Login- Download PDF Manual
-
and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the Fall and Spring. Apply a small amount of a high quality lubricant such as MOPAR威 Lock Cylinder Lubricant directly into the lock cylinder. Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accumula- tions of salt or road film.
MAINTAINING YOUR VEHICLE 431
Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield. Avoid using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Windshield Washers/Headlight Washers — If Equipped The windshield washer and the headlight washer (if equipped) share the same fluid reservoir. The fluid reservoir is located in the front of the engine compart- ment. Be sure to check the fluid level in the reservoir at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water.
432 MAINTAINING YOUR VEHICLE
When refilling the washer fluid reservoir, apply some washer fluid to a cloth or towel and wipe the wiper blades clean. This will help blade performance. To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers. The fluid reservoir will hold nearly 1 gal (4 L) of washer fluid when the message “Low Washer Fluid” appears in the Electronic Vehicle Information Center (EVIC) (if equipped).
WARNING!
Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution.
Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition,
inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required.
CAUTION!
MAINTAINING YOUR VEHICLE 433
WARNING!
Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to “Exhaust Gas” under “Safety Tips” in Section 2.
The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions control device. Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage.
Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the vehicle.
NOTE: systems can result against you.
Intentional tampering with emissions control in civil penalties being assessed
434 MAINTAINING YOUR VEHICLE
WARNING!
A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn.
In unusual situations involving grossly malfunctioning engine operation, a scorching odor may indicate severe and abnormal catalyst overheating. If this should occur, safely bring the vehicle to a complete stop, shut the engine OFF, and allow the vehicle to cool. Thereafter, obtain service, including a tune-up to manufacturer’s specifications immediately.
To minimize the possibility of catalyst damage: • Do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the • Do not idle the engine with any spark plug wires disconnected or removed, such as when diagnostic testing, or for prolonged periods during very rough idling or malfunctioning operating conditions.
vehicle.
Cooling System
WARNING!
• When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the LOCK position. The fan is tempera- ture controlled and can start at any time the ignition switch is in the ON position. • You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot.
Coolant Checks Check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If the engine coolant (antifreeze) is dirty or
MAINTAINING YOUR VEHICLE 435
rusty in appearance, the system should be drained, flushed, and refilled with fresh coolant. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser. Check the coolant recovery bottle tubing for brittle rub- ber, cracking, tears, cuts, and tightness of the connection at the bottle and radiator. Inspect the entire system for leaks. With the engine at normal operating temperature (but not running), check the cooling system pressure cap for proper vacuum sealing by draining a small amount of engine coolant (antifreeze) from the radiator drain cock. If the cap is sealing properly, the engine coolant (anti- freeze) will begin to drain from the coolant recovery bottle. DO NOT REMOVE THE COOLANT PRESSURE CAP WHEN THE COOLING SYSTEM IS HOT.
436 MAINTAINING YOUR VEHICLE
Cooling System — Drain, Flush, and Refill If the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old engine coolant (antifreeze) solution. Refer to the “Maintenance Schedule” in Section 8 for proper maintenance intervals. Selection of Coolant Use only the manufacturer’s recommended engine cool- ant (antifreeze). Refer to “Fluids, Lubricants, and Genu- ine Parts” in this section for the correct fluid type.
CAUTION!
• Mixing of engine coolant (antifreeze) other than specified HOAT engine coolant (antifreeze), may result in engine damage and may decrease corro- sion protection. If a non-HOAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, it should be replaced with the specified engine coolant (antifreeze) as soon as possible. • Do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use addi- tional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant (antifreeze) and may plug the radiator.
(Continued)
CAUTION! (Continued)
• This vehicle has not been designed for use with (anti- propylene glycol-based engine coolant freeze). Use of propylene glycol-based engine coolant (antifreeze) is not recommended.
Adding Coolant Your vehicle has been built with an improved engine coolant (antifreeze) that allows extended maintenance intervals. This engine coolant (antifreeze) can be used up to five years or 102,000 miles (170 000 km) before replacement. To prevent reducing this extended mainte- nance period, it is important that you use the same engine coolant (antifreeze) throughout the life of your vehicle. Please review these recommendations for using Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze).
MAINTAINING YOUR VEHICLE 437
When adding engine coolant (antifreeze): • The manufacturer
recommends using MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology). • Mix a minimum solution of 50% HOAT engine coolant (antifreeze) and distilled water. Use higher concentra- tions (not to exceed 70%) if temperatures below ⫺34°F (⫺37°C) are anticipated. • Use only high purity water such as distilled or deion- ized water when mixing the water/engine coolant (antifreeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system.
Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated.
