Download PDF Manual

(GMNA-Localizing-U.S./Canada/Mexico-


Lower Anchors


Top Tether Anchor


Lower anchors (1) are metal bars built into the vehicle. There are two lower anchors for each LATCH seating position that will accommodate a child restraint with lower attachments (2).


A top tether (3, 4) anchors the top of the child restraint to the vehicle. A top tether anchor is built into the vehicle. The top tether attachment (2) on the child restraint connects to the top tether anchor in the vehicle in order to reduce the forward movement and rotation of the child restraint during driving or in a crash. The child restraint may have a single tether (3) or a dual tether (4). Either will have a single attachment (2) to secure the top tether to the anchor.


Seats and Restraints


81


Some child restraints that have a top tether are designed for use with or without the top tether being attached. Others require the top tether always to be attached. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached. Be sure to read and follow the instructions for the child restraint. Lower Anchor and Top Tether Anchor Locations


Rear Seat


I (Top Tether Anchor) : Seating positions with top tether anchors.


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


82


Seats and Restraints


H (Lower Anchor) : Seating positions with two lower anchors.


To assist you in locating the lower anchors, each rear anchor position has a label, near the crease between the seatback and the seat cushion.


To assist in locating the top tether anchors, the top tether anchor symbol is on the cover.


The top tether anchors are under the covers, behind the rear seat, on the filler panel. Be sure to use an anchor on the same side of the vehicle as the seating position where the child restraint will be placed. Do not secure a child restraint in a position without a top tether anchor if a national or local law requires that the top tether be attached, or if the instructions that come with the child restraint say that the top tether must be attached. According to accident statistics, children and infants are safer when properly restrained in a child


restraint system or infant restraint system secured in a rear seating position. See Where to Put the Restraint 0 79 for additional information. Securing a Child Restraint Designed for the LATCH System


{ Warning


If a LATCH-type child restraint is not attached to anchors or with the safety belt, the child restraint will not be able to protect the child correctly. In a crash, the child could be seriously injured or killed. Install a LATCH-type child restraint properly using the anchors, or use the vehicle safety belts to secure the restraint, following the instructions that came with the child restraint and the instructions in this manual.


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


{ Warning


To reduce the risk of serious or fatal injuries during a crash, do not attach more than one child restraint to a single anchor. Attaching more than one child restraint to a single anchor could cause the anchor or attachment to come loose or even break during a crash. A child or others could be injured.


{ Warning


Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck. The shoulder belt can tighten but cannot be loosened if it is locked. The shoulder belt locks when it is pulled all the way out of the retractor. It unlocks when the shoulder belt is allowed to go all the way back into the retractor, but it cannot do this if it is


(Continued)


Seats and Restraints


83


Warning (Continued)


Caution (Continued)


wrapped around a child’s neck. If the shoulder belt is locked and tightened around a child’s neck, the only way to loosen the belt is to cut it. Buckle any unused safety belts behind the child restraint so children cannot reach them. Pull the shoulder belt all the way out of the retractor to set the lock, and tighten the belt behind the child restraint after the child restraint has been installed.


Caution


Do not let the LATCH attachments rub against the vehicle’s safety belts. This may damage these parts. If necessary, move buckled safety belts to avoid rubbing the LATCH attachments.


(Continued)


Do not fold the empty rear seat with a safety belt buckled. This could damage the safety belt or the seat. Unbuckle and return the safety belt to its stowed position, before folding the seat.


If you need to secure more than one child restraint in the rear seat, see Where to Put the Restraint 0 79. This system is designed to make installation of child restraints easier. When using lower anchors, do not use the vehicle's safety belts. Instead use the vehicle's anchors and child restraint attachments to secure the restraints. Some restraints also use another vehicle anchor to secure a top tether. 1. Attach and tighten the lower


attachments to the lower anchors. If the child restraint does not have lower attachments or the desired seating position does not have lower anchors, secure the child


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


84


Seats and Restraints


restraint with the top tether and the safety belts. Refer to the child restraint manufacturer instructions and the instructions in this manual. 1.1. Find the lower anchors for the desired rear outboard seating position.


1.2. Put the child restraint on


the seat. For outboard rear seating positions, if the head restraint interferes with the proper installation of the child restraint, the head restraint may be removed. See “Head Restraint Removal and Reinstallation” at the end of this section.


1.3. Attach and tighten the


lower attachments on the child restraint to the lower anchors.


2.


If the child restraint manufacturer recommends that the top tether be attached, attach and tighten the top


tether to the top tether anchor, if equipped. Refer to the child restraint instructions and the following steps: 2.1. Find the top tether anchor.


Open the top tether anchor cover to expose the anchor.


2.2. Route, attach, and tighten the top tether according to the child restraint instructions and the following instructions:


If you are using a single tether in a rear outboard seating position with an adjustable head restraint, raise the head restraint and route the single tether


under the head restraint and in between the head restraint posts.


If you are using a dual tether in a rear outboard seating position with an adjustable head restraint, raise the head restraint and route the tether under the head restraint and around the head restraint posts.


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


head restraint has been removed, route the dual tether over the seatback.


If you are using a single tether in the rear center seating position, route the single tether over the headrest.


Seats and Restraints


85


If you are using a dual tether in the rear center seating position, route the dual tether over the headrest.


3. Before placing a child in the


child restraint, make sure it is securely held in place. To check, grasp the child restraint at the LATCH path and attempt to move it side to side and back and forth. There should be no more than 2.5 cm (1 in) of movement, for proper installation.


