Login- Download PDF Manual
-
level of performance and safety if tires not recommended for those wheels are selected. You may increase the chance that you will crash and suffer serious injury. Only use GM specific wheel and tire systems developed for your vehicle, and have them properly installed by a GM certified technician.
See Buying New Tires on page 427 and Accessories and Modifications on page 356 for additional information.
Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration (NHTSA), which grades tires by treadwear, traction, and temperature performance. This applies only to vehicles sold in the United States. The grades are molded on the sidewalls of most passenger car tires. The Uniform Tire Quality Grading (UTQG) system does not apply to deep tread, winter-type snow tires, space-saver, or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-production tires. While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades, they must also conform to federal safety requirements and additional General Motors Tire Performance Criteria (TPC) standards.
429
Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.
Traction – AA, A, B, C The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warning: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.
430
Wheel Alignment and Tire Balance The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis. However, if you notice unusual tire wear or your vehicle pulling to one side or the other, the alignment may need to be checked. If you notice your vehicle vibrating when driving on a smooth road, your tires and wheels may need to be rebalanced. See your dealer for proper diagnosis.
Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
431
Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts, and wheel nuts should be replaced. If the wheel leaks air, replace it (except some aluminum wheels, which can sometimes be repaired). See your dealer if any of these conditions exist. Your dealer will know the kind of wheel you need. Each new wheel should have the same load-carrying capacity, diameter, width, offset and be mounted the same way as the one it replaces. If you need to replace any of your wheels, wheel bolts, or wheel nuts, replace them only with new GM original equipment parts. This way, you will be sure to have the right wheel, wheel bolts, and wheel nuts for your vehicle.
{CAUTION:
Using the wrong replacement wheels, wheel bolts, or wheel nuts on your vehicle can be dangerous. It could affect the braking and handling of your vehicle, make your tires lose air and make you lose control. You could have a collision in which you or others could be injured. Always use the correct wheel, wheel bolts, and wheel nuts for replacement.
Notice: The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, bumper height, vehicle ground clearance, and tire or tire chain clearance to the body and chassis. See Changing a Flat Tire on page 436 for more information.
432
Used Replacement Wheels
Tire Chains
{CAUTION:
{CAUTION:
Putting a used wheel on your vehicle is dangerous. You cannot know how it has been used or how far it has been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel.
Do not use tire chains. There is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle parts. The area damaged by the tire chains could cause you to lose control of your vehicle and you or others may be injured in a crash. Use another type of traction device only if its manufacturer recommends it for use on your vehicle and tire size combination and road conditions. Follow that manufacturer’s instructions. To help avoid damage to your vehicle, drive slowly, re-adjust or remove the device if it is contacting your vehicle, and do not spin your wheels. If you do find traction devices that will fit, install them on the rear tires.
433
Accessory Inflator Your vehicle has an accessory inflator system. It can also inflate things like basketballs and bicycle tires. It can also used to inflate the tires to the proper tire pressure. It is not designed to inflate large objects which will require more than five minutes to inflate, such as an air mattress.
You may also have an air inflator kit that is located in the rear floor storage compartment. It includes a 22 ft (6.7 m) hose with three nozzle adapters. To use the accessory inflator, do the following:
1. Attach the appropriate nozzle adapter
to the end of the hose if required.
The accessory inflator is located in the rear compartment on the driver’s side of the vehicle, behind an access cover, and near the liftgate opening.
To access the inflator, push in on the tab to remove the cover.
434
{CAUTION:
Inflating something too much can make it explode, and you or others could be injured. Be sure to read the inflator instructions, and inflate any object only to its recommended pressure.
2. Attach that end of the hose to the object you
wish to inflate.
3. Attach the other end of the hose to the outlet.
4. Press and release the switch to turn the air inflator on. The indicator light will remain on when the inflator is running. The system has an internal clock to prevent the system from overheating. The system will allow about five minutes of running time, then the compressor will stop. The indicator light will then begin to flash. When the indicator is off, the inflator can be started again by pressing the switch. If the compressor is still hot, it may only run for a short time before shutting off again.
5. Press and release the switch to turn the
inflator off.
Place the inflator kit tools in the pouch and store it in its proper location. Remove the inflator hose from the outlet during loading and unloading. Load leveling will not function with the inflator hose attached to the inflator outlet. See Electronically Controlled Air Suspension System on page 337 for more information. To reinstall the cover, line up the tabs at the back of the cover, put it in place and latch the tabs.
If the indicator light on the accessory inflator flashes continuously, it could indicate that there is a malfunction in the air suspension system. See Electronically Controlled Air Suspension System on page 337 for more information.
If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle’s tires properly. If air goes out of a tire, it is much more likely to leak out slowly. But if you should ever have a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire will create a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly. Steer to maintain lane position, and then gently brake to a stop well out of the traffic lane.
435
A rear blowout, particularly on a curve, acts much like a skid and may require the same correction you would use in a skid. In any rear blowout remove your foot from the accelerator pedal. Get the vehicle under control by steering the way you want the vehicle to go. It may be very bumpy and noisy, but you can still steer. Gently brake to a stop, well off the road if possible.
Changing a Flat Tire If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your vehicle’s hazard warning flashers. See Hazard Warning Flashers on page 154 for more information.
{CAUTION:
Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people. You and they could be badly injured or even killed. Find a level place to change your tire. To help prevent the vehicle from moving:
1. Set the parking brake firmly. 2. Put the shift lever in PARK (P).
CAUTION:
(Continued)
{CAUTION:
Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. The jack provided with your vehicle is designed only for changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. Use the jack provided with your vehicle only for changing a flat tire.
If a tire goes flat, the next part shows how to use the jacking equipment to change a flat tire safely.
