2015 Chevrolet VOLT Owners Manual

R1

R2
R3
R4

Retained Accessory Power Relay for Power Outlets Empty Empty Empty

Diodes DIODE

Empty

Usage

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (37,1)

Vehicle Care

10-37

Instrument Panel Fuse Block (Right Side) The right instrument panel fuse block is on the right side end of the instrument panel. To access the fuses, open the fuse panel door by pulling out. To reinstall the door, insert the bottom tab first, then push the door back into its original location.

Instrument Panel Fuse Block

A fuse puller is in the engine compartment fuse block. The vehicle may not be equipped with all of the fuses, relays, and features shown.

Fuses

Usage

F1

F2
F3

Steering Wheel Switch Backlighting Empty Empty

Fuses

F4

F5

Usage Body Control Module 3/Right Headlamp Body Control Module 2/Body Control Module Electronics/Hatch Lamp/Right Daytime Running Lamp/ Shifter Lock/Switch Backlighting

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (38,1)

10-38

Vehicle Care

Fuses

Usage

F6
F7

F8

F9

F10

Empty Body Control Module 6/Map Lights/Courtesy Lights/Back– up Lamp Body Control Module 7/Left Front Turn Signal/Right Rear Stop and Turn Signal Lamp/Child Security Lock Relay Control Body Control Module 8/Locks Data Link Connector, Right (Secondary)

Fuses

F11

F12
F13
F14
F15
F16
F17
F18

Usage

Relays

Usage

R1
R2
R3
R4

Empty Empty Empty Child Lockout Relay

Diodes DIODE

Empty

Usage

Universal Garage Door Opener (If Equipped) Blower Motor Empty Empty Empty Empty Empty Empty

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (39,1)

Rear Compartment Fuse Block

The rear compartment fuse block is on the left side of the rear compartment behind a removable cover. Open the latch to remove the cover and access the fuse block.

A fuse puller is in the engine compartment fuse block.

The vehicle may not have all of the fuses, relays, and features shown.

Vehicle Care

10-39

Fuses

Usage

F1
F2

F3

F4

F5

F6

F7

F8

F9

Empty Fuel System Control Module Passive Start/ Passive Entry Module Heated Seats (If Equipped) Driver Door Switches (Outside Rearview Mirror/ Charge Port Door Release/Refuel Request/Driver Window Switch) Fuel (Diurnal Valve and Evap. Leak Check Module) Accessory Power Module Cooling Fan Amplifier (If Equipped) Empty

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (40,1)

10-40

Vehicle Care

Fuses

F10

F11
F12

F13

F14
F15
F16
F17
F18

Usage

Relays

Usage

R1
R2
R3
R4
R5
R6

R7/R8

Diodes DIODE

Rear Defog Hatch Release Empty Empty Empty Empty Horn

Usage

Empty

Regulated Voltage Control/Front and Rear Parking Assist (If Equipped) Horn Rear Power Windows Electric Parking Brake Rear Defog Empty Hatch Release Empty Empty

Wheels and Tires

Tires Every new GM vehicle has high-quality tires made by a leading tire manufacturer. See the warranty manual for information regarding the tire warranty and where to get service. For additional information refer to the tire manufacturer.

{ Warning

. Poorly maintained and

improperly used tires are dangerous.

. Overloading the tires can

cause overheating as a result of too much flexing.

(Continued)

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (41,1)

Vehicle Care

10-41

Warning (Continued)

Warning (Continued)

Warning (Continued)

There could be a blowout and a serious crash. See Vehicle Load Limits on page 9-11.

. Underinflated tires pose

the same danger as overloaded tires. The resulting crash could cause serious injury. Check all tires frequently to maintain the recommended pressure. Tire pressure should be checked when the tires are cold.

. Overinflated tires are more likely to be cut, punctured, or broken by a sudden impact — such as when hitting a pothole. Keep tires at the recommended pressure.

(Continued)

. Worn or old tires can

cause a crash. If the tread is badly worn, replace them.

. Replace any tires that

have been damaged by impacts with potholes, curbs, etc.

. Improperly repaired tires

can cause a crash. Only the dealer or an authorized tire service center should repair, replace, dismount, and mount the tires.

(Continued)

. Do not spin the tires in

excess of 56 km/h (35 mph) on slippery surfaces such as snow, mud, ice, etc. Excessive spinning may cause the tires to explode.

All-Season Tires This vehicle may come with all-season tires. These tires are designed to provide good overall performance on most road surfaces and weather conditions. Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. Original equipment all-season tires can be identified by the last two characters of this TPC code, which will be “MS.”

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (42,1)

10-42

Vehicle Care

Consider installing winter tires on the vehicle if frequent driving on snow or ice-covered roads is expected. All-season tires provide adequate performance for most winter driving conditions, but they may not offer the same level of traction or performance as winter tires on snow or ice-covered roads. See Winter Tires on page 10-42.

