2005 Chevrolet Cobalt Owners Manual

Download PDF Manual
Trunk To release the trunklid from the outside, use the key or the remote keyless entry transmitter. 2. Close the door. When you want to open a rear door when the security lock is on, do the following: 1. Unlock the door using the remote keyless entry transmitter, the power door lock switch, or by lifting the rear door manual lock. 2. Open the door from the outside. To cancel the rear door security lock, do the following: 1. Unlock the door and open it from the outside. 2. Insert the key into the slot next to the rear door security lock label and turn it so the lock is in the vertical position. Lockout Protection If you press the power door lock switch when the key is in the ignition and any door is open, all the doors will lock and the driver’s door will unlock. Be sure to remove the key from the ignition when locking your vehicle. The lockout protection can be overridden by pressing and holding the power door lock in the lock position for three seconds. {CAUTION: It can be dangerous to drive with the trunk lid open because carbon monoxide (CO) gas can come into your vehicle. You cannot see or smell CO. It can cause unconsciousness and even death. If you must drive with the trunk lid open or if electrical wiring or other cable connections must pass through the seal between the body and the trunk lid: (cid:127) Make sure all other windows are shut. (cid:127) Turn the fan on your heating or cooling system to its highest speed and select the control setting that will force outside air into your vehicle. See Climate Control System in the Index. If you have air outlets on or under the instrument panel, open them all the way. See Engine Exhaust on page 2-29. 2-9 (cid:127) Remote Trunk Release Emergency Trunk Release Handle To open the trunk from inside the vehicle, press the remote trunk release button located inside the driver’s storage compartment located on the lower left side of the instrument panel. See Instrument Panel Overview on page 3-4 or Driver’s Storage Compartment on page 2-33. The remote trunk release will only work when either the ignition is in OFF or ACC, the parking brake is engaged, or the vehicle speed is less than 2 mph (3 km/h). 2-10 Notice: Using the emergency trunk release handle as a tie-down or anchor point when securing items in the trunk may damage it. Use the emergency trunk release handle only to help you open the trunk lid. There is a glow-in-the-dark emergency trunk release handle located on the inside of the trunk lid of your vehicle. This handle will glow following exposure to light. Pull the release handle and push the trunk lid open from the inside to open the trunk. Windows {CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather. Manual Windows If your vehicle has manual windows, use the window crank to open and close each window. 2-11 Express-Down Window The driver’s window switch has an express-down feature which allows the window to be lowered fully without continuously pressing the switch. This switch is labeled AUTO. Press the front of the switch to the ﬁrst position, and the driver’s window will open a small amount. Press the switch down fully and the window will go all the way down. To stop the window while it is lowering, pull the front of the switch. Window Lockout The driver’s window controls also include a lockout switch. Press the right side of the switch to prevent the rear passengers from using their window switches. The driver can still control all the windows with the lockout on. Press the switch to the left to return to normal window operation. A red bar on the right side of the switch indicates that the lockout feature is off. Power Windows Sedan Shown, Coupe Similar If your vehicle has power windows, the switches on the driver’s door armrest control each of the windows. In addition, each passenger’s door has a window switch that controls that door’s window. Press the front of the switch to open the window. Pull the front of the switch up to close it. 2-12 Sun Visors To block out glare, swing down the visor(s). The visors can also be detached from the center mount and swung to the side to cover the windows. Visor Vanity Mirror Your vehicle may have a driver’s side vanity mirror. Swing down the sun visor and lift the cover to expose the mirror. Theft-Deterrent Systems Vehicle theft is big business, especially in some cities. Although your vehicle has a number of theft-deterrent features, we know that nothing we put on it can make it impossible to steal. Content Theft-Deterrent Your vehicle may have a content theft-deterrent alarm system. Arming the System With the ignition off, you can arm the system by doing any one of the following: (cid:127) Press the remote keyless entry transmitter lock button. (cid:127) Press the power door lock switch while the driver’s door is open. Turn the driver’s door key lock cylinder clockwise. The system will arm either: thirty seconds after all the doors are closed, or sixty seconds with any door open. If you press the lock button on the transmitter a second time while all the doors are closed, the system will arm immediately. The system will still arm in sixty seconds if a door is open. When the open door is closed, it will also become armed. The security light will turn on to indicate that arming has been initiated. Once the system is armed, the security light will ﬂash once every three seconds. If the security light is ﬂashing twice per second, this means that a door is open. If you do not want to arm the system, you may lock the car with the manual lock knobs on the doors. 2-13 (cid:127) (cid:127) (cid:127) Disarming the System You can disarm the system by doing any one of the following: (cid:127) Press the remote keyless entry transmitter unlock button. Turn the ignition on. Turn the driver’s door key lock cylinder counterclockwise. If the system is armed and the trunk is opened using the trunk release button on the transmitter, the system will temporarily disarm itself and re-arm when the trunk has been closed. This allows the you to exit the vehicle, lock the doors using the transmitter, and open the trunk using the transmitter without having to disarm and re-arm the system. Once the system is disarmed, the security light will stop ﬂashing. 2-14 How the System Alarm is Activated If the system is armed, it can be activated by either: (cid:127) Opening the driver’s door or trunk. This will cause a ten second pre-alarm chirp followed by a thirty second full alarm of horn and lights. (cid:127) Opening any other door. This will immediately cause a full alarm of horn and lights for thirty seconds. When an alarm event has ﬁnished, the system will re-arm itself automatically. How to Turn Off the System Alarm To turn off the system alarm, do one of the following: (cid:127) Press the lock button on the remote keyless entry transmitter. The system will then re-arm itself. (cid:127) Press the unlock button on the remote keyless entry transmitter. This will also disarm the system. Insert the key in the driver’s door key lock cylinder and turn it counterclockwise. This will also disarm the system. Insert the key in the ignition and turn it on. This will also disarm the system. (cid:127) (cid:127) (cid:127) (cid:127) During normal operation, the security light will go off approximately three seconds after the key is turned to RUN following an engine start. The security light is located on the instrument panel cluster. See Instrument Panel Cluster on page 3-22. If the engine stalls and the security light ﬂashes, wait until the light stops ﬂashing before trying to restart the engine. Remember to release the key from START as soon as the engine starts. If the engine is running and the security light comes on, you will be able to restart the engine if you turn the engine off. However, your Passlock® system is not working properly and must be serviced by your dealer. Your vehicle is not protected by Passlock® at this time. See your dealer for service. Or see Roadside Assistance Program on page 7-6 for more information. You may also want to check the fuses. See Fuses and Circuit Breakers on page 5-91. Simulated Armed Mode If you choose not to arm the system or if proper arming cannot be completed, the Content Theft Deterrent system will ﬂash the security light once every three seconds after a one minute delay with all the doors closed. This ﬂashing serves as a visual deterrent; however, the system is not armed. How to Detect a Tamper Condition If you hear three chirps when you press the unlock, lock, or trunk release buttons on the remote keyless transmitter, it means that the content theft security system alarm was activated previously. Passive Arming If passive arming is enabled through the DIC, the system will arm itself 60 seconds after cycling the ignition off and closing all doors. Passlock® Your vehicle is equipped with the Passlock® theft-deterrent system. Passlock® is a passive theft-deterrent system. Passlock® enables fuel if the ignition lock cylinder is turned with a valid key. If a correct key is not used or the ignition lock cylinder is tampered with, fuel is disabled. 2-15 Starting and Operating Your Vehicle Ignition Positions With the key in the ignition switch, you can turn it to four different positions. New Vehicle Break-In Notice: Your vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: (cid:127) Do not drive at any one speed, fast or slow, for the ﬁrst 500 miles (805 km). Do not make full-throttle starts. (cid:127) Avoid making hard stops for the ﬁrst 200 miles (322 km) or so. During this time your new brake linings are not yet broken in. Hard stops with new linings can mean premature wear and earlier replacement. Follow this breaking-in guideline every time you get new brake linings. (cid:127) Do not tow a trailer during break-in. See Towing a Trailer (Manual Transaxle) on page 4-37 or Towing a Trailer (Automatic Transaxle) on page 4-38 for more information. 