2008 Dodge Dakota Owners Manual

N Plastic Grocery Bag Retainers . . . . . . . . . . . . . 144
m Rear Window Features . . . . . . . . . . . . . . . . . . . 145

N Rear Window Defroster – If Equipped . . . . . . . 145
N Sliding Rear Window – If Equipped . . . . . . . . 146
m Tailgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
. . . . . . . . . . . . . . . . . . . . . 146

N Tailgate Removal N Two Position Tailgate / Upper

Load Platform . . . . . . . . . . . . . . . . . . . . . . . 147
m Rear Cargo Area Utility Rails . . . . . . . . . . . . . . 149
m Slide-In Campers . . . . . . . . . . . . . . . . . . . . . . . 151
N Camper Applications . . . . . . . . . . . . . . . . . . . 151
N General Information . . . . . . . . . . . . . . . . . . . 151
N Carbon Monoxide Warning Vehicles Equipped

With A Cap Or Slide-In Campers . . . . . . . . . . 151

MIRRORS

Inside Day/Night Mirror The mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77

Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of truck). The mirror should be adjusted while set in the day position (toward windshield). Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. Exterior Mirrors Folding Feature — If Equipped Folding exterior mirrors are hinged and may be moved either forward or rearward to resist damage. Electric Remote-Control Mirrors The controls for the power mirrors are located on the driver’s door trim panel.

78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move. When finished adjusting the mirror, turn the control to the center position to prevent accidentally moving a mirror.

WARNING!

Vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side mirror.

HANDS–FREE COMMUNICATION (UConnectT) — IF EQUIPPED

NOTE: The sales code RER radio contains an inte- grated Hands-Free Communication (UConnectt) sys- tem. Refer to your “Navigation User’s Manual” for UConnectt system operating instructions for this radio.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79

UConnectt is a voice-activated, hands-free, in- vehicle communications system. UConnectt allows you to dial a phone number with your cellular phone using simple voice commands (e.g., 9Call” { “Mike” {”Work9 or 9Dial” { “248-555-12129). Your cellular phone’s audio is trans- mitted through your vehicle’s audio system; the system will automatically mute your radio when using the UConnectt system. NOTE: The UConnectt system use requires a cellular phone equipped with the Bluetooth 9Hands-Free Profile,9
version 0.96 or higher. See UConnectt website for sup- ported phones. NOTE: following web sites: † www.chrysler.com/uconnect † www.dodge.com/uconnect † www.jeep.com/uconnect

For UConnectt customer support, visit

the

80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

† or call 1–877–855–8400
UConnectt allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s micro- phone for private conversation. The UConnectt phone book enables you to store up to 32
names and four numbers per name. Each language has a separate 32-name phone book accessible only in that system is driven through your language. This Bluetooth™ Hands-Free phone. UConnectt features Bluetooth™ technology - the global standard that enables different electronic devices to con- nect to each other without wires or a docking station, so UConnectt works no matter where you stow your cellu- lar phone (be it your purse, pocket, or briefcase), as long as your phone is turned on and has been paired to the vehicle’s UConnectt system. The UConnectt system allows up to seven cellular phones to be linked to system.

cellular

profile

Only one linked (or paired) cellular phone can be used with the system at a time. The system is available in English, Spanish, or French languages (as equipped). Phone Button

The rearview mirror contains the microphone for the system (depending on the type of mirror and radio equipped), and either the radio or the mirror has the two control buttons (Phone Button and Voice Recognition Button) that will enable you to access the system. Voice Recognition Button

Actual button location may vary with radio. The individual buttons are described in the “Operation” section.

The UConnectt system can be used with any Hands-Free Profile See UConnectt website for supported phones. If your cellular

Bluetooth™ cellular

certified

phone.

phone supports a different profile (e.g., Headset Profile) you may not be able to use any UConnectt features. Refer to your cellular service provider or the phone manufac- turer for details. The UConnectt system is fully integrated with the vehi- cle’s audio system. The volume of the UConnectt system can be adjusted either from the radio volume control knob or from the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts from the UConnectt system such as 9CELL9 or caller ID on certain radios. Operation Voice commands can be used to operate the UConnectt system and to navigate through the UConnectt menu struc- ture. Voice commands are required after most UConnectt system prompts. You will be prompted for a specific com- mand and then guided through the available options.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81

† Prior to giving a voice command, one must wait for the beep, which follows the 9Ready9 prompt or another prompt. † For certain operations, compound commands can be used. For example, instead of saying 9Setup9 and then 9Phone Pairing,9 the following compound command can be said: 9Setup Phone Pairing.9
† For each feature explanation in this section, only the combined form of the voice command is given. You can also break the commands into parts and say each part of the command, when you are asked for it. For example, you can use the combined form voice com- mand 9Phonebook New Entry,9 or you can break the combined form command into two voice commands: 9Phonebook9 and 9New Entry.9 Please remember, the UConnectt system works best when you talk in a normal conversational tone, as if speaking to some one sitting eight feet away from you.

82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Voice Command Tree Refer to “Voice Tree” at the end of this section. Help Command If you need assistance at any prompt, or if you want to know your options at any prompt, say 9Help9 following the beep. The UConnectt system will play all the options at any prompt if you ask for help. To activate the UConnectt system from idle, simply press the “Phone” button and follow audible prompts for directions. All UConnectt system sessions begin with a press of the “Phone” button on the radio control head. Cancel Command At any prompt, after the beep, you can say 9Cancel9 and you will be returned to the main menu. However, in a few instances the system will take you back to the previous menu. Pair (Link) UConnectt System to a Cellular Phone To begin using your UConnectt system, you must pair your compatible Bluetooth™ enabled cellular phone.

To complete the pairing process, you will need to refer- ence your cellular phone owner’s manual. The UConnectt website may also provide detailed instruc- tions for pairing. The following are general phone to UConnectt System pairing instructions: † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say † When prompted, after the beep, say 9Pair a Phone9 and † You will be asked to say a four-digit pin number, which you will later need to enter into your cellular. You can enter any four-digit pin number. You will not need to remember this pin number after the initial pairing process.

follow the audible prompts.

9Setup Phone Pairing.9

† For identification purposes, you will be prompted to give the UConnectt system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. † You will then be asked to give your cellular phone a priority level between 1 and 7, 1 being the highest priority. You can pair up to seven cellular phones to your UConnectt system. However, at any given time, only one cellular phone can be in use, connected to your UConnectt System. The priority allows the UConnectt system to know which cellular phone to use if multiple cellular phones are in the vehicle at the same time. For example, if priority 3 and priority 5
phones are present in the vehicle, the UConnectt system will use the priority 3 cellular phone when you make a call. You can select to use a lower priority cellular phone at any time (refer to 9Advanced Phone Connectivity9).

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83

call.

9Dial.9

Dial by Saying a Number † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say † System will prompt you to say the number you want † For example, you can say 9234-567-8901.9 The phone number that you enter must be of valid length and combination. Based on the country in which the ve- hicle was purchased, the UConnectt limits the user from dialing invalid combination of numbers. For example, in USA, 234-567-890 is nine digits long, which is not a valid USA phone number - the closest valid phone number has ten digits. † The UConnectt system will confirm the phone num- ber and then dial. The number will appear in the display of certain radios.

84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

“Call.9

you want call.

