2007 Chevrolet Cobalt Owners Manual

Download PDF Manual
enter narrow areas. Outside Remote Control Mirror Adjust the driver’s outside mirror with the control lever located on the driver’s door. Adjust the outside mirrors so that the side of the vehicle can be seen while sitting in a comfortable driving position. To adjust the passenger’s outside mirror, sit in the driver’s seat and have a passenger adjust the mirror for you. The mirror is a manual fold design. 127 Outside Power Mirrors The controls for the outside power mirrors are located on the driver’s door armrest. Move the selector switch located below the four-way control pad to the left or right to choose either the driver’s side or passenger’s side mirror. To adjust a mirror, use the arrows located on the four-way control pad to move the mirror in the desired direction. The mirror will only move right or left, up or down. Adjust each outside mirror so that a little of the vehicle and the area behind it can be seen while sitting in a comfortable driving position. Keep the selector switch in the center position when not adjusting either outside mirror. 128 Both mirrors can manually be folded by pulling them toward the vehicle. This feature may be useful when going through a car wash or a conﬁned space. Push the mirrors away from the vehicle, to the normal position, before driving. Outside Convex Mirror {CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes. The passenger’s side mirror is convex. A convex mirror’s surface is curved so more can be seen from the driver’s seat. It also makes things appear farther away than they really are. OnStar® System OnStar® uses several innovative technologies and live advisors to provide you with a wide range of safety, security, information, and convenience services. If your airbags deploy, the system is designed to make an automatic call to OnStar® Emergency advisors who can request emergency services be sent to your location. If you lock your keys in the vehicle, call OnStar® at 1-888-4-ONSTAR and they can send a signal to unlock your doors. If you need roadside assistance, press the OnStar® button and they can contact Roadside Service for you. OnStar® service is provided to you subject to the OnStar® Terms and Conditions. You may cancel your OnStar® service at any time by contacting OnStar® as provided below. A complete OnStar® Owner’s Guide and the OnStar® Terms and Conditions are included in the vehicle’s OnStar® Subscriber glove box literature. For more information, visit onstar.com or onstar.ca, contact OnStar® at 1–888–4–ONSTAR (1–888–466–7827) or TTY 1–877–248–2080, or press the OnStar® button to speak with an OnStar® advisor 24 hours a day, 7 days a week. Not all OnStar® features are available on all vehicles. To check if your vehicle is equipped to provide the services described below, or for a full description of OnStar® services and system limitations, see the OnStar® Owner’s Guide in your glove box or visit onstar.com. 129 OnStar® Services For new vehicles equipped with OnStar®, the Safe & Sound Plan, or the Directions & Connections® Plan is included for one year from the date of purchase. You can extend this plan beyond the ﬁrst year, or upgrade to the Directions & Connections® Plan. For more information, press the OnStar® button to speak with an advisor. Some OnStar® services (such as Remote Door Unlock or Stolen Vehicle Location Assistance) may not be available until you register with OnStar®. Available Services with Safe & Sound® Plan (cid:127) Automatic Notiﬁcation of Airbag Deployment (cid:127) Advanced Automatic Crash Notiﬁcation (AACN) (If equipped) (cid:127) Link to Emergency Services (cid:127) Roadside Assistance (cid:127) Stolen Vehicle Location Assistance (cid:127) AccidentAssist (cid:127) Remote Door Unlock/Vehicle Alert (cid:127) OnStar® Vehicle Diagnostics (cid:127) GM® Goodwrench® On Demand Diagnostics (cid:127) OnStar® Hands-Free Calling with 30 complimentary minutes (cid:127) OnStar® Virtual Advisor Available Services included with Directions & Connections® Plan (cid:127) All Safe and Sound Plan Services (cid:127) Driving Directions - Advisor delivered or OnStar® Turn-by-Turn Navigation (If equipped) (cid:127) RideAssist (cid:127) Information and Convenience Services 130 OnStar® Steering Wheel Controls Your vehicle may have a Talk/Mute button that can be used to interact with OnStar® Hands-Free Calling. See Audio Steering Wheel Controls on page 217 for more information. On some vehicles, you may have to hold the button for a few seconds and give the command “ONSTAR” in order to activate the OnStar® Hands-Free Calling feature. On some vehicles, the mute button can be used to dial numbers into voicemail systems, or to dial phone extensions. See the OnStar® Owner’s Guide for more information. OnStar® Hands-Free Calling OnStar® Hands-Free Calling allows eligible OnStar® subscribers to make and receive calls using voice commands. Hands-Free Calling is fully integrated into the vehicle, and can be used with OnStar® Pre-Paid Minute Packages. Hands-Free Calling may also be linked to a Verizon Wireless service plan, depending on eligibility. To ﬁnd out more, refer to the OnStar® Owner’s Guide in the vehicle’s glove box, visit www.onstar.com or www.onstar.ca, or speak with an OnStar® advisor by pressing the OnStar® button or calling 1-888-4-ONSTAR (1-888-466-7827). OnStar® Virtual Advisor OnStar® Virtual Advisor is a feature of OnStar® Hands-Free Calling that uses your minutes to access location-based weather, local traffic reports, and stock quotes. By pressing the phone button and giving a few simple voice commands, you can browse through the various topics. See the OnStar® Owner’s Guide for more information. 131 How OnStar® Service Works In order to provide you with OnStar® services, your vehicle’s OnStar® system has the capability of recording and transmitting vehicle information. This information is automatically sent to an OnStar® Call Center at the time of an OnStar® button press, Emergency button press or if your airbags or AACN system deploys. The vehicle information usually includes your GPS location and, in the event of a crash, additional information regarding the accident that your vehicle has been involved in (e.g. the direction from which your vehicle was hit). When you use the Virtual Advisor feature of OnStar® Hands-Free Calling, your vehicle also sends OnStar® your GPS location so that we can provide you with location-based services. OnStar® service cannot work unless your vehicle is in a place where OnStar® has an agreement with a wireless service provider for service in that area. OnStar® service also cannot work unless you are in a place where the wireless service provider OnStar® has hired for that area has coverage, network capacity and reception when the service is needed, and technology that is compatible with the OnStar® service. Not all services are available everywhere, particularly in remote or enclosed areas, or at all times. OnStar® service that involves location information about your vehicle cannot work unless GPS satellite signals are unobstructed and available in that place as well. Your vehicle must have a working electrical system (including adequate battery power) for the OnStar® equipment to operate. There are other problems OnStar® cannot control that may prevent OnStar® from providing OnStar® service to you at any particular time or place. Some examples are damage to important parts of your vehicle in an accident, hills, tall buildings, tunnels, weather or wireless phone network congestion. 132 Your Responsibility You may need to increase the volume of your radio to hear the OnStar® advisor. If the light next to the OnStar® buttons is red, this means that your system is not functioning properly and should be checked by a dealer. If the light appears clear (no light is appearing), your OnStar® subscription has expired. You can always press the blue OnStar® button to conﬁrm that your OnStar® equipment is active. Storage Areas Glove Box Open the glove box by lifting up on the lever. Close the glove box with a ﬁrm push. Cupholder(s) There are two cupholders located at the front of the center console, in front of the shift lever. These cupholders have a black rubber liner that can be removed for cleaning or to accommodate larger cup sizes. There are also cupholders for the rear seat passengers located at the rear of the center console. Center Console Storage Area Your vehicle may have a center console armrest with storage area. Use the lever on the front of the console to open it. Driver’s Storage Compartment The driver’s storage compartment is located near the left side of the steering column on the bottom of the instrument panel. Pull the cover down to open. It can be used to store small items. 133 Convenience Net Your vehicle may have a convenience net. You will see it inside the back wall of the trunk. Put small loads behind the net. It can help keep them from falling over during sharp turns or quick starts and stops. Unclip a corner of the convenience net to ﬁt larger objects behind the net, then reclip it to secure them in place. The net is not for larger, heavier loads. Store them in the trunk as far forward as you can. You can unhook the net so that it will lie ﬂat when you are not using it. Sunroof If the vehicle has a sunroof, the switch that operates it is located on the headliner between the map lamps. The sunroof will only operate while the ignition is on, or turned to ACC, or if Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 111. Press the sunroof switch rearward to open the sunroof to the vent position. If the sunshade is closed, it must be opened manually in the vent position. Press and hold the switch rearward a second time to open the sunroof. If the sunshade is closed, it will open automatically when the sunroof is opened. To close the sunroof, press the switch forward and hold it until the sunroof is closed. The sunroof will stop if the switch is released. Close the sunshade by hand. The sunroof glass panel cannot be opened or closed if the vehicle has an electrical failure. Notice: the sliding glass panel, damage will occur and the sunroof may not open or close properly. Always close the glass panel before closing the sunshade. If you force the sunshade forward of 134 Section 3 Instrument Panel Instrument Panel Overview ........................ 