2-16 Notice: Using a tool to force the key from the ignition switch could cause damage or break the key. Use the correct key and turn the key only with your hand. Make sure the key is all the way in. If it is, turn the steering wheel left and right while you turn the key hard. If none of this works, then your vehicle needs service. 9(LOCK): This position locks your steering column. It is a theft-deterrent feature. You will only be able to remove your key when the ignition is turned to LOCK. If you have an automatic transaxle, the ignition switch cannot be turned to LOCK unless the shift lever is in PARK (P). {CAUTION: If you have a manual transaxle removing the key from the ignition switch will lock the steering column and result in a loss of ability to steer the vehicle. This could cause a collision. If you need to turn the engine off while the vehicle is moving, turn the key to ACC. ACC (ACCESSORY): This position operates some of your electrical accessories. It unlocks the steering wheel and ignition. R (RUN): This is the position the switch returns to after you start your engine and release the switch. The switch stays in the RUN position when the engine is running. But even when the ignition is not running, you can use RUN to operate your electrical accessories and to display some warning and indicator lights. / (START): This position starts the engine. When the engine starts, release the key. The ignition switch will return to RUN for normal driving. A warning tone will sound if you open the driver’s door when the key has not been removed from the ignition. Shift Lock Release The following procedure allows the ignition to be turned to LOCK and for ignition key removal in case of a dead battery or low voltage battery. 1. Make sure the shift lever is in PARK (P). 2. Using a tool, pry off the cover from the bottom of the steering column. 2-17 Retained Accessory Power (RAP) Your vehicle is equipped with a Retained Accessory Power (RAP) feature which will allow the radio, power windows and sunroof to continue to work up to 10 minutes after the ignition is turned to OFF. Your vehicle’s radio will work when the ignition key is in RUN or ACC. Once the key is turned from RUN to OFF, the radio, power windows and sunroof will continue to work for up to 10 minutes or until any door is opened. Starting the Engine Automatic Transaxle Move your shift lever to PARK (P) or NEUTRAL (N). Your engine will not start in any other position — that is a safety feature. To restart when you are already moving, use NEUTRAL (N) only. Notice: Shifting into PARK (P) with the vehicle moving could damage the transaxle. Shift into PARK (P) only when your vehicle is stopped. 3. Place your ﬁnger into the access hole and locate the plunger. 4. Press and hold the plunger toward the driver’s door while turning the ignition key to LOCK. Remove the key. Have your vehicle serviced at your GM dealer as soon as possible. 2-18 Manual Transaxle The shift lever should be in NEUTRAL and the parking brake engaged. Hold the clutch pedal to the ﬂoor and start the engine. Your vehicle will not start if the clutch pedal is not all the way down — that is a safety feature. Starting Procedure 1. With your foot off the accelerator pedal, turn your ignition to START. When the engine starts, let go of the key. The idle speed will go down as your engine gets warm. Notice: Holding your key in START for longer than 15 seconds at a time will cause your battery to be drained much sooner. And the excessive heat can damage your starter motor. Wait about 15 seconds between each try to help avoid draining your battery or damaging your starter. 2. If it does not start, wait about 15 seconds and try again to start the engine by turning the ignition to START. Wait about 15 seconds between each try. When your engine has run about 10 seconds to warm up, your vehicle is ready to be driven. Do not run your engine at high speed when it is cold. If the weather is below freezing (32°F or 0°C), let the engine run for a few minutes to warm up. 3. If your engine still will not start, or starts but then stops, it could be ﬂooded with too much gasoline. Try pushing your accelerator pedal all the way to the ﬂoor and holding it there as you hold the key in START for about three seconds. If the vehicle starts brieﬂy but then stops again, do the same thing, but this time keep the pedal down for ﬁve or six seconds. This clears the extra gasoline from the engine. Notice: Your engine is designed to work with the electronics in your vehicle. If you add electrical parts or accessories, you could change the way the engine operates. Before adding electrical equipment, check with your dealer. If you do not, your engine might not perform properly. Engine Coolant Heater If your vehicle has this feature, in very cold weather 0°F (−18°C) or colder, the engine coolant heater can help. You will get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle. At temperatures above 32°F (0°C), use of the coolant heater is not required. 2-19 To Use the Engine Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. For the 2.2L engine, the electrical cord is located on the passenger’s side of the vehicle between the strut and the air cleaner/ﬁlter. For the 2.0L engine, the electrical cord is located on the passenger’s side of the vehicle near the strut. 3. Plug it into a normal, grounded 110-volt AC outlet. {CAUTION: Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a ﬁre. You could be seriously injured. Plug the cord into a properly grounded three-prong 110-volt AC outlet. If the cord will not reach, use a heavy-duty three-prong extension cord rated for at least 15 amps. 4. Before starting the engine, be sure to unplug and store the cord as it was before to keep it away from moving engine parts. If you do not, it could be damaged. 2-20 How long should you keep the coolant heater plugged in? The answer depends on the outside temperature, the kind of oil you have, and some other things. Instead of trying to list everything here, we ask that you contact a GM dealer in the area where you will be parking your vehicle. The dealer can give you the best advice for that particular area. Automatic Transaxle Operation If your vehicle is equipped with an automatic transaxle, the shift lever is located on the console between the seats. There are several different positions for your shift lever. PARK (P): This position locks your front wheels. It is the best position to use when you start your engine because your vehicle cannot move easily. {CAUTION: It is dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set your parking brake and move the shift lever to PARK (P). See Shifting Into Park (P) (Automatic Transaxle) on page 2-26. If you are pulling a trailer, see Towing a Trailer (Manual Transaxle) on page 4-37 or Towing a Trailer (Automatic Transaxle) on page 4-38. Ensure the shift lever is fully in PARK (P) before starting the engine. Your vehicle has an automatic transaxle shift lock control system. You have to fully apply your regular brakes before you can shift from PARK (P) when the ignition key is in RUN. If you cannot shift out of PARK (P), ease pressure on the shift lever by pushing the shift lever all the way into PARK (P), or by releasing the shift lever button on ﬂoor shift console models as you maintain brake application. Then move the shift lever into the gear you want. Press the shift lever button before moving the shift lever. See Shifting Out of Park (P) (Automatic Transaxle) on page 2-28. REVERSE (R): Use this gear to back up. Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transaxle. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped. To rock your vehicle back and forth to get out of snow, ice or sand without damaging your transaxle, see If Your Vehicle is Stuck in Sand, Mud, Ice or Snow on page 4-29. 2-21 NEUTRAL (N): In this position, your engine does not connect with the wheels. To restart when you are already moving, use NEUTRAL (N) only. Also, use NEUTRAL (N) when your vehicle is being towed. {CAUTION: Shifting into a drive gear while your engine is running at high speed is dangerous. Unless your foot is ﬁrmly on the brake pedal, your vehicle could move very rapidly. You could lose control and hit people or objects. Do not shift into a drive gear while your engine is running at high speed. Notice: Shifting out of PARK (P) or NEUTRAL (N) while the engine is running at high speed may damage the transaxle. The repairs would not be covered by your warranty. Be sure the engine is not running at high speeds when shifting your vehicle. AUTOMATIC OVERDRIVE (D): This position is for normal driving with the automatic transaxle. If you need more power for passing, and you are: (cid:127) Going less than about 35 mph (55 km/h), push your accelerator pedal about halfway down. (cid:127) Going about 35 mph (55 km/h), push your accelerator all the way down. SECOND (2): This position is also used for normal driving. However, it offers braking from the engine for slight downgrades where the vehicle would otherwise accelerate due to steepness of grade. If repetitive shifts occur between third and fourth gears on steep uphills, this position can be used to prevent repetitive shifting. Fuel economy will be lower than AUTOMATIC OVERDRIVE (D). Here are some times you might choose SECOND (2) instead of AUTOMATIC OVERDRIVE (D): (cid:127) When driving on hilly, winding roads. (cid:127) When towing a trailer, so there is less shifting between gears. 