2014 Chevrolet Silverado Owners Manual

Vehicle Care

10-65

using a TPMS relearn tool, in the following order: driver side front tire, passenger side front tire, passenger side rear tire, and driver side rear. See your dealer for service or to purchase a relearn tool. There are two minutes to match the first tire/wheel position, and five minutes overall to match all four tire/wheel positions. If it takes longer, the matching process stops and must be restarted. The TPMS sensor matching process is: 1. Set the parking brake. 2. Turn the ignition to ON/RUN with

the engine off.

3. Uplevel DIC Only: Make sure the Tire Pressure info page option is turned on. The info pages on the DIC can be turned on and off through the Settings menu. See Driver Information Center (DIC) (Base Level) on page 5-30 or Driver Information Center (DIC) (Uplevel) on page 5-32.

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (66,1)

10-66

Vehicle Care

4.

5.

If the vehicle has an uplevel DIC, use the DIC controls on the right side of the steering wheel to scroll to the Tire Pressure screen under the DIC info page. If the vehicle has a base level DIC, use the trip odometer reset stem to scroll to the Tire Pressure screen. If the vehicle has an uplevel DIC, press and hold the V (Set/ Reset) button located in the center of the DIC controls. If the vehicle has a base level DIC, press and hold the trip odometer reset stem for about five seconds. A message asking if the process should begin should appear. Select yes and press the trip odometer reset stem to confirm the selection. The horn sounds twice to signal the receiver is in relearn mode and the TIRE LEARNING ACTIVE message displays on the DIC screen.

6. Start with the driver side

11. Turn the ignition switch to

front tire.

LOCK/OFF.

7. Place the relearn tool against

12. Set all four tires to the

the tire sidewall, near the valve stem. Then press the button to activate the TPMS sensor. A horn chirp confirms that the sensor identification code has been matched to this tire and wheel position.

8. Proceed to the passenger side

front tire, and repeat the procedure in Step 7.

9. Proceed to the passenger side

rear tire, and repeat the procedure in Step 7.

10. Proceed to the driver side rear tire, and repeat the procedure in Step 7. The horn sounds two times to indicate the sensor identification code has been matched to the driver side rear tire, and the TPMS sensor matching process is no longer active. The TIRE LEARNING ACTIVE message on the DIC display screen goes off.

recommended air pressure level as indicated on the Tire and Loading Information label.

Tire Inspection We recommend that the tires, including the spare tire, if the vehicle has one, be inspected for signs of wear or damage at least once a month. Replace the tire if: . The indicators at three or

more places around the tire can be seen.

. There is cord or fabric

showing through the tire's rubber.

. The tread or sidewall is

cracked, cut, or snagged deep enough to show cord or fabric.

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (67,1)

Vehicle Care

10-67

. The tire has a bump, bulge,

or split.

. The tire has a puncture, cut, or other damage that cannot be repaired well because of the size or location of the damage.

Tire Rotation Tires should be rotated every 12 000 km (7,500 mi). See Maintenance Schedule on page 11-3. Tires are rotated to achieve a uniform wear for all tires. The first rotation is the most important. Anytime unusual wear is noticed, rotate the tires as soon as possible, check for proper tire inflation pressure, and check for damaged tires or wheels. If the unusual wear continues after the rotation, check the wheel

alignment. See When It Is Time for New Tires on page 10-69
and Wheel Replacement on page 10-74. If your vehicle has dual rear wheels, also see Dual Tire Rotation on page 10-69.

Use this rotation pattern when rotating the tires if the vehicle has dual rear wheels (except polished forged aluminum wheels). Vehicles with polished forged aluminum dual wheels have three unique wheels; a front, a rear outer and a rear inner. These wheels cannot be rotated to another position, however, they can be rotated from left to right to the same position.

Use this rotation pattern when rotating the tires if the vehicle has single rear wheels.

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (68,1)

10-68

Vehicle Care

Loading Information label after the tires have been rotated. See Tire Pressure on page 10-61
and Vehicle Load Limits on page 9-15. Check that all wheel nuts are properly tightened. See “Wheel Nut Torque” under Capacities and Specifications on page 12-2.

{ Warning

Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, a cloth or a paper towel can be used; however, use a scraper or wire brush later to remove all rust or dirt.

Lightly coat the center of the wheel hub with wheel bearing grease after a wheel change or tire rotation to prevent corrosion or rust build-up. Do not get grease on the flat wheel mounting surface or on the wheel nuts or bolts. Reset the Tire Pressure Monitor System (TPMS), if the vehicle has one. See Tire Pressure Monitor Operation on page 10-63. Check that the spare tire, if the vehicle has one, is stored properly. Push, pull, and then try to rotate or turn the tire. If it moves, tighten the cable. See “Storing a Flat or Spare Tire and Tools” under Tire Changing on page 10-78.