Winter Tires This vehicle was not originally equipped with winter tires. Winter tires are designed for increased traction on snow and ice-covered roads. Consider installing winter tires on the vehicle if frequent driving on ice or snow covered roads is expected. See your dealer for details regarding winter tire availability and proper tire selection. Also, see Buying New Tires on page 10-55.

With winter tires, there may be decreased dry road traction, increased road noise, and shorter tread life. After changing to winter tires, be alert for changes in vehicle handling and braking. If using winter tires: . Use tires of the same brand and

tread type on all four wheel positions.

. Use only radial ply tires of the

same size, load range, and speed rating as the original equipment tires.

Winter tires with the same speed rating as the original equipment tires may not be available for H, V, W, Y, and ZR speed rated tires. If winter tires with a lower speed rating are chosen, never exceed the tire's maximum speed capability.

Summer Tires This vehicle may come with high performance summer tires. These tires have a special tread and compound that are optimized for maximum dry and wet road performance. This special tread and compound will have decreased performance in cold climates, and on ice and snow. We recommend installing winter tires on the vehicle if frequent driving at temperatures below approximately 5°C (40°F) or on ice or snow covered roads is expected. See Winter Tires on page 10-42.

Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples show a typical passenger tire sidewall.

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (43,1)

criteria have a TPC specification code molded onto the sidewall. GM's TPC specifications meet or exceed all federal safety guidelines. (3) DOT (Department of Transportation): The Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S. Department of Transportation Motor Vehicle Safety Standards. DOT Tire Date of Manufacture: The last four digits of the TIN indicate the tire manufactured date. The first two digits represent the week (01-52) and the last two digits, the year. For example, the third week of the year 2010 would have a four-digit DOT date of 0310.

Vehicle Care

10-43

(4) Tire Identification Number (TIN): The letters and numbers following the DOT code are the Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (5) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread. (6) Uniform Tire Quality Grading (UTQG): Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction, and temperature resistance. For more information see Uniform Tire Quality Grading on page 10-57.

Passenger (P-Metric) Tire Example (1) Tire Size: The tire size is a combination of letters and numbers used to define a particular tire's width, height, aspect ratio, construction type, and service description. See the “Tire Size” illustration later in this section for more detail. (2) TPC Spec (Tire Performance Criteria Specification): Original equipment tires designed to GM's specific tire performance

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (44,1)

10-44

Vehicle Care

(7) Maximum Cold Inflation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load.

Tire Designations

Tire Size The following is an example of a typical passenger vehicle tire size.

(1) Passenger (P-Metric) Tire: The United States version of a metric tire sizing system. The letter P as the first character in the tire size means a passenger

vehicle tire engineered to standards set by the U.S. Tire and Rim Association. (2) Tire Width: The three-digit number indicates the tire section width in millimeters from sidewall to sidewall. (3) Aspect Ratio: A two-digit number that indicates the tire height-to-width measurements. For example, if the tire size aspect ratio is 60, as shown in item 3 of the illustration, it would mean that the tire's sidewall is 60 percent as high as it is wide. (4) Construction Code: A letter code is used to indicate the type of ply construction in the tire. The letter R means radial ply construction; the letter D means diagonal or bias ply construction; and the letter B means belted-bias ply construction.

(5) Rim Diameter: Diameter of the wheel in inches. (6) Service Description: These characters represent the load index and speed rating of the tire. The load index represents the load carrying capacity a tire is certified to carry. The speed rating is the maximum speed a tire is certified to carry a load.

Tire Terminology and Definitions Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in kPa (kilopascal) or psi (pounds per square inch). Accessory Weight: The combined weight of optional accessories. Some examples of optional accessories are, electric

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (45,1)

drive unit, power windows, power seats, and air conditioning. Aspect Ratio: The relationship of a tire's height to its width. Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread. Cold Tire Pressure: The amount of air pressure in a tire, measured in kPa (kilopascal) or psi (pounds per square inch)

before a tire has built up heat from driving. See Tire Pressure on page 10-47. Curb Weight: The weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil, and coolant, but without passengers and cargo. DOT Markings: A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation (DOT) Motor Vehicle Safety Standards. The DOT code includes the Tire Identification Number (TIN), an alphanumeric designator which can also identify the tire manufacturer, production plant, brand, and date of production. GVWR: Gross Vehicle Weight Rating. See Vehicle Load Limits on page 9-11.

Vehicle Care

10-45

GAWR FRT: Gross Axle Weight Rating for the front axle. See Vehicle Load Limits on page 9-11. GAWR RR: Gross Axle Weight Rating for the rear axle. See Vehicle Load Limits on page 9-11. Intended Outboard Sidewall: The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure. Light Truck (LT-Metric) Tire: A tire used on light duty trucks and some multipurpose passenger vehicles. Load Index: An assigned number ranging from 1 to 279
that corresponds to the load carrying capacity of a tire.

