Login- Download PDF Manual
-
page 5‑42. Stop as soon as possible, and inflate the tires to the pressure value shown on the Tire and Loading Information label. See Tire Pressure on page 10‑50.
When the Light Flashes First and Then Is On Steady If the light flashes for about a minute and then stays on, there may be a problem with the TPMS. If the problem is not corrected, the light will come on at every ignition cycle. See Tire Pressure Monitor Operation on page 10‑53.
low can also damage the
Engine Oil Pressure Light Notice: Lack of proper engine oil maintenance can damage the engine. Driving with the engine oil engine. The repairs would not be covered by the vehicle warranty. Check the oil level as soon as possible. Add oil if required, but if the oil level is within the operating range and the oil pressure is still low, have the vehicle serviced. Always follow the maintenance schedule for changing engine oil.
The oil pressure light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer.
If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle could be low on oil and might have some other system problem. See your dealer.
Low Fuel Warning Light
This light is near the fuel gauge and comes on briefly when the ignition is turned on as a check to show it is working. It also comes on when the fuel tank is low on fuel. The light turns off when fuel is added. If it does not, have the vehicle serviced.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (24,1)
5-24
Instruments and Controls
Security Light
High-Beam On Light
Adaptive Forward Lighting (AFL) Light
The immobilizer light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off. If the light stays on and the engine does not start, there could be a problem with the theft-deterrent system. See Immobilizer Operation on page 2‑18.
This light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 6‑4. Automatic High-Beam Light
This light should come on briefly as the vehicle is started. If it does not come on, have the vehicle serviced by your dealer. This light comes on solid when there is a problem with the AFL system. It flashes when the system is switching between lighting modes. See Adaptive Forward Lighting (AFL) on page 6‑5.
This light comes on when the automatic high-beam headlamps are in use. See Exterior Lamp Controls on page 6‑1.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (25,1)
Lamps On Reminder
Cruise Control Light
Adaptive Cruise Control Light
Instruments and Controls
5-25
This light comes on when the exterior lamps are in use. See Exterior Lamp Controls on page 6‑1.
The cruise control light is white when the cruise control is on and ready, and turns green when the cruise control is set and active. See Cruise Control on page 9‑39.
This light in the Driver Information Center (DIC) comes on when the Adaptive Cruise Control (if equipped) is active. See Adaptive Cruise Control on page 9‑42.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (26,1)
5-26
Instruments and Controls
Information Displays
Driver Information Center (DIC) The DIC displays are shown in the left and right interactive display zones on the instrument cluster. The displays show the status of many vehicle systems. The controls for the DIC are on the right steering wheel control.
y or z : Press to move up or down in a list.
S or T : Press to move between the interactive display zones in the cluster. Press S to go back to the previous menu. SEL (Select): Press to open a menu or select a menu item. Press and hold to reset values on certain screens. DIC Information Display Options The information displays on the DIC can be turned on or off through the Settings menu. 1. Press SEL while viewing the
Settings page in the center display zone on the cluster.
2. Scroll to Info Pages and
press SEL.
3. Press y or z to move through
the list of possible information displays.
4. Press SEL while an item is
highlighted to select or deselect that item. When an item is selected, a checkmark will appear next to it.
DIC Information Displays The following is the list of all possible DIC information displays. Some of the information displays may not be available for your particular vehicle. Speed: The digital speedometer shows the vehicle speed in either kilometers per hour (km/h) or miles per hour (mph). Trip 1 and Trip 2: The Trip display shows the current distance traveled, in either kilometers (km) or miles (mi), since the trip odometer was last reset. The trip odometer can be reset by pressing and holding SEL while this display is active.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (27,1)
Instruments and Controls
5-27
Fuel Range: The Fuel Range display shows the approximate distance the vehicle can be driven without refueling. LOW will be displayed when the vehicle is low on fuel. The fuel range estimate is based on an average of the vehicle's fuel economy over recent driving history and the amount of fuel remaining in the fuel tank. Average Fuel Economy: The Average Fuel Economy display shows the approximate average liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number is calculated based on the number of L/100 km (mpg) recorded since the last time this menu item was reset. The Average Fuel Economy can be reset by pressing and holding SEL while this display is active.
Instantaneous Fuel Economy: The Instantaneous Fuel Economy display shows the current fuel economy in either liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number reflects only the fuel economy that the vehicle has right now and changes frequently as driving conditions change. Average Speed: The Average Speed display shows the average speed of the vehicle in kilometers per hour (km/h) or miles per hour (mph). This average is calculated based on the various vehicle speeds recorded since the last reset of this value. The average speed can be reset by pressing and holding SEL while this display is active.
Timer: This display can be used as a timer. To start the timer, press SEL while this display is active. The display will show the amount of time that has passed since the timer was last reset. To stop the timer, press SEL briefly while this display is active and the timer is running. To reset the timer to zero, press and hold SEL while this display is active. Compass: The Compass display shows the direction the vehicle is driving. Turn Arrow: The Turn Arrow display shows the next maneuver when using route guidance. Travel Time: The Travel Time display shows the estimated time duration remaining for the current route. Distance to Destination: The Distance to Destination display shows the distance to the destination when using route guidance.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (28,1)
5-28
Instruments and Controls
Speed Limit: The Speed Limit display shows the current speed limit. The information for this page comes from a roadway database. Speed Warning: The Speed Warning display allows the driver to set a speed that they do not want to exceed. To set the Speed Warning, press SEL when Speed Warning is displayed. Press y or z to adjust the value. This feature can be turned off by pressing and holding SEL while viewing this page. If the selected speed limit is exceeded, a pop-up warning is displayed and a chime may sound. Cruise Set Speed: The Cruise Set Speed display shows the speed the cruise control or Adaptive Cruise Control is set to. Battery Voltage: The Battery Voltage display shows the current battery voltage.