138 Hazard Warning Flashers .......................... 140 Other Warning Devices ............................. 140 Horn .......................................................... 140 Tilt Wheel .................................................. 140 Turn Signal/Multifunction Lever .................. 141 Turn and Lane-Change Signals ................. 142 Headlamp High/Low-Beam Changer .......... 142 Flash-to-Pass ............................................ 143 Windshield Wipers ..................................... 143 Windshield Washer .................................... 144 Cruise Control ........................................... 145 Headlamps ................................................ 148 Wiper Activated Headlamps ....................... 149 Headlamps on Reminder ........................... 149 Daytime Running Lamps (DRL) ................. 149 Fog Lamps ................................................ 150 Instrument Panel Brightness ...................... 150 Dome Lamp .............................................. 151 Entry/Exit Lighting ...................................... 151 Mirror Reading Lamps ............................... 151 Electric Power Management ...................... 151 Battery Run-Down Protection ..................... 152 Accessory Power Outlet(s) ........................ 152 Ashtray(s) and Cigarette Lighter ................ 153 Climate Controls ......................................... 154 Climate Control System ............................. 154 Outlet Adjustment ...................................... 157 Passenger Compartment Air Filter ............. 158 Warning Lights, Gages, and Indicators ..... 160 Instrument Panel Cluster ........................... 161 Speedometer and Odometer ...................... 162 Tachometer ............................................... 162 Safety Belt Reminder Light ........................ 162 Passenger Safety Belt Reminder Light ....... 163 Airbag Readiness Light ............................. 163 Passenger Airbag Status Indicator ............. 164 Charging System Light .............................. 166 Up-Shift Light ............................................ 167 Brake System Warning Light ..................... 167 Anti-Lock Brake System Warning Light ...... 168 Enhanced Traction System Warning Light ...................................................... 169 135 Section 3 Instrument Panel Engine Coolant Temperature Warning Light ...................................................... 170 Malfunction Indicator Lamp ........................ 170 Oil Pressure Light ..................................... 174 Security Light ............................................ 175 Fog Lamp Light ......................................... 175 Highbeam On Light ................................... 175 Fuel Gage ................................................. 175 Boost Gage ............................................... 176 Driver Information Center (DIC) .................. 177 DIC Operation and Displays ...................... 178 DIC Warnings and Messages .................... 180 DIC Vehicle Personalization ....................... 182 Audio System(s) ......................................... 188 Setting the Time (Without Date Display) .... 189 Setting the Time (With Date Display) ......... 190 Radio with CD (Base) ............................... 192 Radio with CD (MP3) ................................ 197 Using an MP3 ........................................... 207 XM Radio Messages ................................. 215 Theft-Deterrent Feature ............................. 217 Audio Steering Wheel Controls .................. 217 Radio Reception ........................................ 218 Care of Your CDs ..................................... 219 Care of the CD Player .............................. 219 Fixed Mast Antenna .................................. 219 XM™ Satellite Radio Antenna System ....... 219 136 ✍ NOTES 137 Instrument Panel Overview 138 The main components of your instrument panel are the following: A. Side Window Outlets. See Climate Control System on page 154. B. Air Outlets. See Outlet Adjustment on page 157. C. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 141. D. Cruise Control Buttons (If Equipped) and Driver Information Control Buttons. See Cruise Control on page 145 and Driver Information Center (DIC) on page 177. E. Instrument Panel Cluster. See Instrument Panel Cluster on page 161 F. Audio Steering Wheel Controls (If Equipped). See Audio Steering Wheel Controls on page 217. G. Hazard Warning Flashers Button. See Hazard Warning Flashers on page 140. H. Windshield Wiper/Washer Controls. See Windshield Wipers on page 143 and Windshield Washer on page 144. I. Audio System. See Audio System(s) on page 188. J. Fog Lamp Button (If Equipped). See Fog Lamps on page 150. K. Trunk Release. See Trunk on page 100. L. Instrument Panel Brightness Control. See Instrument Panel Brightness on page 150. M. Horn. See Horn on page 140. N. Cigarette Lighter (If Equipped). See Ashtray(s) and Cigarette Lighter on page 153. O. Shift Lever (Manual Shown). See Manual Transaxle Operation on page 118 and Automatic Transaxle Operation on page 115. P. Climate Controls. See Climate Control System on page 154. Q. Passenger Air Bag Status Indicator and Heated Seats Button (If Equipped). See Passenger Airbag Status Indicator on page 164 and Heated Seats on page 11. R. Glove Box. See Glove Box on page 133. 139 Other Warning Devices If you carry reﬂective triangles, you can set them up at the side of the road about 300 feet (100 m) behind your vehicle. Horn To sound the horn, press the center pad on the steering wheel. Tilt Wheel A tilt wheel allows you to adjust the steering wheel before you drive. You can raise the steering wheel to the highest level to give your legs more room when you enter and exit the vehicle. Hazard Warning Flashers Your hazard warning ﬂashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will ﬂash on and off. The hazard warning ﬂasher button is located in the center of the instrument panel. Your hazard warning ﬂashers work no matter what position your key is in, and even if the key is not in the ignition switch. Press the button to make the front and rear turn signal lamps ﬂash on and off. Press the button again to turn the ﬂashers off. When the hazard warning ﬂashers are on, your turn signals will not work. 140 The lever that allows you to tilt the steering wheel is located on the left side of the steering column. Turn Signal/Multifunction Lever To tilt the wheel, pull down the lever. Then move the wheel to a comfortable position, pull up the lever to lock the wheel in place. The lever on the left side of the steering column includes the following: (cid:127) G Turn and Lane-Change Signals. See Turn and Lane-Change Signals on page 142. (cid:127) 23 Headlamp High/Low-Beam Changer. See Headlamp High/Low-Beam Changer on page 142. (cid:127) Flash-to-Pass. See Flash-to-Pass on (cid:127) O Exterior Lamp Control. See Headlamps on page 143. page 148. 141 Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is ﬁnished, the lever will return automatically. An arrow on the instrument panel cluster will ﬂash in the direction of the turn or lane change. To signal a lane change, raise or lower the lever until the arrow starts to ﬂash. Hold it there until you complete your lane change. The lever will return by itself when you release it. As you signal a turn or a lane change, if the arrows ﬂash rapidly, a signal bulb may be burned out and other drivers will not see your turn signal. If a bulb is burned out, replace it to help avoid an accident. If the arrows do not go on at all when you signal a turn, check the fuse. See Fuses and Circuit Breakers on page 379. Headlamp High/Low-Beam Changer To change the headlamps from low beam to high beam, push the turn signal lever away from you. When the high beams are on, this light on the instrument panel cluster will also be on. To change the headlamps from high beam to low beam, pull the turn signal lever toward you. 142 Flash-to-Pass This feature lets you use your high-beam headlamps to signal a driver in front of you that you want to pass. To use it, pull the turn signal/multifunction lever toward you until the high-beam headlamps come on, then release the lever to turn them off. Windshield Wipers Use this lever, located on the right side of the steering wheel, to operate the windshield wipers. 9(Off): Move the lever to this position to turn off the windshield wipers. &(Intermittent; Speed Sensitive Wipers): Move the lever to this position for intermittent or speed sensitive operation. When you select this position, the delay will vary depending on the vehicles speed, as well as, the manually selected delay. x(Delay): When the lever is in the intermittent position, turn the intermittent adjust band with this symbol on it up or down to set for a shorter or longer delay between wipes. To the left of the adjust band are bars, increasing in size from bottom to top, that indicate the frequency of the wipes. Smaller bars mean the wipers movement is less frequent. Larger bars mean the movement is more frequent. 