Download PDF Manual

Here are some cleaning tips: (cid:127) Always read the instructions on the cleaner label. (cid:127) Clean up stains as soon as you can before they set. (cid:127) Carefully scrape off any excess stain. (cid:127) Use a clean cloth or sponge, and change to a


clean area often. A soft brush may be used if stains are stubborn. To avoid forming a ring on fabric after spot cleaning, clean the entire area immediately or it will set.


5-83


(cid:127) (cid:127) (cid:127) (cid:127) Most stains can be removed with club soda water. To clean, use the following instructions: 1. For liquids: blot with a clean, soft, white cloth. For


solids: remove as much as possible and then vacuum or brush.


2. Apply club soda water to a clean, soft, white


cloth. Do not over-saturate; the cloth should not drip water.


3. Clean the entire area. Avoid getting the fabric


too wet.


4. Start cleaning from the seams into the stain to


avoid a ring effect.


5. Continue cleaning, using a clean area of the cloth


each time it becomes soiled.


6. When the stain is removed, blot the cleaned area


with another dry, clean, soft, white cloth.


Using Cleaner on Fabric 1. First, try the cleaner in an inconspicuous area to


make sure the cleaner does not affect the color of the fabric.


2. For liquids: blot with a clean, soft, white cloth. For


solids: remove as much as possible and then vacuum or brush.


3. Spray a small amount of the cleaner onto a clean


soft, white, cloth. Do not apply spray directly to the fabric.


4. Start cleaning from the seams into the stain to


avoid a ring effect.


5. Continue cleaning, using a clean area of the cloth


each time it becomes soiled.


6. When the stain is removed, blot the cleaned area


with another dry, clean, soft, white cloth.


7. If the cleaner leaves a ring effect, follow up with the club soda water instructions given earlier in this section.


5-84


Special Fabric Cleaning Problems Stains caused by such things as catsup, black coffee, egg, fruit, fruit juice, milk, soft drinks, vomit, urine, and blood can be removed using the club soda water instructions given earlier in this section. If an odor lingers after cleaning vomit or urine, treat the area with a water and baking soda solution: 1 teaspoon (5ml) of baking soda to 1 cup (250ml) of lukewarm water. Let dry. Stains caused by oil and grease can be cleaned with an approved GM cleaner and a clean, white cloth. See Vehicle Care/Appearance Materials on page 5-90
for more information. 1. Carefully scrape off excess stain. 2. Clean with cool water and allow to dry completely. 3. If a stain remains, follow the cleaner instructions


described earlier.


Vinyl Use warm water and a clean cloth. (cid:127) Rub with a clean, damp cloth to remove dirt. This


may have to be done more than once. Things like tar, asphalt, and shoe polish will stain if they are not removed quickly. Use a clean cloth and vinyl cleaner. See your dealer for this product.


Leather Use a soft cloth with lukewarm water and a mild soap or saddle soap and wipe dry with a soft cloth. Then, let the leather dry naturally. Do not use heat to dry.


For stubborn stains, use a leather cleaner.


(cid:127) Never use oils, varnishes, solvent-based or abrasive cleaners, furniture polish, or shoe polish on leather.


(cid:127) Soiled or stained leather should be cleaned


immediately. If dirt is allowed to work into the finish, it can harm the leather.


Instrument Panel Use only mild soap and water to clean the top surfaces of the instrument panel. Sprays containing silicones or waxes may cause annoying reflections in the windshield and even make it difficult to see through the windshield under certain conditions.


Interior Plastic Components Use only a mild soap and water solution on a soft cloth or sponge. Commercial cleaners may affect the surface finish.


5-85


(cid:127) (cid:127) Speaker Covers Vacuum around a speaker cover gently, so that the speaker will not be damaged. Clean spots with just water and mild soap.


Glass Surfaces Glass should be cleaned often. GM Glass Cleaner or a liquid household glass cleaner will remove normal tobacco smoke and dust films on interior glass. See Vehicle Care/Appearance Materials on page 5-90. Notice: glass surfaces on your vehicle, you could scratch the glass and/or cause damage to the rear window defogger and the integrated radio antenna. When cleaning the glass on your vehicle, use only a soft cloth and glass cleaner.


If you use abrasive cleaners when cleaning


Care of Safety Belts Keep belts clean and dry.


{CAUTION:


Do not bleach or dye safety belts. If you do, it may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.


Weatherstrips Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth. During very cold, damp weather frequent application may be required. See Part D: Recommended Fluids and Lubricants on page 6-25.


5-86


Washing Your Vehicle The paint finish on the vehicle provides beauty, depth of color, gloss retention, and durability. The best way to preserve the vehicle’s finish is to keep it clean by washing it often with lukewarm or cold water. Do not wash the vehicle in the direct rays of the sun. Use a car washing soap. Do not use strong soaps or chemical detergents. Be sure to rinse the vehicle well, removing all soap residue completely. GM-approved cleaning products can be obtained from your dealer. See Vehicle Care/Appearance Materials on page 5-90. Do not use cleaning agents that are petroleum based, or that contain acid or abrasives. All cleaning agents should be flushed promptly and not allowed to dry on the surface, or they could stain. Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting. High pressure car washes may cause water to enter the vehicle.


Cleaning Exterior Lamps/Lenses Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under Washing Your Vehicle on page 5-87.


Finish Care Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint finish. GM-approved cleaning products can be obtained from your dealer. See Vehicle Care/Appearance Materials on page 5-90. The vehicle has a “basecoat/clearcoat” paint finish. The clearcoat gives more depth and gloss to the colored basecoat. Always use waxes and polishes that are non-abrasive and made for a basecoat/clearcoat paint finish. Notice: Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/clearcoat paint finish on your vehicle. Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage the vehicle’s finish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter. Exterior painted surfaces are subject to aging, weather, and chemical fallout that can take their toll over a period of years. To help keep the paint finish looking new, keep the vehicle in a garage or covered whenever possible.


