Login- Download PDF Manual
-
Chevrolet SS Sedan Owner Manual (GMNA-Localizing-U.S.-9234782) - 2016 - CRC - 8/24/15
328
Vehicle Care
6. Slide the wheel wrench onto
the drive nut of the jack.
Caution
Make sure that the jack lift head is in the correct position or you may damage your vehicle. The repairs would not be covered by your warranty.
7. Position the jack lift head at the
8. Raise the vehicle by turning the
jack location nearest the flat tire. The locations are identified by cutouts in the underside of the door sill. The jack must not be used in any other position.
jack handle clockwise. Raise the vehicle far enough off the ground so there is enough room for the road tire to clear the ground.
Chevrolet SS Sedan Owner Manual (GMNA-Localizing-U.S.-9234782) - 2016 - CRC - 8/24/15
Warning (Continued)
towel can be used; however, use a scraper or wire brush later to remove all rust or dirt.
9. Remove all of the wheel nuts. 10. Remove the flat tire. { Warning
Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, a cloth or a paper (Continued)
11. Remove any rust or dirt from
the wheel bolts, mounting surfaces, and spare wheel. 12. Place the spare tire on the
wheel-mounting surface.
Vehicle Care
329
{ Warning
Never use oil or grease on bolts or nuts because the nuts might come loose. The vehicle's wheel could fall off, causing a crash.
13. Reinstall the wheel nuts.
Tighten each nut by hand until the wheel is held against the hub.
14. Lower the vehicle by turning
the jack handle counterclockwise.
{ Warning
Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing. Follow the torque specification supplied by the aftermarket manufacturer when using accessory locking wheel
(Continued)
Chevrolet SS Sedan Owner Manual (GMNA-Localizing-U.S.-9234782) - 2016 - CRC - 8/24/15
330
Vehicle Care
Warning (Continued)
nuts. See Capacities and Specifications 0 358
equipment wheel nut torque specifications.ii
for original
Caution
Improperly tightened wheel nuts can lead to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque specification. See Capacities and Specifications for the wheel nut torque 0 358
specification.ii
15. Tighten the wheel nuts firmly in
a crisscross sequence, as shown.
16. Lower the jack all the way and remove the jack from under the vehicle.
17. Tighten the wheel nuts firmly
with the wheel wrench.
Storing a Flat or Spare Tire and Tools
{ Warning
Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.
Replace the jack, tools, container and flat tire in the trunk by reversing the steps used to remove them.
Full-Size Spare Tire If this vehicle came with a full-size spare tire, it was fully inflated when new, however, it can lose air over time. Check the inflation pressure regularly. See Tire Pressure 0 305
and Vehicle Load Limits 0 223
for information regarding proper tire inflation and loading the vehicle. For instructions on how to remove, install, or store a spare tire, see Tire Changing 0 326ii
ii
ii
Chevrolet SS Sedan Owner Manual (GMNA-Localizing-U.S.-9234782) - 2016 - CRC - 8/24/15
After installing the spare tire on the vehicle, stop as soon as possible and check that the spare is correctly inflated. The spare tire is made to perform well at speeds up to 112 km/h (70 mph) at the recommended inflation pressure, so you can finish your trip. The full-size spare includes a TPMS sensor. The TPMS will not monitor or display the spare tire air pressure until the tire/wheel is installed at one of the four tire/wheel positions on the vehicle and matched to the new position. See Tire Pressure Monitor for information Operation 0 308
about matching the spare tire to the TPMS. Have the damaged or flat road tire repaired or replaced and installed back onto the vehicle as soon as possible so the spare tire will be available in case it is needed again. Do not mix tires and wheels of different sizes, because they will not fit. Keep the spare tire and its wheel together.ii
Jump Starting
Jump Starting - North America For more information about the vehicle battery, see Battery - North America 0 284
If the battery has run down, try to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely.ii
{ Warning WARNING: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Batteries also contain other chemicals known to the State of California to cause cancer. WASH HANDS AFTER HANDLING. See California Proposition 65 Warning 0 267
ii
Vehicle Care
331
{ Warning
Batteries can hurt you. They can be dangerous because:
. They contain acid that can
burn you.