Use this rotation pattern when rotating the tires if the vehicle has polished forged aluminum dual rear wheels. The spare wheel can be used in any position and can be rotated with the rear inner wheels. When installing dual wheels, check that the vent holes in the inner and outer wheels on each side are lined up. Adjust the front and rear tires to the recommended inflation pressure on the Tire and

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (69,1)

Vehicle Care

10-69

Dual Tire Rotation When the vehicle is new, or whenever a wheel, wheel bolt, or wheel nut is replaced, check the wheel nut torque after 160, 1 600, and 10 000 km (100, 1,000, and 6,000 mi) of driving. For proper torque and wheel nut tightening information, see “Removing the Flat Tire and Installing the Spare Tire” under Tire Changing on page 10-78. The outer tire on a dual wheel setup generally wears faster than the inner tire. Tires last longer and wear more evenly if they are rotated. See Tire Inspection on page 10-66 and Tire Rotation on page 10-67. Also see Maintenance Schedule on page 11-3.

{ Warning

If the vehicle is operated with a tire that is underinflated, the tire can overheat. An overheated tire can lose air suddenly or catch fire. You or others could be injured. Properly inflate all tires, including the spare.

See Tire Pressure on page 10-61, for information on proper tire inflation.

When It Is Time for New Tires Factors, such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions affect the wear rate of the tires.

Treadwear indicators are one way to tell when it is time for new tires. Treadwear indicators appear when the tires have only 1.6 mm (1/16 in) or less of tread remaining. Some commercial truck tires may not have treadwear indicators. See Tire Inspection on page 10-66 and Tire Rotation on page 10-67 for additional information. The rubber in tires ages over time. This also applies to the spare tire, if the vehicle has one, even if it is never used. Multiple factors including temperatures, loading conditions, and inflation pressure

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (70,1)

10-70

Vehicle Care

maintenance affect how fast aging takes place. GM recommends that tires, including the spare if equipped, be replaced after six years, regardless of tread wear. The tire manufacturer date is the last four digits of the DOT Tire Identification Number (TIN) which is molded into one side of the tire sidewall. The first two digits represent the week (01-52) and the last two digits, the year. For example, the third week of the year 2010 would have a four-digit DOT date of 0310. Vehicle Storage Tires age when stored normally mounted on a parked vehicle. Park a vehicle that will be stored for at least a month in a cool, dry, clean area away from direct sunlight to slow aging. This area should be free of grease, gasoline or other substances that can deteriorate rubber.

Parking for an extended period can cause flat spots on the tires that may result in vibrations while driving. When storing a vehicle for at least a month, remove the tires or raise the vehicle to reduce the weight from the tires.

Buying New Tires GM has developed and matched specific tires for the vehicle. The original equipment tires installed were designed to meet General Motors Tire Performance Criteria Specification (TPC Spec) system rating. When replacement tires are needed, GM strongly recommends buying tires with the same TPC Spec rating. GM's exclusive TPC Spec system considers over a dozen critical specifications that impact the overall performance of the vehicle, including brake system performance, ride and handling,

traction control, and tire pressure monitoring performance. GM's TPC Spec number is molded onto the tire's sidewall near the tire size. If the tires have an all-season tread design, the TPC Spec number will be followed by MS for mud and snow. See Tire Sidewall Labeling on page 10-54 for additional information. GM recommends replacing worn tires in complete sets of four (six for dual rear wheels). Uniform tread depth on all tires will help to maintain the performance of the vehicle. Braking and handling performance may be adversely affected if all the tires are not replaced at the same time. If proper rotation and maintenance have been done, all four tires (six for dual rear wheels) should wear out at about the same time. See Tire Rotation on page 10-67 for

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (71,1)

Warning (Continued)

resulting in a crash or other vehicle damage. Use the correct size, brand, and type of tires on all wheels. This vehicle may have a different size spare than the road tires originally installed on the vehicle. When new, the vehicle included a spare tire and wheel assembly with a similar overall diameter as the road tires and wheels, so it is all right to drive on it. The spare tire was developed for use on this vehicle and will not affect vehicle handling.

information on proper tire rotation. However, if it is necessary to replace only one axle set of worn tires, place the new tires on the rear axle (two for single rear wheels, four for dual rear wheels).

{ Warning

Tires could explode during improper service. Attempting to mount or dismount a tire could cause injury or death. Only your dealer or authorized tire service center should mount or dismount the tires.

{ Warning

Mixing tires of different sizes, brands, or types may cause loss of control of the vehicle,

(Continued)

Vehicle Care

10-71

{ Warning

Using bias-ply tires on the vehicle may cause the wheel rim flanges to develop cracks after many miles of driving. A tire and/or wheel could fail suddenly and cause a crash. Use only radial-ply tires with the wheels on the vehicle.

If the vehicle tires must be replaced with a tire that does not have a TPC Spec number, make sure they are the same size, load range, speed rating, and construction (radial) as the original tires. Vehicles that have a tire pressure monitoring system could give an inaccurate low-pressure warning if non-TPC Spec rated tires are installed. See Tire Pressure Monitor System on page 10-62.

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (72,1)

10-72

Vehicle Care

The Tire and Loading Information label indicates the original equipment tires on the vehicle. See Vehicle Load Limits on page 9-15 for the label location and more information about the Tire and Loading Information label.

Different Size Tires and Wheels If wheels or tires are installed that are a different size than the original equipment wheels and tires, vehicle performance, including its braking, ride and handling characteristics, stability, and resistance to rollover may be affected. If the vehicle has electronic systems such as antilock brakes, rollover airbags, traction control, electronic stability control, or All-Wheel Drive, the performance of these systems can also be affected.