Call by Saying a Name † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say † System will prompt you to say the name of the person † After the 9Ready9 prompt and the following beep, say the name of the person you want to call. For example, you can say 9John Doe,9 where John Doe is a previ- ously stored name entry in the UConnectt phone book. Refer to 9Add Names to Your UConnectt Phone- book,9 to learn how to store a name in the phone book. † The UConnectt system will confirm the name and then dial the corresponding phone number, which may appear in the display of certain radios.

9Phonebook New Entry.9

Add Names to Your UConnectt Phonebook NOTE: Adding names to phone book is recommended when vehicle is not in motion. † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say † When prompted, say the name of the new entry. Use of long names helps the voice recognition and it is recommended. For example, say 9Robert Smith9 or 9Robert9 instead of 9Bob.9
† When prompted, enter the number designation (e.g., 9Home,9 9Work,9 9Mobile,9 or 9Pager9). This will allow you to store multiple numbers for each phone book entry, if desired. † When prompted, recite the phone number for the

phone book entry that you are adding.

After you are finished adding an entry into the phone book, you will be given the opportunity to add more phone numbers to the current entry or to return to the main menu. The UConnectt system will allow you to enter up to 32
names in the phone book with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phone book accessible only in that language. Phonebook Download UConnectt allows the user to download entries from their phone via Bluetooth. To use this feature, press the “Phone” button and say “Phonebook Download.” Sys- tem prompts “Ready to accept vcard entry via Bluetooth…” The system is now ready to accept phone- book entries from your phone using the Bluetooth Object

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85

fers of phonebook entries to use this feature.

Exchange Profile (OBEX). Please see your phone owners’ manual for specific instructions on how to send these entries from your phone. NOTE: † Phone handset must support Bluetooth OBEX trans- † Some phones cannot send phonebook entries if they are already connected to any system via Bluetooth, and you may see a message on the phone display that the Bluetooth link is busy. In this case, the user must first disconnect or drop the Bluetooth connection to the UConnectt and then send the address book entry via Bluetooth. Please see your phone owners’ manual for specific instructions on how to drop the Bluetooth connection. † If the phonebook entry is longer than 24 characters it

will be use only the first 24 characters.

86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Edit Entries in the UConnectt Phonebook NOTE: Editing names in the phone book is recom- mended when vehicle is not in motion. † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say † You will then be asked for the name of the phone book † Next, choose the number designation (home, work, † When prompted, recite the new phone number for the

mobile, or pager) that you wish to edit.

entry that you wish to edit.

9Phonebook Edit.9

phone book entry that you are editing.

After you are finished editing an entry in the phone book, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu.

9Phonebook Edit9 can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may have a mobile and a home number, but you can add John Doe’s work number later using the 9Phonebook Edit9 feature. Delete Entries in the UConnectt Phonebook NOTE: Editing phone book entries is recommended when vehicle is not in motion. † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say † After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phone book entry that you wish to delete or you can say 9List Names9 to hear a list of the entries in the phone book from which you choose. To select one of the entries

9Phonebook Delete.9

from the list, press the 9Voice Recognition9 button while the UConnectt system is playing the desired entry and say 9Delete.9
† After you enter the name, the UConnectt system will ask you which designation you wish to delete, home, work, mobile, pager, or all. Say the designation you wish to delete. † Note that only the phone book entry in the current

language is deleted.

Delete All Entries in the UConnectt Phonebook † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say † The UConnectt system will ask you to verify that you

9Phonebook Erase All.9

wish to delete all the entries from the phonebook.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87

† After confirmation, the phone book entries will be † Note that only the phone book in the current language

deleted.

is deleted.

9Phonebook List Names.9

List All Names in the UConnectt Phonebook † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say † The UConnectt system will play the names of all the † To call one of the names in the list, press the 9Voice Recognition’ button during the playing of the desired name, and say 9Call.9

phone book entries.

NOTE: The user can also exercise 9Edit9 or 9Delete9
operations at this point.

88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

† The UConnectt system will then prompt you as to the number designation you wish to call. † The selected number will be dialed. Phone Call Features The following features can be accessed through the UConnectt system if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the UConnectt system. Check with your cellular service provider for the features that you have. Answer or Reject an Incoming Call - No Call Currently in Progress When you receive a call on your cellular phone, the UConnectt system will interrupt the vehicle audio sys- tem, if on, and will ask if you would like to answer the call. Press ’Phone’ button to accept the call. To reject the

call, press and hold the ’Phone’ button until you hear a single beep indicating that the incoming call was rejected. Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your cell phone. Press the ’Phone’ button to place the current call on hold and answer the incoming call. NOTE: The UConnectt system compatible phones in market today do not support rejecting an incoming call when another call is in progress. Therefore, the user can only either answer an incoming call or ignore it. Making a Second Call while Current Call in Progress To make a second call while you are currently in a call, press the ’Voice Recognition’ button and say 9Dial9 or 9Call9 followed by the phone number or phone book

entry you wish to call. The first call will be on hold while the second call is in progress. To go back to the first call, refer to 9Toggling Between Calls.9 To combine two calls, refer to 9Conference Call.9
Place/Retrieve a Call from Hold To put a call on hold, press the 8Phone’ button until you hear a single beep. This indicates that the call is on hold. To bring the call back from hold, press and hold the “Phone” button until you hear a single beep. Toggling Between Calls If two calls are in progress (one active and one on hold), press the “Phone” button until you hear a single beep indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at one time.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89

Conference Call When two calls are in progress (one active and one on hold), press and hold the “Phone” button until you hear a double beep indicating that the two calls have been joined into one conference call. Three-Way Calling To initiate three-way calling, press the “Voice Recogni- tion” button while a call is in progress and make a second phone call as described under 9Making a Second Call while Current Call in Progress.9 After the second call has established, press and hold the “Phone” button until you hear a double beep indicating that the two calls have been joined into one conference call. Call Termination To end a call in progress, momentarily press the “Phone” button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. If the active call is terminated by the far end, a call on

90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

hold may not become active automatically. This is cell phone dependent. To bring the call back from hold, press and hold the “Phone” button until you hear a single beep. Redial † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say † The UConnectt system will call the last number that

9Redial.9

was dialed on your cellular phone.

NOTE: This may not be the last number dialed from the UConnectt system. Call Continuation Call continuation is progression of a phone call on UConnectt system after the vehicle ignition key has been

switched to off. Call continuation functionality available on the vehicle can be any one of three types: † After ignition key is switched off, a call can continue on the UConnectt system either until the call ends or until the vehicle battery condition dictates cessation of the call on the UConnectt system and transfer of the call to the mobile phone. † After ignition key is switched to off, a call can continue on the UConnectt system for certain duration, after which the call is automatically transferred from the UConnectt system to the mobile phone.

† An active call

is automatically transferred to the

mobile phone after ignition key is switched to off.

UConnectT System Features

Language Selection To change the language that the UConnectt system is using, † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say the name of the language you wish to switch to (English, Espanol, or Francais, if so equipped). † Continue to follow the system prompts to complete

language selection.

After selecting one of the languages, all prompts and voice commands will be in that language. NOTE: After every UConnectt language change opera- tion, only the language specific 32-name phone book is usable. The paired phone name is not language specific and usable across all languages.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91

Emergency Assistance If you are in an emergency and the mobile phone is reachable: † Pick up the phone and manually dial the emergency

number for your area.

If the phone is not reachable and the UConnectt system is operational, you may reach the emergency number as follows: † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say 9Emergency9 and the UConnectt system will instruct the paired cellular phone to call the emergency num- ber. This feature is only supported in the USA.