436
CAUTION:
(Continued)
3. Turn off the engine and do not restart
while the vehicle is raised.
4. Do not allow passengers to remain in
the vehicle.
To be even more certain the vehicle will not move, you should put blocks at the front and rear of the tire farthest away from the one being changed. That would be the tire, on the other side, at the opposite end of the vehicle.
When your vehicle has a flat tire, use the following example as a guide to assist you in the placement of wheel blocks.
The following information will tell you next how to use the jack and change a tire.
437
Removing the Spare Tire and Tools The jacking equipment you will need is stored under the rear seat on the passenger’s side of the vehicle. See Rear Seat Operation on page 16
for more information.To release the jack from its holder, turn the knob on the jack counterclockwise to lower the jack head.
438
The tools you will be using include the wheel wrench (A), wheel blocks (B), extension(s), (socket end) (C), handle (jack end) (D), and jack (E).
A. Wheel Wrench B. Hoist Shaft C. Extension D. Retainer E. Spare or Flat Tire
(Valve Stem Pointed Up)
The following instructions explain how to remove the underbody-mounted spare located underneath your vehicle. Notice: the storage position under the vehicle when it is supported by a jack, you could damage the tire and/or your vehicle. Always remove or restow a tire when the vehicle is on the ground.
If you remove or restow a tire from/to
1. Open the liftgate. See Liftgate/Liftglass on
page 102 for more information.
2. Attach the wheel wrench (A) to the
extension (C).
3. It is exposed when the rear gate is open and
is just above the rear bumper. Be sure the socket end of the extension (C) connects to the hoist shaft (B).
4. Turn the wheel wrench counterclockwise to lower the spare tire. Keep turning the wheel wrench until the spare tire can be pulled out from under the vehicle. If the spare tire does not lower to the ground, the secondary latch is engaged causing the tire not to lower. See Secondary Latch System on page 446 for more information.
439
Removing the Flat Tire and Installing the Spare Tire
5. Tilt the retainer at the end of the cable when
the tire has been completely lowered, and pull it through the wheel opening.
If you drive away before the spare tire
6. Pull the tire out from under the vehicle. Notice: or secondary latch system cable has been reinstalled, you could damage your vehicle. Always reinstall this cable before driving your vehicle. 7. Put the spare tire near the flat tire.
440
1. If your vehicle has a wheel cap that covers
the wheel nuts, position the chisel end of the wheel wrench in the notch and pry it off.
2. Using the wheel
wrench, loosen all the wheel nuts. Do not remove them yet.
3. Turn the jack adjusting knob clockwise by
hand to raise the jack lift head.
4. Place the handle, extension, and wheel
wrench onto the jack.
Front Position
Rear Position
A. Front Frame/Rear Axle B. Jack C. Handle D. Extension E. Wheel Wrench
441
5. Place the jack in the appropriate position
nearest the flat tire.
{CAUTION:
Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack.
{CAUTION:
Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle.
442
6. Raise the vehicle by turning the jack handle clockwise. Raise the vehicle far enough off the ground so there is enough room for the spare tire to fit.
7. Remove all the
wheel nuts and take off the flat tire.
CAUTION:
(Continued)
In an emergency, you can use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later, if needed, to get all the rust or dirt off.
{CAUTION:
Rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts become loose after time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from the places where the wheel attaches to the vehicle.
CAUTION:
(Continued)
8. Remove any rust or dirt from the wheel bolts, mounting surfaces, and spare wheel.
443
9. Place the spare tire on the wheel-mounting
surface.
{CAUTION:
Never use oil or grease on studs or nuts. If you do, the nuts might come loose. Your wheel could fall off, causing a serious accident.
10. Put the nuts on by hand. Make sure the
rounded end is toward the wheel.
11. Tighten each nut by hand until the wheel is
held against the hub. If a nut cannot be turned by hand, use the wheel wrench and see your dealer as soon as possible.
444
12. Lower the vehicle by turning the jack handle counterclockwise. Lower the jack completely.
{CAUTION:
Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to an accident. Be sure to use the correct wheel nuts. If you have to replace them, be sure to get new original equipment wheel nuts. Stop somewhere as soon as you can and have the nuts tightened with a torque wrench to the proper torque specification. See Capacities and Specifications on page 474
for wheel nut torque specification.Improperly tightened wheel nuts can
Notice: lead to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque specification. See Capacities and Specifications on page 474 for the wheel nut torque specification.
13. Use the wrench to tighten the wheel nuts firmly in a crisscross sequence as shown.
445
{CAUTION:
Someone standing too close during the procedure could be injured by the jack. If the spare tire does not slide off the jack completely, make sure no one is behind you or on either side of you as you pull the jack out from the spare.
Secondary Latch System Your vehicle has an underbody-mounted tire hoist assembly equipped with a secondary latch system. It is designed to stop the spare tire from suddenly falling off your vehicle if the cable holding the spare tire is damaged. For the secondary latch to work, the tire must be stored with the valve stem pointing up. See Storing a Flat or Spare Tire and Tools on page 450 for instructions on storing the spare or flat tire correctly.
{CAUTION:
Before beginning this procedure read all the instructions. Failure to read and follow the instructions could damage the hoist assembly and you and others could get hurt. Read and follow the instructions listed next.
446
To release the spare tire from the secondary latch, do the following:
1. Check under the
vehicle to see if the cable is visible. If it is not visible, proceed to Step 6.
2. If visible, first try to tighten the cable by turning the wheel wrench clockwise until you hear two clicks or feel it skip twice. You cannot overtighten the cable.
3. Loosen the cable by turning the wheel wrench
counterclockwise three or four turns.