{ Warning

If different sized wheels are used, there may not be an acceptable level of performance and safety if tires not recommended for those wheels are selected. This increases the chance of a crash and serious injury. Only use GM specific wheel and tire systems developed for the vehicle, and have them properly installed by a GM certified technician.

See Buying New Tires on page 10-70 and Accessories and Modifications on page 10-3.

Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example:

Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration (NHTSA), which grades tires by treadwear, traction, and temperature performance. This applies only to vehicles sold in the United States. The grades are molded on the sidewalls of most passenger car tires. The Uniform Tire Quality Grading (UTQG) system does not apply to deep tread, winter tires, compact spare tires, tires with

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (73,1)

nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-production tires. While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades, they must also conform to federal safety requirements and additional General Motors Tire Performance Criteria (TPC) standards. All Passenger Car Tires Must Conform to Federal Safety Requirements In Addition To These Grades.

Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire

graded 150 would wear one and one-half (1½) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.

Traction The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warning: The traction grade assigned to this tire is based on

Vehicle Care

10-73

straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.

Temperature The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Safety Standard No. 109. Grades B and A represent higher levels of

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (74,1)

10-74

Vehicle Care

performance on the laboratory test wheel than the minimum required by law. Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.

Wheel Alignment and Tire Balance The tires and wheels were aligned and balanced at the factory to provide the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing are not necessary on a regular basis. Consider an alignment check if there is unusual tire wear or the vehicle is significantly pulling to one side or the other. Some slight pull to the left or right, depending on the crown of the road and/or other road

surface variations such as troughs or ruts, is normal. If the vehicle is vibrating when driving on a smooth road, the tires and wheels may need to be rebalanced. See your dealer for proper diagnosis.

Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts and wheel nuts should be replaced. If the wheel leaks air, replace it. Some aluminum wheels can be repaired. See your dealer if any of these conditions exist. Your dealer will know the kind of wheel that is needed. Each new wheel should have the same load-carrying capacity, diameter, width, offset and be mounted the same way as the one it replaces.

Replace wheels, wheel bolts, wheel nuts, or Tire Pressure Monitor System (TPMS) sensors with new GM original equipment parts.

{ Warning

Using the wrong replacement wheels, wheel bolts, or wheel nuts can be dangerous. It could affect the braking and handling of the vehicle. Tires can lose air, and cause loss of control, causing a crash. Always use the correct wheel, wheel bolts, and wheel nuts for replacement.

{ Caution

The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, bumper height, vehicle

(Continued)

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (75,1)

Vehicle Care

10-75

Caution (Continued)

Warning (Continued)

Warning (Continued)

ground clearance, and tire or tire chain clearance to the body and chassis.

Whenever a wheel, wheel bolt, or wheel nut is replaced on a dual wheel setup, check the wheel nut torque after 160, 1 600 and 10 000 km (100, 1,000 and 6,000 mi) of driving. For proper torque, see “Wheel Nut Torque” under Capacities and Specifications on page 12-2. See If a Tire Goes Flat on page 10-76 for more information.

Used Replacement Wheels

{ Warning

Replacing a wheel with a used one is dangerous. How it has been used or how far it has been (Continued)

driven may be unknown. It could fail suddenly and cause a crash. When replacing wheels, use a new GM original equipment wheel.

Tire Chains

{ Warning

If the vehicle has dual wheels or P265/65R18, P275/55R20, LT265/70R17, LT265/70R18, LT265/60R20, P285/50R20, P285/45R22 or 285/45R22 size tires, do not use tire chains. They can damage the vehicle because there is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle parts. The area damaged (Continued)

by the tire chains could cause you to lose control of the vehicle and you or others may be injured in a crash. Use another type of traction device only if its manufacturer recommends it for use on the vehicle and tire size combination and road conditions. Follow that manufacturer's instructions. To help avoid damage to the vehicle, drive slowly, readjust, or remove the device if it is contacting the vehicle, and do not spin the vehicle's wheels. If you do find traction devices that will fit, install them on the rear tires.

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (76,1)

10-76

Vehicle Care

{ Caution

If the vehicle does not have dual wheels and has a tire size other than P265/65R18, P275/55R20, LT265/70R17, LT265/70R18, LT265/60R20, P285/50R20, P285/45R22, or 285/45R22, use tire chains only where legal and only when necessary. Use chains that are the proper size for the tires. Install them on the tires of the rear axle. Do not use chains on the tires of the front axle. Tighten them as tightly as possible with the ends securely fastened. Drive slowly and follow the chain manufacturer's instructions. If the chains contact the vehicle, stop and retighten them. If the contact continues, slow down until it stops. Driving too fast or spinning the wheels with chains on will damage the vehicle.

If a Tire Goes Flat It is unusual for a tire to blowout while driving, especially if the tires are maintained properly. If air goes out of a tire, it is much more likely to leak out slowly. But if there ever is a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire creates a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly. Steer to maintain lane position, and then gently brake to a stop, well off the road, if possible. A rear blowout, particularly on a curve, acts much like a skid and may require the same correction as used in a skid. Stop pressing the accelerator pedal and steer to straighten the vehicle. It may be very bumpy and noisy. Gently brake to a stop, well off the road, if possible.

