2013 Buick Lacrosse Owners Manual

Link Connector (DLC).

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (18,1)

5-18

Instruments and Controls

vehicle would be considered not ready for inspection. This can happen if the 12-volt battery has recently been replaced or run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This can take several days of routine driving. If this has been done and the vehicle still does not pass the inspection for lack of OBD II system readiness, your dealer can prepare the vehicle for inspection.

Brake System Warning Light The vehicle brake system consists of two hydraulic circuits. If one circuit is not working, the remaining circuit can still work to stop the vehicle. For normal braking performance, both circuits need to be working.

If the warning light comes on, there is a brake problem. Have your brake system inspected right away.

Metric

English

With antilock brakes, this light should come on when the vehicle is placed in START. If it does not, have the vehicle serviced by your dealer. If the light comes on while driving, pull off the road and stop carefully. The pedal may be harder to push or it can go closer to the floor. It may take longer to stop. Try turning off and restarting the vehicle one or two times. If the light is still on, have the vehicle towed for service. See Antilock Brake System (ABS) Warning Light on page 5‑19 and Towing the Vehicle on page 10‑90.

The DLC is under the instrument panel next to the steering wheel. See your dealer if assistance is needed. The vehicle may not pass inspection if:

The malfunction indicator lamp is on while the vehicle is running. The vehicle is in ON/RUN for keyed access, or service only mode for keyless access and the malfunction indicator lamp does not come on. See your dealer for assistance in verifying proper operation of the malfunction indicator lamp. The OBD II (On-Board Diagnostics) system determines that critical emission control systems have not been completely diagnosed. The

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (19,1)

{ WARNING

The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service.

Electric Parking Brake Light

Metric

English

For vehicles with the Electric Parking Brake (EPB), the parking brake status light comes on when

Instruments and Controls

5-19

the parking brake is applied. If the light continues flashing after the parking brake is released, or while driving, there is a problem with the Electric Parking Brake system. A message may also display in the Driver Information Center (DIC). See Brake System Messages on page 5‑33 for more information. If the light does not come on, or remains flashing, see your dealer.

If this light comes on, there is a problem with a system on the vehicle that is causing the parking brake system to work at a reduced level. The vehicle can still be driven, but should be taken to a dealer as soon as possible. See Parking Brake on page 9‑32 for more information. For vehicles with the uplevel or eAssist cluster, this telltale displays in the Driver Information Center (DIC) screen.

Antilock Brake System (ABS) Warning Light

For vehicles with the Electric Parking Brake (EPB), the parking brake warning light should come on briefly when ignition is placed in ON/ RUN. If it does not come on, then have it fixed so it will be ready to warn if there is a problem.

This light comes on briefly when the engine is started.

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (20,1)

5-20

Instruments and Controls

If the light does not come on, have it fixed so it will be ready to warn if there is a problem. If the ABS light stays on, turn the ignition off. If the light comes on while driving, stop as soon as it is safely possible and turn off the vehicle. Then start the engine again to reset the system. If the ABS light stays on, or comes on again while driving, the vehicle needs service. A chime may also sound when the light comes on steady. If the ABS light is the only light on, the vehicle has regular brakes, but the antilock brakes are not functioning. If both the ABS and the brake system warning light are on, the vehicle's antilock brakes are not functioning and there is a problem with the regular brakes. See your dealer for service.

See Brake System Warning Light on page 5‑18 and Brake System Messages on page 5‑33.

Traction Off Light

If the light comes on and stays on for an extended period of time while the system is turned on, the vehicle needs service. See Traction Control System (TCS) on page 9‑34 and StabiliTrak® System on page 9‑35.

StabiliTrak® OFF Light

This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. This light comes on when the Traction Control System (TCS) has been turned off by pressing and releasing the TCS/StabiliTrak button. This light also comes on and the system turns off if there is a problem with the TCS.

This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. This light comes on when the StabiliTrak system is turned off. If the Traction Control System (TCS) is off, wheel spin is not limited. If StabiliTrak is off, the system does not assist in controlling the vehicle.

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (21,1)

Instruments and Controls

5-21

be limiting wheel spin and aiding in maintaining directional control of the vehicle. For vehicles with an uplevel or eAssist cluster, this light comes on in the Driver information Center (DIC). See StabiliTrak® System on page 9‑35 and Traction Control System (TCS) on page 9‑34. See Ride Control System Messages on page 5‑37 for more information on the messages associated with this light.

Turn on the TCS and the StabiliTrak system and the warning light turns off. See Traction Control System (TCS) on page 9‑34 and StabiliTrak® System on page 9‑35 for more information.

Traction Control System (TCS)/StabiliTrak® Light

The Traction Control System (TCS)/ StabiliTrak light comes on briefly when the engine is started. If the light does not come on, have the vehicle serviced by the dealer. If the system is working normally, the indicator light turns off.

If the light is on while certain DIC messages display, this indicates that the TCS and StabiliTrak systems are not working or are disabled. If the light is on and not flashing, the TCS and potentially the StabiliTrak system have been disabled. Check the DIC messages to determine which feature(s) is no longer functioning and whether it is because of the driver turning off the feature(s), or because the system is not working properly and the vehicle requires service. If the TCS is disabled, wheel spin is not limited. If the StabiliTrak system is disabled, the system does not aid in maintaining directional control of the vehicle. If the indicator/warning light is on and flashing, the TCS or the StabiliTrak system is actively working. Check the DIC messages for details to determine which system is working. If a message appears in the DIC, the system may

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (22,1)

5-22

Instruments and Controls

Engine Coolant Temperature Warning Light

For eAssist vehicles, this light comes on briefly while starting the vehicle. If it does not, have the vehicle serviced by the dealer. If the system is working normally, the indicator light goes off. Notice: Driving with the engine coolant temperature warning light on could cause the vehicle to overheat. See Engine Overheating on page 10‑21. The vehicle's engine could be damaged, and it might not be covered by the

vehicle warranty. Never drive with the engine coolant temperature warning light on. The engine coolant temperature warning light comes on when the engine has overheated. If this happens, pull over and turn off the engine as soon as possible. See Engine Overheating on page 10‑21.