6 (Low Speed): Move the lever up to the ﬁrst setting past intermittent, for steady wiping at low speed. 1 (High Speed): Move the lever up to the second setting past intermittent, for wiping at high speed. 8(Mist): Move the lever all the way down to this position for a single wiping cycle. Hold it there until the windshield wipers start; then let go. 143 The windshield wipers will stop after one wiping cycle. If you want additional wiping cycles, hold the lever down longer. Damaged wiper blades may prevent you from seeing well enough to drive safely. To avoid damage, be sure to clear ice and snow from the wiper blades before using them. If the wiper blades are frozen to the windshield, carefully loosen or thaw them. If your blades do become damaged, get new blades. Heavy snow or ice can overload your wiper motor. A circuit breaker will stop the motor until it cools. Clear away snow or ice to prevent an overload. If the motor gets stuck, turn the wipers off, clear away the snow or ice, and then turn the wipers back on. As an added safety feature, if the wipers are on for more than 15 seconds, the vehicle’s headlamps will turn on automatically. They will turn off 15 seconds after the wipers are turned off. Windshield Washer To wash your windshield, press the button at the end of the lever until the washers begin. {CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. When you release the button, the washers will stop, but the wipers will continue to wipe for about three times or will resume the speed you were using before. 144 Cruise Control With cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below 25 mph (40 km/h). {CAUTION: Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use your cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control. Do not use cruise control on slippery roads. Setting Cruise Control {CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control. The cruise control buttons are located on the left side of the steering wheel. J(On/Off): Press this button to turn the cruise control system on and off. 145 RES+ (Resume): Press this button to resume a set speed and to accelerate the speed. SET– (Set): Press this button to set a speed and to decrease the speed. To set a speed do the following: 1. Press the on/off button to turn cruise control on. The indicator light on the button will come on. 2. Get to the speed you want. 3. Press the SET– part of the control button and release it. The CRUISE ENGAGED message will appear on the Driver Information Center (DIC) to show the system is engaged. 4. Take your foot off the accelerator pedal. If the vehicle is in cruise control and the Traction Control System (TCS) begins to limit wheel spin, the cruise control will automatically disengage. See Enhanced Traction System (ETS) on page 230. When road conditions allow, the cruise control can be used again. 146 Resuming a Set Speed Suppose you set the cruise control at a desired speed and then you apply the brake. This, of course, disengages the cruise control. To return to the previously set speed, you do not need to go through the set process again. Once you are going about 25 mph (40 km/h) or more, you can press the RES+ part of the button brieﬂy. This will take you back up to your previously chosen speed and stay there. Increasing Speed While Using Cruise Control There are two ways to go to a higher speed. 1. Disengage the cruise control by applying the brake pedal but do not turn it off. Accelerate to a higher speed and reset the cruise control. 2. If the cruise control system is already engaged, press the RES+ part of the button. Hold it there until you get up to the speed desired, and then release the button. To increase the vehicle speed in very small amounts, press the RES+ part of the button brieﬂy and then release it. Each time you do this, the vehicle will go about 1 mph (1.6 km/h) faster. Reducing Speed While Using Cruise Control If the cruise control system is already engaged, (cid:127) Push and hold the SET– part of the button until you reach the lower speed you want, then release it. (cid:127) To slow down in very small amounts, push the SET– part of the button brieﬂy. Each time you do this, the vehicle will go about 1 mph (1.6 km/h) slower. Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase your speed. When you take your foot off the pedal, the vehicle will slow down to the cruise control speed you set earlier. Using Cruise Control on Hills How well the cruise control will work on hills depends upon the vehicle speed, load and the steepness of the hills. When going up steep hills, you may have to step on the accelerator pedal to maintain the vehicle’s speed. When going downhill, you may have to brake or shift to a lower gear to keep the vehicle’s speed down. Of course, applying the brake takes turns off the cruise control. Many drivers ﬁnd this to be too much trouble and do not use cruise control on steep hills. Ending Cruise Control To end cruise control, step lightly on the brake pedal or the clutch pedal if the vehicle has a manual transaxle. Stepping on the brake pedal or clutch pedal will only end the current cruise control session. Press the cruise control on/off button to turn the system completely off. Erasing Speed Memory When you turn off the cruise control or the ignition, the cruise control set speed memory is erased. 147 AUTO (Automatic Headlamp System): Turn the switch to this position to automatically turn on the Daytime Running Lamps (DRL) during daytime, and the headlamps, parking lamps, and taillamps at night. This position must be selected in order for the Wiper Activated Headlamps to be activated. See Wiper Activated Headlamps on page 149. P(Off/On): This position is the momentary Off/On switch for the Automatic Headlamp System. For vehicles ﬁrst sold in Canada, the transaxle must be in the PARK (P) position, before the Automatic Headlamp System can be turned off. When operating in AUTO, a momentary turn of the switch to off/on will turn off the Automatic Headlamp System. Rotating the switch to off/on again will turn the Automatic Headlamp System back on. The Automatic Headlamp System is always turned on at the beginning of an ignition cycle. Headlamps The lever on the left side of the steering column operates the exterior lamps. The exterior lamp switch has the following four positions: 2(Headlamps): Turn the switch to this position to turn on the headlamps, parking lamps, and taillamps. ;(Parking Lamps): Turn the switch to this position to turn on the parking lamps and taillamps only. 148 Wiper Activated Headlamps This feature activates the headlamps and parking lamps after the windshield wipers are turned on. For this feature to work, automatic lighting must be enabled. See Headlamps on page 148 for additional information. When the ignition is turned off, the wiper-activated headlamps will immediately turn off. They will also turn off 15 seconds after the windshield wiper control is turned off. Headlamps on Reminder If you open the driver’s door with the ignition off and the lamps on, you will hear a warning chime. Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional daytime running lamps are required on all vehicles ﬁrst sold in Canada. The vehicle has a light sensor on top of the instrument panel. Make sure it is not covered, or the head lamps will be on when not needed. The DRL system will make the headlamps come on when the following conditions are met: (cid:127) The ignition is on. (cid:127) The exterior lamps control is in AUTO or the parking lamps only position. (cid:127) The light sensor detects daytime light. (cid:127) The parking brake is released. When the DRL system is on, the taillamps, sidemarker lamps, parking lamps, and instrument panel lights will not be illuminated unless you have turned the exterior lamps control to the parking lamp position. As with any vehicle, you should turn on the regular headlamp system when you need it. 149 Fog Lamps Instrument Panel Brightness If equipped, the fog lamp button is located on the instrument panel, to the left of the steering wheel. The control for this feature is located on the instrument panel to the left of the steering wheel. Turn the knob clockwise to brighten the lights or counterclockwise to dim the instrument panel lights, when the headlamps are on. The ignition must be on to turn your fog lamps on. Push the button to turn the fog lamps on. An indicator light on the cluster will come on when the fog lamps are on. Push the button again to turn the fog lamps off. The parking lamps will automatically turn on and off when the fog lamps are turned on and off. The fog lamps will turn off while the high-beam headlamps are turned on. Some localities have laws that require the headlamps to be on along with the fog lamps. 150 Dome Lamp Your vehicle may have a dome lamp. 9(Off): Move the lever to this position to turn the lamp off, even when a door is opened. 1(Door): Move the lever to this position to turn the lamp on whenever a door is opened. +(On): Move the lever to this position to turn the dome lamp on. Entry/Exit Lighting The lamps inside your vehicle will go on when you open any door. These lamps will fade out after about 20 seconds after all of the doors have been closed or when the ignition is turned on. These lamps will also go on when you press the trunk release, unlock symbol button or the horn symbol on the keyless entry system transmitter. The lamps inside your vehicle will stay on for about 20 seconds after your key is removed from the ignition to provide an illuminated exit. Mirror Reading Lamps Your vehicle may have reading lamps on the rearview mirror. Push the button to turn the reading lamps on and off. Electric Power Management This vehicle has Electric Power Management (EPM), an advanced control system. It estimates the battery’s temperature and state of charge and then adjusts the voltage for best performance and extended life of the battery. When the battery’s state of charge is low, the voltage is raised slightly to quickly put the charge back in. When the state of charge is high, the voltage is lowered slightly to prevent overcharging. If the vehicle has a voltmeter gage or voltage display on the Driver Information Center (DIC), you may see the voltage move up or down. This is normal. If there is a problem, an alert will be displayed. 