5-87


The surface of these wheels is similar to the painted surface of your vehicle. Do not use strong soaps, chemicals, abrasive polishes, abrasive cleaners, cleaners with acid, or abrasive cleaning brushes on them because you could damage the surface. Do not use chrome polish on aluminum wheels. Use chrome polish only on chrome-plated wheels, but avoid any painted surface of the wheel, and buff off immediately after application. Do not take your vehicle through an automatic car wash that has silicone carbide tire cleaning brushes. These brushes can also damage the surface of these wheels.


Tires To clean the tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on your vehicle may damage the paint finish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on your vehicle.


Windshield and Wiper Blades If the windshield is not clear after using the windshield washer, or if the wiper blade chatters when running, wax, sap, or other material may be on the blade or windshield. Clean the outside of the windshield with a full-strength glass cleaning liquid. The windshield is clean if beads do not form when you rinse it with water. Grime from the windshield will stick to the wiper blades and affect their performance. Clean the blade by wiping vigorously with a cloth soaked in full-strength windshield washer solvent. Then rinse the blade with water. Check the wiper blades and clean them as necessary; replace blades that look worn.


Aluminum or Chrome-Plated Wheels Your vehicle may be equipped with either aluminum or chrome-plated wheels. Keep your wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied.


5-88


At least every spring, flush these materials from the underbody with plain water. Clean any areas where mud and debris can collect. Dirt packed in close areas of the frame should be loosened before being flushed. Your GM dealer or an underbody car washing system can do this for you.


Chemical Paint Spotting Some weather and atmospheric conditions can create a chemical fallout. Airborne pollutants can fall upon and attack painted surfaces on the vehicle. This damage can take two forms: blotchy, ring-shaped discolorations, and small, irregular dark spots etched into the paint surface. Although no defect in the paint job causes this, GM will repair, at no charge to the owner, the surfaces of new vehicles damaged by this fallout condition within 12 months or 12,000 miles (20 000 km) of purchase, whichever occurs first.


Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the warranty.


Finish Damage Any stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into major repair expense. Minor chips and scratches can be repaired with touch-up materials available from your GM dealer. Larger areas of finish damage can be corrected in your GM dealer’s body and paint shop.


Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not removed, corrosion and rust can develop on the underbody parts such as fuel lines, frame, floor pan, and exhaust system even though they have corrosion protection.


5-89


Vehicle Care/Appearance Materials See your GM dealer for more information on purchasing the following products.


Description


Usage


Interior and exterior polishing cloth. Removes tar, road oil and asphalt. Use on chrome or stainless steel. Removes soil and black marks from whitewalls. Cleans vinyl tops, upholstery and convertible tops. Removes dirt, grime, smoke and fingerprints. Removes dirt and grime from chrome wheels and wire wheel covers. Removes dust, fingerprints, and surface contaminants. Spray on wipe off.


Polishing Cloth Wax-Treated Tar and Road Oil Remover Chrome Cleaner and Polish White Sidewall Tire Cleaner


Vinyl Cleaner


Glass Cleaner


Chrome and Wire Wheel Cleaner


Finish Enhancer


5-90


Description


Usage


Cleaner Wax


Swirl Remover Polish


Wash Wax Concentrate


Foaming Tire Shine Low Gloss


Removes swirl marks, fine scratches and other light surface contamination. Removes light scratches and protects finish. Cleans, shines and protects in one easy step, no wiping necessary. Medium foaming shampoo. Cleans and lightly waxes. Biodegradable and phosphate free. Quickly and easily removes spots and stains from carpets, vinyl and cloth upholstery. Odorless spray odor eliminator used on fabrics, vinyl, leather and carpet. See your General Motors parts department for these products. See Part D: Recommended Fluids and Lubricants on page 6-25.


Odor Eliminator


Spot Lifter


Vehicle Identification


Vehicle Identification Number (VIN)


This is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle. The VIN also appears on the Vehicle Certification and Service Parts labels and the certificates of title and registration. Engine Identification The 8th character in your VIN is the engine code. This code will help you identify your engine, specifications and replacement parts.


Service Parts Identification Label You will find this label on your spare tire cover. It is very helpful if you ever need to order parts. On this label, you will find the following: (cid:127) VIN (cid:127) Model designation (cid:127) Paint information (cid:127) Production options and special equipment Be sure that this label is not removed from the vehicle. Electrical System


Add-On Electrical Equipment Notice: Don’t add anything electrical to your vehicle unless you check with your dealer first. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should. Your vehicle has an air bag system. Before attempting to add anything electrical to your vehicle, see Servicing Your Airbag-Equipped Vehicle on page 1-57.


5-91


Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses and circuit breakers. This greatly reduces the chance of fires caused by electrical problems. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure you replace a bad fuse with a new one of the identical size and rating. If you ever have a problem on the road and don’t have a spare fuse, you can borrow one that has the same amperage. Just pick some feature of your vehicle that you can get along without — like the radio or cigarette lighter— and use its fuse, if it is the correct amperage. Replace it as soon as you can.


Main Instrument Panel Fuse Block The main instrument panel fuse block is located under the instrument panel, on the passenger’s side of the vehicle. Lamps, connectors and the HVAC duct temperature sensors may need to be disconnected and removed to allow access to this fuse block. Remove the hush panel on the passenger’s side to reveal the fuses by performing the following steps: 1. Remove the two screws located along the front


edge of the panel.


2. Lower the hush panel. 3. Remove the fuse block cover. 4. Place the wide end of the fuse puller over the


plastic end of the fuse.


5. Squeeze the ends over the fuse and pull it out. When finished, reinstall the fuse block cover and the hush panel. Reinstall lamps, connectors and HVAC duct temperature sensors if they were removed.