NOTE: The emergency number dialed is based on the Country where the vehicle is purchased (911 for USA and Canada and 060 for Mexico). The number dialed may not be applicable with the available cellular service and area.

92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

The UConnectt system does slightly lower your chances of successfully making a phone call as to that for the cell phone directly. Your phone must be turned on and paired to the UConnectt system to allow use of this vehicle feature in emergency situations when the cell phone has network coverage and stays paired to the UConnectt system. Towing Assistance If you need towing assistance, † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say

9Towing Assistance.9

NOTE: The Towing Assistance number dialed is based on the Country where the vehicle is purchased (1-800- 528-2069 for USA, 1-877-213-4525 for Canada, 55-14-3454
for Mexico City and 1-800-712-3040 for outside Mexico City in Mexico).

Please refer to the 24-Hour “Towing Assistance” cover- age details in the Warranty information booklet and on the 24–Hour Towing Assistance Card. Paging To learn how to page refer to 9Working with Automated Systems.9 Paging works properly except for pagers of certain companies which time-out a little too soon to work properly with the UConnectt system. Voice Mail Calling To learn how to access your voice mail, refer to 9Working with Automated Systems.9
Working with Automated Systems This method is used in instances where one generally has to press numbers on the cellular phone keypad while navigating through an automated telephone system. You can use your UConnectt system to access a voice- mail system or an automated service, such as, paging

service or automated customer service. Some services require immediate response selection, in some instances, that may be too quick for use of UConnectt system. When calling a number with your UConnectt system that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can push the “Voice Recognition” button and say the sequence you wish to enter followed by the word 9Send.9 For example, if required to enter your pin number followed with a pound 3 7 4 6 #, you can press the “Voice Recognition” button and say 93 7 4 6 # Send.9 Saying a number, or sequence of numbers, followed by 9Send9 is also to be used to navigate through an automated customer service center menu structure and to leave a number on a pager. You can also send stored UConnectt phonebook entries as tones for fast and easy access to voicemail and pager entries. To use this feature, dial the number you wish to call and then press the “Voice Recognition” button and

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93

say “Send.” The system will prompt you to enter the name or number, say the name of the phonebook entry you wish to send. The UConnectt will then send the corresponding phone number associated with the phone- book entry as tones over the phone. NOTE: † You may not hear all of the tones due to cellular phone † Some paging and voicemail systems have system timeout settings too short that may not allow the use of this feature.

network configurations, this is normal.

Barge In - Overriding Prompts The “Voice Recognition” button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately. For example, if a prompt is playing 9Would you like to pair a phone, clear

94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

a{,9 you could press the “Voice Recognition” button and say 9Pair a Phone9 to select that option without having to listen to the rest of the voice prompt. Turning Confirmation Prompts On/Off Turning confirmation prompts off will stop the system from confirming your choices (e.g., the UConnectt sys- tem will not repeat a phone number before you dial it). † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say 9Setup Confirmations.9 The UConnectt system will play the current confirmation prompt status and you will be given the choice to change it. Phone and Network Status Indicators If available on the radio and/or on a premium display such as the instrument panel cluster, and supported by your cell phone, the UConnectt system will provide notification to inform you of your phone and network

status when you are attempting to make a phone call using UConnectt. The status is given for roaming, net- work signal strength, phone battery strength, etc. Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the UConnectt system (while dial- ing via the cell phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired Bluetooth™ cellular phone, the audio will be played through your vehicle’s audio system. The UConnectt system will work the same as if you dial the number using voice recognition. NOTE: Certain brands of mobile phones do not send the dial ring to the UConnectt system to play it on the vehicle audio system, so you will not hear it. Under this situation, after successfully dialing a number, the user

may feel that the call did not go through even though the call is in progress. Once your call is answered, you will hear the audio. Mute/Un-Mute (Mute Off) When you mute the UConnectt system, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the UConnectt system: † Press the “Voice Recognition” button. † Following the beep, say 9Mute.9
In order to un-mute the UConnectt system: † Press the “Voice Recognition” button. † Following the beep, say 9Mute-off.9

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95

Advanced Phone Connectivity

Transfer Call to and from Cellular Phone The UConnectt system allows on going calls to be transferred from your cellular phone to the UConnectt system without terminating the call. To transfer an ongo- ing call from your UConnectt paired cellular phone to the UConnectt system or vice-versa, press the “Voice Recognition” button and say 9Transfer Call.9
Connect or Disconnect Link Between the UConnectt System and Cellular Phone Your cellular phone can be paired with many different electronic devices, but can only be actively 9connected9
with one electronic device at a time. If you would like to connect or disconnect the Bluetooth™ connection between a UConnectt paired cellular phone and the UConnectt system, then follow the instruction described in your cellular phone user’s manual.

96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

“Setup Phone Pairing.”

List Paired Cellular Phone Names † Press the “Phone” button to begin. † After the “Ready” prompt and the following beep, say † When prompted, say 9List Phones.9
† The UConnectt system will play the phone names of all paired cellular phones in order from the highest to the lowest priority. To “select” or “delete” a paired phone being announced, press the “Voice Recogni- tion” button and say “Select” or “Delete.” Also, see the next two sections for an alternate way to “select” or “delete” a paired phone.

Select another Cellular Phone This feature allows you to select and start using another phone paired with the UConnectt system. † Press the “Phone” button to begin.

9Setup Select Phone9 and follow the prompts.

† After the 9Ready9 prompt and the following beep, say † You can also press the “Voice Recognition” button anytime while the list is being played, and then choose the phone that you wish to select. † The selected phone will be used for the next phone the call. UConnectt system will return to using the highest priority phone present in or near (approximately within 30 feet) the vehicle.

the selected phone is not available,

If

Delete UConnectt Paired Cellular Phones † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say † At the next prompt, say 9Delete9 and follow the

9Setup Phone Pairing.9

prompts.

† You can also press the “Voice Recognition” button anytime while the list is being played, and then choose the phone you wish to delete.

Things You Should Know About Your UConnectT System UConnectt Tutorial To hear a brief tutorial of the system features, press the “Phone” button and say “UConnectt Tutorial.” Voice Training For users experiencing difficulty with the system recog- nizing their voice commands or numbers, the UConnectt system Voice Training feature may be used. To enter this training mode, follow one of the two procedures: From outside the UConnectt mode (e.g. from radio mode) † Press and hold the “Voice Recognition” button for 5

seconds until the session begins, or,

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97

† Press the “Voice Recognition” button and say 9Setup,

Voice Training9 command.

Repeat the words and phrases when prompted by the UConnectt system. For best results, the Voice Training session should be completed when the vehicle is parked, engine running, all windows closed, and the blower fan switched off. This procedure may be repeated with a new user. The system will adapt to the last trained voice only. To restore the Voice Recognition system to factory default settings, enter the Voice Training session via the above procedure and follow the prompts. Voice Recognition (VR) † For best performance, adjust the rear view mirror to provide at least 1⁄2 inch (1 cm) gap between the overhead console (if equipped) and the mirror.

98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

† Always wait for the beep before speaking. † Speak normally, without pausing, just as you would speak to a person sitting approximately eight (8) feet away from you. † Make sure that no one other than you is speaking during a voice recognition period. † Performance is maximized under: † low-to-medium blower setting, † low-to-medium vehicle speed, † low road noise, † smooth road surface, † fully closed windows, † dry weather condition.