438 MAINTAINING YOUR VEHICLE
NOTE: Mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifreeze) and will require more frequent engine coolant (antifreeze) changes. Cooling System Pressure Cap The cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery bottle. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces.
WARNING!
• The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle. Personal injury or en- gine damage may result.
Disposal of Used Coolant Used ethylene glycol-based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by ani- mals or children, do not store ethylene glycol-based engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately. Coolant Level The coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine OFF and cold, the level of the coolant in the bottle should be between the ranges indicated on the bottle. The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for
MAINTAINING YOUR VEHICLE 439
engine coolant (antifreeze) freeze point or replacing en- gine coolant (antifreeze). Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to Remember NOTE: When the vehicle is stopped after a few miles (kilometers) of operation, you may observe vapor coming from the front of the engine compartment. This is nor- mally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vapor- ized when the thermostat opens, allowing hot engine coolant (antifreeze) to enter the radiator.
440 MAINTAINING YOUR VEHICLE
If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant recovery bottle. • Check engine coolant (antifreeze) freeze point in the radiator and in the coolant recovery bottle. If engine coolant (antifreeze) needs to be added, contents of coolant recovery bottle must also be protected against freezing. • If frequent engine coolant (antifreeze) additions are required, or if the level in the coolant recovery bottle does not drop when the engine cools, the cooling system should be pressure tested for leaks. • Maintain engine coolant (antifreeze) concentration at 50% HOAT engine coolant (antifreeze) (minimum) and distilled water for proper corrosion protection of your engine, which contains aluminum components.
• Make sure that the radiator and coolant recovery bottle overflow hoses are not kinked or obstructed. • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean, also. • Do not change the thermostat for Summer or Winter install operation. If replacement is ever necessary, ONLY the correct type thermostat. Other designs may result in unsatisfactory engine coolant (antifreeze) performance, poor gas mileage, and increased emissions.
Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Refer to the “Maintenance Schedule” in Section 8 for proper maintenance intervals.
WARNING!
Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You wouldn’t have your full braking capacity in an emergency.
Master Cylinder - Brake Fluid Level Check Check the fluid level in the master cylinder immediately if the brake system warning light indicates system fail- ure. Check the fluid level in the master cylinder when per- forming underhood services. Clean the top of the master cylinder area before removing the cap. Add fluid to bring the level up to the top of the “FULL” mark on the side of the master cylinder reservoir.
MAINTAINING YOUR VEHICLE 441
Add enough fluid to bring the level up to the require- ments described on the brake fluid reservoir. With disc brakes, fluid level can be expected to fall as the brake pads wear. However, low fluid level may be caused by a leak and a checkup may be needed. Use only manufacturer’s recommended brake fluid. Re- fer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type.
WARNING!
• Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. • Use of a brake fluid that may have a lower initial boiling point, or is unidentified as to specification, may result in sudden brake failure during hard prolonged braking. You could have an accident.
442 MAINTAINING YOUR VEHICLE
Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter or moisture.
CAUTION!
Do not allow petroleum-based fluid to contaminate the brake fluid. Seal damage may result.
Automatic Transmission
Fluid Level Check Regular automatic transmission fluid level checks are not required. For this reason, the dipstick is omitted. If you notice fluid loss or gear shift malfunction, have your authorized dealer check the transmission fluid level.
CAUTION!
• Using a transmission fluid other than the manu- facturer’s recommended fluid may cause deterio- ration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than that recommended by the manufacturer will result in more frequent fluid and filter changes. Refer to “Fluids, Lubricants, and Genu- ine Parts” in this section for the correct fluid type. • The fluid level is preset at the factory and it does not require adjustment under normal operating conditions. If a transmission fluid leak occurs, visit your authorized dealer immediately. Severe damage to the transmission may occur. Your au- thorized dealer has the proper tools to adjust the fluid level accurately.
Fluid and Filter Changes Refer to the “Maintenance Schedule” in Section 8 for proper maintenance intervals. If the transmission is disassembled for any reason, the fluid and filter should be changed. Selection of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission perfor- mance. Use only manufacturer’s recommended transmis- sion fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid. No chemical flushes should be used in any transmission; only the approved lubricant may be used.
MAINTAINING YOUR VEHICLE 443
Special Additives Automatic Transmission Fluid (ATF) is an engineered product and its performance may be impaired by supple- mental additives. Therefore, do not add any fluid addi- tives to the transmission. The only exception to this policy is the use of special dyes to aid in detecting fluid leaks. In addition, avoid using transmission sealers as they may adversely affect seals. All Wheel Drive (AWD) — If Equipped The all wheel drive system consists of a transfer case and front differential. The exterior surface of these compo- nents should be inspected for evidence of fluid leaks. Confirmed leaks should be repaired as soon as possible. The transfer case fluid fill/inspection plug is located in the middle of the rear housing. To inspect the transfer case fluid level, remove the fill/inspection plug. The fluid level should be even with the bottom of the hole. Use this plug to add fluid as required.