Head Restraint Removal and Reinstallation The rear outboard head restraints can be removed if they interfere with the proper installation of the child restraint. To remove the head restraint: 1. Partially fold the seatback


forward. See Rear Seats 0 53
for additional information.


If you are using a single tether in a rear outboard seating position and the head restraint has been removed, route the single tether over the seatback.


If you are using a dual tether in a rear outboard seating position and the


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


86


Seats and Restraints


{ Warning


With head restraints that are not installed and adjusted properly, there is a greater chance that occupants will suffer a neck/ spinal injury in a crash. Do not drive until the head restraints for all occupants are installed and adjusted properly.


2. Press both buttons on the head


To reinstall the head restraint:


restraint posts at the same time, and pull up on the head restraint.


3. Store the head restraint in the


trunk of the vehicle.


4. When the child restraint is removed, reinstall the head restraint before the seating position is used.


1.


Insert the head restraint posts into the holes in the top of the seatback. The notches on the posts must face the driver side of the vehicle.


2. Push the head restraint down. If necessary, press the height adjustment release button to further lower the head restraint. See Head Restraints 0 48.


3. Try to move the head restraint to make sure that it is locked in place.


Replacing LATCH System Parts After a Crash { Warning


A crash can damage the LATCH system in the vehicle. A damaged LATCH system may not properly secure the child restraint, resulting in serious injury or even death in a crash. To help make sure the LATCH system is working properly after a crash,


(Continued)


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


Warning (Continued)


see your dealer to have the system inspected and any necessary replacements made as soon as possible.


If the vehicle has the LATCH system and it was being used during a crash, new LATCH system parts may be needed. New parts and repairs may be necessary even if the LATCH system was not being used at the time of the crash.


Securing Child Restraints (Rear Seat) When securing a child restraint in a rear seating position, study the instructions that came with the child restraint to make sure it is compatible with this vehicle. If the child restraint has the LATCH system, see Lower Anchors and Tethers for Children (LATCH System) 0 80 for how and where to


install the child restraint using LATCH. If a child restraint is secured in the vehicle using a safety belt and it uses a top tether, see Lower Anchors and Tethers for Children (LATCH System) 0 80 for top tether anchor locations. Do not secure a child seat in a position without a top tether anchor if a national or local law requires that the top tether be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached. If the child restraint or vehicle seat position does not have the LATCH system, you will be using the safety belt to secure the child restraint in this position. Be sure to follow the instructions that came with the child restraint. Secure the child in the child restraint when and as the instructions say.


Seats and Restraints


87


If more than one child restraint needs to be installed in the rear seat, be sure to read Where to Put the Restraint 0 79. 1. Put the child restraint on


the seat. If the head restraint interferes with the proper installation of the child restraint, the head restraint may be removed. See “Head Restraint Removal and Reinstallation” under Lower Anchors and Tethers for Children (LATCH System) 0 80. 2. Pick up the latch plate, and run


the lap and shoulder portions of the vehicle's safety belt through or around the restraint. The child restraint instructions will show you how.


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


88


Seats and Restraints


3. Push the latch plate into the


4. Pull the shoulder belt all the


buckle until it clicks. If the latch plate will not go fully into the buckle, check if the correct buckle is being used. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary.


way out of the retractor to set the lock. When the retractor lock is set, the belt can be tightened but not pulled out of the retractor.


5. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt, and feed the shoulder belt back into the retractor. When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt. Try to pull the belt out of the retractor to make sure the retractor is locked. If the retractor is not locked, repeat Steps 4 and 5.


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


6.


If the child restraint has a top tether, follow the child restraint manufacturer's instructions regarding the use of the top tether. See Lower Anchors and Tethers for Children (LATCH System) 0 80.


7. Before placing a child in the


child restraint, make sure it is securely held in place. To check, grasp the child restraint at the safety belt path and attempt to move it side to side and back and forth. When the child restraint is properly installed, there should be no more than 2.5 cm (1 in) of movement.


To remove the child restraint, unbuckle the vehicle safety belt and let it return to the stowed position. If the top tether is attached to a top tether anchor, disconnect it. If the head restraint was removed, reinstall it before the seating position is used. See “Head Restraint Removal and Reinstallation” under Lower Anchors and Tethers for Children (LATCH System) 0 80.


Securing Child Restraints (Front Passenger Seat) This vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint. See Where to Put the Restraint 0 79. In addition, the vehicle has a passenger sensing system which is designed to turn off the front outboard passenger frontal airbag and passenger knee airbag under certain conditions. See Passenger Sensing System 0 67 and Passenger Airbag Status Indicator 0 104 for more information, including important safety information. Never put a rear-facing child seat in the front. This is because the risk to the rear-facing child is so great, if the airbag deploys.


{ Warning


A child in a rear-facing child restraint can be seriously injured or killed if the front outboard


(Continued)


Seats and Restraints


89


Warning (Continued)


passenger frontal airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag. A child in a forward-facing child restraint can be seriously injured or killed if the front outboard passenger frontal airbag inflates and the passenger seat is in a forward position. Even if the passenger sensing system has turned off the front outboard passenger frontal airbag, no system is fail-safe. No one can guarantee that an airbag will not deploy under some unusual circumstance, even though it is turned off. Secure rear-facing child restraints in a rear seat, even if the airbag is off. If you secure a forward-facing child restraint in the front seat, always move the


(Continued)


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


90


Seats and Restraints


Warning (Continued)


front passenger seat as far back as it will go. It is better to secure the child restraint in a rear seat. See Passenger Sensing System 0 67 for additional information.