Oil Life: The Oil Life display shows an estimate of the oil's remaining useful life. If REMAINING OIL LIFE 99% is displayed, that means 99% of the current oil life remains. When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See Engine Oil Messages on page 5‑35. The oil should be changed as soon as possible. See Engine Oil on page 10‑11. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule. See Maintenance Schedule on page 11‑3. Remember, the Oil Life display must be reset after each oil change. It will not reset itself. Also, be careful not to reset the Oil Life display accidentally at any time other than when the oil has just been changed.
It cannot be reset accurately until the next oil change. To reset the engine oil life system, press and hold SEL for several seconds while the Oil Life display is active. See Engine Oil Life System on page 10‑13. Tire Pressure: The Tire Pressure display shows the approximate pressures of all four tires. Tire pressure is displayed in either kilopascal (kPa) or in pounds per square inch (psi). If the pressure is low, the value for that tire is shown in amber. See Tire Pressure Monitor System on page 10‑52 and Tire Pressure Monitor Operation on page 10‑53. Blank Page: The Blank Page display allows for no information to be displayed in the DIC display zone(s).
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (29,1)
Instruments and Controls
5-29
Notice: If you try to use the HUD image as a parking aid, you may misjudge the distance and damage your vehicle. Do not use the HUD image as a parking aid. The HUD information can be displayed in various languages. The speedometer reading and other numerical values can be displayed in either English or metric units. The language selection is changed through the radio and the units of measurement is changed through the instrument cluster. See Vehicle Personalization on page 5‑43 and “Settings” under Instrument Cluster on page 5‑9.
Head-Up Display (HUD)
{ WARNING
If the HUD image is too bright or too high in your field of view, it may take you more time to see things you need to see when it is dark outside. Be sure to keep the HUD image dim and placed low in your field of view.
For vehicles with HUD, some information concerning the operation of the vehicle is projected onto the windshield. This includes the speedometer reading, rpm reading, transmission position, compass heading, audio/phone information, and Turn-by-Turn Navigation information. The images are projected through the HUD lens on the driver side of the instrument panel.
HUD Display on the Vehicle
Windshield
The HUD information appears as an image focused out toward the front of the vehicle. The HUD may display different alerts and information for vehicles equipped with these features:
Traction Control System (TCS)
. StabiliTrak System . Collision Alert . Gap Adjust
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (30,1)
5-30
Instruments and Controls
. Upcoming Maneuver from
OnBoard Navigation
. Upcoming Maneuver from
OnStar Incoming Call
When the HUD is on, the speedometer reading is continually displayed, except when an imminent navigation maneuver is being shown. The current audio, phone, or navigation alert temporarily displays if their status changes. This occurs if the steering wheel controls are used to adjust a setting or acknowledge an alert.
The HUD control is to the left of the steering wheel.
To adjust the HUD image so that items are properly displayed: 1. Adjust the driver seat to a
comfortable position.
2. Start the engine. 3. Adjust the HUD controls. Use the following settings to adjust the HUD. $ (Image Adjustment): Press down or lift up to center the HUD image. The HUD image can only be adjusted up and down, not side to side. ! (Display View): Press to select the display view. Release when the desired display is shown on the HUD. If vehicle messages are displayed, pressing the DIC select button may clear the message. See Driver Information Center (DIC) on page 5‑26. D (Brightness): Lift up and hold to brighten the display. Press down and hold to dim the display. Hold down to turn the display off.
There are four views in the HUD display:
Metric
English
Speed View: This display gives the speedometer reading (in English or metric units), speed limit, Adaptive Cruise Control speed, Forward Collision Alert, Lane Departure Warning, and Vehicle Ahead indicator. Some information only appears on vehicles that have these features, and when they are active.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (31,1)
Instruments and Controls
5-31
closer you get to the maneuver. All navigation information is provided to the HUD by the navigation radio or OnStar (if equipped).
Metric
Metric
English
English
Audio/Phone View: This display includes the information in speed view along with audio/phone information. The current radio station, media type, and incoming calls will be displayed.
Navigation View: This display includes the information in speed view along with Turn-by-Turn Navigation information. The compass heading is displayed when navigation routing is not active. All formats will briefly show the Turn-by-Turn Navigation alerts and provide details about the next driving maneuver to be made. When you are near the next maneuver, the HUD displays a distance bar that will empty the
Metric
English
Performance View: This display gives the speedometer reading (in English or metric units), rpm reading, transmission positions, and gear shift indicator.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (32,1)
5-32
Instruments and Controls
The HUD image displayed on the windshield will automatically dim and brighten to compensate for outside lighting. However, the HUD brightness control can still be adjusted as needed. The HUD image can temporarily light up depending on the angle and position of the sunlight on the HUD display. This is normal and will change when the angle of the sunlight on the HUD display changes. Polarized sunglasses could make the HUD image harder to see. Care of the HUD Clean the inside of the windshield as needed to remove any dirt or film that could reduce the sharpness or clarity of the HUD image. To clean the HUD lens, use a soft, clean cloth that has household glass cleaner sprayed on it. Wipe the HUD lens gently, then dry it. Do not
spray cleaner directly on the lens because the cleaner could leak into the unit. If You Cannot See the HUD Image When the Ignition Is On
Is anything covering the HUD lens? Is the HUD dimmer setting bright enough? Is the HUD image adjusted to the proper height?
. Are you wearing polarized
sunglasses?
If the HUD Image Is Not Clear
Is the HUD image too bright? . Are the windshield and HUD
lens clean?
If the HUD image is not correct, contact your dealer. Keep in mind that the windshield is part of the HUD system. See Windshield Replacement on page 10‑30.