2-22 FIRST (1): This position holds you in the lowest gear possible for the given vehicle speed. It provides more engine braking but lower fuel economy than SECOND (2). You can use it on very steep hills as a brake assist, or in deep snow or mud. Notice: Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transaxle. If you are stuck, do not spin the tires. When stopping on a hill, use the brakes to hold the vehicle in place. Manual Transaxle Operation This is your shift pattern. Here is how to operate your manual transaxle: FIRST (1): Press the clutch pedal and shift into FIRST (1). Then, slowly let up on the clutch pedal as you press the accelerator pedal. You can shift into FIRST (1) when you are going less than 20 mph (32 km/h). If you have come to a complete stop and it is hard to shift into FIRST (1), put the shift lever in NEUTRAL and let up on the clutch. Press the clutch pedal back down. Then shift into FIRST (1). SECOND (2): Press the clutch pedal as you let up on the accelerator pedal and shift into SECOND (2). Then, slowly let up on the clutch pedal as you press the accelerator pedal. THIRD (3), FOURTH (4) and FIFTH (5): Shift into THIRD (3), FOURTH (4) and FIFTH (5) the same way you do for SECOND (2). Slowly let up on the clutch pedal as you press the accelerator pedal. To stop, let up on the accelerator pedal and press the brake pedal. Just before the vehicle stops, press the clutch pedal and the brake pedal, and shift to NEUTRAL. 2-23 NEUTRAL: Use this position when you start or idle your engine. Up-Shift Light If you have a manual transaxle, you have an up-shift light. This light will show you when to shift to the next higher gear for the best fuel economy. United States Only When this light comes on, you can shift to the next higher gear if weather, road and traffic conditions let you. For the best fuel economy, accelerate slowly and shift when the light comes on. While you accelerate, it is normal for the light to go on and off if you quickly change the position of the accelerator. Ignore the light when you downshift. REVERSE (R): To back up, press down the clutch pedal and shift into REVERSE (R). Let up on the clutch pedal slowly while pressing the accelerator pedal. Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transaxle. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped. Also, use REVERSE (R), along with the parking brake, for parking your vehicle. Shift Speeds {CAUTION: If you skip a gear when you downshift, you could lose control of your vehicle. You could injure yourself or others. Don’t shift down more than one gear at a time when you downshift. 2-24 Parking Brake Manual Shift Automatic Shift The parking brake lever is located between the front seats. For vehicles equipped with an armrest, lift the console armrest in order to access the parking brake lever. 2-25 To set the parking brake, Hold the brake pedal down and pull up on the parking brake lever. If the ignition is on, the brake system warning light will come on. See Brake System Warning Light on page 3-27. To release the parking brake, hold the brake pedal down. Pull the parking brake lever up until you can press the release button. Hold the release button in as you move the brake lever all the way down. If you forget to release your parking brake, a chime will sound and a warning light will ﬂash when the parking brake is applied and the vehicle is moving faster than 5 mph (8 kph). See DIC Warnings and Messages on page 3-37. Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Verify that the parking brake is fully released and the brake warning light is off before driving. 2-26 Shifting Into Park (P) (Automatic Transaxle) {CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, use the steps that follow. If you are pulling a trailer, see Towing a Trailer (Manual Transaxle) on page 4-37 or Towing a Trailer (Automatic Transaxle) on page 4-38. 1. Hold the brake pedal down and set the parking brake. 2. Move the shift lever into PARK (P) by holding the button on the shift lever and pushing the lever all the way toward the front of the vehicle. 3. Turn the ignition key to LOCK. 4. Remove the key and take it with you. If you can leave your vehicle with the ignition key in your hand, your vehicle is in PARK (P). Torque Lock If you are parking on a hill and you do not shift your transaxle into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transaxle. You may ﬁnd it difficult to pull the shift lever out of PARK (P). This is called “torque lock.” To prevent torque lock, set the parking brake and then shift into PARK (P) properly before you leave the driver’s seat. To ﬁnd out how, see Shifting Into Park (P) (Automatic Transaxle) on page 2-26. When you are ready to drive, move the shift lever out of PARK (P) before you release the parking brake. If torque lock does occur, you may need to have another vehicle push yours a little uphill to take some of the pressure from the parking pawl in the transaxle, so you can pull the shift lever out of PARK (P). Leaving Your Vehicle With the Engine Running {CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch ﬁre. You or others could be injured. Do not leave your vehicle with the engine running. If you have to leave your vehicle with the engine running, be sure your vehicle is in PARK (P) and your parking brake is ﬁrmly set before you leave it. After you have moved the shift lever into PARK (P), hold the regular brake pedal down. Then, see if you can move the shift lever away from PARK (P) without ﬁrst pushing the button. If you can, it means that the shift lever was not fully locked into PARK (P). 2-27 Shifting Out of Park (P) (Automatic Transaxle) This vehicle is equipped with an electronic shift lock release system. The shift lock release is designed to: (cid:127) Prevent ignition key removal unless the shift lever is in PARK (P) with the shift lever button fully released, and prevent movement of the shift lever out of PARK (P) unless the ignition is in a position other than LOCK. The shift lock release is always functional except in the case of a an uncharged or low voltage (less than 9 volt) battery. If your vehicle has an uncharged battery or a battery with low voltage, try charging or jump starting the battery. See Jump Starting on page 5-40 for more information. If you still cannot move the shift lever from PARK (P), consult your dealer or a professional towing service. Parking Your Vehicle Before leaving your vehicle, fully press the clutch pedal in, move the shift lever into REVERSE (R), and ﬁrmly apply the parking brake. Once the shift lever has been placed in REVERSE (R) with the clutch pedal pressed in, you can turn the ignition key to LOCK, remove the key and release the clutch. See Manual Transaxle Operation on page 2-23. 2-28 (cid:127) Parking Over Things That Burn Engine Exhaust {CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: (cid:127) Your exhaust system sounds strange or different. (cid:127) Your vehicle gets rusty underneath. (cid:127) Your vehicle was damaged in a collision. (cid:127) Your vehicle was damaged when driving over high points on the road or over road debris. (cid:127) Repairs were not done correctly. (cid:127) Your vehicle or exhaust system had been modiﬁed improperly. If you ever suspect exhaust is coming into your vehicle: (cid:127) Drive it only with all the windows down to blow out any CO; and (cid:127) Have your vehicle ﬁxed immediately. 2-29 {CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass or other things that can burn. Running the Engine While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. {CAUTION: {CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. See the earlier caution under Engine Exhaust on page 2-29. Also, idling in a closed-in place can let deadly carbon monoxide (CO) into your vehicle even if the climate control fan is at the highest setting. One place this can happen is a garage. Exhaust — with CO — can come in easily. NEVER park in a garage with the engine running. Another closed-in place can be a blizzard. See Winter Driving on page 4-25. It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set your parking brake and move the shift lever to PARK (P). Follow the proper steps to be sure your vehicle will not move. See Shifting Into Park (P) (Automatic Transaxle) on page 2-26. If you are parking on a hill and if you are pulling a trailer, also see Towing a Trailer (Manual Transaxle) on page 4-37 or Towing a Trailer (Automatic Transaxle) on page 4-38. 2-30 Mirrors Manual Rearview Mirror To reduce glare from lamps behind you, move the lever toward you to the night position. Automatic Dimming Rearview Mirror The automatic dimming rearview mirror automatically dims to the proper level to minimize glare from lights behind you after dark. Outside Manual Mirror Adjust your outside mirror so you can just see the side of your vehicle and have a clear view of objects behind you. The mirror can be folded in to enter narrow areas. Outside Remote Control Mirror Adjust the outside mirrors so that the side of the vehicle can be seen while sitting in a comfortable driving position. Adjust the driver’s outside mirror with the control lever located on the driver’s door. To adjust the passenger’s outside mirror, sit in the driver’s seat and have a passenger adjust the mirror for you. The mirror is a manual fold design. Outside Power Mirrors If your vehicle has this feature, the outside power mirror control is located on the driver’s door armrest. Move the selector switch to the left or right to choose the driver’s side or passenger’s side mirror you want to adjust. Then press the control pad to move each mirror in the desired direction. Adjust each mirror so you can see the side of your vehicle and the area beside and behind your vehicle. 