2012 Buick Lacrosse Owners Manual

read the other messages that may have been sent at the same time, press the SET/CLR button.

The DIC also shows the tire pressure values. See Driver Information Center (DIC) on page 5‑25. SERVICE TIRE MONITOR SYSTEM This message displays if there is a problem with the Tire Pressure Monitor System (TPMS). See Tire Pressure Monitor Operation on page 10‑54 for more information. TIRE LEARNING ACTIVE This message displays when the system is learning new tires. See Tire Pressure Monitor Operation on page 10‑54 for more information.

Transmission Messages

SERVICE TRANSMISSION This message displays if there is a problem with the transmission. See your dealer.

SHIFT TO PARK This message displays when the transmission needs to be shifted to P (Park). This may appear when attempting to remove the key from the ignition or from the vehicle if the vehicle is not in P (Park). TRANSMISSION HOT — IDLE ENGINE This message displays and a chime sounds if the transmission fluid in the vehicle gets hot. Driving with the transmission fluid temperature high can cause damage to the vehicle. Stop the vehicle and let it idle to allow the transmission to cool. This message clears when the fluid temperature reaches a safe level.

Buick LaCrosse Owner Manual - 2012

Black plate (40,1)

5-40

Instruments and Controls

Window Messages

OPEN, THEN CLOSE DRIVER WINDOW This message is displayed when the window needs to be reprogrammed. If the vehicle's battery has been recharged or disconnected, you will need to reprogram each front window for the express-up feature to work. See Power Windows on page 2‑19 for more information. OPEN, THEN CLOSE PASSENGER WINDOW This message is displayed when the window needs to be reprogrammed. If the vehicle's battery has been recharged or disconnected, you will need to reprogram each front window for the express-up feature to work. See Power Windows on page 2‑19 for more information.

Vehicle Personalization The audio system controls are used to access the personalization menus for customizing vehicle features. CONFIG (Configuration): Press to access the Configuration Settings menu. Menu Knob: Turn to scroll through the menus. SELECT: Press to enter the menus and select menu items. / BACK: Press to exit or move backward in a menu.

Entering the Personalization Menus 1. Press CONFIG to access the Configuration Settings menu.

2. Turn the Menu knob to highlight

Vehicle Settings.

3. Press SELECT to select the

Vehicle Settings menu.

The following list of menu items may be available: . Climate and Air Quality . Comfort and Convenience . Collision/Detection Systems

Language Lighting

. Power Door Locks . Remote Lock/Unlock/Start . Return to Factory Settings Turn the Menu knob to highlight the menu. Press SELECT to select it. Each of the menus is detailed in the following information. Climate and Air Quality Select the Climate and Air Quality menu and the following may be displayed: . Auto Fan Speed . Air Quality Sensor . Auto Heated Seats . Air Conditioning Mode

Buick LaCrosse Owner Manual - 2012

Black plate (41,1)

. Remote Start Auto Heated Seats . Remote Start Cooled Seats . Auto Defog . Auto Rear Defog

Auto Fan Speed This will allow you to select the automatic fan speed. It can be adjusted to run lower or higher than normal. Press SELECT when Auto Fan Speed is highlighted to open the menu. Turn the Menu knob to highlight High, Medium, or Low. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Air Quality Sensor This will allow you to select whether the system will operate at high or low sensitivity. Only vehicles with the dual zone climate control will have this option.

Instruments and Controls

5-41

Press SELECT when Air Quality Sensor is highlighted to open the menu. Turn the Menu knob to highlight High or Low. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Auto Heated Seats If equipped and turned on, this feature will automatically activate heated seats at the level required by the interior temperature. The auto heated seats can be turned off by using the heated seat buttons on the climate control panel. Press SELECT when Auto Heated Seats is highlighted to open the menu. Turn the Menu knob to highlight On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Air Conditioning Mode This allows selection of automatic start of the air conditioning upon vehicle start. Selecting On indicates the air conditioning will be on when

the vehicle is started. Selecting Off turns the air conditioning off each time the vehicle is started. Last Setting will resume the last setting when the vehicle was shut off. Press SELECT when Air Conditioning Mode is highlighted to open the menu. Turn the Menu knob to highlight Off, On, or Last Setting. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Remote Start Auto Heated Seats If equipped and turned on, this feature will turn the heated seats on when using remote start on cold days. Press SELECT when Remote Start Auto Heated Seats is highlighted. Turn the Menu knob to select On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Buick LaCrosse Owner Manual - 2012