444 MAINTAINING YOUR VEHICLE
The front differential fill plug is located on the outer cover near the halfshaft attachment. To inspect the differ- ential fluid level, remove the fill plug. The fluid level should be even with or slightly below the bottom of the hole. Fluid Changes Refer to the “Maintenance Schedule” in Section 8 for proper maintenance intervals. Appearance Care and Protection from Corrosion
Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and chemicals that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle. Outside parking, which exposes your vehicle to airborne contami- nants, road surfaces on which the vehicle is operated,
extreme hot or cold weather and other extreme condi- tions will have an adverse effect on paint, metal trim, and underbody protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • Road salt, dirt, and moisture accumulation. • Stone and gravel impact. • Insects, tree sap, and tar. • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants.
Washing • Wash your vehicle regularly. Always wash your ve- hicle in the shade using MOPAR威 Car Wash or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar, or other similar deposits have accumu- lated on your vehicle, use MOPAR威 Super Kleen Bug and Tar Remover to remove. • Use MOPAR威 Cleaner Wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.
MAINTAINING YOUR VEHICLE 445
CAUTION!
Do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces.
Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open. • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner.
446 MAINTAINING YOUR VEHICLE
• If your vehicle is damaged due to an accident or similar cause, which destroys the paint and protective coating, have your vehicle repaired as soon as pos- sible. The cost of such repairs is considered the respon- sibility of the owner. • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider • Use MOPAR威 Touch Up Paint or equivalent on scratches as soon as possible. Your authorized dealer has touch up paint to match the color of your vehicle.
mud or stone shields behind each wheel.
Wheel and Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome plated wheels should be cleaned regularly with a mild soap and water to prevent corrosion. To remove
heavy soil and/or excessive brake dust, use MOPAR威 Wheel Cleaner (05066247AB) or equivalent or select a nonabrasive, non-acidic cleaner. Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Only MOPAR威 or equivalent is recommended. Do not use oven cleaner. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective finish. Interior Care Use MOPAR威 Fabric Cleaner or equivalent to clean fabric upholstery and MOPAR威 Carpet Cleaner for carpeting. Interior Trim should be cleaned starting with a damp cloth, or MOPAR威 Satin Select. Do not use harsh cleaners or Armorall. Use MOPAR威 Total Clean to clean vinyl upholstery. MOPAR威 Total Clean is specifically recommended for leather upholstery.
Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and MOPAR威 Total Clean or equivalent. Care should be taken to avoid soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, detergents, or ammonia-based cleaners to clean your leather upholstery. Application of a leather condi- tioner is not required to maintain the original condition.
WARNING!
Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm.
MAINTAINING YOUR VEHICLE 447
Cleaning Headlights Your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses. Glass Surfaces All glass surfaces should be cleaned on a regular basis with MOPAR威 Glass Cleaner or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear win- dow equipped with electric defrosters or the right rear
448 MAINTAINING YOUR VEHICLE
quarter window equipped with the radio antenna. Do not use scrapers or other sharp instrument that may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag or micro-fiber towel. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue.
Seat Belt Maintenance Do not bleach, dye, or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use MOPAR威 Total Clean, a mild soap solution, or lukewarm water. Do not remove the belts from the vehicle to wash them. Replace the belts if they appear frayed or worn or if the buckles do not work properly. Cleaning the Center Console Cupholders Clean with a damp cloth or towel using a mild detergent with the cupholder in the center console. NOTE: The cupholder cannot be removed.
FUSES
Integrated Power Module The Integrated Power Module (IPM) is located in the engine compartment. This module contains fuses and relays.
Integrated Power Module
MAINTAINING YOUR VEHICLE 449
CAUTION!
• When installing the integrated power module cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the integrated power module and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system over- load. If a properly rated fuse continues to blow, it indicates a problem in the circuit that must be corrected.
