Login- Download PDF Manual
-
1. Temperature control: Determines temperature level. 2. Mode selector: Press to select air flow direction to or •
(panel). directs air to the floor of the
(floor)
•
third row seating.
directs air to the overhead
registers of the second and third row seating.
The selected mode will illuminate on the temperature control. 3. Fan control: Determines fan speed levels. If your vehicle is equipped with the front Dual Automatic Temperature Control (DATC) system, when the front system is turned off, the fan and heat mode will operate and A/C will be unavailable.
46
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Climate Controls
FLOOR CONSOLE CLIMATE CONTROLS Controls the direction of the airflow to the rear of the vehicle. •
directs air flow primarily
through the console panel register.
directs air flow through the console floor register.
•
REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog. • A small LED will illuminate when
the rear defroster is activated.
The ignition must be in the 3 (ON) position to operate the rear window defroster. The defroster turns off automatically after 10 minutes or when the ignition is turned to the 1 (OFF/LOCK) or 2 (ACC) position. To manually turn off the defroster before 10 minutes have passed, push the control again.
47
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Lights
HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps.
Turns the headlamps on.
Autolamp Control (if equipped) The autolamp control sets the headlamps to turn on and off automatically. The autolamp control, located on the headlamp control, may be set to: • turn on the lamps automatically • turn off the lamps automatically • keep the lamps on for up to three minutes after the key is turned to
during the daylight
at night
OFF.
To turn the autolamps on, rotate the control counterclockwise to
or
Foglamp control (if equipped) The foglamps can be turned on only when the headlamp control is in position and the the high beams are not turned on. Pull headlamp control towards you to turn foglamps on. The foglamp icon indicator light below the will illuminate when foglamp is activated.
48
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Push the headlamp control towards the instrument panel to deactivate the foglamps.
Lights
Daytime running lamps (DRL) (if equipped) To activate DRL: • the ignition must be in the ON position and • the headlamp control is in the • the transmission is not in park.
or
position
Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Light (DRL) System
does not activate your tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.
High beams Push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate.
Flash to pass Pull the lever toward you to activate. Release the lever to deactivate.
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
49
Lights
PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel when exterior lights are on. • Rotate the thumbwheel from left
to right to brighten the instrument panel.
• Rotate the thumbwheel from right
to left to dim the instrument panel.
• Rotate to fully to the right (past detent) to turn on interior lamps. • Rotate to the left position (past detent) to turn off the interior lamps
and will also disable the illuminated entry feature.
AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed before leaving the assembly plant. If your vehicle is involved in an accident or if you have problems fixing the alignment of your headlamps, have them checked by a qualified service technician. Headlamp aim adjustment The headlamps on your vehicle can only be vertically adjusted. Your vehicle does not require horizontal aim adjustments. To adjust the headlamps: 1. Park your vehicle on a level surface about 25 feet (7.6 meters) away from a vertical plain surface (3). Check your headlamp alignment at night or in a dark area so that you can see the headlamp beam pattern. • (1) Eight feet • (2) Center height of lamp to • (3) Twenty-five feet • (4) Horizontal reference line 2. The center of the headlamp has a 3.0 mm circle on the lens. Measure the height from the center of your headlamp to the ground (2) and mark an 8 foot (2.4 meter) long horizontal line on the plain surface (1) at this height (masking tape works well).
ground
50
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Lights
51
3. Turn on the low beam headlamps. The brightest part of the light should be below the horizontal line (4). If it is above the line the headlamp will need to be adjusted. 4. Open the hood.
5. Locate the vertical adjuster for each headlamp. Adjust the aim by turning the adjuster control either clockwise (to adjust down) or counterclockwise (to adjust up). Note: Use a 4 mm socket or box wrench to turn the vertical adjuster control. 6. Horizontal aiming is not required for this vehicle and is non-adjustable.
TURN SIGNAL CONTROL • Push down to activate the left • Push up to activate the right turn
turn signal.
signal.
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Lights
INTERIOR LAMPS
Dome/reading lamps The dome lamp lights when: • any door is opened. • the instrument panel dimmer switch is rotated up until the courtesy lamps come on.
• any of the remote entry controls are pressed and the ignition is OFF.
The reading portion, the two outer lights, can only be toggled on and off at the lamp. The front map lamps are located in the overhead console (if equipped). Press the controls on either side of each map lamp to activate the lamps.
Cargo/reading lamps The dome portion of the lamp or the center light can be turned on when the panel dimmer control is rotated fully up or when a door is opened. The rear dome lamp can be turned ON or OFF by sliding the control.
BULB REPLACEMENT
Headlamp Condensation The headlamps are vented to equalize pressure. When moist air enters the headlamp(s) through the vents, there is a possibility that condensation can occur. This condensation is normal and will clear within 45 minutes of headlamp operation.
52
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Lights
Replacing exterior bulbs Check the operation of all the bulbs frequently.
Replacing the interior bulbs Check the operation of the bulbs frequently. To replace any of the interior bulbs, see a dealer or qualified technician.
H13
Trade number
Number of bulbs
Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to ensure lamp performance, light brightness and pattern and safe visibility. Using incorrect bulbs may damage the lamp assembly or void the lamp assembly warranty or may not provide quality bulb burn time. Function Headlamp low & high beam Front park/turn lamp Side park/turn lamp Upper rear tail lamp Rear backup lamp Lower rear stop/tail/turn lamp High-mount stop lamps Rear license plate lamps Front fog lamp Cargo lamp Interior overhead lamp Front door courtesy lamp Map lamps Ashtray lamp All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your authorized dealer .
3457 NAK (amber)
168
9145
211-2194
194
921168 (T10)
912 (906)
W5WL
4057K
168
161
53
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Lights
Replacing headlamp bulbs Do not touch the glass of a halogen bulb. 1. Turn off the headlamps and open the hood. 2. Remove three screws from the headlamp assembly and pull headlamp forward.
3. Disconnect the electrical connector. 4. Remove the old bulb by turning counterclockwise and pull it out.
Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.
Reverse steps to reinstall bulb(s).
54
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Lights
Replacing front parking lamp/turn signal/sidemarker bulbs 1. Turn off the headlamps and open the hood. 2. Remove three screws from the headlamp assembly and pull headlamp forward.
3. Rotate the bulb socket counterclockwise and remove it from the lamp assembly. 4. Pull the bulb straight out of the socket.
Reverse steps to reinstall bulb(s).