. They contain gas that can
explode or ignite.
. They contain enough electricity to burn you.
If you do not follow these steps exactly, some or all of these things can hurt you.
Caution
Ignoring these steps could result in costly damage to the vehicle that would not be covered by the vehicle warranty. Trying to start the vehicle by pushing or pulling it will not work, and it could damage the vehicle.
Chevrolet SS Sedan Owner Manual (GMNA-Localizing-U.S.-9234782) - 2016 - CRC - 8/24/15
332
Vehicle Care
Caution
Caution (Continued)
If the other vehicle does not have a 12-volt system with a negative ground, both vehicles can be damaged. Only use a vehicle that has a 12-volt system with a negative ground for jump starting.
2. Position the two vehicles so
that they are not touching.
3. Set the parking brake firmly
and put the shift lever in P (Park) with an automatic transmission. See Shifting Into Park (Automatic Transmission) . Vehicles with a manual 0 230
transmission should be in Neutral. See Parking 0 232ii
ii
Caution
If any accessories are left on or plugged in during the jump starting procedure, they could be damaged. The repairs would not be covered by the vehicle
(Continued)
warranty. Whenever possible, turn off or unplug all accessories on either vehicle when jump starting.
4. Turn the ignition to LOCK/OFF
and switch off all lights and accessories in both vehicles, except the hazard warning flashers if needed. { Warning
An electric fan can start up even when the engine is not running and can injure you. Keep hands, clothing, and tools away from any underhood electric fan.
{ Warning
Using a match near a battery can cause battery gas to explode. People have been hurt doing this, (Continued)
1. Jump Start Positive Post 2. Jump Start Negative Post
The jump start positive (1) and negative (2) posts are in the engine compartment on the driver side of the vehicle. These posts are used instead of a direct connection to the battery. The positive jump start connection is covered by a red cap. Remove to expose the terminal. 1. Check the other vehicle.
It must have a 12-volt battery with a negative ground system.
Chevrolet SS Sedan Owner Manual (GMNA-Localizing-U.S.-9234782) - 2016 - CRC - 8/24/15
Warning (Continued)
and some have been blinded. Use a flashlight if you need more light. Battery fluid contains acid that can burn you. Do not get it on you. If you accidentally get it in your eyes or on your skin, flush the place with water and get medical help immediately.
{ Warning
6. Connect the other end of the
red positive (+) cable to the positive (+) terminal of the good battery.
7. Connect one end of the black
negative (–) cable to the negative (–) terminal of the good battery.
8. Connect the other end of the
black negative (–) cable to the remote negative (–) post (2).
9. Start the engine in the vehicle with the good battery and run the engine at idle speed for at least four minutes.
Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running.
10. Try to start the vehicle that had
the dead battery. If it will not start after a few tries, it probably needs service.
5. Connect one end of the red
positive (+) cable to the jump start remote positive (+) post (1) of the discharged battery.
Caution
If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be (Continued)
Vehicle Care
333
Caution (Continued)
covered by the vehicle warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.
Jumper Cable Removal Reverse the sequence exactly when removing the jumper cables After starting the disabled vehicle and removing the jumper cables, allow it to idle for several minutes.
Chevrolet SS Sedan Owner Manual (GMNA-Localizing-U.S.-9234782) - 2016 - CRC - 8/24/15
334
Vehicle Care
Towing the Vehicle
Caution
Incorrectly towing a disabled vehicle may cause damage. The damage would not be covered by the vehicle warranty. Do not lash or hook to suspension components. Use the proper straps around the tires to secure the vehicle.
Have the vehicle towed on a flatbed car carrier. A wheel lift tow truck could damage the vehicle. Consult your dealer or a professional towing service if the disabled vehicle must be towed.
There are two oval-shaped slots (1) under the front of the vehicle that should be used to move a disabled vehicle. Use only these slots to hook to the vehicle. The slots can be accessed through the splash shield. Use an appropriate size T hook for the slot. To tow the vehicle behind another vehicle for recreational purposes, such as behind a motor home, see “Recreational Vehicle Towing” following.
