2005 Buick Terraza Owners Manual

Download PDF Manual
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. At times you may notice a decrease in range. This is normal for any remote keyless entry system. If the transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work, try this: (cid:127) Check the distance. You may be too far from your vehicle. You may need to stand closer during rainy or snowy weather. (cid:127) Check the location. Other vehicles or objects may be blocking the signal. Take a few steps to the left or right, hold the transmitter higher, and try again. (cid:127) Check to determine if battery replacement is necessary. See “Battery Replacement” under Remote Keyless Entry System Operation on page 2-5. If you are still having trouble, see your dealer or a qualiﬁed technician for service. (cid:127) Remote Keyless Entry System Operation You can lock and unlock the vehicle’s doors and the liftgate from about 3 feet (1 m) up to 30 feet (9 m) away using the remote keyless entry transmitter supplied with your vehicle. The remote keyless entry transmitter shown here is for a vehicle equipped with the remote vehicle start feature and dual power sliding doors. The remote keyless entry transmitter supplied with your vehicle will only contain the buttons speciﬁc to your vehicle’s factory installed remote system features. / (Remote Vehicle Start): If your vehicle has this feature, you can start the engine from outside the vehicle. See “Remote Vehicle Start” at the end of this section for more detailed information. " (Unlock): When you press unlock on the remote keyless entry transmitter, only the driver’s door will unlock. If you press unlock again within ﬁve seconds, all the doors and the liftgate will unlock. If you would like all the doors to unlock the ﬁrst time you press unlock, see “FOB UNLOCK ON 1ST PRESS” under DIC Vehicle Personalization (Uplevel Only) on page 3-68. If your vehicle has the content theft-deterrent system, the unlock button on the remote keyless entry transmitter will disarm the system. See Content Theft-Deterrent on page 2-26 for more details. When you use your remote keyless entry transmitter to unlock your vehicle the turn signal lamps will ﬂash to let you know the command was received. Q(Lock): To lock all doors and the liftgate, press the lock button on the remote keyless entry transmitter. See Power Door Locks on page 2-11 for more details on the power door lock features. If your vehicle has the content theft-deterrent system, the remote keyless entry transmitter’s lock button may arm the system. See Content Theft-Deterrent on page 2-26 for more details. 2-5 When you use the remote keyless entry transmitter to lock your vehicle, the turn signal lamps may ﬂash to let you know the command has been received. If you press the lock button again, within ﬁve seconds, the horn will sound and the turn signal lamps may ﬂash to let you know the vehicle is already locked. See “FOB LOCK FEEDBACK” under DIC Vehicle Personalization (Uplevel Only) on page 3-68 for additional information. L (Remote Alarm): When you press the horn button on the remote keyless entry transmitter, the turn signal lamps will ﬂash and the horn will sound. This will allow you to attract attention, if needed. Press this button again to stop the alarm from sounding. Remote Power Sliding Door Operation + (Power Sliding Door): If your vehicle has one power sliding door, the remote keyless entry transmitter will have a button with a van symbol on it. Press and hold this button to open or close the power sliding door. See Power Sliding Door (PSD) on page 2-16. * + (Dual Power Sliding Doors): If your vehicle has dual power sliding doors, your remote keyless entry transmitter will have two buttons that have a van symbol on them. The van symbol on the left is for the driver’s side sliding door and the van symbol on the right is for the passenger’s side sliding door. Press and hold the passenger’s or driver’s side button, with the van symbol on it, to open or close the selected power sliding door. See Power Sliding Door (PSD) on page 2-16. You can operate the power sliding door(s) with the remote keyless entry transmitter only when the power sliding door override switch(es) on the overhead console is active. See Power Sliding Door (PSD) on page 2-16 for additional information. If the sliding door is closed and the power sliding door button on the transmitter is pressed and held, the vehicle’s doors will be unlocked and then the power sliding door will open. If the power sliding door has been locked using the manual door lock lever, you will need to unlock the power sliding door before it can be opened with the keyless entry transmitter sliding door button. If your vehicle’s fuel ﬁller door is opened, the driver’s side power sliding door will not open completely. Do not try to force the door. Once the fuel ﬁller door is closed, the driver’s side sliding door can be opened normally. 2-6 Matching Transmitter(s) to Your Vehicle Each remote keyless entry transmitter is coded to prevent another transmitter from unlocking your vehicle. If a transmitter is lost or stolen, a replacement can be purchased through your dealer. Remember to bring any remaining transmitters with you when you go to your dealer. When the dealer matches the replacement transmitter to your vehicle, any remaining transmitters must also be matched. Once your dealer has coded the new transmitter, the lost transmitter will not unlock your vehicle. Each vehicle can have a maximum of four transmitters matched to it. See your dealer to match transmitters to another vehicle. Battery Replacement Under normal use, the battery in your remote keyless entry transmitter should last about three years. You can tell the battery is weak if the transmitter will not work at the normal range in any location. If you have to get close to your vehicle before the transmitter works, it is probably time to change the battery. Notice: When replacing the battery, use care not to touch any of the circuitry. Static from your body transferred to these surfaces may damage the transmitter. 1. Insert a ﬂat object, such as a coin, into the slot on the side of the transmitter and twist it to separate the halves. 2. Gently pry the battery out of the transmitter. Do not use the metal ﬂanges to pop out the battery. 3. Replace the battery. 4. Reassemble the transmitter. Make sure the halves are snapped together tightly so water will not get in. 5. Press and hold the lock and unlock buttons for seven seconds to synchronize the transmitter. 6. Check the transmitter operation. 2-7 Remote Vehicle Start This feature allows you to start the engine from outside the vehicle. Laws in some local communities may restrict the use of remote starters. For example, some laws may require a person using remote start to have the vehicle in view when doing so. Check local regulations for any requirements on remote starting of vehicles. / (Remote Vehicle Start): If your vehicle has the remote vehicle start feature, the remote keyless entry transmitter will have a button with this symbol on it. An increased range of operation is provided with the remote keyless entry transmitter that has the remote vehicle start button. The vehicle can be started from approximately 180 feet (60 m) away. However, the operating range may be less while the engine is running and you will need to be closer to your vehicle to turn it off than you were to turn it on. Do not use the remote start feature if your vehicle is low on fuel. Your vehicle may run out of fuel. To start the engine using the remote start feature, do the following: 1. Aim the remote keyless entry transmitter, equipped with the remote vehicle start button, at the vehicle. 2. Press and release the transmitter’s lock button, then immediately press and hold the remote vehicle start button until the vehicle’s turn signal lamps ﬂash, or for at least two seconds, if the vehicle’s lights are not visible. The vehicle’s doors will be locked. 3. When the vehicle’s engine starts, the parking lamps will turn on and remain on while the engine is running. After a remote start, the engine will automatically shut off after 10 minutes unless a time extension has been done or the vehicle’s key is inserted into the ignition switch and turned to RUN. The maximum number of remote starts or remote start attempts between ignition cycles with the key is two. If it is the vehicle’s ﬁrst remote start, and the engine is still running, repeat Steps 1 and 2 for a 10 minute time extension. Ten minutes will be added to the remaining minutes of the ﬁrst remote start. The 10 minute time extension is considered a second remote start. 