4. Repeat this procedure at least two times.
If the spare tire lowers to the ground, continue with Step 2 of Removing the Spare Tire and Tools on page 438.
5. Turn the wrench counterclockwise until approximately 6 inches (15 cm) of cable is exposed.
447
9. Lower the jack by turning the wheel wrench
counterclockwise. Keep lowering the jack until the spare tire slides off the jack or is hanging by the cable.
10. Disconnect the jack handle from the jack and
carefully remove the jack. Use one hand to push against the spare while firmly pulling the jack out from under the spare tire with the other hand.
11. If the spare tire is hanging from the cable, insert the socket end of the extension into the hoist shaft hole on a 45 degree angle downward.
6. Attach the jack handle, extension(s) and the wheel wrench to the jack and place it under the vehicle towards the front of the rear bumper. Position the center lift point of the jack under the center of the spare tire.
7. Turn the wrench clockwise to raise the jack
until it lifts the end fitting.
8. Continue raising the jack until the spare tire
stops moving upward and is held firmly in place. The secondary latch has released and the spare tire is balancing on the jack.
448
12. Be sure that the socket end of the extension
connects to the hoist shaft.
Turn the wheel wrench counterclockwise to lower the spare the rest of the way.
13. Tilt the retainer at the end of the cable and
pull it through the wheel opening. Pull the tire out from under the vehicle.
If you drive away before the spare tire
Notice: or secondary latch system cable has been reinstalled, you could damage your vehicle. Always reinstall this cable before driving your vehicle. 14. Turn the wheel wrench clockwise to raise the
cable back up if the cable is hanging under the vehicle.
Have the hoist assembly inspected as soon as you can. You will not be able to store a spare tire using the hoist assembly until it has been repaired or replaced.
449
Storing a Flat or Spare Tire and Tools
{CAUTION:
{CAUTION:
Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.
450
The underbody-mounted spare tire needs to be stored with the valve stem pointing up. If the spare tire is stored with the valve stem pointing downward, its secondary latch will not work properly and the spare tire could loosen and suddenly fall from your vehicle. If this happened when your vehicle was being driven, the tire might contact a person or another vehicle, causing injury and, of course, damage to itself as well. Be sure the underbody-mounted spare tire is stored with its valve stem pointing up.
Notice: An aluminum wheel with a flat tire should always be stored under the vehicle with the hoist. However, storing it that way for an extended period could damage the wheel. To avoid this, always stow the wheel properly with the valve stem pointing up and have the wheel repaired as soon as possible.
3. Make sure the valve stem is pointed up and
to the rear. Then pull the retainer (D) through the wheel opening.
4. Put the socket end of the extension (C)
through the hole just above the rear bumper at a 45 degree downward angle. Connect the socket end of the extension to the hoist shaft (B).
5. Raise the tire fully against the underside of
the vehicle. Continue turning the wheel wrench (A) clockwise until you hear two clicks or feel it skip twice. This indicates that the tire is secure and the cable is tight. The spare tire hoist cannot be overtightened.
Follow this diagram to store the underbody-mounted flat or spare tire.
A. Wheel Wrench B. Hoist Shaft C. Extension D. Retainer E. Spare or Flat Tire
(Valve Stem Pointed Up)
1. Put the tire (E) on the ground at the rear of
the vehicle.
2. Remove the wheel cap, if the vehicle has one,
from the flat tire by tapping the backside of the wheel cap with the wheel wrench (A). Store in a safe location until the flat tire is repaired. Once the tire is repaired, replace the wheel cap.
451
6. Make sure the tire is stored securely. Push,
pull (A), and then try to turn (B) the tire. If the tire moves, use the wheel wrench and socket end of the extension to tighten the cable.
7. Return the equipment to the proper location in
the vehicle as shown next.
452
A. Handle B. Wheel Wrench C. Instruction Label 1. Attach the handle (A), wheel wrench (B) and
D. Extension E. Knob F. Wheel Blocks and Jack
extension (D) in the slots provided.
2. Roll up the instruction label (C) and return to
the slot in the tool kit.
3. Assemble the wheel blocks (F) to the jack. 4. Turn the knob (E) on the jack clockwise
to raise the jack head.
5. Return the rear seat to its proper position.
Spare Tire Your vehicle, when new, had a fully-inflated spare tire. A spare tire may lose air over time, so check its inflation pressure regularly. See Inflation - Tire Pressure on page 419 and Loading Your Vehicle on page 330 for information regarding proper tire inflation and loading your vehicle. For instruction on how to remove, install or store a spare tire, see Removing the Flat Tire and Installing the Spare Tire on page 440
and Storing a Flat or Spare Tire and Tools on page 450. After installing the spare tire on your vehicle, you should stop as soon as possible and make sure the spare is correctly inflated. Have the damaged or flat road tire repaired or replaced as soon as you can and installed back onto your vehicle. This way, a spare tire will be available in case you need it again. Do not mix tires and wheels of different sizes, because they will not fit. Keep your spare tire and its wheel together.Appearance Care
Cleaning the Inside of Your Vehicle Your vehicle’s interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on your upholstery. Dirt can damage carpet, fabric, leather, and plastic surfaces. Regular vacuuming is recommended to remove particles from your upholstery. It is important to keep your upholstery from becoming and remaining heavily soiled. Soils should be removed as quickly as possible. Your vehicle’s interior may experience extremes of heat that could cause stains to set rapidly. Lighter colored interiors may require more frequent cleaning. Use care because newspapers and garments that transfer color to your home furnishings may also transfer color to your vehicle’s interior. When cleaning your vehicle’s interior, only use cleaners specifically designed for the surfaces being cleaned. Permanent damage may result from using cleaners on surfaces for which they were not intended. Use glass cleaner only on glass.