Vehicle Messages Messages displayed on the DIC indicate the status of the vehicle or some action that may be needed to correct a condition. Multiple messages may display one after the other. The messages that do not require immediate action can be acknowledged and cleared by pressing SEL. The messages that require immediate action cannot be cleared until that action is performed. All messages should be taken seriously and clearing the messages does not correct the problem. The following are some of the vehicle messages that may be displayed depending on the vehicle content.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (33,1)
Battery Voltage and Charging Messages
BATTERY SAVER ACTIVE This message displays when the vehicle has detected that the battery voltage is dropping beyond a reasonable point. The battery saver system starts reducing features of the vehicle that may be noticed. At the point that features are disabled, this message displays. Turn off unnecessary accessories to allow the battery to recharge. LOW BATTERY This message is displayed when the battery voltage is low. See Battery on page 10‑26. SERVICE BATTERY CHARGING SYSTEM This message is displayed when there is a fault in the battery charging system. Take the vehicle to your dealer for service.
Instruments and Controls
5-33
TRANSPORT MODE ON This message is displayed when the vehicle is in transport mode. Some features can be disabled while in this mode, including Remote Keyless Entry (RKE), remote start, and the vehicle alarm system. Take the vehicle to your dealer for service to turn transport mode off.
Brake System Messages
BRAKE FLUID LOW This message is displayed when the brake fluid level is low. See Brake Fluid on page 10‑25. STEP ON BRAKE TO RELEASE PARK BRAKE This message is displayed if you attempt to release the Electric Parking Brake without the brake pedal applied. See Parking Brake (Electric) on page 9‑30 or Parking Brake (Manual) on page 9‑33.
RELEASE PARKING BRAKE This message is displayed if the Electric Parking Brake is on while the vehicle is in motion. See Parking Brake (Electric) on page 9‑30 or Parking Brake (Manual) on page 9‑33. SERVICE BRAKE ASSIST This message may be displayed when there is a problem with the brake boost assist system. When this message is displayed, the brake boost assist motor might be heard operating and you might notice pulsation in the brake pedal. This is normal under these conditions. Take the vehicle to your dealer for service. SERVICE PARKING BRAKE This message is displayed when there is a problem with the parking brake. Take the vehicle to your dealer for service.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (34,1)
5-34
Instruments and Controls
Compass Messages Dashes may be displayed if the vehicle temporarily loses communication with the Global Positioning System (GPS).
Cruise Control Messages
ADAPTIVE CRUISE SET TO XXX This message displays when the Adaptive Cruise Control (ACC) speed is set. See Adaptive Cruise Control on page 9‑42. ADAPTIVE CRUISE TEMPORARILY UNAVAILABLE This message displays when attempting to activate Adaptive Cruise Control (ACC) when it is temporarily unavailable. The ACC system does not need service.
This can occur under the following conditions:
The radar is not clean. Keep the radar sensors free of mud, dirt, snow, ice, and slush. Clean the entire front and/or rear of the vehicle. For cleaning instructions, see Exterior Care on page 10‑81.
. Heavy rain or snow is interfering with the radar object detection or camera performance. CRUISE SET TO XXX This message displays when the cruise control speed is set. See Cruise Control on page 9‑39. NO CRUISE BRAKING GAS PEDAL APPLIED This message displays when Adaptive Cruise Control (ACC) is active and the driver is pressing the gas pedal. When this occurs, ACC will not brake. See Adaptive Cruise Control on page 9‑42.
Door Ajar Messages
DOOR OPEN A door open symbol will be displayed on the DIC showing which door is open. If the vehicle has been shifted out of P (Park), a DOOR OPEN message will also be displayed. If the vehicle is in manual shift mode, the DOOR OPEN message will be displayed if the vehicle starts to move. Close the door completely. HOOD OPEN This message will display along with a hood open symbol when the hood is open. Close the hood completely. TRUNK OPEN This message will display along with a symbol when the trunk is open. Close the trunk completely.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (35,1)
Instruments and Controls
5-35
Engine Cooling System Messages
A/C OFF ENGINE COOLANT HOT This message displays when the engine coolant becomes hotter than the normal operating temperature. To avoid added strain on a hot engine, the air conditioning compressor automatically turns off. When the coolant temperature returns to normal, the air conditioning compressor turns back on. The vehicle can continue to be driven. If this message continues to appear, have the system repaired by your dealer as soon as possible to avoid damage to the engine.
ENGINE OVERHEATED — IDLE ENGINE This message displays and a chime sounds when the engine coolant temperature is too hot. The engine coolant temperature warning light will also be on. Stop and allow the vehicle to idle until it cools down. ENGINE OVERHEATED — TURN VEHICLE OFF This message displays and a continuous chime sounds if the engine cooling system reaches unsafe temperatures for operation. The engine coolant temperature warning light will flash. Stop and turn off the vehicle as soon as it is safe to do so to avoid severe damage. This message clears when the engine has cooled to a safe operating temperature.
Engine Oil Messages
CHANGE ENGINE OIL SOON This message displays when the engine oil needs to be changed. When you change the engine oil, be sure to reset the Oil Life System. See Engine Oil Life System on page 10‑13, Driver Information Center (DIC) on page 5‑26, Engine Oil on page 10‑11, and Maintenance Schedule on page 11‑3. ENGINE OIL HOT, IDLE ENGINE This message displays when the engine oil temperature is too hot. Stop and allow the vehicle to idle until it cools down.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (36,1)
5-36
Instruments and Controls
ENGINE OIL LOW — ADD OIL On some vehicles, this message displays when the engine oil level may be too low. Check the oil level before filling to the recommended level. If the oil is not low and this message remains on, take the vehicle to your dealer for service. See Engine Oil on page 10‑11. OIL PRESSURE LOW — STOP ENGINE This message displays if low oil pressure levels occur. Stop the vehicle as soon as safely possible and do not operate it until the cause of the low oil pressure has been corrected. Check the oil as soon as possible and have the vehicle serviced by your dealer.
Engine Power Messages
ENGINE POWER IS REDUCED This message displays when the vehicle's engine power is reduced. Reduced engine power can affect the vehicle's ability to accelerate.
