamp The cargo lamp will stay on if the control is moved to the driver side position. When the control is in the middle position, the lamp will only come on when a door is opened. If the control is moved to the passenger’s side position, the lamp will not come on at all. With the ignition key in the ACCESSORY or ON position, the rear cargo lamp can be turned ON or OFF by sliding the control.

BULB REPLACEMENT

Headlamp Condensation The headlamps are vented to equalize pressure. When moist air enters the headlamp(s) through the vents, there is a possibility that condensation can occur. This condensation is normal and will clear within 45 minutes of headlamp operation.

Replacing exterior bulbs Check the operation of all the bulbs frequently.

Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to ensure lamp performance, light brightness and pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time.

50

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Lights

Function Front park/turn lamps Front sidemarker lamp Cornering lamps Auxiliary parking lamps Headlamps Rear license plate lamps High-mount brake lamp Rear tail/stop/turn lamps Backup lamps Dome lamp (front row) Cargo lamp Map lamps Dome lamp (third row) Map lamp (overhead console) Stepwell lamp Front seat footwell Front door mounted courtesy lamp Visor vanity lamp - Slide on Rail system (SOR) All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your authorized dealer.

Trade Number 3457AK (amber) 904NA (amber) 3156K 912
H13
W5WL LED (see dealer) 4157K or 3157K 3156K 10W sofitte 10W sofitte H6W 10W sofitte 906
T-562
194
168

37

Replacing headlamp bulbs To remove the headlamp bulb: 1. Make sure headlamp switch is in the OFF position, then open the hood.

51

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Lights

2. Remove the two retainer pins to release the headlamp assembly and pull headlamp assembly forward to expose the back of the bulb.

3. Disconnect the electrical connector from the bulb by pulling rearward and unlock the bulb by rotating it counterclockwise.

Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.

Install the new bulb(s) in reverse order. Replacing front parking/turn/sidemarker signal bulbs 1. Make sure the headlamp switch is in the OFF position and open the hood. 2. Remove the two headlamp retaining pins to release the headlamp assembly, then pull the headlamp assembly forward to expose the bulb socket.

52

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Lights

53

3. To remove the side marker bulb, turn the bulb socket counterclockwise, and pull the bulb straight out of the socket.

4. To remove the parking/turn bulb, turn the socket on the bottom of the headlamp assembly counterclockwise and pull the bulb straight out of the socket.

Install the new bulb(s) in reverse order. Replacing tail lamp/backup/turn lamp bulbs 1. Make sure the headlamp switch is in the OFF position and open the liftgate to expose the tail lamp assembly, then remove the retaining screws for the lamp assembly. 2. Carefully remove the lamp assembly. 3. Rotate bulb socket counterclockwise and remove from lamp assembly. 4. Pull bulb straight out of socket and push in new bulb. Install the new bulb(s) in reverse order. Replacing high-mount brakelamp bulbs For bulb replacement, see your authorized dealer.

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Lights

Replacing license plate lamp bulb The license plate bulbs are located in the license plate housing assembly on the liftgate. To change the license plate bulbs: 1. Make sure the headlamp switch is in the OFF position. 2. Remove the license lamp screw from the assembly. 3. Pull the lamp down and twist the bulb socket counterclockwise. Remove the bulb socket from the lamp. 4. Pull out the old bulb and push in the new bulb. 5. Install the bulb socket in the lamp assembly by turning it clockwise. 6. Install the lamp assembly and secure it with the retaining screw.

Replacing supplemental park lamp or cornering lamp bulbs (if equipped) The supplemental park or cornering lamp is located on the front fascia, below the bumper and headlamps. 1. Make sure the park lamp switch is in the OFF position and then remove the bulb socket from the supplemental parking lamp by turning counterclockwise. 2. Disconnect the electrical connector.

Install the new bulb in reverse order.

54

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers.

Windshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick push and hold: the wipers

will swipe three times with washer fluid.

• a long push and hold: the wipers and washer fluid will be activated for

up to ten seconds.

Rear window wiper/washer controls For rear wiper operation, rotate the rear window wiper and washer control to the desired position. Select: INT 2 — One second interval rear wiper. INT 1 — Ten second interval rear wiper. OFF — Rear wiper and washer off. For rear wash cycle, rotate (and hold as desired) the rear wiper/washer control to either From either position, the control will automatically return to the INT2 or OFF position.

position.

55

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

TILT STEERING WHEEL To adjust the steering wheel: 1. Pull and hold the steering wheel release control toward you. 2. Move the steering wheel up or down until you find the desired location. 3. Release the steering wheel release control. This will lock the steering wheel in position.

Never adjust the steering wheel when the vehicle is moving.

ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on the visor mirror lamp.

Slide on rod feature Rotate the visor towards the side window and extend it rearward for additional sunlight coverage. Note: To stow the visor back into the headliner, visor must be retracted before moving it back towards the windshield.

OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according to your option package.

56

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Conversation mirror The conversation mirror allows the driver to view the rear seating area.

This does not replace the rear view mirror.

Electronic compass/temperature display (if equipped) The overhead console may have an electronic compass and outside air temperature display. The compass heading and outside air temperature are displayed together - side by side. The display, as a whole, can be turned on or off by pressing the momentary push-button on the overhead console. When the vehicle is turned off, the electronics display will remember the last display state. Outside air temperature The temperature can be displayed in either Centigrade or Fahrenheit. This is controlled via the Message Center. Please refer to the Message Center in this chapter to change from English to metric. The ignition key must be in the ON or ACCESSORY position. If the outside temperature falls below 3°C (38°F), the display will alternate from “ICE” to the outside temperature at a two second rate for one minute. Compass The vehicle heading is displayed as one of N, NE, E, SE, S, SW, W and NW. The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in or on the vehicle may also affect compass accuracy. Adjustments may need to be made to the zone and calibration of the compass.

57

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Zone variation mode 1. Determine which magnetic zone you are in by referring to the zone map. 2. Turn the ignition to the ON position.

23

15

14
13
12

7 8 9 1011

3. Press and hold the momentary push-button for approximately 4
seconds, until VAR is displayed, then release it. (Pressing the momentary push-button for 8
seconds de-calibrates the compass—see Compass Calibration Mode). 4. Press the button to increment the VAR number to the desired VAR number. Wait 5 seconds without button activity and the compass will return to the heading mode. Note: If there is no button activity for 5 seconds, the compass writes the displayed zone VAR number to memory and exits Zone Variation Mode Compass calibration mode 1. Press the momentary push button and hold it for more than 8 seconds. After 8 seconds, CAL is displayed, then release it. Note: After button release CAL will be displayed with a heading. The compass is now de-calibrated and enters the Initial AutoCal Mode. 2. Drive the vehicle in a tight circle in a magnetically clean area such as an open parking lot. Drive at a rate not faster than 15 seconds per circle 5 mph (8km/h).