† Even though the system is designed for users speaking in North American English, French, and Spanish ac- cents, the system may not always work for some. † When navigating through an automated system, such as voice mail, or when sending a page, at the end of speaking the digit string, make sure to say 9Send.9
† Storing names in phone book when vehicle is not in † It is not recommended to store similar sounding † UConnectt phone book nametag recognition rate is optimized for the person who stored the name in the phone book. † You can say 9O9 (letter 9O9) for 909 (zero). 98009 must be

names in the UConnectt phone book.

motion is recommended.

spoken 9eight-zero-zero.9

† Even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported. † In a convertible vehicle, system performance may be

compromised with the convertible top down.

Far End Audio Performance † Audio quality is maximized under: † low-to-medium blower setting, † low-to-medium vehicle speed, † low road noise, † smooth road surface, † fully closed windows, and † dry weather condition. † operation from driver seat.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99

† Performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the UConnectt system. † Echo at far end can sometime be reduced by lowering † In a convertible vehicle, system performance may be

the in-vehicle audio volume.

compromised with the convertible top down.

Bluetooth Communication Link Cellular phones have been found to lose connection to the UConnectt system. When this happens, the connec- tion can generally be re-established by switching the phone off/on. Your cell phone is recommended to remain in Bluetooth 9on9 mode. Power-Up After switching the ignition key from OFF to either ON or ACC position, or after a language change, you must wait at least five (5) seconds prior to using the system.

100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101

102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Voice Commands

Alternate(s)

Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103

Voice Commands

Alternate(s)

Primary call cancel confirmation prompts. continue delete dial download edit emergency English erase all Espanol Francais help home

104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Voice Commands

Alternate(s)

pairing phone book

Primary language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing phonebook previous record again

Voice Commands

Alternate(s)

return or main menu select

phone settings or phone set up

Primary redial return to main menu select phone send set up

towing assistance transfer call UConnectt Tutorial try again voice training work yes

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105

General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: † This device may not cause harmful interference. † This device must accept any interference received, including interference that may cause undesired op- eration.

SEATS

Manual Seat Adjustment The adjusting lever is at the front of the seat, near the floor. Lift the lever and move the seat to the desired position. Release the bar to lock the seat into position. Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched.

106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.

Front Seats Manual Seat Recliners The front seats are equipped with recliners. The reclining mechanism is operated by a lever located on the right side of the passenger’s seat and the left side of the driver’s seat. To recline, lean forward slightly before lifting the lever, then push back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position. Using body pressure, lean forward and rearward on the seat to be sure the seatback is locked.

WARNING!

Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked.

Manual Lumbar Support Adjustment — If Equipped The manual lumbar support rotary control adjustment is located on the left side of the driver’s seat. Rotate the knob to increase or decrease the amount of lumbar support.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107

Adjustable Head Restraints — Front Seating Positions Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Pull up or push down on the restraints so that the upper edge is as high as practical, at least to the level of the ears.

108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To lower the head restraint, depress the release button located at the base of the head restraint and push down on the head restraint.

6 - Way Power Seat Adjuster — Driver’s Side Only The 6-way power seat adjuster switches are on the outboard side of the driver’s seat. Use this switch to move the seat up or down, forward or rearward, or tilt.

Power Seat Control Location

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109

The power seat controls are on the outboard side of the driver’s seat cushion. Three switches control the seat movement. The four-way switch in the center can be moved forward or backwards to get the most comfortable position. The same switch can be moved up and down to control seat height. Change the seat angle by using the two toggle switches, tilting it up or down.

Up, Down, Forward, and Rearward

Tilt Adjustment

110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Extended Cab/Crew Cab Rear Seat More cargo space is available by lifting up on the rear seat cushion. The Crew Cab rear seat is a 60/40 split cushion and full back. Either cushion can be raised independently. Heated Seats — If Equipped The heated seat switches are located on the center of the instrument panel. Press the desired switch once to obtain High heat level, then press the switch again to obtain Low heat level. A third button press will turn Off the heated seat. If you do not purposefully turn the switch Off, the seat heating level will automatically change to the next lower level, or Off. The High heat level operates for 30 minutes (ap- proximate), the Low heat level operates for 30 minutes (approximate). The heated seat will also turn Off when the ignition is turned Off. Both indicators On identifies High heat level. The lower indicator On identifies Low

heat level. Flashing indicator lights on the switch indicate that the Heated Seat system needs servicing.

WARNING!

Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat.

TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111

Then push the safety latch lever up while lifting the grille with your right hand. It is located at the bottom center of the grille. Lift the hood and gas filled props will hold it open.

Hood Release Lever Location

Secondary Latch Location

112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center front edge of the hood to ensure that both latches engage. Never drive your vehicle unless the hood is fully closed, with both latches engaged.

LIGHTS

WARNING!

If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are fully latched before driving.

Interior Lights

Courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the switch) is rotated to the second upward detent position, or if equipped, when the UNLOCK button is pressed on the key fob.When a door is open and the interior lights are on, rotating the dimmer

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113

control all the way down to the OFF detent will cause all the interior lights to go out. This is also known as the 9Party9 mode because it allows the doors to stay open for extended periods of time without discharging the vehi- cle’s battery. The brightness of the instrument panel lighting can be regulated by rotating the dimmer control up (brighter) or down (dimmer). When the headlights are ON you can supplement the brightness of the odometer, trip odom- eter, radio and overhead console by rotating the control up until you hear a click. This feature is termed the “Parade” mode and is useful when headlights are re- quired during the day. If the dimmer control is not in this position, the audio display may be difficult to read if the headlights are on during the daytime. Club Cab/Quad Cab models may have an optional switched dome lamp that may be operated by pressing the lens.

114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Battery Saver To protect the life of your vehicle’s battery, Load Shed- ding is provided for both the interior and exterior lights. If the ignition is off and any door is left ajar for 15
minutes or the dimmer control is rotated upwards for 15
minutes, the interior lights will automatically turn off. If the headlamps remain on while the ignition is cycled off, the exterior lights will automatically turn off after 8
minutes. If the headlamps are turned on and left on for 8
minutes while the ignition is off, the exterior lights will automatically turn off. NOTE: Battery Saver mode is cancelled if the ignition is ON.

Headlamp Delay To aid in your exit, your vehicle is equipped with a headlamp delay that will leave the headlamps on for 60
seconds. This delay is initiated when the ignition is turned OFF while the headlamp switch is on, and then the headlamp switch is cycled off. The headlamps will remain on for 60 seconds. Headlamp delay can be cancelled by either turning the headlamp switch ON then OFF or by turning the ignition ON. Headlights, Parking Lights, Panel Lights

When the headlight switch is rotated to the first position, the parking lights, taillights, side marker lights, license plate light and instrument panel lights are all turned on. The headlights will turn ON when the switch is rotated to the second position.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115

To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other abrasive materials to clean the lenses. Daytime Running Lights (Canada – Standard and US Fleet Vehicles – If Equipped) The headlights on your vehicle will illuminate when the engine is started, the transmission is out of the PARK position and the parking brake is released. This provides a constant 9Lights ON9 condition until the ignition is turned OFF. The lights illuminate at less than normal intensity. If the parking brake is applied or the transmis- sion is in the park position, the Daytime Running Lights will turn off.

Your vehicle is equipped with plastic headlight lenses that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.

116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Lights-on Reminder If the headlights, parking lights, courtesy lights or cargo lights are left on, after the ignition is turned off, a chime will sound when the driver’s door is opened. Fog Lights — If Equipped

The foglights are turned ON by placing the head- light rotary control in the parking light or head- light position and pressing on the headlight rotary control. The fog lights will operate only when the parking lights are ON or when the vehicle headlights are ON low beam. An indicator light located in the instrument cluster will illuminate when the fog lights are on. The fog lights will turn off when the switch is pressed a second time, also when the headlight switch is rotated to the OFF position, or the high beam is selected.