Tire Pressure Light

For vehicles with the Tire Pressure Monitor System (TPMS), this light comes on briefly when the engine is started. It provides information about tire pressures and the TPMS.

When the Light Is On Steady This indicates that one or more of the tires are significantly underinflated. A Driver Information Center (DIC) tire pressure message may also display. See Tire Messages on page 5‑38. Stop as soon as possible, and inflate the tires to the pressure value shown on the Tire and Loading Information label. See Tire Pressure on page 10‑50.

When the Light Flashes First and Then Is On Steady If the light flashes for about a minute and then stays on, there may be a problem with the TPMS. If the problem is not corrected, the light will come on at every ignition cycle. See Tire Pressure Monitor Operation on page 10‑52.

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (23,1)

Instruments and Controls

5-23

If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle could be low on oil and might have some other system problem. See your dealer. For vehicles with the uplevel or eAssist cluster, this telltale displays in the Driver Information Center (DIC) screen.

Low Fuel Warning Light

This light also comes on when the fuel tank is low on fuel. When fuel is added the light should go off. If it does not, have your vehicle serviced. For vehicles with an uplevel or eAssist cluster, this telltale displays in the Driver Information Center (DIC) screen.

Security Light

low can also damage the

Engine Oil Pressure Light Notice: Lack of proper engine oil maintenance can damage the engine. Driving with the engine oil engine. The repairs would not be covered by the vehicle warranty. Check the oil level as soon as possible. Add oil if required, but if the oil level is within the operating range and the oil pressure is still low, have the vehicle serviced. Always follow the maintenance schedule for changing engine oil.

The oil pressure light should come on briefly as the engine is started. If it does not come on have the vehicle serviced by your dealer.

This light, below the fuel gauge, comes on briefly when the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light then goes off.

The immobilizer light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off. If the light stays on and the engine does not start, there could be a problem with the theft-deterrent

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (24,1)

5-24

Instruments and Controls

system. See Immobilizer Operation (Key Access) on page 2‑13 or Immobilizer Operation (Keyless Access) on page 2‑14. For vehicles with an uplevel or eAssist cluster, this light displays in the Driver Information Center (DIC) screen.

High-Beam On Light

This light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 6‑2 for more information.

Front Fog Lamp Light

The lamps on reminder light comes on when the exterior lamps are in use. See Exterior Lamp Controls on page 6‑1.

Cruise Control Light

For vehicles with fog lamps, this light comes on when the fog lamps are on. The light goes out when the fog lamps are turned off. See Fog Lamps on page 6‑4 for more information.

Lamps On Reminder

This light is white whenever the cruise control is set and turns green when the cruise control is active. The light goes out when the cruise control is turned off. See Cruise Control on page 9‑37. For vehicles with the uplevel or eAssist cluster, this telltale will be shown in the Driver Information Center (DIC) screen.

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (25,1)

Instruments and Controls

5-25

Door Ajar Light

Information Displays

This light comes on in the Driver Information Center (DIC) when a door is open or not securely latched. Before driving, check that all doors are properly closed.

Driver Information Center (DIC) The Driver Information Center (DIC) displays information about the vehicle. It also displays warning messages if a system problem is detected. See Vehicle Messages on page 5‑32 for more information. All messages appear in the DIC display located in the center of the instrument panel cluster. On some models, the DIC may show warning lights or indicators in the top portion of the display. See Warning Lights, Gauges, and Indicators on page 5‑8 for more information. The vehicle may also have features that can be customized through the controls on the radio. See Vehicle Personalization on page 5‑39 for more information.

DIC Operation and Displays The DIC has different displays which can be accessed by using the DIC buttons on the turn signal lever to the left of the steering wheel. The DIC displays trip, fuel, vehicle system information, and warning messages if a system problem is detected. The bottom of the DIC display shows what position the shift lever is in, the odometer, and the direction the vehicle is driving. In cold weather the DIC display may change slowly. This is normal and will move more quickly as the vehicle's interior temperature rises.

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (26,1)

5-26

Instruments and Controls

DIC Buttons

1. SET/CLR: Press to set or clear

the menu item when it is displayed.

2. w / x (Thumbwheel): Use to scroll through the items in each menu. A small marker will move across the bottom of the page as you scroll through the items. This shows where each page is in the menu.

3. MENU: Press to get to the Trip/

Fuel Menu and the Vehicle Information Menu.

Trip/Fuel Menu Items Press MENU on the turn signal lever until Trip/Fuel Information Menu is displayed. Use w / x to scroll through the following menu items: . Digital Speedometer

Trip 1
Trip 2

. Power Flow Gauge

(eAssist Only) Fuel Range

. Average Fuel Economy/

Instantaneous Fuel Economy

. Average Vehicle Speed

Timer

. Navigation

Digital Speedometer The speedometer shows how fast the vehicle is moving in either kilometers per hour (km/h) or miles per hour (mph). The speedometer cannot be reset.

Trip 1 and Trip 2
This display shows the current distance traveled, in either kilometers (km) or miles (mi), since the last reset for the trip odometer. The trip odometer can be reset to zero by pressing SET/CLR while the trip odometer display is showing.

Power Flow Gauge (eAssist Only) This display shows the operating mode of the eAssist system and the high voltage battery charge level. The animation indicates the direction of energy flow.