450 MAINTAINING YOUR VEHICLE
Cav- ity
Cartridge Fuse —
—
—
—
— —
— —
—
Mini- Fuse 15 Amp Blue 25 Amp Neutral 25 Amp Neutral 25 Amp Neutral — 25 Amp Neutral — 25 Amp Neutral —
Description
Washer Motor
Powertrain Control Mod- ule (PCM) Ignition Run/Start
Alternator/EGR Solenoid
— Ignition Coils/Injectors/ Short Runner Valve — Starter
—
Cav- ity 10
11
12
13
14
1516
17
18Cartridge Fuse 30 Amp Pink 30 Amp Pink
40 Amp Green 50 Amp Red
— 50 Amp Red — — —
Mini- Fuse —
Description
Windshield Wiper
—
—
—
— —
— — —
Anti-Lock Brake System (ABS) Valves - If Equipped Radiator Fan
Anti-Lock Brake System (ABS) Pump Motor - If Equipped — Radiator Fan
— — —
Description
Mini- Fuse — — — —
Cartridge Fuse — — — —
Cav- ity 19
20
21
22
Rear Power Distribution Center There is also a power distribution center located in the trunk under the spare tire access panel. This center contains fuses and relays.— — — —
MAINTAINING YOUR VEHICLE 451
Opening The Access Panel
452 MAINTAINING YOUR VEHICLE
Rear Power Distribution Center
CAUTION!
• When installing the power distribution center cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system over- load. If a properly rated fuse continues to blow, it indicates a problem in the circuit that must be corrected.
Cav- ity
Cartridge Fuse 60 Amp Yellow 40 Amp Green — 40 Amp Green 30 Amp Pink —
—
Mini- Fuse —
—
— —
—
20 Amp Yellow 15 Amp Blue
Description
Ignition Off Draw (IOD)
Integrated Power Module (IPM) — Integrated Power Module (IPM) Heated Seats - If Equipped Fuel Pump
Rear Heated Seats - If Equipped
MAINTAINING YOUR VEHICLE 453
Cav- ity
Cartridge Fuse —
Mini- Fuse 15 Amp Blue
—
10
— 11 * — 12 * — 13 * — 14
—15
16
—
—
20 Amp Yellow — — — — 10 Amp Red
20 Amp Yellow —
Description
Diagnostic Link Connec- tor (DLC)/Wireless Con- trol Module (WCM)/ Wireless Ignition Node (WIN) Power Outlet
— — — — AC Heater Control/ Cluster/Security Module - If Equipped Trailer Tow Brake Mod- ule - If Equipped —
454 MAINTAINING YOUR VEHICLE
Cav- ity 17
Cartridge Fuse —
18
19
20
21
22
23
24
25
26
27—
—
— — — — — — — —
Mini- Fuse 20 Amp Yellow 20 Amp Yellow 10 Amp Red — — — — — — — 10 Amp Red
Description
Cluster
Cav- ity 28
Cartridge Fuse —
Selectable Power Outlet
29
—
Stop Lights
— — — — — — — Occupant Restraint Con- troller (ORC)
30
31
32
33
34—
— — — —
Mini- Fuse 10 Amp Red 5 Amp Orange
10 Amp Red
— — — —
Description
Ignition Run
Adaptive Cruise Control (ACC) - If Equipped/ Cluster/Electronic Stabil- ity Program (ESP) - If Equipped/Powertrain Control Module (PCM)/ STOP LIGHT Switch Door Modules/Power Mirrors/Steering Control Module (SCM) — — — —
Cav- ity 35
Cartridge Fuse —
36
37
38
—
—
—
Mini- Fuse 5 Amp Orange
20 Amp Yellow
15 Amp Blue 10 Amp Red
39
—
10 Amp Red
Description
Antenna Module - If Equipped/Power Mirrors/Rain Sensor - If Equipped Hands-Free Phone - If Equipped/Video Monitor - If Equipped/Radio Transmission
Analog Clock/Cargo Light/Satellite Receiver (SDARS) Video - If Equipped/Vehicle Infor- mation Module - If Equipped Heated Mirrors - If Equipped
MAINTAINING YOUR VEHICLE 455
Cav- ity 40
Cartridge Fuse —
41
—
Mini- Fuse 5 Amp Orange
10 Amp Red
42
43
44
30 Amp Pink 30 Amp Pink 20 Amp Blue
—
—
—
Description
Auto Inside Rearview Mirror - If Equipped/ Heated Seats - If Equipped/Switch Bank AC Heater Control/ Headlights/Park Assist - If Equipped/Tire Pres- sure Monitoring - If Equipped/Occupant Re- straint Controller (ORC) Front Blower Motor
Rear Window Defroster
Amplifier - If Equipped/ Sunroof - If Equipped
456 MAINTAINING YOUR VEHICLE
* Cavities 11, 12, and 13 contain self-resetting fuses (circuit breakers) that are only serviceable by an autho- rized dealer. The cluster, the driver seat switch (if equipped), and the memory module (if equipped) are fused by the 25-Amp circuit breaker in Cavity 11. The passenger seat switch (if equipped) is fused by the 25-Amp circuit breaker in Cavity 12. The door modules, the driver power window switch, and the passenger power window switch are fused by the 25-Amp circuit breaker in Cavity 13. If you experience temporary or permanent loss of these systems, see your authorized dealer for service.
VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days, you may want to take these steps to protect your battery. • Disconnect the negative cable from the battery.
• Anytime you store your vehicle, or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting. This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.
REPLACEMENT BULBS
Interior Bulb Number Rear Courtesy/Reading Lights. . . . . . . . . . . . . . W5W Rear Compartment (Trunk) Light . . . . . . . . . . . . . 562
Overhead Console Reading Lights. . . . . . . . . . . . . 578
Visor Vanity Lights . . . . . . . . . . . . . . . . . . . . . A6220
Glove Box Light . . . . . . . . . . . . . . . . . . . . . . . . . 194
Door Courtesy . . . . . . . . . . . . . . . . . . . . . . . . . . 562
Shift Indicator Light . . . . . . . . . . . . . . . . . JKLE14140
Optional Door Map Pocket / Cupholder Lighting . . . . . . . . LED (Serviced at Authorized Dealer)NOTE: For lighted switches, see your authorized dealer for replacement instructions. All of the interior bulbs are glass wedge base or glass cartridge types. Aluminum base bulbs are not approved and should not be used for replacement.
Bulb Number Exterior (300 Models) Low Beam Headlight . . . . . . . . . . . . . . . . . . . . . 9006
High Beam Headlight. . . . . . . . . . . . . . . . . . . . . 9005
Front Park/Turn Light . . . . . . . . . . . . . . . . . . . . 3157
Front Inner Park Light . . . . . . . . . . . . . . . . . . 194NA Front Outer Park Light . . . . . . . . . . . . . . . . . . 194NA Front Fog Light—If Equipped. . . . . . . . . . . . 9145/H10
(Serviced at Authorized Dealer) Front Sidemarker . . . . . . . . . . . . . . . . . . . . . . . W5W (Serviced at Authorized Dealer) Tail/Stop/Turn Light . . . . . . . . . . . . . . . . . . . . . 3057
Rear Sidemarker . . . . . . . . . . . . . . . . . . . . . . . . . 194
Backup Light. . . . . . . . . . . . . . . . . . . . . . . . . . . 3057MAINTAINING YOUR VEHICLE 457
Center High Mount Stop Light (CHMSL) . . . . . . . LED (Serviced at Authorized Dealer) License. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Exterior (300C Models) Bulb Number Low Beam Headlight (Standard Halogen). . . . . 9006XS Low Beam Headlight – High Intensity Discharge (HID) . . . . . . . . . . D1S (Serviced at Authorized Dealer) High Beam Headlight. . . . . . . . . . . . . . . . . . . . . 9005
Front Park/Turn Light . . . . . . . . . . . . . . . . . . 3157AK Front Fog Light. . . . . . . . . . . . . . . . . . . . . . 9145/H10
(Serviced at Authorized Dealer) Front Sidemarker . . . . . . . . . . . . . . . . . . . . . . . W5W (Serviced at Authorized Dealer) Tail/Stop Light . . . . . . . . . . . . . . . . . . . . . . . . . 3057
Tail Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3057
Turn Signal Light. . . . . . . . . . . . . . . . . . . . . . . 3757A Backup Light. . . . . . . . . . . . . . . . . . . . . . . . . . . 3057458 MAINTAINING YOUR VEHICLE
Center High Mount Stop Light (CHMSL) . . . . . . . LED (Serviced at Authorized Dealer) Outside Mirror Turn Signal & Approach Lights . . . . . . . . . . LED (Serviced at Authorized Dealer) License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . W5W
BULB REPLACEMENT
Low Beam Headlight, High Beam Headlight, Park/Turn Light, Inner Park Light, and Outer Park Light – 300 Models
1. Open the hood. NOTE: Removal of the air cleaner filter housing may be necessary prior to replacing bulbs in the headlight assem- bly on the driver side of the vehicle. 2. Twist the appropriate bulb and socket assembly coun- terclockwise, and then pull it out of the headlight assem- bly.
3. Disconnect the bulb from the socket assembly and install the replacement bulb. 4. Reinstall the bulb and socket assembly into the head- light assembly, and then turn it clockwise.
1 — High Beam Headlight Bulb 2 — Low Beam Headlight Bulb
MAINTAINING YOUR VEHICLE 459
3 — Park/Turn Light Bulb
4 — Inner Park Light Bulb 5 — Outer Park Light Bulb
460 MAINTAINING YOUR VEHICLE
CAUTION!
WARNING!
Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol.
Low Beam Headlight, High Beam Headlight, and Park/Turn Light – 300C
High Intensity Discharge Headlights (HID) — If Equipped The headlights are a type of high voltage discharge tube. High voltage can remain in the circuit even with the headlight switch off and the key removed. Because of this, you should not attempt to service a headlight bulb yourself. If a headlight bulb fails, take your vehicle to an authorized dealer for service.