Recreational Vehicle Towing
Caution
Dolly towing or dinghy towing the vehicle may cause damage because of reduced ground clearance. Always put the vehicle on a flatbed truck or trailer.
The vehicle was neither designed nor intended to be towed with any of its wheels on the ground. If the vehicle must be towed, see Towing the Vehicle 0 334
ii
Chevrolet SS Sedan Owner Manual (GMNA-Localizing-U.S.-9234782) - 2016 - CRC - 8/24/15
Appearance Care
Exterior Care
Locks Locks are lubricated at the factory. Use a de-icing agent only when absolutely necessary, and have the locks greased after using. See Recommended Fluids and Lubricants 0 354
Washing the Vehicle To preserve the vehicle's finish, wash it often and out of direct sunlight.ii
Caution
Do not use petroleum-based, acidic, or abrasive cleaning agents as they can damage the vehicle's paint, metal, or plastic parts. If damage occurs, it would not be covered by the vehicle warranty. Approved cleaning products can be obtained from
(Continued)
Caution (Continued)
your dealer. Follow all manufacturer directions regarding correct product usage, necessary safety precautions, and appropriate disposal of any vehicle care product.
Caution
Avoid using high-pressure washes closer than 30 cm (12 in) to the surface of the vehicle. Use of power washers exceeding 8,274 kPa (1,200 psi) can result in damage or removal of paint and decals.
This symbol e is on any underhood compartment electrical center that should not be power washed. This could cause damage that would not be covered by the vehicle warranty.
Vehicle Care
335
If using an automatic car wash, follow the car wash instructions. The windshield wiper and rear window wiper, if equipped, must be off. Remove any accessories that may be damaged or interfere with the car wash equipment. Rinse the vehicle well, before washing and after, to remove all cleaning agents completely. If they are allowed to dry on the surface, they could stain. Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting. Finish Care Application of aftermarket clearcoat sealant/wax materials is not recommended. If painted surfaces are damaged, see your dealer to have the damage assessed and repaired. Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage the vehicle's finish if they remain on painted surfaces. Wash
Chevrolet SS Sedan Owner Manual (GMNA-Localizing-U.S.-9234782) - 2016 - CRC - 8/24/15
336
Vehicle Care
the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter. Occasional hand waxing or mild polishing should be done to remove residue from the paint finish. See your dealer for approved cleaning products. Do not apply waxes or polishes to uncoated plastic, vinyl, rubber, decals, simulated wood, or flat paint as damage can occur.
Caution
Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/ clearcoat paint finish on the vehicle.
To keep the paint finish looking new, keep the vehicle garaged or covered whenever possible.
Protecting Exterior Bright Metal Moldings
Caution
Failure to clean and protect the bright metal moldings can result in a hazy white finish or pitting. This damage would not be covered by the vehicle warranty.
The bright metal moldings on the vehicle are aluminum, chrome or stainless steel. To prevent damage always follow these cleaning instructions: . Be sure the molding is cool to the touch before applying any cleaning solution.
. Use only approved cleaning
solutions for aluminum, chrome or stainless steel. Some cleaners are highly acidic or contain alkaline substances and can damage the moldings.
. Always dilute a concentrated
cleaner according to the manufacturer’s instructions.
. Do not use cleaners that are not
intended for automotive use.
. Use a nonabrasive wax on the vehicle after washing to protect and extend the molding finish.
Cleaning Exterior Lamps/ Lenses, Emblems, Decals, and Stripes Use only lukewarm or cold water, a soft cloth, and a car washing soap to clean exterior lamps, lenses, emblems, decals, and stripes. Follow instructions under "Washing the Vehicle" previously in this section. Lamp covers are made of plastic, and some have a UV protective coating. Do not clean or wipe them while they are dry. Do not use any of the following on lamp covers: . Abrasive or caustic agents. . Washer fluids and other cleaning
agents in higher concentrations than suggested by the manufacturer.