Fuel Range This display shows the approximate distance the vehicle can be driven without refueling. The fuel range estimate is based on an average of the vehicle's fuel economy over recent driving history and the amount of fuel remaining in the fuel tank. Fuel range cannot be reset.

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (27,1)

Average Fuel Economy/ Instantaneous Fuel Economy On some models, this display shows Average Fuel Economy. On other models, this display shows both Average Fuel Economy and Instantaneous Fuel Economy. The Average Fuel Economy display shows the approximate average liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number is calculated based on the number of L/100 km (mpg) recorded since the last time this menu item was reset. The fuel economy can be reset by pressing SET/CLR while the Average Fuel Economy display is showing. The Instantaneous Fuel Economy display shows the current fuel economy in liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number reflects only the fuel economy that the vehicle has right now and changes frequently as

Instruments and Controls

5-27

driving conditions change. Unlike average economy, this display cannot be reset.

Average Vehicle Speed This display shows the average speed of the vehicle in miles per hour (mph) or kilometers per hour (km/h). This average is calculated based on the various vehicle speeds recorded since the last reset of this value. The average speed can be reset by pressing SET/CLR while the Average Vehicle Speed display is showing.

Timer This display can be used as a timer. To start the timer, press SET/CLR while Timer is displayed. The display will show the amount of time that has passed since the timer was last reset, not including time the ignition is off. Time will continue to be counted as long as the ignition is on, even if another display is being shown on the DIC. The timer will record up to 99 hours, 59 minutes, and 59 seconds (99:59:59) after

which the display will return to zero. To stop the timer, press SET/CLR briefly while Timer is displayed. To reset the timer to zero, press and hold SET/CLR.

Navigation This display is used for the OnStar or Navigation System Turn-by-Turn guidance. See OnStar Overview on page 14‑1 or the navigation manual, if the vehicle has navigation, for more information. Vehicle Information Menu Items Press MENU on the turn signal lever until Vehicle Information Menu is displayed. Use w / x to scroll through the following menu items: . Unit

Tire Pressure Jump Start (eAssist Only)

. Remaining Oil Life . Battery Voltage

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (28,1)

5-28

Instruments and Controls

Unit Move w / x to switch between metric or US when the Unit display is active. Press SET/CLR to confirm the setting. This will change the displays on the cluster and DIC to either metric or English (US) measurements.

Tire Pressure The display will show a vehicle with the approximate pressures of all four tires. Tire pressure is displayed in either kilopascal (kPa) or pounds per square inch (psi). See Tire Pressure Monitor System on page 10‑51 and Tire Pressure Monitor Operation on page 10‑52 for more information.

Jump Start (eAssist Only) This display allows for on-board jump starting of the vehicle. See “Jump Starting (On-board with eAssist Only)” for more information.

Remaining Oil Life This display shows an estimate of the oil's remaining useful life. If REMAINING OIL LIFE 99% is displayed, that means 99% of the current oil life remains. When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See Engine Oil Messages on page 5‑35. The oil should be changed as soon as possible. See Engine Oil on page 10‑11. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Maintenance Schedule on page 11‑2 for more information. Remember, the Oil Life display must be reset after each oil change. It will not reset itself. Also, be careful not to reset the Oil Life display accidentally at any time other than when the oil has just been changed. It cannot be reset accurately until the next oil change. To reset the

engine oil life system, press SET/ CLR while the Oil Life display is active. See Engine Oil Life System on page 10‑13.

Battery Voltage This display, available on some vehicles, shows the current battery voltage. If the voltage is in the normal range, the value will display. For example, the display may read Battery Voltage 15.0 Volts. The vehicle's charging system regulates voltage based on the state of the battery. The battery voltage can fluctuate while viewing this information on the DIC. This is normal. See Charging System Light on page 5‑15 for more information. If there is a problem with the battery charging system, the DIC will display a message Compass The vehicle may have a compass display in the Driver Information Center (DIC). See Compass on page 5‑4 for more information.

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (29,1)

Instruments and Controls

5-29

Head-Up Display (HUD)

{ WARNING

If the HUD image is too bright or too high in your field of view, it may take you more time to see things you need to see when it is dark outside. Be sure to keep the HUD image dim and placed low in your field of view.

For vehicles with the Head-Up Display (HUD), some information concerning the operation of the vehicle is projected onto the windshield. This includes information such as the speedometer reading, rpm reading, transmission position, outside air temperature, compass heading, and a brief display of the current radio station, including XM information or CD track. It will also display turn-by-turn navigation information if the vehicle has a navigation radio.

The images are projected through the HUD lens located on the driver side of the instrument panel. Notice: If you try to use the HUD image as a parking aid, you may misjudge the distance and damage your vehicle. Do not use the HUD image as a parking aid. The HUD information can be displayed in one of three languages, English, French, or Spanish. The speedometer reading and other numerical values can be displayed in either English or metric units. The language selection is changed through the radio and the units of measurement is changed through the trip computer in the Driver Information Center (DIC). See AM-FM Radio on page 7‑9 and Driver Information Center (DIC) on page 5‑25.

HUD Display on the Vehicle

Windshield

The HUD information appears as an image focused out toward the front of the vehicle. When the ignition is placed in the ON/RUN or ON/RUN/START position, HUD will display an introductory message for a short time, until the HUD is ready.

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (30,1)

5-30

Instruments and Controls

The following indicator lights come on in the instrument panel when activated and also appear on the HUD:

Turn Signal Indicators

. High-Beam Indicator Symbol The HUD temporarily displays some vehicle warnings, such as CHECK TIRE PRESSURE and FUEL LEVEL LOW when these messages are on the DIC trip computer. The HUD also displays the following messages on vehicles with these systems, when they are active:

TRACTION CONTROL ACTIVE

. STABILITRAK ACTIVE When the HUD is on, the speedometer reading is continually displayed. The current radio station or CD track number will display for a short period of time after the radio or CD track status changes. This happens whenever radio information is changed. The speedometer size is reduced when radio, CD information, warnings,

or turn-by-turn navigation information are displayed on the HUD.