If the child restraint uses a top tether, see Lower Anchors and Tethers for Children (LATCH System) 0 80 for top tether anchor locations. Do not secure a child seat in a position without a top tether anchor if a national or local law requires that the top tether be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached.


When using the lap-shoulder belt to secure the child restraint in this position, follow the instructions that came with the child restraint and the following instructions: 1. Move the seat as far back as it


will go before securing the forward-facing child restraint. When the passenger sensing system has turned off the front outboard passenger frontal airbag and passenger knee airbag, the off indicator on the passenger airbag status indicator should light and stay lit when you start the vehicle. See Passenger Airbag Status Indicator 0 104.


2. Put the child restraint on


the seat.


3. Pick up the latch plate, and run


the lap and shoulder portions of the vehicle's safety belt through or around the restraint. The child restraint instructions will show you how.


4. Push the latch plate into the


buckle until it clicks. Position the release button on the buckle, so that the safety belt could be quickly unbuckled if necessary.


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


Seats and Restraints


91


7. Before placing a child in the


child restraint, make sure it is securely held in place. To check, grasp the child restraint at the safety belt path and attempt to move it side-to-side and back-and-forth. When the child restraint is properly installed, there should be no more than 2.5 cm (1 in) of movement.


If the airbags are off, the off indicator in the passenger airbag status indicator will come on and stay on when the vehicle is started. If a child restraint has been installed and the on indicator is lit, see “If the On Indicator Is Lit for a Child Restraint” under Passenger Sensing System 0 67 for more information. To remove the child restraint, unbuckle the vehicle safety belt and let it return to the stowed position.


5. Pull the shoulder belt all the


way out of the retractor to set the lock. When the retractor lock is set, the belt can be tightened but not pulled out of the retractor.


6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt, and feed the shoulder belt back into the retractor. When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt. Try to pull the belt out of the retractor to make sure the retractor is locked. If the retractor is not locked, repeat Steps 5 and 6.


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


Storage


92
Storage


Storage Compartments


Storage Compartments . . . . . . . . 92
Instrument Panel Storage . . . . . . 92
Glove Box . . . . . . . . . . . . . . . . . . . . . 92
Cupholders . . . . . . . . . . . . . . . . . . . . 93
Center Console Storage . . . . . . . 93


Glove Box


Storage Compartments { Warning


Do not store heavy or sharp objects in storage compartments. In a crash, these objects may cause the cover to open and could result in injury.


Instrument Panel Storage


Lift up on the lever to open it. The glove box features a pen holder (1). The intermediate shelf (2) can be removed by pulling on the front edge.


Pull down to open it.


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


Cupholders


Center Console Storage


Storage


93


To reinstall the shelf, slide it into the side guides (1) and push back until it engages into the rear panel (2).


The armrest is adjustable. Lift the lever to move it forward or rearward.


There are two cupholders in the center console with a removable liner. To remove the liner, lift up on the notch on the underside of the rear of the cupholder.


Rear Seat There are two cupholders in the rear seat armrest. Lower the rear seat armrest to access the cupholders.


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


94


Storage


The armrest must be in the rearward position to open it. Lift the lever and then lift up on the armrest to access the storage area. If equipped, there is a USB port and auxiliary input jack inside the storage area. See Auxiliary Devices 0 153.


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


Instruments and Controls


95


Instruments and Controls


Controls


Steering Wheel Adjustment . . . . 96
Steering Wheel Controls . . . . . . . 96
Heated Steering Wheel . . . . . . . . 97
Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Windshield Wiper/Washer . . . . . . 97
Compass . . . . . . . . . . . . . . . . . . . . . . 98
Clock . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Power Outlets . . . . . . . . . . . . . . . . . 99


Warning Lights, Gauges, and Indicators


Warning Lights, Gauges, and


Indicators . . . . . . . . . . . . . . . . . . . 100
Instrument Cluster . . . . . . . . . . . . 101
Speedometer . . . . . . . . . . . . . . . . . 102
Odometer . . . . . . . . . . . . . . . . . . . . . 102
Trip Odometer . . . . . . . . . . . . . . . . 102
Tachometer . . . . . . . . . . . . . . . . . . . 102
Fuel Gauge . . . . . . . . . . . . . . . . . . . 102
Engine Coolant Temperature


Gauge . . . . . . . . . . . . . . . . . . . . . . 103


Safety Belt Reminders . . . . . . . . 103
Airbag Readiness Light . . . . . . . 104
Passenger Airbag Status


Indicator . . . . . . . . . . . . . . . . . . . . 104
Charging System Light . . . . . . . 105
Malfunction Indicator Lamp


(Check Engine Light) . . . . . . . . 105


Brake System Warning


Light . . . . . . . . . . . . . . . . . . . . . . . . 107


Electric Parking Brake


Light . . . . . . . . . . . . . . . . . . . . . . . . 108


Antilock Brake System (ABS)


Warning Light . . . . . . . . . . . . . . . 108


Lane Departure Warning


(LDW) Light . . . . . . . . . . . . . . . . . 109
Vehicle Ahead Indicator . . . . . . 109
Traction Off Light . . . . . . . . . . . . . 109
StabiliTrak® OFF Light . . . . . . . . 109
Traction Control System (TCS)/


StabiliTrak® Light . . . . . . . . . . . . 110
Tire Pressure Light . . . . . . . . . . . 110
Engine Oil Pressure Light . . . . . 111
Low Fuel Warning Light . . . . . . . 111
Security Light . . . . . . . . . . . . . . . . . 111
High-Beam On Light . . . . . . . . . . 112
Front Fog Lamp Light . . . . . . . . . 112
Lamps On Reminder . . . . . . . . . . 112
Cruise Control Light . . . . . . . . . . 112
Door Ajar Light . . . . . . . . . . . . . . . 112