If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but maximum acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer for service as soon as possible.
Fuel System Messages
FUEL LEVEL LOW This message displays when the vehicle is low on fuel. Refuel as soon as possible TIGHTEN GAS CAP This message displays when the fuel cap is not on tight. Tighten the fuel cap.
Key and Lock Messages
NO REMOTE KEY WAS DETECTED PLACE KEY IN TRANSMITTER POCKET THEN START YOUR VEHICLE SEE OWNER’S MANUAL FOR DETAILS This message displays when trying to start the vehicle if an RKE transmitter is not detected. The transmitter battery may be weak. See “Starting the Vehicle with a Low Transmitter Battery” under Remote Keyless Entry (RKE) System Operation on page 2‑3. NO REMOTE PRESS BRAKE TO RESTART This message is displayed when attempting to turn off the vehicle and the remote is no longer detected. Restarting is allowed without the remote for five minutes. Press the brake pedal to restart the vehicle.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (37,1)
Instruments and Controls
5-37
NUMBER OF KEYS PROGRAMMED This message displays when programming new keys to the vehicle. REMOTE LEFT IN VEHICLE This message displays when leaving the vehicle with the RKE transmitter still inside. REPLACE BATTERY IN REMOTE KEY This message displays when the battery in the RKE transmitter needs to be replaced.
Lamp Messages
AFL (ADAPTIVE FORWARD LIGHTING) LAMPS NEED SERVICE This message displays when the AFL system is disabled and needs service. See your dealer. See Adaptive Forward Lighting (AFL) on page 6‑5. AUTOMATIC LIGHT CONTROL ON/OFF This message is displayed when the exterior lamp control is in AUTO and the lights have turned on or off. See Automatic Headlamp System on page 6‑5.
XXX TURN INDICATOR FAILURE When one of the turn signals is out, this message displays to show which bulb needs to be replaced. See Bulb Replacement on page 10‑31 and Replacement Bulbs on page 10‑33. TURN SIGNAL ON This message is displayed if the turn signal has been left on. Turn off the turn signal.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (38,1)
5-38
Instruments and Controls
Object Detection System Messages
24 GHz RADARS OFF This message displays when driving in certain areas where there may be radar interference. Adaptive Cruise Control (ACC), Forward Collision Alert (FCA), and the Active Emergency Braking System may not work or may not work as well. The vehicle does not need service. AUTOMATIC COLLISION PREP UNAVAILABLE This message displays when the Active Emergency Braking System has been unavailable for some time. The Active Emergency Braking System does not need service.
This can occur under the following conditions:
The radar is not clean. Keep the radar sensors free of mud, dirt, snow, ice, and slush. Clean the entire front and/or rear of the vehicle. For cleaning instructions, see Exterior Care on page 10‑81.
. Heavy rain or snow is interfering with the radar object detection or camera performance.
This message may also be displayed if there is a problem with the StabiliTrak system. FORWARD COLLISION ALERT OFF This message displays when the Forward Collision Alert has been turned off.
FRONT CAMERA BLOCKED CLEAN WINDSHIELD This message displays when the camera is blocked. Cleaning the outside of the windshield behind the rearview mirror may correct the issue. The Lane Departure Warning system will not operate. Forward Collision Alert (FCA) may not work or may not work as well. LANE DEPARTURE WARNING UNAVAILABLE This message displays when attempting to activate the Lane Departure Warning (LDW) system when it is temporarily unavailable. The LDW system does not need service. This message could be due to the camera being blocked. Cleaning the outside of the windshield behind the rearview mirror may correct the issue.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (39,1)
Instruments and Controls
5-39
PARK ASSIST OFF This message displays when the Parking Assist system has been turned off or when there is a temporary condition causing the system to be disabled. REAR AUTO BRAKE AND PARK ASSIST UNAVAILABLE This message displays when attempting to activate the parking and backing features of the Driver Assistance System when they are temporarily unavailable. The system does not need service. This can occur under the following conditions:
The radar is not clean. Keep the radar sensors free of mud, dirt, snow, ice, and slush. Clean the entire front and/or rear of the vehicle. For cleaning instructions, see Exterior Care on page 10‑81.
. Heavy rain or snow is interfering with the radar object detection or camera performance.
See Driver Assistance Systems on page 9‑50. SERVICE AUTOMATIC COLLISION PREP If this message displays, take the vehicle to your dealer to repair the system. SERVICE DRIVER ASSIST SYSTEM If this message displays, take the vehicle to your dealer to repair the system. Adaptive Cruise Control (ACC), Forward Collision Alert (FCA), Active Emergency Braking System, Assistance Systems for Parking or Backing, and/or Lane Departure Warning (LDW) system may not work. Do not use these systems until the vehicle has been repaired.
SERVICE FRONT CAMERA If this message remains on after continued driving, the vehicle needs service. Do not use the Lane Departure Warning (LDW) and Forward Collision Alert (FCA) features. Take the vehicle to your dealer. SERVICE PARK ASSIST This message displays if there is a problem with the Parking Assist system. Do not use this system to help you park. See your dealer for service. SERVICE REAR AUTO BRAKE AND PARK ASSIST This message displays if there is a problem with the parking and backing features of the Driver Assistance System. Do not use this system to help park or back the vehicle. See your dealer for service.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (40,1)
5-40
Instruments and Controls
SIDE BLIND ZONE ALERT OFF This message indicates that the driver has turned the Side Blind Zone Alert (SBZA) system off. SERVICE SIDE DETECTION SYSTEM If this message remains on after continued driving, the vehicle needs service. Side Blind Zone Alert (SBZA) and Rear Cross Traffic Alert (RCTA) features will not work. Take the vehicle to your dealer. SIDE DETECTION SYSTEM UNAVAILABLE This message indicates that Side Blind Zone Alert (SBZA) and Rear Cross Traffic Alert (RCTA) are disabled either because the sensor is blocked and cannot detect vehicles in the blind zone, or the vehicle is passing through an open area, such as the desert, where there is insufficient data for operation. This message may also activate during heavy rain or due to road spray. The vehicle does not
need service. For cleaning, see "Washing the Vehicle" under Exterior Care on page 10‑81.