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (46,1)

10-46

Vehicle Care

Maximum Inflation Pressure: The maximum air pressure to which a cold tire can be inflated. The maximum air pressure is molded onto the sidewall. Maximum Load Rating: The load rating for a tire at the maximum permissible inflation pressure for that tire. Maximum Loaded Vehicle Weight: The sum of curb weight, accessory weight, vehicle capacity weight, and production options weight. Normal Occupant Weight: The number of occupants a vehicle is designed to seat multiplied by 68 kg (150 lbs). See Vehicle Load Limits on page 9-11. Occupant Distribution: Designated seating positions.

Outward Facing Sidewall: The side of an asymmetrical tire that has a particular side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering, or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire. Passenger (P-Metric) Tire: A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inflation Pressure: Vehicle manufacturer's recommended tire inflation pressure as shown on the tire placard. See Tire Pressure on page 10-47 and Vehicle Load Limits on page 9-11.

Radial Ply Tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim: A metal support for a tire and upon which the tire beads are seated. Sidewall: The portion of a tire between the tread and the bead. Speed Rating: An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. Traction: The friction between the tire and the road surface. The amount of grip provided. Tread: The portion of a tire that comes into contact with the road.

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (47,1)

Treadwear Indicators: Narrow bands, sometimes called wear bars, that show across the tread of a tire when only 1.6 mm (1/16 in) of tread remains. See When It Is Time for New Tires on page 10-54. UTQGS (Uniform Tire Quality Grading Standards): A tire information system that provides consumers with ratings for a tire's traction, temperature, and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire. See Uniform Tire Quality Grading on page 10-57. Vehicle Capacity Weight: The number of designated seating positions multiplied by

68 kg (150 lbs) plus the rated cargo load. See Vehicle Load Limits on page 9-11. Vehicle Maximum Load on the Tire: Load on an individual tire due to curb weight, accessory weight, occupant weight, and cargo weight. Vehicle Placard: A label permanently attached to a vehicle showing the vehicle's capacity weight and the original equipment tire size and recommended inflation pressure. See “Tire and Loading Information Label” under Vehicle Load Limits on page 9-11.

Tire Pressure Tires need the correct amount of air pressure to operate effectively.

Vehicle Care

10-47

{ Caution

Neither tire underinflation nor overinflation is good. Underinflated tires, or tires that do not have enough air, can result in:

. Tire overloading and

overheating which could lead to a blowout.

. Premature or irregular wear. . Poor handling. . Reduced fuel economy.

Overinflated tires, or tires that have too much air, can result in:

. Unusual wear. . Poor handling. . Rough ride. . Needless damage from

road hazards.

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (48,1)

10-48

Vehicle Care

The Tire and Loading Information label on the vehicle indicates the original equipment tires and the correct cold tire inflation pressures. The recommended pressure is the minimum air pressure needed to support the vehicle's maximum load carrying capacity. For additional information regarding how much weight the vehicle can carry, and an example of the Tire and Loading Information label, see Vehicle Load Limits on page 9-11. How the vehicle is loaded affects vehicle handling and ride comfort. Never load the vehicle with more weight than it was designed to carry.

When to Check Check the tires once a month or more.

How to Check Use a good quality pocket-type gauge to check the tire pressure. Proper tire inflation cannot be determined by looking at the tire. Check the tire inflation pressure when the tires are cold, meaning the vehicle has not been driven for at least three hours or no more than 1.6 km (1 mi). Remove the valve cap from the tire valve stem. Press the tire gauge firmly onto the valve to get the pressure measurement. If the cold tire inflation pressure matches the recommended pressure on the Tire and Loading Information label, no further adjustment is necessary. If the inflation pressure is low, add air until the recommended pressure is reached. If the inflation pressure in high, press on the metal stem in the center

of the tire valve to release air. Re-check the tire pressure with the tire gauge. Return the valve caps on the valve stems to keep out dirt and moisture and prevent leaks.

Tire Pressure Monitor System The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your tires and transmit tire pressure readings to a receiver located in the vehicle. Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (49,1)

tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle's handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver's responsibility to maintain correct tire pressure, even if under-inflation has

not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more

Vehicle Care

10-49

tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. See Tire Pressure Monitor Operation on page 10-49. See Radio Frequency Statement on page 13-12.

Tire Pressure Monitor Operation This vehicle may have a Tire Pressure Monitor System (TPMS). The TPMS is designed to warn the driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly. The TPMS sensors monitor the air pressure in the tires and transmit the tire pressure readings to a receiver located in the vehicle.