Replacing tail/brake/turn/backup lamp bulbs 1. Turn the headlamp switch to OFF and open the liftgate. 2. Remove the two bolts from the lamp assembly. 3. Remove the lamp assembly.
55
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Lights
4. Rotate the bulb socket counterclockwise and remove it from the lamp assembly. 5. Pull the bulb straight out of the socket. Reverse steps to reinstall bulb(s).
Replacing foglamp bulbs 1. Make sure the headlamp switch is in the OFF position. 2. Remove the bulb socket from the foglamp by turning it counterclockwise. 3. Disconnect the electrical connector.
Reverse steps to reinstall bulb(s).
Replacing license plate lamp bulbs 1. Make sure the headlamp switch is in the OFF position. 2. Remove the lamp assembly by depressing the small tab and rocking the lamp assembly out. 3. Remove the bulb socket from the lamp assembly by turning counterclockwise and pull the bulb straight out. Reverse steps to reinstall bulb(s).
56
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Replacing high-mount brakelamp bulb 1. Remove the two screws and lamp assembly away from the vehicle.
Lights
2. Remove the bulb holder from the lamp assembly by depressing the snaps.
3. Pull the bulb straight out of the socket and push in the new bulb.
Reverse steps to reinstall bulb(s).
57
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers.
Windshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick push and hold: the wipers
will swipe three times with washer fluid.
• a long push and hold: the wipers and washer fluid will be activated for
up to ten seconds.
Windshield wiper features (if equipped with Autolamp feature) The exterior lamps will turn on with the ignition on, Headlamp control in the Autolamp position and the windshield wipers are turned on (for a fixed period of time).
Rear window wiper/washer controls For rear wiper operation, rotate the rear window wiper and washer control to the desired position. Select: INT 1 — 8–10 second interval rear wiper. INT 2 — 3–4 second interval rear wiper. OFF — Rear wiper and washer off. For rear wash cycle, rotate (and hold as desired) the rear wiper/washer control to either From either position, the control will automatically return to the INT 2
or OFF position.position.
58
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
TILT STEERING COLUMN Pull the lever down and release, to unlock the steering column tilt lock. With the lever in the down position, tilt the steering column and wheel to its desired orientation. Do not push or pull the lever while tilting the wheel.
Lift the lever back to its original position to lock the steering column.
Never adjust the steering column when the vehicle is
moving.
ILLUMINATED VISOR MIRROR
(IF EQUIPPED) Lift the mirror cover to turn on the visor mirror lamps.
59
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
Slide on rod feature Rotate the visor towards the side window and extend it rearward for additional sunlight coverage. Note: To stow the visor back into the headliner, visor must be retracted before moving it back towards the windshield.
OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according to your option package.
Storage compartment Press the latch to open the storage compartment.
60
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: • Place the VELCRO威 hook onto
the side of the aftermarket transmitter opposite of the button.
• Place the transmitter into storage
compartment, button down.
• Place the provided height
adaptors onto the back of the door as needed. • Close the door. • Press the depression in the door
to activate the transmitter.
AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty.
61
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
The auxiliary power point is located in the floor console. Do not use the power point for operating the cigarette lighter element (if equipped). To prevent the fuse from being blown, do not use the power point(s) over the vehicle capacity of 12 VDC/180W. To prevent the battery from being discharged, do not use the power point longer than necessary when the engine is not running. Always keep the power point caps closed when not being used. Cigar/Cigarette lighter (if equipped) Do not plug optional electrical accessories into the cigarette lighter socket. Do not hold the lighter in with your hand while it is heating, this will damage the lighter element and socket. The lighter will be released from its heating position when it is ready to be used. Improper use of the lighter can cause damage not covered by your warranty.
Rear auxiliary power point (if equipped) A second auxiliary power point is located on the rear side of the console. It is accessible from the rear seats.
CENTER CONSOLE 1. Cupholders 2. Tissue holder in lid 3. Rear power point 4. Large utility compartment has an exterior power point in front of the lid, and inside the compartment has coin holder slots and a business/credit card holder The rear side of the console may incorporate the following features: • Air vents 62
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
• Cupholders
Use only soft cups in the cupholder. Hard objects can injure you in a collision.
Driver Controls
Rear center console features (if equipped) The rear center console incorporates the following features: • Utility compartment • Cupholders • Flip forward armrest to provide a
flat load floor
POWER WINDOWS
Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure
themselves.
When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in
the proximity of the window openings.
63
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
Press and pull the window switches to open and close windows. • Push down (to the first detent) and hold the switch to open. • Pull up and hold the switch to
close.
Rear Window Buffeting: When one or both of the rear windows are open, the vehicle may demonstrate a wind throb or buffeting noise; this noise can be eliminated by lowering a front window approximately two to three inches.
One touch down Allows the driver’s window to open fully without holding the control down. Push the switch completely down to the second detent and release quickly. The window will open fully. Momentarily press the switch to any position to stop the window operation.
Window lock The window lock feature allows only the driver to operate the power windows. To lock out all the window controls except for the driver’s press the right side of the control. Press the left side to restore the window controls.
Accessory delay With accessory delay, the window switches, audio system and moon roof (if equipped) may be used for up to ten minutes after the ignition switch is turned to the OFF position or until either front door is opened.
64
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
AUTOMATIC DIMMING INSIDE REAR VIEW MIRROR (IF EQUIPPED) Your vehicle may be equipped with an inside rear view mirror with an auto-dimming function. The electrochromic day/night mirror will change from the normal (high reflective) state to the non-glare (darkened) state when bright lights (glare) reach the mirror. When the mirror detects bright light from behind the vehicle, it will automatically adjust (darken) to minimize glare. The mirror will automatically return to the normal state whenever the vehicle is placed in R (Reverse) to ensure a bright clear view when backing up. Do not block the sensor on the backside of the inside rear view mirror since this may impair proper mirror performance.
EXTERIOR MIRRORS
Power side view mirrors The ignition must be in the ACC or ON position to adjust the power side view mirrors. To adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place.
65
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
Fold-away mirrors Carefully pull the outside mirrors inwards when driving through a narrow space, like an automatic car wash.
(if equipped)
Heated outside mirrors Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors. POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position. Press and hold the rocker control to adjust accelerator and brake pedal toward you or away from you.
The adjustment allows for approximately 3 inches (73 mm) of maximum travel.
Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving.