Black plate (42,1)

5-42

Instruments and Controls

Remote Start Cooled Seats If equipped and turned on, this feature will turn the cooled seats on when using remote start on warm days. Press SELECT when Remote Start Cooled Seats is highlighted. Turn the Menu knob to select On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Auto Defog This will allow you to turn the auto defog on or off. Only vehicles with the dual zone climate control will have this option. Press SELECT when Auto Defog is highlighted to open the menu. Turn the Menu knob to highlight On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Auto Rear Defog If equipped, this will allow you to turn the auto rear defog on or off. This feature will automatically turn on the rear defogger when it is cold outside. Press SELECT when Auto Rear Defog is highlighted to open the menu. Turn the Menu knob to highlight On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu. Comfort and Convenience Select the Comfort and Convenience menu and the following will be displayed: . Chime Volume . Driver Seat Easy Exit . Park Tilt Mirrors

Chime Volume This allows selection of the chime volume level.

Press SELECT when Chime Volume is highlighted. Turn the Menu knob to select Normal or High. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Driver Seat Easy Exit When on, this feature will move the driver seat rearward upon turning the ignition off and opening the driver door. This may be performed to make it easier to exit the vehicle. See “Easy Exit Driver Seat” under Power Seat Adjustment on page 3‑5
for more information. This allows you to turn the easy exit seat feature on or off. Press SELECT when Driver Seat Easy Exit is highlighted. Turn the Menu knob to select On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Buick LaCrosse Owner Manual - 2012

Black plate (43,1)

Park Tilt Mirrors When on, both the driver and passenger mirrors will tilt downward when the vehicle is shifted to R (Reverse) to improve visibility of the ground near the rear wheels. They will return to their previous driving position when the vehicle is shifted out of R (Reverse), the ignition is turned to OFF, or the vehicle is left in R (Reverse). See Park Tilt Mirrors on page 2‑17 for more information. This allows you to turn the park tilt mirrors feature on or off. Press SELECT when Park Tilt Mirrors is highlighted. Turn the Menu knob to select Driver & Passenger or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Instruments and Controls

5-43

Collision/Detection Systems Select the Collision/Detection Systems menu and the following will be displayed: . Side Blind Zone Alert System

Side Blind Zone Alert System If equipped, this feature allows the Side Blind Zone Alert System feature to be turned on or off. Press SELECT when Side Blind Zone Alert System is highlighted. Turn the Menu knob to select On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu. Language Select the Language menu and the following will be displayed: . English French . Spanish

Turn the Menu knob to select the language. Press SELECT to confirm the selection. Press / BACK to move to the last menu. Lighting Select the Lighting menu and the following will be displayed: . Exit Lighting . Vehicle Locator Lights

Exit Lighting This allows selection of how long the exterior lamps stay on when leaving the vehicle and it is dark outside. Press SELECT when Exit Lighting is highlighted. Turn the Menu knob to select Off, 30 Seconds, 1 Minute, or 2 Minutes. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Buick LaCrosse Owner Manual - 2012

Black plate (44,1)

5-44

Instruments and Controls

Vehicle Locator Lights This allows the vehicle locator lights to be turned on or off. The vehicle locator lights come on when unlocking the vehicle with the RKE transmitter. Press SELECT when Vehicle Locator Lights is highlighted. Turn the Menu knob to select On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu. Power Door Locks Select Power Door Locks and the following will be displayed: . Unlocked Door Anti Lock Out . Delayed Door Lock . Auto Door Unlock