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (50,1)

10-50

Vehicle Care

When a low tire pressure condition is detected, the TPMS illuminates the low tire pressure warning light located on the instrument cluster. If the warning light comes on, stop as soon as possible and inflate the tires to the recommended pressure shown on the Tire Loading and Information label. See Vehicle Load Limits on page 9-11. A message to check the pressure in a specific tire displays in the Driver Information Center (DIC). The low tire pressure warning light and the DIC warning message come on at each drive cycle until the tires are inflated to the correct inflation pressure. Using the DIC, tire pressure levels can be viewed. For additional information and details

about the DIC operation and displays see Driver Information Center (DIC) on page 5-40. The low tire pressure warning light may come on in cool weather when the vehicle is first started, and then turn off as the vehicle is driven. This could be an early indicator that the air pressure is getting low and needs to be inflated to the proper pressure. A Tire and Loading Information label shows the size of the original equipment tires and the correct inflation pressure for the tires when they are cold. See Vehicle Load Limits on page 9-11, for an example of the Tire and Loading Information label and its location. Also see Tire Pressure on page 10-47. The TPMS can warn about a low tire pressure condition but it does not replace normal tire maintenance. See Tire Inspection on page 10-53, Tire Rotation on page 10-53, and Tires on page 10-40.

{ Caution

Tire sealant materials are not all the same. A non-approved tire sealant could damage the TPMS sensors. TPMS sensor damage caused by using an incorrect tire sealant is not covered by the vehicle warranty. Always use only the GM approved tire sealant available through your dealer or included in the vehicle.

Factory-installed Tire Inflator Kits use a GM approved liquid tire sealant. Using non-approved tire sealants could damage the TPMS sensors. See Tire Sealant and Compressor Kit on page 10-61 for information regarding the inflator kit materials and instructions.

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (51,1)

TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire pressure warning light flashes for about one minute and then stays on for the remainder of the vehicle on/off cycle. A DIC warning message also displays. The malfunction light and DIC warning message come on at each vehicle on/off cycle until the problem is corrected. Some of the conditions that can cause these to come on are: . One of the road tires has been

replaced with the spare tire, if the vehicle has one. The spare tire does not have a TPMS sensor. The malfunction light and DIC message should go off after the road tire is replaced and the sensor matching process is performed

successfully. See "TPMS Sensor Matching Process" later in this section. The TPMS sensor matching process was started but not completed or not completed successfully after rotating the tires. The DIC message and malfunction light should go off once the TPMS sensor matching process is performed successfully. See “TPMS Sensor Matching Process” later in this section.

. One or more TPMS sensors are

missing or damaged. The DIC message and the malfunction light should go off when the TPMS sensors are installed and the sensor matching process is performed successfully. See your dealer for service.

. Replacement tires or wheels do not match the original equipment tires or wheels. Tires and wheels other than those recommended

Vehicle Care

10-51

could prevent the TPMS from functioning properly. See Buying New Tires on page 10-55.

. Operating electronic devices or being near facilities using radio wave frequencies similar to the TPMS could cause the TPMS sensors to malfunction.

If the TPMS is not functioning properly , it cannot detect or signal a low tire condition. See your dealer for service if the TPMS malfunction light and DIC message come on and stay on. TPMS Sensor Matching Process Each TPMS sensor has a unique identification code. The identification code needs to be matched to a new tire/wheel position after rotating the vehicle’s tires or replacing one or more of the TPMS sensors. Also, the TPMS sensor matching process should be performed after replacing a spare tire with a road tire containing the TPMS sensor. The malfunction light and the DIC

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (52,1)

10-52

Vehicle Care

message should go off at the next drive cycle. The sensors are matched to the tire/wheel positions, using a TPMS relearn tool, in the following order: driver side front tire, passenger side front tire, passenger side rear tire, and driver side rear. See your dealer for service or to purchase a relearn tool. A TPMS relearn tool can also be purchased. See Tire Pressure Monitor Sensor Activation Tool at www.gmtoolsandequipment.com or call 1-800-GM TOOLS (1-800-468-6657). There are two minutes to match the first tire/wheel position, and five minutes overall to match all four tire/wheel positions. If it takes longer, the matching process stops and must be restarted. Follow the TPMS sensor matching process: 1. Set the parking brake. 2. Put the vehicle in ON/RUN and

place the vehicle in P (Park).

3.

If the DIC display is minimized, press the SELECT knob to maximize it.

4. Use the SELECT knob to scroll

to the Tire Pressure display screen.

5. Press and hold the SELECT

knob for five seconds to begin the sensor matching process. A message displays confirming to begin the process.

6. Use the SELECT knob to select

YES with the highlighted selection, and press the SELECT knob again to confirm the selection. The horn sounds twice to signal the receiver is in relearn mode and the TIRE LEARNING ACTIVE message displays on the DIC screen.

7. Start with the driver side

front tire.

8. Place the relearn tool against

the tire sidewall, near the valve stem. Then press the button to

activate the TPMS sensor. A horn chirp confirms that the sensor identification code has been matched to this tire and wheel position.