SPEED CONTROL (IF EQUIPPED) With speed control set, you can maintain a speed of 30 mph (48 km/h) or more without keeping your foot on the accelerator pedal. Speed control does not work at speeds below 30 mph (48 km/h).
66
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved.
Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed.
3. Press the SET + control and release it. 4. Take your foot off the accelerator pedal. 5. The indicator light instrument cluster will turn on.
on the
steep hill.
Note: • Vehicle speed may vary momentarily when driving up and down a • If the vehicle speed increases above the set speed on a downhill, you • If the vehicle speed decreases more than 10 mph (16 km/h) below
may want to apply the brakes to reduce the speed.
your set speed on an uphill, your speed control will disengage.
67
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
Resuming a set speed Press the RES (resume) control and release it. This will automatically return the vehicle to the previously set speed. The RES control will not work if the vehicle speed is not faster than 30 mph (48 km/h).
Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET + control until you get to the desired speed, then release the control. You can also use the SET + control to operate the Tap-Up function. Press and release this control to increase the vehicle set speed in small amounts by 1 mph (1.6 km/h).
• Use the accelerator pedal to get to the desired speed. When the vehicle reaches that speed press and release the SET + control.
• Depress the brake pedal until the desired vehicle speed is reached,
Reducing speed while using speed control There are two ways to reduce a set speed: • Press and hold the SET - control until you get to the desired speed, then release the control. You can also use the SET - control to operate the Tap-Down function. Press and release this control to decrease the vehicle set speed in small amounts by 1
mph (1.6 km/h).press the SET + control.
68
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal. This will not erase your vehicle’s previously • Press the speed control OFF
set speed.
control.
Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.
STEERING WHEEL CONTROLS (IF EQUIPPED) These controls allow you to operate some radio and climate control features.
Audio control features Press MEDIA to select: • AM, FM1, FM2
• TAPE (if equipped) • CD (if equipped) • DVD (if equipped) • SAT1, SAT2 or SAT3 (SatelliteRadio mode if equipped).
69
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
In AM, FM1, or FM2 mode: • Press to
SEEK
select preset stations within the selected radio band or press and hold to select the next/previous radio frequency.
In Satellite radio mode (if equipped): • Press
SEEK
to
advance through preset channels or subscribed channels.
In Tape mode: • Press
SEEK
to select the next selection on the tape or
press and hold to forward or reverse the tape.
In CD mode: • Press
SEEK
to select the next selection on the CD or
press and hold to forward or reverse the CD.
In any mode: • Press VOL + or − to adjust
volume.
70
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
Climate control features (if equipped) Press TEMP + or - to adjust temperature.
Press FAN + or - to adjust fan speed.
MOON ROOF (IF EQUIPPED) You can move the glass panel of the moon roof back to open or tilt up (from the closed position) to ventilate the vehicle.
Do not let children play with the moon roof or leave children unattended in the vehicle. They may seriously hurt themselves.
When closing the moon roof, you should verify that it is free of obstructions and ensure that children and/or pets are not in the
proximity of the moon roof opening.
To open the moon roof: The moon roof is equipped with an automatic, one-touch, express opening feature. Press and release the rear portion of the control. To stop motion at any time during the one-touch opening, press the control again.
71
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
To close the moon roof: The moon roof is equipped with an automatic, one-touch, express closing feature. Press and release the front portion of the control. To stop motion at any time during the one-touch closing, press the control again. Bounce back: When an obstacle has been detected in the moon roof opening as the moon roof is closing, the moon roof will automatically open and stop at a prescribed position. Bounce back override: To override bounce back, within 2 seconds after reaching bounce back position, if the switch is held in the close position the moon roof will close with a 20–25 percent increase of closing force before it will bounce back again. If the switch is released before the moon roof reaches fully closed position, the moon roof will stop. For example: Bounce Back Override can be used to overcome the resistance of ice on the moon roof or seals. To vent: • To tilt the moon roof into the vent position (when the glass panel is • To close the moon roof from the vent position, press and hold the rear
closed), press and hold the front portion of the control.
portion of the control until the glass panel stops moving.
The moon roof has a sliding shade that can be opened or closed when the glass panel is shut. To close the shade, pull it toward the front of the vehicle. Accessory delay: With accessory delay, the window switches, audio system, and moon roof (if equipped) may be used for up to 10 minutes after the ignition switch is turned to the OFF position or until either front door is opened.
HOMELINK姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink威 Wireless Control System, located on the overhead console, provides a convenient way to replace up to three hand-held transmitters with a single built-in device. This feature will learn the radio frequency codes of most transmitters to operate garage doors, entry gate operators, security systems, entry door locks, and home or office lighting.
72
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
When programming your HomeLink威 Wireless Control System to a garage door or gate, be sure that people and objects are out of
the way to prevent potential harm or damage.
Do not use the HomeLink威 Wireless Control System with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door which cannot detect an object, signaling the door to stop and reverse, does not meet current U.S. federal safety standards. For more information, contact HomeLink威 at: www.homelink.com or 1–800–355–3515. Retain the original transmitter for use in other vehicles as well as for future programming procedures (i.e. new HomeLink威 equipped vehicle purchase). It is also suggested that upon the sale of the vehicle, the programmed Homelink威 buttons be erased for security purposes, refer to Programming in this section.
Programming Do not program HomeLink威 with the vehicle parked in the garage. Note: Some vehicles may require the ignition switch to be turned to the second (or “ACC”) position for programming and/or operation of the HomeLink威. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink威 for quicker training and accurate transmission of the radio-frequency signal. 1. Press and hold the two outside buttons releasing only when the indicator light begins to flash after 20 seconds. Do not repeat Step 1
to program additional hand-held transmitters to the remaining two HomeLink威 buttons. This will erase previously programmed hand-held transmitter signals into HomeLink威. 2. Position the end of your hand-held transmitter 1–3 inches (2–8 cm) away from the HomeLink威 button you wish to program (located on your overhead console) while keeping the indicator light in view.73
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
3. Simultaneously press and hold both the HomeLink威 and hand-held transmitter button. Do not release the buttons until Step 4 has been completed. Some entry gates and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator and Canadian Programming” section for Canadian residents. 4. The indicator light will flash slowly and then rapidly. Release both buttons when the indicator light flashes rapidly. (The rapid flashing light indicates acceptance of the hand-held transmitters’ radio frequency signals.) 5. Press and hold the just-trained HomeLink威 button and observe the indicator light. If the light is constant, programming is complete and your device should activate when the HomeLink威 button is pressed and released. Note: To program the remaining two HomeLink威 buttons, begin with Step 2 in the “Programming” section — do not repeat Step 1. Note: If the indicator light blinks rapidly for two seconds and then turns to a continuous light, proceed with Steps 6 through 8 to complete programming of a rolling code equipped device. 6. At the garage door opener receiver (motor-head unit) in the garage, locate the “learn” or “smart” button (usually near where the hanging antenna wire is attached to the unit). 7. Press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer.) Note: There are 30 seconds in which to initiate Step 8. 8. Return to the vehicle and firmly press, hold for two seconds and release the HomeLink威 button. Repeat the press/hold/release sequence again, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming. HomeLink威 should now activate your rolling code equipped device. To program additional HomeLink威 buttons begin with Step 2 in the “Programming” section. For questions or comments, please contact HomeLink at www.homelink.com or 1–800–355–3515.