Information Displays


Driver Information


Center (DIC) . . . . . . . . . . . . . . . . 113


Vehicle Messages


Vehicle Messages . . . . . . . . . . . . 116
Battery Voltage and Charging


Messages . . . . . . . . . . . . . . . . . . . 116
Brake System Messages . . . . . 117
Compass Messages . . . . . . . . . . 117
Door Ajar Messages . . . . . . . . . . 117
Engine Cooling System


Messages . . . . . . . . . . . . . . . . . . . 118
Engine Oil Messages . . . . . . . . . 118
Engine Power Messages . . . . . 119
Fuel System Messages . . . . . . . 119
Key and Lock Messages . . . . . . 119
Object Detection System


Messages . . . . . . . . . . . . . . . . . . . 119


Ride Control System


Messages . . . . . . . . . . . . . . . . . . . 120
Security Messages . . . . . . . . . . . 121
Tire Messages . . . . . . . . . . . . . . . . 121
Transmission Messages . . . . . . 121
Washer Fluid Messages . . . . . . 122
Window Messages . . . . . . . . . . . 122


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


96


Instruments and Controls


Vehicle Personalization


Vehicle Personalization . . . . . . . 122


Universal Remote System


Universal Remote System . . . . 128
Universal Remote System


Programming . . . . . . . . . . . . . . . 128


Universal Remote System


Operation . . . . . . . . . . . . . . . . . . . 130


Controls


Steering Wheel Adjustment


Steering Wheel Controls


To adjust the steering wheel: 1. Pull the lever down. 2. Move the steering wheel up


or down.


3. Pull or push the steering wheel


closer or away from you.


4. Lift the lever up to lock the


steering wheel in place.


Do not adjust the steering wheel while driving.


Some audio controls can be adjusted at the steering wheel. b / g (Push to Talk) : For vehicles with a Bluetooth, OnStar, or navigation system, press to interact with those systems. See “Bluetooth” or “OnStar” in the separate infotainment manual. $ / i (Mute/End Call) : Press to silence the vehicle speakers only. Press again to turn the sound on. For vehicles with OnStar or Bluetooth systems, press to reject an incoming call, or end a current call.


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


Instruments and Controls


97


_ SRC ^ (Source) : Press to select an audio source. Move the thumbwheel up or down to select the next or previous favorite radio station, CD, or MP3 track. + x − (Volume) : Press + to increase the volume. Press − to decrease the volume.


Heated Steering Wheel


The steering wheel takes about three minutes to start heating.


Horn Press a on the steering wheel pad to sound the horn.


Windshield Wiper/Washer


The windshield wiper/washer lever is on the right side of the steering column. With the ignition in ACC/ ACCESSORY or ON/RUN, move the windshield wiper lever to select the wiper speed. HI : Use for fast wipes. LO : Use for slow wipes.


((Heated Steering Wheel) : For vehicles with a heated steering wheel, press to turn it on or off. A light on the button displays when the feature is turned on.


INT (Intermittent Wipes) : Move the lever up to INT for intermittent wipes, then turn the x INT band up for more frequent wipes or down for less frequent wipes. OFF : Use to turn the wipers off. 1X (Mist) : For a single wipe, briefly move the wiper lever down. For several wipes, hold the wiper lever down. n L(Windshield Washer) : Pull the windshield wiper lever toward you to spray windshield washer fluid and activate the wipers. The wipers will continue until the lever is released or the maximum wash time is reached. When the windshield wiper lever is released, additional wipes may occur depending on how long the windshield washer had been


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


98


Instruments and Controls


activated. See Washer Fluid 0 243
for information on filling the windshield washer fluid reservoir.


{ Warning


In freezing weather, do not use the washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision.


Clear snow and ice from the wiper blades and windshield before using them. If frozen to the windshield, carefully loosen or thaw them. Damaged blades should be replaced. See Wiper Blade Replacement 0 248. Heavy snow or ice can overload the wiper motor.


Wiper Parking If the ignition is turned to LOCK/ OFF while the wipers are on LO, HI, or INT, they will immediately stop.


If the windshield wiper lever is then moved to off before the driver door is opened or within 10 minutes, the wipers will restart and move to the base of the windshield. If the ignition is turned to LOCK/ OFF while the wipers are performing wipes due to windshield washing, the wipers continue to run until they reach the base of the windshield.


Compass The vehicle may have a compass display on the Driver Information Center (DIC). The compass receives its heading and other information from the Global Positioning System (GPS) antenna, StabiliTrak®, and vehicle speed information. The compass system is designed to operate for a certain number of miles or degrees of turn before needing a signal from the GPS satellites. When the compass display shows CAL, drive the vehicle for a short distance in an open area where it can receive a GPS signal. The compass system


will automatically determine when a GPS signal is restored and provide a heading again. See Compass Messages 0 117 for the messages that may be displayed for the compass.


Clock The infotainment system controls are used to access the time and date settings through the menu system. The clock menu can be only be used with the radio on while in ON/RUN or ACC/ACCESSORY. See Operation 0 141 for information about how to use the menu system. Setting the Clock (Radio with CD) To set the time: 1. Press the CONFIG button and


select Time and Date or press H.


2. Select Set Time. 3. Turn the TUNE/MENU knob to adjust the highlighted number.


4. Press TUNE/MENU to select


the next number.


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


5. To save the time and return to


the Time and Date menu, press / BACK at any time or press the TUNE/MENU knob after adjusting the minutes.