The HUD control is located to the left of the steering wheel. To adjust the HUD image so that items are properly displayed, do the following: 1. Adjust the driver seat to a

comfortable position.

2. Start the engine. 3. Adjust the HUD controls.

Use the following settings to adjust the HUD. OFF: To turn HUD off, turn the HUD dimming knob fully counterclockwise until the HUD display turns off. Brightness: Turn the dimming knob clockwise or counterclockwise to brighten or dim the display. « (Up) or ª (Down): Press the up or down arrows to center the HUD image in your view. The HUD image can only be adjusted up and down, not side to side. PAGE: Press to select the display formats. Release the PAGE button when the format number with the desired display is shown on the HUD. If vehicle messages are displayed, pressing PAGE may clear the message.

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (31,1)

Instruments and Controls

5-31

The three formats are as follows:

English Shown, Metric Similar

Format One: This display gives the speedometer reading (in English or metric units), turn signal indication, high-beam indication, transmission positions, outside air temperature, and compass heading.

English Shown, Metric Similar

Format Two: This display includes the information in Format One without the transmission information, the outside air temperature, and compass heading.

English Shown, Metric Similar

Format Three: This display includes much of the information in Format One along with a circular tachometer, but without outside air temperature and compass heading. All formats will show the turn-by-turn navigation information and provide details about the next driving maneuver to be made. When you near your next maneuver, the HUD will display a distance bar that will empty the closer you get to your maneuver. All navigation information is provided to the HUD by the navigation radio or OnStar service, for vehicles that have these features.

English Shown, Metric Similar The HUD image displayed on the windshield will automatically dim and brighten to compensate for outside lighting. However, the HUD brightness control can still be adjusted as needed. The HUD image can temporarily light up depending on the angle and position of the sunlight on the HUD display. This is normal and will change when the angle of the sunlight on the HUD display changes. Polarized sunglasses could make the HUD image harder to see.

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (32,1)

5-32

Instruments and Controls

Care of the HUD Clean the inside of the windshield as needed to remove any dirt or film that could reduce the sharpness or clarity of the HUD image. To clean the HUD lens, use a soft, clean cloth that has household glass cleaner sprayed on it. Wipe the HUD lens gently, then dry it. Do not spray cleaner directly on the lens because the cleaner could leak into the unit. If You Cannot See the HUD Image When the Ignition Is On

Is anything covering the HUD lens? Is the HUD dimmer setting bright enough? Is the HUD image adjusted to the proper height?

. Are you wearing polarized

sunglasses?

. Still no HUD image? Check the

fuse in the instrument panel fuse block. See Instrument Panel Fuse Block on page 10‑40.

If the HUD Image Is Not Clear

Is the HUD image too bright? . Are the windshield and HUD

lens clean?

If the HUD image is not correct, contact your dealer. Keep in mind that the windshield is part of the HUD system.

Vehicle Messages Messages displayed on the DIC indicate the status of the vehicle or some action that may be needed to correct a condition. Multiple messages may display one after the other. The messages that do not require immediate action can be acknowledged and cleared by pressing SET/CLR. The messages that require immediate action cannot be cleared until that action is performed. All messages should be taken seriously and clearing the messages does not correct the problem. The following are some of the vehicle messages that may be displayed depending on your vehicle content.

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (33,1)

Instruments and Controls

5-33

Battery Voltage and Charging Messages

BATTERY SAVER ACTIVE This message displays when the vehicle has detected that the battery voltage is dropping beyond a reasonable point. The battery saver system starts reducing features of the vehicle that may be noticed. At the point that features are disabled, this message displays. Turn off unnecessary accessories to allow the battery to recharge. LOW BATTERY This message is displayed when the battery voltage is low. See Battery on page 10‑27. SERVICE BATTERY CHARGING SYSTEM This message is displayed when there is a fault in the battery charging system. Take the vehicle to your dealer for service.

Brake System Messages

BRAKE FLUID LOW This message is displayed when the brake fluid level is low. See Brake Fluid on page 10‑26. STEP ON BRAKE TO RELEASE PARK BRAKE This message is displayed if you attempt to release the electric parking brake without the brake pedal applied. See Parking Brake on page 9‑32 for more information. RELEASE PARK BRAKE This message is displayed if the electric parking brake is on while the vehicle is in motion. Release it before you attempt to drive. See Parking Brake on page 9‑32 for more information. SERVICE BRAKE ASSIST This message may be displayed when there is a problem with the brake boost assist system. When this message is displayed, the brake

boost assist motor might be heard operating and you might notice pulsation in the brake pedal. This is normal under these conditions. Take the vehicle to your dealer for service. SERVICE PARKING BRAKE This message is displayed when there is a problem with the electric parking brake. See Parking Brake on page 9‑32 for more information. Take the vehicle to your dealer.

Compass Messages

CAL This message is displayed when the compass needs to be calibrated. See Compass on page 5‑4. – – Dashes will be displayed if the compass needs service. See your dealer for service.

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (34,1)

5-34

Instruments and Controls

Cruise Control Messages

CRUISE SET TO XXX This message displays when the cruise control is set and shows the speed it was set to. See Cruise Control on page 9‑37.

Door Ajar Messages

DRIVER DOOR OPEN This message will display when the driver door is open. Close the door completely. HOOD OPEN This message will display when the hood is open. Close the hood completely. LEFT REAR DOOR OPEN This message will display when the driver side rear door is open. Close the door completely.

PASSENGER DOOR OPEN This message will display when the front passenger door is open. Close the door completely. RIGHT REAR DOOR OPEN This message will display when the passenger side rear door is open. Close the door completely. TRUNK OPEN This message will display when the trunk is open. Close the trunk completely.