A transient high tension occurs at the bulb sockets of HID headlights when the headlight switch is turned ON. It may cause serious electrical shock or electro- cution if not serviced properly. See your authorized dealer for service.
NOTE: On vehicles equipped with HID Headlights, when the headlights are turned on, there is a blue hue to the lights. This diminishes and becomes more white after approximately 10 seconds, as the system charges.
Backup Light, Side Marker Light, and Tail/Stop Turn Light — 300 Models
1. Open the Trunk. 2. Remove two fasteners from the back of the tail light assembly.
MAINTAINING YOUR VEHICLE 461
4. Remove the remaining fastener from the back of the tail light assembly. 5. Push the electrical connector locking tab to the side. 6. Disconnect the electrical connector.
3. Pull back the trunk liner.
7. Pull the tail light assembly clear from the vehicle to access the bulbs.
462 MAINTAINING YOUR VEHICLE
8. Turn the appropriate bulb and socket assembly coun- terclockwise to remove it from the tail light assembly.
1 — Backup Light Bulb
2 — Side Marker Light Bulb
MAINTAINING YOUR VEHICLE 463
9. Disconnect the bulb from the socket assembly and install the replacement bulb. 10. Reinstall the bulb and socket assembly into the tail light assembly, and then turn it clockwise. 11. Reinstall the tail light assembly, fasteners, electrical connector, and trunk liner. 12. Close the trunk.
3 — Tail/Stop/Turn Light Bulb
464 MAINTAINING YOUR VEHICLE
Tail/Stop, Tail, Turn Signal Light, and Backup Light — 300C Models
1. Open the Trunk. 2. Remove two fasteners from the back of the tail light assembly.
4. Remove the remaining fastener from the back of the tail light assembly. 5. Push the electrical connector locking tab to the side. 6. Disconnect the electrical connector.
3. Pull back the trunk liner.
7. Pull the tail light assembly clear from the vehicle to access the bulbs. Turn bulb sockets counterclockwise to remove. 8. Turn the appropriate bulb and socket assembly coun- terclockwise to remove it from the tail light assembly.
MAINTAINING YOUR VEHICLE 465
2 — Tail Light Bulb
1 — Tail/Stop Light Bulb
466 MAINTAINING YOUR VEHICLE
3 — Turn Signal Light Bulb
4 — Backup Light Bulb
9. Disconnect the bulb from the socket assembly and install the replacement bulb. 10. Reinstall the bulb and socket assembly into the tail light assembly, and then turn it clockwise.
MAINTAINING YOUR VEHICLE 467
11. Reinstall the tail light assembly, fasteners, electrical connector, and trunk liner. 12. Close the trunk. License Light
1. Remove the screws securing the light to the rear fascia. 2. Remove the bulb and socket assembly. 3. Disconnect the bulb from the socket assembly and install the replacement bulb.
1 — License Light Bulb 2 — Socket
4. Reinstall the bulb and socket assembly. 5. Reattach the light to the rear fascia, and then install the screws.
468 MAINTAINING YOUR VEHICLE
FLUIDS AND CAPACITIES
Fuel (Approximate) 2.7 Liter Engine 3.5 Liter Engine without All Wheel Drive 3.5 Liter Engine with All Wheel Drive 5.7 Liter Engine Engine Oil with Filter 2.7 Liter Engine (SAE 5W-20, API Certified) 3.5 Liter Engine (SAE 10W-30, API Certified) 5.7 Liter Engine (SAE 5W-20, API Certified)
U.S.