58

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Note: Look for a parking lot away from buildings, light posts, manhole covers, sewer and drainage grates and other metallic objects. Some magnetic objects may be hidden underground. Look for signs of underground utilities, water mains or other industrial structures. The parking lot should be level and have a smooth surface. Blacktop is preferred over cement as a cement surface often contains iron reinforcing bars or metallic mesh that could interfere with the calibration process. • The CAL indicator will turn off when the calibration process is

complete, leaving the compass heading on the display.

Note: This process normally takes about 11⁄2 circles but may take longer if magnetic noise is present or if the circles are driven too fast.

SLIDING DOOR OPERATION Manual door operation If equipped with a Power Sliding Door (PSD), turn the Power Door Lockout control on the overhead console to the OFF position. Refer to the Disabling power operation of the PSD section in this chapter for more information. Note: Before unlatching the left side door, verify that the fuel fill door is closed. The left hand door will not open if the fuel door is open. Slide the door carefully in a controlled manner to the full open position. At the end of travel, firmly push the door against the bump stop to engage the hold open mechanism to restrain the door. When operating the door on a gradient, special care should be taken to manually control the opening and closing speed of the door.

If the door is allowed to slide open or closed unrestrained, personal injury or damage to the door could result.

When closing the sliding door, keep the head, hands and other body parts of vehicle occupants out of the path of the closing door. Slide the door closed in a careful, controlled manner.

When closing the sliding doors, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the sliding door openings. Injury could result if body parts are caught or pinched in an uncontrolled sliding door.

59

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Manual door operation when vehicle is stopped or parked on a downhill grade In some cases it may be necessary to have someone hold the door while rear seat passengers are entering or exiting the vehicle. The hold open mechanism will restrain the door open when the vehicle is parked on moderate downhill grades. On more severe grades, the operator should ensure that the open door is stable and secure against the stop, before allowing passengers to enter or exit the vehicle or before loading/unloading cargo.

Do not operate vehicle with the door in the open position. Abrupt vehicle acceleration or deceleration could cause the door to move suddenly and could result in personal injury or damage to the door.

If the vehicle is parked on a downhill grade, the door could slam shut and could result in injury or damage to the door. Ensure

that the open door is secure against the stop before allowing passengers to enter or exit the vehicle.

Power Sliding Door (PSD) (if equipped) With this option, you can open and close the sliding door(s) with the following controls inside your vehicle. • overhead console button • remote entry transmitter button • second row passenger control switch • inside and outside release handle Opening and closing the PSD The PSD will operate without the key in the ignition. The transaxle must be in PARK to open the PSD, when the key is in the ignition and turned to the ON position.

60

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

The sliding door must be unlocked for the PSD to power open from the rear trim switches and the inside or outside PSD handles. The fuel filler door must be closed in order to avoid damage to it when the left sliding door is opened. The Power Door Lockout Control is located in the overhead console. With the control in the OFF position, power operation is disabled from both PSD handles and from both second row passenger switches. The overhead console switch and remote entry transmitter will operate the power doors regardless of the position of the lockout switch.

When opening or closing the sliding doors, you should verify they are free of obstructions and ensure that children and/or

pets are not in the proximity of the sliding door openings. Injury could result if body parts are caught or pinched in an uncontrolled sliding door.

To power open or close the PSD from the Overhead console: Push and release the overhead console right or left hand control. Pressing this control will also simultaneously unlock all doors. To power open or close the PSD from the second row passenger control switch: • Ensure that the PSD is unlocked, using the remote entry transmitter or power door unlock. Refer to Remote Entry System in the Locks and security chapter.

• Push and release the right or left hand second row passenger control.

The control(s) are located on the trim panel in front of the sliding door.

To power open the PSD with the inside or outside release handle: • Ensure that the PSD is unlocked, using the remote entry transmitter or power door unlock. Refer to Remote Entry System in the Locks and security chapter.

61

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls • Manually pull the inside or outside sliding door handle to engage the power assist feature. Release the handle as soon as the PSD begins to power open.

To power close the PSD with the inside or outside release handle: • Manually pull the door about 6 inches in the desired direction of

travel. The power door assist will take over and complete the open or close operation.

Pressing any of the switches, overhead console, second row passenger, or remote entry transmitter while the door is moving will cause the door to either reverse direction or stop depending on the position and direction of movement of the door. To power open or close the PSD with the remote entry transmitter: Refer to the Remote entry system section in this chapter. Operating the transmitter will also simultaneously unlock the doors. Disabling PSD power operation Pressing the Power Door Lockout Control to the OFF position prevents power operation of the PSD using the rear seat control(s), inside or outside handle or by manually moving the door. With the PSD rear controls disabled, the door(s) can be opened manually with the inside or outside handles. With the Power Door Lockout control in the OFF position, the overhead console right and left hand controls and the Remote Entry System remain functional. Disabling the PSD may be desirable to prevent power operation of the door by rear seat passengers or if manual operation of the door is desired or necessary when the vehicle is stopped or parked on a steep downhill grade. Refer to the Manual operation of the sliding door section in this chapter for more information. With the child safety lock engaged, the inside handle operation will always be disabled regardless of the position of the Power Door Lockout control. Refer to the Sliding door child safety lock section in this chapter for more information. The trim mounted rear seat control and the outside handle remain functional for power operation. Safety/Obstructions If anything obstructs the Power Sliding Door while it is power closing or opening, the door will automatically reverse or stop depending on the position of the door, provided it meets sufficient resistance.

62

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Resetting the PSD The power sliding door may operate incorrectly or not at all because of the following conditions: • a low voltage or dead battery • the door is left opened for more than 6 hours • the battery is disconnected • the PSD Passenger compartment fuse panel fuse (fuse #11) is removed or blown. Refer to Fuses and relays in the Roadside Emergencies chapter.

If any of the above conditions has occurred, perform the following steps to reset the PSD so that electronics can relearn the open and closed positions: 1. Check to see if PSD is securely closed. 2. Make sure the gearshift is in (P) Park. 3. Push the PSD control on the overhead console to open the door. 4. Wait five (5) seconds and close the door by pressing the PSD control on the overhead console. 5. Wait five (5) seconds and repeat Steps 3 and 4 then go on to Step 6. 6. Repeat Steps 3–5 for opposite door. If the door still does not operate correctly: 7. Ensure the ignition is in the OFF position 8. Remove the PSD fuse (fuse #11) from the passenger fuse panel and leave it out for thirty (30) seconds. Refer to the chapter on Fuses and Relays. Refer to Fuses and relays in the Roadside emergencies chapter. 9. Reinstall the fuse and wait ten (10) seconds. 10. Repeat Steps 1–6 above. If the door still does not operate correctly, see your dealer for service. Sliding Door Child Safety Lock Your vehicle is equipped with a sliding door child safety lock that helps prevent passengers from operating the sliding door by using the inside door handle, refer to the Childproof door locks in the Locks and security chapter.

63

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

To open the sliding door when the child safety lock is on: • Unlock the sliding door and open the door from the outside. • Press the right or left hand

control on the overhead console or the remote to open the door.