CARGO Light — If Equipped

The cargo lights are turned on by pressing on the CARGO button. The interior lights will also turn on when the cargo lights are on. The cargo lights will also turn on for 30 seconds when a key fob Unlock is pressed, as part of the illuminated entry feature.

Multifunction Control Lever The multifunction control lever is located on the left side of the steering column. Turn Signals

Move the lever up or down to signal a right-hand or left-hand turn.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117

The arrow on either side of the instrument cluster flashes to indicate the direction of the turn, and proper operation of the front and rear turn signal lights. If an indicator fails to light when the lever is moved, it would suggest that the switch or indicator lamp is defective. If a defective bulb or wiring circuit is detected for the turn signal system, the arrow indicators will flash at a faster rate. You can signal a lane change by moving the lever partially up or down. NOTE: duration, a continuous chime will sound. Turn Signal Auto-Mode Tap the multi-function control lever once and the turn signal (left or right) will flash 3 times, and automatically turn off.

If a turn signal has been left on for at least a mile

118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Passing Light You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer- ing wheel. This will cause the high beam headlights to turn on until the lever is released. High Beam / Low Beam Select Switch Pull the multifunction control lever fully toward the steering wheel to switch the headlights from HIGH or LOW beam.

WINDSHIELD WIPERS AND WASHERS The multifunction control lever is located on the left side of the steering column.

Windshield Wipers

The wipers and washers are operated by a switch in the multifunction control lever. Turn the end of the handle to select the desired wiper speed. Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle,

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119

with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range. The delay interval decreases as you rotate the knob until it enters the LO continual speed position. The delay can be regulated from a maximum of about 18 seconds between cycles, to a cycle every 2 seconds. The delay intervals will double in duration when the vehicle speed is 10 mph (16 km) or less.

WARNING!

Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during wind- shield washer use.

120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

If the front wiper is operating when the ignition NOTE: is turned off, the wiper will automatically return to the 9Park9 position. When the vehicle is restarted, the wipers will resume operation. Windshield Washers To use the washer, push in on the washer knob on the end of the multifunction control lever and hold while spray is desired. If the washer knob is depressed while in the delay range, the wiper will operate for several seconds after the washer knob is released. It will then resume the intermittent interval previously selected. If the washer knob is pushed, for a period greater than 1 second, while in the OFF position, the wiper will wipe approximately three wipes, after the wash knob is released.

To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers.

TILT STEERING COLUMN To tilt the column, pull rearward on the lever below the turn signal control and move the wheel up or down, as desired. Push the lever forward to lock the column firmly in place.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121

WARNING!

Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving.

ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over accelerator opera- tion at speeds greater than (refer to the table below for the speed for your specific engine). The controls are mounted on the steering wheel.

Tilt Steering Column Lever

122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

NOTE: The Electronic Speed Control System has been designed to shut down if multiple speed control switch buttons (i.e. SET and CANCEL) are operated simulta- neously in order to ensure proper operation. The system can be reactivated by pushing the speed control switch ON/OFF button and re-establishing the desired vehicle SET speed.

To Activate Push the ON/OFF button to the ON position. In the instrument cluster, the word “CRUISE” illuminates when the system is on. To Set At A Desired Speed When the vehicle has reached the desired speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed. To Deactivate A soft tap on the brake pedal, normal braking, or pressing the CANCEL button will deactivate speed control with- out erasing the memory. Pushing the ON/OFF button to the OFF position or turning off the ignition erases the memory.

WARNING!

Leaving the Speed Control ON when not in use is dangerous. You could accidentally set the system to cause it to go faster than you want. You could lose control and have an accident. Always leave the sys- tem OFF when you aren’t using it.

To Resume Speed To resume a previously set speed, push and release the RESUME button. Resume can be used at any speed above (refer to the table below for the speed for your specific engine). To Vary The Speed Setting When the speed control is on, speed can be increased by pressing and holding the ACCEL button. When the button is released, a new set speed will be established.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123

Tapping the ACCEL button once will result in a speed increase (refer to the table below for the speed for your specific engine). Each time the button is tapped, speed increases so that tapping the button three times will increase speed by three increments. Tapping the DECEL button once will result in a speed decrease (refer to the table below for the speed for your specific engine). Each time the button is tapped, speed will decrease. For example, tapping the button 3 times will decrease the speed by 3 times the speed listed in the table below (refer to the table below for the speed for your specific engine). To decrease speed while the speed control is on, press and hold the DECEL button. Release the button when the desired speed is reached, and the new speed will be set.

124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Functions Engage Speed Minimun RESUME Speed ACCEL Increase DECEL Decrease Dropout Speed To Accelerate For Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. NOTE: When driving uphill, at elevations above 2,000
feet (610 meters), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow below the SET speed. If the vehicle speed drops below (refer to the table below for the speed for your specific engine), the speed control will automatically disengage. If this hap- pens, you can push down on the accelerator pedal to maintain the desired speed.

All Engines 30 mph (48 km/h) 25 mph (40 km/h) 2 mph (3km/h) 1 mph (2 km/h) 25 mph (40 km/h) Vehicles equipped with a Automatic transmission may exhibit several downshifts under the above conditions. To reduce the frequency of the downshifts and to im- prove vehicle performance, it is advisable to lock out overdrive by pressing the “TOW/HAUL” button located at the end of the gear shifter.

WARNING!

Speed Control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125

OVERHEAD CONSOLE The overhead console has the following features:

† Courtesy Lights † Garage Door Opener — If Equipped † Compass/Temperature Mini-Trip Computer — If

Equipped

126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Courtesy/Reading Lights Near the front of the console are two courtesy/reading lights. Both lights illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (fully upward position), or when the UNLOCK button is pressed on the Remote Keyless Entry transmitter, if so equipped. These lights are also operated individually as reading lights by pressing the recessed area of the corresponding lens. NOTE: The courtesy/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. If the interior lights are left on after the vehicle is turned OFF, they will extinguish after 8 minutes.

COMPASS/TEMPERATURE MINI-TRIP COMPUTER This feature allows you to choose between a compass/ temperature display and one of four trip conditions being monitored. US/M Button Use this button to change the display from U.S. to metric measurement units.

RESET Button

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127

Global Reset If the RESET button and STEP button are pressed at the same time and held for 3 seconds the Global Reset feature will reset the distance to empty (using a default fuel economy value), trip odometer, and elapsed time displays.

fuel economy,

Use this button to reset the following displays: † Average Fuel Economy † Trip Odometer † Elapsed time.

128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Step Button

Use this button to choose or cycle through the four trip conditions.

Average Fuel Economy (AVG ECO) Shows the average fuel economy since the last reset. This display mode becomes less sensitive to instantaneous changes in fuel consumption as the number of total vehicle miles since the last reset increases. It is suggested that this mode be reset periodically for general operation or when driving conditions change significantly (for example, at the end of a trip or when a trailer is connected or disconnected). Distance To Empty (DTE) Shows the estimated distance that can be travelled with the fuel remaining in the tank. The estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. When Distance To Empty = LOW FUEL, the fuel gauge pointer will initially be on the red “E” marker. At this point (fuel gauge pointer on the the red “E” marker) there

is reserve fuel capacity, which corresponds to approxi- mately 8% of tank volume. This reserve capacity was put in place to prevent the likelihood of customers running out of fuel when operating at maximum load conditions in areas where there aren’t many gas stations. NOTE: The Distance To Empty will remain equal to zero, until the vehicle runs out of fuel or is refueled. Trip Odometer (ODO) This display shows the distance traveled since the last reset. Elapsed Time (ET) This display shows the accumulated ignition ON time since the last reset.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129

C/T Button

Use this button to select a readout of the outside tem- perature and one of eight compass headings that indicate the direction in which the vehicle is facing.