{ Warning

Driving on a flat tire will cause permanent damage to the tire. Re-inflating a tire after it has been driven on while severely underinflated or flat may cause a blowout and a serious crash. Never attempt to re-inflate a tire that has been driven on while severely underinflated or flat. Have your dealer or an authorized tire service center repair or replace the flat tire as soon as possible.

{ Warning

Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for (Continued)

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (77,1)

Vehicle Care

10-77

1. Wheel Block 2. Flat Tire The following information explains how to use the jack and change a tire.

Warning (Continued)

Warning (Continued)

changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. If a jack is provided with the vehicle, only use it for changing a flat tire.

If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place, well off the road, if possible. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 6-4.

{ Warning Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall causing injury or death. Find a level place to change the tire. To help prevent the vehicle from moving:

(Continued)

1. Set the parking brake firmly. 2. Put an automatic

transmission in P (Park) or a manual transmission in 1 (First) or R (Reverse).

3. For four-wheel-drive vehicles, be sure the transfer case is in a drive gear– not in N (Neutral).

4. Turn off the engine and do not restart while the vehicle is raised.

5. Do not allow passengers to

remain in the vehicle.

6. Place wheel blocks on both

sides of the tire at the opposite corner of the tire being changed.

When the vehicle has a flat tire (2), use the following example as a guide to assist in the placement of the wheel blocks (1).

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (78,1)

10-78

Vehicle Care

Tire Changing

Removing the Spare Tire and Tools

Crew Cab

1. Wheel Blocks 2. Wing Nut Retaining Tool Kit 3. Tool Kit 4. Wing Nut Retaining Wheel

Blocks

5. Jack 6. Jack Knob

Regular Cab

Double Cab

1. Wing Nut Retaining Wheel

Blocks

2. Wheel Blocks 3. Wing Nut Retaining Tool Kit 4. Tool Kit 5. Jack 6. Jack Knob

1. Wheel Blocks 2. Wing Nut Retaining Tool Kit 3. Tool Kit 4. Jack 5. Jack Knob For regular cab models, the equipment you will need is behind the passenger seat. For double and crew cab models, the equipment is on the shelf behind the passenger side second row seat.

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (79,1)

Vehicle Care

10-79

1. Open the spare tire lock cover

on the bumper and use the ignition key to remove the spare tire lock (10). To remove the spare tire lock, insert the ignition key turn and pull straight out.

2. Assemble the wheel wrench (7)

and the two jack handle extensions (6), as shown.

1. Turn the knob on the jack

counterclockwise to lower the jack head to release the jack from its holder.

2. Turn the wing nut

counterclockwise to remove the wheel blocks and the wheel block retainer.

3. Turn the wing nut used to retain

the storage bag and tools counterclockwise to remove it.

Use the jack handle extensions and the wheel wrench to remove the underbody-mounted spare tire.

1. Spare Tire (Valve Stem

Pointed Down)

2. Tire/Wheel Retainer 3. Hoist Cable 4. Hoist Assembly 5. Hoist Shaft 6. Jack Handle Extensions 7. Wheel Wrench 8. Spare Tire Lock (If Equipped) 9. Hoist Shaft Access Hole 10. Hoist End of Extension Tool

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (80,1)

10-80

Vehicle Care

5. Pull the spare tire out from under

the vehicle.

3.

Insert the hoist end (open end) (10) of the extension through the hole (9) in the rear bumper. Do not use the chiseled end of the wheel wrench. Be sure the hoist end of the extension (10) connects to the hoist shaft. The ribbed square end of the extension is used to lower the spare tire.

4. Turn the wheel wrench

counterclockwise to lower the spare tire to the ground. Continue to turn the wheel wrench until the spare tire can be pulled out from under the vehicle.

6. Tilt the tire toward the vehicle

with some slack in the cable to access the tire/wheel retainer. Tilt the retainer and pull it through the center of the wheel along with the cable and spring.

7. Put the spare tire near the

flat tire.

Removing the Flat Tire and Installing the Spare Tire Use the following pictures and instructions to remove the flat tire and raise the vehicle.

1. Jack 2. Wheel Blocks 3. Jack Handle 4. Jack Handle Extension 5. Wheel Wrench The tools you will be using include the jack (1), the wheel blocks (2), the jack handle (3), the jack handle extensions (4), and the wheel wrench (5).

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (81,1)

1. Do a safety check before

proceeding. See If a Tire Goes Flat on page 10-76 for more information.

If the vehicle has a center cap with wheel nut caps, the wheel nut caps are designed to stay with the center cap after they are loosened. Remove the entire center cap.

Vehicle Care

10-81

If the wheel has a smooth center cap, place the chisel end of the wheel wrench in the slot on the wheel, and gently pry it out.

2.

If the vehicle has wheel nut caps, loosen them by turning the wheel wrench counterclockwise.

3. Use the wheel wrench and turn it

counterclockwise to loosen the wheel nuts. Do not remove the wheel nuts yet.

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (82,1)

10-82

Vehicle Care

Front Position – 1500 Models

Front Position – All Other Models

Rear Position – 1500 Models

4. Position the jack under the

vehicle, as shown. If the flat tire is on the front of the vehicle (1500 models), position the jack under the bracket attached to the vehicle's frame, behind the flat tire.