9. Proceed to the passenger side

front tire, and repeat the procedure in Step 8.

10. Proceed to the passenger side

rear tire, and repeat the procedure in Step 8.

11. Proceed to the driver side rear tire, and repeat the procedure in Step 8. The horn sounds two times to indicate the sensor identification code has been matched to the driver side rear tire, and the TPMS sensor matching process is no longer active. The TIRE LEARNING ACTIVE message on the DIC display screen goes off.

12. Turn the vehicle off.

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (53,1)

Vehicle Care

10-53

13. Set all four tires to the

recommended air pressure level as indicated on the Tire and Loading Information label.

Tire Inspection We recommend that the tires, including the spare tire, if the vehicle has one, be inspected for signs of wear or damage at least once a month. Replace the tire if: . The indicators at three or

more places around the tire can be seen.

. There is cord or fabric

showing through the tire's rubber.

. The tread or sidewall is

cracked, cut, or snagged deep enough to show cord or fabric.

. The tire has a bump, bulge,

or split.

. The tire has a puncture, cut, or other damage that cannot be repaired well because of the size or location of the damage.

Tire Rotation Tires should be rotated every 12 000 km (7,500 mi). The first rotation is the most important. See Maintenance Schedule on page 11-3. Tires are rotated to achieve a more uniform wear for all tires. Anytime unusual wear is noticed, rotate the tires as soon as possible, check for proper tire inflation pressure, and check for damaged tires or wheels. If the unusual wear continues after the rotation, check the wheel alignment. See When It Is Time for New Tires on page 10-54
and Wheel Replacement on page 10-59.

Use this rotation pattern when rotating the tires. Adjust the front and rear tires to the recommended inflation pressure on the Tire and Loading Information label after the tires have been rotated. See Tire Pressure on page 10-47
and Vehicle Load Limits on page 9-11. Reset the Tire Pressure Monitor System. See Tire Pressure Monitor Operation on page 10-49.

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (54,1)

10-54

Vehicle Care

Check that all wheel nuts are properly tightened. See “Wheel Nut Torque” under Capacities and Specifications on page 12-2.

tire rotation to prevent corrosion or rust build-up. Do not get grease on the flat wheel mounting surface or on the wheel nuts or bolts.

When It Is Time for New Tires Factors such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions affect the wear rate of the tires.

{ Warning

Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after a time. The wheel could come off and cause a crash. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, a cloth or a paper towel can be used, however, use a scraper or wire brush to remove all rust or dirt.

Lightly coat the center of the wheel hub with wheel bearing grease after a wheel change or

Treadwear indicators are one way to tell when it is time for new tires. Treadwear indicators appear when the tires have only 1.6 mm (1/16 in) or less of tread remaining. See Tire Inspection on page 10-53 and Tire Rotation on page 10-53. The rubber in tires ages over time. This also applies to the spare tire, if the vehicle has one, even if it is never used. Multiple factors including temperatures, loading conditions, and inflation pressure maintenance affect how fast aging takes place. GM recommends that tires, including the spare if equipped, be replaced after six years, regardless of tread wear. The tire manufacture date is the last four digits of the DOT Tire Identification Number (TIN) which is molded into one side of the tire sidewall. The first two digits represent the week (01–52) and the last two digits, the year. For example, the third week of the year 2010 would have a four-digit DOT date of 0310.

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (55,1)

Vehicle Storage Tires age when stored normally mounted on a parked vehicle. Park a vehicle that will be stored for at least a month in a cool, dry, clean area away from direct sunlight to slow aging. This area should be free of grease, gasoline, or other substances that can deteriorate rubber. Parking for an extended period can cause flat spots on the tires that may result in vibrations while driving. When storing a vehicle for at least a month, remove the tires or raise the vehicle to reduce the weight from the tires.

Buying New Tires GM has developed and matched specific tires for the vehicle. The original equipment tires installed were designed to meet General Motors Tire Performance Criteria Specification (TPC Spec) system rating.

When replacement tires are needed, GM strongly recommends buying tires with the same TPC Spec rating. GM's exclusive TPC Spec system considers over a dozen critical specifications that impact the overall performance of the vehicle, including brake system performance, ride and handling, traction control, and tire pressure monitoring performance. GM's TPC Spec number is molded onto the tire's sidewall near the tire size. If the tires have an all-season tread design, the TPC spec number will be followed by MS, for mud and snow. See Tire Sidewall Labeling on page 10-42. GM recommends replacing worn tires in complete sets of four. Uniform tread depth on all tires will help to maintain the performance of the vehicle.