Unlocked Door Anti Lock Out When on, this feature will keep the driver door from locking when the door is open. If off is selected, the Unlocked Door Anti Lock Out menu

will be available and the door will lock as programmed through this menu. Press SELECT when Unlocked Door Anti Lock Out is highlighted. Turn the Menu knob to select On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Delayed Door Lock When on, this feature will delay the locking of the doors until five seconds after the last door is closed. You will hear three chimes to signal delayed locking is in use. Pressing either the power lock button or Q on the RKE transmitter twice will override the delayed locking feature and immediately lock all of the doors. Press SELECT when Delayed Door Lock is highlighted. Turn the Menu knob to select On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Auto Door Unlock This allows selection of which of the doors will automatically unlock when the vehicle is shifted into P (Park). Press SELECT when Auto Door Unlock is highlighted. Turn the Menu knob to select All Doors, Driver Door, or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu. Remote Lock/Unlock/Start Select Remote Lock/Unlock/Start and the following will be displayed: . Unlock Feedback (Lights)

Locking Feedback

. Door Unlock Options . Remote Recall . Passive Entry . Remote Left In Vehicle

Buick LaCrosse Owner Manual - 2012

Black plate (45,1)

Unlock Feedback (Lights) When on, the exterior lamps will flash when unlocking the vehicle with the RKE transmitter. Press SELECT when Unlock Feedback (Lights) is highlighted. Turn the Menu knob to select On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Locking Feedback This allows selection of what type of feedback is given when locking the vehicle with the RKE transmitter. Press SELECT when Locking Feedback is highlighted. Turn the Menu knob to select Lights and Horn, Lights Only, Horn Only, or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Instruments and Controls

5-45

Door Unlock Options This allows selection of which doors will unlock when pressing K on the RKE transmitter. Press SELECT when Door Unlock Options is highlighted. Turn the Menu knob to select All Doors or Driver Door Only. When set to Driver Door Only, the driver door will unlock the first time the unlock button is pressed and all doors will unlock when the button is pressed a second time. When set to All Doors, all of the doors will unlock at the first press of K. Press SELECT to confirm the selection. Press / BACK to move to the last menu. Remote Recall When on, this feature will recall the current driver's last seat and outside mirror positions upon unlocking the driver door with the RKE, and opening that door. The current driver is identified when the RKE is used to unlock the driver door. If keyless access equipped, the recall will

occur upon opening the driver door. See “Memory Remote Recall” under Power Seat Adjustment on page 3‑5
for more information. This allows the Remote Recall feature to be turned on or off. Remote Recall is when the memorized settings will be recalled as you unlock and enter the vehicle. Press SELECT when Remote Recall is highlighted. Turn the Menu knob to select On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Passive Entry This allows the Passive Entry feature to be turned on or off. Press SELECT when Passive Entry is highlighted. Turn the Menu knob to select On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu.

Buick LaCrosse Owner Manual - 2012

Black plate (46,1)

5-46

Instruments and Controls

Remote Left In Vehicle This allows the Remote Left In Vehicle reminder feature to be turned on or off. If on, the horn will chirp if a remote is left in the vehicle. Press SELECT when Remote Left In Vehicle is highlighted. Turn the Menu knob to select On or Off. Press SELECT to confirm the selection. Press / BACK to move to the last menu. Return to Factory Settings Select Return to Factory Settings to return all of the vehicle personalization to the default settings. Turn the Menu knob to select Yes or No. Press SELECT to confirm and go back to the last menu.

Universal Remote System See Radio Frequency Statement on page 13‑20 for information regarding Part 15 of the Federal Communications Commission (FCC) rules and Industry Canada Standards RSS-GEN/210/220/310.

Universal Remote System Programming

If the vehicle has this feature, you will see these buttons with one LED indicator next to them in the overhead console. This system provides a way to replace up to three remote control transmitters used to activate

devices such as garage door openers, security systems, and home automation devices. Do not use the Universal Remote system with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1,1982. Read the instructions completely before attempting to program the Universal Remote system. Because of the steps involved, it may be helpful to have another person available to assist with programming the Universal Remote system. Keep the original hand-held transmitter for use in other vehicles as well as for future Universal Remote system programming. It is also recommended that upon the sale of the vehicle, the programmed Universal Remote system buttons be erased for security purposes. See “Erasing Universal Remote System Buttons” later in this section.