130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Compass/Temperature Display

WARNING!

Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage.

Automatic Compass Calibration This compass is self-calibrating which eliminates the need to manually set the compass. When the vehicle is new, the compass may appear erratic and the CAL symbol will be displayed.

After completing one 360° turn, with the vehicle traveling less than 5 mph (8 km/h), in an area free from large metal or metallic objects, the CAL symbol will turn off and the compass will function normally. Manual Compass Calibration

NOTE: To ensure proper compass calibration, make sure the compass variance is properly set before manu- ally calibrating the compass. If the compass appears erratic and the CAL symbol does not appear, you must manually put the compass into the “Calibration” mode.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131

To Put Into a Calibration Mode Turn on the ignition and set the display to “Compass/ Temperature.” Press and hold the RESET button to change the display between VAR (compass variance) and CAL (compass calibration) modes. When the CAL sym- bol is displayed complete one 360 degree turn in an area free from large metal objects or power lines. The CAL symbol will turn off and the compass will function normally. Compass Variance is the difference between magnetic north and geographic north. In some areas of the country, the difference between magnetic and geographic north is great enough to cause the compass to give false readings. If this occurs, the compass variance must be set according to the Compass Variance Map.

Compass Variance Map

132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press and hold the RESET button approximately five seconds. The last vari- ance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation. Outside Temperature Because the ambient temperature sensor is located un- derhood, engine temperature can influence the displayed temperature, therefore, temperature readings are slowly updated when the vehicle speed is below 20 mph (30
km/h) or during stop and go driving.

GARAGE DOOR OPENER — IF EQUIPPED HomeLinkt replaces up to three remote controls (hand held transmitters) that operate devices such as garage door openers, motorized gates, lighting, or home security systems. The HomeLinkt unit operates off of your vehi- cle’s battery. NOTE: HomeLinkt is disabled when the Vehicle Theft Alarm is active.

WARNING!

WARNING!

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133

Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features. Call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for safety information or assistance.

Vehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run your vehicle in the garage while training the transceiver. Exhaust gas can cause seri- ous injury or death.

Programming HomeLinkT

Before You Begin The Compass Mini-Trip Computer (CMTC) illuminates the HomeLinkt symbol (a house with an arrow inside it) along with 1, 2 or 3 indicators under it when a HomeLinkt button is pressed. Pay attention to the indicator(s), as they will flash at different rates, or remain solid during training. If you have not trained any of the HomeLinkt buttons, erase all channels before you begin training.

134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To do this, press and hold the two outside buttons for 20
seconds. Release the buttons when the indicators start to flash. It is recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLinkt for more efficient training and accurate transmission of the radio-frequency signal. Your vehicle should be parked outside of the garage while training. 1. Turn the ignition switch to the ON/RUN position. 2. Place the hand-held transmitter 1–3 inches (3–8 cm) from the HomeLinktbuttons while the HomeLinktdisplay in view. For optimal training, point the battery end of the hand- held transmitter away from the HomeLinkt.

keeping

3. Simultaneously press and hold both the chosen HomeLinktbutton and the hand-held transmitter button until the indicator(s) change from a slow to a rapid flash rate. Then release both the HomeLinkt and hand-held trans- mitter buttons. It may take up to 30 seconds, or longer in rare cases. The garage door may open & close while you train. If the signal is too weak to train, replace the battery in the original hand-held transmitter. NOTE: Some gate operators and garage door openers may require you to replace Step #3 with procedures noted in the “Gate Operator/Canadian Programming” section.

4. Press and hold the just-trained HomeLinkt button. If the indicator(s) blink rapidly for two seconds and then remains constant, continue with next section: Program- ming A Rolling Code System. NOTE: After training a HomeLinkt channel, if the garage door does not operate with HomeLinkt and the garage door opener was manufactured after 1995, the garage door opener may have rolling code. If so, proceed to the heading “Programming A Rolling Code System.” 5. PROGRAMMING A ROLLING CODE SYSTEM At the garage door opener motor (in the garage), locate the “learn” or “training” button. This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open & close the door).

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135

1 — Garage Door Opener 2 — Training Button 6. Firmly press and release the “learn” or “training” button. The name and color of the button may vary by manufacturer. NOTE: There are 30 seconds in which to initiate the next step after the “Learn” button has been pressed.

136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

7. Return to the vehicle and press the programmed HomeLinkt button twice (holding the button for 2 sec- onds each time). If the device is plugged in and activates, programming is complete. If the device does not activate, press the button a third time (for 2 seconds) to complete the training. If you are have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. To program the remaining two HomeLinkt buttons, repeat each step for each remaining button. DO NOT erase the channels. Gate Operator/Canadian Programming Canadian radio-frequency laws require transmitter sig- nals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLinkt to pick up the signal during programming.

Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner. It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. If you are having difficulties programming a garage door opener or a gate operator, replace “Programming HomeLink” Step 3 with the following: 3. Continue to press and hold the HomeLinktbutton while you press and release - every two seconds (“cycle”) until HomeLinkthas successfully accepted the frequency signal. The indicator(s) will change from a slow to rapid flash when trained. If you unplugged the device for training, plug it back in at this time.

transmitter

hand-held

your

Then proceed with Step 4 under “Programming HomeLink.” earlier in this section. Using HomeLinkT To operate, simply press and release the programmed HomeLinkt button. Activation will now occur for the trained device (i.e. garage door opener, gate operator, security system, entry door lock, home/office lighting, etc. The hand-held transmitter of the device may also be used at any time. Reprogramming a Single HomeLinkT Button To re-program a channel trained, follow these steps: 1. Turn the ignition switch to the ON/RUN position. 2. Press and hold the desired HomeLinktbutton for 20
seconds until the indicator(s) starts to flash. Do not release the button.

that has been previously

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137

3. Without releasing the button, proceed with PRO- GRAMMING HOMELINK Step #2 and follow all remain- ing steps. Security It is advised to erase all channels before you sell or turn in your vehicle. To do this, press and hold the two outside buttons for 20
seconds until the indicators begin to flash. Note that all channels will be erased. Individual channels cannot be erased. The HomeLinkt Universal Transceiver is disabled when the Vehicle Theft Alarm is active. Troubleshooting Tips If you are having trouble programming HomeLinkt, here are some of the most common solutions: † Replace the battery in the original transmitter.

138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

† Press the Learn Button on the Garage Door Opener to † Did you unplug the device for training, and remember

complete the training for Rolling Code.

to plug it back in?

If you are have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. General Information This device complies with FCC rules part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2. This device must accept any interference that may be received including interference that may cause undesired operation

NOTE: The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compli- ance could void the user’s authority to operate the device. The term “IC:” before the certification/registration num- ber only signifies that Industry Canada technical specifi- cations were met.