453
If you use abrasive cleaners when
Remove any accidental over-spray from other surfaces immediately. To prevent over-spray, apply cleaner directly to the cleaning cloth. Notice: cleaning glass surfaces on your vehicle, you could scratch the glass and/or cause damage to the rear window defogger. When cleaning the glass on your vehicle, use only a soft cloth and glass cleaner. Many cleaners contain solvents that may become concentrated in your vehicle’s breathing space. Before using cleaners, read and adhere to all safety instructions on the label. While cleaning your vehicle’s interior, maintain adequate ventilation by opening your vehicle’s doors and windows. Dust may be removed from small buttons and knobs using a small brush with soft bristles. Your GM dealer has a product for cleaning your vehicle’s glass. Should it become necessary, you can also obtain a product from your GM dealer to remove odors from your vehicle’s upholstery.
454
Do not clean your vehicle using the following cleaners or techniques: (cid:127) Never use a knife or any other sharp object to
remove a soil from any interior surface.
(cid:127) Never use a stiff brush. It can cause damage
to your vehicle’s interior surfaces. (cid:127) Never apply heavy pressure or rub
aggressively with a cleaning cloth. Use of heavy pressure can damage your interior and does not improve the effectiveness of soil removal.
(cid:127) Use only mild, neutral-pH soaps. Avoid laundry
detergents or dishwashing soaps with degreasers. Using too much soap will leave a residue that leaves streaks and attracts dirt. For liquid cleaners, about 20 drops per gallon (3.78 L) of water is a good guide.
(cid:127) Do not heavily saturate your upholstery while
cleaning.
(cid:127) Damage to your vehicle’s interior may result
from the use of many organic solvents such as naptha, alcohol, etc.
Fabric/Carpet Use a vacuum cleaner with a soft brush attachment frequently to remove dust and loose dirt. A canister vacuum with a beater bar in the nozzle may only be used on floor carpet and carpeted floor mats. For soils, always try to remove them first with plain water or club soda. Before cleaning, gently remove as much of the soil as possible using one of the following techniques: (cid:127) For liquids: gently blot the remaining soil
with a paper towel. Allow the soil to absorb into the paper towel until no more can be removed.
(cid:127) For solid dry soils: remove as much as
possible and then vacuum.
To clean, use the following instructions: 1. Saturate a lint-free, clean white cloth with
water or club soda.
2. Wring the cloth to remove excess moisture.
3. Start on the outside edge of the soil and
gently rub toward the center. Continue cleaning, using a clean area of the cloth each time it becomes soiled.
4. Continue to gently rub the soiled area until the
cleaning cloth remains clean.
5. If the soil is not completely removed, use a mild soap solution and repeat the cleaning process that was used with plain water.
If any of the soil remains, a commercial fabric cleaner or spot lifter may be necessary. When a commercial upholstery cleaner or spot lifter is to be used, test a small hidden area for colorfastness first. If the locally cleaned area gives any impression that a ring formation may result, clean the entire surface. After the cleaning process has been completed, a paper towel can be used to blot excess moisture from the fabric or carpet.
455
Leather A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary, a soft cloth dampened with a mild soap solution can be used. Allow the leather to dry naturally. Do not use heat to dry. Never use steam to clean leather. Never use spot lifters or spot removers on leather. Many commercial leather cleaners and coatings that are sold to preserve and protect leather may permanently change the appearance and feel of your leather and are not recommended. Do not use silicone or wax-based products, or those containing organic solvents to clean your vehicle’s interior because they can alter the appearance by increasing the gloss in a non-uniform manner. Never use shoe polish on your leather.
Instrument Panel, Vinyl, and Other Plastic Surfaces A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary, a clean soft cloth dampened with a mild soap solution can be used to gently remove dust and dirt. Never use spot lifters or removers on plastic surfaces. Many commercial cleaners and coatings that are sold to preserve and protect soft plastic surfaces may permanently change the appearance and feel of your interior and are not recommended. Do not use silicone or wax-based products, or those containing organic solvents to clean your vehicle’s interior because they can alter the appearance by increasing the gloss in a non-uniform manner. Some commercial products may increase gloss on your instrument panel. The increase in gloss may cause annoying reflections in the windshield and even make it difficult to see through the windshield under certain conditions.
456
Care of Safety Belts Keep belts clean and dry.
{CAUTION:
Do not bleach or dye safety belts. If you do, it may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.
Washing Your Vehicle The paint finish on the vehicle provides beauty, depth of color, gloss retention, and durability. The best way to preserve the vehicle’s finish is to keep it clean by washing it often with lukewarm or cold water. Do not wash the vehicle in the direct rays of the sun. Use a car washing soap. Do not use strong soaps or chemical detergents. Be sure to rinse the vehicle well, removing all soap residue completely. Approved cleaning products can be obtained from your dealer. See Vehicle Care/Appearance Materials on page 462. Do not use cleaning agents that are petroleum based, or that contain acid or abrasives. All cleaning agents should be flushed promptly and not allowed to dry on the surface, or they could stain. Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting. High pressure car washes may cause water to enter the vehicle.
457
Cleaning Exterior Lamps/Lenses Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under Washing Your Vehicle on page 457.
Finish Care Occasional waxing or mild polishing of your vehicle by hand may be necessary to remove residue from the paint finish. You can get GM-approved cleaning products from your dealer. See Vehicle Care/Appearance Materials on page 462. If your vehicle has a “basecoat/clearcoat” paint finish, the clearcoat gives more depth and gloss to the colored basecoat. Always use waxes and polishes that are non-abrasive and made for a basecoat/clearcoat paint finish. Notice: Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/clearcoat paint finish on your vehicle.