5-92


Fuses ABS


HVAC


CR CONT


HUD


CSTR/SBM


LP PK L


LP PK R


RUN WSW Blank


Usage


Anti-Lock Brake System Module HVAC Main Con Head, HVAC Programmer, Instrument Panel Cluster Stepper Motor Cruise, Cruise Switch Head-Up Display Switch, Head-Up Display HVAC Programmer, Instrument Panel Cluster, SBM (275 to LCM) (1135 to BTSI SL) Underhood Lamp, Left Park/Sidemarker, Left Park/Turn Lamp, SBM, Left Tail Signal Lamp, Left Tail/Stoplamp, Left Rear Sidemarker Right Park/Sidemarker Lamp, Right Park/Turn Lamp, Right Tail/Sign Lamp, Right Tail/Stoplamp, Right Rear Sidemarker, Stop/Taillamp, Tail/Signal Lamp, License Lamp, RFA Run/Accessory Wiper Motor Not Used


WSW/RFA Wiper Switch, RFA, Rain Sense


B/U LP


Auto Dimming Mirror, Back-Up Lamps


5-93


Fuses SBM PDM A/C


IGN SEN


ELC


Usage


Interior Lamps PDM Module HVAC Motor, HVAC Mix Motors Auto Dimming Mirror, Driver HTS Seat, Rear Defog Relay, MEM Module, Cool LVL Sensor, Passenger Heated Seat HVAC Flat Pk Mtrs, Electronic Level Control Sensor, Electronic Level Control Sensor (Rear Fuse Block)


Auxiliary Instrument Panel Fuse Block The auxiliary instrument panel fuse block is located under the instrument panel, on the passenger’s side of the vehicle. Lamps, connectors and the HVAC duct temperature sensors may need to be disconnected and removed to allow access to this fuse block. Remove the hush panel on the passenger’s side to reveal the fuses by performing the following steps: 1. Remove the two screws located along the front


edge of the panel.


2. Lower the hush panel. 3. Remove the fuse block cover. 4. Place the wide end of the fuse puller over the


plastic end of the fuse.


5. Squeeze the ends over the fuse and pull it out. When finished, reinstall the fuse block cover and the hush panel. Reinstall lamps, connectors and HVAC duct temperature sensors if they were removed.


5-94


Fuses


PERIM LP


ACCY IGN 3


Usage


Perimeter Lamps Accessory Ignition 3


Underhood Fuse Block


There are additional fuses located in the engine compartment on the passenger’s side of the vehicle. See Engine Compartment Overview on page 5-12
for more information on location. To check the fuses in this underhood fuse block, turn the knob counterclockwise and remove the cover.


Fuses


Usage


10


Not Used SBM, LCM Turn Signal Pre-Oxygen Sensor, Post-Oxygen Sensor Air Bag (SIR) Powertrain Control Module Air Conditioning Clutch Ignition Feed Horn Relay Spare


5-95


32
33
34
35
36
37


Usage


Starter Not Used Cooling Fan SP Cooling Fan 2
Air Conditioning Clutch Fuel Pump


Fuses


Usage


38
39
40
41
42
43
44
45
46


Bat #1
Blower Motor Cooling Fan 1
Headlamp BAT #2
Ignition Starter ABS Fuse Puller


Fuses


Usage


Relays


11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28


Spare Injectors #1-6
C-31
Right High Beam Spare Left High Beam Spare Right Low Beam Left Low Beam Stop Fuel Pump Relay (Wire in BEC) Run/Crank Powertrain Control Module Parking Lamps Hazard Flashers Spare Spare ABS #2


Relays


29
30
31


Ignition Horn Cooling Fan 1


Usage


5-96


Rear Compartment Fuse Block Additional fuses are located in the fuse center under the rear seat. The rear seat cushion must be removed to access the fuses. See “Removing the Rear Seat Cushion” following for more information.


Circuit Breakers Usage


Power Seat Electronic Level Control Sensor, Electronic Level Control Compressor Solenoid


Fuses


10
11
12
13
14
15
16
17
18
19
20
21


22


Usage Crank Accessory Outlet Powertrain Control Module for Cruise SBM Module Radio/Phone Sunroof Spare CD Changer, Phone Driver Door Module Spare Radio Driver Heated Seat Module Rear Door Module Trunk Release Spare Instrument Panel Ashtray Cigarette Lighter


5-97


Relays


Usage


Heated Backlite Retained Accessory Power (RAP) Trunk Release Electronic Level Control


To reinstall the rear seat cushion, do the following:


{CAUTION:


A safety belt that is not properly routed through the seat cushion or is twisted will not provide the protection needed in a crash. If the safety belt has not been routed through the seat cushion at all, it will not be there to work for the next passenger. The person sitting in that position could be badly injured. After reinstalling the seat cushion, always check to be sure that the safety belts are properly routed and are not twisted.


Fuses


23
24
25
26
27


28


Usage Spare Spare Passenger Heated Seat Module Right Rear Cig Lighter Left Rear Cig Lighter RFA, Memory Seat Module, Driver Seat Switch


Removing the Rear Seat Cushion Notice: If, when removing or reinstalling the rear seat, you do not do it carefully, you could damage the fuse center. Avoid contact between the rear seat and the fuse center whenever you remove or reinstall the rear seat. To remove the rear seat cushion, do the following: 1. Pull up on the front of the cushion to release the


front hooks.


2. Pull the cushion up and out toward the front of


the vehicle.


5-98


2. Slide the rear of the cushion up and under the seatback so the rear locating guides hook into the wire loops on the back frame.


3. With the seat cushion lowered, push rearward and


then press down on the seat cushion until the spring locks on both ends engage.


4. Check to make sure the safety belts are properly


routed and that no portion of any safety belt is trapped under the seat. Also make sure the seat cushion is secured.


5-99


1. Buckle the center passenger position safety belt,


then route the safety belts through the proper slots in the seat cushion. Do not let the safety belts get twisted.


Capacities and Specifications The following approximate capacities are given in English and metric conversions. Please refer to Part D: Recommended Fluids and Lubricants on page 6-25 for more information.


Capacities


Application


English 2.2 lbs


Air Conditioning Refrigerant R134a Automatic Transaxle Engine Cooling System Engine Oil with Filter Fuel Tank Wheel Nut Torque All capacities are approximate. When adding, be sure to fill to the appropriate level, as recommended in this manual.


7.4 quarts 13.0 quarts 4.5 quarts 18.5 gallons


100 ft lb


Metric 1.0 kg 7.0 L 12.3 L 4.3 L 70.0 L 140 Y


Engine


3800 3.8L V6
3800 3.8L V6
Supercharged


VIN Code


Transaxle Automatic


Automatic


Spark Plug Gap


0.060 inch (0.152 cm)


0.060 inch (0.152 cm)


5-100


Normal Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your GM dealer.