ELECTRICAL POWER OUTLETS This vehicle has two 12V auxiliary power outlets that can provide up to 20 Amps of current for accessories de- signed for use with standard power outlet adapters. The outlets are located in the instrument panel, below the temperature control setting knob, and the other inside the full - size center console. When the optional Cigar Lighter heating element is used, it heats when pushed in and

pops out automatically when ready for use. To preserve the heating element, do not hold the lighter in the heating position. The instrument panel outlet can be reconfigured by the customer to operate only when the ignition is On (switch battery fed) or with the ignition switch On/Off (battery fed) to allow for cellular phone charging and/or opera- tion while the ignition is Off. This can be done by moving the power outlet (switchable) fuse (fuse #22) from the inboard position to the outboard position. NOTE: All accessories connected to these outlets should be removed or turned OFF when the vehicle is not in use to protect the battery against discharge (unless the cus- tomer has reconfigured the fuse block to switched battery feed).

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139

Electrical Outlet Use With Engine OFF (Battery Fed Configuration)

CAUTION!

† Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. † Accessories that draw higher power (i.e. coolers, vacuum cleaners, lights, etc.), will discharge the battery even more quickly. Use these only inter- mittently and with greater caution. † After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the generator to recharge the vehicle’s battery.

140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

FLOOR CONSOLE — IF EQUIPPED

Floor Console Features The Floor Console between the driver’s and front pas- senger’s seat has the following features: † Miscellaneous storage compartments † 3 cup holders (2 are removable) † iPod/Phone storage bin † 12 Volt power outlet inside storage compartment † Side open armrest lid † Tissue holder & 2 pen holders † Coin slots The coin slots are located under the instrument panel center stack.

Storage Compartments Some miscellaneous storage compartments and cup holders are both removable and dishwasher safe for cleaning purposes (upper rack of dishwasher only). Vari- ous storage compartments provide versatile and useful storage. A coin holder is also provided inside the driver side storage bin. Power Outlet and Portable Phone Storage The console is equipped with a power outlet and an iPod/ phone storage bin. The phone storage bin can be used when easy access to the phone is needed. Also, the power outlet inside console compartment can be used to charge the phone while it is being stored in the bin. The power outlet may be used for any portable item with a standard 12 volt power plug. Side Open Armrest Lid Pressing the button on the left side of the console opens the console armrest lid. The armrest lid will remain open

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141

CUP HOLDERS If your vehicle has bucket seats with a center console, there are three cup holders located on the console. Refer to the section on floor console. A two-cavity cup holder is available on all Crew Cab with rear seats mounted on the floor.

until armrest lid is closed manually by pressing the lid back into place. Two pen holders are provided on the inside of the armrest lid. A tissue holder is also provided on the inside of the armrest lid, which holds a pocket size soft pack of tissue.

CENTER STORAGE COMPARTMENT — IF EQUIPPED The center portion of the seat folds down to provide an armrest with unique storage compartments under the lid. Push the button on the armrest to raise the lid. Compart- ments include a holder which will accommodate five compact disks with finger notches for easier access, a pencil tray, a coin holder, and a large open area for miscellaneous items.

Front Cup Holders – Crew Cab with Automatic

142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Rear Cup Holders – Crew Cab with Automatic

REAR STORAGE – IF EQUIPPED

Rear Convenience Storage Crates

WARNING!

Do not sit or stand on this crate. It may collapse causing serious injury.

The rear convenience storage crates are located under the rear seat lower cushion and consist of two removable, collapsible storage crates.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143

CAUTION!

Do not lift up on the “End Flaps” to open the crate, damage to the “End Flaps” may occur.

NOTE: The maximum loading capacity for the 40% crate is 30 lbs. and 50 lbs. for the 60% crate. To open the storage crate, lift upwards on the crate handles, and engage the crate end flaps. To remove the crate, press on the release lever and lift up on the crate.

Open Crate

1 - Crate Handles 2 - Crate End Flaps 3 - Release Lever

144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Plastic Grocery Bag Retainers Retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab.

Insert Crate

To install the crate into the base, insert the crate into the inboard slot and push down on the outboard side of the crate and snap into place. To collapse the crate, push the crate end flaps inward to disengage. Push the sides inward and snap into the base.

Grocery Bag Retainers

REAR WINDOW FEATURES

Rear Window Defroster – If Equipped

CAUTION!

Use care when washing the inside of the rear window to prevent damage to heating elements. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Also, keep all objects a safe distance from the window to prevent damaging the heating elements.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145

A push-button type switch is located on the right side of the control below the A/C (Snowflake) button. Pressing the switch will turn on the Rear Window Defroster. A light above the Rear Window Defroster symbol will illuminate to indicate the Rear Window Defroster is On. Pushing the button again will turn the Rear Window Defroster Off prior to the time-out. The Rear Window Defroster will turn off automatically after 15 minutes after the first push, 10 minutes after the second push all within the same ignition cycle. To prevent excessive battery drain, use the rear defroster only when the engine is running.

146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Sliding Rear Window – If Equipped

TAILGATE

Tailgate Removal To simplify mounting a camper unit with an overhang, the tailgate can be removed quickly. Follow these steps: 1. Open the tailgate to a 45° angle. 2. Unclip and remove the cables from the box while maintaining a 45° angle.

Sliding Rear Window Latch

A locking device in the center of the window helps to prevent entry from the rear of the vehicle. Squeeze the lock to release the window.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147

2. Hold the tailgate at a 45° angle and insert it into the passenger side pivot. 3. Clip the cables to the box. Two Position Tailgate / Upper Load Platform Your tailgate can be opened to the full open or the partial open position. The partial open position is for loading objects longer than the length of the bed (sheets of plywood, etc.) by creating an upper load platform: 1. Install lumber † Place lumber across the box in the indentations provided above the wheel housings and in the bulkhead dividers to form the floor. There are indents in the sheet metal (or bed liner if equipped) on the inner side of the box in front (Club Cab only) and behind both wheel housings.

3. Lift the tailgate off of the pivot on the passenger side by pulling upward and rearward at the same time. 4. Slide the tailgate to the passenger side while making sure clearance from the box and taillight is maintained. To reinstall the tailgate, do the following: 1. Slide the tailgate onto the driver’s side pivot.

148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

2. Secure the tailgate in the partially open position: † Open the tailgate slightly. † Snap the tailgate support cable between the cable guide and the tailgate bumper. Do this on both sides of the tailgate.

To return the tailgate to the full open position: † Lift up on the tailgate. † Remove both cables from between the cable guides

and the tailgate bumpers and lower the tailgate.

CAUTION!

† Care should always be exercised when operating a vehicle with cargo. Vehicle speeds may need to be reduced. Severe turns or rough roads may cause shifting or bouncing of the cargo that may result in vehicle damage. † Insure the load is securely tied down and is properly identified according to local laws if it extends beyond the taillamps. † LOADING should not exceed 400 lbs (181 kg) of material suspended above the wheelhouse and partially open tailgate or vehicle damage may result.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149

REAR CARGO AREA UTILITY RAILS

CAUTION!

The maximum load per cleat should not exceed 320
lbs (145 kg) and the angle of the load on each cleat should not exceed 60 degrees above horizontal, or damage to the cleat or cleat rail may occur.

There are four adjustable cleats that can be used to assist in securing cargo. Each cleat must be located and tight- ened down in one of the detentes, located on either rail, in order to keep cargo properly secure. To move the cleat to any position on the rail, turn the nut counterclockwise approximately three turns. Then pull out on the cleat and slide it to the detent nearest the desired location. Make sure the cleat is seated in the detent and tighten the nut.