74
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
Gate Operator & Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink威 to accept the signal from the hand-held transmitter. After completing Steps 1 and 2
outlined in the “Programming” section, replace Step 3 with the following: Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent overheating. • Continue to press and hold the HomeLink威 button (note Step 3 in the“Programming” section) while you press and release — every two seconds (“cycle”) your hand-held transmitter until the frequency signal has been accepted by the HomeLink威. The indicator light will flash slowly and then rapidly after HomeLink威 accepts the radio frequency signal.
• Proceed with Step 4 in the “Programming” section.
Operating the HomeLink姞 Wireless Control System To operate, simply press and release the appropriate HomeLink威 button. Activation will now occur for the trained product (garage door, gate operator, security system, entry door lock, or home or office lighting etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficulties, contact HomeLink威 at www.homelink.com or 1–800–355–3515.
75
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
Erasing HomeLink姞 buttons To erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outer HomeLink威 buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds.
HomeLink威 is now in the train (or learning) mode and can be programmed at any time beginning with Step 2 in the “Programming” section. Reprogramming a single HomeLink姞 button To program a device to HomeLink威 using a HomeLink威 button previously trained, follow these steps: 1. Press and hold the desired HomeLink威 button. Do NOT release the button. 2. The indicator light will begin to flash after 20 seconds. Without releasing the HomeLink威 button, follow Step 2 in the “Programming” section. For questions or comments, contact HomeLink威 at www.homelink.com or 1–800–355–3515.
STANDARD MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position, the message center, located on your instrument cluster, displays important vehicle information through a constant monitor of vehicle systems. You may select display features on the message center for a display of status. The system will also notify you of potential vehicle problems with a display of system warnings followed by an indicator chime.
76
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
Selectable features Press and release the TRIP/RESET control switch to scroll and reset the following functions. Select or reset the function by holding the TRIP/RESET button for more that 2
seconds. Info menu This menu displays the following control displays: • Odometer/Trip Odometer (Trip A and Trip B) • Distance to Empty • Average Fuel Economy • Setup Menu Odometer/Trip odometer Refer to Gauges in the Instrument Cluster chapter. Distance to empty (DTE) Selecting this function from the INFO MENU estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling to allow this feature to correctly detect the added fuel. The DTE function will display LOW FUEL LEVEL and sound a tone for one second when you have approximately 50 miles (80 km) to empty. If you RESET this warning message, this display and tone will return within 10 minutes. DTE is calculated using a running average fuel economy, which is based on your recent driving history of 500 miles (800 km). This value is not the same as the average fuel economy display. The running average fuel economy is reinitialized to a factory default value if the battery is disconnected.77
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
service stations
Average fuel economy (AFE) Select this function to display your average fuel economy in miles/gallon or liters/km. If you calculate your average fuel economy by dividing miles traveled by gallons of fuel used (liters of fuel used by 100 kilometers traveled), your figure may be different than displayed for the following reasons: • Your vehicle was not perfectly level during fill-up • Differences in the automatic shut-off points on the fuel pumps at • Variations in top-off procedure from one fill-up to another • Rounding of the displayed values to the nearest 0.1 gallon (liter) 1. Drive the vehicle at least 5 miles (8 km) with the speed control system engaged to display a stabilized average. 2. Record the highway fuel economy for future reference. It is important to press the TRIP/RESET control switch (press and hold for 2 seconds in order to reset the function) after setting the speed control to get accurate highway fuel economy readings. Setup menu Press and hold the TRIP/RESET control switch to get to the SETUP MENU sequence from the INFO MENU for the following displays: • System Check • Units (English/Metric) • Language • Autolamp • Autolock • Autounlock • Park Aid (if equipped) • Oil Life Start Value Briefly press the TRIP/RESET control switch to scroll through the SETUP MENU display sequence. If the TRIP/RESET control switch is not pressed within 4 seconds, the message center returns to the Info Menu.
78
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
System check Press and hold the TRIP/RESET control switch to select SYSTEM CHECK when “SYSTEM CHECK / HOLD RESET” is displayed in the message center. Selecting this function from the SETUP MENU causes the message center to cycle through each of the systems being monitored. For each of the monitored systems, the message center will indicate either an OK message or a warning message for two seconds. Pressing the TRIP/RESET control switch cycles the message center through each of the systems being monitored. The sequence of the system check report and how it appears in the message center is as follows: 1. OIL LIFE RESET 2. CHARGING SYSTEM 3. WASHER FLUID 4. DOOR AJAR 5. EXTERIOR LAMP 6. BRAKE SYSTEM 7. PARK BRAKE 8. MILES TO EMPTY 9. FUEL LEVEL LOW (will only display if 50 miles or less to empty) To reset the oil monitoring system to 100% after each oil change [approximately 5,000 miles (8,000 km) or 180 days] perform the following: 1. Enter SYSTEM CHECK to display “HOLD RESET IF NEW OIL”.