Chevrolet SS Sedan Owner Manual (GMNA-Localizing-U.S.-9234782) - 2016 - CRC - 8/24/15
Vehicle Care
337
. Solvents, alcohols, fuels, or other harsh cleaners. Ice scrapers or other hard items. . Aftermarket appearance caps or
covers while the lamps are illuminated, due to excessive heat generated.
Caution
Failure to clean lamps properly can cause damage to the lamp cover that would not be covered by the vehicle warranty.
Caution
Using wax on low gloss black finish stripes can increase the gloss level and create a non-uniform finish. Clean low gloss stripes with soap and water only.
Air Intakes Clear debris from the air intakes, hood vents, and between the hood and windshield, when washing the vehicle. Windshield and Wiper Blades Clean the outside of the windshield with glass cleaner. Clean rubber blades using a lint-free cloth or paper towel soaked with windshield washer fluid or a mild detergent. Wash the windshield thoroughly when cleaning the blades. Bugs, road grime, sap, and a buildup of vehicle wash/wax treatments may cause wiper streaking. Replace the wiper blades if they are worn or damaged. Damage can be caused by extreme dusty conditions, sand, salt, heat, sun, snow, and ice. Weatherstrips Apply Dielectric silicone grease on weatherstrips to make them last longer, seal better, and not stick or squeak. Lubricate weatherstrips at
least once a year. Hot, dry climates may require more frequent application. Black marks from rubber material on painted surfaces can be removed by rubbing with a clean cloth. See Recommended Fluids and Lubricants 0 354
Tires Use a stiff brush with tire cleaner to clean the tires.ii
Caution
Using petroleum-based tire dressing products on the vehicle may damage the paint finish and/ or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on the vehicle.
Wheels and Trim — Aluminum or Chrome Use a soft, clean cloth with mild soap and water to clean the wheels. After rinsing thoroughly with clean water, dry with a soft, clean towel. A wax may then be applied.
Chevrolet SS Sedan Owner Manual (GMNA-Localizing-U.S.-9234782) - 2016 - CRC - 8/24/15
338
Vehicle Care
Caution
Caution (Continued)
Chrome wheels and other chrome trim may be damaged if the vehicle is not washed after driving on roads that have been sprayed with magnesium, calcium, or sodium chloride. These chlorides are used on roads for conditions such as ice and dust. Always wash the chrome with soap and water after exposure.
Caution
To avoid surface damage, do not use strong soaps, chemicals, abrasive polishes, cleaners, brushes, or cleaners that contain acid on aluminum or chrome-plated wheels. Use only approved cleaners. Also, never drive a vehicle with aluminum or chrome-plated wheels through an automatic car wash that uses silicone carbide tire cleaning
(Continued)
brushes. Damage could occur and the repairs would not be covered by the vehicle warranty.
Door Drain Holes
. Clear dirt and other foreign
materials from the drain holes at the bottom of the door panels which could trap water inside the panels.
. Clean clogged drain holes. . Avoid scratching the finish.
Brake System Visually inspect brake lines and hoses for proper hook-up, binding, leaks, cracks, chafing, etc. Inspect disc brake pads for wear and rotors for surface condition. Inspect drum brake linings/shoes for wear or cracks. Inspect other brake parts, including drums, wheel cylinders, calipers, parking brake, master cylinder, brake fluid reservoir, vacuum pipes, electric vacuum pump including bracket and vent hose, if equipped. Steering, Suspension, and Chassis Components Visually inspect steering, suspension, and chassis components for damaged, loose, or missing parts or signs of wear at least once a year. Inspect power steering for proper hook-up, binding, leaks, cracks, chafing, etc. Visually check constant velocity joint boots and axle seals for leaks.
Chevrolet SS Sedan Owner Manual (GMNA-Localizing-U.S.-9234782) - 2016 - CRC - 8/24/15
Body Component Lubrication Lubricate all key lock cylinders, hood hinges, liftgate hinges, steel fuel door hinge, decklid spring bushings, and power assist step hinges, unless the components are plastic. Applying silicone grease on weatherstrips with a clean cloth will make them last longer, seal better, and not stick or squeak. Underbody Maintenance At least twice a year, spring and fall, use plain water to flush any corrosive materials from the underbody. Take care to thoroughly clean any areas where mud and other debris can collect. Do not directly power wash the transfer case and/or front/rear axle output seals. High pressure water can overcome the seals and contaminate the fluid. Contaminated fluid will decrease the life of the transfer case and/or axles and should be replaced.
Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the vehicle warranty. Finish Damage Quickly repair minor chips and scratches with touch-up materials available from your dealer to avoid corrosion. Larger areas of finish damage can be corrected in your dealer's body and paint shop. Chemical Paint Spotting Airborne pollutants can fall upon and attack painted vehicle surfaces causing blotchy, ring-shaped discolorations, and small, irregular dark spots etched into the paint surface. Refer to “Finish Care” previously in this section.
Vehicle Care
339
Interior Care To prevent dirt particle abrasions, regularly clean the vehicle's interior. Immediately remove any soils. Newspapers or dark garments can transfer color to the vehicle’s interior. Use a soft bristle brush to remove dust from knobs and crevices on the instrument cluster. Using a mild soap solution, immediately remove hand lotions, sunscreen, and insect repellent from all interior surfaces or permanent damage may result. Use cleaners specifically designed for the surfaces being cleaned to prevent permanent damage. Apply cleaners directly to the cleaning cloth. Do not spray cleaners on any switches or controls. Remove cleaners quickly. Before using cleaners, read and follow all safety instructions on the label. While cleaning the interior, open the doors and windows to get proper ventilation.
Chevrolet SS Sedan Owner Manual (GMNA-Localizing-U.S.-9234782) - 2016 - CRC - 8/24/15
340
Vehicle Care
To prevent damage, do not clean the interior using the following cleaners or techniques: . Never use a razor or any other
sharp object to remove a soil from any interior surface.
. Never use a brush with stiff
bristles.
. Never rub any surface
aggressively or with too much pressure.
. Do not use laundry detergents or
dishwashing soaps with degreasers. For liquid cleaners, use approximately 20 drops per 3.8 L (1 gal) of water. A concentrated soap solution will create streaks and attract dirt. Do not use solutions that contain strong or caustic soap.
. Do not heavily saturate the upholstery when cleaning.
. Do not use solvents or cleaners
containing solvents.
Interior Glass To clean, use a terry cloth fabric dampened with water. Wipe droplets left behind with a clean dry cloth. If necessary, use a commercial glass cleaner after cleaning with plain water.
Caution
To prevent scratching, never use abrasive cleaners on automotive glass. Abrasive cleaners or aggressive cleaning may damage the rear window defogger.
Cleaning the windshield with water during the first three to six months of ownership will reduce tendency to fog. Speaker Covers Vacuum around a speaker cover gently, so that the speaker will not be damaged. Clean spots with water and mild soap.
Coated Moldings Coated moldings should be cleaned. . When lightly soiled, wipe with a
sponge or soft lint-free cloth dampened with water.
. When heavily soiled, use warm
soapy water.
Fabric/Carpet/Suede Start by vacuuming the surface using a soft brush attachment. If a rotating vacuum brush attachment is being used, only use it on the floor carpet. Before cleaning, gently remove as much of the soil as possible: . Gently blot liquids with a paper towel. Continue blotting until no more soil can be removed.
. For solid soils, remove as much as possible prior to vacuuming.
To clean: 1. Saturate a clean lint-free colorfast cloth with water. Microfiber cloth is recommended to prevent lint transfer to the fabric or carpet.
Chevrolet SS Sedan Owner Manual (GMNA-Localizing-U.S.-9234782) - 2016 - CRC - 8/24/15
Cleaning High Gloss Surfaces and Vehicle Information and Radio Displays Use a microfiber cloth on high gloss surfaces or vehicle displays. First, use a soft bristle brush to remove dirt that can scratch the surface. Then gently clean by rubbing with a microfiber cloth. Never use window cleaners or solvents. Periodically hand wash the microfiber cloth separately, using mild soap. Do not use bleach or fabric softener. Rinse thoroughly and air dry before next use.
Caution
Do not attach a device with a suction cup to the display. This may cause damage and would not be covered by the vehicle warranty.