Engine Cooling System Messages

A/C OFF DUE TO HIGH ENGINE TEMP This message displays when the engine coolant becomes hotter than the normal operating temperature. To avoid added strain on a hot engine, the air conditioning compressor automatically turns off. When the coolant temperature

returns to normal, the air conditioning compressor turns back on. You can continue to drive the vehicle. If this message continues to appear, have the system repaired by your dealer as soon as possible to avoid damage to the engine. COOLANT LEVEL LOW ADD COOLANT This message will display if the coolant is low. See Engine Coolant on page 10‑18. ENGINE OVERHEATED — IDLE ENGINE This message displays when the engine coolant temperature is too hot. Stop and allow the vehicle to idle until it cools down. ENGINE OVERHEATED — STOP ENGINE This message displays and a continuous chime sounds if the engine cooling system reaches unsafe temperatures for operation.

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (35,1)

Instruments and Controls

5-35

Stop and turn off the vehicle as soon as it is safe to do so to avoid severe damage. This message clears when the engine has cooled to a safe operating temperature.

Engine Oil Messages

CHANGE ENGINE OIL SOON This message displays when the engine oil needs to be changed. When you change the engine oil, be sure to reset the Oil Life System. See Engine Oil Life System on page 10‑13, Driver Information Center (DIC) on page 5‑25, Engine Oil on page 10‑11, and Maintenance Schedule on page 11‑2. ENGINE OIL HOT, IDLE ENGINE This message displays when the engine oil temperature is too hot. Stop and allow the vehicle to idle until it cools down.

ENGINE OIL LOW — ADD OIL On some vehicles, this message displays when the engine oil level may be too low. Check the oil level before filling to the recommended level. If the oil is not low and this message remains on, take the vehicle to your dealer for service. See Engine Oil on page 10‑11. OIL PRESSURE LOW — STOP ENGINE This message displays if low oil pressure levels occur. Stop the vehicle as soon as safely possible and do not operate it until the cause of the low oil pressure has been corrected. Check the oil as soon as possible and have the vehicle serviced by your dealer.

Engine Power Messages

ENGINE POWER IS REDUCED This message displays when the vehicle's engine power is reduced. Reduced engine power can affect the vehicle's ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but maximum acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer for service as soon as possible.

Fuel System Messages

FUEL LEVEL LOW This message displays when the vehicle is low on fuel. Refuel as soon as possible.

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (36,1)

5-36

Instruments and Controls

TIGHTEN GAS CAP This message displays when the fuel cap is not on tight. Tighten the fuel cap.

Key and Lock Messages

NO REMOTE DETECTED This message displays when the transmitter battery is weak on vehicles with keyless access. See “Starting the Vehicle with a Low Transmitter Battery” under Remote Keyless Entry (RKE) System Operation on page 2‑3. REPLACE BATTERY IN REMOTE KEY This message displays when the battery in the Remote Keyless Entry (RKE) transmitter needs to be replaced. See “Battery Replacement” under Remote Keyless Entry (RKE) System Operation on page 2‑3.

Lamp Messages

AFL (Adaptive Forward Lighting) LAMPS NEED SERVICE This message displays when the Adaptive Forward Lighting (AFL) system is disabled and needs service. See your dealer. See Adaptive Forward Lighting (AFL) on page 6‑3 for more information.

Object Detection System Messages

PARK ASSIST OFF This message displays when the park assist system has been turned off or when there is a temporary condition causing the system to be disabled. See Ultrasonic Parking Assist on page 9‑40. SERVICE PARK ASSIST This message displays if there is a problem with the Ultrasonic Rear Parking Assist (URPA) system. Do

not use this system to help you park. See Ultrasonic Parking Assist on page 9‑40. SERVICE BLIND ZONE ALERT SYSTEM If this message appears, both SBZA displays will remain on indicating there is a problem with the SBZA system. If these displays remain on after continued driving, the system needs service. Take the vehicle to your dealer. SIDE BLIND ZONE ALERT SYSTEM OFF This message indicates that the driver has turned the system off. SIDE BLIND ZONE SYS. UNAVAILABLE This message indicates that the SBZA system is disabled because the sensor is blocked and cannot detect vehicles in the blind zone. The sensor may be blocked by mud, dirt, snow, ice, or slush. This message may also activate during

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (37,1)

Instruments and Controls

5-37

heavy rain or due to road spray. The vehicle does not need service. For cleaning, see Exterior Care on page 10‑92.

Ride Control System Messages

ALL WHEEL DRIVE OFF This message displays when the All-Wheel Drive (AWD) System has been turned off. See All-Wheel Drive on page 9‑30. SERVICE ALL WHEEL DRIVE SYSTEM This message displays when there is a problem with the All-Wheel Drive (AWD) System. See your dealer for service. SERVICE REAR AXLE This message displays when there is a problem with the All-Wheel Drive (AWD) System. See your dealer for service.

SERVICE TRACTION CONTROL This message displays when there is a problem with the Traction Control System (TCS). When this message is displayed, the system will not limit wheel spin. Adjust your driving accordingly. See your dealer for service. SERVICE STABILITRAK This message displays if there is a problem with the StabiliTrak system. If this message appears, try to reset the system. Stop; turn off the engine for at least 15 seconds; then start the engine again. If this message still comes on, it means there is a problem. See your dealer for service. The vehicle is safe to drive, however, you do not have the benefit of StabiliTrak, so reduce your speed and drive accordingly.

SPORT MODE ON This message displays when using the selective ride control. See Selective Ride Control on page 9‑37
for more information. TRACTION CONTROL OFF This message displays when the Traction Control System (TCS) is turned off. Adjust your driving accordingly.