151 The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all the power that is needed for very high electrical loads. A high electrical load occurs when several of the following loads are on: headlamps, high beams, fog lamps, rear window defogger, climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets. EPM works to prevent excessive discharge of the battery. It does this by balancing the generator’s output and the vehicle’s electrical needs. It can increase engine idle speed to generate more power, whenever needed. It can temporarily reduce the power demands of some accessories. Normally, these actions occur in steps or levels, without being noticeable. In rare cases at the highest levels of corrective action, this action may be noticeable to the driver. Battery Run-Down Protection Your vehicle has a battery saver feature designed to protect your vehicle’s battery. When any interior lamp is left on and the ignition is turned off, the battery rundown protection system will automatically turn the lamp off after 20 minutes. This will avoid draining the battery. Accessory Power Outlet(s) Accessory power outlets can be used to connect electrical equipment such as a cellular phone or CB radio. The accessory power outlet is located in the center console, rearward of the shift lever. To use the outlet, remove the cover. When not in use, always cover the outlet with the protective cap. Notice: Leaving electrical equipment on for extended periods will drain the battery. Always turn off electrical equipment when not in use and do not plug in equipment that exceeds the maximum amperage rating. 152 Certain electrical accessories may not be compatible with the accessory power outlet and could result in blown vehicle or adapter fuses. If you experience a problem, see your dealer for additional information on the accessory power outlet. Notice: Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should. The repairs would not be covered by your warranty. Do not use equipment exceeding maximum amperage rating of 20 amperes. Check with your dealer before adding electrical equipment. When adding electrical equipment, be sure to follow the installation instructions included with the equipment. Notice: Improper use of the power outlet can cause damage not covered by your warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only. Ashtray(s) and Cigarette Lighter Your vehicle may have an ashtray and cigarette lighter. To use the lighter, located on the instrument panel below the climate controls, push it in all the way and let go. When it is ready, it will pop back out by itself. Notice: Holding a cigarette lighter in while it is heating will not allow the lighter to back away from the heating element when it is hot. Damage from overheating may occur to the lighter or heating element, or a fuse could be blown. Do not hold a cigarette lighter in while it is heating. Do not use equipment exceeding maximum amperage rating of 15 amperes. To clean the center console ashtray, remove the entire ashtray and empty it. Notice: ﬂammable items in the ashtray, hot cigarettes or other smoking materials could ignite them and possibly damage your vehicle. Never put ﬂammable items in the ashtray. If you put papers, pins, or other 153 Climate Controls Climate Control System With this system you can control the heating, cooling, and ventilation for the vehicle. Vehicles with Air Conditioning shown, without Air Conditioning similar Operation To change the current mode, select one of the following: H(Vent): This mode directs air to the instrument panel outlets. 154 )(Bi-Level): This mode directs about half of the air to the instrument panel outlets, and then directs the remaining air to the ﬂoor outlets. Cooler air is directed to the upper outlets and warmer air to the ﬂoor outlets. 6(Floor): This mode directs most of the air to the ﬂoor outlets with some air directed to the windshield and side windows. The left knob can also be used to select defog or defrost mode. Information on defogging and defrosting can be found later in this section. 9(Fan): Turn the center knob clockwise or counterclockwise to increase or decrease the fan speed. In any setting other than off, the fan will run continuously with the ignition on. The fan must be turned on to run the air conditioning compressor. 9(Off): To turn the fan off, turn the knob all the way counterclockwise to the off position. Temperature Control: Turn the right knob clockwise or counterclockwise to increase or decrease the temperature inside the vehicle. h(Recirculate): Press this button to prevent outside air and odors from entering the vehicle or to help heat or cool the air inside the vehicle more quickly. An indicator light above the button will come on in this mode. The air conditioning compressor also comes on. This mode is not available for ﬂoor, defog and defrost modes. When the recirculation button is pressed, the recirculate indicator light will ﬂash ﬁve times and outside air will be delivered. Operation in this mode during periods of high humidity and cool outside temperatures may result in increased window fogging. If window fogging is experienced, select the defrost mode. Outside Air: This mode allows outside air to circulate through the vehicle. This mode is automatically active if recirculate is not selected. There is no button for outside air. #(Air Conditioning): If your vehicle has air conditioning, press this button to turn the air conditioning system on or off. When this button is pressed, an indicator light above the button will come on to let you know the air conditioning is activated. On hot days, open the windows to let hot inside air escape; then close them. This helps to reduce the time it takes for the vehicle to cool down. It also helps the system to operate more efficiently. For quick cool down on hot days: 1. Select the vent mode. 2. Select the recirculation mode. 3. Select air conditioning. 4. Select the coolest temperature. 5. Select the highest fan speed. Using these settings together for long periods of time may cause the air inside of the vehicle to become too dry. To prevent this from happening, after the air in the vehicle has cooled, turn off the recirculation by pressing the button again. The air conditioning system removes moisture from the air, so you may sometimes notice a small amount of water dripping underneath your vehicle while idling or after turning off the engine. This is normal. The air conditioning compressor cannot be turned on when the fan is off. 155 Defogging and Defrosting Fog on the inside of windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control system is used properly. There are two modes to clear fog or frost from the windshield and side windows. Use the defog mode to clear the windows of fog or moisture and warm the passengers. Use the defrost mode to remove fog or frost from the windshield more quickly. For best results, clear all snow and ice from the windshield before defrosting. Turn the left knob to select the defog or defrost mode. -(Defog): This mode directs about half of the air to the windshield and the side window outlets and half to the ﬂoor outlets. When you select this mode the system runs the air conditioning compressor. To defog the windows faster, turn the temperature control knob clockwise to the warmest setting. 0(Defrost): This mode directs most of the air to the windshield, with some air directed to the side window outlets and the ﬂoor outlets. When you select this mode the system runs the air conditioning compressor. To defrost the windows faster, turn the temperature control knob clockwise to the warmest setting. Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. The rear window defogger will only work when the ignition is in RUN. <(Rear): Press the button to turn the rear window defogger on or off. Be sure to clear as much snow from the rear window as possible. An indicator light above the button will come on to let you know that the rear window defogger is activated. 156 The rear window defogger will turn off about 15 minutes after the button is pressed. If turned on again, the defogger will only run for about seven minutes before turning off. If the vehicle is moving faster than 50 mph (80 kph), the rear defogger will stay on. The defogger can also be turned off by pressing the button again or by turning off the engine. Notice: Do not use anything sharp on the inside of the rear window. If you do, you could cut or damage the warming grid, and the repairs would not be covered by your warranty. Do not attach a temporary vehicle license, tape, a decal or anything similar to the defogger grid. Outlet Adjustment Use the thumbwheels located next to and below the air outlets to change the direction of the airﬂow and to open and close the outlets. Operation Tips (cid:127) Clear away any ice, snow or leaves from the air inlets at the base of the windshield that may block the ﬂow of air into your vehicle. (cid:127) Use of non-GM approved hood deﬂectors may adversely affect the performance of the system. (cid:127) Keep the path under the front seats clear of objects to help circulate the air inside of your vehicle more effectively. 