2. Remove excess moisture by
gently wringing until water does not drip from the cleaning cloth. 3. Start on the outside edge of the
soil and gently rub toward the center. Fold the cleaning cloth to a clean area frequently to prevent forcing the soil in to the fabric.
4. Continue gently rubbing the soiled area until there is no longer any color transfer from the soil to the cleaning cloth. If the soil is not completely removed, use a mild soap solution followed only by plain water.
5.
If the soil is not completely removed, it may be necessary to use a commercial upholstery cleaner or spot lifter. Test a small hidden area for colorfastness before using a commercial upholstery cleaner or spot lifter. If ring formation occurs, clean the entire fabric or carpet. After cleaning use a paper towel to blot excess moisture.
Vehicle Care
341
Instrument Panel, Leather, Vinyl, Other Plastic Surfaces, Low Gloss Paint Surfaces and Natural Open Pore Wood Surfaces Use a soft microfiber cloth dampened with water to remove dust and loose dirt. For a more thorough cleaning, use a soft microfiber cloth dampened with a mild soap solution.
Caution
Soaking or saturating leather, especially perforated leather, as well as other interior surfaces, may cause permanent damage. Wipe excess moisture from these surfaces after cleaning and allow them to dry naturally. Never use heat, steam, or spot removers. Do not use cleaners that contain silicone or wax-based products. Cleaners containing these solvents can permanently change (Continued)
Chevrolet SS Sedan Owner Manual (GMNA-Localizing-U.S.-9234782) - 2016 - CRC - 8/24/15
342
Vehicle Care
Caution (Continued)
the appearance and feel of leather or soft trim, and are not recommended.
Do not use cleaners that increase gloss, especially on the instrument panel. Reflected glare can decrease visibility through the windshield under certain conditions.
Caution
Use of air fresheners may cause permanent damage to plastics and painted surfaces. If an air freshener comes in contact with any plastic or painted surface in the vehicle, blot immediately and clean with a soft cloth dampened with a mild soap solution. Damage caused by air fresheners would not be covered by the vehicle warranty.
Convenience Net If equipped with a convenience net, wash with warm water and mild detergent. Do not Use chlorine bleach. Rinse with cold water, and then dry completely. Care of Safety Belts Keep belts clean and dry. { Warning
Do not bleach or dye safety belts. It may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.
Floor Mats
{ Warning
If a floor mat is the wrong size or is not properly installed, it can interfere with the pedals. Interference with the pedals can
(Continued)
Warning (Continued)
cause unintended acceleration and/or increased stopping distance which can cause a crash and injury. Make sure the floor mat does not interfere with the pedals.
Use the following guidelines for proper floor mat usage (if equipped): . The original equipment floor mats were designed for your vehicle. If the floor mats need replacing, it is recommended that GM certified floor mats be purchased. Non-GM floor mats may not fit properly and may interfere with the pedals. Always check that the floor mats do not interfere with the pedals.
. Do not use a floor mat if the
vehicle is not equipped with a floor mat retainer on the driver side floor.
. Use the floor mat with the
correct side up. Do not turn it over.
Chevrolet SS Sedan Owner Manual (GMNA-Localizing-U.S.-9234782) - 2016 - CRC - 8/24/15
Vehicle Care
343
Make sure the floor mat is properly secured in place. Verify the floor mat does not interfere with the pedals.
. Do not place anything on top of
the driver side floor mat.
. Use only a single floor mat on
the driver side.
. Do not place one floor mat on
top of another.
Removing and Replacing the Floor Mats Pull up on the rear of the floor mat to unlock each retainer and remove.
Reinstall by lining up the floor mat retainer openings over the carpet retainers and snap into position.