Position the jack under the vehicle, as shown. If the flat tire is on the front of the vehicle (all other models), position the jack on the frame behind the flat tire.

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (83,1)

If a snow plow has been added to the front of the vehicle, lower the snow plow fully before raising the vehicle. Make sure that the jack head is positioned so that the rear axle is resting securely between the grooves that are on the jack head.

{ Warning

Getting under a vehicle when it is lifted on a jack is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack.

Vehicle Care

10-83

{ Warning

Raising the vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle.

6. Turn the wheel wrench

clockwise to raise the vehicle. Raise the vehicle far enough off the ground so there is enough room for the spare tire to fit under the wheel well.

5.

If the flat tire is on the rear, for 1500 models position the jack under the rear axle about 5 cm (2 in) inboard of the shock absorber bracket.

Rear Position – All Other Models For all other models, position the jack under the rear axle between the spring anchor and the shock absorber bracket.

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (84,1)

10-84

Vehicle Care

Warning (Continued)

towel can be used; however, use a scraper or wire brush later to remove all rust or dirt.

7. Remove all the wheel nuts and

take off the flat tire.

{ Warning

Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, a cloth or a paper (Continued)

8. Remove any rust or dirt from the wheel bolts, mounting surfaces, and spare wheel. Install the spare tire.

9.

{ Warning

Never use oil or grease on bolts or nuts because the nuts might come loose. The vehicle's wheel could fall off, causing a crash.

10. Put the wheel nuts back on with the rounded end of the nuts toward the wheel.

11. Tighten each wheel nut by hand. Then use the wheel wrench to tighten the nuts until the wheel is held against the hub.

12. Turn the wheel wrench

counterclockwise to lower the vehicle. Lower the jack completely.

{ Warning

If wheel studs are damaged, they can break. If all the studs on a wheel broke, the wheel could

(Continued)

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (85,1)

Warning (Continued)

come off and cause a crash. If any stud is damaged because of a loose-running wheel, it could be that all of the studs are damaged. To be sure, replace all studs on the wheel. If the stud holes in a wheel have become larger, the wheel could collapse in operation. Replace any wheel if its stud holes have become larger or distorted in any way. Inspect hubs and hub‐piloted wheels for damage. Because of loose running wheels, piloting pad damage may occur and require replacement of the entire hub, for proper centering of the wheels. When replacing studs, hubs, wheel nuts or wheels, be sure to use GM original equipment parts.

{ Warning

Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing. Follow the torque specification supplied by the aftermarket manufacturer when using accessory locking wheel nuts. See Capacities and Specifications on page 12-2 for original equipment wheel nut torque specifications.

{ Caution

Improperly tightened wheel nuts can lead to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper

(Continued)

Vehicle Care

10-85

Caution (Continued)

sequence and to the proper torque specification. See Capacities and Specifications for the wheel nut torque specification.

13. Tighten the nuts firmly in a

crisscross sequence, as shown, by turning the wheel wrench clockwise.

For vehicles with dual wheels, have a technician check the wheel nut tightness of all wheels with a torque wrench after the first 160, 1 600 and 10 000 km (100, 1,000 and 6,000 mi). Repeat this service whenever you

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (86,1)

10-86

Vehicle Care

have a tire removed or serviced. See Capacities and Specifications on page 12-2. When reinstalling the regular wheel and tire, also reinstall either the center cap, or bolt-on hub cap, depending on what the vehicle is equipped with. For center caps, place the cap on the wheel and tap it into place until it seats flush with the wheel. The cap only goes on one way. Be sure to line up the tab on the center cap with the indentation on the wheel. For bolt-on hub caps, align the plastic nut caps with the wheel nuts and then tighten by hand. Then use the wheel wrench to tighten.

Storing a Flat or Spare Tire and Tools

Store the tire under the rear of the vehicle in the spare tire carrier.

{ Warning

Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.

{ Caution

Storing an aluminum wheel with a flat tire under your vehicle for an extended period of time or with the valve stem pointing up can damage the wheel. Always stow the wheel with the valve stem pointing down and have the wheel/tire repaired as soon as possible.

1. Spare Tire (Valve Stem

Pointed Down)

2. Tire/Wheel Retainer 3. Hoist Cable 4. Hoist Assembly 5. Hoist Shaft 6. Jack Handle Extensions 7. Wheel Wrench 8. Spare Tire Lock (If Equipped) 9. Hoist Shaft Access Hole

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (87,1)

Vehicle Care

10-87

10. Hoist End of Extension Tool 1. Put the tire on the ground at the rear of the vehicle with the valve stem pointed down, and to the rear.

2. Pull the cable and spring

through the center of the wheel. Tilt the wheel retainer plate down and through the center wheel. Make sure the retainer is fully seated across the underside of the wheel.

3. Attach the wheel wrench (7) and

extensions (6) together, as shown.

4.

Insert the hoist end (10) through the hole (9) in the rear bumper and onto the hoist shaft. Do not use the chiseled end of the wheel wrench.

5. Raise the tire part way upward. Make sure the retainer is seated in the wheel opening.

6. Raise the tire fully against the

underside of the vehicle by turning the wheel wrench clockwise until you hear two clicks or feel it skip twice. You cannot overtighten the cable.