Normal Maintenance Replacement Parts


Part


GM Part Number


Engine Air Cleaner/Filter Engine Oil Filter Fuel Filter Passenger Compartment Air Filter Spark Plugs Windshield Wiper Blades (Hook Type) 22.0 inches (56.0 cm)


25096932
25010792
25121293
52472175
12568387


12463075


ACDelco® Part


Number A1096C


PF47
GF627



41–101



5-101


Engine Drive Belt Routing


3.8L V6 Engine


3.8L V6 Supercharged Engine


5-102


Section 6


Maintenance Schedule


Maintenance Schedule ......................................6-2
Introduction ...................................................6-2
Maintenance Requirements ..............................6-2
Your Vehicle and the Environment ....................6-2
How This Section is Organized .........................6-3
Part A: Scheduled Maintenance Services ...........6-4
Using Your Maintenance Schedule ....................6-4
Selecting the Right Schedule ...........................6-5
Short Trip/City Scheduled Maintenance ..............6-6
Long Trip/Highway Scheduled Maintenance ......6-13
Part B: Owner Checks and Services ................6-19
At Each Fuel Fill ..........................................6-19
At Least Once a Month .................................6-19


At Least Twice a Year ...................................6-20
At Least Once a Year ...................................6-20
Part C: Periodic Maintenance Inspections .........6-23
Steering, Suspension and Front Drive Axle


Boot and Seal Inspection ............................6-23
Exhaust System Inspection ............................6-23
Fuel System Inspection ..................................6-23
Engine Cooling System Inspection ...................6-24
Throttle System Inspection .............................6-24
Brake System Inspection ................................6-24
Part D: Recommended Fluids and Lubricants ....6-25
Part E: Maintenance Record ...........................6-27


6-1


Maintenance Schedule


Introduction Important: Keep engine oil at the proper level and change as recommended.


Have you purchased the GM Protection Plan? The Plan supplements your new vehicle warranties. See your Warranty and Owner Assistance booklet or your dealer for details.


Maintenance Requirements Maintenance intervals, checks, inspections and recommended fluids and lubricants as prescribed in this manual are necessary to keep your vehicle in good working condition. Any damage caused by failure to follow scheduled maintenance may not be covered by warranty.


Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep your vehicle in good working condition, but also helps the environment. Improper vehicle maintenance can even affect the quality of the air we breathe. Improper fluid levels or the wrong tire inflation can increase the level of emissions from your vehicle. To help protect our environment, and to keep your vehicle in good condition, be sure to maintain your vehicle properly.


6-2


“Part B: Owner Checks and Services” tells you what should be checked and when. It also explains what you can easily do to help keep your vehicle in good condition. “Part C: Periodic Maintenance Inspections” explains important inspections that your dealer’s service department can perform for you. “Part D: Recommended Fluids and Lubricants” lists some recommended products necessary to help keep your vehicle properly maintained. These products, or their equivalents, should be used whether you do the work yourself or have it done. “Part E: Maintenance Record” is a place for you to record and keep track of the maintenance performed on your vehicle. Keep your maintenance receipts. They may be needed to qualify your vehicle for warranty repairs.


How This Section is Organized This maintenance schedule is divided into five parts: “Part A: Scheduled Maintenance Services” explains what to have done and how often. Some of these services can be complex, so unless you are technically qualified and have the necessary equipment, you should let your GM dealer’s service department do these jobs. Your GM dealer has GM-trained and supported service people that will perform the work using genuine GM parts.


{CAUTION:


Performing maintenance work on a vehicle can be dangerous. In trying to do some jobs, you can be seriously injured. Do your own maintenance work only if you have the required know-how and the proper tools and equipment for the job. If you have any doubt, have a qualified technician do the work.


If you want to get the service information, see Service Publications Ordering Information on page 7-11.


6-3


Part A: Scheduled Maintenance Services In this part are scheduled maintenance services which are to be performed at the mileage intervals specified.


Using Your Maintenance Schedule We at General Motors want to keep your vehicle in good working condition. But we do not know exactly how you will drive it. You may drive short distances only a few times a week. Or you may drive long distances all the time in very hot, dusty weather. You may use your vehicle in making deliveries. Or you may drive it to work, to do errands or in many other ways. Because of the different ways people use their vehicles, maintenance needs may vary. You may need more frequent checks and replacements. So please read the following and note how you drive. If you have questions on how to keep your vehicle in good condition, see your dealer.


This part tells you the maintenance services you should have done and when to schedule them. When you go to your dealer for your service needs, you will know that GM-trained and supported service people will perform the work using genuine GM parts. The proper fluids and lubricants to use are listed in Part D. Make sure whoever services your vehicle uses these. All parts should be replaced and all necessary repairs done before you or anyone else drives the vehicle. These schedules are for vehicles that:


carry passengers and cargo within recommended limits. You will find these on the tire and loading information label. See Loading Your Vehicle on page 4-30. are driven on reasonable road surfaces within legal driving limits. use the recommended fuel. See Gasoline Octane on page 5-4.


6-4


(cid:127) (cid:127) (cid:127) Selecting the Right Schedule First you will need to decide which of the two schedules is right for your vehicle. Here is how to decide which schedule to follow: Short Trip/City Definition Follow the Short Trip/City Scheduled Maintenance if any one of these conditions is true for your vehicle: (cid:127) Most trips are less than 5 miles (8 km). This is


particularly important when outside temperatures are below freezing.


(cid:127) Most trips include extensive idling (such as frequent


driving in stop-and-go traffic).


(cid:127) You frequently tow a trailer or use a carrier on top


of your vehicle. If the vehicle is used for delivery service, police, taxi or other commercial application.


One of the reasons you should follow this schedule if you operate your vehicle under any of these conditions is that these conditions cause engine oil to break down sooner.


Short Trip/City Intervals


Every 3,000 Miles (5 000 km): Engine Oil and Filter Change (or 3 months, whichever occurs first).