Security Messages

THEFT ATTEMPTED This message displays if the vehicle detects a tamper condition.

Starting the Vehicle Messages

JUMP START ACTIVE WAIT TO START This message displays while performing an on-board jump start of the vehicle. See “Jump Starting (On-board with eAssist Only).”

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (38,1)

5-38

Instruments and Controls

JUMP START COMPLETE ATTEMPT START This message displays while performing an on-board jump start of the vehicle. See “Jump Starting (On-board with eAssist Only).” JUMP START DISABLED SEE OWNERS MANUAL This message displays if there is a problem with the on-board jump start system, or the 12 volt battery is too low to perform an on-board jump start. Try using jumper cables and performing a normal jump start. Take the vehicle to your dealer for service to if this message continues to be displayed.

Tire Messages

TIRE PRESSURE LOW ADD AIR TO TIRE On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the pressure in one or more of the vehicle's tires is low. The low tire pressure warning light will also come on. See Tire Pressure Light on page 5‑22. If a tire pressure message appears on the DIC, stop as soon as you can. Inflate the tires by adding air until the tire pressure is equal to the values shown on the Tire and Loading Information label. See Tires on page 10‑42, Vehicle Load Limits on page 9‑10, and Tire Pressure on page 10‑50. You can receive more than one tire pressure message at a time. To read the other messages that may have been sent at the same time, press the SET/CLR button. The DIC

also shows the tire pressure values. See Driver Information Center (DIC) on page 5‑25. SERVICE TIRE MONITOR SYSTEM This message displays if there is a problem with the Tire Pressure Monitor System (TPMS). See Tire Pressure Monitor Operation on page 10‑52. TIRE LEARNING ACTIVE This message displays when the system is learning new tires. See Tire Pressure Monitor Operation on page 10‑52.

Transmission Messages

SERVICE TRANSMISSION This message displays if there is a problem with the transmission. See your dealer.

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (39,1)

Instruments and Controls

5-39

Window Messages

OPEN, THEN CLOSE DRIVER/ PASSENGER WINDOW This message is displayed when the window needs to be reprogrammed. If the vehicle's battery has been recharged or disconnected, you will need to reprogram each front window for the express-up feature to work. See Power Windows on page 2‑17.

SHIFT TO PARK This message displays when the transmission needs to be shifted to P (Park). This may appear when attempting to remove the key from the ignition or from the vehicle if the vehicle is not in P (Park). TRANSMISSION HOT — IDLE ENGINE This message displays and a chime sounds if the transmission fluid in the vehicle gets hot. Driving with the transmission fluid temperature high can cause damage to the vehicle. Stop the vehicle and let it idle to allow the transmission to cool. This message clears when the fluid temperature reaches a safe level.

Vehicle Personalization The audio system controls are used to access the personalization menus for customizing vehicle features. CONFIG (Configuration): Press to access the Configuration Settings menu. Multifunction Knob: Turn to scroll through the menus. SELECT: Press to enter the menus and select menu items. / BACK: Press to exit or move backward in a menu.

Entering the Personalization Menus 1. Press CONFIG to access the Configuration Settings menu. 2. Turn the Multifunction knob to

highlight Vehicle Settings.

3. Press SELECT to select the

Vehicle Settings menu.

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (40,1)

5-40

Instruments and Controls

The following list of menu items may be available: . Climate and Air Quality . Comfort and Convenience . Collision/Detection Systems

Language Lighting

. Power Door Locks . Remote Lock/Unlock/Start . Return to Factory Settings Turn the Multifunction knob to highlight the menu. Press SELECT to select it. Each of the menus is detailed in the following information. Climate and Air Quality Select the Climate and Air Quality menu and the following may be displayed: . Auto Fan Speed . Air Quality Sensor . Auto Heated Seats . Air Conditioning Mode

. Remote Start Auto Heated Seats . Remote Start Cooled Seats . Auto Defog . Auto Rear Defog

Auto Fan Speed This will allow you to select the automatic fan speed. It can be adjusted to run lower or higher than normal. Press SELECT when Auto Fan Speed is highlighted to open the menu. Turn the Multifunction knob to highlight High, Medium, or Low. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Air Quality Sensor This will allow you to select whether the system will operate at high or low sensitivity. Only vehicles with the dual zone climate control will have this option.

Press SELECT when Air Quality Sensor is highlighted to open the menu. Turn the Multifunction knob to highlight High or Low. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Auto Heated Seats If equipped and turned on, this feature will automatically activate heated seats at the level required by the interior temperature. The auto heated seats can be turned off by using the heated seat buttons on the climate control panel. Press SELECT when Auto Heated Seats is highlighted to open the menu. Turn the Multifunction knob to highlight On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Air Conditioning Mode This allows selection of automatic start of the air conditioning upon vehicle start. Selecting On indicates

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (41,1)

Instruments and Controls

5-41

the air conditioning will be on when the vehicle is started. Selecting Off turns the air conditioning off each time the vehicle is started. Last Setting will resume the last setting when the vehicle was shut off. Press SELECT when Air Conditioning Mode is highlighted to open the menu. Turn the Multifunction knob to highlight Off, On, or Last Setting. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Remote Start Auto Heated Seats If equipped and turned on, this feature will turn the heated seats on when using remote start on cold days. Press SELECT when Remote Start Auto Heated Seats is highlighted. Turn the Multifunction knob to select On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Remote Start Cooled Seats If equipped and turned on, this feature will turn the cooled seats on when using remote start on warm days. Press SELECT when Remote Start Cooled Seats is highlighted. Turn the Multifunction knob to select On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Auto Defog This will allow you to turn the auto defog on or off. Only vehicles with the dual zone climate control will have this option. Press SELECT when Auto Defog is highlighted to open the menu. Turn the Multifunction knob to highlight On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Auto Rear Defog If equipped, this will allow you to turn the auto rear defog on or off. This feature will automatically turn on the rear defogger when it is cold outside. Press SELECT when Auto Rear Defog is highlighted to open the menu. Turn the Multifunction knob to highlight On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu. Comfort and Convenience Select the Comfort and Convenience menu and the following will be displayed: . Chime Volume . Driver Seat Easy Exit . Park Tilt Mirrors

Chime Volume This allows selection of the chime volume level.