Ride Control System Messages
ALL WHEEL DRIVE OFF If the vehicle has the All-Wheel-Drive (AWD) system, this message displays when there is a temporary condition making the AWD system unavailable. The vehicle will run in 2WD. This could be caused by:
Loss of wheel or vehicle speed
. AWD system overheat . Certain vehicle electrical
conditions
This message turns off when the above conditions are no longer present and the warning message is reset. See All-Wheel Drive on page 9‑29.
SERVICE ALL WHEEL DRIVE This message displays if a problem occurs with the All-Wheel-Drive (AWD) system. The vehicle will run in 2WD. This could be caused by: . An electronics problem . Worn out or overheated clutch
plates
. Various electrical issues The system may need service. See your dealer. SERVICE STABILITRAK This message displays if there is a problem with the StabiliTrak system. See StabiliTrak® System on page 9‑36. SERVICE SUSPENSION SYSTEM This message displays when there is a problem with the MagneRide™ system. See Driver Mode Control on page 9‑37. Have the vehicle serviced by your dealer.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (41,1)
Instruments and Controls
5-41
SERVICE TRACTION CONTROL This message displays when there is a problem with the Traction Control System (TCS). See Traction Control System (TCS) on page 9‑34. TRACTION CONTROL OFF This message may display when the Traction Control System (TCS) has been turned off. See Traction Control System (TCS) on page 9‑34
TRACTION CONTROL ON This message may display when the Traction Control System (TCS) has been turned on. See Traction Control System (TCS) on page 9‑34Airbag System Messages
SERVICE AIRBAG This message displays if there is a problem with the airbag system. Take the vehicle to your dealer for service.
Security Messages
THEFT ATTEMPTED This message displays if the vehicle detects a tamper condition.
Service Vehicle Messages
SERVICE AC SYSTEM This message displays if there is a problem with the air conditioning system. Take the vehicle to your dealer for service. SERVICE POWER STEERING This message displays if there is a problem with the power steering system. Take the vehicle to your dealer for service. SERVICE STEERING COLUMN LOCK This message displays if there is a problem with the steering column lock. Take the vehicle to your dealer for service.
SERVICE VEHICLE SOON This message displays if there is a problem with the vehicle. Take the vehicle to your dealer for service.
Starting the Vehicle Messages
PRESS BRAKE TO START VEHICLE This message is displayed when attempting to start the vehicle without first pressing the brake pedal. SERVICE KEYLESS START SYSTEM This message is displayed if there is a problem with the pushbutton start system. Take the vehicle to your dealer for service.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (42,1)
5-42
Instruments and Controls
TURN STEERING WHEEL START VEHICLE AGAIN This message may display when you try to start the vehicle, but the column remains locked. Try turning the steering wheel while starting the vehicle to unlock the steering column. If the vehicle still does not start, turn the steering wheel the other way, and try starting the vehicle again.
Tire Messages
SERVICE TIRE MONITOR SYSTEM This message displays if there is a problem with the Tire Pressure Monitor System (TPMS). See Tire Pressure Monitor Operation on page 10‑53. TIRE LEARNING ACTIVE This message displays when the system is learning new tires. See Tire Pressure Monitor Operation on page 10‑53.
TIRE LOW ADD AIR TO TIRE This message displays when the pressure in one or more of the tires is low. This message also displays LEFT FRONT, RIGHT FRONT, LEFT REAR, or RIGHT REAR to indicate the location of the low tire. The low tire pressure warning light will also come on. See Tire Pressure Light on page 5‑22. If a tire pressure message appears on the DIC, stop as soon as you can. Inflate the tires by adding air until the tire pressure is equal to the values shown on the Tire and Loading Information label. See Tires on page 10‑42, Vehicle Load Limits on page 9‑11, and Tire Pressure on page 10‑50. You can receive more than one tire pressure message at a time. The DIC also shows the tire pressure values. See Driver Information Center (DIC) on page 5‑26.
Transmission Messages
SERVICE TRANSMISSION This message displays if there is a problem with the transmission. See your dealer. SHIFT DENIED This message displays when using the Driver Shift Control (DSC) and attempting to shift to a gear not appropriate for the vehicle speed and engine revolutions per minute (rpm). See Manual Mode on page 9‑26. SHIFT TO PARK This message displays when the transmission needs to be shifted to P (Park). This may appear when attempting to remove the key from the vehicle if the vehicle is not in P (Park).
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (43,1)
TRANSMISSION HOT — IDLE ENGINE This message displays and a chime sounds if the transmission fluid in the vehicle gets hot. Driving with the transmission fluid temperature high can cause damage to the vehicle. Stop the vehicle and let it idle to allow the transmission to cool. This message clears when the fluid temperature reaches a safe level.
Vehicle Reminder Messages
ICE POSSIBLE DRIVE WITH CARE This message displays when ice conditions are possible.
Instruments and Controls
5-43
Vehicle Speed Messages
SELECTED SPEED LIMIT EXCEEDED This message is displayed when the vehicle speed is greater than the set speed. See "Speed Warning" under Driver Information Center (DIC) on page 5‑26. VEHICLE SPEED LIMITED This message is displayed under certain conditions when there is a problem and the vehicle’s speed is being limited.
Washer Fluid Messages
WASHER FLUID LOW ADD FLUID This message may display when the washer fluid level is low. See Washer Fluid on page 10‑23.
Vehicle Personalization The audio system controls are used to access the personalization menus for customizing vehicle features.
Base Radio Audio System Controls MENU: Press the center of the knob to enter the menus and select menu items. Turn the knob to scroll through the menus. S BACK: Press to exit or move backward in a menu. To access the personalization menu: 1. On the Home page, turn the
MENU knob to highlight Settings and press the MENU knob.