79
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
2. Press and hold the RESET control switch for more than 2
seconds. Oil life is set to 100% and “OIL LIFE SET TO 100%” is displayed. Note: To change oil life 100% miles value from 5,000 miles (8,000 km) or 180 days to another value, refer to the Oil Life Start Value selected from the SETUP MENU in this section. Units (English/Metric) 1. Select this function from the SETUP MENU for the current units to be displayed. 2. Press and hold the TRIP/RESET control switch to change from English to Metric. 3. Press the TRIP/RESET control switch for the next SETUP MENU item or wait for more than 4 seconds to return to the INFO MENU. Language Note: When entering the SETUP MENU and a non-English language has been selected, “PRESS RESET FOR ENGLISH” will be displayed to change back to English. 1. Select this function from the SETUP MENU for the current language to be displayed. 2. Press and hold the TRIP/RESET control to select a new language.Selectable languages are English, Spanish, French, Japanese, or Arabic. 3. Press the TRIP/RESET control switch for the next SETUP MENU item or wait for more than 4 seconds to return to the INFO MENU. Autolamp This feature keeps your headlights on for up to three minutes after the ignition is switched off.
80
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
1. To change the time delay of the autolamp feature, select this function from the SETUP MENU. 2. Press and hold the TRIP/RESET control switch to select the new Autolamp delay time (in seconds) values of 0, 10, 20, 30, 60, 90, 120 or 180 and wraps back to 0. Selecting 0 will result in no delay feature. Note: “>” in front of a number indicates current selection. 3. Press the TRIP/RESET control switch for the next SETUP MENU item or wait for more than 4 seconds to return to the INFO MENU. Autolock This feature automatically locks all vehicle doors when the vehicle is shifted into any gear and when the vehicle is in motion over 13 mph (20
km/h) or higher. 1. To disable/enable the autolock feature, select this function from the SETUP MENU. 2. Press and hold the TRIP/RESET control switch to turn the autolock feature ON or OFF. 3. Press the TRIP/RESET control switch for the next SETUP MENU item or wait for more than 4 seconds to return to the INFO MENU. Autounlock This feature automatically unlocks all vehicle doors when the driver’s door is opened within 10 minutes of the ignition being turned off. 1. To disable/enable the autounlock feature, select this function from the SETUP MENU. 2. Press and hold the TRIP/RESET control switch to turn the autounlock ON or OFF. 3. Press the TRIP/RESET control switch for the next SETUP MENU item or wait for more than 4 seconds to return to the INFO MENU. Reverse Sensing System (Park Aid) (if equipped) This feature sounds a warning tone to warn the driver of obstacles near the rear bumper, and functions only when R (Reverse) gear is selected.81
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
1. To disable/enable the reverse sensing system feature with the vehicle in P (Park), select this function from the SETUP MENU or put the vehicle in R (Reverse). 2. Press and hold the TRIP/RESET control switch to turn the park aid ON or OFF. 3. Press the TRIP/RESET control switch for the next SETUP MENU item or wait for more than 4 seconds to return to the INFO MENU. Oil Life Start Value 1. Select this function from the SETUP MENU for the current display mode. 2. Press and hold the TRIP/RESET control switch to reset oil change. 3. Press the TRIP/RESET control switch for the next SETUP MENU item or wait for more than 4 seconds to return to the INFO MENU. Note: Oil Life Start Value of 100% equals 5,000 miles (8,000 km) and 180 days. Setting Oil Life Start Value to 60% sets the Oil Life Start Value to 3,000 miles (4,828 km) and 120 days. Compass display The compass heading is displayed as one of N, NE, E, SE, S, SW, W and NW in the message center display. The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in, on or near the vehicle may also affect compass accuracy. Usually, when something affects the compass readings, the compass will correct itself after a few days of operating your vehicle in normal conditions. If the compass still appears to be inaccurate, a manual calibration may be necessary. Refer to Compass zone adjustment. Most geographic areas (zones) have a magnetic north compass point that varies slightly from the northerly direction on maps. This variation is up to four degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones. A correct zone setting will eliminate this error. Refer to Compass calibration adjustment.
82
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
23
15
14
13
127 8 9 1011
Compass zone adjustment 1. Determine which magnetic zone you are in for your geographic location by referring to the zone map. 2. Turn ignition to the ON position.
3. Locate the reset button on top of the compass sensor mounted behind the mirror.
4. Press and hold the reset button on the compass module for approximately 4 seconds until COMPASS ZONE XX appears in the message center display. 5. Continue to press the reset button until the correct zone appears in the message center display. 6. After 4 seconds ZONE XX IS SET will appear in the message center display. 7. The display will return to normal operation. The zone is now updated. Compass calibration adjustment Perform compass calibration in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut.
83
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
1. Start the vehicle. 2. Locate the reset button on the compass sensor mounted on the base of mirror. 3. To calibrate, press and hold the reset button on the compass module for approximately eight seconds and release. 4. Slowly drive the vehicle in a circle (less than 5 km/h [3 mph]) until the CIRCLE SLOW TO CALIBRATE display changes to CALIBRATION COMPLETED. It will take up to five circles to complete calibration. 5. The compass is now calibrated.
System warnings System warnings alert you to possible problems or malfunctions in your vehicle’s operating systems. In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for 4
seconds. The message center will display the last selected feature if there are no more warning messages. This allows you to use the full functionality of the message center after you acknowledge the warning by pressing the RESET control and clearing the warning message. Warning messages are divided into four categories: • They cannot be cleared until the condition is corrected. • They will reappear on the display ten minutes from the reset if the • They will not reappear until an ignition OFF-ON cycle has been • They reappear if the condition clears then reoccurs within the samecondition has not been corrected.
completed.
ignition ON-OFF cycle.
This acts as a reminder that these warning conditions still exist within the vehicle.
84
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
Status Warning cannot be reset Warning returns after 10 minutes
Warning returns only after the ignition key is turned from OFF to ON.