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (42,1)

5-42

Instruments and Controls

Press SELECT when Chime Volume is highlighted. Turn the Multifunction knob to select Normal or High. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Driver Seat Easy Exit When on, this feature will move the driver seat rearward upon turning the ignition off and opening the driver door. This may be performed to make it easier to exit the vehicle. See “Easy Exit Driver Seat” under Memory Seats on page 3‑6. This allows you to turn the easy exit seat feature on or off. Press SELECT when Driver Seat Easy Exit is highlighted. Turn the Multifunction knob to select On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Park Tilt Mirrors When on, both the driver and passenger mirrors will tilt downward when the vehicle is shifted to R (Reverse) to improve visibility of the ground near the rear wheels. They will return to their previous driving position when the vehicle is shifted out of R (Reverse), the ignition is turned to OFF, or the vehicle is left in R (Reverse). See Park Tilt Mirrors on page 2‑16. This allows you to turn the park tilt mirrors feature on or off. Press SELECT when Park Tilt Mirrors is highlighted. Turn the Multifunction knob to select Driver & Passenger or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu. Collision/Detection Systems Select the Collision/Detection Systems menu and the following will be displayed: . Side Blind Zone Alert System

Side Blind Zone Alert System If equipped, this feature allows the Side Blind Zone Alert System feature to be turned on or off. Press SELECT when Side Blind Zone Alert System is highlighted. Turn the Multifunction knob to select On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu. Language Select the Language menu and the following will be displayed: . English French . Spanish Turn the Multifunction knob to select the language. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (43,1)

Instruments and Controls

5-43

Lighting Select the Lighting menu and the following will be displayed: . Exit Lighting . Vehicle Locator Lights

Exit Lighting This allows selection of how long the exterior lamps stay on when leaving the vehicle and it is dark outside. Press SELECT when Exit Lighting is highlighted. Turn the Multifunction knob to select Off, 30 Seconds, 1 Minute, or 2 Minutes. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Vehicle Locator Lights This allows the vehicle locator lights to be turned on or off. The vehicle locator lights come on when unlocking the vehicle with the RKE transmitter.

Press SELECT when Vehicle Locator Lights is highlighted. Turn the Multifunction knob to select On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu. Power Door Locks Select Power Door Locks and the following will be displayed: . Unlocked Door Anti Lock Out . Delayed Door Lock . Auto Door Unlock

Unlocked Door Anti Lock Out When on, this feature will keep the driver door from locking when the door is open. If Off is selected, the Unlocked Door Anti Lock Out menu will be available and the door will lock as programmed through this menu. Press SELECT when Unlocked Door Anti Lock Out is highlighted. Turn the Multifunction knob to select

On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Delayed Door Lock When on, this feature will delay the locking of the doors until five seconds after the last door is closed. You will hear three chimes to signal delayed locking is in use. Pressing either the power lock button or Q on the RKE transmitter twice will override the delayed locking feature and immediately lock all of the doors. Press SELECT when Delayed Door Lock is highlighted. Turn the Multifunction knob to select On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Auto Door Unlock This allows selection of which of the doors will automatically unlock when the vehicle is shifted into P (Park).

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (44,1)

5-44

Instruments and Controls

Press SELECT when Auto Door Unlock is highlighted. Turn the Multifunction knob to select All Doors, Driver Door, or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu. Remote Lock/Unlock/Start Select Remote Lock/Unlock/Start and the following will be displayed: . Unlock Feedback (Lights)

Locking Feedback

. Door Unlock Options . Remote Recall . Passive Entry . Remote Left In Vehicle

Unlock Feedback (Lights) When on, the exterior lamps will flash when unlocking the vehicle with the RKE transmitter. Press SELECT when Unlock Feedback (Lights) is highlighted. Turn the Multifunction knob to select

On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Locking Feedback This allows selection of what type of feedback is given when locking the vehicle with the RKE transmitter. Press SELECT when Locking Feedback is highlighted. Turn the Multifunction knob to select Lights and Horn, Lights Only, Horn Only, or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Door Unlock Options This allows selection of which doors will unlock when pressing K on the RKE transmitter. Press SELECT when Door Unlock Options is highlighted. Turn the Multifunction knob to select All Doors or Driver Door Only. When set to Driver Door Only, the driver door will unlock the first time the unlock button is pressed and all

doors will unlock when the button is pressed a second time. When set to All Doors, all of the doors will unlock at the first press of K. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Remote Recall When on, this feature will recall the current driver's last seat and outside mirror positions upon unlocking the driver door with the RKE, and opening that door. The current driver is identified when the RKE is used to unlock the driver door. If keyless access equipped, the recall will occur upon opening the driver door. See “Memory Remote Recall” under Memory Seats on page 3‑6. This allows the Remote Recall feature to be turned on or off. Remote Recall is when the memorized settings will be recalled as you unlock and enter the vehicle.

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (45,1)

Press SELECT when Remote Recall is highlighted. Turn the Multifunction knob to select On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Passive Entry This allows the Passive Entry feature to be turned on or off. Press SELECT when Passive Entry is highlighted. Turn the Multifunction knob to select On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Remote Left In Vehicle This allows the Remote Left In Vehicle reminder feature to be turned on or off. If on, the horn will chirp if a remote is left in the vehicle. Press SELECT when Remote Left In Vehicle is highlighted. Turn the Multifunction knob to select On or

Instruments and Controls

5-45

Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu. Return to Factory Settings Select Return to Factory Settings to return all of the vehicle personalization to the default settings. Turn the Multifunction knob to select Yes or No. Press SELECT to confirm and go back to the last menu.