Buick LaCrosse Owner Manual - 2012

Black plate (47,1)

When programming a garage door, park outside of the garage. Park directly in line with and facing the garage door opener motor-head or gate motor-head. Be sure that people and objects are clear of the garage door or gate being programmed. It is recommended that a new battery be installed in the hand-held transmitter for quicker and more accurate transmission of the radio-frequency signal. Programming the Universal Remote System For questions or help programming the Universal Remote system, call 1‐800‐355‐3515 or go to www.homelink.com. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before starting. Otherwise, the device will time out and the procedure will have to be repeated.

Instruments and Controls

5-47

To program up to three devices: 1. Hold the end of the hand-held

transmitter about 3 to 8 cm (1 to 3 in) away from the Universal Remote system buttons while keeping the indicator light in view. The hand-held transmitter was supplied by the manufacturer of the garage door opener receiver (motor-head unit).

2. At the same time, press and

hold both the hand-held transmitter button and one of the three Universal Remote system buttons to be used to operate the garage door. Do not release the Universal Remote system button or the hand-held transmitter button until the indicator light changes from a slowly to a rapidly flashing light. You now may release both buttons.

Some entry gates and garage door openers may require substitution of Step 2 with the procedure noted in “Gate Operator and Canadian Programming” later in this section.

3. Press and hold for five seconds

the newly trained Universal Remote system button (the button selected in Step 2) while observing the indicator light and garage door activation.

If the indicator light stays on continuously or the garage door starts to move when the Universal Remote system button is pressed and released, then the programming is complete. There is no need to continue programming Steps 4 through 6.

Buick LaCrosse Owner Manual - 2012

Black plate (48,1)

5-48

Instruments and Controls

If the Universal Remote system indicator light blinks rapidly for two seconds, then turns to a constant light and the garage door does not move, continue with programming Steps 4
through 6. It may be helpful to have another person assist with the remaining Steps 4
through 6.

“Learn” or “Smart” Button 4. After Steps 1 through 3 have

been completed, locate the “Learn” or “Smart” button inside the garage on the garage door opener receiver (motor-head

unit). The name and color of the button may vary by manufacturer.

5. Firmly press and release the

6.

“Learn” or “Smart” button. After pressing this button, you will have 30 seconds to complete Step 6. Immediately return to the vehicle. Firmly press and hold for two seconds the Universal Remote system button, selected in Step 2 to control the garage door, and then release it. If the garage door does not move or the lamp on the garage door opener receiver (motor-head unit) does not flash, press and hold the same button a second time for two seconds, and then release it. Again, if the door does not move or the garage door lamp does not flash, press and hold the same button a third time for two seconds, and then release.

The Universal Remote system should now activate the garage door. To program the remaining two Universal Remote system buttons, begin with Step 1 of “Programming the Universal Remote System.” Gate Operator and Canadian Programming If you have questions or need help programming the Universal Remote system, call 1‐800‐355‐3515 or go to www.homelink.com. Canadian radio-frequency laws require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for the Universal Remote system to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to time out in the same manner.

Buick LaCrosse Owner Manual - 2012

Black plate (49,1)

If you live in Canada, or you are having difficulty programming a gate operator or garage door opener by using the “Programming the Universal Remote System” procedures, regardless of where you live, replace Step 2 under “Programming the Universal Remote System” with the following: Continue to press and hold the Universal Remote system button while you press and release every two seconds (cycle) the hand-held transmitter button until the frequency signal has been successfully accepted by the Universal Remote system. The Universal Remote system indicator light will flash slowly at first and then rapidly. Proceed with Step 3 under “Programming the Universal Remote System” to complete.

Instruments and Controls

5-49

Universal Remote System Operation

Using the Universal Remote System Press and hold the appropriate Universal Remote system button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing Universal Remote System Buttons All programmed buttons should be erased when the vehicle is sold or the lease ends. To erase all programmed buttons on the Universal Remote system device: 1. Press and hold down the two

outside buttons until the indicator light begins to flash. This should take about 10 seconds.

2. Release both buttons.

Reprogramming a Single Universal Remote System Button To reprogram any of the three Universal Remote system buttons: 1. Press and hold the desired

Universal Remote system button. Do not release the button.