Chevrolet SS Sedan Owner Manual (GMNA-Localizing-U.S.-9234782) - 2016 - CRC - 8/24/15
Service and Maintenance
344
Service and MaintenanceGeneral Information
General Information . . . . . . . . . . 344
Maintenance Schedule
Maintenance Schedule . . . . . . . 346
Special Application Services
Special Application
Services . . . . . . . . . . . . . . . . . . . . 351
Additional Maintenance and Care
Additional Maintenance
and Care . . . . . . . . . . . . . . . . . . . . 351
Recommended Fluids
Recommended Fluids and
Lubricants . . . . . . . . . . . . . . . . . . . 354
Maintenance Replacement
Parts . . . . . . . . . . . . . . . . . . . . . . . . 355
Maintenance Records
Maintenance Records . . . . . . . . 356
General Information Your vehicle is an important investment. This section describes the required maintenance for the vehicle. Follow this schedule to help protect against major repair expenses resulting from neglect or inadequate maintenance. It may also help to maintain the value of the vehicle if it is sold. It is the responsibility of the owner to have all required maintenance performed. Your dealer has trained technicians who can perform required maintenance using genuine replacement parts. They have up-to-date tools and equipment for fast and accurate diagnostics. Many dealers have extended evening and Saturday hours, courtesy transportation, and online scheduling to assist with service needs.
Your dealer recognizes the importance of providing competitively priced maintenance and repair services. With trained technicians, the dealer is the place for routine maintenance such as oil changes and tire rotations and additional maintenance items like tires, brakes, batteries, and wiper blades.
Caution
Damage caused by improper maintenance can lead to costly repairs and may not be covered by the vehicle warranty. Maintenance intervals, checks, inspections, recommended fluids, and lubricants are important to keep the vehicle in good working condition.
Chevrolet SS Sedan Owner Manual (GMNA-Localizing-U.S.-9234782) - 2016 - CRC - 8/24/15
Service and Maintenance
345
{ Warning
Performing maintenance work can be dangerous and can cause serious injury. Perform maintenance work only if the required information, proper tools, and equipment are available. If they are not, see your dealer to have a trained technician do the work. See Doing Your Own Service Work 0 268
ii
Refer to the information in the Maintenance Schedule Additional Required Services - Normal chart. The Additional Required Services - Severe are for vehicles that are: . Mainly driven in heavy city traffic
in hot weather.
. Mainly driven in hilly or
mountainous terrain.
. Frequently towing a trailer. . Used for high speed or
competitive driving.
. Used for taxi, police, or delivery
service.
Refer to the information in the Maintenance Schedule Additional Required Services - Severe chart.
The Tire Rotation and Required Services are the responsibility of the vehicle owner. It is recommended to have your dealer perform these services every 12 000 km/7,500 mi. Proper vehicle maintenance helps to keep the vehicle in good working condition, improves fuel economy, and reduces vehicle emissions. Because of the way people use vehicles, maintenance needs vary. There may need to be more frequent checks and services. The Additional Required Services - Normal are for vehicles that: . Carry passengers and cargo within recommended limits on the Tire and Loading Information label. See Vehicle Load Limits 0 223
ii
. Are driven on reasonable road
surfaces within legal driving limits.
. Use the recommended fuel. See
Fuel 0 261
ii
Chevrolet SS Sedan Owner Manual (GMNA-Localizing-U.S.-9234782) - 2016 - CRC - 8/24/15
346
Service and Maintenance
Maintenance Schedule
Owner Checks and Services
At Each Fuel Stop . Check the engine oil level. See
Engine Oil 0 271
ii
Once a Month . Check the tire inflation
pressures. See Tire Pressure 0 305
Inspect the tires for wear. See Tire Inspection 0 311ii
ii
. Check the windshield washer fluid level. See Washer Fluid 0 282
ii
Engine Oil Change When the CHANGE ENGINE OIL SOON message displays, have the engine oil and filter changed within the next 1 000 km/600 mi. If driven under the best conditions, the
engine oil life system may not indicate the need for vehicle service for up to a year. The engine oil and filter must be changed at least once a year and the oil life system must be reset. Your trained dealer technician can perform this work. If the engine oil life system is reset accidentally, service the vehicle within 5 000 km/3,000 mi since the last service. Reset the oil life system when the oil is changed. See Engine Oil Life System 0 273
Tire Rotation and Required Services Every 12 000 km/ 7,500 mi Rotate the tires, if recommended for the vehicle, and perform the following services. See Tire Rotation 0 311
. Check engine oil level and oilii
ii
life percentage. If needed, change engine oil and filter, and reset oil life system. See Engine Oil 0 271
System 0 273and Engine Oil Life
ii
ii
. Check engine coolant level. See
Engine Coolant 0 277
ii
. Check windshield washer fluid level. See Washer Fluid 0 282
ii
. Visually inspect windshield wiper
blades for wear, cracking, or contamination. See Exterior . Replace worn or Care 0 335
damaged wiper blades. See Wiper Blade Replacement 0 287ii
ii
. Check tire inflation pressures.