Every 6,000 Miles (10 000 km): Tire Rotation.


Every 15,000 Miles (25 000 km): Engine Air Cleaner Filter Inspection. Passenger Compartment Air Filter Replacement.


Every 30,000 Miles (50 000 km): Engine Air Cleaner Filter Replacement. Supercharger Oil Check (or every 36 months, whichever occurs first) (3800 Code 1
V6 engine only).


Every 50,000 Miles (83 000 km): Automatic Transaxle Service (severe conditions only).


Every 100,000 Miles (166 000 km): Spark Plug Wire Inspection. Spark Plug Replacement. Automatic Transaxle Service (normal conditions).


Every 150 000 Miles (240 000 km): Cooling System Service (or every 60 months, whichever occurs first). Engine Accessory Drive Belt Inspection. These intervals only summarize maintenance services. Be sure to follow the complete scheduled maintenance on the following pages.


6-5


(cid:127) Long Trip/Highway Definition Follow this scheduled maintenance only if none of the conditions from the Short Trip/City Scheduled Maintenance are true. Do not use this schedule if the vehicle is used for trailer towing, driven in a dusty area or used off paved roads. Use the Short Trip/City schedule for these conditions Driving a vehicle with a fully warmed engine under highway conditions will cause engine oil to break down slower. Long Trip/Highway Intervals


Every 7,500 Miles (12 500 km): Engine Oil and Filter Change (or every 12 months, whichever occurs first). Tire Rotation.


Every 15,000 Miles (25 000 km): Engine Air Cleaner Filter Inspection. Passenger Compartment Air Filter Replacement.


Every 30,000 Miles (50 000 km): Supercharger Oil Check (or every 36 months, whichever occurs first) (3800 Code 1 V6 engine only). Engine Air Cleaner Filter Replacement.


Every 50,000 Miles (83 000 km): Automatic Transaxle Service (severe conditions only).


6-6


Every 100,000 Miles (166 000 km): Spark Plug Wire Inspection. Spark Plug Replacement. Automatic Transaxle Service (normal conditions).


Every 150,000 Miles (240 000 km): Cooling System Service (or every 60 months, whichever occurs first). Engine Accessory Drive Belt Inspection. These intervals only summarize maintenance services. Be sure to follow the complete scheduled maintenance on the following pages.


Short Trip/City Scheduled Maintenance The services shown in this schedule up to 100,000 miles (166 000 km) should be repeated after 100,000 miles (166 000 km) at the same intervals for the life of this vehicle. The services shown at 150,000 miles (240 000 km) should be repeated at the same interval after 150,000 miles (240 000 km) for the life of this vehicle. See Part B: Owner Checks and Services on page 6-19
and Part C: Periodic Maintenance Inspections on page 6-23.


Footnotes † The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of the vehicle’s useful life. We, however, urge that all recommended maintenance services be performed at the indicated intervals and the maintenance be recorded. * If your vehicle has the GM Oil Life System, a computer system lets you know when to change the oil and filter. This is based on engine revolutions and engine temperature, and not on mileage. Based on driving conditions, the mileage at which an oil change will be indicated can vary considerably. For the oil life system to work properly, you must reset the system every time the oil is changed. When the system has calculated that oil life has been diminished, it will indicate that an oil change is necessary. A CHANGE ENGINE OIL SOON message will come on. Change your oil as soon as possible within the next two times you stop for fuel. See Engine Oil on page 5-13. It is possible that, if you are driving under the best conditions, the oil life system may not indicate that an oil change is necessary for over a year. However, your engine oil and filter must be changed at


least once a year and at this time the system must be reset. It is also important to check your oil regularly and keep it at the proper level. If the system is ever reset accidentally, you must change your oil at 3,000 miles (5 000 km) since your last oil change. Remember to reset the oil life system whenever the oil is changed. See Engine Oil Life System on page 5-17 for information on resetting the system. @ Whenever the tires are rotated, the Check Tire Pressure System (if equipped) must be reset. + A good time to check your brakes is during tire rotation. See Brake System Inspection on page 6-24. 3,000 Miles (5 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


6,000 Miles (10 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


6-7


9,000 Miles (15 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


12,000 Miles (20 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


15,000 Miles (25 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.) Inspect engine air cleaner filter. If necessary, replace the filter. If vehicle is driven in dusty/dirty conditions, inspect filter at every engine oil change. See Engine Air Cleaner/Filter on page 5-19 for more information. An Emission Control Service. (See footnote †.)


❑ Replace passenger compartment air filter.


18,000 Miles (30 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


21,000 Miles (35 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


24,000 Miles (40 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


27,000 Miles (45 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


6-8


❑ 30,000 Miles (50 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Replace passenger compartment air filter. ❑ Replace engine air cleaner filter. See Engine Air Cleaner/Filter on page 5-19 for more information. An Emission Control Service. For supercharged engine only: Check the supercharger oil level and add the proper supercharger oil as needed (or every 36 months, whichever occurs first). See Part D: Recommended Fluids and Lubricants on page 6-25. An Emission Control Service. (See footnote †.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


33,000 Miles (55 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


36,000 Miles (60 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


39,000 Miles (65 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


42,000 Miles (70 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


6-9


❑ 45,000 Miles (75 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Replace passenger compartment air filter.


Inspect engine air cleaner filter. If necessary, replace the filter. If vehicle is driven in dusty/dirty conditions, inspect filter at every engine oil change. See Engine Air Cleaner/Filter on page 5-19 for more information. An Emission Control Service. (See footnote †.)


48,000 Miles (80 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


50,000 Miles (83 000 km) ❑ Change automatic transaxle fluid and filter if the


vehicle is mainly driven under one or more of these conditions:


− In heavy city traffic where the outside


temperature regularly reaches 90°F (32°C) or higher.


6-10


− In hilly or mountainous terrain. − When doing frequent trailer towing. − Uses such as found in taxi, police or


delivery service.