Vehicle Care

10-55

Braking and handling performance may be adversely affected if all the tires are not replaced at the same time. If proper rotation and maintenance have been done, all four tires should wear out at about the same time. See Tire Rotation on page 10-53. However, if it is necessary to replace only one axle set of worn tires, place the new tires on the rear axle. Winter tires with the same speed rating as the original equipment tires may not be available for H, V, W, Y, and ZR speed rated tires. Never exceed the winter tires’ maximum speed capability when using winter tires with a lower speed rating.

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (56,1)

10-56

Vehicle Care

{ Warning

{ Warning

Tires could explode during improper service. Attempting to mount or dismount a tire could cause injury or death. Only your dealer or authorized tire service center should mount or dismount the tires.

{ Warning

Mixing tires of different sizes, brands, or types may cause loss of control of the vehicle, resulting in a crash or other vehicle damage. Use the correct size, brand, and type of tire on all wheels.

Using bias-ply tires on the vehicle may cause the wheel rim flanges to develop cracks after many miles of driving. A tire and/or wheel could fail suddenly and cause a crash. Use only radial-ply tires with the wheels on the vehicle.

If the vehicle tires must be replaced with a tire that does not have a TPC Spec number, make sure they are the same size, load range, speed rating, and construction (radial) as the original tires. Vehicles that have a tire pressure monitoring system could give an inaccurate low-pressure warning if non-TPC Spec rated tires are installed. See Tire Pressure Monitor System on page 10-48.

The Tire and Loading Information Label indicates the original equipment tires on the vehicle. See Vehicle Load Limits on page 9-11, for the label location and more information about the Tire and Loading Information label.

Different Size Tires and Wheels If wheels or tires are installed that are a different size than the original equipment wheels and tires, vehicle performance, including its braking, ride and handling characteristics, stability, and resistance to rollover may be affected. If the vehicle has electronic systems such as antilock brakes, rollover airbags, traction control, electronic stability control, or All-Wheel Drive, the performance of these systems can also be affected.

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (57,1)

{ Warning

If different sized wheels are used, there may not be an acceptable level of performance and safety if tires not recommended for those wheels are selected. This increases the chance of a crash and serious injury. Only use GM specific wheel and tire systems developed for the vehicle, and have them properly installed by a GM certified technician.

See Buying New Tires on page 10-55 and Accessories and Modifications on page 10-2.

Uniform Tire Quality Grading The following information relates to the system developed by the United States National Highway Traffic Safety Administration

(NHTSA), which grades tires by treadwear, traction, and temperature performance. This applies only to vehicles sold in the United States. The grades are molded on the sidewalls of most passenger car tires. The Uniform Tire Quality Grading (UTQG) system does not apply to deep tread, winter tires, compact spare tires, tires with nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-production tires. While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades, they must also conform to federal safety requirements and additional General Motors Tire Performance Criteria (TPC) standards.

Vehicle Care

10-57

Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example:

Treadwear 200 Traction AA Temperature A All Passenger Car Tires Must Conform to Federal Safety Requirements In Addition To These Grades.

Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1½) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (58,1)

10-58

Vehicle Care

their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.

Traction The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warning: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.

Temperature The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. Warning: The temperature grade for this tire is established for a tire that is properly inflated and not

overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.

Wheel Alignment and Tire Balance The tires and wheels were aligned and balanced at the factory to provide the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing are not necessary on a regular basis. Consider an alignment check if there is unusual tire wear or the vehicle is significantly pulling to one side or the other. Some slight pull to the left or right, depending on the crown of the road and/or other road surface variations such as troughs or ruts, is normal. If the vehicle is vibrating when driving on a smooth road, the tires and wheels may need to be rebalanced. See your dealer for proper diagnosis.

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (59,1)

Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts, and wheel nuts should be replaced. If the wheel leaks air, replace it. Some aluminum wheels can be repaired. See your dealer if any of these conditions exist. Your dealer will know the kind of wheel that is needed. Each new wheel should have the same load-carrying capacity, diameter, width, and offset, and should be mounted the same way as the one it replaces. Replace wheels, wheel bolts, wheel nuts, or Tire Pressure Monitor System (TPMS) sensors with new GM original equipment parts.

Vehicle Care

10-59

{ Warning

{ Warning

Using the wrong replacement wheels, wheel bolts, or wheel nuts can be dangerous. It could affect the braking and handling of the vehicle. Tires can lose air, and cause loss of control, causing a crash. Always use the correct wheel, wheel bolts, and wheel nuts for replacement.

{ Caution

The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, bumper height, vehicle ground clearance, and tire clearance to the body and chassis.

Never use oil or grease on studs or the threads of the wheel nuts. The wheel nuts might come loose and the wheel could fall off, causing a crash.

{ Warning

Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose and even come off. This could lead to a crash. Be sure to use the correct wheel nuts. If you have to replace them, be sure to get new GM original equipment wheel nuts.

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (60,1)

10-60

Vehicle Care

{ Caution

Improperly tightened wheel nuts can lead to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque specification.