2. Turn the MENU knob to highlight
Vehicle Settings and press the MENU knob.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (44,1)
5-44
Instruments and Controls
CUE Infotainment System Audio System Controls To access the personalization menu: 1. Press SETTINGS on the Home
page on the infotainment system display.
2. Press Vehicle Settings. 3. Press the desired feature to
display a list of available options.
4. Press to select the desired
feature setting.
5. Press the 0 to return to the
previous menu.
Personalization Menus The following list of menu items may be available: . Climate and Air Quality . Collision/Detection Systems . Comfort and Convenience
Language Lighting
. Power Door Locks . Remote Locking, Unlocking,
Starting
. Return to Factory Settings Climate and Air Quality Select the Climate and Air Quality menu and the following may be displayed: . Auto Fan Max Speed . Auto Defog . Auto Rear Defog
Auto Fan Max Speed This feature will set the maximum auto fan speed. Select Low, Medium, or High.
Auto Defog This will turn auto defog on or off. Only vehicles with the uplevel dual automatic climate control system will have this option. Select Off or On.
Auto Rear Defog If equipped, this will turn auto rear defog on or off. This feature will automatically turn on the rear window defogger when it is cold outside. Select Off or On. Collision/Detection Systems Select the Collision/Detection Systems menu and the following will be displayed (if equipped): . Alert Type . Auto Collision Preparation . Park Assist . Go Notifier . Side Blind Zone Alert
Alert Type This feature will set crash alerts to beeps or seat vibrations. This setting affects all crash alerts including Forward Collision,
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (45,1)
Instruments and Controls
5-45
Lane Departure Warning, Adaptive Cruise Control, Parking Assist, and Backing Warning alerts. Select Beeps or Safety Alert Seat.
Auto Collision Preparation feature. See Active Emergency Braking System on page 9‑58. Select Off, Alert & Brake, or Alert.
Auto Collision Preparation This feature will turn on or off the Forward Collision Alert feature as well as the Automatic Braking capability of the Auto Collision Preparation feature. With the Alert & Brake setting, both Forward Collision Alert as well as the Automatic Braking capability of the Auto Collision Preparation feature are available. The Alert setting disables most automatic braking functions of the Auto Collision Preparation feature. Some last-second automatic braking capability is still provided with the Alert setting, but it is much less likely to be triggered by most driving conditions. Off disables all Forward Collision Alert and Automatic Braking capabilities of the
Park Assist This allows the Ultrasonic Parking Assist feature to be turned on or off. Select Off or On.
Go Notifier This feature will give a reminder that Adaptive Cruise Control provides when it has brought the vehicle to a complete stop behind another stopping vehicle, and then that vehicle drives on. Select Off or On.
Side Blind Zone Alert This allows the Side Blind Zone Alert feature to be turned on or off. Select Off or On.
Comfort and Convenience Select the Comfort and Convenience menu and the following will be displayed: . Auto Memory Recall . Reverse Tilt Mirror . Easy Exit Options . Chime Volume . Personalization by Driver . Rain Sense Wipers
Auto Memory Recall This allows the Auto Memory Recall feature to be turned on or off. Select Off or On. On some vehicles select Off, On - Driver Door Open, or On - At ignition On.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (46,1)
5-46
Instruments and Controls
Rain Sense Wipers This allows the Rain Sense Wipers feature to be turned on or off. Select Disabled or Enabled. Language Select the Language menu and the following will be displayed: . English French . Spanish Select the language. The selected language will display on the system, and voice recognition will reflect the selected language.
Reverse Tilt Mirror When on, both the driver and passenger, driver, or passenger mirrors will tilt downward when the vehicle is shifted to R (Reverse) to improve visibility of the ground near the rear wheels. They will return to their previous driving position when the vehicle is shifted out of R (Reverse) or the ignition is turned to OFF. Select Off, On - Driver and Passenger, On - Driver, or On - Passenger.
Easy Exit Options This allows the Easy Exit Options feature to be turned on or off. Select Off or On.
Chime Volume This allows the selection of the chime volume level. Select a volume between 0 and 63.
Lighting Select the Lighting menu and the following will be displayed: . Vehicle Locator Lights . Exit Lighting
Left or Right Hand Traffic
. Auto High Beam . Adaptive High Beam . Adaptive Forward Lighting . Daytime Tail Lights
Vehicle Locator Lights This allows the vehicle locator lights to be turned on or off. Select Off or On.
Exit Lighting This allows the selection of how long the exterior lamps stay on when leaving the vehicle when it is dark outside. Select Off, 30 Seconds, 60 Seconds, or 120 Seconds.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (47,1)
Left or Right Hand Traffic This allows the selection to change the vehicle for left hand or right hand traffic. Select Left Hand Traffic or Right Hand Traffic. On some vehicles select Left Hand Traffic, Right Hand Traffic, or Automatic (GPS).
Auto High Beam This allows the Auto High Beam to be turned on or off. Select Off or On. On some vehicles select Off, Normal Sensitivity, or Low Sensitivity.
Adaptive High Beam This allows the vehicle locator lights to be turned on or off. Select Off or On. On some vehicles elect Off, Normal Sensitivity, or Low Sensitivity.
Instruments and Controls
5-47
Adaptive Forward Lighting This allows the selection of how long the exterior lamps stay on when leaving the vehicle when it is dark outside. Select Corner and Curve Lighting or Intelligent Light Distribution. On some vehicles select Corner and Curve Lighting, Intelligent Light Distribution, or GPS Assistance.
Daytime Tail Lights This allows the Daytime Tail Lights to be turned on or off. Select Off or On. Power Door Locks Select Power Door Locks and the following will be displayed: . Unlocked Door Anti Lock Out . Auto Door Lock . Auto Door Unlock . Delayed Door Lock
Unlocked Door Anti Lock Out When on, this feature will keep the driver door from locking when the door is open. If Off is selected, the Delayed Door Lock menu will be available. Select Off or On.