See Tire Pressure 0 305
ii
. Check spare wheel retainer. If loose, tighten with a torque wrench to 4.5 +/− 0.5 Y. Inspect tire wear. See Tire Inspection 0 311
ii
. Visually check for fluid leaks.
Inspect engine air cleaner filter. See Engine Air Cleaner/Filter 0 275
ii
Chevrolet SS Sedan Owner Manual (GMNA-Localizing-U.S.-9234782) - 2016 - CRC - 8/24/15
Service and Maintenance
347
Inspect brake system. See Exterior Care 0 335
ii
. Visually inspect steering, suspension, and chassis components for damaged, loose, or missing parts or signs of wear. See Exterior Care 0 335
ii
. Check restraint system
components. See Safety System Check 0 54
ii
. Visually inspect fuel system for
damage or leaks.
. Visually inspect exhaust system
. Check parking brake and
and nearby heat shields for loose or damaged parts.
. Lubricate body components. See
Exterior Care 0 335
ii
. Check starter switch. See Starter
Switch Check 0 286
ii
. Check automatic transmission shift lock control function. See Automatic Transmission Shift Lock Control Function Check 0 286
ii
automatic transmission park mechanism. See Park Brake and P (Park) Mechanism Check 0 287
ii
. Check accelerator pedal for
damage, high effort, or binding. Replace if needed.
. Visually inspect gas strut for
signs of wear, cracks, or other damage. Check the hold open ability of the strut. See your dealer if service is required.
Chevrolet SS Sedan Owner Manual (GMNA-Localizing-U.S.-9234782) - 2016 - CRC - 8/24/15
348
Service and Maintenance
Maintenance Schedule Additional Required Services - Normal
Rotate tires and perform Required Services. Check engine oil level and oil life percentage. Change engine oil and filter, if needed.
@ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @
Replace passenger compartment air filter. (1)
Inspect evaporative control system. (2)
Replace engine air cleaner filter. (3)
Replace spark plugs. Inspect spark plug wires.
Drain and fill engine cooling system. (4)
Visually inspect accessory drive belts. (5)
Replace rear axle fluid.
Replace brake fluid. (6)
Chevrolet SS Sedan Owner Manual (GMNA-Localizing-U.S.-9234782) - 2016 - CRC - 8/24/15
Service and Maintenance
349
(2) Check all fuel and vapor lines and hoses for proper hook-up, routing, and condition. (3) Or every four years, whichever comes first. If driving in dusty conditions, inspect the filter at each oil change or more often as needed. (4) Or every five years, whichever comes first. See Cooling System 0 276
ii
(5) Or every 10 years, whichever comes first. Inspect for fraying, excessive cracking, or damage; replace, if needed. (6) Replace brake fluid every three years. See Brake Fluid 0 283
ii
Footnotes — Maintenance Schedule Additional Required Services - Normal (1) Or every two years, whichever comes first. More frequent passenger compartment air filter replacement may be needed if driving in areas with heavy traffic, poor air quality, high dust levels, or environmental allergens. Passenger compartment air filter replacement may also be needed if there is reduced airflow, window fogging, or odors. Your GM dealer can help determine when to replace the filter.
Chevrolet SS Sedan Owner Manual (GMNA-Localizing-U.S.-9234782) - 2016 - CRC - 8/24/15
350
Service and Maintenance
Maintenance Schedule Additional Required Services - Severe
Rotate tires and perform Required Services. Check engine oil level and oil life percentage. Change engine oil and filter, if needed.