Setting the 12/24 Hour Format 1. Press the CONFIG button and


select Time and Date or press H.


2. Highlight 12/24 Hour Format. 3. Press TUNE/MENU to select


the 12 hour or 24 hour display format.


Setting the Clock (Radio with CD and Touch Screen) The clock is in the center stack display. To set the time: 1. Press the CONFIG button to


enter the menu options or press H. Turn the TUNE/ MENU knob to scroll through the available setup features and select Time and Date. Press TUNE/MENU or press


Instruments and Controls


99


the Time screen button to display other options within that feature.


2. Press + or − to increase or


decrease the Hours and Minutes displayed on the clock.


If auto timing is set, the time displayed on the clock may not update immediately when driving into a new time zone. 12/24 HR Format : Press the 12 HR screen button for standard time; press the 24 HR screen button for military time. Day + or Day − : Press the Day + or Day − display buttons to increase or decrease the day. Display : Press Display to turn the display of the time on the screen on or off.


Power Outlets The accessory power outlets can be used to plug in electrical equipment, such as a cell phone or MP3 player.


There is one accessory power outlet located on the center stack below the climate control and one on the rear of the center floor console. These outlets are powered when the key is in ON/RUN or ACC/ ACCESSORY, or until the driver door is opened within 10 minutes of turning off the vehicle. See Retained Accessory Power (RAP) 0 191.


Caution


Leaving electrical equipment plugged in for an extended period of time while the vehicle is off will drain the battery. Always unplug electrical equipment when not in use and do not plug in equipment that exceeds the maximum 20 amp rating.


Certain electrical accessories may not be compatible with the accessory power outlet and could overload vehicle or adapter fuses. If a problem is experienced, see your dealer.


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


100


Instruments and Controls


When adding electrical equipment, be sure to follow the installation instructions included with the equipment. See Add-On Electrical Equipment 0 225.


Caution


Hanging heavy equipment from the power outlet can cause damage not covered by the vehicle warranty. The power outlets are designed for accessory power plugs only, such as cell phone charge cords.


Warning Lights, Gauges, and Indicators Warning lights and gauges can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to the warning lights and gauges could prevent injury.


Some warning lights come on briefly when the engine is started to indicate they are working. When one of the warning lights comes on and stays on while driving, or when one of the gauges shows there may be a problem, check the section that explains what to do. Waiting to do repairs can be costly and even dangerous.


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


Instrument Cluster


Instruments and Controls


101


English Cluster Shown, Metric Similar


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


102


Instruments and Controls


Speedometer The speedometer shows the vehicle speed in kilometers per hour (km/h) and miles per hour (mph).


Odometer The odometer shows how far the vehicle has been driven, in either kilometers or miles.


Trip Odometer The trip odometer shows how far the vehicle has been driven since the trip odometer was last reset. The trip odometer is accessed and reset through the Driver Information Center (DIC). See Driver Information Center (DIC) 0 113.


Tachometer The tachometer displays the engine speed in revolutions per minute (rpm).


Caution


If the engine is operated with the rpm’s in the warning area at the high end of the tachometer, the vehicle could be damaged, and the damage would not be covered by the vehicle warranty. Do not operate the engine with the rpm’s in the warning area.


Fuel Gauge


When the ignition is on, the fuel gauge tells you about how much fuel you have left in your tank.


An arrow on the fuel gauge indicates the side of the vehicle the fuel door is on. When the fuel is low, a message may appear in the Driver Information Center (DIC), and a chime will sound. See Fuel System Messages 0 119 for more information. Here are four things that some owners ask about. None of these show a problem with your fuel gauge: . At the service station, the fuel


pump shuts off before the gauge reads full. It takes a little more or less fuel to fill up than the gauge indicated. For example, the gauge may have indicated the tank was half full, but it actually took a little more or less than half the tank's capacity to fill the tank.


. The gauge moves a little while


turning a corner or speeding up.


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


Instruments and Controls


103


. The gauge takes a few seconds


to stabilize after the ignition is turned on, and will go back to empty when the ignition is turned off.


If the vehicle has been operated under normal driving conditions, pull off the road, stop the vehicle, and turn off the engine as soon as possible.


Engine Coolant Temperature Gauge


Safety Belt Reminders


Driver Safety Belt Reminder Light There is a driver safety belt reminder light on the instrument cluster.


If the driver safety belt is buckled, neither the light nor the chime comes on. Passenger Safety Belt Reminder Light There is a passenger safety belt reminder light near the passenger airbag status indicator. See Passenger Sensing System 0 67.


English Shown, Metric Similar


This gauge shows the engine coolant temperature. If the indicator needle moves to the hot side of the gauge toward the shaded area, the engine is too hot.


When the vehicle is started, this light flashes and a chime may come on to remind the driver to fasten their safety belt. Then the light stays on solid until the belt is buckled. This cycle may continue several times if the driver remains or becomes unbuckled while the vehicle is moving.


When the vehicle is started, this light flashes and a chime may come on to remind passengers to fasten their safety belt. Then the light stays on solid until the belt is buckled. This cycle continues several times if the passenger remains or becomes unbuckled while the vehicle is moving. If the passenger safety belt is buckled, neither the chime nor the light comes on.


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


104


Instruments and Controls


The front passenger safety belt reminder light and chime may turn on if an object is put on the seat such as a briefcase, handbag, grocery bag, laptop, or other electronic device. To turn off the reminder light and/or chime, remove the object from the seat or buckle the safety belt.


Airbag Readiness Light This light shows if there is an electrical problem with the airbag system. The system check includes the airbag sensor(s), passenger sensing system, the pretensioners, the airbag modules, the wiring, and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System 0 61.