2-8 After two remote starts have been provided, the vehicle’s ignition switch must be turned to RUN and then back to LOCK using the key before the remote start procedure can be used again. If you enter the vehicle after a remote start, and the engine is running, insert the key into the ignition switch and turn it to the RUN position to drive the vehicle. To manually shut off the engine after a remote start, do any of the following: (cid:127) Aim the remote keyless entry transmitter at the vehicle and press the remote start button until the parking lamps turn off. Turn on the hazard warning ﬂashers. Insert the vehicle’s key into the ignition switch and turn the switch to RUN and then back to LOCK. The remote vehicle start feature will not operate if: The remote start system is disabled. See “REMOTE START” under DIC Vehicle Personalization (Uplevel Only) on page 3-68. The vehicle’s key is in the ignition. The vehicle’s hood, liftgate or doors are not closed. The hazard warning ﬂashers are on. There is an emission control system malfunction. The engine coolant temperature is too high. The oil pressure is low. Two remote vehicle starts have already been provided. The maximum number of remote starts or remote start attempts between ignition cycles with the key is two. 2-9 (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) There are several ways to lock and unlock your vehicle. From the outside, use your key or the remote keyless entry transmitter. To unlock the driver’s door from the outside with the key, insert the key and turn it toward the front of the vehicle. To lock the driver’s door from the outside with your key, insert the key and turn it toward the rear of the vehicle. If your vehicle has power door locks, you may be able to unlock all of the doors and the liftgate when you insert the key, turn it toward the front of the vehicle, and hold it there for one second. You may be able to lock all of the doors when you insert the key and turn it toward the rear of the vehicle. Doors and Locks Door Locks {CAUTION: Unlocked doors can be dangerous. (cid:127) Passengers — especially children — can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked. So, wear safety belts properly and lock the doors whenever you drive. (cid:127) Young children who get into unlocked vehicles may be unable to get out. A child can be overcome by extreme heat and can suffer permanent injuries or even death from heat stroke. Always lock your vehicle whenever you leave it. (cid:127) Outsiders can easily enter through an unlocked door when you slow down or stop your vehicle. Locking your doors can help prevent this from happening. 2-10 Power Door Locks From the inside, press the top of the power door lock switch, located on either front door, to unlock all doors and the liftgate. From the inside, use the manual or power door locks. To unlock either front door from the inside, pull back on the manual lever. To lock either front door from the inside, push the manual lever forward. With the content theft-deterrent system, the power door lock switch will not unlock the doors until the system is disarmed. See Content Theft-Deterrent on page 2-26 for more details. 2-11 You can lock all doors and the liftgate from the inside by pressing the bottom of the power lock switch on either front door. With the content theft-deterrent system, the power door lock switch may cause the system to arm. See Content Theft-Deterrent on page 2-26 for more details. If the liftgate has been unlocked with the power door locks, you will not need the key to open it. Squeeze the handle located above the license plate to open the liftgate. This is also true if you use the remote keyless entry transmitter. See Remote Keyless Entry System on page 2-4. Delayed Locking This feature allows the locking of the vehicle to be delayed until all doors have been closed for approximately ﬁve seconds. To activate the delayed locking feature, do one of the following: (cid:127) Press the driver’s door power lock switch one time while the driver’s door is open. (cid:127) Press the passenger’s door power lock switch one time while the passenger’s door is open. (cid:127) Press the lock button on the remote keyless entry transmitter one time while any door is open. 2-12 Two chimes will sound to signal that delayed locking is active. The doors may be locked immediately by repeating any of the above actions more than one time. If a door remains open, without any other door being opened or closed, the vehicle will lock after approximately 45 seconds. If the key is in the ignition, this feature will not lock the doors. To turn the delayed locking feature off or on, see DIC Vehicle Personalization (Uplevel Only) on page 3-68. Sliding Door Delayed Locking If either sliding door is open when you use the power door locks to lock the vehicle, the sliding door that is open will not lock. Normally the delayed locking feature will be used to lock the sliding door after it has been closed. The sliding door delayed locking feature will lock your sliding door(s) in situations where the delayed locking feature does not apply or was overridden or programmed to be off. See “Delayed Locking” earlier in this section. Shortly after the last sliding door is closed, all the doors will lock. Programmable Automatic Door Locks All of the doors will lock automatically when you move your shift lever to a forward gear. All doors will unlock automatically when the shift lever is moved into PARK (P). If someone needs to get out while you are not in PARK (P), shift into PARK (P), or, have that person use the manual lever or the power door lock switch. When the door is closed again, it will lock when the vehicle exceeds 5 mph (8 kph). Use the manual lever or the power door lock switch to lock the door. To change the way automatic door locks operate, see DIC Vehicle Personalization (Uplevel Only) on page 3-68. With the automatic door locks feature, you can lock or unlock the doors at any time, either manually or using the power door lock switches. Lockout Protection The lockout protection feature makes it more difficult to lock the key in the vehicle. If the driver’s door is open while the key is in the ignition, the door cannot be locked with the power door lock switch. This feature cannot guarantee that you will never be locked out of the vehicle. If the key is not left in the ignition, or, if the manual door lock is used, the key could still be locked inside the vehicle. Always remember to take the key with you. Dual Sliding Doors To open either sliding door from outside the vehicle, pull the handle out and then pull the door toward the rear. If you slide the door all the way back, the door will rest in a detent position. To move the door forward, you must ﬁrst pull the door past the open detent position. The driver’s side sliding door is designed to open only a little if the fuel door is open. If this ever happens, do not try to force the sliding door. Just close the driver’s side sliding door. Then when the fuel ﬁller door is closed, the driver’s side sliding door can be opened normally. 2-13 {CAUTION: If your vehicle is facing downward on a steep grade (15 percent or more), the door may not stay open and could slam shut, possibly injuring someone. To make sure the door does not slam shut be sure to hold it open until everyone is clear of the door, and only then allow it to slowly close. Sliding Door Lock 2-14 Lock either sliding door from inside the vehicle by moving the manual lever down. Unlock it by moving the lever up. With the power door locks, the sliding door lock has a delay feature. See Delayed Locking on page 2-12 and DIC Vehicle Personalization (Uplevel Only) on page 3-68. Sliding Door Security Lock Your vehicle is equipped with sliding door security locks that helps prevent young children or other passengers from opening the sliding door(s) using the inside door handle. To use one of these locks, do the following: 1. Open the sliding door. 2. On the inside of the sliding door(s), on the front edge of the door will be a lock. Push the lever up to engage the lock. 3. Close the door. 4. Repeat Steps 1 through 3 for the other door. 2-15 Power Sliding Door (PSD) If your vehicle has this feature, you can open and close the power sliding door(s) using the switches inside your vehicle. You can also operate the sliding door(s) with your remote keyless entry transmitter. See Remote Keyless Entry System on page 2-4. {CAUTION: Leaving your children or pets unattended in your vehicle can be dangerous. They could operate the power sliding door. A child or others could be injured. Do not leave children or pets unattended in your vehicle. If your vehicle has power sliding door(s), you can prevent power opening of the sliding door from the passenger power sliding door (psd) activation switch by pressing the psd second row passenger override (deactivation) switch located on the overhead console. See Power Sliding Door (PSD) on page 2-16. If you want to open the sliding door while the security lock is on, unlock and open the door from the outside. You should let adults and older children know how the security lock works, and how to cancel the lock. If you do not, adults or older children who ride in the rear will not be able to open the sliding door from the inside while the security lock feature is in use. Canceling the Sliding Door Security Lock 1. Unlock the sliding door and open the door from the outside. 2. Push the security lock lever all the way down. 3. Close the door. 4. Repeat Steps 1 through 3 for the other door. The sliding door lock will now work normally. 2-16 Power Sliding Door (PSD) Switches Your vehicle will have one of the following sets of switches located on the overhead console switchbank. If your vehicle has a single power sliding door (PSD), you have these switches. Your vehicle also has passenger power sliding door activation switch(es). PSD Activation Switch PSD Second Row Passenger Override (Deactivation) Switch If your vehicle has dual power sliding doors, you have these switches. The PSD activation and PSD second row passenger override (deactivation) is one switch. Driver’s Side and Passenger’s Side PSD Switches Passenger PSD Activation Switch If you have a single PSD, this switch is located in front of the passenger side sliding door. If your vehicle has dual PSDs, the switches are located in front of both sliding doors. 