• The second row passenger switch will still be functional to open the door. To prevent the second row passenger from operating the PSD, turn the Power Door Lockout control to the OFF position.

INSTRUMENT PANEL STORAGE COMPARTMENT The storage compartment may be used to secure sunglasses or similar sized objects. Press the control to open the storage compartment.

CLOCK (IF EQUIPPED) Press the right (+) control to move the time display forwards. Press the left (-) control to move the time display backwards.

AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty.

64

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Do not use the power point for operating the cigarette lighter element (if equipped). To prevent the fuse from being blown, do not use the power point(s) over the vehicle capacity of 12 VDC/180W. To prevent the battery from being discharged, do not use the power point longer than necessary when the engine is not running. Always keep the power point caps closed when not being used. There are up to three auxiliary power points in the following locations: • Located on the instrument panel.

• Located next to the second row

seat.

• Located on the right trim panel in

the rear cargo area.

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

65

Driver Controls

Cigar/Cigarette lighter (if equipped) Do not plug optional electrical accessories into the cigarette lighter socket. Do not hold the lighter in with your hand while it is heating, this will damage the lighter element and socket. The lighter will be released from its heating position when it is ready to be used. Improper use of the lighter can cause damage not covered by your warranty.

POWER WINDOWS

Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure

themselves.

When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in

the proximity of the window openings.

AUTO

Press and pull the window switches to open and close windows. • Push down (to the first detent) • Pull up (to the first detent) and

and hold the switch to open.

hold the switch to close.

One touch down Allows the driver’s window to open fully without holding the control down. Push the switch completely down to the second detent and release quickly. The window will open fully. Momentarily press the switch to any position to stop the window operation.

66

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Accessory delay With accessory delay, the window switches and radio may be used for up to ten minutes after the ignition switch is turned to the OFF position or until any door or trunk is opened. Power vent windows

Do not leave children unattended in the vehicle and do not let children play with the power vent windows. They may seriously

injure themselves.

When closing the power vent windows, you should verify they are free of obstructions and ensure that children and/or pets are

not in the proximity of the window openings.

The power vent windows are operated by a single switch located on the instrument panel. Press and hold the bottom of the switch to open or the top of the switch to close both vent windows. A sound will be heard when opening and closing the vent windows. This is a normal noise that informs you the windows are operating. AUTOMATIC DIMMING INSIDE REAR VIEW MIRROR (IF EQUIPPED) Your vehicle may be equipped with an inside rear view mirror with an auto-dimming function. The electronic day/night mirror will change from the normal (high reflective) state to the non-glare (darkened) state when bright lights (glare) reach the mirror. When the mirror detects bright light from behind the vehicle, it will automatically adjust (darken) to minimize glare. The mirror will automatically return to the normal state whenever the vehicle is placed in R (Reverse) to ensure a bright clear view when backing up. Do not block the sensor on the backside of the inside rear view mirror since this may impair proper mirror performance.

67

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

EXTERIOR MIRRORS

Power side view mirrors To adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place.

(if equipped)

Heated outside mirrors Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors.

Signal indicator mirrors (if equipped) When the turn signal is activated, the appropriate mirror will show a blinking yellow arrow. When the park lamps are on, the blinking arrow will be dimmer. The arrow provides an additional warning to other drivers that your vehicle is about to turn. When the sliding door is open, the indicator in the appropriate mirror will flash indicating people may be entering/exiting the vehicle.

68

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Fold-away mirrors Carefully pull the outside mirrors inwards when driving through a narrow space, like an automatic car wash.

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position. Press and hold the rocker control to adjust accelerator and brake pedal toward you or away from you.

The adjustment allows for approximately 2.8 inches (73 mm) of maximum travel.

Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving.

SPEED CONTROL (IF EQUIPPED) With speed control set, you can maintain a speed of 30 mph (48 km/h) or more without keeping your foot on the accelerator pedal. Speed control does not work at speeds below 30 mph (48 km/h). If your vehicle is equipped with AdvanceTrac娂 system, the speed control will automatically disengage when the road conditions change. When driving conditions permit you can return to speed control by pressing RESUME on the speed control. For more information on the AdvanceTrac娂 system see AdvanceTrac娂 Stability Enhancement System section in the Driving chapter.

Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved.

69

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed.

3. Press the SET + control and release it. 4. Take your foot off the accelerator pedal. 5. The indicator instrument cluster will turn on.

light on the

steep hill.

Note: • Vehicle speed may vary momentarily when driving up and down a • If the vehicle speed increases above the set speed on a downhill, you • If the vehicle speed decreases more than 10 mph (16 km/h) below

may want to apply the brakes to reduce the speed.

your set speed on an uphill, your speed control will disengage.

Disengaging speed control To disengage the speed control: • Depress the brake pedal Disengaging the speed control will not erase previous set speed. Resuming a set speed Press the RESUME control and release it. This will automatically return the vehicle to the previously set speed. The RESUME control will not work if the vehicle speed is not faster than 30 mph (48 km/h).

70

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET + control until you get to the desired speed, then release the control. You can also use the SET + control to operate the Tap-Up function. Press and release this control to increase the vehicle set speed in small amounts by 1 mph (1.6 km/h).

• Use the accelerator pedal to get to the desired speed. When the vehicle reaches that speed press and release the SET + control.

Reducing speed while using speed control There are two ways to reduce a set speed: • Press and hold the CST - control until you get to the desired speed, then release the control. You can also use the CST - control to operate the Tap-Down function. Press and release this control to decrease the vehicle set speed in small amounts by 1 mph (1.6 km/h).

• Depress the brake pedal until the desired vehicle speed is reached, press the SET + control.

71

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal. This will

not erase your vehicle’s previously set speed.

• Press the speed control OFF

control.

Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.

STEERING WHEEL CONTROLS (IF EQUIPPED)

Radio control features • Press MEDIA to select AM, FM1, FM2, TAPE or CD (if equipped).

In Radio mode: • Press SEEK to access the

next/previous strong station.

In Tape mode: • Press SEEK to listen to the next

selection on the tape.

In CD mode: • Press SEEK to listen to the next track on the disc. In any mode: • Press VOL up or down to adjust • Press MUTE to mute the volume.

the volume.

72

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

CENTER CONSOLE (IF EQUIPPED) Your vehicle may be equipped with a utility compartment.

HOMELINK姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink威 Wireless Control System, located on the driver’s visor, provides a convenient way to replace up to three hand-held transmitters with a single built-in device. This feature will learn the radio frequency codes of most transmitters to operate garage doors, entry gate operators, security systems, entry door locks, and home or office lighting.

When programming your HomeLink威 Wireless Control System to a garage door or gate, be sure that people and objects are out of

the way to prevent potential harm or damage.

Do not use the HomeLink威 Wireless Control System with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door which cannot detect an object, signaling the door to stop and reverse, does not meet current U.S. federal safety standards. For more information, contact HomeLink威 at: www.homelink.com or 1–800–355–3515. Retain the original transmitter for use in other vehicles as well as for future programming procedures (i.e. new HomeLink威 equipped vehicle purchase). It is also suggested that upon the sale of the vehicle, the programmed Homelink威 buttons be erased for security purposes, refer to Programming in this section.