The airbag readiness light comes on for several seconds when the vehicle is started. If the light does not come on then, have it fixed immediately.


{ Warning


If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash. To help avoid injury, have the vehicle serviced right away.


Passenger Airbag Status Indicator The vehicle has a passenger sensing system. See Passenger Sensing System 0 67 for important safety information. The center stack has a passenger airbag status indicator.


When the vehicle is started, the passenger airbag status indicator will light ON and OFF for several seconds as a system check. Then, after several seconds, the status indicator will light either ON or OFF to let you know the status of the front outboard passenger frontal airbag and knee airbag. If the word ON is lit on the passenger airbag status indicator, it means that the front outboard passenger frontal airbag and knee airbag are allowed to inflate. If the word OFF is lit on the passenger airbag status indicator, it means that the passenger sensing system has turned off the front outboard passenger frontal airbag and passenger knee airbag. If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


problem with the lights or the passenger sensing system. See your dealer for service.


{ Warning


If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light 0 104 for more information, including important safety information.


Charging System Light


The charging system light comes on briefly when the ignition is turned on, but the engine is not running, as a check to show the light is working.


Instruments and Controls


105


The light turns off when the engine is started. If it does not, have the vehicle serviced by your dealer. If the light stays on, or comes on while driving, there could be a problem with the electrical charging system. Have it checked by your dealer. Driving while this light is on could drain the battery. If a short distance must be driven with the light on, be sure to turn off all accessories, such as the radio and air conditioner.


Malfunction Indicator Lamp (Check Engine Light) This light is part of the vehicle’s emission control on-board diagnostic system. If this light is on while the engine is running, a malfunction has been detected and the vehicle may require service. The light should come on to show that it is working when the ignition is in ON/RUN with the engine not running for Key Access or in Service Only Mode for Keyless Access.


See Ignition Positions (Keyless Access) 0 185 or Ignition Positions (Key Access) 0 186.


Malfunctions are often indicated by the system before any problem is noticeable. Being aware of the light and seeking service promptly when it comes on may prevent damage.


Caution


If the vehicle is driven continually with this light on, the emission control system may not work as well, the fuel economy may be lower, and the vehicle may not run smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty.


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


106


Instruments and Controls


Caution


Modifications to the engine, transmission, exhaust, intake, or fuel system, or the use of replacement tires that do not meet the original tire specifications, can cause this light to come on. This could lead to costly repairs not covered by the vehicle warranty. This could also affect the vehicle’s ability to pass an Emissions Inspection/ Maintenance test. See Accessories and Modifications 0 227.


If the light is flashing : A malfunction has been detected that could damage the emission control system and increase vehicle emissions. Diagnosis and service may be required. To help prevent damage, reduce vehicle speed and avoid hard accelerations and uphill grades.


If towing a trailer, reduce the amount of cargo being hauled as soon as possible. If the light continues to flash, find a safe place to park. Turn the vehicle off and wait at least 10 seconds before restarting the engine. If the light is still flashing, follow the previous guidelines and see your dealer for service as soon as possible. If the light is on steady : A malfunction has been detected. Diagnosis and service may be required. Check the following: . A loose or missing fuel cap may cause the light to come on. See Filling the Tank 0 218. A few driving trips with the cap properly installed may turn the light off.


. Poor fuel quality can cause


inefficient engine operation and poor driveability, which may go away once the engine is warmed up. If this occurs, change the fuel brand. It may require at


least one full tank of the proper fuel to turn the light off. See Fuel 0 216.


If the light remains on, see your dealer. Emissions Inspection and Maintenance Programs If the vehicle requires an Emissions Inspection/Maintenance test, the test equipment will likely connect to the vehicle's Data Link Connector (DLC).


The DLC is under the instrument panel to the left of the steering wheel. Connecting devices that are not used to perform an Emissions Inspection/Maintenance test or to service the vehicle may affect vehicle operation See Add-On Electrical Equipment 0 225. See your dealer if assistance is needed.


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


Instruments and Controls


107


The vehicle may not pass inspection if: . The light is on when the engine


is running.


. The light does not come on


when the ignition is in ON/RUN with the engine not running for Key Access or in Service Only Mode for Keyless Access.


. Critical emission control systems


have not been completely diagnosed. If this happens, the vehicle would not be ready for inspection and might require several days of routine driving before the system is ready for inspection. This can happen if the 12-volt battery has recently been replaced or run down, or if the vehicle has been recently serviced.


See your dealer if the vehicle will not pass or cannot be made ready for the test.


Brake System Warning Light The vehicle brake system consists of two hydraulic circuits. If one circuit is not working, the remaining circuit can still work to stop the vehicle. For normal braking performance, both circuits need to be working. The brake system warning light will come on with the electric parking brake light when the electric parking brake is applied. Both lights will stay on until the electric parking brake is released. The brake system warning light will also come on when there is a brake problem. If the warning light stays on when the electric parking brake is not applied, have the vehicle inspected by your dealer right away.


Metric


English


The brake indicator light should come on briefly as the engine is started. If it does not come on have the vehicle serviced by your dealer.


{ Warning


The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service.


If the light comes on while driving, a chime sounds. Pull off the road and stop. The pedal might be harder to push or go closer to the floor.


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


108


Instruments and Controls


It might also take longer to stop. If the light is still on, have the vehicle towed for service. See Towing the Vehicle 0 291.


Electric Parking Brake Light


The brake system warning light will come on with the electric parking brake light when the electric parking brake is applied. Both lights will stay on until the electric parking brake is released. If the light does not come on, or remains flashing, see your dealer.