2-17 Power Sliding Door Operation The power sliding door(s) will only open if the transaxle is in PARK (P). The transaxle does not have to be in PARK (P) to close the door(s). There are several ways to open and close the power sliding door(s). If your vehicle has a single power sliding door, press the bottom of the overhead console PSD activation switch. If your vehicle has dual power sliding doors, press the top of the driver’s side and/or passenger’s side overhead console PSD switch. (cid:127) Press the passenger PSD activation switch. This switch will also stop a moving door immediately. (cid:127) Press the power sliding door button on the remote keyless entry transmitter. To manually open the power sliding door(s) while the switch(es) are in the activation position, pull and release the inside or outside door handle to release the door latch. The door will fully open. To manually close the power sliding door(s) while the switches are in the activation position, pull the inside or outside door handle or the edge of the door. Move the door about 4 inches (10 cm) toward the closed position and release it. The door will close completely and latch. If a power sliding door is locked, it cannot be unlocked and opened using the overhead console PSD activation switch(es) or the passenger PSD activation switch(es). The power sliding door must either be manually unlocked or unlocked using the power door unlock switch located on the driver’s or front passenger’s armrest, and then opened using the overhead or passenger PSD activation switch(es). The remote keyless entry transmitter can also be used to open the power sliding door(s). If the vehicle is locked, press the power sliding door button(s) and all doors will unlock and the sliding door(s) will open. See Remote Keyless Entry System Operation on page 2-5. If the power sliding door has been manually locked, you must unlock the PSD before it can be opened. 2-18 (cid:127) (cid:127) (cid:127) (cid:127) If you leave the power sliding door on Notice: when you go through an automatic car wash, the door may accidentally open. Be sure the power sliding door is turned off when going through a car wash. If the power sliding door(s) is open or in the process of closing when you shift out of PARK (P), a chime will sound. This is a warning that the sliding door(s) is not completely closed. Also, the Driver Information Center (DIC) will indicate if the door is open. See DIC Warnings and Messages on page 3-51. Stop the vehicle and close the door. {CAUTION: If you shift the transaxle out of PARK (P) and accelerate before the power sliding door latches closed, the door may reverse to the open position. A child or others could fall out of the vehicle and be injured. Always make sure the power sliding door is closed and latched before you drive away. If an object obstructs the power sliding door(s) while it is closing, the door will automatically reverse to the open position, provided it meets sufficient resistance. Resistance must be as strong as the force of the closing door, or stronger. The force of the closing door increases signiﬁcantly as the door approaches the latched position. 2-19 The driver’s side sliding door is designed to open only a little if the fuel door is open. If this ever happens, do not try to force the sliding door. When the fuel ﬁller door is closed, the driver’s side sliding door can be opened normally. {CAUTION: You or others could be injured if caught in the path of the sliding door. Make sure the door path is clear before closing the door. 2-20 {CAUTION: If your vehicle is facing downward on a steep grade (15 percent or more), the door may not stay open and could slam shut, possibly injuring someone. To make sure the door does not slam shut, turn on the power sliding door feature. Then if the door closes, it will close under the control of the power door system. Power Sliding Door Second Row Passenger Override (Deactivation) To help avoid accidental operation of the sliding door(s) by using the passenger PSD activation switch, press the overhead console deactivation switch. The door can still be manually opened from the inside or outside with the override (deactivation) switch on. To open a power sliding door(s) manually when the overhead console switch is in override (deactivation) position, pull the inside or outside door handle and slide the door all the way back. To close the door(s) manually when the override switch(es) is in the override (deactivation) position, pull the inside or outside door handle and slide the door all the way forward to the latched position. To stop the door(s) immediately while the door(s) is opening or closing, press the bottom of the PSD override (deactivation) switch. Pressing the PSD button(s) on the remote keyless entry will open and close the door unless the door has been manually locked using the mechanical slider. Resetting the Power Sliding Door The power sliding door may operate incorrectly or not at all because of the following conditions: (cid:127) A low voltage or dead battery (cid:127) A disconnected battery If the instrument panel PSD/fuse 21, LHPSD/fuse 24 or RHPSD/fuse 25 are removed or blown. See Fuses and Circuit Breakers on page 5-87 for more information about your fuse panel. 2-21 (cid:127) If any of these conditions occur, the power sliding door may need to be reset. If your vehicle has the dual power sliding doors, both doors will have to be reset. To reset a door, do the following: 1. Check to be sure the power sliding door is unlocked and securely closed. 2. Turn the ignition to LOCK. 3. If the power sliding door overhead console switch is in the override (deactivation) position, return to the activation position. 4. Open the sliding door using the remote keyless entry transmitter, overhead console switch, or passenger switch. Allow the door to travel fully open. If the door does not travel to the fully open position, press the overhead console switch to the override (deactivation) position and slide the door fully open and closed. Check for foreign objects in the tracks. Repeat the procedure starting with Step 1. If the door resists travel to the fully open position, see your dealer for service. Liftgate To unlock or lock the liftgate from the outside, use the remote keyless entry transmitter. For more information, see Remote Keyless Entry System Operation on page 2-5. You can also use the power door lock switch to lock and unlock the liftgate. Open the liftgate using the handle located above the license plate. Once slightly opened, the liftgate will rise by itself. Lamps in the rear of the vehicle will come on, illuminating the rear cargo area. Notice: for overhead obstructions such as a garage door, you could break the liftgate glass. Always check to make sure the area above the liftgate is clear before opening it. If you open the liftgate without checking 2-22 {CAUTION: It can be dangerous to drive with the liftgate open because carbon monoxide (CO) gas can come into your vehicle. You can’t see or smell CO. It can cause unconsciousness and even death. If you must drive with the liftgate open or if electrical wiring or other cable connections must pass through the seal between the body and the liftgate: (cid:127) Make sure all other windows are shut. (cid:127) Turn the fan on your heating or cooling system to its highest speed and select the control setting that will force outside air into your vehicle. See Dual Climate Control System on page 3-25. If you have air outlets on or under the instrument panel, open them all the way. See Engine Exhaust on page 2-40. To close the liftgate, pull down on the handle, then ﬁrmly shut the liftgate. Do not drive with the liftgate open, even slightly. 2-23 (cid:127) Windows {CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather. 2-24 Power Windows Power Rear Quarter Windows Your vehicle has power rear quarter windows. This switch, located in the overhead console switchbank, is used for opening and closing the power rear quarter windows. The switches on the driver’s door armrest control the front windows when the ignition is in RUN, ACCESSORY or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 2-31. The driver’s power window switch has two down positions. The ﬁrst position lowers the window normally. To raise the window, pull up the front of the switch. Express-Down Window To activate the express-down feature, push the AUTO switch all the way down to the second position, then release it. The window will lower completely. To stop the window from lowering all the way, pull up on the front of the switch. Press the top of the switch to open the windows; both windows will open. The windows will continue to open as long as the switch is pressed, until they are fully opened. Press the bottom of the switch with the symbol to close both windows. The windows can be closed fully or partially, depending on how long the switch is pressed. The ignition must be in RUN, ACCESSORY, or Retained Accessory Power (RAP) must be active, to use the power rear quarter windows. See Retained Accessory Power (RAP) on page 2-31. 2-25 Sun Visors To block out glare, you can swing down the visors and slide them along the rod to cover different areas of the front window. You can also remove them from the center mount and swing them to the side. Lighted Vanity Mirror Your vehicle has lighted vanity mirrors. Pull down the sun visor and ﬂip up the cover to expose the vanity mirror. The lamps will come on when you ﬂip up the cover. Theft-Deterrent Systems Vehicle theft is big business, especially in some cities. Although your vehicle has a number of theft-deterrent features, we know that nothing we put on it can make it impossible to steal. 