458
Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage your vehicle’s finish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter. Exterior painted surfaces are subject to aging, weather and chemical fallout that can take their toll over a period of years. You can help to keep the paint finish looking new by keeping your vehicle garaged or covered whenever possible. Protecting Exterior Bright Metal Parts Bright metal parts should be cleaned regularly to keep their luster. Washing with water is all that is usually needed. However, you may use chrome polish on chrome or stainless steel trim, if necessary. Use special care with aluminum trim. To avoid damaging protective trim, never use auto or chrome polish, steam or caustic soap to clean aluminum. A coating of wax, rubbed to high polish, is recommended for all bright metal parts.
Windshield, Backglass, and Wiper Blades If the windshield is not clear after using the windshield washer, or if the wiper blade chatters when running, wax, sap or other material may be on the blade or windshield. Clean the outside of the windshield with a full-strength glass cleaning liquid. The windshield is clean if beads do not form when you rinse it with water. Grime from the windshield will stick to the wiper blades and affect their performance. Clean the blade by wiping vigorously with a cloth soaked in full-strength windshield washer solvent. Then rinse the blade with water. Check the wiper blades and clean them as necessary; replace blades that look worn.
If you use strong soaps, chemicals,
Aluminum Wheels Notice: abrasive polishes, cleaners, brushes, or cleaners that contain acid on aluminum or chrome-plated wheels, you could damage the surface of the wheel(s). The repairs would not be covered by your warranty. Use only GM-approved cleaners on aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied. Notice: Using chrome polish on aluminum wheels could damage the wheels. The repairs would not be covered by your warranty. Use chrome polish on chrome wheels only. The surface of these wheels is similar to the painted surface of the vehicle. Do not use strong soaps, chemicals, abrasive polishes, abrasive cleaners, cleaners with acid, or abrasive cleaning brushes on them because the surface could be damaged. Do not use chrome polish on aluminum wheels.
459
Notice: If you drive your vehicle through an automatic car wash that has silicone carbide tire cleaning brushes, you could damage the aluminum or chrome-plated wheels. The repairs would not be covered by your warranty. Never drive a vehicle equipped with aluminum or chrome-plated wheels through an automatic car wash that uses silicone carbide tire cleaning brushes. Do not take the vehicle through an automatic car wash that has silicone carbide tire cleaning brushes. These brushes can also damage the surface of these wheels.
Tires To clean the tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on your vehicle may damage the paint finish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on your vehicle.
Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the warranty.
Finish Damage Any stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into major repair expense. Minor chips and scratches can be repaired with touch-up materials available from your dealer. Larger areas of finish damage can be corrected in your dealer’s body and paint shop.
460
Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not removed, corrosion and rust can develop on the underbody parts such as fuel lines, frame, floor pan, and exhaust system even though they have corrosion protection. At least every spring, flush these materials from the underbody with plain water. Clean any areas where mud and debris can collect. Dirt packed in close areas of the frame should be loosened before being flushed. Your dealer or an underbody car washing system can do this for you.
Chemical Paint Spotting Some weather and atmospheric conditions can create a chemical fallout. Airborne pollutants can fall upon and attack painted surfaces on the vehicle. This damage can take two forms: blotchy, ring-shaped discolorations, and small, irregular dark spots etched into the paint surface. Although no defect in the paint job causes this, GM will repair, at no charge to the owner, the surfaces of new vehicles damaged by this fallout condition within 12 months or 12,000 miles (20 000 km) of purchase, whichever occurs first.
461
Vehicle Care/Appearance Materials
Description
Usage
Description
Usage
Swirl Remover Polish
Polishing Cloth Wax-Treated
Tar and Road Oil Remover
Interior and exterior polishing cloth.
Removes tar, road oil, and asphalt.
Chrome Cleaner and Polish
Use on chrome or stainless steel.
White Sidewall Tire Cleaner
Removes soil and black marks from whitewalls.
Vinyl Cleaner
Cleans vinyl.
Glass Cleaner
Chrome and Wire Wheel Cleaner
Finish Enhancer
Removes dirt, grime, smoke and fingerprints.
Removes dirt and grime from chrome wheels and wire wheel covers.
Removes dust, fingerprints, and surface contaminants. Spray on and wipe off.
Cleaner Wax
Foaming Tire Shine Low Gloss
Wash Wax Concentrate
Spot Lifter
Odor Eliminator
Removes swirl marks, fine scratches, and other light surface contamination.
Removes light scratches and protects finish.
Cleans, shines, and protects in one step. No wiping necessary.
Medium foaming shampoo. Cleans and lightly waxes. Biodegradable and phosphate free.
Quickly removes spots and stains from carpets, vinyl, and cloth upholstery.
Odorless spray odor eliminator used on fabrics, vinyl, leather and carpet.
462
Vehicle Identification
Vehicle Identification Number (VIN)
Engine Identification The eighth character in the VIN is the engine code. This code will help you identify your vehicle’s engine, specifications, and replacement parts.
Service Parts Identification Label You will find this label on the inside of the glove box. It is very helpful if you ever need to order parts. On this label, you will find the following: (cid:127) VIN (cid:127) Model designation (cid:127) Paint information (cid:127) Production options and special equipment Do not remove this label from the vehicle.
This is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle. The VIN also appears on the Certification/Tire and Service Parts labels and the certificates of title and registration.
463
Electrical System
Add-On Electrical Equipment Notice: Do not add anything electrical to your vehicle unless you check with your dealer first. Some electrical equipment can damage your vehicle and the damage would not be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should. Add-on equipment can drain your vehicle’s battery, even if your vehicle is not operating. Your vehicle has an airbag system. Before attempting to add anything electrical to your vehicle, see Servicing Your Airbag-Equipped Vehicle on page 84.