2-31 Outside Convex Mirror {CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes. The passenger’s side mirror is convex. A convex mirror’s surface is curved so more can be seen from the driver’s seat. It also makes things appear farther away than they really are. OnStar® System OnStar® uses global positioning system (GPS) satellite technology, wireless communications, and call centers to provide you with a wide range of safety, security, information, and convenience services. A complete OnStar® user’s guide and the terms and conditions of the OnStar® Subscription Service Agreement are included in the vehicle’s glove box literature. For more information, visit www.onstar.com or 2-32 www.onstarcanada.com. Contact OnStar® at 1-888-4-ONSTAR (1-888-466-7827), or press the OnStar® button to speak to an OnStar® advisor 24 hours a day, 7 days a week. Terms and conditions of the Subscription Service Agreement can be found at www.onstar.com or www.onstarcanada.com. OnStar® Services For new vehicles equipped with OnStar®, the Safe and Sound Plan is included for the ﬁrst year. You can extend this plan beyond the ﬁrst year, or upgrade to the Directions and Connections Plan to meet your needs. For more information, press the OnStar® button to speak with an advisor. Safe and Sound Plan (cid:127) Automatic Notiﬁcation of Airbag Deployment (cid:127) Emergency Services (cid:127) Roadside Assistance (cid:127) Stolen Vehicle Tracking (cid:127) AccidentAssist (cid:127) Remote Door Unlock/Vehicle Alert (cid:127) Remote Diagnostics (cid:127) Online Concierge Directions and Connections Plan (cid:127) All Safe and Sound Plan Services (cid:127) Driving Directions (cid:127) RideAssist Information and Convenience Services OnStar® Personal Calling As an OnStar® subscriber, the Personal Calling capability is available if your hand-held cell phone is lost, forgotten, or has a low battery. It is a hands-free wireless phone that is integrated into the vehicle. Calls can be placed nationwide using simple voice commands with no additional contracts and no additional roaming charges. To ﬁnd out more about OnStar® Personal Calling, refer to the OnStar® user’s guide in the vehicle’s glove box or visit www.onstar.com or www.onstarcanada.com; or speak with an OnStar® advisor by pressing the OnStar® button or by calling 1-888-4-ONSTAR (1-888-466-7827). OnStar® Virtual Advisor Virtual Advisor is a feature of OnStar® Personal Calling that uses minutes to access up-to-date weather and traffic reports for your area, news and sports updates, stock quotes, entertainment and more. Customize your information proﬁle at www.myonstar.com. See the OnStar® user’s guide for more information. Storage Areas Glove Box Open the glove box by lifting up on the lever. Close the glove box with a ﬁrm push. Cupholder(s) There are two cupholders located at the front of the center console, in front of the shift lever. There are also cupholder for the rear seat passengers located at the rear of the center console. Center Console Storage Area Your vehicle may have a center console armrest with storage area. Use the lever on the front of the console to open it. Driver’s Storage Compartment The driver’s storage compartment is located near the left side of the steering column on the bottom of the instrument panel. It can be used to store small items and contains the remote trunk release switch. For more information, see Remote Trunk Release under Trunk on page 2-9. 2-33 (cid:127) Convenience Net Your vehicle may have a convenience net. You will see it inside the back wall of the trunk. Put small loads behind the net. It can help keep them from falling over during sharp turns or quick starts and stops. Unclip a corner of the convenience net to ﬁt larger objects behind the net, then reclip it to secure them in place. The net is not for larger, heavier loads. Store them in the trunk as far forward as you can. You can unhook the net so that it will lie ﬂat when you are not using it. Sunroof Your vehicle may be equipped with a power sunroof. The switch that operates it is located on the headliner. To open or close the sunroof, the ignition must be turned to ON or ACC, or Retained Accessory Power (RAP) must be active. See Retained Accessory Power (RAP) on page 2-18. Press and hold the switch rearward to open the glass panel to the vent position. Press and hold the switch rearward a second time to open the sunroof. If the sunshade is closed, it will open automatically with the sunroof. To close the sunroof, press the switch forward and hold it until the sunroof is closed. The sunroof will stop if the switch is released. The sunshade must be closed manually. The sunroof glass panel cannot be opened or closed if the vehicle has an electrical failure. Notice: sliding glass panel, damage will occur and the sunroof may not open or close properly. Always close the glass panel before closing the sunshade. If you force the sunshade forward of the 2-34 Section 3 Instrument Panel Instrument Panel Overview ...............................3-4 Hazard Warning Flashers ................................3-6 Other Warning Devices ...................................3-6 Horn .............................................................3-6 Tilt Wheel .....................................................3-7 Turn Signal/Multifunction Lever .........................3-7 Turn and Lane-Change Signals ........................3-8 Headlamp High/Low-Beam Changer ..................3-8 Flash-to-Pass .................................................3-8 Windshield Wipers ..........................................3-9 Windshield Washer .......................................3-10 Cruise Control ..............................................3-10 Headlamps ..................................................3-13 Wiper Activated Headlamps ............................3-14 Headlamps on Reminder ................................3-14 Daytime Running Lamps (DRL) .......................3-14 Fog Lamps ..................................................3-15 Instrument Panel Brightness ...........................3-15 Dome Lamp .................................................3-15 Entry/Exit Lighting .........................................3-16 Mirror Reading Lamps ...................................3-16 Battery Run-Down Protection ..........................3-16 Accessory Power Outlets ...............................3-16 Ashtrays and Cigarette Lighter ........................3-17 Climate Controls ............................................3-17 Climate Control System .................................3-17 Outlet Adjustment .........................................3-20 Warning Lights, Gages, and Indicators ............3-21 Instrument Panel Cluster ................................3-22 Speedometer and Odometer ...........................3-24 Tachometer .................................................3-24 Safety Belt Reminder Light .............................3-24 Airbag Readiness Light ..................................3-25 Charging System Light ..................................3-26 Up-Shift Light ...............................................3-26 Brake System Warning Light ..........................3-27 Anti-Lock Brake System Warning Light .............3-28 Enhanced Traction System Warning Light .........3-28 Engine Coolant Temperature Warning Light ......3-29 Malfunction Indicator Lamp .............................3-30 Oil Pressure Light .........................................3-32 Security Light ...............................................3-33 Fog Lamp Light ............................................3-33 Highbeam On Light .......................................3-33 Fuel Gage ...................................................3-34 Boost Gage .................................................3-34 3-1 Section 3 Instrument Panel Driver Information Center (DIC) .......................3-35 DIC Operation and Displays ...........................3-35 DIC Warnings and Messages .........................3-37 DIC Vehicle Personalization ............................3-40 Audio System(s) .............................................3-45 Setting the Time for Radios without Radio Data Systems (RDS) ..................................3-45 Setting the Time for Radios with Radio Data Systems (RDS) ..................................3-46 Radio with CD (Base Level) ...........................3-46 Radio with CD (Up Level) ..............................3-51 Radio with CD (MP3) ....................................3-60 Theft-Deterrent Feature ..................................3-74 Audio Steering Wheel Controls .......................3-75 Radio Reception ...........................................3-75 Care of Your CDs .........................................3-76 Care of the CD Player ...................................3-76 Fixed Mast Antenna ......................................3-76 XM™ Satellite Radio Antenna System .............3-76 3-2 ✍ NOTES 3-3 Instrument Panel Overview 3-4 The main components of your instrument panel are the following: A. Side Window Outlets. See Climate Control System on page 3-17. B. Air Outlets. See Outlet Adjustment on page 3-20. C. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-7. D. Cruise Control Buttons (If Equipped). See Cruise Control on page 3-10. E. Audio Steering Wheel Controls (If Equipped). See Audio Steering Wheel Controls on page 3-75. F. Instrument Panel Cluster. See Instrument Panel Cluster on page 3-22. G. Windshield Wiper/Washer Controls. See Windshield Wipers on page 3-9 and Windshield Washer on page 3-10. H. Audio System. See Audio System(s) on page 3-45. I. Fog Lamp Button (If Equipped). See Fog Lamps on page 3-15. J. Trunk Release. See Trunk on page 2-9. K. Instrument Panel Brightness Control. See Instrument Panel Brightness on page 3-15. L. Horn. See Horn on page 3-6. M. Cigarette Lighter (If Equipped). Accessory Power Outlet (If Equipped). See Ashtrays and Cigarette Lighter on page 3-17 and Accessory Power Outlets on page 3-16. N. Shift Lever (Manual Shown). See Manual Transaxle Operation on page 2-23 and Automatic Transaxle Operation on page 2-20. O. Climate Controls. See Climate Control System on page 3-17. P. Heated Seats Button (If Equipped). See Heated Seats on page 1-4. Q. Glove Box. See Glove Box on page 2-33. 