Warning display Door ajar Check charging system Fuel level low Park brake engaged Check brake system Check park aid (if equipped) Low tire pressure Tire monitor fault Tire sensor fault Brake fluid level low Check headlamp Check highbeam lamp Check turn lamp Washer fluid level low Oil change required Engine oil change soon Liftgate/glass ajar
Warning returns after the condition has cleared then reoccures within the same ignition ON-OFF cycle. DOOR AJAR. Displayed when a door is not completely closed. CHECK CHARGING SYSTEM. Displayed when the electrical system is not maintaining proper voltage when the engine is running. If you are operating electrical accessories when the engine is idling at a low speed, turn off as many of the electrical loads as soon as possible. If the warning stays on or comes on when the engine is operating at normal speeds, have the electrical system checked as soon as possible. FUEL LEVEL LOW. Displayed as an early reminder of a low fuel condition. PARK BRAKE ENGAGED. Displayed when the manual park brake is set, the engine is running and the vehicle is driven more than 3 mph (5
km). If the warning stays on after the park brake is released, contact your authorized dealer as soon as possible. CHECK BRAKE SYSTEM. Displayed when the braking system is not operating properly. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible.85
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
CHECK PARK AID (if equipped). Displayed when the transmission is in R (Reverse) and the Reverse Sensing System (Park Aid) is disabled. Refer to Reverse Sensing System (Park Aid) in this section to enable. LOW TIRE PRESSURE. Displayed when one or more tires on your vehicle have low tire pressure. Refer to Inflating Your Tires in the Tires, Wheels and Loading chapter. TIRE MONITOR FAULT. Displayed when the Tire Pressure Monitoring System is malfunctioning. If the warning stays on or continues to come on, have the system inspected by your authorized dealer. TIRE SENSOR FAULT. Displayed when a tire pressure sensor is malfunctioning, or your spare tire is in use. For more information on how the system operates under these conditions, refer to Understanding Your Tire Pressure Monitoring System in the Tires, Wheels and Loading chapter. If the warning stays on or continues to come on, have the system inspected by your authorized dealer. BRAKE FLUID LEVEL LOW. Indicates the brake fluid level is low and the brake system should be inspected immediately. Refer to Brake fluid reservoir in the Maintenance and Specifications chapter. CHECK HEADLAMP. Displayed when the headlamps are activated and at least one bulb is burned out. Check the lamps as soon as possible and have the burned out lamp replaced. Refer to Replacing headlamp bulbs in the Lights chapter. CHECK HIGHBEAM LAMP. Displayed when the highbeam lamps are activated and at least one bulb is burned out. Check the lamps as soon as possible and have the burned out lamp replaced. Refer to Replacing headlamp bulbs in the Lights chapter. CHECK TURN LAMP. Displayed when the turn lamps are activated and at least one bulb is burned out. Check the lamps as soon as possible and have the burned out lamp replaced. Refer to Replacing headlamp bulbs in the Lights chapter. WASHER FLUID LEVEL LOW. Indicates the washer fluid reservoir is less than one quarter full. Check the washer fluid level. Refer to Windshield washer fluid in the Maintenance and Specifications chapter. OIL CHANGE REQUIRED. Displayed when the engine oil life remaining is 0%. An oil change is required whenever indicated by the message center and according to the recommended maintenance schedule. USE ONLY RECOMMENDED ENGINE OILS.
86
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
ENGINE OIL CHANGE SOON. Displayed when the engine oil life reaches 5% or less of the Oil Life Start Value. LIFTGATE/GLASS AJAR. Displayed when the liftgate or the liftgate glass is not completely closed.
OPTIONAL MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position, the message center, located on your instrument cluster, displays important vehicle information through a constant monitor of vehicle systems. You may select display features on the message center for a display of status. The system will also notify you of potential vehicle problems with a display of system warnings followed by an indicator chime.
Your display can show up to 6 reconfigurable telltales at one time. What ever is displayed in the top left corner has the highest priority.
87
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
Selectable features Reset Press the RESET control to select and reset functions shown in the INFO menu, SETUP menu, text warnings and reconfigurable telltale warnings.
Info menu The Info menu items are shown on the top two lines of the message center. Press the INFO control to display the following: • Trip odometer (Trip A and Trip B)• Distance to Empty • Average Fuel Economy • Instantaneous Fuel Economy • Fuel Used • Trip Elapsed Drive Time • Blank Trip odometer Refer to Gauges in the Instrument Cluster chapter. Distance to empty (DTE) Selecting this function from the INFO menu estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling to allow this feature to correctly detect the added fuel. The DTE function will display LOW FUEL LEVEL and sound a tone for one second when you have approximately 50 miles (80 km) to empty. If you RESET this warning message, this display and tone will return within 10 minutes.
88
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
service stations
DTE is calculated using a running average fuel economy, which is based on your recent driving history of 500 miles (800 km). This value is not the same as the average fuel economy display. The running average fuel economy is reinitialized to a factory default value if the battery is disconnected. Average fuel economy (AFE) Select this function from the INFO menu to display your average fuel economy in miles/gallon or liters/km. If you calculate your average fuel economy by dividing miles traveled by gallons of fuel used (liters of fuel used by 100 kilometers traveled), your figure may be different than displayed for the following reasons: • Your vehicle was not perfectly level during fill-up • Differences in the automatic shut-off points on the fuel pumps at • Variations in top-off procedure from one fill-up to another • Rounding of the displayed values to the nearest 0.1 gallon (liter) 1. Drive the vehicle at least 5 miles (8 km) with the speed control system engaged to display a stabilized average. 2. Record the highway fuel economy for future reference. It is important to press the RESET control (press and hold RESET for 2
seconds in order to reset the function) after setting the speed control to get accurate highway fuel economy readings. Instantaneous fuel economy Select this function from the INFO menu to display your instantaneous fuel economy. This will display your fuel economy as a Bar Graph ranging from to the bars increase from left to right, the instantaneous fuel economy is increasing. Your vehicle must be moving to calculate instantaneous fuel economy. When your vehicle is not moving, this function shows one or no bars illuminated. Instantaneous fuel economy cannot be reset.excellent fuel economy. As
poor fuel economy
89
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
Fuel Used Selecting this function from the INFO menu. “FUEL USED XXX.X GAL” will display the fuel used since last reset. The information displayed will be in gallons or liters, depending on English/Metric mode state.
Trip elapsed drive time Select this function from the INFO menu to display a timer. To operate the Trip Elapsed Drive Time perform the following: 1. Press and release RESET in order to start the timer. 2. Press and release RESET to pause the timer. 3. Press and hold RESET for 2 seconds in order to reset the timer to zero. Blank display Select this function from the INFO menu to turn the upper two lines of the message center display OFF. Setup menu Press the SETUP control twice for the following displays: • System Check • Units (English/Metric) • Language • Autolamp • Autolock • Autounlock • Easy Entry/Exit Seat • Park Aid (if equipped) • Compass Zone 90
SETUP
RESET
INFO
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
• Compass Calibration • Oil Life Start Value System check Selecting this function from the SETUP MENU causes the message center to cycle through each of the systems being monitored. For each of the monitored systems, the message center will indicate either an OK message or a warning message for two seconds. Pressing the RESET control cycles the message center through each of the systems being monitored. The sequence of the system check report and how it appears in the message center is as follows: 1. OIL LIFE RESET 2. CHARGING SYSTEM 3. WASHER FLUID 4. DOOR AJAR 5. EXTERIOR LAMP 6. BRAKE SYSTEM 7. PARK BRAKE 8. FUEL LEVEL 9. MILES TO EMPTY To reset the oil monitoring system to 100% after each oil change [approximately 5,000 miles (8,000 km) or 180 days] perform the following: • From the SETUP MENU enter SYSTEM CHECK to display “HOLD RESET IF NEW OIL”.