Headlamps The headlamp wiring is protected by four fuses. An electrical overload will cause a lamp to go on and off. If this happens, have your headlamp wiring checked right away.
Windshield Wiper Fuses The windshield wiper motor is protected by a circuit breaker and a fuse. If the motor overheats due to heavy snow or ice, the wiper will stop until the motor cools. If the overload is caused by some electrical problem, be sure to get it fixed.
Power Windows and Other Power Options Circuit breakers protect the power windows and other power accessories. When the current load is too heavy, the circuit breaker opens and closes, protecting the circuit until the problem is fixed or goes away.
464
Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses and circuit breakers. This greatly reduces the chance of fires caused by electrical problems. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure you replace a bad fuse with a new one of the identical size and rating. If you ever have a problem on the road and don’t have a spare fuse, you can borrow one that has the same amperage. Just pick some feature of your vehicle that you can get along without — like the radio or cigarette lighter — and use its fuse, if it is the correct amperage. Replace it as soon as you can.
Engine Compartment Fuse Block
The fuse block is located under the hood in the engine compartment on the driver’s side of the vehicle. See Engine Compartment Overview on page 366 for more information on location. Remove the primary cover by pressing the two locking tabs. Remove the secondary cover by snapping off while lifting. To reinstall the fuse panel cover, reverse the sequence.
465
L6 Engine
Fuses
Usage
Electrically-Controlled Air Suspension Passenger’s Side High-Beam Headlamp
Fuses
Usage
Passenger’s Side Low-Beam Headlamp Back-Up Trailer Lamps
466
Fuses
Usage
Fuses
Usage
10
11
12
13
14
15
16
17
18
19
20
21
22
2324
Driver’s Side High-Beam Headlamp Driver’s Side Low-Beam Headlamp Windshield Wiper Automatic Transfer Case Windshield Washer Powertrain Control Module B Fog Lamps Stoplamp Cigarette Lighter Not Used Electric Adjustable Pedal Truck Body Controller, Ignition 1
Crank Airbag Trailer Electric Brake Cooling Fan Horn Ignition E Electronic Throttle Control Instrument Panel Cluster, Driver Information Center25
26
27
28
29
30
31
32
33
34
35
36
50
51
52
5354
56
58
59
Automatic Shift Lock Control System Transmission Control Module (TCM) Canister Backup Powertrain Control Module 1
Oxygen Sensor Air Conditioning Truck Body Controller 1
Trailer Anti-lock Brakes (ABS) Ignition A Blower Motor Ignition B Passenger’s Side Trailer Turn Driver’s Side Trailer Turn Hazard Flashers Headlamp Driver Module Air Injection Reactor (AIR) Solenoid Air Injection Reactor (AIR) Pump Vehicle Stability Enhancement System (StabiliTrak®) Regulated Voltage Control467
Relays
Usage
Relays
Usage
37
38
39
40
41
42
43
44
45Headlamp Washer Rear Window Wiper/Washer Fog Lamps Horn Fuel Pump Windshield Washer High-Beam Headlamp Air Conditioning Cooling Fan
46
47
49
55
57Headlamp Driver Module Starter Electric Adjustable Pedal Air Injection Reactor (AIR) Solenoid Powertrain
Miscellaneous
Usage
48
Instrument Panel Battery
468
V8 Engine
Fuses
Usage
Electrically-Controlled Air Suspension Passenger’s Side High-Beam Headlamp
Fuses
Usage
Passenger’s Side Low-Beam Headlamp Back-Up-Trailer Lamps
469
Fuses
Usage
Fuses
Usage
10
11
12
13
1415
16
17
18
19
20
21
22
2324
Driver’s Side High-Beam Headlamp Driver’s Side Low-Beam Headlamp Windshield Wiper Automatic Transfer Case Windshield Washer Powertrain Control Module B Fog Lamps Stoplamp Cigarette Lighter Ignition Coils Transmission Control Module Canister Vent Truck Body Controller, Ignition 1
Crank Airbag Trailer Electric Brake Cooling Fan Horn Ignition E Electronic Throttle Control Instrument Panel Cluster, Driver Information Center470
25
26
27
28
29
30
31
32
33
34
35
36
50
51
52
53
54
55
56
57
58
59Automatic Shift Lock Control System Engine 1
Backup Powertrain Control Module 1
Powertrain Control Module Air Conditioning Injector Bank A Trailer Anti-lock Brakes (ABS) Ignition A Blower Motor Ignition B Passenger’s Side Trailer Turn Driver’s Side Trailer Turn Hazard Flashers Transmission Oxygen Sensor Bank B Oxygen Sensor Bank A Injector Bank B Headlamp Driver Module Body Controller 1
Electric Adjustable PedalRear Underseat Fuse Block
Fuses
61
62
Usage
Vehicle Stability Enhancement System (StabiliTrak®) Regulated Voltage Control
Relays
Usage
37
38
39
40
41
42
43
44
45
46
47
49
60Headlamp Washer Rear Window Wiper Fog Lamps Horn Fuel Pump Windshield Washer High-Beam Headlamp Air Conditioning Cooling Fan Headlamp Driver Module Starter Electric Adjustable Pedal Powertrain
Miscellaneous
Usage
48
Instrument Panel Battery
471
Fuses
01
02
03
04Usage
Passenger Door Control Module Driver Door Control Module Liftgate Module 2
Truck Body Controller 3Fuses
05
06
07
08Usage
Rear Fog Lamps Blank Truck Body Controller 2
Power Seats472
Fuses
Usage
Fuses
Usage
09
10
11
12
13
14
1516
17
18
19
20
21
23
24
25
2627
28
29
30Rear Wiper Driver Door Module Amplifier Passenger Door Module Rear Climate Controls Driver Side Rear Parking Lamps Blank Vehicle Center High-Mounted Stoplamp (CHMSL) Passenger Side Rear Parking Lamps Locks Liftgate Module/Driver Seat Module Blank Lock Blank Unlock Blank Blank OnStar® Overhead Battery, OnStar® System Sunroof Rainsense™ Wipers Parking Lamps
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52Truck Body Controller Accessory Truck Body Controller 5
Front Wipers Vehicle Stop Transmission Control Module Heat Ventilation Air Conditioning B Front Parking Lamps Driver Side Turn Signal Heat Ventilation Air Conditioning I Truck Body Controller 4
Radio Trailer Park Passenger Side Turn Signal Heat Ventilation Air Conditioning Rear Fog Lamps Auxiliary Power 1
Ignition 0
Four-Wheel Drive Blank Truck Body Controller Ignition Brakes Truck Body Controller Run473
Capacities and Specifications The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 489 for more information.