3-5 Hazard Warning Flashers Your hazard warning ﬂashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will ﬂash on and off. The hazard warning ﬂasher button is located near the center of the instrument panel. Your hazard warning ﬂashers work no matter what position your key is in, and even if the key is not in. Press the button to make the front and rear turn signal lamps ﬂash on and off. Press the button again to turn the ﬂashers off. When the hazard warning ﬂashers are on, your turn signals will not work. Other Warning Devices If you carry reﬂective triangles, you can set them up at the side of the road about 300 feet (100 m) behind your vehicle. Horn To sound the horn, press the center pad on the steering wheel. 3-6 Tilt Wheel A tilt wheel allows you to adjust the steering wheel before you drive. You can raise the steering wheel to the highest level to give your legs more room when you enter and exit the vehicle. The lever that allows you to tilt the steering wheel is located on the left side of the steering column. Turn Signal/Multifunction Lever To tilt the wheel, pull down the lever. Then move the wheel to a comfortable position, pull up the lever to lock the wheel in place. The lever on the left side of the steering column includes the following: (cid:127) G Turn and Lane-Change Signals. See Turn and Lane-Change Signals on page 3-8. (cid:127) 3 Headlamp High/Low-Beam Changer. See Headlamp High/Low-Beam Changer on page 3-8. Flash-to-Pass. See Flash-to-Pass on page 3-8. (cid:127) 2 Exterior Light Control. See Headlamps on page 3-13. 3-7 (cid:127) Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is ﬁnished, the lever will return automatically. Headlamp High/Low-Beam Changer To change the headlamps from low beam to high beam, push the turn signal lever away from you. When the high beams are on, this light on the instrument panel cluster will also be on. An arrow on the instrument panel cluster will ﬂash in the direction of the turn or lane change. To signal a lane change, just raise or lower the lever until the arrow starts to ﬂash. Hold it there until you complete your lane change. The lever will return by itself when you release it. As you signal a turn or a lane change, if the arrows ﬂash rapidly, a signal bulb may be burned out and other drivers will not see your turn signal. If a bulb is burned out, replace it to help avoid an accident. If the arrows do not go on at all when you signal a turn, check the fuse. See Fuses and Circuit Breakers on page 5-91. 3-8 To change the headlamps from high beam to low beam, pull the turn signal lever toward you. Flash-to-Pass This feature lets you use your high-beam headlamps to signal a driver in front of you that you want to pass. To use it, pull the turn signal/multifunction lever toward you until the high-beam headlamps come on, then release the lever to turn them off. Windshield Wipers Use this lever, located on the right side of the steering wheel, to operate the windshield wipers. 9(Off): Move the lever to this position to turn off the windshield wipers. & (Intermittent; Speed Sensitive Wipers): Move the lever to this position for intermittent or speed sensitive operation. When you select this position, the delay will vary depending on the vehicles speed, as well as, the manually selected delay. x (Delay): Move the lever to this position to choose a delayed wiping cycle. Turn the intermittent adjust band up and down to set for a shorter or longer delay between wipes. To the left of the adjust band are bars, increasing in size from bottom to top, that indicate the frequency of the wipes. Smaller bars mean the wipers movement is less frequent. Larger bars mean the movement is more frequent. 6 (Low Speed): Move the lever up to the ﬁrst setting past intermittent, for steady wiping at low speed. 1 (High Speed): Move the lever up to the second setting past intermittent, for wiping at high speed. 8 (Mist): Move the lever all the way down to this position for a single wiping cycle. Hold it there until the windshield wipers start; then let go. The windshield wipers will stop after one wiping cycle. If you want additional wiping cycles, hold the lever down longer. Damaged wiper blades may prevent you from seeing well enough to drive safely. To avoid damage, be sure to clear ice and snow from the wiper blades before using them. If the wiper blades are frozen to the windshield, carefully loosen or thaw them. If your blades do become damaged, get new blades or blade inserts. 3-9 Cruise Control With cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below 25 mph (40 km/h). {CAUTION: Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use your cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause needless wheel spinning, and you could lose control. Do not use cruise control on slippery roads. Heavy snow or ice can overload your wiper motor. A circuit breaker will stop the motor until it cools. Clear away snow or ice to prevent an overload. If the motor gets stuck, turn the wipers off, clear away the snow or ice, and then turn the wipers back on. As an added safety feature, if the wipers are on for more than 15 seconds, the vehicle’s headlamps will turn on automatically. They will turn off when the wipers are turned off. Windshield Washer To wash your windshield, press the button at the end of the lever until the washers begin. {CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. When you release the button, the washers will stop, but the wipers will continue to wipe for about three times or will resume the speed you were using before. 3-10 Setting Cruise Control {CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control. The cruise control buttons are located on the steering wheel. J (On/Off): Press this button to turn the cruise control system on and off. +RES (Resume): Press this part of the button to resume a set speed and to accelerate the speed. −SET (Set): Press this part of the button to set a speed and to decrease the speed. To set a speed do the following: 1. Press the on/off button to turn cruise control on. The indicator light on the button will come on. 2. Get to the speed you want. 3. Press the −SET part of the control button and release it. The CRUISE ENGAGED message will appear on the Driver Information Center (DIC) to show the system is engaged. 4. Take your foot off the accelerator pedal. When you apply the brakes or clutch, the cruise control will shut off. If the vehicle is in cruise control and the Traction Control System (TCS) begins to limit wheel spin, the cruise control will automatically disengage. See Enhanced Traction System (ETS) on page 4-8. When road conditions allow, the cruise control can be used again. 3-11 Resuming a Set Speed Suppose you set your cruise control at a desired speed and then you apply the brake. This, of course, disengages the cruise control. To return to your previously set speed, you do not need to go through the set process again. Once you’re going about 25 mph (40 km/h) or more, you can press the +RES part of the button brieﬂy. This will take you back up to your previously chosen speed and stay there. Increasing Speed While Using Cruise Control There are two ways to go to a higher speed. 1. Disengage the cruise control by applying the brake pedal but do not turn it off. Accelerate to a higher speed and reset the cruise control. 2. If the cruise control system is already engaged, press the +RES part of the button. Hold it there until you get up to the speed you want, and then release the button. To increase your speed in very small amounts, press the +RES part of the button brieﬂy and then release it. Each time you do this, your vehicle will go about 1 mph (1.6 km/h) faster. Reducing Speed While Using Cruise Control If the cruise control system is already engaged, (cid:127) Push and hold the −SET part of the button until you reach the lower speed you want, then release it. To slow down in very small amounts, push the −SET part of the button brieﬂy. Each time you do this, you’ll go about 1 mph (1.6 km/h) slower. Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase your speed. When you take your foot off the pedal, your vehicle will slow down to the cruise control speed you set earlier. Using Cruise Control on Hills How well your cruise control will work on hills depends upon your speed, load and the steepness of the hills. When going up steep hills, you may have to step on the accelerator pedal to maintain your speed. When going downhill, you may have to brake or shift to a lower gear to keep your speed down. Of course, applying the brake takes you out of cruise control. Many drivers ﬁnd this to be too much trouble and don’t use cruise control on steep hills. 3-12 (cid:127) Ending Cruise Control To end cruise control, step lightly on the brake pedal or the clutch if your vehicle has a manual transmission. Stepping on the brake pedal or clutch will only end the current cruise control session. Press the cruise control on/off button to turn the system completely off. Erasing Speed Memory When you turn off the cruise control or the ignition, your cruise control set speed memory is erased. Headlamps The lever on the left side of the steering column operates the exterior lamps. The exterior lamp switch has the following four positions: 2 (Headlamps): This position turns on the headlamps, parking lamps, and taillamps. ; (Parking Lamps): This position turns on the parking lamps and taillamps only. AUTO (Automatic Headlamp System): This position automatically turns on the Daytime Running Lamps during daytime, and the headlamps, parking lamps, and taillamps at night. P (Off/On): This position is the momentary Off/On switch for the Automatic Headlamp System. In Canada, this only works when the vehicle is in PARK (P). When operating in AUTO, a momentary turn of the switch to off/on will turn off the Automatic Headlamp System. An AUTO LIGHTS OFF message will display on the driver information center and a chime will sound. Rotating the switch to off/on again will turn the Automatic Headlamp System back on. An AUTO LIGHTS ON message will display on the driver information center. The Automatic Headlamp System is always turned on at the beginning of an ignition cycle. 