2-26 Content Theft-Deterrent Your vehicle has a theft-deterrent alarm system. A light located on top of your instrument panel, near the center of the vehicle next to the windshield, will ﬂash slowly to let you know that the system has been armed. While armed, the doors will not unlock with the power door lock switch. Once armed, the alarm will go off if someone tries to enter the vehicle without using the remote keyless entry transmitter or a key, or turns the ignition to RUN. The horn will sound and the turn signal lamps will ﬂash for up to two minutes. Arming with the Power Lock Switch Your alarm system will arm when the key is removed from the ignition and you use the driver’s power door lock switch, with the driver’s door open or the passenger’s door power door lock switch with the passenger’s door open to lock the vehicle. If you would like to turn on power door lock switch arming, see DIC Vehicle Personalization (Uplevel Only) on page 3-68 When the security light ﬂashes quickly the system is arming. After all doors and the liftgate are closed and locked, the security light will begin ﬂashing at a very slow rate to let you know the system is armed. Arming with the Remote Keyless Entry Transmitter Your alarm system will arm if the key is not in the ignition and you use your remote keyless entry transmitter to lock the doors. The security light will ﬂash to let you know the system is arming. After all doors and the liftgate are closed and locked, the security light will begin ﬂashing at a very slow rate to let you know the system is armed. Arming with Your Key Your alarm system will arm when you use your key to lock the driver’s door. The security light will ﬂash to let you know the system is arming. After all doors and the liftgate are closed and locked, the security light will begin ﬂashing at a very slow rate to let you know the system is armed. If you would like your key not to arm the system, see DIC Vehicle Personalization (Uplevel Only) on page 3-68. Arming Conﬁrmation If remote unlock conﬁrmation is on, the turn signal lamps will ﬂash brieﬂy to let you know when your alarm system has disarmed. If you would not like the turn signal lamps to ﬂash, see DIC Vehicle Personalization (Uplevel Only) on page 3-68. Disarming with the Remote Keyless Entry Transmitter Your alarm system will disarm when you use your remote keyless entry transmitter to unlock the doors. The security light will stop ﬂashing to let you know the system is no longer armed. 2-27 Disarming with Your Key Your alarm system will disarm when you use your key to unlock the driver’s door. The security light will stop ﬂashing to let you know the system is no longer armed. If you would like your key not to disarm the alarm system, see DIC Vehicle Personalization (Uplevel Only) on page 3-68. PASS-Key® III Your PASS-Key® III system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. 2-28 Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. PASS-Key® III uses a radio frequency transponder in the key that matches a decoder in your vehicle. PASS-Key® III Operation Your vehicle is equipped with the PASS-Key® III (Personalized Automotive Security System) theft-deterrent system. PASS-Key® III is a passive theft deterrent system. This means you do not have to do anything different to arm or disarm the system. It works when you insert or remove the key from the ignition. When the PASS-Key® III system senses that someone is using the wrong key, it shuts down the vehicle’s starter and fuel systems. The starter will not work and fuel will stop being delivered to the engine. Anyone using a trial-and-error method to start the vehicle will be discouraged because of the high number of electrical key codes. If the engine does not start and the security message comes on, the key may have a damaged transponder. Turn the ignition off and try again. If the engine still does not start, and the key appears to be undamaged, try another ignition key. At this time, you may also want to check the instrument panel PASS KEY fuse. If the engine still does not start with the other key, your vehicle needs service. If your vehicle does start, the ﬁrst key may be faulty. See your dealer or a locksmith who can service the PASS-Key® III to have a new key made. See Fuses and Circuit Breakers on page 5-87. It is possible for the PASS-Key® III decoder to learn the transponder value of a new or replacement key. Up to 10 keys may be programmed for the vehicle. This procedure is for learning additional keys only. If all the currently programmed keys are lost or do not operate, you must see your dealer or a locksmith who can service PASS-Key® III to have keys made and programmed to the system. See your dealer or a locksmith who can service PASS-Key® III to get a new key blank that is cut exactly as the ignition key that operates the system. To program the new key, do the following: 1. Verify the new key has PK3 stamped on it. 2. Insert the original, already programmed key into the ignition lock cylinder and start the engine. If the engine will not start, see your dealer for service. 3. After the engine has started, turn the key to OFF and remove the key. 4. Insert the key to be programmed and turn it to RUN within 10 seconds of removing the previous key. 5. The security message will turn off once the key has been programmed. It may not be apparent that the security message went on due to how quickly the key is programmed. 6. Repeat Steps 1 through 4 if additional keys are to be programmed. If you are ever driving and the security message comes on and stays on, you will be able to restart your engine if you turn it off. Your PASS-Key® III system, however, is not working properly and must be serviced by your dealer. Your vehicle is not protected by the PASS-Key® III system at this time. If you lose or damage a PASS-Key® III key, see your dealer or a locksmith who can service PASS-Key® III to have a new key made. 2-29 Ignition Positions The key can be turned to one of four positions while in the ignition switch. A (LOCK): This is the only position from which you can remove the key. This position locks your ignition and transaxle. Starting and Operating Your Vehicle New Vehicle Break-In Notice: Your vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: (cid:127) Do not drive at any one speed, fast or slow, for the ﬁrst 500 miles (805 km). Do not make full-throttle starts. (cid:127) Avoid making hard stops for the ﬁrst 200 miles (322 km) or so. During this time your new brake linings are not yet broken in. Hard stops with new linings can mean premature wear and earlier replacement. Follow this breaking-in guideline every time you get new brake linings. (cid:127) Do not tow a trailer during break-in. See Towing a Trailer on page 4-39 for more information. 2-30 Notice: Using a tool to force the key from the ignition switch could cause damage or break the key. Use the correct key and turn the key only with your hand. Make sure the key is all the way in. If none of this works, then your vehicle needs service. B (ACCESSORY): This is the position in which you can operate the electrical accessories, such as the radio. C (RUN): This is the position to which the switch returns after the engine is started and the ignition key is released. This is the position for driving. Even while the engine is not running, RUN can be used to operate your electrical accessories and to display some instrument panel warning lights. D (START): This position starts the engine. When the engine starts, release the ignition key. The switch will return to RUN for driving. Retained Accessory Power (RAP) With RAP, your power windows and the audio system will continue to work for up to 10 minutes after the engine is turned off or until either door is opened. If a door is opened, the power windows and audio system will shut off. Starting the Engine Move your shift lever to PARK (P) or NEUTRAL (N). Your engine will not start in any other position — that is a safety feature. To restart when you are already moving, use NEUTRAL (N) only. Notice: Shifting into PARK (P) with the vehicle moving could damage the transaxle. Shift into PARK (P) only when your vehicle is stopped. 1. With your foot off the accelerator pedal, turn your ignition key to START. When the engine starts, let go of the key. The idle speed will go down as your engine warms up. Notice: Holding your key in START for longer than 15 seconds at a time will cause your battery to be drained much sooner. And the excessive heat can damage your starter motor. Wait about 15 seconds between each try to help avoid draining your battery or damaging your starter. 2. If the engine does not start in 10 seconds, push the accelerator pedal about one-quarter of the way down while you turn the key to START. Do this until the engine starts. As soon as it does, let go of the key. 2-31 3. If your engine still will not start, or starts but then stops, it could be ﬂooded with too much gasoline. Try pushing your accelerator pedal all the way to the ﬂoor and holding it there as you hold the key in START for a maximum of 15 seconds. This clears the extra gasoline from the engine. If the engine still will not start, or starts brieﬂy but then stops again, repeat Step 1 or 2, depending on the temperature. When the engine starts, release the key and the accelerator pedal. Notice: Your engine is designed to work with the electronics in your vehicle. If you add electrical parts or accessories, you could change the way the engine operates. Before adding electrical equipment, check with your dealer. If you do not, your engine might not perform properly. Engine Coolant Heater Your vehicle may have an engine coolant heater. In very cold weather, 0°F (−18°C) or colder, the engine coolant heater can help. You will get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle. At temperatures above 32°F (0°C), use of the coolant heater is not required. Your vehicle may also have an internal thermostat in the plug end of the cord. This will prevent operation of the engine coolant heater when the temperature is at or above 0°F (−18°C) as noted on the cord. To Use the Engine Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. The electrical cord is located on the driver’s side of the engine compartment. 3. Plug it into a normal, grounded 110-volt AC outlet. 