If this light comes on, there is a problem with a system on the vehicle that is causing the EPB to work at a reduced level. The vehicle can still be driven, but should be taken to a dealer as soon as possible. See Parking Brake 0 200
for more information.


The Electric Parking Brake (EPB) light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. The parking brake status light comes on when the brake is applied. If the light continues flashing after the parking brake is released, or while driving, there is a problem with the EPB system. A message may also display in the Driver Information Center (DIC). See Brake System Messages 0 117
for more information.


Antilock Brake System (ABS) Warning Light


The Antilock Brake System (ABS) light comes on briefly when the engine is started. If the light does not come on, have the vehicle serviced by your dealer. If the ABS light comes on and stays on while driving, stop as soon as possible and turn the ignition off. Start the engine again to reset the system. If the light stays on after driving at a speed above 20 km/h (13 mph), see your dealer for service. A chime may also sound when the light comes on steady. If the regular brake system warning light is not on, the vehicle still has brakes, but not antilock brakes. If the regular brake system warning light is also on, the vehicle does not


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


have antilock brakes and there is a problem with the regular brakes. See Brake System Warning Light 0 107. See Brake System Messages 0 117
for all brake‐related DIC messages.


Lane Departure Warning (LDW) Light


If equipped, this light comes on briefly while starting the vehicle. If it does not come on, have the vehicle serviced. This light is green if LDW is on and ready to operate. This light changes to amber and flashes to indicate that the lane marking has been crossed without using a turn signal in that direction. See Lane Departure Warning (LDW) 0 215.


Vehicle Ahead Indicator


If equipped, this indicator will display green when a vehicle is detected ahead See Forward Collision Alert (FCA) System 0 211.


Traction Off Light


Instruments and Controls


109


The traction off light comes on when the Traction Control System (TCS) has been turned off by pressing and releasing the TCS/StabiliTrak button. This light and the StabiliTrak OFF light come on when StabiliTrak is turned off. If the TCS is off, wheel spin is not limited. Adjust driving accordingly. See Traction Control/Electronic Stability Control 0 203.


StabiliTrak® OFF Light


This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. If the system is working normally, the indicator light then turns off.


This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer.


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


110


Instruments and Controls


This light comes on when the StabiliTrak system is turned off. If StabiliTrak is off, the Traction Control System (TCS) is also off. If the StabiliTrak and TCS are off, the system does not assist in controlling the vehicle. Turn on the TCS and the StabiliTrak systems and the warning light turns off. See Traction Control/Electronic Stability Control 0 203.


Traction Control System (TCS)/StabiliTrak® Light


If the light is on and not flashing, the TCS and potentially the StabiliTrak system have been disabled. A DIC message may display. Check the DIC messages to determine which feature(s) is no longer functioning and whether the vehicle requires service. If the light is on and flashing, the TCS and/or the StabiliTrak system is actively working. See Traction Control/Electronic Stability Control 0 203.


Tire Pressure Light


This light comes on briefly when the engine is started. If the light does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off.


For vehicles with the Tire Pressure Monitor System (TPMS), this light comes on briefly when the engine is started. It provides information about tire pressures and the TPMS.


When the Light Is On Steady This indicates that one or more of the tires are significantly underinflated. A Driver Information Center (DIC) tire pressure message may also display. See Tire Messages 0 121. Stop as soon as possible, and inflate the tires to the pressure value shown on the Tire and Loading Information label. See Tire Pressure 0 268.


When the Light Flashes First and Then Is On Steady If the light flashes for about a minute and then stays on, there may be a problem with the TPMS. If the problem is not corrected, the light will come on at every ignition cycle. See Tire Pressure Monitor Operation 0 270.


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


Engine Oil Pressure Light


Caution


Lack of proper engine oil maintenance can damage the engine. Driving with the engine oil low can also damage the engine. The repairs would not be covered by the vehicle warranty. Check the oil level as soon as possible. Add oil if required, but if the oil level is within the operating range and the oil pressure is still low, have the vehicle serviced. Always follow the maintenance schedule for changing engine oil.


This light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer.


Instruments and Controls


111


If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle could be low on oil and might have some other system problem. See your dealer.


Low Fuel Warning Light


The low fuel warning light comes on and a chime sounds when the vehicle is low on fuel. The light turns off when fuel is added to the fuel tank. For more information on the Driver Information Center (DIC), see Fuel System Messages 0 119.


Security Light


This light comes on for a few seconds when the ignition is turned on as a check to indicate it is working. If it does not come on, have it fixed.


The security light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off. If the light stays on and the engine does not start, there could be a problem with the theft-deterrent system. See Immobilizer Operation (Key Access) 0 40 or Immobilizer Operation (Keyless Access) 0 41.


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


112


Instruments and Controls


High-Beam On Light


The high‐beam on light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer 0 132 for more information.


Front Fog Lamp Light


For vehicles with front fog lamps, this light comes on when the front fog lamps are in use.


The light goes out when the front fog lamps are turned off. See Front Fog Lamps 0 134 for more information.


Lamps On Reminder


For vehicles with cruise control, the cruise control light is white when the cruise control is on and ready, and turns green when the cruise control is set and active. The light turns off when the cruise control is turned off. See Cruise Control 0 205.


Door Ajar Light


This light comes on when the exterior lamps are in use. See Exterior Lamp Controls 0 131.


Cruise Control Light


If equipped, this light comes on when a door is open or not securely latched. Before driving, check that all doors are properly closed. See Door Ajar Messages 0 117.