Auto Door Lock This allows selection of which of the doors will automatically lock when the vehicle is shifted out of P (Park) (automatic transmission) or at 13 km/h (8 mph) (manual transmission). Select Off or On.
Auto Door Unlock This allows selection of which of the doors will automatically unlock when the vehicle is shifted into P (Park) (automatic transmission) or when the key is removed from the ignition (manual transmission). Select Off, All Doors, or Driver Door.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (48,1)
5-48
Instruments and Controls
Delayed Door Lock When on, this feature will delay the locking of the doors. To override the delay, press the power door lock switch on the doors. Select Off or On. Remote Lock, Unlock, and Start Select Remote Lock/Unlock and the following may be displayed: . Remote Unlock Light Feedback . Remote Lock Feedback . Remote Door Unlock . Relock Remotely Unlocked
Doors
. Remote Start . Remote Start Auto Heat Seats . Passive Door Unlock . Passive Door Lock . Remote Left in Vehicle Reminder
Remote Unlock Light Feedback When on, the exterior lamps will flash when unlocking the vehicle with the RKE transmitter. Select Off or Flash Lights.
Remote Lock Feedback This allows selection of what type of feedback is given when locking the vehicle with the RKE transmitter. Select Off, Lights and Horn, Lights Only, or Horn Only.
Remote Door Unlock This allows selection of which doors will unlock when pressing the unlock button on the RKE transmitter. Select All Doors or Driver Door Only.
Relock Remotely Unlocked Doors When on, if the doors are unlocked from the RKE transmitter and a door is not opened, the doors will automatically relock. Select Off or On.
Remote Start This allows the remote start feature to be turned on or off. Select Off or On.
Remote Start Auto Heat Seats If equipped and turned on, this feature will turn the heated seats on when using remote start on cold days. Select Off or On. On some vehicles select Off, On - Driver and Passenger, or On - Driver.
Passive Door Unlock This allows passive unlocking to be turned on or off and selects what doors will unlock. Select All Doors or Driver Door Only.
Passive Door Lock This allows passive locking to be turned on or off and selects feedback.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (49,1)
Instruments and Controls
5-49
Select On, On with Horn Chirp, or Off.
Remote Left in Vehicle Reminder This allows the remote left in vehicle feature to be turned on or off. Select Off or On. Return to Factory Settings Select Return to Factory Settings and the following list may display: . Restore Vehicle Settings . Clear All Private Data . Restore Radio Settings
Restore Vehicle Settings This allows selection of restoring vehicle settings. Select Cancel or Continue.
Clear All Private Data This allows selection to clear all private information from the vehicle. Select Cancel or Continue.
Restore Radio Settings This allows selection to restore radio settings. Select Cancel or Continue.
Universal Remote System See Radio Frequency Statement on page 13‑21 for information regarding Part 15 of the Federal Communications Commission (FCC) rules and Industry Canada Standards RSS-GEN/210/220/310.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (50,1)
5-50
Instruments and Controls
Universal Remote System Programming
If the vehicle has this feature, you will see these buttons with one indicator light next to them in the overhead console. This system provides a way to replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home automation devices.
Do not use the Universal Remote system with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1,1982. Read the instructions completely before attempting to program the Universal Remote system. Because of the steps involved, it may be helpful to have another person available to assist with programming the Universal Remote system. Keep the original hand-held transmitter for use in other vehicles as well as for future Universal Remote system programming. It is also recommended that upon the sale of the vehicle, the programmed Universal Remote system buttons be erased for security purposes. See “Erasing Universal Remote System Buttons” later in this section.
When programming a garage door, park outside of the garage. Park directly in line with and facing the garage door opener motor-head or gate motor-head. Be sure that people and objects are clear of the garage door or gate being programmed. It is recommended that a new battery be installed in the hand-held transmitter for quicker and more accurate transmission of the radio-frequency signal. Programming the Universal Remote System For questions or help programming the Universal Remote system, call 1-800-355-3515 or go to www.homelink.com. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before starting. Otherwise, the device will time out and the procedure will have to be repeated.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (51,1)
Instruments and Controls
5-51
To program up to three devices: 1. Hold the end of the hand-held
transmitter about 3 to 8 cm (1 to 3 in) away from the Universal Remote system buttons while keeping the indicator light in view. The hand-held transmitter was supplied by the manufacturer of the garage door opener receiver (motor-head unit).
2. At the same time, press and
hold both the hand-held transmitter button and one of the three Universal Remote system buttons to be used to operate the garage door. Do not release the Universal Remote system button or the hand-held transmitter button until the indicator light changes from a slowly to a rapidly flashing light. You now may release both buttons.
Some entry gates and garage door openers may require substitution of Step 2 with the procedure noted in “Gate Operator and Canadian Programming” later in this section.
3. Press and hold for five seconds
the newly trained Universal Remote system button (the button selected in Step 2) while observing the indicator light and garage door activation.
If the indicator light stays on continuously or the garage door starts to move when the Universal Remote system button is pressed and released, then the programming is complete. There is no need to continue programming Steps 4–6.
If the Universal Remote system indicator light blinks rapidly for two seconds, then turns to a constant light and the garage door does not move, continue with programming Steps 4–6. It may be helpful to have another person assist with the remaining Steps 4–6.
“Learn” or “Smart” Button
4. After Steps 1–3 have been
completed, locate the “Learn” or “Smart” button inside the garage on the garage door opener receiver (motor-head unit). The name and color of the button may vary by manufacturer.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (52,1)
5-52
Instruments and Controls
5. Firmly press and release the
6.