Universal Remote System See Radio Frequency Statement on page 13‑20 for information regarding Part 15 of the Federal Communications Commission (FCC) rules and Industry Canada Standards RSS-GEN/210/220/310.

Universal Remote System Programming

If the vehicle has this feature, you will see these buttons with one indicator light next to them in the overhead console. This system provides a way to replace up to three remote control transmitters used to activate

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (46,1)

5-46

Instruments and Controls

devices such as garage door openers, security systems, and home automation devices. Do not use the Universal Remote system with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1,1982. Read the instructions completely before attempting to program the Universal Remote system. Because of the steps involved, it may be helpful to have another person available to assist with programming the Universal Remote system. Keep the original hand-held transmitter for use in other vehicles as well as for future Universal Remote system programming. It is also recommended that upon the sale of the vehicle, the programmed Universal Remote system buttons be erased for security purposes. See “Erasing Universal Remote System Buttons” later in this section.

When programming a garage door, park outside of the garage. Park directly in line with and facing the garage door opener motor-head or gate motor-head. Be sure that people and objects are clear of the garage door or gate being programmed. It is recommended that a new battery be installed in the hand-held transmitter for quicker and more accurate transmission of the radio-frequency signal. Programming the Universal Remote System For questions or help programming the Universal Remote system, call 1-800-355-3515 or go to www.homelink.com. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before starting. Otherwise, the device will time out and the procedure will have to be repeated.

To program up to three devices: 1. Hold the end of the hand-held

transmitter about 3 to 8 cm (1 to 3 in) away from the Universal Remote system buttons while keeping the indicator light in view. The hand-held transmitter was supplied by the manufacturer of the garage door opener receiver (motor-head unit).

2. At the same time, press and

hold both the hand-held transmitter button and one of the three Universal Remote system buttons to be used to operate the garage door. Do not release the Universal Remote system button or the hand-held transmitter button until the indicator light changes from a slowly to a rapidly flashing light. You now may release both buttons. Some entry gates and garage door openers may require substitution of Step 2 with the

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (47,1)

procedure noted in “Gate Operator and Canadian Programming” later in this section.

3. Press and hold for five seconds

the newly trained Universal Remote system button (the button selected in Step 2) while observing the indicator light and garage door activation.

If the indicator light stays on continuously or the garage door starts to move when the Universal Remote system button is pressed and released, then the programming is complete. There is no need to continue programming Steps 4–6.

Instruments and Controls

5-47

If the Universal Remote system indicator light blinks rapidly for two seconds, then turns to a constant light and the garage door does not move, continue with programming Steps 4–6. It may be helpful to have another person assist with the remaining Steps 4–6.

“Learn” or “Smart” Button

4. After Steps 1–3 have been

completed, locate the “Learn” or “Smart” button inside the garage on the garage door opener receiver (motor-head unit). The name and color of the button may vary by manufacturer.

5. Firmly press and release the

6.

“Learn” or “Smart” button. After pressing this button, you will have 30 seconds to complete Step 6. Immediately return to the vehicle. Firmly press and hold for two seconds the Universal Remote system button, selected in Step 2 to control the garage door, and then release it. If the garage door does not move or the lamp on the garage door opener receiver (motor-head unit) does not flash, press and hold the same button a second time for two seconds, then release it. Again, if the door does not move or the garage door lamp does not flash, press and hold the same button a third time for two seconds, then release.

The Universal Remote system should now activate the garage door.

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (48,1)

5-48

Instruments and Controls

To program the remaining two Universal Remote system buttons, begin with Step 1 of “Programming the Universal Remote System.” Gate Operator and Canadian Programming If you have questions or need help programming the Universal Remote system, call 1-800-355-3515 or go to www.homelink.com. Canadian radio-frequency laws require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for the Universal Remote system to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to time out in the same manner.

If you live in Canada, or you are having difficulty programming a gate operator or garage door opener by using the “Programming the Universal Remote System” procedures, regardless of where you live, replace Step 2 under “Programming the Universal Remote System” with the following: Continue to press and hold the Universal Remote system button while you press and release every two seconds (cycle) the hand-held transmitter button until the frequency signal has been successfully accepted by the Universal Remote system. The Universal Remote system indicator light will flash slowly at first and then rapidly. Proceed with Step 3 under “Programming the Universal Remote System” to complete.

Universal Remote System Operation

Using the Universal Remote System Press and hold the appropriate Universal Remote system button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing Universal Remote System Buttons All programmed buttons should be erased when the vehicle is sold or the lease ends. To erase all programmed buttons on the Universal Remote system device: 1. Press and hold down the two

outside buttons until the indicator light begins to flash. This should take about 10 seconds.

2. Release both buttons.

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (49,1)

Instruments and Controls

5-49

Reprogramming a Single Universal Remote System Button To reprogram any of the three Universal Remote system buttons: 1. Press and hold the desired

Universal Remote system button. Do not release the button.

2. The indicator light will begin to flash after 20 seconds. Without releasing the button, proceed with Step 1 under “Programming the Universal Remote System.” If you have questions or need help programming the Universal Remote system, call 1-800-355-3515 or go to www.homelink.com. You may also call the customer assistance phone number under Customer Assistance Offices (U.S. and Canada) on page 13‑4 or Customer Assistance Offices (Mexico) on page 13‑5.

Buick LaCrosse Owner Manual - 2013 - 1st crc - 4/10/12

Black plate (50,1)

5-50

Instruments and Controls

2 NOTES