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


Instruments and Controls


113


Information Displays


Driver Information Center (DIC) The Driver Information Center (DIC) displays information about the vehicle. It also displays warning messages if a system problem is detected. See Vehicle Messages 0 116. All messages appear in the DIC display in the center of the instrument cluster. On some models, the DIC may have some warning lights or indicators shown in the top portion of the display. See Warning Lights, Gauges, and Indicators 0 100. The vehicle may also have features that can be customized through the controls on the radio. See Vehicle Personalization 0 122. DIC Operation and Displays The DIC has different displays which can be accessed by using the DIC buttons on the turn signal lever. The DIC displays trip, fuel, and


vehicle system information, and warning messages if a system problem is detected. The bottom of the DIC display shows the position of the shift lever and the odometer. It may also show the direction the vehicle is driving. In cold weather the DIC display may change slowly. This is normal and will move more quickly as the vehicle's interior temperature rises.


DIC Buttons


1. SET/CLR (Set/Clear): Press to


set or clear the menu item when it is displayed.


2. w / x (Thumbwheel): Use to scroll through the items in each menu. A small marker will move across the bottom of the


page as you scroll through the items. This shows where each page is in the menu.


3. MENU: Press to get to the Trip/


Fuel Menu and the Vehicle Information Menu. This button is also used to return to or exit the last screen displayed on the DIC.


Trip/Fuel Menu Items Press MENU on the turn signal lever until the Trip/Fuel Menu is displayed. Use w / x to scroll through the following menu items: . Digital Speedometer . Trip 1
. Trip 2
. Fuel Range . Average Fuel Economy . Average Vehicle Speed . Timer . Navigation . Blank Display


Instantaneous Fuel Economy


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


114


Instruments and Controls


Digital Speedometer The speedometer shows how fast the vehicle is moving in either kilometers per hour (km/h) or miles per hour (mph). The speedometer cannot be reset.


Trip 1 and Trip 2
These displays show the current distance traveled, in either kilometers (km) or miles (mi), since the last reset for the trip odometer. The trip odometer can be reset to zero by pressing SET/CLR, or the trip odometer reset stem in the cluster, while the trip odometer display is showing.


Fuel Range This display shows the approximate distance the vehicle can be driven without refueling. The fuel range estimate is based on an average of the vehicle's fuel economy over recent driving history and the amount of fuel remaining in the fuel tank. Fuel range cannot be reset.


Average Fuel Economy This display shows the approximate average liters per 100 kilometers (L/ 100 km) or miles per gallon (mpg). Average fuel economy is calculated based on the number of L/ 100 km (mpg) recorded since the last time this menu item was reset. This number reflects only the approximate average fuel economy that the vehicle has right now, and will change as driving conditions change. The average fuel economy can be reset by pressing SET/CLR while the Average Fuel Economy display is showing.


Instantaneous Fuel Economy The instantaneous fuel economy display shows the current fuel economy in liters per 100 kilometers (L/100 km) or miles per gallon (mpg). The instantaneous fuel economy reflects only the current approximate fuel economy and changes frequently as driving conditions change. Unlike average economy, this display cannot be reset.


Average Vehicle Speed This display shows the average speed of the vehicle in kilometers per hour (km/h) or miles per hour (mph). This average is calculated based on the various vehicle speeds recorded since the last reset of this value. The average speed can be reset by pressing SET/CLR while the Average Vehicle Speed display is showing.


Timer This display can be used as a timer. To start the timer, press SET/CLR while Timer is displayed. The display will show the amount of time that has passed since the timer was last reset, not including time the ignition is off. Time will continue to be counted as long as the ignition is on, even if another display is being shown on the DIC. The timer will record up to 99 hours, 59 minutes, and 59 seconds (99:59:59) after which the display will return to zero. To stop the timer, press SET/CLR briefly while Timer is displayed. To reset the timer to zero, press and hold SET/CLR.


Buick Verano Owner Manual 9085356) - 2016 - CRC - 5/20/15


(GMNA-Localizing-U.S./Canada/Mexico-


Navigation This display is used for the Navigation System Turn-by-Turn guidance. See the infotainment manual, if the vehicle has navigation, for more information.


Blank Display This display shows no information. Vehicle Information Menu Items Press MENU on the turn signal lever until the Vehicle Information Menu is displayed. Use w / x to scroll through the following menu items: . Unit . Tire Pressure . Remaining Oil Life . Battery Voltage


Unit Press SET/CLR to set. Move w / x to switch between metric or US when the set Unit display is active. Press SET/CLR to confirm the setting. This will change the


Instruments and Controls


115


displays on the cluster and DIC to either metric or English (US) measurements.


Tire Pressure The display will show a vehicle with the approximate pressures of all four tires. Tire pressure is displayed in either kilopascal (kPa) or pounds per square inch (psi). See Tire Pressure Monitor System 0 269 and Tire Pressure Monitor Operation 0 270 for more information.


Remaining Oil Life This display shows an estimate of the oil's remaining useful life. If REMAINING OIL LIFE 99% is displayed, that means 99% of the current oil life remains. When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See Engine Oil Messages 0 118. The oil should be changed as soon as possible. See Engine Oil 0 233. In addition to the Engine Oil Life System monitoring the oil life, additional maintenance is recommended in the Maintenance


Schedule in this manual. See Maintenance Schedule 0 305 for more information. Remember, the Remaining Oil Life display must be reset after each oil change. It will not reset itself. Also, be careful not to reset the Remaining Oil Life display accidentally at any time other than when the oil has just been changed. It cannot be reset accurately until

Loading...
x