If you do not use your vehicle under any of these conditions, change the fluid and filter at 100,000 miles (166 000 km). 51,000 Miles (85 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


54,000 Miles (90 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


57,000 Miles (95 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ 60,000 Miles (100 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Replace passenger compartment air filter. ❑ Replace engine air cleaner filter. See Engine Air Cleaner/Filter on page 5-19 for more information. An Emission Control Service. For supercharged engines only: Check the supercharger oil level and add the proper supercharger oil as needed (or every 36 months, whichever occurs first). See Part D: Recommended Fluids and Lubricants on page 6-25. An Emission Control Service. (See footnote †.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


63,000 Miles (105 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


66,000 Miles (110 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


69,000 Miles (115 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


72,000 Miles (120 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


75,000 Miles (125 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.) Inspect engine air cleaner filter. If necessary, replace the filter. If vehicle is driven in dusty/dirty conditions, inspect filter at every engine oil change. See Engine Air Cleaner/Filter on page 5-19 for more information. An Emission Control Service. (See footnote †.)


❑ Replace passenger compartment air filter.


6-11


❑ ❑ 78,000 Miles (130 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


81,000 Miles (135 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


84,000 Miles (140 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


87,000 Miles (145 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


6-12


90,000 Miles (150 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Replace passenger compartment air filter. ❑ Replace engine air cleaner filter. See Engine Air Cleaner/Filter on page 5-19 for more information. An Emission Control Service. For supercharged engines only: Check the supercharger oil level and add the proper supercharger oil as needed (or every 36 months, whichever occurs first). See Part D: Recommended Fluids and Lubricants on page 6-25. An Emission Control Service. (See footnote †.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


93,000 Miles (155 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ 96,000 Miles (160 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


99,000 Miles (165 000 km) ❑ Change engine oil and filter (or every 3 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


100,000 Miles (166 000 km)


Inspect spark plug wires. An Emission Control Service.


❑ Replace spark plugs. An Emission Control Service. ❑ Change automatic transaxle fluid and filter if the


vehicle is mainly driven under one or more of these conditions:


− In heavy city traffic where the outside


temperature regularly reaches 90°F (32°C) or higher.


− In hilly or mountainous terrain. − When doing frequent trailer towing. − Uses such as found in taxi, police or


delivery service.


If you have not used your vehicle under severe service conditions listed previously and, therefore, have not changed your automatic transaxle fluid, change both the fluid and filter.


150,000 Miles (240 000 km) ❑ Drain, flush and refill cooling system (or every


60 months since last service, whichever occurs first). See Engine Coolant on page 5-24 for what to use. Inspect hoses. Clean radiator, condenser, pressure cap and neck. Pressure test cooling system and pressure cap. An Emission Control Service. Inspect engine accessory drive belt. An Emission Control Service.


Long Trip/Highway Scheduled Maintenance The services shown in this schedule up to 100,000 miles (166 000 km) should be repeated after 100,000 miles (166 000 km) at the same intervals for the life of this vehicle. The services shown at 150,000 miles (240 000 km) should be repeated at the same interval after 150,000 miles (240 000 km) for the life of this vehicle. See Part B: Owner Checks and Services on page 6-19
and Part C: Periodic Maintenance Inspections on page 6-23.


6-13


❑ ❑ ❑ However, your engine oil and filter must be changed at least once a year and at this time the system must be reset. It is also important to check your oil regularly and keep it at the proper level. If the system is ever reset accidentally, you must change your oil at 3,000 miles (5 000 km) since your last oil change. Remember to reset the oil life system whenever the oil is changed. See Engine Oil Life System on page 5-17 for information on resetting the system. @ Whenever the tires are rotated, the Check Tire Pressure System (if equipped) must be reset. + A good time to check your brakes is during tire rotation. See Brake System Inspection on page 6-24. 7,500 Miles (12 500 km) ❑ Change engine oil and filter (or every 12 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


Footnotes † The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of the vehicle’s useful life. We, however, urge that all recommended maintenance services be performed at the indicated intervals and the maintenance be recorded. * If your vehicle has the GM Oil Life System, a computer system lets you know when to change the engine oil and filter. This is based on engine revolutions and engine temperature, and not on mileage. Based on driving conditions, the mileage at which an oil change will be indicated can vary considerably. For the oil life system to work properly, you must reset the system every time the oil is changed. When the system has calculated that oil life has been diminished, it will indicate that an oil change is necessary. A CHANGE ENGINE OIL SOON message will come on. Change your oil as soon as possible within the next two times you stop for fuel. See Engine Oil on page 5-13. It is possible that, if you are driving under the best conditions, the oil life system may not indicate that an oil change is necessary for over a year.


6-14


15,000 Miles (25 000 km) ❑ Change engine oil and filter (or every 12 months,


whichever occurs first). An Emission Control Service. (See footnote *.) Inspect engine air cleaner filter. See Engine Air Cleaner/Filter on page 5-19 for more information. An Emission Control Service. (See footnote †.)


❑ Replace passenger compartment air filter. ❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


22,500 Miles (37 500 km) ❑ Change engine oil and filter (or every 12 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.) ❑ Replace engine air cleaner filter. See Engine Air Cleaner/Filter on page 5-19 for more information. An Emission Control Service. For supercharged engines only: Check the supercharger oil level and add the proper supercharger oil as needed (or every 36 months, whichever occurs first). See Part D: Recommended Fluids and Lubricants on page 6-25. An Emission Control Service. (See footnote †.)


37,500 Miles (62 500 km) ❑ Change engine oil and filter (or every 12 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


30,000 Miles (50 000 km) ❑ Change engine oil and filter (or every 12 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Replace passenger compartment air filter.


6-15


❑ ❑ 45,000 Miles (75 000 km) ❑ Change engine oil and filter (or every 12 months,


whichever occurs first). An Emission Control Service. (See footnote *.) Inspect engine air cleaner filter. See Engine Air Cleaner/Filter on page 5-19 for more information. An Emission Control Service. (See footnote †.)


❑ Replace passenger compartment air filter. ❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


50,000 Miles (83 000 km) ❑ Change automatic transaxle fluid and filter if the


vehicle is mainly driven under one or more of these conditions:


− In heavy city traffic where the outside


temperature regularly reaches 90°F (32°C) or higher.


− In hilly or mountainous terrain. − When doing frequent trailer towing. − Uses such as found in taxi, police or


delivery service.