Programming Do not program HomeLink威 with the vehicle parked in the garage. Note: Your vehicle may require the ignition switch to be turned to the ACC position for programming and/or operation of the HomeLink威. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink威 for quicker training and accurate transmission of the radio-frequency signal.

73

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

1. Press and hold the two outside buttons releasing only when the indicator light begins to flash after 20 seconds. Do not repeat Step 1
to program additional hand-held transmitters to the remaining two HomeLink威 buttons. This will erase previously programmed hand-held transmitter signals into HomeLink威. 2. Position the end of your hand-held transmitter 1–3 inches (2–8 cm) away from the HomeLink威 button you wish to program (located on your visor) while keeping the indicator light in view. 3. Simultaneously press and hold both the HomeLink威 and hand-held transmitter button. Do not release the buttons until Step 4 has been completed. Some entry gates and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator and Canadian Programming” in this section for Canadian residents. 4. The indicator light will flash slowly and then rapidly. Release both buttons when the indicator light flashes rapidly. (The rapid flashing light indicates acceptance of the hand-held transmitters’ radio frequency signals.) 5. Press and hold the just-trained HomeLink威 button and observe the indicator light. If the light is constant, programming is complete and your device should activate when the HomeLink威 button is pressed and released. Note: To program the remaining two HomeLink威 buttons, begin with Step 2 in the “Programming” section — do not repeat Step 1. Note: If the indicator light blinks rapidly for two seconds and then turns to a continuous red, proceed with Steps 6 through 8 to complete programming of a rolling code equipped device. 6. At the garage door opener receiver (motor-head unit) in the garage, locate the “learn” or “smart” button (usually near where the hanging antenna wire is attached to the unit).

74

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

7. Press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer.) Note: There are 30 seconds in which to initiate Step 8. 8. Return to the vehicle and firmly press, hold for two seconds and release the HomeLink威 button. Repeat the press/hold/release sequence again, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming. HomeLink威 should now activate your rolling code equipped device. To program additional HomeLink威 buttons begin with Step 2 in the “Programming” section. For questions or comments, please contact HomeLink at www.homelink.com or 1–800–355–3515.

Gate Operator & Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink威 to accept the signal from the hand-held transmitter. After completing Steps 1 and 2
outlined in the “Programming” section, replace Step 3 with the following: Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent overheating. • Continue to press and hold the HomeLink威 button (note Step 3 in the

“Programming” section) while you press and release — every two seconds (“cycle”) your hand-held transmitter until the frequency signal has been accepted by the HomeLink威. The indicator light will flash slowly and then rapidly after HomeLink威 accepts the radio frequency signal.

• Proceed with Step 4 in the “Programming” section.

75

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Operating the HomeLink姞 Wireless Control System To operate, simply press and release the appropriate HomeLink威 button. Activation will now occur for the trained product (garage door, gate operator, security system, entry door lock, or home or office lighting etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficulties, contact HomeLink威 at www.homelink.com or 1–800–355–3515.

Erasing HomeLink姞 buttons To erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outer HomeLink威 buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds.

HomeLink威 is now in the train (or learning) mode and can be programmed at any time beginning with Step 2 in the “Programming” section. Reprogramming a single HomeLink姞 button To program a device to HomeLink威 using a HomeLink威 button previously trained, follow these steps: 1. Press and hold the desired HomeLink威 button. Do NOT release the button. 2. The indicator light will begin to flash after 20 seconds. Without releasing the HomeLink威 button, follow Step 2 in the “Programming” section. For questions or comments, contact HomeLink威 at www.homelink.com or 1–800–355–3515.

76

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position, the message center, located on your instrument cluster, displays important vehicle information through a constant monitor of vehicle systems. You may select display features on the message center for a display of status preceded by a brief indicator chime. The system will also notify you of potential vehicle problems with a display of system warnings followed by an indicator chime.

INFO

Selectable features Reset Press this control to select and reset functions shown in the INFO menu and SETUP menu. Info menu This control displays the following options: • Odometer • Distance to Empty • Trip Odometer • Average Fuel Economy • Trip Elapsed Drive Time • Display On/Off (top two lines) Odometer/Trip Odometer Refer to Gauges in the Instrument Cluster chapter. Distance to empty (DTE) Selecting this function from the INFO menu estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling to allow this feature to correctly detect the added fuel.

SETUP

RESET

77

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

service stations

DTE is calculated using a running average fuel economy, which is based on your recent driving history of 500 miles (800 km). This value is not the same as the average fuel economy display. The running average fuel economy is reinitialized to a factory default value if the battery is disconnected. Average Fuel Economy (AFE) Select this function from the INFO menu to display your average fuel economy in 100 miles/gallon or liters/100 km. If you calculate your average fuel economy by dividing gallons of fuel used by 100 miles traveled (kilometers traveled by liters used), your figure may be different than displayed for the following reasons: • your vehicle was not perfectly level during fill-up • differences in the automatic shut-off points on the fuel pumps at • variations in top-off procedure from one fill-up to another • rounding of the displayed values to the nearest 0.1 gallon (liter) 1. Drive the vehicle at least 5 miles (8 km) with the speed control system engaged to display a stabilized average. 2. Record the highway fuel economy for future reference. It is important to press the RESET control after setting the speed control to get accurate highway fuel economy readings. Trip elapsed drive time Select this function from the INFO menu to display your trip elapsed drive time. When selected the display will accumulate when the key is in the ON position. 1. Press the INFO control until the message center display shows the TRIP TIME XX:XX:XX. 2. Hold the RESET control down for two seconds to clear display. Display on/off Select this function from the INFO menu to turn the upper two lines of the message center display OFF or ON.

78

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

INFO

SETUP

RESET

79

Setup menu Press this control for the following displays: • Language • Units (English/Metric) • System Check

Language 1. Select this function from the SETUP menu for the current language to be displayed.

2. Pressing the RESET control cycles the message center through each of the language choices.

3. Press and hold the RESET control for 2 seconds to set the language choice.

Units (English/Metric) 1. Select this function from the SETUP menu for the current units to be displayed. 2. Press the RESET control to change from English to Metric.

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

System check Selecting this function from the SETUP menu causes the message center to cycle through each of the systems being monitored. For each of the monitored systems, the message center will indicate a warning message for three seconds when there is a malfunction. Pressing the RESET control cycles the message center through each of the systems being monitored and will display the following only when there is a malfunction. 1. Oil life in XX% 2. Charging system 3. Washer fluid level 4. Brake fluid level 5. Liftgate status 6. Exterior lamps status 7. Traction Control娂 status 8. Tire pressure monitoring system 9. Fuel level status (hold to reset to relearn) 10. Distance to empty System warnings System warnings alert you to possible problems or malfunctions in your vehicle’s operating systems. In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for 4 seconds. The message center will display the last selected feature if there are no more warning messages. This allows you to use the full functionality of the message center after you acknowledge the warning by pressing the RESET control and clearing the warning message. Warning messages that have been reset are divided into three categories: • They will reappear on the display ten minutes from the reset. • They will not reappear until an ignition OFF-ON cycle has been

completed.