Application
Air Conditioning Refrigerant R134a
Cooling System
4.2L L6 Engine 5.3L V8 Engine
Engine Oil with Filter
4.2L L6 Engine 5.3L V8 Engine
Capacities
English
Metric
For the air conditioning system refrigerant charge amount, see the refrigerant caution label located
under the hood. See your dealer for more information.
10.8 qt 12.2 qt
10.2 L 11.6 L
7.0 qt 6.0 qt 22.0 gal 2.0 qt 5.0 qt 100 lb ft
6.6 L 5.7 L 83.3 L 1.8 L 4.7 L
Fuel Tank Transfer Case Lubricant Transmission (Drain and Refill) Wheel Nut Torque All capacities are approximate. When adding, be sure to fill to the appropriate level, as recommended in this manual. Recheck the fluid level after filling.
140 Y
Engine Specifications
Engine
VORTEC™ 4.2L L6
VORTEC™ 5.3L V8VIN Code
Transmission
Automatic Automatic
Spark Plug Gap
0.040 inches (1.01 mm) 0.040 inches (1.01 mm)
474
Section 6
Maintenance Schedule
Maintenance Schedule ................................ 476
Introduction ............................................... 476
Maintenance Requirements ........................ 476
Your Vehicle and the Environment ............ 477
Using the Maintenance Schedule ............... 477
Scheduled Maintenance ............................. 479
Additional Required Services ..................... 482
Maintenance Footnotes .............................. 483
Owner Checks and Services ..................... 485At Each Fuel Fill ....................................... 485
At Least Once a Month ............................. 486
At Least Once a Year ............................... 486
Recommended Fluids and Lubricants ........ 489
Normal MaintenanceReplacement Parts ................................. 491
Engine Drive Belt Routing ......................... 492
Maintenance Record .................................. 493475
Maintenance Schedule
Introduction Important: Keep engine oil at the proper level and change as recommended.
Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts, and recommended fluids and lubricants as prescribed in this manual are necessary to keep your vehicle in good working condition. Any damage caused by failure to follow scheduled maintenance may not be covered by warranty.
Have you purchased the GM Protection Plan? The Plan supplements your new vehicle warranties. See your Warranty and Owner Assistance booklet or your dealer for details.
476
Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep your vehicle in good working condition, but also helps the environment. All recommended maintenance is important. Improper vehicle maintenance can even affect the quality of the air we breathe. Improper fluid levels or the wrong tire inflation can increase the level of emissions from your vehicle. To help protect our environment, and to keep your vehicle in good condition, be sure to maintain your vehicle properly.
Using the Maintenance Schedule We at General Motors want to help you keep your vehicle in good working condition. But we do not know exactly how you will drive it. You may drive very short distances only a few times a week. Or you may drive long distances all the time in very hot, dusty weather. You may use your vehicle in making deliveries. Or you may drive it to work, to do errands, or in many other ways. Because of all the different ways people use their vehicles, maintenance needs vary. You may need more frequent checks and replacements. So please read the following and note how you drive. If you have any questions on how to keep your vehicle in good condition, see your GM Goodwrench® dealer.
477
This schedule is for vehicles that: (cid:127) carry passengers and cargo within
recommended limits. You will find these limits on the Tire and Loading Information label. See Loading Your Vehicle on page 330.
(cid:127) are driven on reasonable road surfaces within
legal driving limits.
(cid:127) are driven off-road in the recommended
manner. See Off-Road Driving on page 299.
(cid:127) use the recommended fuel. See Gasoline
Octane on page 358.
The services in Scheduled Maintenance on page 479 should be performed when indicated. See Additional Required Services on page 482 and Maintenance Footnotes on page 483 for further information.
{CAUTION:
Performing maintenance work on a vehicle can be dangerous. In trying to do some jobs, you can be seriously injured. Do your own maintenance work only if you have the required know-how and the proper tools and equipment for the job. If you have any doubt, see your GM Goodwrench® dealer to have a qualified technician do the work. See Doing Your Own Service Work on page 357.
Some maintenance services can be complex. So, unless you are technically qualified and have the necessary equipment, you should have your GM Goodwrench® dealer do these jobs. When you go to your GM Goodwrench® dealer for your service needs, you will know that GM-trained and supported service technicians will perform the work using genuine GM parts.