18 Gallons 18 Gallons 19 Gallons 19 Gallons
6.0 Quarts 6.0 Quarts 7.0 Quarts
Metric
68 Liters 68 Liters 72 Liters 72 Liters
5.7 Liters 5.7 Liters 6.6 Liters
Cooling System * 2.7 Liter Engine (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) 3.5 Liter Engine without All Wheel Drive (MOPAR威 Antifreeze/ Coolant 5 Year/100,000 Mile Formula) 3.5 Liter Engine with All Wheel Drive (MOPAR威 Antifreeze/Coolant 5
Year/100,000 Mile Formula) 5.7 Liter Engine without Severe Duty II Cooling System (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) 5.7 Liter Engine with Severe Duty II Cooling System (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) * Includes heater and coolant recovery bottle filled to MAX level.MAINTAINING YOUR VEHICLE 469
9.9 Quarts
11.1 Quarts
11.4 Quarts
14.7 Quarts
15.1 Quarts
9.4 Liters
10.5 Liters
10.8 Liters
13.9 Liters
14.3 Liters
470 MAINTAINING YOUR VEHICLE
FLUIDS, LUBRICANTS, AND GENUINE PARTS
Engine Component Engine Coolant
Engine Oil (2.7L Engine)
Engine Oil (3.5L Engine)
Engine Oil (5.7L Engine)
Spark Plugs (2.7L Engine) Spark Plugs (3.5L Engine) Spark Plugs (5.7L Engine)
Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395. Refer to the engine oil fill cap for cor- rect SAE grade. Use API Certified SAE 10W-30 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395. Refer to the engine oil fill cap for cor- rect SAE grade. Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395. Refer to the engine oil fill cap for cor- rect SAE grade. TE10MCC5 (Gap 0.050 in [1.27 mm]) ZFR5LP–13G (Gap 0.050 in [1.27 mm]) LZFR5C–11 (Gap 0.043 in [1.1 mm])
Component Oil Filter (2.7L, 3.5L, and 5.7L En- gines) Fuel Selection (2.7L Engine) Fuel Selection (3.5L and 5.7L En- gines) Chassis Component Automatic Transmission Brake Master Cylinder
Power Steering Reservoir
Front Axle Rear Axle Transfer Case
MAINTAINING YOUR VEHICLE 471
Fluid, Lubricant, or Genuine Part MOPAR威 Engine Oil Filter (P/N 04884899AB) or equivalent
87 Octane 87 Octane Acceptable — 89 Octane Recommended
Fluid, Lubricant, or Genuine Part MOPAR威 ATF+4 Automatic Transmission Fluid MOPAR威 DOT 3 and SAE J1703 should be used or equivalent. If DOT 3
brake fluid is not available, then DOT 4 is acceptable. Use only recom- mended brake fluids. MOPAR威 Power Steering Fluid + 4, MOPAR威 ATF+4 Automatic Transmis- sion Fluid API GL-5 SAE 75W90 Synthetic Gear Lubricant or equivalent API GL-5 SAE 75W140 Synthetic Gear Lubricant or equivalent MOPAR威 (P/N 68049954AA) BW 44–40 Transfer Case LubricantMAINTENANCE SCHEDULES
CONTENTS
䡵 Emissions Control System Maintenance . . . . . . 474
䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . 474▫ Required Maintenance Intervals . . . . . . . . . . 476
M
474 MAINTENANCE SCHEDULES
EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services in- cluded in this manual, should be done to provide best vehicle performance and reliability. More frequent main- tenance may be needed for vehicles in severe operating conditions, such as dusty areas and very short trip driving. Inspection and service should also be done anytime a malfunction is suspected. NOTE: Maintenance, replacement or repair of the emis- sions control devices and systems on your vehicle may be performed by any automotive repair establishment or individual using any automotive part that has been certified pursuant to U.S. EPA or in the State of Califor- nia, California Air Resources Board regulations.
Information Center
MAINTENANCE SCHEDULE The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. On Electronic Vehicle (EVIC) equipped vehicles, “Oil Change Required” will be dis- played in the EVIC and a single chime will sound, indicating that an oil change is necessary. On Non-EVIC equipped vehicles, “Change Oil” will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary. Based on engine operation conditions, the oil change indicator message will illuminate. This means that ser- vice is required for your vehicle. Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).
NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change, even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your • Under no circumstances should oil change intervals exceed 6,000 miles (10,000 km) or six months, which- ever comes first.
vehicle off-road for an extended period of time.
Your authorized dealer will reset the oil change indicator message after completing the scheduled oil change. If a scheduled oil change is performed by someone other than your authorized dealer, the message can be reset by referring to the steps described under “Oil Change Required” under “Electronic Vehicle Information Center
MAINTENANCE SCHEDULES 475
(EVIC)” in Section 4 or under “Odometer/Trip Odom- eter” under “Instrument Cluster Descriptions” in Sec- tion 4. At Each Stop for Fuel • Check the engine oil level. Refer to “Engine Oil” under • Check the windshield washer solvent and add if
“Maintenance Procedures” in Section 7.
required.
Once a Month • Check tire pressure and look for unusual wear or • Inspect the battery, and clean and tighten the terminals
damage.
as required.
476 MAINTENANCE SCHEDULES
• Check the fluid levels of coolant reservoir, brake master cylinder, power steering, and transmission, and add as needed. • Check all lights and other electrical items for correct
operation.
At Each Oil Change • Change the engine oil filter. • Inspect the brake hoses and lines.
CAUTION!
Failure to perform the required maintenance items may result in damage to the vehicle.
Required Maintenance Intervals Refer to the Maintenance Schedules on the following pages for the required maintenance intervals.
6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires.