80

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Warning returns after 10 minutes

Status Warning cannot be reset

Warning returns after the ignition key is turned from OFF to ON

• Warning returns upon another event. This acts as a reminder that these warning conditions still exist within the vehicle. Warning display Driver’s door ajar Passenger door ajar Left rear door ajar Right rear door ajar Park brake set Check brake system Liftgate ajar Check left park lamp Check right park lamp Check left headlamp Check right headlamp Check left turn lamp Washer fluid low Check right turn lamp Low fuel level Change oil soon Low tire pressure Tire pressure monitor fault Tire pressure sensor fault Check brake lamps DRIVER’S DOOR AJAR. Displayed when the driver’s door is not completely closed. PASSENGER DOOR AJAR. Displayed when the passenger side door is not completely closed. LEFT REAR DOOR AJAR. Displayed when the driver’s rear door is not completely closed. RIGHT REAR DOOR AJAR. Displayed when the passenger side rear door is not completely closed. LIFTGATE AJAR. Displayed when the liftgate is not completely closed. PARK BRAKE SET. Displayed when the manual park brake is set. If the warning stays on after the park brake is released, contact your authorized dealer as soon as possible.

81

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

CHECK BRAKE SYSTEM. Displayed when the braking system is not operating properly. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. CHECK BRAKE LAMPS. Displayed when the brake lamps are activated and at least one is burned out. Check the lamps as soon as possible and have the burned out lamp replaced. The center high-mount brakelamp is not monitored. CHECK LEFT OR RIGHT HEADLAMPS. Displayed when the headlamps are activated and at least one is burned out. Check the lamps as soon as possible and have the burned out lamp replaced. Refer to Replacing headlamp bulbs in the Lights chapter. CHECK LEFT OR RIGHT PARK LAMPS. Displayed when the park lamps are activated and at least one is burned out. Check the lamps as soon as possible and have the burned out lamp replaced. CHECK LEFT OR RIGHT TURN LAMPS. Displayed when the turn signals are activated and at least one is burned out. Check the lamps as soon as safely possible and have the burned out lamp replaced. LOW TIRE PRESSURE. Displayed when one or more tires on your vehicle have low tire pressure. Refer to Inflating Your Tires in the Tires, Wheels and Loading chapter. TIRE PRESSURE MONITOR FAULT. Displayed when the Tire Pressure Monitoring System is malfunctioning. If the warning stays on or continues to come on, have the system inspected by your authorized dealer. TIRE PRESSURE SENSOR FAULT. Displayed when a tire pressure sensor is malfunctioning, or your spare tire is in use. For more information on how the system operates under these conditions, refer to Understanding Your Tire Pressure Monitoring System in the Tires, Wheels and Loading chapter. If the warning stays on or continues to come on, have the system inspected by your authorized dealer LOW FUEL LEVEL. Displayed when the fuel level in the fuel tank is at or near empty. WASHER FLUID LOW. Indicates the washer fluid reservoir is less than one quarter full. Check the washer fluid level. Refer to Windshield washer fluid in the Maintenance and Specifications chapter. CHANGE OIL SOON. Displayed when the engine oil life remaining is 5
percent or less. When oil life left is between 5% and 0%, the CHANGE OIL SOON message will be displayed. When oil life left reaches 0%, the OIL CHANGE REQUIRED message will be displayed.

82

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

An oil change is required whenever indicated by the message center. USE ONLY RECOMMENDED ENGINE OILS. To reset the oil monitoring system to 100% after each oil change [approximately 5,000 miles (8,000 km) or 180 days] perform the following: 1. Press the SETUP control to access the System Check function.

2. Press and release the RESET control to display “OIL LIFE XX% HOLD RESET NEW”.

3. Press and hold the RESET control for 2 seconds to display “IF NEW OIL HOLD RESET”.

4. Press and hold the RESET control to display “OIL LIFE SET TO 100%”. Your oil life is now reset.

To reset the oil monitoring system to your personalized oil life %: 1. Press the SETUP control to access the System Check function.

83

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

2. Press and release the RESET control to display “OIL LIFE XX% HOLD RESET NEW”.

3. Press and hold the RESET control for 2 seconds to display “IF NEW OIL HOLD RESET”.

4. Release the RESET control momentarily, then press RESET and SETUP controls at the same time to activate a service mode which will display “OIL LIFE XX% RESET TO ALTER”. 5. Press RESET until you find your personalized OIL LIFE XX%. 6. With your personalized OIL LIFE XX% displayed, press SETUP to continue the system check. DATA ERR. These messages indicate improper operation of the vehicle network communication between electronic modules. • Fuel Computer • Oil life • Charging system • Door sensor • Liftgate sensor • Exterior lamps • Traction control • Washer fluid • Brake Fluid Contact your authorized dealer as soon as possible if these messages occur on a regular basis.

84

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

POSITIVE RETENTION FLOOR MAT (IF EQUIPPED)

Do not install additional floor mats on top of the factory installed floor mats as they may interfere with the accelerator or the

brake pedals.

To install floor mats that have a retention post: Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal. To remove the floor mat, reverse the installation procedure.

LIFTGATE Unlock the liftgate (but not release it) with the power door lock system and remote entry transmitter. To open the liftgate, pull the liftgate handle rearward. • Do not open the liftgate in a garage or other enclosed area with a low ceiling. If the liftgate is opened, the liftgate could be damaged against a low ceiling.

• Do not leave the liftgate open while driving. Doing so could cause

serious damage to the liftgate and its components as well as allowing carbon monoxide to enter the vehicle.

Make sure that the liftgate door is closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent

passengers and cargo from falling out. If you must drive with the liftgate door open, keep the vents open so outside air comes into the vehicle.

85

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

POWER LIFTGATE (PLG) (IF EQUIPPED) With this option, you can power open or close the liftgate with the provided controls. • overhead console button • remote entry transmitter button • outside release handle • liftgate trim-mounted switch (closing) Opening and Closing the PLG: The PLG controls will operate without having the key in the ignition. The transaxle must be in PARK to power operate the PLG, when the key is in the ignition and turned to the ON position. When the liftgate is being power closed, a chime will sound three times before the liftgate begins to power close. A single chime indicates a problem with the close request. A faster chime indicates there is an excessive load on the liftgate (snow, bike rack, etc.) or a possible strut malfunction. If the excessive load is removed and you still have a faster chime, have the system serviced immediately by your authorized dealer.

WARNING: Make sure all persons are clear of the power liftgate area before using the power liftgate controls to open or close the

liftgate.

Keep the keys out of the reach of children. Do not allow children to play on or near an open or moving power liftgate.