“Learn” or “Smart” button. After pressing this button, you will have 30 seconds to complete Step 6. Immediately return to the vehicle. Firmly press and hold for two seconds the Universal Remote system button, selected in Step 2 to control the garage door, and then release it. If the garage door does not move or the lamp on the garage door opener receiver (motor-head unit) does not flash, press and hold the same button a second time for two seconds, then release it. Again, if the door does not move or the garage door lamp does not flash, press and hold the same button a third time for two seconds, then release.
The Universal Remote system should now activate the garage door.
To program the remaining two Universal Remote system buttons, begin with Step 1 of “Programming the Universal Remote System.” Gate Operator and Canadian Programming If you have questions or need help programming the Universal Remote system, call 1-800-355-3515 or go to www.homelink.com. Canadian radio-frequency laws require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for the Universal Remote system to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to time out in the same manner. If you live in Canada, or you are having difficulty programming a gate operator or garage door opener by using the “Programming the Universal Remote System” procedures, regardless of where
you live, replace Step 2 under “Programming the Universal Remote System” with the following: Continue to press and hold the Universal Remote system button while you press and release every two seconds (cycle) the hand-held transmitter button until the frequency signal has been successfully accepted by the Universal Remote system. The Universal Remote system indicator light will flash slowly at first and then rapidly. Proceed with Step 3 under “Programming the Universal Remote System” to complete.
Universal Remote System Operation
Using the Universal Remote System Press and hold the appropriate Universal Remote system button for at least half of a second. The indicator light will come on while the signal is being transmitted.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (53,1)
Instruments and Controls
5-53
Erasing Universal Remote System Buttons All programmed buttons should be erased when the vehicle is sold or the lease ends. To erase all programmed buttons on the Universal Remote system device: 1. Press and hold down the two
outside buttons until the indicator light begins to flash. This should take about 10 seconds.
2. Release both buttons.
Reprogramming a Single Universal Remote System Button To reprogram any of the three Universal Remote system buttons: 1. Press and hold the desired
Universal Remote system button. Do not release the button.
2. The indicator light will begin to flash after 20 seconds. Without releasing the button, proceed with Step 1 under “Programming the Universal Remote System.”
If you have questions or need help programming the Universal Remote system, call 1-800-355-3515 or go to www.homelink.com. You may also call the customer assistance phone number under Customer Assistance Offices (U.S. and Canada) on page 13‑4 or Customer Assistance Offices (Mexico) on page 13‑5.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (54,1)
5-54
Instruments and Controls
2 NOTES
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (1,1)
Lighting
Exterior Lighting
Exterior Lamp Controls . . . . . . . . 6-1
Exterior Lamps OffReminder . . . . . . . . . . . . . . . . . . . . 6-4
Headlamp High/Low-Beam
Changer . . . . . . . . . . . . . . . . . . . . . 6-4
Flash-to-Pass . . . . . . . . . . . . . . . . . 6-4
Daytime RunningLamps (DRL) . . . . . . . . . . . . . . . . 6-4
Automatic Headlamp
System . . . . . . . . . . . . . . . . . . . . . . 6-5
Adaptive Forward
Lighting (AFL) . . . . . . . . . . . . . . . 6-5
Hazard Warning Flashers . . . . . 6-6
Turn and Lane-ChangeSignals . . . . . . . . . . . . . . . . . . . . . . 6-6
Interior Lighting
Instrument Panel Illumination
Control . . . . . . . . . . . . . . . . . . . . . . 6-7
Courtesy Lamps . . . . . . . . . . . . . . 6-7
Dome Lamps . . . . . . . . . . . . . . . . . 6-7
Reading Lamps . . . . . . . . . . . . . . . 6-7Lighting Features
Entry Lighting . . . . . . . . . . . . . . . . . 6-8
Exit Lighting . . . . . . . . . . . . . . . . . . . 6-8
Battery Power Protection . . . . . . 6-8
Exterior Lighting BatterySaver . . . . . . . . . . . . . . . . . . . . . . . . 6-8
Lighting
6-1
Exterior Lighting
Exterior Lamp Controls
The exterior lamp control is on the turn and lane change lever. Turn the control to the following positions: O (Off): Turns off the exterior lamps. The knob returns to the AUTO position after it is released. Turn to O again to reactivate the AUTO mode.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (2,1)
6-2
Lighting
In Canada, the headlamps will automatically reactivate when the vehicle is shifted out of P (Park) on automatic transmission vehicles, and when the parking brake is released on manual transmission vehicles. AUTO (Automatic): Automatically turns the exterior lamps on and off, depending on outside lighting. ; (Parking Lamps): Turns on the parking lamps together with the following: . Sidemarker Lamps
Taillamps License Plate Lamps Instrument Panel Lights
2 (Headlamps): Turns on the headlamps together with the following: . Sidemarker Lamps
Taillamps License Plate Lamps
Instrument Panel Lights
. Parking Lamps Automatic High-Beam System This system turns the vehicle's high-beam headlamps on and off according to surrounding traffic conditions. The system turns the high-beam headlamps on when it is dark enough and there is no other traffic present.
This light comes on in the instrument cluster when the automatic high-beam system is enabled.
Turning On and Enabling Automatic High Beams To enable the automatic high-beam system, with the turn and lane-change lever in the neutral position, turn the exterior lamp control to AUTO. The blue high-beam on light appears on the instrument cluster when the high beams are on.
Driving with Automatic High Beams The system only activates the high beams when driving over 40 km/h (25 mph). There is a sensor near the top center of the windshield, which automatically controls the system. Keep this area of the windshield clear of debris to allow for best system performance.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (3,1)
Lighting
6-3
. Your vehicle's windshield is dirty,
cracked, or obstructed by something that blocks the view of the light sensor.
. Your vehicle's windshield is covered with ice, dirt, haze, or other obstructions.
. Your vehicle is loaded such that
the front end points upward, causing the light sensor to aim high and not detect headlamps and taillamps.
. You are driving on winding or
hilly roads.
You may need to manually disable or cancel the high-beam headlamps