91
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls • Press and hold the RESET
control for more than 2 seconds. Oil life is set to 100% and “OIL CHANGE SET TO 100%” is displayed.
Note: To change oil life 100% miles value from 5,000 miles (8,000 km) and 180 days to another value, refer to the Oil Life Start Value selected from the SETUP MENU in this section. Units (English/Metric) 1. Select this function from the SETUP MENU for the current units to be displayed. 2. Press the RESET control to change from English to Metric. 3. Press the RESET control for the next SETUP MENU item or wait for more than 4 seconds to return to the INFO menu. Language Note: When entering the SETUP MENU and a non-English language has been selected, “PRESS RESET FOR ENGLISH” will be displayed to change back to English. 1. Select this function from the SETUP MENU for the current language to be displayed. 2. Press the RESET control to cycle the message center through each of the language choices to the desired language.
Selectable languages are English, Spanish, French, Japanese, or Arabic. 3. Press the RESET control for the next SETUP MENU item or wait for more than 4 seconds to return to the INFO menu. Autolamp This feature keeps your headlights on for up to three minutes after the ignition is switched off.
92
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
1. To change the delay time of the autolamp feature, select this function from the SETUP MENU. 2. Press the RESET control to select the new Autolamp delay time (in seconds) value of 0, 10, 20, 30, 60, 90, 120 or 180 and wraps back to 0. Selecting 0 will result in no delay feature. Note: “>” in front of a number indicates current selection. 3. Press the RESET control for the next SETUP MENU item or wait for more than 4 seconds to return to the INFO menu. Autolock This feature automatically locks all vehicle doors when the vehicle is shifted into any gear and when the vehicle is in motion over 13 mph (20
km/h) or higher. 1. To disable/enable the autolock feature, select this function from the SETUP MENU. 2. Press the RESET control to turn the autolock feature ON or OFF. 3. Press the RESET control for the next SETUP MENU item or wait for more than 4 seconds to return to the INFO menu. Autounlock This feature automatically unlocks all vehicle doors when the driver’s door is opened within 10 minutes of the ignition being turned off. 1. To disable/enable the autounlock feature, select this function from the SETUP MENU. 2. Press the RESET control to turn the autounlock ON or OFF. 3. Press the RESET control for the next SETUP MENU item or wait for more than 4 seconds to return to the INFO menu.93
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
Easy entry/exit seat This feature automatically moves the drivers seat backwards for easy exit from the vehicle. 1. To disable/enable the easy exit seat feature, select this function from the SETUP MENU. 2. Press the RESET control to turn the easy entry exit seat ON or OFF. 3. Press the RESET control for the next SETUP MENU item or wait for more than 4 seconds to return to the INFO menu. Reverse Sensing System (Park Aid) (if equipped) This feature sounds a warning tone to warn the driver of obstacles near the rear bumper, and functions only when R (Reverse) gear is selected. 1. To disable/enable the reverse sensing system feature with the vehicle in P (Park), select this function from the SETUP MENU or put the vehicle in R (Reverse). 2. Press the RESET control to turn the park aid ON or OFF. 3. Press the RESET control for the next SETUP MENU item or wait for more than 4 seconds to return to the INFO menu. Compass display The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in, on or near the vehicle may also affect compass accuracy. Usually, when something affects the compass readings, the compass will correct itself after a few days of operating your vehicle in normal conditions. If the compass still appears to be inaccurate, a manual calibration may be necessary. Refer to Compass zone/calibration adjustment.
94
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
Most geographic areas (zones) have a magnetic north compass point that varies slightly from the northerly direction on maps. This variation is four degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones. A correct zone setting will eliminate this error. Refer to Compass zone/calibration adjustment. Note: Compass zone and calibration adjustments can be entered by using the INFO and SETUP MENU controls or using the reset button on top of the compass sensor mounted behind the mirror. Compass zone adjustment 1. Determine your magnetic zone by referring to the zone map. 2. Turn ignition to the ON position. 3. Start the engine.
23
15
14
13
127 8 9 1011
95
4. From SETUP menu, select compass zone. 5. Press RESET control until the message center display changes to show the current zone setting (XX).
6. Press the RESET control repeatedly until the correct zone setting for your geographic location is displayed on the message center. The range of zone values are from 01 to 15 and “wraps” back to 01.
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
7. Wait 4 seconds when correct zone is chosen.
Compass calibration adjustment. Perform compass calibration in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut. 1. From the SETUP menu, press the SETUP control to select the compass calibration function. 2. Press RESET for calibration.
3. Slowly drive the vehicle in a circle (less than 3 mph [5 km/h]) until the CIRCLE SLOWLY TO CALIBRATE display changes to CALIBRATION COMPLETE. It will take up to five circles to complete calibration.
4. The compass is now calibrated.
96
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
Oil life Start Value 1. Select this function from the SETUP control for the current display mode. 2. Each press of the RESET control reduces the value by 10 percent. Note: Oil Life Start Value of 100% equals 5,000 miles (8,000 km) and 180 days. Setting Oil Life Start Value to 60% sets the Oil Life Start Value to 3,000 miles (4,828 km) and 120 days. System warnings System warnings alert you to possible problems or malfunctions in your vehicle’s operating systems. In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for 4
seconds. The message center will display the last selected feature if there are no more warning messages. This allows you to use the full functionality of the message center after you acknowledge the warning by pressing the RESET control and clearing the warning message. Warning messages are divided into four categories: • They cannot be cleared until the condition is corrected. • They will reappear on the display ten minutes from the reset if the • They will not reappear until an ignition OFF-ON cycle has been • They reappear if the condition clears then reoccurs within the samecondition has not been corrected.
completed.
ignition ON-OFF cycle.
This acts as a reminder that these warning conditions still exist within the vehicle.
97
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Status Warning cannot be reset Warning returns after 10 minutes
Warning returns only after the ignition key is turned from OFF to ON.