Exercise care, when power opening or closing the PLG in a garage or other enclosed area with a low ceiling or close to a wall/garage door. The PLG could be damaged from the contact. Do not attempt to manually force the PLG to travel faster than the power system will permit. When power operating the PLG at temperatures below 32° F (0° C), the PLG may stop about 5 inches (12.7 cm) from the full open position. The PLG can be fully opened by pushing it upward to the maximum open position.

86

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

The Power Door Lockout Control is located in the overhead console. With the control in the OFF position, power operation is disabled from the liftgate handle and from the liftgate trim switch. The overhead console switch and remote entry transmitter will operate the liftgate regardless of the position of the lockout switch. To power open or close the PLG from the Overhead console: 1. Press and release the control to power open the PLG. 2. Press and release the control again to power the PLG closed. To power open or close the PLG with the Remote entry transmitter: 1. Press this control twice within three seconds to power open the PLG. The interior lamps will illuminate. 2. Press this control another two times within three seconds to close the PLG and turn off the interior lights. Refer to Remote Entry System in the Locks and Security chapter. To power open the PLG with outside release handle: 1. Ensure that the Power Door Lockout Control in the overhead console is ON. 2. Ensure that the PLG is unlocked, using the remote entry transmitter or power door unlock. Refer to Remote Entry System in the Locks and security chapter. 3. Pull up on the liftgate handle to engage the power assist feature. Release the handle as soon as the PLG begins to power open.

87

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Note: Continued force applied after unlatching may activate the obstacle detection feature and stop the power system. For the best performance allow the power system to open the PLG after releasing the handle. To power close the PLG from the liftgate trim switch: 1. Ensure the Power Door Lockout Control is in the ON position. 2. Press and release the control on the bottom of the liftgate trim panel to engage the power assist feature. If a single chime is heard, check to be sure that the Power Door Lockout Switch is set to ON and that the transaxle is in Park. To operate the PLG manually: 1. Disable the liftgate power function by placing the Power Door Lockout Control in the OFF position. 2. Open and close the liftgate as you would a standard liftgate. Note: In case of operation in extreme cold -40° F (-40° C), or on extreme inclines, manual operation of the liftgate is suggested. Safety/Obstructions If anything obstructs the PLG while it is power opening or closing, the PLG will automatically reverse or stop depending on the position of the liftgate, provided it meets sufficient resistance. If the PLG encounters an obstacle while closing, the PLG will reverse to full open. Once the obstacle is removed, the PLG can be again closed under power. If the PLG encounters an obstacle while opening, the PLG will stop when it encounters a solid obstacle. Close the liftgate manually and remove the obstruction. Normal operation can then be resumed. Resetting the PLG: The power liftgate may not operate properly if any of the following conditions occur: • a low voltage or dead battery • disconnected battery • the liftgate has been left open or unlatched for more than six (6)

hours

88

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

If any of these conditions occur, the PLG must be reset. To reset the PLG: 1. Manually close and fully latch the liftgate. 2. Power open the liftgate by using the remote entry transmitter or overhead console button. 3. Once the liftgate is fully open, close the liftgate using the power switch on the liftgate, remote entry transmitter or overhead console button. Liftgate ajar signal If the liftgate is not fully latched, you will receive a “LIFTGATE AJAR” message on the instrument panel. If you see this message, check the liftgate to ensure it is fully latched.

Make sure the liftgate is closed to prevent exhaust fumes from being drawn into the vehicle. If you must drive with the liftgate

open, keep the climate control vents open so that fresh outside air circulates through the vehicle.

CARGO AREA FEATURES

Cargo net (if equipped) The cargo pouch net secures lightweight objects in the cargo area. Attach the net to the anchors provided. Do not put more than 50
lbs. (22 kg) in the net.

The cargo net is not designed to restrain objects

during a collision or heavy braking.

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

89

Driver Controls

Utility hooks The utility hooks can be used to hang small items. Do not hang more than 20 lb. (12 kg) on each of the hooks. The hooks are not designed to restrain objects during a collision.

LUGGAGE RACK (IF EQUIPPED) Maximum load is 125 lbs (57 kg) on the roof rack structure, or 100 lbs (45 kg) on the roof panel, evenly distributed. If it is not possible to distribute the load, position it as far rearward as possible.

To adjust the cross-bar (if equipped) position: 1. Loosen the thumbwheel at both ends of the cross-bar (both cross-bars are adjustable). 2. Slide the cross-bar to the desired location. 3. Tighten the thumbwheel at both ends of the cross-bar.

90

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

To remove the cross-bar assembly (if equipped): 1. Remove rear support covers from the rear rails. Place a small object into the pin holes and slide the cover out towards the rear of the vehicle.

2. Loosen the thumbwheel at both ends of the cross-bar and slide the cross-bar towards the rear of the vehicle.

3. De-press the metal retention clip located in the inner rail channel on both sides, and slide the crossbar out simultaneously.

91

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

To reinstall the cross-bar assembly (if equipped): 1. Slide the cross-bar into the rail track with the arrow facing towards the front of the vehicle. Slide the bar forward passed the retaining clip. 2. Firmly tighten the thumbscrews at both ends of the cross-bar. 3. Install both support covers by sliding the covers back into the channel and pushing gently into place. Note: When the cross-bars are not in use, remove or move the cross-bars to the back of the roof rack for optimum wind noise.

92

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer. You should always carry a second key with you in a safe place in case you require it in an emergency. Refer to the SecuriLock娂 passive anti-theft system section in this chapter for more information.

POWER DOOR LOCKS Press the top portion of the control to unlock all doors and the bottom portion to lock all doors.Note: When the perimeter alarm is armed, the power door locks “inhibit” state is enabled and this switch is disabled.

Memory lock If you lock your doors with the power lock switch, the keyless entry system or the remote entry transmitter while the sliding door is open, the door will automatically lock after it is closed.

Smart locks (if equipped) This feature prevents you from locking yourself out of the vehicle if your key is still in the ignition. When you open the driver’s door and you lock the vehicle with the power door lock control, all the doors will lock, then the driver’s door will automatically unlock reminding you that your key is still in the ignition. The vehicle can still be locked, with the key in the ignition, using the manual lock button on the door, locking the driver’s door with a key, by simultaneously pressing button 7 • 8 and the 9 • 0 controls on the remote entry keypad (if equipped), or using the lock button on the remote entry transmitter (if equipped).

93

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Unlocking the liftgate during a battery failure In the event of a vehicle power failure affecting the liftgate latch, the liftgate can be unlocked manually. 1. Locate the liftgate trim access panel in the center of the liftgate. 2. Using your key, a small screwdriver or knife, pry off the access panel. 3. Using your key, a small screwdriver or knife, poke or cut a hole in the liftgate door foam as large as the access window and move the lock/unlock lever accordingly: • For vehicles without power liftgate, pull the lock/unlock lever to the right (drivers side).

• For vehicles with power liftgate, pull the lock/unlock lever toward you (toward the front of the vehicle).

Once the lock/unlock lever has been moved, you can open the liftgate from the outside liftgate handle.

94

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

CHILDPROOF DOOR LOCKS • When these locks are set, the sliding doors cannot be opened with the inside handle. • The sliding doors can be opened from the outside when the doors are unlocked.