If you do not use your vehicle under any of these conditions, change the fluid and filter at 100,000 miles (166 000 km).


6-16


52,500 Miles (87 500 km) ❑ Change engine oil and filter (or every 12 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


60,000 Miles (100 000 km) ❑ Change engine oil and filter (or every 12 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Replace passenger compartment air filter. For supercharged engines only: Check the supercharger oil level and add the proper supercharger oil as needed (or every 36 months, whichever occurs first). See Part D: Recommended Fluids and Lubricants on page 6-25. An Emission Control Service. (See footnote †.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.) ❑ Replace engine air cleaner filter. See Engine Air Cleaner/Filter on page 5-19 for more information. An Emission Control Service.


❑ ❑ 67,500 Miles (112 500 km) ❑ Change engine oil and filter (or every 12 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


75,000 Miles (125 000 km) ❑ Change engine oil and filter (or every 12 months,


whichever occurs first). An Emission Control Service. (See footnote *.) Inspect engine air cleaner filter. See Engine Air Cleaner/Filter on page 5-19 for more information. An Emission Control Service. (See footnote †.)


❑ Replace passenger compartment air filter. ❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


82,500 Miles (137 500 km) ❑ Change engine oil and filter (or every 12 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


90,000 Miles (150 000 km) ❑ Change engine oil and filter (or every 12 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Replace passenger compartment air filter. ❑ Replace engine air cleaner filter. See Engine Air Cleaner/Filter on page 5-19 for more information. An Emission Control Service. For supercharged engines only: Check the supercharger oil level and add the proper supercharger oil as needed (or every 36 months, whichever occurs first). See Part D: Recommended Fluids and Lubricants on page 6-25. An Emission Control Service. (See footnote †.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


97,500 Miles (162 500 km) ❑ Change engine oil and filter (or every 12 months,


whichever occurs first). An Emission Control Service. (See footnote *.)


❑ Rotate tires. See Tire Inspection and Rotation on


page 5-67 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.)


6-17


❑ ❑ 150,000 Miles (240 000 km) ❑ Drain, flush and refill cooling system (or every


60 months since last service, whichever occurs first). See Engine Coolant on page 5-24 for what to use. Inspect hoses. Clean radiator, condenser, pressure cap and neck. Pressure test the cooling system and pressure cap. An Emission Control Service. Inspect engine accessory drive belt. An Emission Control Service.


100,000 Miles (166 000 km)


Inspect spark plug wires. An Emission Control Service.


❑ Replace spark plugs. An Emission Control Service. ❑ Change automatic transaxle fluid and filter if the


vehicle is mainly driven under one or more of these conditions:


− In heavy city traffic where the outside


temperature regularly reaches 90°F (32°C) or higher.


− In hilly or mountainous terrain. − When doing frequent trailer towing. − Uses such as found in taxi, police or


delivery service.


If you have not used your vehicle under severe service conditions listed previously and, therefore, have not changed your automatic transaxle fluid, change both the fluid and filter


6-18


❑ ❑ ❑ Part B: Owner Checks and Services Listed in this part are owner checks and services which should be performed at the intervals specified to help ensure the safety, dependability and emission control performance of your vehicle. Be sure any necessary repairs are completed at once. Whenever any fluids or lubricants are added to your vehicle, make sure they are the proper ones, as shown in Part D.


At Each Fuel Fill It is important for you or a service station attendant to perform these underhood checks at each fuel fill. Engine Oil Level Check Check the engine oil level and add the proper oil if necessary. See Engine Oil on page 5-13 for further details.


Engine Coolant Level Check Check the engine coolant level and add DEX-COOL® coolant mixture if necessary. See Engine Coolant on page 5-24 for further details. Windshield Washer Fluid Level Check Check the windshield washer fluid level in the windshield washer tank and add the proper fluid if necessary. See Windshield Washer Fluid on page 5-35 for further details.


At Least Once a Month Tire Inflation Check Visually inspect your tires and make sure tires are inflated to the correct pressures. Do not forget to check your spare tire. See Tires on page 5-58 for further details. Cassette Tape Player Service Clean cassette tape player. Cleaning should be done every 50 hours of tape play. See Audio System(s) on page 3-55 for further details.


6-19


Automatic Transaxle Check Check the transaxle fluid level; add if needed. See Automatic Transaxle Fluid on page 5-22. A fluid loss may indicate a problem. Check the system and repair if needed.


At Least Once a Year Key Lock Cylinders Service Lubricate the key lock cylinders with the lubricant specified in Part D. Body Lubrication Service Lubricate all body door hinges. Also lubricate all hinges and latches, including those for the hood, glove box door and console door. Part D tells you what to use. More frequent lubrication may be required when exposed to a corrosive environment.


At Least Twice a Year Restraint System Check Make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired. Have any torn or frayed safety belts replaced. Also look for any opened or broken air bag coverings, and have them repaired or replaced. (The air bag system does not need regular maintenance.) Wiper Blade Check Inspect wiper blades for wear or cracking. Replace blade inserts that appear worn or damaged or that streak or miss areas of the windshield. Also see Windshield and Wiper Blades on page 5-88. Weatherstrip Lubrication Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth. During very cold, damp weather more frequent application may be required. See Part D: Recommended Fluids and Lubricants on page 6-25.


6-20


Starter Switch Check


{CAUTION:


When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured.


1. Before you start, be sure you have enough room


around the vehicle.


2. Firmly apply both the parking brake and the


regular brake. See Parking Brake on page 2-29
if necessary. Do not use the accelerator pedal, and be ready to turn off the engine immediately if it starts.


3. Try to start the engine in each gear. The starter should work only in PARK (P) or NEUTRAL (N). If the starter works in any other position, your vehicle needs service.


Automatic Transaxle Shift Lock Control System Check


{CAUTION:


When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured.


1. Before you start, be sure you have enough


room around the vehicle. It should be parked on a level surface.


2. Firmly apply the parking brake. See Parking Brake


on page 2-29 if necessary. Be ready to apply the regular brake immediately if the vehicle begins to move.