7. Make sure the tire is stored

securely. Push, pull, and then try to turn the tire. If the tire moves, use the wheel wrench to tighten the cable.

8. Reinstall the spare tire lock,

if the vehicle has one.

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (88,1)

10-88

Vehicle Care

To store the jack and jack tools:

1. Put the tools (4) in the tool

bag (5) and place them in the retaining bracket (3).

2. Tighten down the wing nut (3). 3. Assemble the wheel blocks (2)

and jack (7) together with the wing nut (1) and retaining bolt (8).

4. Position the jack (7) in the

mounting bracket (6). Position the holes in the base of the jack (7) onto the pin in the mounting bracket (6).

5. Return them to their original location in the vehicle. See “Removing the Spare Tire and Tools.”

Full-Size Spare Tire If this vehicle came with a full-size spare tire, it was fully inflated when new, however, it can lose air over time. Check the inflation pressure regularly. See Tire Pressure on page 10-61 and Vehicle Load Limits on page 9-15. For instructions on

1. Wing Nut Retaining Wheel

Blocks

2. Wheel Blocks 3. Wing Nut Retaining Tool Kit 4. Wheel Wrench and Extensions 5. Tool Bag 6. Jack Mounting Bracket 7. Jack 8. Bolt Retaining Wheel Blocks

how to remove, install, or store a spare tire, see Tire Changing on page 10-78. If equipped with a temporary use full-size spare tire, it is indicated on the tire sidewall. See Tire Sidewall Labeling on page 10-54. This spare tire should not be driven on over 112 km/h (70 mph), or 88 km/h (55 mph) when pulling a trailer, at the proper inflation pressure. Repair and replace the road tire as soon as it is convenient, and stow the spare tire for future use.

{ Caution

If the vehicle has four-wheel drive and a different size spare tire is installed, do not drive in four-wheel drive until the flat tire is repaired and/or replaced. The vehicle could be damaged and the repairs would not be covered by the warranty. Never use

(Continued)

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (89,1)

Caution (Continued)

four-wheel drive when a different size spare tire is installed on the vehicle.

The vehicle may have a different size spare tire than the road tires originally installed on the vehicle. This spare tire was developed for use on this vehicle, so it is all right to drive on it. If the vehicle has four-wheel drive and a different size spare tire is installed, drive only in two-wheel drive. After installing the spare tire on the vehicle, stop as soon as possible and check that the spare tire is correctly inflated.

Vehicle Care

10-89

Have the damaged or flat road tire repaired or replaced and installed back onto the vehicle as soon as possible so the spare tire will be available in case it is needed again. Do not mix tires and wheels of different sizes, because they will not fit. Keep your spare tire and its wheel together. If the vehicle has a spare tire that does not match the original road tires and wheels in size and type, do not include the spare in the tire rotation.

Jump Starting For more information about the vehicle battery, see Battery on page 10-31. If the vehicle's battery (or batteries) has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely.

{ Warning

Batteries can hurt you. They can be dangerous because:

. They contain acid that can

burn you.

. They contain gas that can

explode or ignite.

. They contain enough electricity to burn you.

If you do not follow these steps exactly, some or all of these things can hurt you.

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (90,1)

10-90

Vehicle Care

{ Caution

Ignoring these steps could result in costly damage to the vehicle that would not be covered by the vehicle warranty. Trying to start the vehicle by pushing or pulling it will not work, and it could damage the vehicle.

1. Check the other vehicle. It must

have a 12-volt battery with a negative ground system.

{ Caution

If the other vehicle does not have a 12-volt system with a negative ground, both vehicles can be damaged. Only use a vehicle that has a 12-volt system with a negative ground for jump starting.

2.

If you have a vehicle with a diesel engine with two batteries, you should know before you

begin that, especially in cold weather, you may not be able to get enough power from a single battery in another vehicle to start your diesel engine. If your vehicle has more than one battery, using the battery that is closer to the starter will reduce electrical resistance. This is located on the passenger side, in the rear of the engine compartment.

3. Get the vehicles close enough

so the jumper cables can reach, but be sure the vehicles are not touching each other. If they are, it could cause an unwanted ground connection. You would not be able to start your vehicle, and the bad grounding could damage the electrical systems. To avoid the possibility of the vehicles rolling, set the parking brake firmly on both vehicles involved in the jump start procedure. Put the automatic transmission in P (Park) or a manual transmission in Neutral

before setting the parking brake. If you have a four-wheel-drive vehicle, be sure the transfer case is in a drive gear, not in N (Neutral).

{ Caution

If any accessories are left on or plugged in during the jump starting procedure, they could be damaged. The repairs would not be covered by the vehicle warranty. Whenever possible, turn off or unplug all accessories on either vehicle when jump starting.

4. Turn off the ignition on both

vehicles. Unplug unnecessary accessories plugged into the accessory power outlets. Turn off the radio and all the lamps that are not needed. This will avoid sparks and help save both batteries. And it could save the radio!

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (91,1)

5. Open the hood on the other

vehicle and locate the positive (+) and negative (−) terminal locations on that vehicle. The positive (+) terminal is under a red plastic cover at the positive battery post. To uncover the positive (+) terminal, open the red plastic cover. For more information on the location of the remote positive (+) and remote negative (−) terminals, see Engine Compartment Overview on page 10-5.