The childproof lock controls are located on front edge of each sliding door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors. • Move lock control up to engage the childproof lock feature. • Move control down to disengage childproof lock feature. If your vehicle is equipped with power sliding door(s), refer to the Power sliding door section of this chapter for more information on how the childproof locks operate with this system.

REMOTE ENTRY SYSTEM This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The typical operating range for your remote entry transmitter is approximately 33 feet (10 meters). A decrease in operating range could be caused by: • weather conditions, • nearby radio towers, • structures around the vehicle, or • other vehicles parked next to your vehicle.

95

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security • 3–button remote

• 5–button remote

• 6–button remote

power sliding door (if equipped).

The remote entry system allows you to: • lock or unlock all vehicle doors and liftgate without a key. • unlock/open a driver’s side power sliding door and/or passenger side • unlock/open the power liftgate (PLG) (if equipped). • activate the personal alarm. • arm and disarm the perimeter anti-theft system (if equipped).

96

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

If there are problems with the remote entry system, make sure to take ALL remote entry transmitters with you to the authorized dealer in order to aid in troubleshooting the problem.

and release to unlock the driver’s door. Note: The interior

Unlocking the doors 1. Press lamps will illuminate and the anti-theft system (if equipped) will disarm. 2. Press and the liftgate.

and release again within three seconds to unlock all doors

Opening/closing power sliding doors (if equipped) • 5–button remote

• 6–button remote

• Press this control twice within three seconds to open the power • Press this control another two times within three seconds to close the

sliding door. The interior lamps will illuminate.

power sliding door and turn off the interior lights.

97

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Opening power liftgate (PLG) (if equipped) Press the control twice within three seconds to power open the power liftgate. The interior lamps will illuminate.

Make sure all persons are clear of the power liftgate

area before using the power liftgate controls to open or close the liftgate.

Press the control another two times within three seconds to close the power liftgate and turn off the interior lights. If anything obstructs the power liftgate while it is power opening or closing, the power liftgate will automatically reverse or stop depending on the position of the liftgate, provided it meets sufficient resistance. If the power liftgate encounters an obstacle while closing, the power liftgate will reverse to full open. Once the obstacle is removed, the power liftgate can be again closed under power. If the power liftgate encounters an obstacle while opening, the power liftgate will stop when it encounters a solid obstacle. Close the liftgate manually and remove the obstruction. Normal operation can then be resumed.

Make sure the power liftgate is closed to prevent exhaust fumes from being drawn into the vehicle. If you must drive with the

liftgate open, keep the climate control vents open so that fresh outside air circulates through the vehicle.

For more information regarding the operation of the power liftgate, refer to Power liftgate (PLG) (if equipped) in the Driver Controls chapter.

and release to lock all the doors and liftgate. The parking

Locking the doors 1. Press lamps will flash once if all doors, the liftgate and the hood (if equipped with perimeter alarm) are closed and locked. and release again within three seconds to confirm that all the 2. Press doors and liftgate are closed and locked. Note: The doors will lock again, the horn will chirp once, and the parking lamps will flash once more.

98

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

If any of the doors, the liftgate or the hood (if equipped with perimeter alarm) are not properly closed, the horn will make two quick chirps and the parklamps will not flash.

to activate the alarm. The alarm will cycle the horn, the turn

Sounding a panic alarm Press signals will flash, and the interior lamps will illuminate. Press again or turn the ignition to the 4 (ON) or the 1 (ACCESSORY) position to deactivate.

Replacing the battery The remote entry transmitter uses one coin type three-volt lithium battery CR2032 or equivalent. To replace the battery: 1. Twist a thin coin between the two halves of the remote entry transmitter near the key ring. DO NOT TAKE THE RUBBER COVER AND CIRCUIT BOARD OFF THE FRONT HOUSING OF THE REMOTE ENTRY TRANSMITTER.

2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board.

3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery. Press the battery down to ensure that the battery is fully seated in the battery housing cavity.

99

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

5. Snap the two halves back together. Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmitter should operate normally after battery replacement.

Replacing lost remote entry transmitters If you would like to have your remote entry transmitter reprogrammed because you lost one, or would like to buy additional remote entry transmitters, you can either reprogram them yourself, or take all remote entry transmitters to your authorized dealer for reprogramming. How to reprogram your remote entry transmitters You must have all remote entry transmitters (maximum of six) available before beginning this procedure. To reprogram the remote entry transmitters:

1. Ensure the vehicle is electronically unlocked. 2. Put the key in the ignition. 3. Turn the key from the 3 (OFF) position to 4 (ON). 4. Cycle eight times rapidly (within 10 seconds) between the 3 (OFF) position and 4 (ON). Note: The eighth turn must end in the 4 (ON) position. 5. The doors will lock, then unlock, to confirm that the programming mode has been activated. 6. Within 20 seconds press any button on the remote entry transmitter. Note: If more than 20 seconds have passed you will need to start the procedure over again. 7. The doors will lock, then unlock, to confirm that this remote entry transmitter has been programmed.

100

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

8. Repeat Step 6 to program each additional remote entry transmitter. 9. Turn the ignition to the 3 (OFF) position after you have finished programming all of the remote entry transmitters. 10. The doors will lock, then unlock, to confirm that the programming mode has been exited.

is pressed, or

Illuminated entry The interior lamps illuminate when the key in the driver’s door lock cylinder (if equipped with perimeter alarm), the keyless entry system or the remote entry transmitter is used to unlock the door(s), power sliding doors (if equipped) or liftgate. The illuminated entry system will turn off the interior lights if: • the ignition switch is turned to the 4 (ON) position, or • the keyless entry system or the remote entry transmitter lock control • after 25 seconds of illumination. The panel dimmer control must not be set to the off position for the illuminated entry system to operate. The inside lights will not turn off if: • they have been turned on with the panel dimmer control, or • any door, power sliding door (if equipped) or the liftgate is open. The battery saver will shut off the interior lamps 30 minutes after the last door is closed, even if the panel dimmer control is left on. Illuminated exit • The interior lights will illuminate when the key is removed from the • When the headlamp control is on the “sleeping baby mode”, only the

ignition.

lower interior lights will illuminate.

The system automatically turns off after 25 seconds. The panel dimmer control must not be set to the off position for the illuminated exit to operate.