3-13 Wiper Activated Headlamps This feature activates the headlamps and parking lamps after the windshield wipers are turned on. For this feature to work, automatic lighting must be enabled. See Headlamps on page 3-13 for additional information. When the ignition is turned off, the wiper-activated headlamps will immediately turn off. They will also turn off if the windshield wiper control is turned off. Headlamps on Reminder If you open the driver’s door with the ignition off and the lamps on, you will hear a warning chime. Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional daytime running lamps are required on all vehicles ﬁrst sold in Canada. Your vehicle has a light sensor on top of the instrument panel. Make sure it is not covered or the headlamps will come on when you do not need them. The DRL system will make both front turn signal lamps turn on when the following conditions are met: The ignition is on. The exterior lamp control is turned to AUTO. The light sensor detects daytime light. The shift lever is not in PARK (P). While the DRL system is on, the taillamps, sidemarker lamps, and instrument panel lights will not be illuminated. The DRL system will be off any time your vehicle is in PARK (P). The DRL system on U.S. vehicles can also be turned off by using the off/on switch for one ignition cycle. As with any vehicle, you should turn on the regular headlamp system when you need it. 3-14 (cid:127) (cid:127) (cid:127) (cid:127) Fog Lamps Instrument Panel Brightness The fog lamp button is located on the instrument panel, to the left of the steering wheel. The control for this feature is located on the instrument panel to the left of the steering wheel. The ignition must be on to turn your fog lamps on. Push the button to turn the fog lamps on. An indicator light in the instrument panel cluster will come on when the fog lamps are on. Push the button again to turn the fog lamps off. The parking lamps will automatically turn on and off when the fog lamps are turned on and off. The fog lamps will turn off while the high-beam headlamps are turned on. Turn the knob clockwise to brighten the lights or counterclockwise to dim them. Dome Lamp Your vehicle may have a dome lamp. 9(Off): Move the lever to this position to turn the lamp off, even when a door is opened. 1 (Door): Move the lever to this position to turn the lamp on whenever a door is opened. + (On): Move the lever to this position to turn the dome lamp on. 3-15 Entry/Exit Lighting The lamps inside your vehicle will go on when you open any door. These lamps will fade out after about 20 seconds after all of the doors have been closed or when the ignition is turned to ON. These lamps will also go on when you press the trunk release, unlock symbol button or the horn symbol on the keyless entry system transmitter. The lamps inside your vehicle will stay on for about 20 seconds after your key is removed from the ignition to provide an illuminated exit. Mirror Reading Lamps Your vehicle may have reading lamps on the rearview mirror. Push the button to turn the reading lamps on and off. Battery Run-Down Protection Your vehicle is equipped with a battery saver feature designed to protect your vehicle’s battery. When any interior lamp is left on and the ignition is turned off, the battery rundown protection system will automatically turn the lamp off after 20 minutes. This will avoid draining the battery. Accessory Power Outlets Accessory power outlets can be used to connect electrical equipment such as a cellular phone or CB radio. The outlet can accept electrical equipment rated at a maximum of 20 amps. The accessory power outlet is located in the center console, rearward of the shift lever. To use the outlet, remove the cover. When not in use, always cover the outlet with the protective cap. Notice: Leaving electrical equipment on for extended periods will drain the battery. Always turn off electrical equipment when not in use and do not plug in equipment that exceeds the maximum amperage rating. Certain electrical accessories may not be compatible with the accessory power outlet and could result in blown vehicle or adapter fuses. If you experience a problem, see your dealer for additional information on the accessory power outlet. Notice: Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should. The repairs would not be covered by your warranty. Check with your dealer before adding electrical equipment. 3-16 Improper use of the power outlet can cause When adding electrical equipment, be sure to follow the installation instructions included with the equipment. Notice: damage not covered by your warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only. Ashtrays and Cigarette Lighter Your vehicle may have an ashtray and cigarette lighter. To use the lighter, located on the instrument panel below the climate controls, push it in all the way and let go. When it is ready, it will pop back out by itself. Notice: Holding a cigarette lighter in while it is heating will not allow the lighter to back away from the heating element when it is hot. Damage from overheating may occur to the lighter or heating element, or a fuse could be blown. Do not hold a cigarette lighter in while it is heating. Do not use anything other than the cigarette lighter in the heating element. To clean the center console ashtray, remove the entire ashtray and empty it. Notice: If you put papers, pins, or other ﬂammable items in the ashtray, hot cigarettes or other smoking materials could ignite them and possibly damage your vehicle. Never put ﬂammable items in the ashtray. Climate Controls Climate Control System With this system you can control the heating, cooling, and ventilation for your vehicle. Vehicles with Air Conditioning shown, without Air Conditioning similar Operation To change the current mode, select one of the following: H (Vent): This mode directs air to the instrument panel outlets. 3-17 h (Recirculate): Press this button to prevent outside air and odors from entering your vehicle or to help heat or cool the air inside your vehicle more quickly. An indicator light above the button will come on in this mode. The air conditioning compressor also comes on. This mode is not available for ﬂoor, defog and defrost modes. When the recirculation button is pressed, the RECIRC indicator light will ﬂash ﬁve times and outside air will be delivered. Operation in this mode during periods of high humidity and cool outside temperatures may result in increased window fogging. If window fogging is experienced, select the defrost mode. Outside Air: This mode allows outside air to circulate through your vehicle. This mode is automatically active if recirculate is not selected. There is no button for outside air. #(Air Conditioning): If your vehicle has air conditioning, press this button to turn the air conditioning system on or off. When this button is pressed, an indicator light above the button will come on to let you know the air conditioning is activated. ) (Bi-Level): This mode directs approximately half of the air to the instrument panel outlets, and then directs the remaining air to the ﬂoor outlets. Cooler air is directed to the upper outlets and warmer air to the ﬂoor outlets. 6 (Floor): This mode directs most of the air to the ﬂoor outlets with some air directed to the windshield and side windows. The left knob can also be used to select defog or defrost mode. Information on defogging and defrosting can be found later in this section. Recirculation mode is not allowed in this mode. 9(Fan): Turn the center knob clockwise or counterclockwise to increase or decrease the fan speed. In any setting other than off, the fan will run continuously with the ignition on. The fan must be turned on to run the air conditioning (AC) compressor. 9 (Off): To turn the fan off, turn the knob all the way counterclockwise to the off position. Temperature Control: Turn the right knob clockwise or counterclockwise to increase or decrease the temperature inside your vehicle. 3-18 On hot days, open the windows to let hot inside air escape; then close them. This helps to reduce the time it takes for your vehicle to cool down. It also helps the system to operate more efficiently. For quick cool down on hot days: 1. Select the vent mode. 2. Select the recirculation mode. 3. Select air conditioning. 4. Select the coolest temperature. 5. Select the highest fan speed. Using these settings together for long periods of time may cause the air inside of your vehicle to become too dry. To prevent this from happening, after the air in your vehicle has cooled, turn off the recirculation by pressing the button again. The air conditioning system removes moisture from the air, so you may sometimes notice a small amount of water dripping underneath your vehicle while idling or after turning off the engine. This is normal. The air conditioning compressor cannot be turned on when the fan is off. Defogging and Defrosting Fog on the inside of windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control system is used properly. There are two modes to clear fog or frost from your windshield and side windows. Use the defog mode to clear the windows of fog or moisture and warm the passengers. Use the defrost mode to remove fog or frost from the windshield more quickly. For best results, clear all snow and ice from the windshield before defrosting. Turn the left knob to select the defog or defrost mode. -(Defog): This mode directs approximately half of the air to the windshield and the side window outlets and half to the ﬂoor outlets. When you select this mode the system runs the air conditioning compressor. To defog the windows faster, turn the temperature control knob clockwise to the warmest setting. Recirculation mode is not available in defog mode. 3-19 0(Defrost): This mode directs most of the air to the windshield, with some air directed to the side window outlets and the ﬂoor outlets. When you select this mode the system runs the air conditioning compressor. To defrost the windows faster, turn the temperature control knob clockwise to the warmest setting. Recirculation mode is not available in defog mode. Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. The rear window defogger will only work when the ignition is in RUN. < (Rear): Press the button to turn the rear window defogger on or off. Be sure to clear as much snow from the rear window as possible. An indicator light above the button will come on to let you know that the rear window defogger is activated. The rear window defogger will turn off approximately 15 minutes after the button is pressed. If turned on again, the defogger will only run for approximately seven minutes before turning off. The defogger can also be turned off by pressing the button again or by turning off the engine. 3-20 Notice: Do not use anything sharp on the inside of the rear window. If you do, you could cut or damage the warming grid, and the repairs would not be covered by your warranty. Do not attach a temporary vehicle license, tape, a decal or anything similar to the defogger grid. Outlet Adjustment Use the thumbwheels located next to and below the air outlets to change the direction of the airﬂow and to open and close the outlets. Operation Tips (cid:127) Clear away any ice, snow or leaves from the air inlets at the base of the windshield that may block the ﬂow of air into your vehicle. (cid:127) Use of non-GM approved hood deﬂectors may adversely affect the performance of the system. (cid:127) Keep the path under the front seats clear of objects to help circulate the air inside of your vehicle more effectively. Warning Lights, Gages, and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to your warning lights and gages could also save you or others from injury. Warning lights come on when there may be or is a problem with one of your vehicle’s functions. As you will see in the details on the next few pages, some warning lights come on brieﬂy when you start the engine just to let you know they’re working. If you are familiar with this section, you should not be alarmed when this happens. Gages can indicate when there may be or is a problem with one of your vehicle’s functions. Often gages and warning lights work together to let you know when there’s a problem with your vehicle. When one of the warning lights comes on and stays on as you are driving, or when one of the gages shows there may be a problem, check the section that tells you what to do about it. Please follow this manual’s advice. Waiting to do repairs can be costly — and even dangerous. So please get to know your warning lights and gages. They’re a big help. 3-21 Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You will know how fast you are going, about how much fuel is left in the tank, and many other things you will need to drive safely and economically. United States Uplevel Cluster shown, Canada similar 3-22 United States Base Level Cluster shown, Canada similar 3-23 Safety Belt Reminder Light When the key is turned to RUN or START, a chime will come on for several seconds to remind people to fasten their safety belts, unless the driver’s safety belt is already buckled. The safety belt light will also come on and stay on for several seconds, then it will ﬂash for several more. If the driver’s belt is already buckled, neither the chime nor the light will come on. Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your vehicle’s odometer works together with the driver information center. You can set a Trip A and Trip B odometer. See “Trip Information” under DIC Operation and Displays on page 3-35. The odometer mileage can be checked without the vehicle running. Simply open the driver’s door and the mileage will be displayed brieﬂy. If your vehicle ever needs a new odometer installed, the new one will be set to the correct mileage total of the old odometer. Tachometer The tachometer displays the engine speed in revolutions per minute (rpm). Notice: tachometer in the shaded warning area, your vehicle could be damaged, and the damages would not be covered by your warranty. Do not operate the engine with the tachometer in the shaded warning area. If you operate the engine with the 3-24 Airbag Readiness Light There is an airbag readiness light on the instrument panel, which shows the airbag symbol. The system checks the airbag’s electrical system for malfunctions. The light tells you if there is an electrical problem. The system check includes the airbag sensor, the airbag modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 1-48. This light will come on when you start your vehicle, and it will ﬂash for a few seconds. Then the light should go out. This means the system is ready. If the airbag readiness light stays on after you start the vehicle or comes on when you are driving, your airbag system may not work properly. Have your vehicle serviced right away. {CAUTION: If the airbag readiness light stays on after you start your vehicle, it means the airbag system may not be working properly. The airbags in your vehicle may not inﬂate in a crash, or they could even inﬂate without a crash. To help avoid injury to yourself or others, have your vehicle serviced right away if the airbag readiness light stays on after you start your vehicle. The airbag readiness light should ﬂash for a few seconds when you turn the ignition key to RUN. If the light does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. 3-25 Charging System Light The charging system light will come on brieﬂy when you turn on the ignition, and the engine is not running, as a check to show you it is working. Up-Shift Light Your vehicle may have an up-shift light. When this light comes on, you should shift to the next higher gear if weather, road, and traffic conditions allow you to. This light is located in your instrument panel cluster to the left of the tachometer. Then it should go out when the engine is started. If it stays on, or comes on while you are driving, you may have a problem with the electrical charging system. Have it checked by your GM dealer. Driving while this light is on could drain your battery. If you must drive a short distance with the light on, be certain to turn off all your accessories, such as the radio and air conditioner. United States Only See Manual Transaxle Operation on page 2-23 for more information. 3-26 Brake System Warning Light Your vehicle’s hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop you. For good braking, though, you need both parts working well. If the warning light comes on, there is a brake problem. Have your brake system inspected right away. United States Canada This light should come on brieﬂy when you turn the ignition key to RUN. If it does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. When the ignition is on, the brake system warning light will also come on when you set your parking brake. The light will stay on if your parking brake does not release fully. If it stays on after your parking brake is fully released, it means you have a brake problem. If the light comes on while you are driving, pull off the road and stop carefully. You may notice that the pedal is harder to push. Or, the pedal may go closer to the ﬂoor. It may take longer to stop. If the light is still on, have the vehicle towed for service. See Towing Your Vehicle on page 4-35. {CAUTION: Your brake system may not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to an accident. If the light is still on after you have pulled off the road and stopped carefully, have the vehicle towed for service. 3-27 Anti-Lock Brake System Warning Light Enhanced Traction System Warning Light If your vehicle is equipped with the anti-lock brake system, the light will come on when your engine is started and may stay on for several seconds. That is normal. If your vehicle is equipped with the Enhanced Traction System (ETS), this warning light should come on brieﬂy as you start the engine. If the warning light does not come on, then have it ﬁxed so it will be ready to warn you if there is a problem. If the warning light stays on, or comes on when you are driving, there may be a problem with your Enhanced Traction System and your vehicle may need service. When this warning light is on, the system will not limit wheel spin. Adjust your driving accordingly. If the light stays on, turn the ignition to LOCK. Or, if the light comes on when you are driving, stop as soon as possible and turn the ignition off. Then start the engine again to reset the system. If the light still stays on, or comes on again while you are driving, your vehicle needs service. If the regular brake system warning light is not on, you still have brakes, but you do not have anti-lock brakes. If the regular brake system warning light is also on, you do not have anti-lock brakes and there is a problem with your regular brakes. See Brake System Warning Light on page 3-27. The anti-lock brake system warning light will come on brieﬂy when you turn the ignition key to RUN. This is normal. If the light does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. 