{ Warning

An electric fan can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan.

Vehicle Care

10-91

{ Warning

{ Warning

Using an open flame near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a flashlight if you need more light. Be sure the battery has enough water. You do not need to add water to the battery installed in your new vehicle. But if a battery has filler caps, be sure the right amount of fluid is there. If it is low, add water to take care of that first. If you do not, explosive gas could be present. Battery fluid contains acid that can burn you. Do not get it on you. If you accidentally get it in your eyes or on your skin, flush the place with water and get medical help immediately.

Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running.

6. Check that the jumper cables do

not have loose or missing insulation. If they do, you could get a shock. The vehicles could be damaged too. Before you connect the cables, here are some basic things you should know. Positive (+) will go to positive (+) or to a remote positive (+) terminal if the vehicle has one. Negative (−) will go to a heavy, unpainted metal engine part or to a remote negative (−) terminal if the vehicle has one. Do not connect positive (+) to negative (−) or you will get a short that would damage the battery and maybe other parts

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (92,1)

10-92

Vehicle Care

too. And do not connect the negative (−) cable to the negative (−) terminal on the dead battery because this can cause sparks.

5.3L Shown, 4.3L, 6.0L, 6.2L and

6.6L Similar

7. Connect the red positive (+)

cable to the positive (+) terminal of the vehicle with the dead battery.

8. Do not let the other end touch

metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one.

9. Connect the black negative (−)

cable to the negative (−) terminal of the good battery. Use a remote negative (−) terminal if the vehicle has one. Do not let the other end touch anything until the next step.

10. Connect the other end of the

negative (−) cable.

4.3L Shown, 5.3L and 6.2L Similar

‐ To the metal bracket that is

bolted to the engine and supports the resonator, on the vehicle with the dead battery.

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (93,1)

Vehicle Care

10-93

{ Caution If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by the vehicle warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.

Jumper Cable Removal Reverse the sequence exactly when removing the jumper cables.

6.0L

6.6L

‐ To the generator bracket, on

the vehicle with the dead battery.

‐ To the negative (−) post on the auxiliary battery, on the vehicle with the dead battery. 11. Start the vehicle with the good

battery and run the engine for a while.

12. Try to start the vehicle that had

the dead battery. If it will not start after a few tries, it probably needs service.

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (94,1)

10-94

Vehicle Care

Towing the Vehicle

{ Caution

Incorrectly towing a disabled vehicle may cause damage. The damage would not be covered by the vehicle warranty. Do not lash or hook to the chassis components — including the front and rear subframes, suspension control arms, and links — during towing and recovery of a disabled vehicle, or when securing the vehicle. Use the proper nylon strap harnesses around the tires to secure the vehicle.

Have the vehicle towed on a flatbed car carrier or a wheel lift tow truck. If a wheel lift tow truck is used, the drive wheels cannot contact the road while the vehicle is being towed. A wheel dolly must be used to lift all drive wheels off the ground.

Consult your dealer or a professional towing service if the disabled vehicle must be towed. To tow the vehicle behind another vehicle for recreational purposes, such as behind a motor home, see “Recreational Vehicle Towing” following.

Recreational Vehicle Towing Recreational vehicle towing means towing the vehicle behind another vehicle, such as a motor home. The two most common types of recreational vehicle towing are known as dinghy towing and dolly towing. Dinghy towing is towing the vehicle with all four wheels on the ground. Dolly towing is towing the vehicle with two wheels on the ground and two wheels up on a device known as a dolly.

Here are some important things to consider before recreational vehicle towing: . What is the towing capacity of the towing vehicle? Be sure to read the tow vehicle manufacturer's recommendations.

. What is the distance that will be

traveled? Some vehicles have restrictions on how far and how long they can tow. Is the proper towing equipment going to be used? See your dealer or trailering professional for additional advice and equipment recommendations. Is the vehicle ready to be towed? Just as preparing the vehicle for a long trip, make sure the vehicle is prepared to be towed.

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (95,1)

Dinghy Towing

Two-Wheel-Drive Vehicles

Two-wheel-drive vehicles should not be towed with all four wheels on the ground. Two-wheel-drive transmissions have no provisions for internal lubrication while being towed.

Four-Wheel-Drive Vehicles See your dealer for the procedure to tow this vehicle.

Vehicle Care

10-95

Dolly Towing

Front Towing (Front Wheels Off the Ground) – Two-Wheel-Drive Vehicles

{ Caution

If the vehicle is towed with all four wheels on the ground, the drivetrain components could be damaged. The repairs would not be covered by the vehicle warranty. Do not tow the vehicle with all four wheels on the ground.

{ Caution

If a two-wheel-drive vehicle is towed with the rear wheels on the ground, the transmission could be damaged. The repairs would not be covered by the vehicle

(Continued)

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (96,1)

10-96

Vehicle Care

Caution (Continued)

warranty. Never tow the vehicle with the rear wheels on the ground.

Two-wheel-drive vehicles should not be towed with the rear wheels on the ground. Two-wheel-drive transmissions have no provisions for internal lubrication while being towed. To dolly tow a two-wheel-drive vehicle, the vehicle must be towed with the rear wheels on the dolly. See “Rear Towing (Rear Wheels Off the Ground)” later in this section for more information.