Used Replacement Wheels

{ Warning

Replacing a wheel with a used one is dangerous. How it has been used or how far it has been driven may be unknown. It could fail suddenly and cause a crash. When replacing wheels, use a new GM original equipment wheel.

Tire Chains

{ Warning

Do not use tire chains. There is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle parts. The area damaged by the tire chains could cause loss of control and a crash. Use another type of traction device only if its manufacturer recommends it for the vehicle's tire size combination and road conditions. Follow that manufacturer's instructions. To avoid vehicle damage, drive slow and readjust or remove the traction device if it contacts the vehicle. Do not spin the wheels. If traction devices are used, install them on the front tires.

If a Tire Goes Flat This vehicle has a tire sealant and compressor kit. See Tire Sealant and Compressor Kit on page 10-61. There is no spare tire, no tire changing equipment, and no place to store a tire. To properly lift this vehicle, see Lifting the Vehicle on page 10-3. It is unusual for a tire to blowout while driving, especially if the tires are maintained properly. See Tires on page 10-40. If air goes out of a tire, it is much more likely to leak out slowly. But if there ever is a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire will create a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly. Steer to maintain lane position, and then gently brake to a stop, well off the road, if possible.

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (61,1)

A rear blowout, particularly on a curve, acts much like a skid and may require the same correction as used in a skid. Stop pressing the accelerator pedal and steer to straighten the vehicle. It may be very bumpy and noisy. Gently brake to a stop, well off the road, if possible.

{ Warning

Driving on a flat tire will cause permanent damage to the tire. Re-inflating a tire after it has been driven on while severely underinflated or flat may cause a blowout and a serious crash. Never attempt to re-inflate a tire that has been driven on while severely underinflated or flat. Have your dealer or an authorized tire service center repair or replace the flat tire as soon as possible.

If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place and stopping, well off the road, if possible. 1. Turn on the hazard warning

flashers. See Hazard Warning Flashers on page 6-3.

2. Set the parking brake firmly. 3. Put the shift lever in P (Park).

See Shifting Into Park on page 9-19.

4. Turn off the engine. 5. Inspect the flat tire. If the tire has been separated from the wheel, has damaged sidewalls, or has a puncture larger than 6 mm (0.25 in), the tire is too severely damaged for the tire sealant and compressor kit to be effective. See Roadside Assistance Program on page 13-5. If the tire has a puncture less than 6 mm (0.25 in) in the tread area of the tire, see Tire Sealant and Compressor Kit on page 10-61.

Vehicle Care

10-61

Tire Sealant and Compressor Kit

{ Warning

Running the engine in Extended Range Mode in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains carbon monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. Never run the engine in Extended Range Mode in an enclosed area that has no fresh air ventilation. For more information, see Engine Exhaust on page 9-26.

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (62,1)

The kit includes:

10-62

Vehicle Care

{ Warning

Overinflating a tire could cause the tire to rupture and you or others could be injured. Be sure to read and follow the tire sealant and compressor kit instructions and inflate the tire to its recommended pressure. Do not exceed the recommended pressure.

{ Warning

Storing the tire sealant and compressor kit or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store the tire sealant and compressor kit in its original location.

If this vehicle has a tire sealant and compressor kit, there may not be a spare tire or tire changing equipment, and on some vehicles there may not be a place to store a tire. The tire sealant and compressor can be used to temporarily seal punctures up to 6 mm (0.25 in) in the tread area of the tire. It can also be used to inflate an underinflated tire. If the tire has been separated from the wheel, has damaged sidewalls, or has a large puncture, the tire is too severely damaged for the tire sealant and compressor kit to be effective. See Roadside Assistance Program on page 13-5. Read and follow all of the tire sealant and compressor kit instructions.

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (63,1)

Vehicle Care

10-63

There is only enough sealant to seal one tire. After usage, the sealant canister and sealant/air hose assembly must be replaced. See “Removal and Installation of the Sealant Canister” following. Using the Tire Sealant and Compressor Kit to Temporarily Seal and Inflate a Punctured Tire Follow the directions closely for correct sealant usage.

1. Selector Switch (Sealant/Air

or Air Only)

2. On/Off Button 3. Pressure Gauge 4. Pressure Deflation Button

(If equipped)

5. Tire Sealant Canister 6. Sealant/Air Hose (Clear) 7. Air Only Hose (Black) 8. Power Plug 9. Canister Release Button (Under Sealant/Air Hose)

Tire Sealant Read and follow the safe handling instructions on the label adhered to the sealant canister. Check the tire sealant expiration date on the sealant canister. The sealant canister should be replaced before its expiration date. Replacement sealant canisters are available at your local dealer. See “Removal and Installation of the Sealant Canister” following.