478
If you want to purchase service information, see Service Publications Ordering Information on page 517. Owner Checks and Services on page 485 tells you what should be checked, when to check it, and what you can easily do to help keep your vehicle in good condition. The proper replacement parts, fluids, and lubricants to use are listed in Recommended Fluids and Lubricants on page 489 and Normal Maintenance Replacement Parts on page 491. When your vehicle is serviced, make sure these are used. All parts should be replaced and all necessary repairs done before you or anyone else drives the vehicle. We recommend the use of genuine GM parts.
Scheduled Maintenance When the CHANGE ENGINE OIL DIC message comes on, it means that service is required for your vehicle. See DIC Warnings and Messages on page 202. Have your vehicle serviced as soon as possible within the next 600 miles (1 000 km). It is possible that, if you are driving under the best conditions, the engine oil life system may not indicate that vehicle service is necessary for over a year. However, the engine oil and filter must be changed at least once a year and at this time the system must be reset. Your GM Goodwrench® dealer has GM-trained service technicians who will perform this work using genuine GM parts and reset the system.
479
If the engine oil life system is ever reset accidentally, you must service your vehicle within 3,000 miles (5 000 km) since your last service. Remember to reset the oil life system whenever the oil is changed. See Engine Oil Life System on page 372 for information on the Engine Oil Life System and resetting the system. When the CHANGE ENGINE OIL DIC message appears, certain services, checks, and inspections are required. Required services are described in the following for “Maintenance I” and “Maintenance II.” Generally, it is recommended that your first service be Maintenance I, your second service be Maintenance II, and that you alternate Maintenance I and Maintenance II thereafter. However, in some cases, Maintenance II may be required more often.
Maintenance I — Use Maintenance I if the message comes on within 10 months since the vehicle was purchased or Maintenance II was performed. Maintenance II — Use Maintenance II if the previous service performed was Maintenance I. Always use Maintenance II whenever the message comes on 10 months or more since the last service or if the message has not come on at all for one year.
480
Scheduled Maintenance
Service
Maintenance I Maintenance II
Change engine oil and filter. See Engine Oil on page 369. Reset oil life system. See Engine Oil Life System on page 372. An Emission Control Service. Visually check for any leaks or damage. See footnote (j). Inspect engine air cleaner filter. If necessary, replace filter. See Engine Air Cleaner/Filter on page 374. See footnote (k). Rotate tires and check inflation pressures and wear. See Tire Inspection and Rotation on page 425 and “Tire Wear Inspection” in At Least Once a Month on page 486. Inspect brake system. See footnote (a). Check engine coolant and windshield washer fluid levels and add fluid as needed. Perform any needed additional services. See “Additional Required Services” in this section. Inspect suspension and steering components. See footnote (b). Inspect engine cooling system. See footnote (c). Inspect wiper blades. See footnote (d). Inspect restraint system components. See footnote (e). Lubricate body components. See footnote (f). Check transmission fluid level and add fluid as needed. See footnote (g).
•
•
•
•
•
•
•
•
•
•
•
•
•
• • • • • •
481
Additional Required Services The following services should be performed at the first maintenance service (I or II) after the indicated miles (kilometers) shown for each item.
Service and Miles (Kilometers)
Additional Required Services 75,000
25,000
(40 000)50,000
(80 000)(120 000)
100,000
(160 000)125,000
(200 000)150,000
(240 000)•
•
Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components. Replace engine air cleaner filter. See Engine Air Cleaner/Filter on page 374. Change automatic transmission fluid and filter (severe service). See footnotes (g) and (h). Change automatic transmission fluid and filter (normal service). See footnote (g). Automatic transfer case only: Change transfer case fluid. See footnote (g). Replace spark plugs. An Emission Control Service.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
482
Additional Required Services (cont’d)
Service and Miles (Kilometers)
V8 engine only: Inspect spark plug wires. An Emission Control Service. Engine cooling system service (or every five years, whichever occurs first). An Emission Control Service. See footnote (i). Inspect engine accessory drive belt. An Emission Control Service. See footnote (l).
25,000
(40 000)50,000
(80 000)75,000
(120 000)
100,000
(160 000)125,000
(200 000)150,000
(240 000)•
•
•
Maintenance Footnotes (a) Visually inspect brake lines and hoses for proper hook-up, binding, leaks, cracks, chafing, etc. Inspect disc brake pads for wear and rotors for surface condition. Inspect other brake parts, including calipers, parking brake, etc. (b) Visually inspect front and rear suspension and steering system for damaged, loose, or missing parts or signs of wear. Inspect power steering lines and hoses for proper hook-up, binding, leaks, cracks, chafing, etc.
(c) Visually inspect hoses and have them replaced if they are cracked, swollen, or deteriorated. Inspect all pipes, fittings and clamps; replace with genuine GM parts as needed. To help ensure proper operation, a pressure test of the cooling system and pressure cap and cleaning the outside of the radiator and air conditioning condenser is recommended at least once a year. (d) Visually inspect wiper blades for wear or cracking. Replace wiper blades that appear worn or damaged or that streak or miss areas of the windshield.
483
(e) Make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors, and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired. Have any torn or frayed safety belts replaced. Also look for any opened or broken airbag coverings, and have them repaired or replaced. The airbag system does not need regular maintenance. (f) Lubricate all key lock cylinders, hood latch assembly, secondary latch, pivots, spring anchor, release pawl, rear compartment hinges, outer liftgate handle pivot points, rear door detent link, roller mechanism, liftgate handle pivot points, latch bolt, fuel door hinge, cargo door hinge, locks, and folding seat hardware. More frequent lubrication may be required when exposed to a corrosive environment. Applying silicone grease on weatherstrips with a clean cloth will make them last longer, seal better, and not stick or squeak. (g) Inspect hoses for cracks, chafing, leaks, kinks, and proper installation.
(h) Change automatic transmission fluid and filter