157 Passenger Compartment Air Filter Passenger compartment air, both outside air and recirculated air, is routed through a passenger compartment ﬁlter. The ﬁlter removes certain particles from the air, including pollen and dust particles. Reductions in airﬂow, which may occur more quickly in dusty areas, indicate that the ﬁlter needs to be replaced early. The ﬁlter should be replaced as part of routine scheduled maintenance. See Scheduled Maintenance on page 391 for replacement intervals. See your dealer for details on changing the ﬁlter. To ﬁnd out what type of ﬁlter to use, see Normal Maintenance Replacement Parts on page 404. To access the passenger compartment air ﬁlter you must go through the glove box. 1. Open the glove box and remove all articles from the inside. 158 2. Tilt the glove box door down by squeezing on each side of the glove box until the door can be lowered from its track. Lower the glove box door. 3. Open the passenger compartment air ﬁlter door by reaching through the opening in the back of the glove box and raising the tab until the door can be opened downward. 4. Remove the ﬁlter by sliding it out of the housing. When installing a new air ﬁlter make sure the AIR FLOW arrow is pointing downward. Reverse Steps 1 through 5 making sure the glove box door snaps back into place. 159 Gages can indicate when there may be or is a problem with one of your vehicle’s functions. Often gages and warning lights work together to let you know when there is a problem with your vehicle. When one of the warning lights comes on and stays on as you are driving, or when one of the gages shows there may be a problem, check the section that tells you what to do about it. Please follow this manual’s advice. Waiting to do repairs can be costly and even dangerous. So please get to know your warning lights and gages. They are a big help. Warning Lights, Gages, and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to your warning lights and gages could also save you or others from injury. Warning lights come on when there may be or is a problem with one of your vehicle’s functions. As you will see in the details on the next few pages, some warning lights come on brieﬂy when you start the engine just to let you know they are working. If you are familiar with this section, you should not be alarmed when this happens. 160 Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You will know how fast you are going, about how much fuel is left in the tank, and many other things you will need to drive safely and economically. United States SS Cluster shown, Canada and Base similar 161 Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your vehicle’s odometer works together with the driver information center. You can set a Trip A and Trip B odometer. See “Trip Information” under DIC Operation and Displays on page 178. The odometer mileage can be checked without the vehicle running. Simply open the driver’s door and the mileage will be displayed brieﬂy. If your vehicle ever needs a new odometer installed, the new one will be set to the correct mileage total of the old odometer. Tachometer The tachometer displays the engine speed in revolutions per minute (rpm). Notice: tachometer in the shaded warning area, your vehicle could be damaged, and the damages would not be covered by your warranty. Do not operate the engine with the tachometer in the shaded warning area. If you operate the engine with the 162 Safety Belt Reminder Light When the key is turned to RUN or START, a chime will sound for several seconds to remind you and your passengers to buckle your safety belts. The driver safety belt light will also come on and stay on for several seconds, then it will ﬂash for several more. You should buckle your seat belt. If the vehicle is equipped with the passenger sensing system, this chime and light will be repeated if the driver remains unbuckled and the vehicle is in motion. If the driver’s belt is buckled, neither the chime nor the light will come on. See Passenger Sensing System on page 75 for more information. Passenger Safety Belt Reminder Light If equipped, several seconds after the key is turned to RUN or START, a chime will sound for several seconds to remind the front passenger to buckle their safety belt. This would only occur if the passenger airbag is enabled. See Passenger Sensing System on page 75 for more information. The passenger safety belt light will also come on and stay on for several seconds, then it will ﬂash for several more. Airbag Readiness Light There is an airbag readiness light on the instrument panel cluster, which shows the airbag symbol. The system checks the airbag’s electrical system for malfunctions. The light tells you if there is an electrical problem. The system check includes the airbag sensor, the airbag modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 66. This chime and light will be repeated if the passenger remains unbuckled and the vehicle is in motion. If the passenger’s safety belt is buckled, neither the chime nor the light will come on. This light will come on when you start your vehicle, and it will ﬂash for a few seconds. Then the light should go out. This means the system is ready. 163 If the airbag readiness light stays on after you start the vehicle or comes on when you are driving, your airbag system may not work properly. Have your vehicle serviced right away. {CAUTION: If the airbag readiness light stays on after you start your vehicle, it means the airbag system may not be working properly. The airbags in your vehicle may not inﬂate in a crash, or they could even inﬂate without a crash. To help avoid injury to yourself or others, have your vehicle serviced right away if the airbag readiness light stays on after you start your vehicle. The airbag readiness light should ﬂash for a few seconds when you turn the ignition key to RUN. If the light does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. 164 Passenger Airbag Status Indicator If your vehicle has the passenger sensing system, then your instrument panel has a passenger airbag status indicator. See Passenger Sensing System on page 75. United States Canada When the ignition key is turned to RUN or START, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check. Then, after several more seconds, the status indicator will light either ON or OFF, or either the on or off symbol to let you know the status of the right front passenger’s frontal airbag. If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger’s frontal airbag is enabled (may inﬂate). {CAUTION: {CAUTION: If the on indicator comes on when you have a rear-facing child restraint installed in the right front passenger’s seat, it means that the passenger sensing system has not turned off the passenger’s frontal airbag. A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inﬂates. This is because the back of the rear-facing child restraint would be very close to the inﬂating airbag. Do not use a rear-facing child restraint in the right front passenger’s seat if the airbag is turned on. Your vehicle has a rear seat that will accommodate a rear-facing child restraint. A label on your sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys. Even though the passenger sensing system is designed to turn off the passenger’s frontal airbag if the system detects a rear-facing child restraint, no system is failsafe, and no one can guarantee that an airbag will not deploy under some unusual circumstance, even though it is turned off. We recommend that rear-facing child restraints be secured in the rear seat, even if the airbag is off. If the word OFF or the off symbol is lit on the airbag status indicator, it means that the passenger sensing system has turned off the right front passenger’s frontal airbag. See Passenger Sensing System on page 75 for more on this, including important safety information. 165 If, after several seconds, all status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service. {CAUTION: If the off indicator and the airbag readiness light ever come on together, it means that something may be wrong with the airbag system. If this ever happens, have the vehicle serviced promptly, because an adult-size person sitting in the right front passenger seat may not have the protection of the frontal airbag. See Airbag Readiness Light on page 163. Charging System Light The charging system light will come on brieﬂy when you turn on the ignition, and the engine is not running, as a check to show you it is working. Then it should go out when the engine is started. If it stays on, or comes on while you are driving, you may have a problem with the electrical charging system. Have it checked by your dealer. Driving while this light is on could drain your battery. If you must drive a short distance with the light on, be certain to turn off all your accessories, such as the radio and air conditioner. 166 Up-Shift Light Your vehicle may have an up-shift light. When this light comes on, you should shift to the next higher gear if weather, road, and traffic conditions allow you to. This light is located in your instrument panel cluster to the left of the tachometer. Brake System Warning Light Your vehicle’s hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop you. For good braking, though, you need both parts working well. If the warning light comes on, there is a brake problem. Have your brake system inspected right away. United States Only See Manual Transaxle Operation on page 118 for more information. United States Canada This light should come on brieﬂy when you turn the ignition key to RUN. If it does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. 