3-28 The Enhanced Traction System warning light may come on for the following reasons: If you turn the system off by moving the shift lever to FIRST (1), the warning light will come on and stay on. To turn the system back on, move the shift lever back to a position other than FIRST (1). The warning light should go off. See Enhanced Traction System (ETS) on page 4-8 for more information. The warning light will come on when you set your parking brake with the engine running, and it will stay on if your parking brake does not release fully. If the transaxle shift lever is in any position other than FIRST (1) and the warning light stays on after your parking brake is fully released, it means there is a problem with the system. If the traction control system is affected by an engine-related problem, the system will turn off and the warning light will come on. If the Enhanced Traction System warning light comes on and stays on for an extended period of time when the transaxle shift lever is in any position other than FIRST (1), your vehicle needs service. Engine Coolant Temperature Warning Light The engine coolant temperature warning light will come on when the engine has overheated. If this happens you should pull over and turn off the engine as soon as possible. See Engine Overheating on page 5-29 for more information. Notice: Driving with the engine coolant temperature warning light on could cause your vehicle to overheat. See Engine Overheating on page 5-29. Your vehicle could be damaged, and it might not be covered by your warranty. Never drive with the engine coolant temperature warning light on. This light will also come on when starting your vehicle. If it doesn’t, have your vehicle serviced. 3-29 (cid:127) (cid:127) (cid:127) Malfunction Indicator Lamp Check Engine Light Your vehicle is equipped with a computer which monitors operation of the fuel, ignition, and emission control systems. This system is called OBD II (On-Board Diagnostics-Second Generation) and is intended to assure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment. The check engine light comes on to indicate that there is a problem and service is required. Malfunctions often will be indicated by the system before any problem is apparent. This may prevent more serious damage to your vehicle. This system is also designed to assist your service technician in correctly diagnosing any malfunction. Notice: light on, after awhile, your emission controls may not work as well, your fuel economy may not be as good, and your engine may not run as smoothly. This could lead to costly repairs that may not be covered by your warranty. If you keep driving your vehicle with this 3-30 Notice: Modiﬁcations made to the engine, transaxle, exhaust, intake, or fuel system of your vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect your vehicle’s emission controls and may cause this light to come on. Modiﬁcations to these systems could lead to costly repairs not covered by your warranty. This may also result in a failure to pass a required Emission Inspection/Maintenance test. This light should come on, as a check to show you it is working, when the ignition is on and the engine is not running. If the light does not come on, have it repaired. This light will also come on during a malfunction in one of two ways: Light Flashing — A misﬁre condition has been detected. A misﬁre increases vehicle emissions and may damage the emission control system on your vehicle. Diagnosis and service may be required. Light On Steady — An emission control system malfunction has been detected on your vehicle. Diagnosis and service may be required. (cid:127) (cid:127) If the Light is Flashing The following may prevent more serious damage to your vehicle: (cid:127) Reducing vehicle speed (cid:127) Avoiding hard accelerations (cid:127) Avoiding steep uphill grades If you are towing a trailer, reduce the amount of cargo being hauled as soon as it is possible If the light stops ﬂashing and remains on steady, see “If the Light Is On Steady” following. If the light continues to ﬂash, when it is safe to do so, stop the vehicle. Find a safe place to park your vehicle. Turn the key off, wait at least 10 seconds and restart the engine. If the light remains on steady, see “If the Light Is On Steady” following. If the light is still ﬂashing, follow the previous steps, and see your dealer for service as soon as possible. If the Light Is On Steady You may be able to correct the emission system malfunction by considering the following: Did you recently put fuel into your vehicle? If so, reinstall the fuel cap, making sure to fully install the cap. See Filling the Tank on page 5-8. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap will allow fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off. Did you just drive through a deep puddle of water? If so, your electrical system may be wet. The condition will usually be corrected when the electrical system dries out. A few driving trips should turn the light off. Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel. See Gasoline Octane on page 5-5. Poor fuel quality will cause your engine not to run as efficiently as designed. You may notice this as stalling after start-up, stalling when you put the vehicle into gear, misﬁring, hesitation on acceleration, or stumbling on acceleration. (These conditions may go away once the engine is warmed up.) This will be detected by the system and cause the light to turn on. If you experience one or more of these conditions, change the fuel brand you use. It will require at least one full tank of the proper fuel to turn the light off. If none of the above steps have made the light turn off, your dealer can check the vehicle. Your dealer has the proper test equipment and diagnostic tools to ﬁx any mechanical or electrical problems that may have developed. 3-31 (cid:127) Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or may begin programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration. Here are some things you need to know to help your vehicle pass an inspection: Your vehicle will not pass this inspection if the check engine light is on or not working properly. Your vehicle will not pass this inspection if the OBD (on-board diagnostic) system determines that critical emission control systems have not been completely diagnosed by the system. The vehicle would be considered not ready for inspection. This can happen if you have recently replaced your battery or if your battery has run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This may take several days of routine driving. If you have done this and your vehicle still does not pass the inspection for lack of OBD system readiness, your GM dealer can prepare the vehicle for inspection. Oil Pressure Light If you have a low engine oil pressure problem, this light will stay on after you start your engine, or come on when you are driving. This indicates that your engine is not receiving enough oil. The engine could be low on oil, or could have some other oil problem. Have it ﬁxed immediately. The oil light could also come on in three other situations: (cid:127) When the ignition is on but the engine is not running, the light will come on as a test to show you it is working, but the light will go out when you turn the ignition to START. If it does not come on with the ignition on, you may have a problem with the fuse or bulb. Have it ﬁxed right away. If you are idling at a stop sign, the light may blink on and then off. If you make a hard stop, the light may come on for a moment. This is normal. 3-32 (cid:127) (cid:127) {CAUTION: Do not keep driving if the oil pressure is low. If you do, your engine can become so hot that it catches ﬁre. You or others could be burned. Check your oil as soon as possible and have your vehicle serviced. Notice: Lack of proper engine oil maintenance may damage the engine. The repairs would not be covered by your warranty. Always follow the maintenance schedule in this manual for changing engine oil. Security Light This light ﬂashes when the vehicle security system is activated. Fog Lamp Light The fog lamps light will come on when the fog lamps are in use. The light will go out when the fog lamps are turned off. See Fog Lamps on page 3-15 for more information. Highbeam On Light This light will come on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 3-8. 3-33 Fuel Gage Boost Gage Your fuel gage tells you about how much fuel you have left. Here are four things that some owners ask about. None of these show a problem with your fuel gage: (cid:127) At the service station, the gas pump shuts off before the gage reads full. It takes a little more or less fuel to ﬁll up than the gage indicated. For example, the gage may have indicated the tank was half full, but it actually took a little more or less than half the tank’s capacity to ﬁll the tank. The gage moves a little when you turn a corner or speed up. The gage doesn’t go back to empty when you turn off the ignition. For your fuel tank capacity, see Capacities and Speciﬁcations on page 5-97. 3-34 United States Canada If your vehicle is equipped with this gage, it is located near the driver’s side of the instrument panel cluster. This gage indicates vacuum during light to moderate throttle and boost under heavier throttle. The gage displays the air pressure level going into the engine’s combustion chamber. The gage is automatically centered at zero every time the ignition is turned to RUN. Actual vacuum or boost is displayed from this zero point. Changes in ambient pressure, such as driving in mountains and changing weather, will slightly change the zero reading. (cid:127) (cid:127) (cid:127) Driver Information Center (DIC) The Driver Information Center (DIC) display gives you the status of many of your vehicle’s systems. The DIC is also used to display driver personalization menu modes and warning/status messages. All messages will appear in the DIC display, located at the bottom of the tachometer on the instrument panel cluster.

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2005 Chevrolet Cobalt Owners Manual