3. With the engine off, turn the ignition to RUN, but do


not start the engine. Without applying the regular brake, try to move the shift lever out of PARK (P) with normal effort. If the shift lever moves out of PARK (P), your vehicle needs service.


6-21


Ignition Transaxle Lock Check While parked, and with the parking brake set, try to turn the ignition key to LOCK in each shift lever position.


The ignition should turn to LOCK only when the shift lever is in PARK (P). The key should come out only in LOCK.


Parking Brake and Automatic Transaxle Park (P) Mechanism Check


{CAUTION:


When you are doing this check, your vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of your vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move.


Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake.


To check the parking brake’s holding ability: With the engine running and transaxle in NEUTRAL (N), slowly remove foot pressure from the regular brake pedal. Do this until the vehicle is held by the parking brake only. To check the PARK (P) mechanism’s holding ability: With the engine running, shift to PARK (P). Then release the parking brake followed by the regular brake.


Underbody Flushing Service At least every spring, use plain water to flush any corrosive materials from the underbody. Take care to clean thoroughly any areas where mud and other debris can collect.


6-22


(cid:127) (cid:127) (cid:127) (cid:127) Exhaust System Inspection Inspect the complete exhaust system. Inspect the body near the exhaust system. Look for broken, damaged, missing or out-of-position parts as well as open seams, holes, loose connections or other conditions which could cause a heat build-up in the floor pan or could let exhaust fumes into the vehicle. See Engine Exhaust on page 2-32.


Fuel System Inspection Inspect the complete fuel system for damage or leaks.


Part C: Periodic Maintenance Inspections Listed in this part are inspections and services which should be performed at least twice a year (for instance, each spring and fall). You should let your dealer’s service department do these jobs. Make sure any necessary repairs are completed at once. Proper procedures to perform these services may be found in a service manual. See Service Publications Ordering Information on page 7-11.


Steering, Suspension and Front Drive Axle Boot and Seal Inspection Inspect the front and rear suspension and steering system for damaged, loose or missing parts, signs of wear or lack of lubrication. Inspect the power steering lines and hoses for proper hook-up, binding, leaks, cracks, chafing, etc. Clean and then inspect the drive axle boot seals for damage, tears or leakage. Replace seals if necessary.


6-23


Engine Cooling System Inspection Inspect the hoses and have them replaced if they are cracked, swollen or deteriorated. Inspect all pipes, fittings and clamps; replace as needed. Clean the outside of the radiator and air conditioning condenser. To help ensure proper operation, a pressure test of the cooling system and pressure cap is recommended at least once a year.


Throttle System Inspection Inspect the throttle system for interference or binding, and for damaged or missing parts. Replace parts as needed. Replace any components that have high effort or excessive wear. Do not lubricate accelerator and cruise control cables.


Brake System Inspection Inspect the complete system. Inspect brake lines and hoses for proper hook-up, binding, leaks, cracks, chafing, etc. Inspect disc brake pads for wear and rotors for surface condition. Inspect other brake parts, including calipers, parking brake, etc. Check parking brake adjustment. You may need to have your brakes inspected more often if your driving habits or conditions result in frequent braking.


6-24


Part D: Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number or specification may be obtained from your dealer.


Usage


Fluid/Lubricant


Engine Oil


Engine Coolant


Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol. GM Goodwrench oil meets all the requirements for your vehicle. To determine the proper viscosity for your vehicle’s engine, see Engine Oil on page 5-13.


50/50 mixture of clean, drinkable water and use only DEX-COOL® Coolant. See Engine Coolant on page 5-24.


Usage


Fluid/Lubricant


Hydraulic Brake


System


Delco Supreme 11 Brake Fluid or equivalent DOT-3 brake fluid.


Windshield


Washer Solvent GM Optikleen® Washer Solvent. Chassis Lubricant (GM Part No. U.S. 12377985, in Canada 88901242) or lubricant meeting requirements of NLGI #2, Category LB or GC-LB.


Parking Brake Cable Guides


Power Steering


System


Automatic Transaxle


GM Power Steering Fluid (GM Part No. U.S. 89021184, in Canada 89021186). DEXRON®-III Automatic Transmission Fluid. Look for Approved for the H-Specification on the label.


6-25


Usage


Key Lock Cylinders


Supercharger


Hood Latch Assembly, Secondary


Latch, Pivots, Spring Anchor and Release


Pawl


Fluid/Lubricant


Usage


Fluid/Lubricant


Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474).


Supercharger Oil (GM Part No. U.S. 12345982, in Canada 10953513). See Supercharger Oil on page 5-18.


Lubriplate Lubricant Aerosol (GM Part No. U.S. 12346293, in Canada 992723) or lubricant meeting requirements of NLGI #2, Category LB or GC-LB.


Hood and


Door Hinges


Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474).


Fuel Door, Glove Box


Door, Console Door and Rear Compartment


Lid Hinges


Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474).


Weatherstrip Conditioning


Dielectric Silicone Grease (GM Part No. U.S. 12345579, in Canada 992887).


6-26


Part E: Maintenance Record After the scheduled services are performed, record the date, odometer reading and who performed the service and any additional information from “Owner Checks and Services” or “Periodic Maintenance” on the following record pages. Also, you should retain all maintenance receipts.


Maintenance Record


Date


Odometer Reading


Serviced By


Maintenance Record


6-27


Date


Odometer Reading


Serviced By


Maintenance Record


Maintenance Record (cont’d)


6-28


Section 7


Customer Assistance and Information


Customer Assistance


and Information ............................................7-2
Customer Satisfaction Procedure ......................7-2
Online Owner Center ......................................7-3
Customer Assistance for Text Telephone


(TTY) Users ...............................................7-4
Customer Assistance Offices ............................7-4
GM Mobility Program for Persons with


Disabilities ..................................................7-5
Roadside Assistance Program ..........................7-6
Courtesy Transportation ...................................7-7
Vehicle Data Collection and Event Data


Recorders ..................................................7-9


Reporting Safety Defects ................................7-10


Reporting Safety Defects to the United States


Government ..............................................7-10


Reporting Safety Defects to the Canadian

Loading...
x