MAINTENANCE SCHEDULES 477
12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
❏ Replace the air conditioning filter (if equipped) Inspect the brake linings; replace if necessary. Inspect the CV joints. Perform the first inspection at 12,000 miles (20 000 km) or 12 months. Inspect exhaust system. Perform the first inspection at 12,000 miles (20 000 km) or 12 months.
Odometer Reading
Repair Order #
Date
Dealer Code
Odometer Reading
Repair Order #
Date
Dealer Code
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
❏ ❏ ❏ ❏ M
478 MAINTENANCE SCHEDULES
18,000 Miles (30,000 km) or 18 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires.
Inspect the rear axle fluid. Inspect the front axle fluid — All Wheel Drive (AWD).
24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
❏ Replace the air conditioning filter (if equipped) Inspect the brake linings; replace if necessary. Inspect the CV joints. Inspect exhaust system. Inspect the front suspension, tie rod ends and boot seals; replace if necessary.
Odometer Reading
Repair Order #
Date
Dealer Code
Odometer Reading
Repair Order #
Date
Dealer Code
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
❏ ❏ ❏ ❏ ❏ ❏ MAINTENANCE SCHEDULES 479
36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
❏ Replace the air conditioning filter (if equipped)
Inspect the rear axle fluid. Inspect the front axle fluid — All Wheel Drive (AWD). Inspect the brake linings; replace if necessary.
30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires. ❏ Replace the engine air cleaner filter. Replace the spark plugs (2.7L and 5.7L Engines). Inspect the transfer case fluid — All Wheel Drive (AWD).
❏ Adjust parking brake on vehicles
equipped with four-wheel disc brakes.
Odometer Reading
Repair Order #
Date
Dealer Code
Odometer Reading
Repair Order #
Date
Dealer Code
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
❏ ❏ ❏ ❏ ❏ M
480 MAINTENANCE SCHEDULES
42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires.
48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
❏ Replace the air conditioning filter (if equipped) Inspect the brake linings; replace if necessary. Inspect the CV joints. Inspect exhaust system. Inspect the front suspension, tie rod ends and boot seals; replace if necessary.
❏ Change the rear axle fluid and on models equipped with All Wheel Drive (AWD) change the front axle fluid if using your vehicle for any of the following: police, taxi, fleet, off-road, or frequent trailer towing.
Odometer Reading
Repair Order #
Date
Dealer Code
Odometer Reading
Repair Order #
Date
Dealer Code
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
❏ ❏ ❏ ❏ ❏ 54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires.
Inspect the rear axle fluid. Inspect the front axle fluid — All Wheel Drive (AWD).
MAINTENANCE SCHEDULES 481
60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter.
Replace the spark plugs (2.7L and 5.7L Engines).
❏ Replace the air conditioning filter (if equipped) Inspect the brake linings; replace if necessary.
❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ Change the automatic transmission fluid and filter if using your vehicle for any of the
following: police, taxi, fleet, or frequent trailer towing.
❏ Change the transfer case fluid if using your vehicle for any of the following: police, taxi,
fleet, or frequent trailer towing — All Wheel Drive (AWD). Flush and replace the engine coolant at 60 months if not done at 102,000 miles (170 000 km).
Odometer Reading
Repair Order #
Date
Dealer Code
Odometer Reading
Repair Order #
Date
Dealer Code
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
❏ ❏ ❏ ❏ M
482 MAINTENANCE SCHEDULES
66,000 Miles (110,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires.
72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
❏ Replace the air conditioning filter (if equipped)
Inspect the rear axle fluid. Inspect the front axle fluid — All Wheel Drive (AWD). Inspect the brake linings; replace if necessary. Inspect the CV joints. Inspect exhaust system. Inspect the front suspension, tie rod ends and boot seals; replace if necessary.
Odometer Reading
Repair Order #
Date
Dealer Code
Odometer Reading
Repair Order #
Date
Dealer Code
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
❏ ❏ ❏ ❏ ❏ ❏ 78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires.
filter.
❏ Rotate tires.
If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
❏ Replace the air conditioning filter (if
equipped) Inspect the brake linings; replace if necessary.
Odometer Reading
Date
Odometer Reading
Repair Order #
Dealer Code
Repair Order #
Date
Dealer Code
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
MAINTENANCE SCHEDULES 483
❏ ❏ M
484 MAINTENANCE SCHEDULES
90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter.
Replace the spark plugs (2.7L and 5.7L Engines). Inspect and replace PCV valve if necessary. † Inspect the rear axle fluid. Inspect the front axle fluid — All Wheel Drive (AWD). Inspect the transfer case fluid — All Wheel Drive (AWD).
❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes.
Odometer Reading
Repair Order #