2-32 {CAUTION: Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a ﬁre. You could be seriously injured. Plug the cord into a properly grounded three-prong 110-volt AC outlet. If the cord will not reach, use a heavy-duty three-prong extension cord rated for at least 15 amps. 4. Before starting the engine, be sure to unplug and store the cord as it was before to keep it away from moving engine parts. If you do not, it could be damaged. How long should you keep the coolant heater plugged in? The answer depends on the outside temperature, the kind of oil you have, and some other things. Instead of trying to list everything here, we ask that you contact your Saturn retailer in the area where you will be parking your vehicle. The Saturn retailer can give you the best advice for that particular area. Automatic Transaxle Operation Maximum engine speed is limited when you are in PARK (P) or NEUTRAL (N), to protect driveline components from improper operation. There are several different positions for your shift lever. PARK (P): This gear position locks your front wheels. It is the best position to use when you start your engine because your vehicle cannot move easily. Ensure the shift lever is fully in PARK (P) before starting the engine. Your vehicle has an automatic transaxle shift lock control system. You have to fully apply your regular brakes before you can shift from PARK (P) when the ignition key is in RUN. As you step on the brake pedal while in PARK (P), you may hear a click from the solenoid of the system. This ensures that the system is operating properly. 2-33 If you cannot shift out of PARK (P), ease pressure on the shift lever — push the shift lever all the way into PARK (P) as you maintain brake application. Then move the shift lever into the gear you wish. See Shifting Out of Park (P) on page 2-39. {CAUTION: It is dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set your parking brake and move the shift lever to PARK (P). See Shifting Into Park (P) on page 2-38. If you are pulling a trailer, see Towing a Trailer on page 4-39. REVERSE (R): Use this gear to back up. Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transaxle. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped. To rock your vehicle back and forth to get out of snow, ice or sand without damaging your transaxle, see If Your Vehicle is Stuck in Sand, Mud, Ice or Snow on page 4-31. NEUTRAL (N): In this position, your engine does not connect with the wheels. To restart when you are already moving, use NEUTRAL (N) only. Also, use NEUTRAL (N) when your vehicle is being towed. {CAUTION: Shifting into a drive gear while your engine is running at high speed is dangerous. Unless your foot is ﬁrmly on the brake pedal, your vehicle could move very rapidly. You could lose control and hit people or objects. Do not shift into a drive gear while your engine is running at high speed. 2-34 Notice: Shifting out of PARK (P) or NEUTRAL (N) while the engine is running at high speed may damage the transaxle. The repairs would not be covered by your warranty. Be sure the engine is not running at high speeds when shifting your vehicle. AUTOMATIC OVERDRIVE (D): This position is for normal driving. If you need more power for passing, and you are: (cid:127) Going less than 35 mph (55 km/h), push your accelerator pedal about halfway down. (cid:127) Going about 35 mph (55 km/h) or more, push the accelerator all the way down. If your vehicle seems to start up rather You will shift down to the next gear and have more power. Notice: slowly or not shift gears when you go faster, and you continue to drive your vehicle that way, you could damage the transaxle. Have your vehicle serviced right away. You can drive in SECOND (2) when you are driving less than 35 mph (55 km/h) and AUTOMATIC OVERDRIVE (D) for higher speeds until then. Warm-Up Shift Your vehicle has a computer controlled transaxle designed to warm up the engine faster when the outside temperature is 35°F (2°C) or colder. You may notice that the transaxle will shift at a higher vehicle speed until the engine is warmed up. This is a normal condition designed to provide heat to the passenger compartment and defrost the windows more quickly. See Dual Climate Control System on page 3-25 for more information. THIRD (3): This position is also used for normal driving, but it offers more power and lower fuel economy than AUTOMATIC OVERDRIVE (D). Here are some times you might choose THIRD (3) instead of AUTOMATIC OVERDRIVE (D): (cid:127) When driving on hilly, winding roads (cid:127) When towing a trailer, so there is less shifting between gears (cid:127) When going down a steep hill 2-35 Notice: Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transaxle. If you are stuck, do not spin the tires. When stopping on a hill, use the brakes to hold the vehicle in place. All-Wheel Drive If your vehicle has all-wheel drive, your engine’s driving power is sent to all four wheels for extra traction when needed. This is like four-wheel drive, but there is no separate lever or switch to engage or disengage the front axle. It is fully automatic, and adjusts itself as needed for road conditions. You may experience a brief vehicle vibration upon acceleration when driving in slippery conditions. This is normal and is an indication that the all-wheel drive system is functioning properly. See All-Wheel Drive (AWD) System on page 4-12 for more information. SECOND (2): This position gives you more power but lower fuel economy than THIRD (3). You can use SECOND (2) on hills. It can help control your speed as you go down steep mountain roads, but then you would also want to use your brakes off and on. Notice: Driving in SECOND (2) for more than 25 miles (40 km) or at speeds over 55 mph (90 km/h) may damage the transaxle. Also, shifting into SECOND (2) at speeds above 65 mph (105 km/h) can cause damage. Drive in THIRD (3) or AUTOMATIC OVERDRIVE (D) instead of SECOND (2). Notice: slowly, or if it seems not to shift gears as you go faster, something may be wrong with a transaxle system sensor. If you drive very far that way, your vehicle can be damaged. So, if this happens, have your vehicle serviced right away. Until then, you can use SECOND (2) when you are driving less than 35 mph (55 km/h) and THIRD (3) for higher speeds. If your vehicle seems to start up rather FIRST (1): This position gives you even more power but lower fuel economy than SECOND (2). You can use it on very steep hills, or in deep snow or mud. If the shift lever is put in FIRST (1), the transaxle will not downshift into ﬁrst gear until the vehicle is going slow enough. 2-36 Parking Brake The parking brake is located under the instrument panel on the driver’s side of the vehicle. To release the parking brake, hold the regular brake pedal down with your right foot while you push down on the parking brake pedal with your left foot. When you lift your left foot from the parking brake pedal, it will pop up to the released position. Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Verify that the parking brake is fully released and the brake warning light is off before driving. If you are towing a trailer and are parking on any hill, see Towing a Trailer on page 4-39. To set the parking brake, hold the regular brake pedal down with your right foot and push down on the parking brake pedal with your left foot. If the ignition is on, the brake system warning light will come on. See Brake System Warning Light on page 3-37. 2-37 Shifting Into Park (P) {CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, use the steps that follow. If you are pulling a trailer, see Towing a Trailer on page 4-39. 1. Hold the brake pedal down with your right foot and set the parking brake with your left foot. 2. Move the shift lever into PARK (P) by pulling the shift lever toward you and moving it up as far as it will go. 3. Turn the ignition key to LOCK. 4. Remove the key and take it with you. If you can leave your vehicle with the ignition key in your hand, your vehicle is in PARK (P). 2-38 Leaving Your Vehicle With the Engine Running {CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch ﬁre. You or others could be injured. Do not leave your vehicle with the engine running. If you have to leave your vehicle with the engine running, be sure your vehicle is in PARK (P) and the parking brake is ﬁrmly set before you leave it. After you move the shift lever into PARK (P), hold the regular brake pedal down. Then, see if you can move the shift lever away from PARK (P) without ﬁrst pulling it toward you. If you can, it means that the shift lever was not fully locked into PARK (P). Torque Lock If you are parking on a hill and you do not shift your vehicle into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transaxle. You may ﬁnd it difficult to pull the shift lever out of PARK (P). This is called torque lock. To prevent torque lock, set the parking brake and then shift into PARK (P) properly before you leave the driver’s seat. To ﬁnd out how, see Shifting Into Park (P) on page 2-38. When you are ready to drive, move the shift lever out of PARK (P) before you release the parking brake. If torque lock does occur, you may need to have another vehicle push yours a little uphill to take some of the pressure from the parking pawl in the transaxle, so you can pull the shift lever out of PARK (P). Shifting Out of Park (P) Your vehicle has an automatic transaxle shift lock control system which locks the shift lever in PARK (P) when the ignition is in the LOCK position. In addition, you must fully apply your regular brakes before you can shift from PARK (P) when the ignition is in RUN. See Automatic Transaxle Operation on page 2-33. Parking Over Things That Burn {CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass or other things that can burn. 2-39 Running the Engine While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. {CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. See the earlier caution under Engine Exhaust on page 2-40. Also, idling in a closed-in place can let deadly carbon monoxide (CO) into your vehicle even if the climate control fan is at the highest setting. One place this can happen is a garage. Exhaust — with CO — can come in easily. NEVER park in a garage with the engine running. Another closed-in place can be a blizzard. See Winter Driving on page 4-27. Engine Exhaust {CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: (cid:127) Your exhaust system sounds strange or different. (cid:127) Your vehicle gets rusty underneath. (cid:127) Your vehicle was damaged in a collision. (cid:127) Your vehicle was damaged when driving over high points on the road or over road debris. (cid:127) Repairs were not done correctly. (cid:127) Your vehicle or exhaust system had been modiﬁed improperly. If you ever suspect exhaust is coming into your vehicle: (cid:127) Drive it only with all the windows down to blow out any CO; and (cid:127) Have your vehicle ﬁxed immediately. 