167 When the ignition is on, the brake system warning light will also come on when you set your parking brake. The light will stay on if your parking brake does not release fully. If it stays on after your parking brake is fully released, it means you have a brake problem. If the light comes on while you are driving, pull off the road and stop carefully. Make sure the parking brake is fully released. You may notice that the pedal is harder to push or, the pedal may go closer to the ﬂoor. It may take longer to stop. If the light is still on, have the vehicle towed for service. See Towing Your Vehicle on page 258. {CAUTION: Your brake system may not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to an accident. If the light is still on after you have pulled off the road and stopped carefully, have the vehicle towed for service. 168 Anti-Lock Brake System Warning Light Your vehicle may have an Anti-Lock Brake System (ABS) warning light. The ABS warning light will come on brieﬂy when you turn the ignition key to RUN. This is normal. If the light does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. If the light stays on, turn the ignition off, if the light comes on when you are driving, stop as soon as possible and turn the ignition off. Then start the engine again to reset the system. If the light still stays on, or comes on again while you are driving, your vehicle needs service. If the regular brake system warning light is not on, you still have brakes, but you do not have anti-lock brakes. If the regular brake system warning light is also on, you do not have anti-lock brakes and there is a problem with your regular brakes. See Brake System Warning Light on page 167. Enhanced Traction System Warning Light If your vehicle is equipped with the Enhanced Traction System (ETS), this warning light should come on brieﬂy as you start the engine. If the warning light does not come on, then have it ﬁxed so it will be ready to warn you if there is a problem. If the warning light stays on, or comes on when you are driving, there may be a problem with your Enhanced Traction System and your vehicle may need service. When this warning light is on, the system will not limit wheel spin. Adjust your driving accordingly. (cid:127) The Enhanced Traction System warning light may come on for the following reasons: (cid:127) If you turn the system off by moving the shift lever to LOW (L), the warning light will come on and stay on. To turn the system back on, move the shift lever back to a position other than LOW (L). The warning light should go off. See Enhanced Traction System (ETS) on page 230 for more information. (cid:127) The warning light will come on when you set your parking brake with the engine running, and it will stay on if your parking brake does not release fully. If the transaxle shift lever is in any position other than LOW (L) and the warning light stays on after your parking brake is fully released, it means there is a problem with the system. If the traction control system is affected by an engine-related problem, the system will turn off and the warning light will come on. If the Enhanced Traction System warning light comes on and stays on for an extended period of time when the transaxle shift lever is in any position other than LOW (L), your vehicle needs service. 169 Engine Coolant Temperature Warning Light Malfunction Indicator Lamp Check Engine Light The engine coolant temperature warning light will come on when the engine has overheated. Your vehicle has a computer which monitors operation of the fuel, ignition, and emission control systems. If this happens you should pull over and turn off the engine as soon as possible. See Engine Overheating on page 303 for more information. Notice: Driving with the engine coolant temperature warning light on could cause your vehicle to overheat. See Engine Overheating on page 303. Your vehicle could be damaged, and it might not be covered by your warranty. Never drive with the engine coolant temperature warning light on. This light will also come on when starting your vehicle. If it doesn’t, have your vehicle serviced. This system is called OBD II (On-Board Diagnostics-Second Generation) and is intended to assure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment. The check engine light comes on to indicate that there is a problem and service is required. Malfunctions often will be indicated by the system before any problem is apparent. This may prevent more serious damage to your vehicle. This system is also designed to assist your service technician in correctly diagnosing any malfunction. 170 If you keep driving your vehicle with Notice: this light on, after awhile, your emission controls may not work as well, your fuel economy may not be as good, and your engine may not run as smoothly. This could lead to costly repairs that may not be covered by your warranty. Notice: Modiﬁcations made to the engine, transaxle, exhaust, intake, or fuel system of your vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect your vehicle’s emission controls and may cause this light to come on. Modiﬁcations to these systems could lead to costly repairs not covered by your warranty. This may also result in a failure to pass a required Emission Inspection/Maintenance test. See Accessories and Modiﬁcations on page 274. This light should come on, as a check to show you it is working, when the ignition is on and the engine is not running. If the light does not come on, have it repaired. This light will also come on during a malfunction in one of two ways: (cid:127) Light Flashing — A misﬁre condition has been detected. A misﬁre increases vehicle emissions and may damage the emission control system on your vehicle. Diagnosis and service may be required. (cid:127) Light On Steady — An emission control system malfunction has been detected on your vehicle. Diagnosis and service may be required. 171 If the Light is Flashing The following may prevent more serious damage to your vehicle: (cid:127) Reducing vehicle speed (cid:127) Avoiding hard accelerations (cid:127) Avoiding steep uphill grades (cid:127) If you are towing a trailer, reduce the amount of cargo being hauled as soon as it is possible If the light stops ﬂashing and remains on steady, see “If the Light Is On Steady” following. If the light continues to ﬂash, when it is safe to do so, stop the vehicle. Find a safe place to park your vehicle. Turn the key off, wait at least 10 seconds and restart the engine. If the light remains on steady, see “If the Light Is On Steady” following. If the light is still ﬂashing, follow the previous steps, and see your dealer for service as soon as possible. If the Light Is On Steady You may be able to correct the emission system malfunction by considering the following: Did you recently put fuel into your vehicle? If so, reinstall the fuel cap, making sure to fully install the cap. See Filling the Tank on page 280. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap will allow fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off. Did you just drive through a deep puddle of water? If so, your electrical system may be wet. The condition will usually be corrected when the electrical system dries out. A few driving trips should turn the light off. 172 Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel. See Gasoline Octane on page 277. Poor fuel quality will cause your engine not to run as efficiently as designed. You may notice this as stalling after start-up, stalling when you put the vehicle into gear, misﬁring, hesitation on acceleration, or stumbling on acceleration. (These conditions may go away once the engine is warmed up.) This will be detected by the system and cause the light to turn on. If you experience one or more of these conditions, change the fuel brand you use. It will require at least one full tank of the proper fuel to turn the light off. If none of the above steps have made the light turn off, your dealer can check the vehicle. Your dealer has the proper test equipment and diagnostic tools to ﬁx any mechanical or electrical problems that may have developed. Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or may begin programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration. Here are some things you need to know to help your vehicle pass an inspection: Your vehicle will not pass this inspection if the check engine light is on or not working properly. Your vehicle will not pass this inspection if the OBD (on-board diagnostic) system determines that critical emission control systems have not been completely diagnosed by the system. The vehicle would be considered not ready for inspection. This can happen if you have recently replaced your battery or if your battery has run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This may take several days of routine driving. If you have done this and your vehicle still does not pass the inspection for lack of OBD system readiness, your dealer can prepare the vehicle for inspection. 