Front Towing (Front Wheels Off the Ground) – Four-Wheel-Drive Vehicles See your dealer for the procedure to tow this vehicle.

Rear Towing (Rear Wheels Off the Ground)

Two-Wheel-Drive Vehicles

Use the following procedure to dolly tow a two-wheel-drive vehicle from the rear: 1. Attach the dolly to the tow vehicle following the dolly manufacturer's instructions.

2. Drive the rear wheels onto the

dolly.

3. Firmly set the parking brake.

See Parking Brake on page 9-54.

4. Put the transmission in P (Park). 5. Secure the vehicle to the dolly

following the manufacturer's instructions.

6. Use an adequate clamping

device designed for towing to ensure that the front wheels are locked into the straight position. 7. Turn the ignition to LOCK/OFF.

Four-Wheel-Drive Vehicles See your dealer for the procedure to tow this vehicle.

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (97,1)

Appearance Care

Exterior Care

Locks Locks are lubricated at the factory. Use a de-icing agent only when absolutely necessary, and have the locks greased after using. See Recommended Fluids and Lubricants on page 11-12. Washing the Vehicle To preserve the vehicle's finish, wash it often and out of direct sunlight.

{ Caution

Do not use petroleum-based, acidic, or abrasive cleaning agents as they can damage the vehicle's paint, metal, or plastic parts. If damage occurs, it would not be covered by the vehicle warranty. Approved cleaning

(Continued)

Caution (Continued)

products can be obtained from your dealer. Follow all manufacturer directions regarding correct product usage, necessary safety precautions, and appropriate disposal of any vehicle care product.

{ Caution Avoid using high-pressure washes closer than 30 cm (12 in) to the surface of the vehicle. Use of power washers exceeding 8,274 kPa (1,200 psi) can result in damage or removal of paint and decals.

This symbol e is on any underhood compartment electrical center that should not be power

Vehicle Care

10-97

washed. This could cause damage that would not be covered by the vehicle warranty. If using an automatic car wash, follow with the car wash instructions. The windshield wiper and rear window wiper, if equipped, must be off. Remove any accessories that may be damaged or interfere with the car wash equipment. Rinse the vehicle well, before washing and after, to remove all cleaning agents completely. If they are allowed to dry on the surface, they could stain. Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting. Finish Care Application of aftermarket clearcoat sealant/wax materials is not recommended. If painted surfaces are damaged, see your dealer to have the damage assessed and

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (98,1)

10-98

Vehicle Care

repaired. Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage the vehicle's finish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter. Occasional hand waxing or mild polishing should be done to remove residue from the paint finish. See your dealer for approved cleaning products. Do not apply waxes or polishes to uncoated plastic, vinyl, rubber, decals, simulated wood, or flat paint as damage can occur.

{ Caution Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/ clearcoat paint finish on the vehicle.

To keep the paint finish looking new, keep the vehicle garaged or covered whenever possible.

Protecting Exterior Bright Metal Moldings

{ Caution

Failure to clean and protect the bright metal moldings can result in a hazy white finish or pitting. This damage would not be covered by the vehicle warranty.

The bright metal moldings on the vehicle are aluminum. To prevent damage always follow these cleaning instructions: . Be sure the molding is cool to the touch before applying any cleaning solution.

. Use a cleaning solution

approved for aluminum. Some cleaners are highly acidic or contain alkaline substances and can damage the moldings.

. Always dilute a concentrated

cleaner according to the manufacturer’s instructions. . Do not use chrome cleaners. . Do not use cleaners that are not

intended for automotive use.

. Use a nonabrasive wax on the vehicle after washing to protect and extend the molding finish.

Spray-In Bedliner Care A spray-in bedliner is a permanent coating that bonds to the truck bed and cannot be removed. Promptly

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 5853506) - 2014 - CRC 3rd Edition - 8/29/13

Black plate (99,1)

rinse the bedliner surface following a chemical spill to avoid permanent damage. Spray-in bedliners can fade from oxidation, road dirt, heavy-duty hauling, and hard water stains. Clean it periodically by washing off the loose dirt and using a mild detergent. To restore the original appearance, apply the bedliner conditioner available through your dealer.

{ Caution

Using silicone-based products may damage the bedliner, reduce the slip-resistant texture, and attract dirt.

Cleaning Exterior Lamps/ Lenses, Emblems, Decals and Stripes Use only lukewarm or cold water, a soft cloth, and a car washing soap to clean exterior lamps, lenses,

emblems, decals and stripes. Follow instructions under "Washing the Vehicle" previously in this section. Lamp covers are made of plastic, and some have a UV protective coating. Use only lukewarm water, a soft cloth, and mild car washing soap to clean exterior lamps and lenses. Do not clean or wipe them while they are dry. Do not use any of the following on lamp covers: . Abrasive or caustic agents. . Washer fluids and other cleaning

agents in higher concentrations than suggested by the manufacturer.

. Solvents, alcohols, fuels, or other harsh cleaners. Ice scrapers or other hard items. . Aftermarket appearance caps or

covers while the lamps are illuminated, due to excessive heat generated.

Vehicle Care

10-99