2-40 {CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set your parking brake and move the shift lever to PARK (P). Follow the proper steps to be sure your vehicle will not move. See Shifting Into Park (P) on page 2-38. If you are pulling a trailer, see Towing a Trailer on page 4-39. Mirrors Manual Rearview Mirror While sitting in a comfortable driving position, adjust the mirror so you can see clearly behind your vehicle. Grip the mirror in the center to move it up or down and side to side. The day/night adjustment can lessen glare from the headlamps behind your vehicle. Pull the tab forward for daytime use; push it back for night use. Outside Power Mirrors The controls, located on the driver’s door, operate both outside rearview mirrors. Push the top control to the left or right to choose either the driver’s or passenger’s outside rearview mirror. Leave the control in the center position to prevent moving the mirrors once they are adjusted. 2-41 Use the arrows on the bottom control to adjust the position of each mirror. Adjust each mirror so that you can see the side of your vehicle and the area behind it, while sitting in a comfortable driving position. Both outside mirrors can be folded forward or rearward to prevent damage when going through car washes or conﬁned spaces. Outside Convex Mirror {CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes. The passenger’s side mirror is convex. A convex mirror’s surface is curved so more can be seen from the driver’s seat. It also makes things appear farther away than they really are. Outside Heated Mirrors The outside rearview mirrors will heat to help clear them of ice, snow, and condensation when the rear window defogger is turned on. See “Rear Window Defogger” in Dual Climate Control System on page 3-25. OnStar® System OnStar® uses global positioning system (GPS) satellite technology, wireless communications, and call centers to provide you with a wide range of safety, security, information, and convenience services. A complete OnStar® user’s guide and the terms and conditions of the OnStar® Subscription Service Agreement are included in the vehicle’s glove box literature. For more information, visit www.onstar.com or www.onstarcanada.com. Contact OnStar® at 1-888-4-ONSTAR (1-888-466-7827), or press the OnStar® button to speak to an OnStar® advisor 24 hours a day, 7 days a week. Terms and conditions of the Subscription Service Agreement can be found at www.onstar.com or www.onstarcanada.com. 2-42 OnStar® Services For new vehicles equipped with OnStar®, the Safe and Sound Plan is included for the ﬁrst year. You can extend this plan beyond the ﬁrst year, or upgrade to the Directions and Connections Plan to meet your needs. For more information, press the OnStar® button to speak with an advisor. Safe and Sound Plan (cid:127) Automatic Notiﬁcation of Airbag Deployment (cid:127) Emergency Services (cid:127) Roadside Assistance (cid:127) Stolen Vehicle Tracking (cid:127) AccidentAssist (cid:127) Remote Door Unlock/Vehicle Alert (cid:127) Remote Diagnostics (cid:127) Online Concierge Directions and Connections Plan (cid:127) All Safe and Sound Plan Services (cid:127) Driving Directions (cid:127) RideAssist Information and Convenience Services OnStar® Personal Calling As an OnStar® subscriber, the Personal Calling capability is available if your hand-held cell phone is lost, forgotten, or has a low battery. It is a hands-free wireless phone that is integrated into the vehicle. Calls can be placed nationwide using simple voice commands with no additional contracts and no additional roaming charges. To ﬁnd out more about OnStar® Personal Calling, refer to the OnStar® user’s guide in the vehicle’s glove box or visit www.onstar.com or www.onstarcanada.com; or speak with an OnStar® advisor by pressing the OnStar® button or by calling 1-888-4-ONSTAR (1-888-466-7827). OnStar® Virtual Advisor Virtual Advisor is a feature of OnStar® Personal Calling that uses minutes to access up-to-date weather and traffic reports for your area, news and sports updates, stock quotes, entertainment and more. Customize your information proﬁle at www.myonstar.com. See the OnStar® user’s guide for more information. 2-43 (cid:127) HomeLink® complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes and modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. HomeLink® Wireless Control System HomeLink®, a combined universal transmitter and receiver, provides a way to replace up to three hand-held transmitters used to activate devices such as gate operators, garage door openers, entry door locks, security systems and home lighting. Additional HomeLink® information can be found on the Internet at www.homelink.com or by calling 1-800-355-3515. 2-44 HomeLink® Wireless Control System Operation Do not use the HomeLink® Transmitter with any garage door opener that does not have the “stop and reverse” feature. This includes any garage door opener model manufactured before April 1, 1982. If you have a newer garage door opener with rolling codes, please be sure to follow Steps 6 through 8 to complete the programming of your HomeLink® Transmitter. Read the instructions completely before attempting to program the HomeLink® Transmitter. Because of the steps involved, it may be helpful to have another person available to assist you in programming the transmitter. Keep the original transmitter for use in other vehicles as well as for future HomeLink® programming. It is also recommended that upon the sale of the vehicle, the programmed HomeLink® buttons should be erased for security purposes. Refer to “Erasing HomeLink® Buttons” or, for assistance, contact HomeLink® on the Internet at: www.homelink.com or by calling 1-800-355-3515. Be sure that people and objects are clear of the garage door or gate operator you are programming. When programming a garage door, it is advised to park outside of the garage. It is recommended that a new battery be installed in your hand-held transmitter for quicker and more accurate transmission of the radio frequency. Programming HomeLink® Your vehicle’s engine should be turned off while programming the transmitter. Follow these steps to program up to three channels: 1. Press and hold down the two outside buttons, releasing only when the indicator light begins to ﬂash, after 20 seconds. Do not hold down the buttons for longer than 30 seconds and do not repeat this step to program a second and/or third transmitter to the remaining two HomeLink® buttons. 2. Position the end of your hand-held transmitter about 1 to 3 inches (3 to 8 cm) away from the HomeLink® buttons while keeping the indicator light in view. 2-45 6. Locate in the garage, the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. 7. Firmly press and release the “Learn” or “Smart” button. The name and color of the button may vary by manufacturer. You will have 30 seconds to start Step 8. 8. Return to the vehicle. Firmly press and hold the programmed HomeLink® button for two seconds, then release. Repeat the press/hold/release sequence a second time, and depending on the brand of the garage door opener (or other rolling code device), repeat this sequence a third time to complete the programming. HomeLink® should now activate your rolling-code equipped device. To program the remaining two HomeLink® buttons, begin with Step 2 of “Programming HomeLink®.” You do not want to repeat Step 1, as this will erase all previous programming. 3. Simultaneously press and hold both the desired button on HomeLink® and the hand-held transmitter button. Do not release the buttons until Step 4 has been completed. Some entry gates and garage door openers may require you to substitute Step 3 with the procedure noted in “Gate Operator and Canadian Programming” later in this section. 4. The indicator light will ﬂash slowly at ﬁrst and then rapidly after HomeLink® successfully receives the frequency signal from the hand-held transmitter. Release both buttons. 5. Press and hold the newly-trained HomeLink® button and observe the indicator light. If the indicator light stays on constantly, programming is complete and your device should activate when the HomeLink® button is pressed and released. To program the remaining two HomeLink® buttons, begin with Step 2 under “Programming HomeLink®.” Do not repeat Step 1 as this will erase all of the programmed channels. If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with Steps 6 through 8 following to complete the programming of a rolling-code equipped device (most commonly, a garage door opener). 