173 Oil Pressure Light If you have a low engine oil pressure problem, this light will stay on after you start your engine, or come on when you are driving. This indicates that your engine is not receiving enough oil. The engine could be low on oil, or could have some other oil problem. Have it ﬁxed immediately. The oil light could also come on in three other situations: (cid:127) When the ignition is on but the engine is not running, the light will come on as a test to show you it is working, but the light will go out when you turn the ignition to START. If it does not come on with the ignition on, you may have a problem with the fuse or bulb. Have it ﬁxed right away. (cid:127) (cid:127) If you are idling at a stop sign, the light may blink on and then off. If you make a hard stop, the light may come on for a moment. This is normal. {CAUTION: Do not keep driving if the oil pressure is low. If you do, your engine can become so hot that it catches ﬁre. You or others could be burned. Check your oil as soon as possible and have your vehicle serviced. Notice: Lack of proper engine oil maintenance may damage the engine. The repairs would not be covered by your warranty. Always follow the maintenance schedule in this manual for changing engine oil. 174 Security Light Highbeam On Light For information regarding this light, see Theft-Deterrent Systems on page 104. This light comes on when the high-beam headlamps are in use. Fog Lamp Light If equipped, the fog lamps light will come on when the fog lamps are in use. See Headlamp High/Low-Beam Changer on page 142. Fuel Gage Your fuel gage tells you about how much fuel you have left. The light will go out when the fog lamps are turned off. See Fog Lamps on page 150 for more information. 175 Boost Gage Here are four things that some owners ask about. None of these show a problem with your fuel gage: (cid:127) At the service station, the gas pump shuts off (cid:127) before the gage reads full. It takes a little more or less fuel to ﬁll up than the gage indicated. For example, the gage may have indicated the tank was half full, but it actually took a little more or less than half the tank’s capacity to ﬁll the tank. (cid:127) The gage moves a little when you turn a corner or speed up. (cid:127) The gage doesn’t go back to empty when you turn off the ignition. For your fuel tank capacity, see Capacities and Speciﬁcations on page 385. United States Canada If equipped, this gage is located near the driver’s side of the instrument panel cluster. This gage indicates vacuum during light to moderate throttle and boost under heavier throttle. 176 This gage displays the air pressure level in the intake manifold before it enters the engine’s combustion chamber. This gage is automatically centered at zero every time the ignition is turned to RUN. Actual vacuum or boost is displayed from this zero point. Changes in ambient pressure, such as driving in mountains and changing weather, will slightly change the zero reading. Driver Information Center (DIC) Your vehicle has a Driver Information Center (DIC). The DIC display gives you the status of many of your vehicle’s systems. The DIC is also used to display driver personalization menu modes and warning/status messages. All messages will appear in the DIC display, located at the bottom of the instrument panel cluster. The DIC buttons are located on the left side of the steering wheel. q (Information): Press this button to scroll through the vehicle information mode displays. r (Reset): Press this button to reset some vehicle information mode displays, select a personalization menu mode setting, or acknowledge a warning message. Press and hold the information and reset buttons at the same time for one second, then release the buttons to enter the personalization menu. See DIC Vehicle Personalization on page 182 for more information. 177 DIC Operation and Displays The DIC comes on when the ignition is on. The DIC has different modes which can be accessed by pressing the DIC buttons. The button functions are detailed in the following. Information Modes q (Information): Press this button to scroll through the following vehicle information modes: Outside Air Temperature and Odometer Press the information button until the outside air temperature and the odometer are displayed. This mode shows the temperature outside of the vehicle in either degrees Fahrenheit (°F) or degrees Celsius (°C) and the total distance the vehicle has been driven in either miles (mi) or kilometers (km). The outside air temperature will appear on the left side of the DIC display and the odometer will appear on the right side of the display. To change the DIC display to English or metric units, see “UNITS” under DIC Vehicle Personalization on page 182. 178 TRIP A or TRIP B Press the information button until TRIP A or TRIP B is displayed. These modes show the current distance traveled since the last reset for each trip odometer in either miles (mi) or kilometers (km). Both odometers can be used at the same time. Each trip odometer can be reset to zero separately by pressing and holding the reset button for a few seconds while the desired trip odometer is displayed. FUEL RANGE Press the information button until FUEL RANGE is displayed. This mode shows the remaining distance you can drive without refueling in either miles (mi) or kilometers (km). It is based on fuel economy and the fuel remaining in the tank. When the fuel level is low, FUEL RANGE LOW will display. The fuel economy data used to determine fuel range is an average of recent driving conditions. As your driving conditions change, this data is gradually updated. The FUEL RANGE mode cannot be reset. ECON (Economy) Press the information button until ECON is displayed. This mode shows how many miles per gallon (mpg) or liters per 100 kilometers (L/100 km) your vehicle is getting based on current and past driving conditions. Press and hold the reset button while ECON is displayed to reset the average fuel economy. Average fuel economy will then be calculated starting from that point. If the average fuel economy is not reset, it will be continually updated each time you drive. AV (Average) SPEED Press the information button until AV SPEED is displayed. This mode shows the vehicle’s average speed in miles per hour (mph) or kilometers per hour (km/h). Press and hold the reset button while AV SPEED is displayed to reset the average vehicle speed. OIL LIFE Press the information button until OIL LIFE is displayed. The engine oil life system shows an estimate of the oil’s remaining useful life. It will show 100% when the system is reset after an oil change. It will alert you to change your oil on a schedule consistent with your driving conditions. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Engine Oil on page 287 and Scheduled Maintenance on page 391. Always reset the engine oil life system after an oil change. See “How to Reset the Engine Oil Life System” under Engine Oil Life System on page 292. COOLANT Press the information button until COOLANT is displayed. This mode shows the temperature of the engine coolant in either degrees Fahrenheit (°F) or degrees Celsius (°C). 179 DIC Warnings and Messages These messages appear if there is a problem detected in one of your vehicle’s systems. A message will clear when the vehicle’s condition is no longer present. To acknowledge a message and clear it from the display, press and hold any of the DIC buttons. If the condition is still present, the warning message will come back on the next time the vehicle is turned off and back on. With most messages, a warning chime sounds when the message displays. Your vehicle may have other warning messages. AUTO (Automatic) LIGHTS OFF This message displays if the automatic headlamp system is disabled with the headlamp switch. AUTO (Automatic) LIGHTS ON This message displays if the automatic headlamp system is enabled with the headlamp switch. BRAKE FLUID This message displays to inform the driver that the brake ﬂuid level is low while the ignition is on. The brake system warning light on the instrument panel cluster also comes on. See Brake System Warning Light on page 167 for more information. Have the brake system serviced by your dealer as soon as possible. CHANGE OIL SOON This message displays when the life of the engine oil has expired and it should be changed. When you acknowledge the CHANGE OIL SOON message by clearing it from the display, you still must reset the engine oil life system separately. See Engine Oil Life System on page 292 and Scheduled Maintenance on page 391 for more information. CHECK GAS CAP This message displays if the fuel cap has not been fully tightened. Recheck the fuel cap to make sure that it is on properly. A few driving trips with the cap properly installed should turn the message off. 180 COOLING MODE ON This message may display on some vehicles. Under severe conditions, hot ambient temperatures, steep grades, and towing, your vehicle may experience more transaxle shifting. This is temporary and normal under these conditions. This does not require engine or transaxle service. CRUISE ENGAGED This message displays when the cruise control system is active. See Cruise Control on page 145 for more information. DOOR AJAR This message displays if one or more of the vehicle’s doors are not closed properly. When this message displays, make sure that the door(s) are closed completely. ENGINE DISABLED This message displays if the starting of the engine is disabled. Have your vehicle serviced by your dealer immediately. ENG (Engine) PWR (Power) REDUCED This message displays to inform you that the vehicle has reduced engine power to avoid damaging the engine. Reduced engine power can affect the vehicle’s ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer for service as soon as possible. ICE POSSIBLE This message displays when the outside air temperature is cold enough to create icy road conditions. Adjust your driving accordingly. KEY FOB BATT (Battery) LOW This message displays if the Remote Keyless Entry (RKE) transmitter battery is low. Replace the battery in the transmitter. See “Battery Replacement” under Remote Keyless Entry (RKE) System Operation on page 89. 