150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To remove the cleats from the utility rail, remove the end cap by pushing up on the locking tab, located on the bottom of the end cap. Slide the cleat off the end of the rail.

Utility Rail

1 - Utility Rail Cleat 2 - Cleat Retainer Nut 3 - Utility Rail Detent

Utility Rail End Cap

SLIDE-IN CAMPERS

Camper Applications Certain truck models are not recommended for slide-in campers. To determine if your vehicle is excluded, please refer to the Consumer Information Truck-Camper Load- ing document located in your Owner’s Manual packet or available from your dealer. For safety reasons, follow all instructions on this important document. General Information The Manufacturer’s Warranty does not apply to body modifications and special equipment, such as a camper unit, heaters, stoves, refrigerators, etc., supplied by manufacturers other than the manufacturer. For warranty coverage and service on these items, contact the appli- cable manufacturer.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151

To mount a camper unit with an overhang, the tailgate can be removed. Unlatch tailgate and remove support cables from the retainer pins. Raise right side of tailgate until the lower right side pivot clears the hanger bracket. Then slide the tailgate to the right to remove. Carbon Monoxide Warning Vehicles Equipped With A Cap or Slide-In Campers To avoid inhaling carbon monoxide, which is deadly, the exhaust system on vehicles equipped with “Cap or Slide-In Campers” should extend beyond the overhang- ing camper compartment and be free of leaks.

INSTRUMENT PANEL AND CONTROLS

CONTENTS

m Instruments And Controls . . . . . . . . . . . . . . . . . 156
m Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . 157
m Instrument Cluster Description . . . . . . . . . . . . . 158
m Electronic Digital Clock . . . . . . . . . . . . . . . . . . 167
N Clock Setting Procedure . . . . . . . . . . . . . . . . . 168
m Radio General Information . . . . . . . . . . . . . . . . 168
N Radio Broadcast Signals . . . . . . . . . . . . . . . . . 168
N Two Types Of Signals . . . . . . . . . . . . . . . . . . 169
N Electrical Disturbances . . . . . . . . . . . . . . . . . . 169

N AM Reception . . . . . . . . . . . . . . . . . . . . . . . 169
N FM Reception . . . . . . . . . . . . . . . . . . . . . . . . 169

m Sales Code RES — AM/FM Stereo Radio With

CD Player (MP3 AUX Jack) . . . . . . . . . . . . . . . . 170
N Operating Instructions - Radio Mode . . . . . . . 170
N Operation Instructions - CD Mode For CD

And MP3 Audio Play . . . . . . . . . . . . . . . . . . 176
N Notes On Playing MP3 Files . . . . . . . . . . . . . 178
N List Button (CD Mode For MP3 Play) . . . . . . . 181
N Info Button (CD Mode For MP3 Play) . . . . . . . 181

154 INSTRUMENT PANEL AND CONTROLS

m Sales Code REQ — AM/FM Stereo Radio

And 6–Disc CD/DVD Changer (MP3/WMA AUX Jack) . . . . . . . . . . . . . . . . . . 182
N Operating Instructions - Radio Mode . . . . . . . 183
N Operation Instructions - (Disc Mode For CD

And MP3/WMA Audio Play, DVD-Video) . . . . 190
N Notes On Playing MP3/WMA Files . . . . . . . . 192
N List Button (Disc Mode For

MP3/WMA Play)

. . . . . . . . . . . . . . . . . . . . . 195

N Info Button (Disc Mode For

MP3/WMA Play)

. . . . . . . . . . . . . . . . . . . . . 195

m Sales Code RER — Multimedia System — If

Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
N Operating Instructions — Satellite Radio . . . . . 199

N Operating Instructions — Hands-Free

Communication (UConnect™) (If Equipped)

. . 199
N Clock Setting Procedure . . . . . . . . . . . . . . . . . 199

m Satellite Radio (RSC) — If Equipped

(RER/REQ/REN Radios Only) . . . . . . . . . . . . . 201
N System Activation . . . . . . . . . . . . . . . . . . . . . 201
N Electronic Serial Number/Sirius Identification

Number (ENS/SID) . . . . . . . . . . . . . . . . . . . . 202
N Selecting Satellite Mode . . . . . . . . . . . . . . . . . 202
N Satellite Antenna . . . . . . . . . . . . . . . . . . . . . . 202
N Reception Quality . . . . . . . . . . . . . . . . . . . . . 203
N Operating Instructions - Satellite Mode . . . . . . 203
N Operating Instructions - Hands Free Phone

(If Equipped)

. . . . . . . . . . . . . . . . . . . . . . . . 205

N Operating Instructions - Video Entertainment

System (VES™) (If Equipped) . . . . . . . . . . . . . 206
m Remote Sound System Controls — If Equipped . . 206
N Radio Operation . . . . . . . . . . . . . . . . . . . . . . 207
N CD Player . . . . . . . . . . . . . . . . . . . . . . . . . . 207
m Compact Disc Maintenance . . . . . . . . . . . . . . . . 207
m Sound Box Operation . . . . . . . . . . . . . . . . . . . . 208

INSTRUMENT PANEL AND CONTROLS 155

m Radio Operation And Cellular Phones . . . . . . . . 209
m Climate Controls . . . . . . . . . . . . . . . . . . . . . . . 209
N Air Conditioning And Heater . . . . . . . . . . . . . 210
N Operating Tips . . . . . . . . . . . . . . . . . . . . . . . 213
N Operation Tips Chart . . . . . . . . . . . . . . . . . . . 215

156 INSTRUMENT PANEL AND CONTROLS

INSTRUMENTS AND CONTROLS

1 — Headlight Switch 2 — Air Outlets 3 — Demister Outlets 4 — Instrument Cluster 5 — Airbags

6 — Glove Box 7 — Radio 8 — Climate Controls 9 — Power Outlet 10 — Heated Seat Switches*

11 — Transfer Case Switch* 12 — Speed Control Switches 13 — Hood Release 14 — Parking Brake Release * If Equipped

INSTRUMENT CLUSTER

INSTRUMENT PANEL AND CONTROLS 157

158 INSTRUMENT PANEL AND CONTROLS

INSTRUMENT CLUSTER DESCRIPTION

1. Fuel Gauge

The fuel gauge shows level of fuel in tank when ignition switch is in the ON position.

2. Temperature Gauge

The temperature gauge indicates engine coolant temperature. Any reading within the normal range indicates that the cooling system is operat- ing satisfactorily. The gauge needle will likely indicate a higher temperature when driving in hot weather, up mountain grades, in heavy traffic, or when towing a trailer. If the needle rises to the “H” mark, stop the vehicle, shift into N (Neutral), and increase engine speed for 2-3 minutes. If the temperature reading does not return to normal, seek authorized service immediately.

CAUTION!

Do not leave your vehicle unattended with the en- gine running as you would not be able to react to the temperature indicator if the engine overheats.

The gauge pointer will remain near its last reading when the engine is turned off. It will return to a true reading when the engine is restarted. 3. Turn Signal Indicators When a turn signal is activated, a right-pointing or left-pointing arrow lights up and flashes to indicate the direction of the turn. These indicators also indicate proper operation of the front and rear turn signal lights. If either indicator flashes at a faster rate than normal, check for a defective bulb. If either indicator fails to light up when the lever is moved, check for a defective fuse or turn signal LED. A single chime is activated when the

left/right turn signal is left on with the engine RPM vehicle speed greater than 15 mph (24 km/h) for more than one mile. 4. Low Fuel Warning Light