Driver Controls
Warning display Door ajar Check charging system Fuel level low Park brake engaged Check brake system Check park aid (if equipped) Low tire pressure Tire monitor fault Tire sensor fault Brake fluid level low Check headlamp Check highbeam lamp Check turn lamp Washer fluid level low Oil change required Engine oil change soon Liftgate/glass ajar
Warning returns after the condition has cleared then reoccures within the same ignition ON-OFF cycle. DOOR AJAR. Displayed when a door is not completely closed. CHECK CHARGING SYSTEM. Displayed when the electrical system is not maintaining proper voltage. If you are operating electrical accessories when the engine is idling at a low speed, turn off as many of the electrical loads as soon as possible. If the warning stays on or comes on when the engine is operating at normal speeds, have the electrical system checked as soon as possible. FUEL LEVEL LOW. Displayed as an early reminder of a low fuel condition. PARK BRAKE ENGAGED. Displayed when the manual park brake is set, the engine is running and the vehicle is driven more than 3 mph (5
km). If the warning stays on after the park brake is released, contact your authorized dealer as soon as possible. CHECK BRAKE SYSTEM. Displayed when the braking system is not operating properly. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible.98
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
CHECK PARK AID (if equipped). Displayed when the transmission is in R (Reverse) and the Reverse Sensing System (Park Aid) is disabled. Refer to Reverse Sensing System (Park Aid) in this section to enable. LOW TIRE PRESSURE. Displayed when one or more tires on your vehicle have low tire pressure. Refer to Inflating Your Tires in the Tires, Wheels and Loading chapter. TIRE MONITOR FAULT. Displayed when the Tire Pressure Monitoring System is malfunctioning. If the warning stays on or continues to come on, have the system inspected by your authorized dealer. TIRE SENSOR FAULT. Displayed when a tire pressure sensor is malfunctioning, or your spare tire is in use. For more information on how the system operates under these conditions, refer to Understanding Your Tire Pressure Monitoring System in the Tires, Wheels and Loading chapter. If the warning stays on or continues to come on, have the system inspected by your authorized dealer. BRAKE FLUID LEVEL LOW. Indicates the brake fluid level is low and the brake system should be inspected immediately. Refer to Brake fluid reservoir in the Maintenance and Specifications chapter. CHECK HEADLAMP. Displayed when the headlamps are activated and at least one bulb is burned out. Check the lamps as soon as possible and have the burned out lamp replaced. Refer to Replacing headlamp bulbs in the Lights chapter. CHECK HIGHBEAM LAMP. Displayed when the highbeam lamps are activated and at least one bulb is burned out. Check the lamps as soon as possible and have the burned out lamp replaced. Refer to Replacing headlamp bulbs in the Lights chapter. CHECK TURN LAMP. Displayed when the turn lamps are activated and at least one bulb is burned out. Check the lamps as soon as possible and have the burned out lamp replaced. Refer to Replacing headlamp bulbs in the Lights chapter. WASHER FLUID LEVEL LOW. Indicates the washer fluid reservoir is less than one quarter full. Check the washer fluid level. Refer to Windshield washer fluid in the Maintenance and Specifications chapter. OIL CHANGE REQUIRED. Displayed when the engine oil life remaining is 0%. An oil change is required whenever indicated by the message center and according to the recommended maintenance schedule. USE ONLY RECOMMENDED ENGINE OILS.
99
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
ENGINE OIL CHANGE SOON. Displayed when the engine oil life reaches 5% or less of the Oil Life Start Value. LIFTGATE/GLASS AJAR. Displayed when the liftgate or the liftgate glass is not completely closed.
POSITIVE RETENTION FLOOR MAT
Do not install additional floor mats on top of the factory installed floor mats as they may interfere with the accelerator or the
brake pedals.
Position the driver floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal. To remove the floor mat, reverse the installation procedure.
CARGO COVER (IF EQUIPPED) Your vehicle may be equipped with a cargo area cover that covers the luggage compartment of your vehicle. To install the cover: Push both ends of the cover into the depressions (right side first) in the trim panels behind the second row seat.
To reduce the risk of injuries, the cargo area
cover must be properly installed on the rear trim panels.
100
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
Do not place any objects on the cargo area cover. They may obstruct your vision or strike occupants of the vehicle in the
case of a sudden stop or collision.
Cargo management system The cargo management system consists of storage compartments located in the floor of the rear cargo area. 7 passenger stowage: 1. To open, lift up on handle and the lid. 2. To close, lower and press the lid down.
5 passenger stowage: When the lid is open, it will stand up on its own. 1. To open, lift the release handle and the lid. 2. To close, lower the lid, lift the release handle and press down on the lid.
REAR LIFTGATE The liftgate area is only intended for cargo, not passengers. You can open and close the liftgate from outside the vehicle. It cannot be opened from inside the cargo area.
101
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls • To open the liftgate window, press the control on the remote entry transmitter or, with the liftgate unlocked, push the control button on the right side under the license plate lamp shield.
• To open the liftgate, unlock the liftgate (with the power door locks, the remote entry or the keyless entry pad) and pull the middle lever under the license plate lamp shield.
To lock the liftgate and the liftgate window, use the power door locks or press the door lock switch on the left side of the cargo area. The liftgate door and window should be closed before driving. If not, possible damage may occur to your vehicle.
Always close liftgate window before opening liftgate. Liftgate glass and liftgate should never be open at the same time. Failure
to observe this warning may result in personal injury or damage to your vehicle.
Make sure the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle. This will also
reduce the risk of passengers and cargo falling out.
LUGGAGE RACK Your vehicle is equipped with a roof rack. The maximum recommended load is 100 lbs (45 kg), evenly distributed. Use the tie down loops on the thumbwheels (if equipped) to secure the load.
102
2006 Explorer (exp) Owners Guide (post-2002-fmt) USA (fus)
Driver Controls
To adjust cross-bar position (if equipped): 1. Loosen the thumbwheel at both ends of the cross-bar (both cross-bars are adjustable). 2. Slide the cross-bar to the desired location. 3. Tighten the thumbwheel at both ends of the cross-bar.
Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a
lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sport cars are designed to perform satisfactorily under off-road conditions. Avoid sharp turns, excessive speed and abrupt maneuvers in these vehicles. Failure to drive cautiously could result in an increase risk of loss of vehicle control, vehicle rollover, personal injury and death.
103
2006 Explorer (exp) Owners Guide (post-2002-fmt)