181 LOW COOLANT If your vehicle has a 2.0L engine, this message displays when there is a low level of engine coolant. Have the cooling system serviced by your dealer as soon as possible. See Engine Coolant on page 296 for more information. LOW FUEL This message displays when your vehicle is low on fuel. Reﬁll the fuel tank as soon as possible. See Fuel Gage on page 175, Fuel on page 276, and Filling the Tank on page 280 for more information. LOW TRACTION This message displays when the Enhanced Traction System (ETS) is actively limiting wheel spin. Slippery road conditions may exist if this message displays, so adjust your driving accordingly. See Enhanced Traction System (ETS) on page 230 for more information. PARKING BRAKE This message displays if the parking brake is left engaged. See Parking Brake on page 120 for more information. 182 POWER STEERING This message displays if a problem has been detected with the electric power steering. Have your vehicle serviced by your dealer immediately. SERVICE AIR BAG This message displays when there is a problem with the airbag system. Have your vehicle serviced by your dealer immediately. TRUNK AJAR This message displays when the trunk lid is not closed completely. Make sure that the trunk lid is closed completely. See Trunk on page 100. DIC Vehicle Personalization Your vehicle has personalization capabilities that allow you to program certain features to a preferred setting. All of the features listed may not be available on your vehicle. Only the features available will be displayed on the DIC. The default settings for the features were set when your vehicle left the factory, but may have been changed from their default state since that time. To change feature settings, use the following procedure: Entering Personalization Menu 1. Turn the ignition on while the vehicle is stopped. To avoid excessive drain on the battery, it is recommended that the headlamps are turned off. 2. Press and hold the information and reset buttons at the same time for one second, then release to enter the personalization menu. If the vehicle speed is greater than 2 mph (3 km/h), only the UNITS menu will be accessible. 3. Press the information button to scroll through the available personalization menu modes. Press the reset button to scroll through the available settings for each mode. If you do not make a selection within ten seconds, the display will go back to the previous information displayed. Personalization Menu Modes OIL LIFE RESET When this feature is displayed, you can reset the engine oil life system. To reset the system, see Engine Oil Life System on page 292. See “OIL LIFE” under DIC Operation and Displays on page 178 for more information. UNITS This feature allows you to select the units of measurement in which the DIC will display the vehicle information. When UNITS appears on the display, press and hold the reset button for at least one second to scroll through the available settings: ENGLISH (default in United States): All information will be displayed in English units. For example, distance will be shown in miles (mi) and fuel economy in miles per gallon (mpg). METRIC (default in Canada): All information will be displayed in metric units. For example, distance will be shown in kilometers (km) and fuel economy in liters per 100 kilometers (L/100 km). Choose one of the available settings and press the information button to select it and move on to the next feature. 183 LOCK HORN If your vehicle has Remote Keyless Entry (RKE), this feature, which allows the vehicle’s horn to chirp every time the lock button on the RKE transmitter is pressed, can be enabled or disabled. When LOCK HORN appears on the display, press and hold the reset button for at least one second to scroll through the available settings: UNLOCK HORN If your vehicle has Remote Keyless Entry (RKE), this feature, which allows the vehicle’s horn to chirp on the ﬁrst press of the unlock button on the RKE transmitter, can be enabled or disabled. When UNLOCK HORN appears on the display, press and hold the reset button for at least one second to scroll through the available settings: OFF (default): The horn will not chirp on the ﬁrst press of the lock button on the RKE transmitter. The horn will still chirp on the second press. ON: The horn will chirp on the ﬁrst press of the lock button on the RKE transmitter. See Remote Keyless Entry (RKE) System Operation on page 89 for more information. Choose one of the available settings and press the information button to select it and move on to the next feature. OFF (default): The horn will not chirp when the unlock button on the RKE transmitter is pressed. ON: The horn will chirp on the ﬁrst press of the unlock button on the RKE transmitter. See Remote Keyless Entry (RKE) System Operation on page 89 for more information. Choose one of the available settings and press the information button to select it and move on to the next feature. 184 LIGHT FLASH If your vehicle has Remote Keyless Entry (RKE), this feature, which allows the vehicle’s exterior hazard/turn signal lighting to ﬂash every time the lock, unlock, or trunk release buttons on the RKE transmitter are pressed, can be enabled or disabled. When LIGHT FLASH appears on the display, press and hold the reset button for at least one second to scroll through the available settings: OFF: The exterior hazard/turn signal lighting will not ﬂash when the lock, unlock, or trunk release buttons on the RKE transmitter are pressed. ON (default): The exterior hazard/turn signal lighting will ﬂash when the lock, unlock, or trunk release buttons on the RKE transmitter are pressed. See Remote Keyless Entry (RKE) System Operation on page 89 for more information. Choose one of the available settings and press the information button to select it and move on to the next feature. DELAY LOCK This feature, which delays the actual locking of the vehicle, can be enabled or disabled. When DELAY LOCK appears on the display, press and hold the reset button for at least one second to scroll through the available settings: ON (default): The doors will not lock until ﬁve seconds after the last door is closed. You can temporarily override delayed locking by pressing the power lock switch or the lock button on the Remote Keyless Entry (RKE) transmitter a second time. OFF: The doors will lock immediately when pressing the power lock switch or the lock button on the RKE transmitter. See Power Door Locks on page 97, Delayed Locking on page 97, and Remote Keyless Entry (RKE) System Operation on page 89 for more information. Choose one of the available settings and press the information button to select it and move on to the next feature. 185 UNLK (Unlock) (Automatic Transaxle Only) This screen displays only if your vehicle has an automatic transaxle and DRIVER or ALL is selected for the AUTO UNLK feature. This feature determines when the automatic door unlocking will occur. When UNLK appears on the display, press and hold the reset button for at least one second to scroll through the available settings: KEY OFF: The door(s) will unlock when the key is turned off. SHIFT TO P (Park) (default): The door(s) will unlock when the vehicle is shifted into PARK (P). See Programmable Automatic Door Unlock on page 98 for more information. Choose one of the available settings and press the information button to select it and move on to the next feature. AUTO UNLK (Unlock) This feature, which allows the vehicle to automatically unlock certain doors, can be enabled or disabled. When AUTO UNLK appears on the display, press and hold the reset button for at least one second to scroll through the available settings: ALL (default): All of the doors will automatically unlock. DRIVER: The driver’s door will automatically unlock. NONE: None of the doors will automatically unlock. You will need to manually unlock the doors. If you have a manual transaxle vehicle, the door(s) will automatically unlock when the ignition is turned off. If you have an automatic transaxle vehicle, you can select when the automatic unlocking will occur. See “UNLK (Unlock) (Automatic Transaxle Only)” following. See Programmable Automatic Door Unlock on page 98 for more information. Choose one of the available settings and press the information button to select it and move on to the next feature. 186 EXT (Exterior) LIGHTS If your vehicle has Remote Keyless Entry (RKE), this feature, which allows the vehicle’s exterior perimeter lighting to turn on each time the unlock button on the RKE transmitter is pressed, can be enabled or disabled. When EXT LIGHTS appears on the display, press and hold the reset button for at least one second to scroll through the available settings: OFF: The exterior perimeter lighting will not turn on when the unlock button on the RKE transmitter is pressed. ON (default): The exterior perimeter lighting will turn on when the unlock button on the RKE transmitter is pressed. See Remote Keyless Entry (RKE) System Operation on page 89 for more information. Choose one of the available settings and press the information button to select it and move on to the next feature. LANGUAGE This feature allows you to select the language in which the DIC will display. When LANGUAGE appears on the display, press and hold the reset button for at least one second to scroll through the available settings: ENGLISH (default): The DIC will display all information in English. FRENCH: The DIC will display all information in French. SPANISH: The DIC will display all information in Spanish. GERMAN: The DIC will display all information in German. Choose one of the available settings and press the information button to select it and exit out of the personalization menu mode. Exiting Personalization Menu The personalization menu will be exited when any

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2007 Chevrolet Cobalt Owners Manual