101

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

keypad, or

Perimeter lamps illuminated entry (if equipped) The exterior lamps illuminate when the vehicle is unlocked using the remote entry transmitter, keyless keypad, or the driver’s door key lock cylinder (if equipped with perimeter alarm). The following items will illuminate: • Puddle lamps • Head lamps • Park lamps • Tail lamps The system will automatically turn off if: • the vehicle is locked using the remote entry system, the keyless entry • the ignition is turned to the 4 (ON) position, or • after 25 seconds of illumination. Deactivating/activating perimeter lamps You may enable/disable this feature by having your vehicle serviced by your authorized dealer. You may also perform the following power door lock sequence to enable/disable the perimeter lamps feature: 1. Turn the ignition to the 4 (ON) position, then press the power door unlock control 3 times. 2. Turn the ignition to the 3 (OFF) position, then press the power door unlock control 3 times. 3. Turn the ignition to 4 (ON) position. Completing the sequence within 30 seconds enters a program mode and is confirmed by a horn chirp. Activating or deactivating perimeter lighting once in program mode is accomplished by: • Pressing the power door unlock control twice within five seconds. At

this point, perimeter lighting will be activated if it was previously deactivated, and deactivated if it was previously activated. Confirmation of perimeter lighting being activated is provided by a short horn chirp followed by a long horn sound; Confirmation of perimeter lighting being deactivated is provided by a short horn chirp only. • Exiting the program mode is accomplished by turning the ignition to any position other than the 4 (ON) position, or two minutes elapsing since the program mode was entered.

102

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Note: The puddle lamps cannot be deactivated. Performing this deactivation procedure will only deactivate the head, park and tail lamps. For information regarding perimeter lamps delay, refer to Autolamps - Programmable exit delay in the Lights chapter.

to automatically move the driver seat, side view mirrors and

Memory feature (if equipped) The remote entry system allows you to recall the memory seat/side view mirrors/adjustable pedals feature. Press adjustable pedals to the desired memory position. Associating the remote transmitter with the memory feature To activate this feature: 1. Position the driver’s seat, side view mirrors and adjustable pedals to the positions you desire. 2. Press the SET control on the door next to the window inside from the mirror. 3. Within 5 five seconds, press any control on the remote transmitter and then press the 1 or 2 control on the driver’s door panel to associate with the Driver 1 or Driver 2
positions. 4. Repeat this procedure for another remote transmitter if desired. Disassociating the memory feature from the remote transmitter To deactivate this feature: 1. Press the SET control on the driver’s door panel. 2. Within 5 five seconds, press any control on the remote transmitter which you would like to deactivate and then press the SET control on the driver’s door panel again. 3. Repeat this procedure for another remote transmitter if desired.

103

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

KEYLESS ENTRY SYSTEM (IF EQUIPPED) You can use the keyless entry keypad to:

• lock or unlock the doors without using a key. • activate or deactivate the autolock feature. • open and close the right and left power sliding doors (if equipped). • recall memory seat/side view mirrors/adjustable pedals position Driver

1 or Driver 2 (if equipped).

The keypad can be operated with the factory set 5–digit entry code; this code is located: • on the owner’s wallet card in the glove box, • marked on the passenger compartment fuse panel (located below and • and is available from your

to the left of the steering, near the brake pedal),

authorized dealer.

You can also create your own 5–digit personal entry code. When pressing the controls on the keypad, press the middle of the controls to ensure a good activation.

Programming a personal entry code To create your own personal entry code(s): 1. Enter the factory set code. Note: The driver’s door will unlock. 2. Within five seconds press and release the 1 • 2 on the keypad. Note: The lock motors will cycle, locked then unlocked. 3. Enter your personal 5-digit code. Each number must be entered within five seconds of each other.

104

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

4. Enter a sixth digit if you wish to have the personal entry code recall memory position Driver 1 or Driver 2 (if equipped with the memory seat/side view mirrors/adjustable pedals feature). Note: The lock motors will cycle, locked then unlocked. • Press 1 • 2 to recall the Driver 1 position. • Press 3 • 4 to recall the Driver 2 position. 5. After five seconds of keypad inactivity, programming mode is exited. All of the vehicle doors will lock and unlock to confirm the code has been stored. Each memory feature driver position (Driver 1 or Driver 2) can be associated with only one personal code. The factory-set code cannot be associated with a memory recall position. You can program up to three personal codes; these codes do not replace the factory-set code. Tips for setting codes: • The factory set code cannot be erased or changed. • The factory code will work even after you have set your own personal • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order. Erasing personal code 1. Enter the factory set 5–digit code. 2. Within five seconds of entering the factory code, press and release the 1 • 2 control. The door locks will lock and quickly unlock to confirm entry into the programming mode. 3. Within five seconds of Step 2, press and hold the 1 • 2 for two seconds to erase the customer programmed code. The programming mode is exited after five seconds of keypad inactivity. The door locks will lock and quickly unlock to confirm programming mode has been exited. The personal code is now erased and only the factory set 5–digit code will work.

codes.

105

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Unlocking and locking the doors using keyless entry To unlock the driver’s door, enter the factory set 5-digit code or your personal code. Each number must be pressed within five seconds of each other. The keyless entry keypad will illuminate after pressing the first control on the keypad. To unlock all doors, press the 3 • 4 control within five seconds. To lock all doors, press the 7 • 8 and the 9 • 0 at the same time. You do not need to enter the keypad code first. Note: The interior lamps will turn off. To open (or close) the power sliding doors (if equipped), press the 5 • 6 control within five seconds to open (or close) the left power sliding door or the 9 • 0 control in order to open (or close) the right power sliding door.

Autolock This feature automatically locks all vehicle doors when: • all doors are closed, • the ignition is in the 4 (ON) position, • the brake is pressed before reaching 5 mph (8 km/h), and • then the vehicle increases to more than 5 mph (8 km/h). Relock The autolock feature repeats when: • an “autolock” occurrence has already taken place, • the brake is depressed while vehicle speed is less than 5 mph (8
• all vehicle doors become closed again, and • then the vehicle increases to more than 5 mph (8 km/h). Deactivating/activating the autolock feature The autolock feature can be enabled or disabled by the keyless entry keypad (if equipped) on your door, driver configuration mode or by your authorized dealer.

km/h),

106

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Deactivating/reactivating the autolock feature using the keypad (if equipped) Your vehicle comes with the autolock feature activated. To deactivate/reactivate this feature: 1. Turn the ignition to the 3 (OFF) position. 2. Close all the doors. 3. Enter the 5-digit entry code. 4. Press and hold the 7 • 8. While holding the 7 • 8, press the 3 • 4. 5. Release the 3 • 4. 6. Release the 7 • 8. The horn will chirp once when the system has been successfully deactivated. The horn will chirp twice (one short and one long chirp) when the system has been successfully reactivated. To deactivate/reactivate the autolock feature using the power door unlock control You must close all the vehicle doors and complete Steps 1-7 within 30
seconds or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait 30 seconds. 1. Turn the ignition key to the 4 (ON) position. 2. Press the power door unlock control three times. 3. Turn the ignition key from the 4 (ON) position to the 3 (OFF) position. 4. Press the power door unlock control three times. 5. Turn the ignition back to the 4 (ON) position. The horn will chirp. 6. Press the unlock control, then press the lock control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. 7. Turn the ignition to the 3 (OFF) position. The horn will chirp once to confirm the procedure is complete.

107

2006 Freestar (win) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEM SecuriLock娂 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from being started unless a coded key programmed to your vehicle is used. The SecuriLock娂 passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection.

Anti-theft indicator The anti-theft indicator is located on top of the instrument panel.