2-46 Gate Operator and Canadian Programming Canadian radio-frequency laws require transmitter signals to “time out” or quit after several seconds of transmission. This may not be long enough for HomeLink® to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to “time out” in the same manner. If you live in Canada, or you are having difficulty programming a gate operator by using the “Programming HomeLink®” procedures (regardless of where you live), replace Step 3 under “Programming HomeLink®” with the following: Continue to press and hold the HomeLink® button while you press and release every two seconds (cycle) your hand-held transmitter until the frequency signal has been successfully accepted by HomeLink®. The indicator light will ﬂash slowly at ﬁrst and then rapidly. Proceed with Step 4 under “Programming HomeLink®” to complete. Using HomeLink® Press and hold the appropriate HomeLink® button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing HomeLink® Buttons To erase programming from the three buttons do the following: 1. Press and hold down the two outside buttons until the indicator light begins to ﬂash, after 20 seconds. Do not hold the two outside buttons for longer than 30 seconds. 2. Release both buttons. HomeLink® is now in the train (learning) mode and can be programmed at any time beginning with Step 2 under “Programming HomeLink®” shown earlier in this section. Individual buttons cannot be erased, but they can be reprogrammed. See “Reprogramming a Single HomeLink® Button” following this section. 2-47 Reprogramming a Single HomeLink® Button To program a device to HomeLink® using a HomeLink® button previously trained, follow these steps: 1. Press and hold the desired HomeLink® button. Do not release the button. 2. The indicator light will begin to ﬂash after 20 seconds. While still holding the HomeLink® button, proceed with Step 2 under “Programming HomeLink®” shown earlier in this section. Resetting Defaults To reset HomeLink® to default settings do the following: 1. Hold down the two outside buttons for about 20 seconds until the indicator light begins to ﬂash. 2. Continue to hold both buttons until the HomeLink® indicator light turns off. 3. Release both buttons. For questions or comments, contact HomeLink® at 1-800-355-3515, or on the Internet at www.homelink.com. Storage Areas Your vehicle’s large carrying capacity can store many items. If the vehicle has an extended wheelbase, it can carry even larger items. The ﬂoor pins that are used to attach the seats, can be used to secure larger loads. There may be additional storage areas behind the seats. Glove Box If the glove box has a lock, put your key into the lock and turn the key counterclockwise. To open the glove box, pull the latch release. The glove box door has a detent to prevent the door from lowering too far. Open the glove box until the door is partway open, then pull the door down if you need it fully opened. To close the glove box, the door must be pushed up past the detent. To lock the glove box, put your key into the lock and turn the key clockwise. 2-48 Cupholder(s) There are cupholders located below the center instrument panel switchbank. The cupholders have a rubber liner that can be removed, so that larger cups can ﬁt into the cupholders. You can also remove the liner to clean it. To use the cupholders, pull the tray out. Push the tray back when not in use. Storage Bin Your vehicle may have a storage bin located on the overhead rail that you can use for storage. Overhead Console (With Rail) If your vehicle is equipped with an overhead console, it may contain the following: (cid:127) Reading lamps. See Front Reading Lamps on page 3-19 or Rear Reading Lamps on page 3-19. (cid:127) Switchbank. See Overhead Console Switchbank on page 3-20. (cid:127) OnStar® System buttons. See OnStar® System on page 2-42. (cid:127) Driver Information Center (DIC). See Driver Information Center (DIC) on page 3-45. (cid:127) HomeLink® Transmitter buttons. See HomeLink® Wireless Control System on page 2-44. 1. Place the storage bin on to the rails in the desired location. 2. Push ﬁrmly upward on the bin while supporting it with one hand. 3. Push in on the latch and then rotate it 90 degrees. 2-49 The contents of the bin should never weigh more than 1.5 lbs (0.7 kg). Always make sure to close and latch the bin before driving. Overhead Console (Without Rail) If your vehicle has an overhead console without the rail system, it has two reading lights, a courtesy light, and a switchbank. See Overhead Console Switchbank on page 3-20 for more information. Floor Console Storage Area If your vehicle has a storage compartment located on the front console below the front cupholders. Pull up and then forward on the handle to open the storage compartment. 4. Firmly press down making sure the latch is ﬂat with the ribs (A) on the storage bin. 5. Switch hands and repeat Steps 2 through 4 for the latch on the opposite side of the storage bin. 6. Reverse these steps in order to remove the storage bin. 2-50 Folding Tray Your vehicle may be equipped with folding convenience trays located between seats. To use each tray lift up on the handle located on its front end, while pulling up on the tray to lock it into place. There are four cupholders on each tray. Luggage Carrier {CAUTION: If you try to carry something on top of your vehicle that is longer or wider than the luggage carrier — like paneling, plywood, a mattress and so forth — the wind can catch it as you drive along. This can cause you to lose control. What you are carrying could be violently torn off, and this could cause you or other drivers to have a collision, and of course damage your vehicle. You may be able to carry something like this inside. But, never carry something longer or wider than the luggage carrier on top of your vehicle. If you have the luggage carrier, you can load things on top of your vehicle. Notice: Loading cargo on the luggage carrier that weighs more than 150 lbs (68 kg) or hangs over the rear or sides of the vehicle may damage your vehicle. Load cargo so that it rests on the slats as far forward as possible and against the side rails, making sure to fasten it securely. 2-51 Don’t exceed the maximum vehicle capacity when loading your vehicle. For more information on vehicle capacity and loading, see Loading Your Vehicle on page 4-32. To prevent damage or loss of cargo as you’re driving, check now and then to make sure the cargo is still securely fastened. Convenience Net (With Rear Convenience Center) Your vehicle may have a convenience net. The convenience net is designed to help keep small loads, from falling out of the vehicle when the liftgate is opened. Install the convenience net at the rear of your vehicle, inside the liftgate. To use the convenience net, do the following: 1. Attach the upper loops to the posts on both sides of the liftgate opening. The label on the net should be in the upper left corner. 2. Attach the lower loops to the tabs at the rear edge of the rear convenience center. When not in use, it is recommended that you take down the convenience net to extend the life of the net and to help retain its elasticity, and to keep the rear exit clear. 2-52 Convenience Net (Without Rear Convenience Center) Your vehicle may have a convenience net. The convenience net is designed to help keep small loads, like grocery bags, from falling over. Install the convenience net at the rear of your vehicle, inside the liftgate. To use the convenience net, do the following: 1. Attach the upper loops to the posts on both sides of the liftgate opening. The label on the net should be in the upper left corner. 2. Attach the lower hooks to the metal rings on the ﬂoor. 3. Once you have loaded items into the net, stretch the higher side of the net up and over the top of the load to hold it ﬁrmly in place. The convenience net has a maximum capacity of 100 lbs (45 kg). It is not designed to hold larger, heavier loads. Store such loads on the ﬂoor of your vehicle, as far forward as you can. When not in use, it is recommended that you take down the convenience net to extend the life of the net and to help retain its elasticity, and to keep the rear exit clear. Convenience Center {CAUTION: If any removable convenience item is not secured properly, it can move around in a collision or sudden stop. People in the vehicle could be injured. Be sure to secure any such item properly. Your vehicle may have a convenience center. It provides extra storage space for the rear of the vehicle. To open the convenience center, pull up on the door latch located on the front of the cover. The convenience center cover has two automatic prop rods to hold it up and in place. To close the convenience center cover, you must pull one of the prop rod linkages toward you while holding onto the door latch and lower the convenience center cover to close it. Removing the Convenience Center 1. Make sure that all items are off the convenience center and that it is empty. 2. Turn the hand knob, located at the rear of the convenience center, counterclockwise until the knob is loose. 3. Lift up on the hand knob, then grip and pull up on the convenience center to remove it from the vehicle. Replacing the Convenience Center 1. Make sure the third row seat is properly installed in the vehicle. See Third Row Seat on page 1-12 for more information. If the third row seat is not in the vehicle with the convenience center, the convenience center will not be locked into the correct position in the vehicle. 2. Make sure that the convenience center is empty and closed. 3. Lift the convenience center up and into the rear of the vehicle. 2-53 4. Slide the convenience center in and align it to the rear seat. 5. Press down on the front of the convenience center so the center is aligned on the sill mounting bracket. 6. Turn the hand knob clockwise until it is tight. 