When using the tire sealant and compressor kit during cold temperatures, warm the kit in a

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (64,1)

10-64

Vehicle Care

heated environment for five minutes. This will help to inflate the tire faster. If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 6-3. See If a Tire Goes Flat on page 10-60 for other important safety warnings. Do not remove any objects that have penetrated the tire. 1. Remove the tire sealant and

compressor kit from its storage location. See Storing the Tire Sealant and Compressor Kit on page 10-69.

2. Unwrap the sealant/air hose (6)

and the power plug (8).

3. Place the kit on the ground.

4. Remove the valve stem cap from

9. Press the on/off button (2) to

the flat tire by turning it counterclockwise.

5. Attach the sealant/air hose (6) onto the tire valve stem. Turn it clockwise until it is tight.

6. Plug the power plug (8) into the

accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Power Outlets on page 5-7. If the vehicle has an accessory power outlet, do not use the cigarette lighter. If the vehicle only has a cigarette lighter, use the cigarette lighter. Do not pinch the power plug cord in the door or window.

7. Start the vehicle. The vehicle

must be running while using the air compressor.

turn the tire sealant and compressor kit on. The compressor will inject sealant and air into the tire. The pressure gauge (3) will initially show a high pressure while the compressor pushes the sealant into the tire. Once the sealant is completely dispersed into the tire, the pressure will quickly drop and start to rise again as the tire inflates with air only.

Inflate the tire to the recommended inflation pressure using the pressure gauge (3). The recommended inflation pressure can be found on the Tire and Loading Information label. See Tire Pressure on page 10-47.

10.

Make sure the tire valve stem is positioned close to the ground so the hose will reach it.

8. Press and turn the selector

switch (1) counterclockwise to the Sealant + Air position.

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (65,1)

The pressure gauge (3) may read higher than the actual tire pressure while the compressor is on. Turn the compressor off to get an accurate pressure reading. The compressor may be turned on/off until the correct pressure is reached.

{ Caution

If the recommended pressure cannot be reached after approximately 25 minutes, the vehicle should not be driven farther. The tire is too severely damaged and the tire sealant and compressor kit cannot inflate the tire. Remove the power plug from the accessory power outlet and unscrew the inflating hose from the tire valve. See Roadside Assistance Program on page 13-5.

11. Press the on/off button (2) to

turn the tire sealant and compressor kit off. The tire is not sealed and will continue to leak air until the vehicle is driven and the sealant is distributed in the tire; therefore, Steps 12–18 must be done immediately after Step 11. Be careful while handling the tire sealant and compressor kit as it could be warm after usage.

12. Unplug the power plug (8) from

the accessory power outlet in the vehicle.

13. Turn the sealant/air hose (6)

counterclockwise to remove it from the tire valve stem.

14. Replace the tire valve

stem cap.

15. Replace the sealant/air hose

(6), and the power plug (8) back in their original location.

Vehicle Care

10-65

16.

If the flat tire was able to inflate to the recommended inflation pressure, remove the maximum speed label from the sealant canister (5) and place it in a highly visible location. Do not exceed the speed on this label until the damaged tire is repaired or replaced.

17. Return the equipment to its

18.

original storage location in the vehicle. Immediately drive the vehicle 8 km (5 mi) to distribute the sealant in the tire.

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (66,1)

10-66

Vehicle Care

19. Stop at a safe location and

check the tire pressure. Refer to Steps 1–11 under “Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured).” If the tire pressure has fallen more than 68 kPa (10 psi) below the recommended inflation pressure, stop driving the vehicle. The tire is too severely damaged and the tire sealant cannot seal the tire. See Roadside Assistance Program on page 13-5. If the tire pressure has not dropped more than 68 kPa (10 psi) from the recommended inflation pressure, inflate the tire to the recommended inflation pressure.

20. Wipe off any sealant from the

wheel, tire, and vehicle.

21. Dispose of the used sealant canister (5) and sealant/air hose (6) assembly at a local dealer or in accordance with local state codes and practices.

22. Replace it with a new canister

available from your dealer.

23. After temporarily sealing a tire

using the tire sealant and compressor kit, take the vehicle to an authorized dealer within a 161 km (100 mi) of driving to have the tire repaired or replaced.

Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured) To use the air compressor to inflate a tire with air only and not sealant:

Chevrolet VOLT Owner Manual (GMNA-Localizing-U.S./Canada-7695131) - 2015 - CRC - 9/15/14

Black plate (67,1)

If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 6-3. See If a Tire Goes Flat on page 10-60 for other important safety warnings. 1. Remove the tire sealant and

compressor kit from its storage location. See Storing the Tire Sealant and Compressor Kit on page 10-69.

2. Unwrap the air only hose (7) and

the power plug (8).

3. Place the kit on the ground.

Make sure the tire valve stem is positioned close to the ground so the hose will reach it.

4. Remove the tire valve stem cap

from the flat tire by turning it counterclockwise.