7. Pull up on the convenience center to make sure it is locked into place. The cover of the convenience center can be left in its upright position while the vehicle is moving. The convenience center and the third row seat both have a maximum weight capacity of 400 lbs (181.6 kg). Notice: Overloading your vehicle may cause damage. Repairs would not be covered by your warranty. Do not overload your vehicle. Vehicle Personalization Memory Seat If your vehicle has this feature, the controls for the memory function are located on the driver’s door. These buttons are used to program and recall memory settings for the driver’s seating position. The settings for these features can be personalized for both driver 1 and driver 2. Driver 1 or driver 2 corresponds to the memory buttons labelled 1 and 2 on the driver’s door. 2-54 To store the memory settings, do the following: 1. Adjust the driver’s seat to your preference. 2. Press and hold the 1 or 2 button of the memory control for three seconds. A double chime will sound to let you know that the position has been stored. To repeat the procedure for a second driver, follow the preceding steps, but press the other numbered memory control button. To recall the memory settings, press and release button 1 or 2 while the vehicle is in PARK (P). A single chime will sound and the memory position will be recalled. To stop recall movement of the memory seat feature at any time, press one of the memory buttons or power seat controls. Easy Exit Seat The control for the easy exit seat function is located on the driver’s door below the memory buttons 1 and 2. The easy exit seat button is used to program and recall the desired driver’s seat position when exiting/entering the vehicle. The seat position can be personalized for both driver 1 and driver 2. To store the easy exit seat position for driver 1 or 2, do the following: 1. Press and release the 1 or 2 button of the memory control. The seat will move to the stored memory position. 2. Adjust the seat to the desired exit position. 3. Press and hold the easy exit seat button for three seconds. A double chime will sound to let you know that the position has been stored for the identiﬁed driver 1 or 2. To repeat the procedure for a second driver, follow the preceding steps, but press the other numbered memory control button. To recall the easy exit seat position, press the easy exit seat button on the memory control while the vehicle is in PARK (P). A singe chime will sound and the seat will move to the stored exit position. If an easy exit seat position has not been stored, the default position is all the way rearward. 2-55 ✍ NOTES 2-56 Section 3 Instrument Panel Instrument Panel Overview ...............................3-4 Hazard Warning Flashers ................................3-6 Other Warning Devices ...................................3-6 Horn .............................................................3-6 Tilt Wheel .....................................................3-6 Turn Signal/Multifunction Lever .........................3-7 Turn and Lane-Change Signals ........................3-7 Headlamp High/Low-Beam Changer ..................3-8 Flash-to-Pass .................................................3-8 Windshield Wipers ..........................................3-9 Windshield Washer .........................................3-9 Cruise Control ..............................................3-10 Exterior Lamps .............................................3-14 Wiper Activated Headlamps ............................3-15 Headlamps on Reminder ................................3-15 Daytime Running Lamps (DRL)/ Automatic Headlamp System .......................3-15 Instrument Panel Brightness ...........................3-16 Interior Lamps Control ...................................3-17 Dome Lamp .................................................3-17 Entry Lighting ...............................................3-17 Delayed Lighting ...........................................3-18 Exit Lighting .................................................3-18 Front Reading Lamps ....................................3-19 Rear Reading Lamps ....................................3-19 Cargo Lamp .................................................3-19 Battery Run-Down Protection ..........................3-19 Overhead Console Switchbank .......................3-20 Ultrasonic Rear Parking Assist (URPA) ............3-20 Accessory Power Outlets ...............................3-23 Power Outlet 115 Volt Alternating Current ........3-24 Climate Controls ............................................3-25 Dual Climate Control System ..........................3-25 Outlet Adjustment .........................................3-28 Rear Climate Control System .........................3-29 Warning Lights, Gages, and Indicators ............3-31 Instrument Panel Cluster ................................3-32 Speedometer and Odometer ...........................3-33 Trip Odometer ..............................................3-33 Tachometer .................................................3-33 Safety Belt Reminder Light .............................3-33 Passenger Safety Belt Reminder Light .............3-34 Airbag Readiness Light ..................................3-34 Passenger Airbag Status Indicator ...................3-35 Charging System Light ..................................3-37 Brake System Warning Light ..........................3-37 Anti-Lock Brake System Warning Light .............3-38 3-1 Section 3 Instrument Panel Traction Control System (TCS) Warning Light ......3-39 Engine Coolant Temperature Gage ..................3-39 Malfunction Indicator Lamp .............................3-40 Oil Pressure Light .........................................3-42 Security Light ...............................................3-43 Cruise Control Light ......................................3-43 Highbeam On Light .......................................3-44 Fuel Gage ...................................................3-44 Low Fuel Warning Light .................................3-44 Driver Information Center (DIC) .......................3-45 DIC Operation and Displays ...........................3-46 DIC Warnings and Messages .........................3-51 DIC Vehicle Personalization (Uplevel Only) .......3-68 Audio System(s) .............................................3-77 Setting the Time ...........................................3-77 Radio with CD ..............................................3-77 Navigation/Radio System ...............................3-96 Rear Seat Entertainment System ....................3-96 Rear Seat Audio (RSA) ................................3-110 Theft-Deterrent Feature ................................3-112 Audio Steering Wheel Controls ......................3-112 Radio Reception .........................................3-113 Care of Your CDs and DVDs ........................3-113 Care of Your CD and DVD Player .................3-114 Fixed Mast Antenna ....................................3-114 XM™ Satellite Radio Antenna System ............3-114 3-2 ✍ NOTES 3-3 Instrument Panel Overview 3-4 The main components of the instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 3-28. B. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-7. C. Audio Steering Wheel Controls (If Equipped). See Audio Steering Wheel Controls on page 3-112. D. Instrument Panel Cluster. See Instrument Panel Cluster on page 3-32. E. DIC Controls (If Equipped). See Driver Information Center (DIC) on page 3-45. F. Traction Control System Button. See Traction Control System (TCS) on page 4-9. G. Hazard Warning Flasher Switch. See Hazard Warning Flashers on page 3-6. H. Passenger Airbag Status Indicator. See Passenger Airbag Status Indicator on page 3-35. I. Audio System. See Audio System(s) on page 3-77. J. Exterior Lamps Control. See Exterior Lamps on page 3-14. K. Interior Lamps Control. See Interior Lamps Control on page 3-17. Instrument Panel Brightness Control. See Instrument Panel Brightness on page 3-16. L. Hood Release. See Hood Release on page 5-11. M. Parking Brake. See Parking Brake on page 2-37. N. Horn. See Horn on page 3-6. O. Cruise Controls (If Equipped). See Cruise Control on page 3-10. P. Climate Controls. See Dual Climate Control System on page 3-25. Q. Heated Seat Controls (If Equipped). See Heated Seats on page 1-4. R. Glove Box. See Glove Box on page 2-48. 3-5 Horn Press near or on the horn symbols on your steering wheel pad to sound the horn. Tilt Wheel A tilt wheel allows you to adjust the steering wheel before you drive. You can raise the steering wheel to the highest level to give your legs more room when you enter and exit the vehicle. The lever that allows you to tilt the steering wheel is located on the left side of the steering column. To tilt the wheel, hold the wheel and pull the lever. Then move the wheel to a comfortable position and release the lever to lock the wheel in place. Hazard Warning Flashers Your hazard warning ﬂashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will ﬂash on and off. The hazard warning ﬂasher button is located near the center of the instrument panel. Your hazard warning ﬂashers work no matter what position your key is in, and even if the key is not in. Press the button to make the front and rear turn signal lamps ﬂash on and off. Press the button again to turn the ﬂashers off. When the hazard warning ﬂashers are on, your turn signals will not work. Other Warning Devices If you carry reﬂective triangles, you can set them up at the side of the road about 300 feet (100 m) behind your vehicle. 3-6 Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: (cid:127) G Turn and Lane Change Signals. See Turn and Lane-Change Signals on page 3-7. (cid:127) 3 Headlamp High/Low-Beam Changer. See Headlamp High/Low-Beam Changer on page 3-8. Flash-to-Pass. See Flash-to-Pass on page 3-8. (cid:127) N Windshield Wipers. See Windshield Wipers on page 3-9. (cid:127) L Windshield Washer. See Windshield Washer on page 3-9. (cid:127) Z Rear Window Wiper. See Windshield Washer on page 3-9. (cid:127) = Rear Window Washer. See Windshield Washer on page 3-9. For information on the headlamps, see Exterior Lamps on page 3-14. Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2005 Buick Terraza Owners Manual