2. The indicator light will begin to flash after 20 seconds. Without releasing the button, proceed with Step 1 of the section “Programming the Universal Remote System.”

If you have questions or need help programming the Universal Remote system, call 1‐800‐355‐3515 or go to www.homelink.com. You may also call the customer assistance phone number under Customer Assistance Offices (U.S. and Canada) on page 13‑4 or Customer Assistance Offices (Mexico) on page 13‑5.

Buick LaCrosse Owner Manual - 2012

Black plate (50,1)

5-50

Instruments and Controls

2 NOTES

Buick LaCrosse Owner Manual - 2012

Black plate (1,1)

Lighting

6-1

Interior Lighting

Instrument Panel Illumination

Control . . . . . . . . . . . . . . . . . . . . . . 6-6
Dome Lamps . . . . . . . . . . . . . . . . . 6-6
Reading Lamps . . . . . . . . . . . . . . . 6-6
Sun Visor Lamps . . . . . . . . . . . . . . 6-7

Lighting Features

Entry Lighting . . . . . . . . . . . . . . . . . 6-7
Exit Lighting . . . . . . . . . . . . . . . . . . . 6-7
Battery Load Management . . . . 6-8
Battery Power Protection . . . . . . 6-8

Lighting

Exterior Lighting

Exterior Lamp Controls . . . . . . . . 6-2
Exterior Lamps Off

Reminder . . . . . . . . . . . . . . . . . . . . 6-2

Headlamp High/Low-Beam

Changer . . . . . . . . . . . . . . . . . . . . . 6-2
Flash-to-Pass . . . . . . . . . . . . . . . . . 6-3
Daytime Running

Lamps (DRL) . . . . . . . . . . . . . . . . 6-3

Automatic Headlamp

System . . . . . . . . . . . . . . . . . . . . . . 6-3

Adaptive Forward

Lighting (AFL) . . . . . . . . . . . . . . . 6-4
Hazard Warning Flashers . . . . . 6-4
Turn and Lane-Change

Signals . . . . . . . . . . . . . . . . . . . . . . 6-4
Fog Lamps . . . . . . . . . . . . . . . . . . . . 6-5

Buick LaCrosse Owner Manual - 2012

Black plate (2,1)

6-2

Lighting

Exterior Lighting

Exterior Lamp Controls

The exterior lamp control is located on the instrument panel on the outboard side of the steering wheel. Turn the control to the following positions: O (Off): Turns off the exterior lamps. The knob returns to the AUTO position after it is released. Turn to off again to reactivate the AUTO mode.

AUTO (Automatic): Automatically turns the exterior lamps on and off, depending on outside lighting. ; (Parking Lamps): Turns on the parking lamps together with the following: . Sidemarker Lamps

Taillamps License Plate Lamps Instrument Panel Lights

5 (Headlamps): Turns on the headlamps together with the following: . Sidemarker Lamps

Taillamps License Plate Lamps Instrument Panel Lights

. Parking Lamps

Exterior Lamps Off Reminder A warning chime sounds if the driver door is opened while the ignition is off and the exterior lamps are on.

Headlamp High/ Low-Beam Changer 2 3 Headlamp High/Low‐Beam Changer: Push the turn signal/lane change lever away from you and release, to turn the high beams on. To return to low beams, push the lever again or pull it toward you and release.

This indicator light turns on in the instrument panel cluster when the high‐beam headlamps are on.

Buick LaCrosse Owner Manual - 2012

Black plate (3,1)

Flash-to-Pass To flash the high beams, pull the turn signal/lane change lever toward you, and release.

Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. Fully functional daytime running lamps are required on all vehicles first sold in Canada. The DRL system turns on the low-beam headlamps at a reduced brightness.

For vehicles with High Intensity Discharge (HID) headlamps, the dedicated DRL will come on when all of the following conditions are met:

The engine is running. The exterior lamp band is in AUTO. The light sensor determines it is daytime.

When the DRL are on, the low-beam headlamps will be on. The taillamps, sidemarker lamps, instrument panel lights, and other lamps will not be on. The DRL turn off when the headlamps are turned to O or the ignition is off.

Lighting

6-3

Automatic Headlamp System When the exterior lamp control is set to AUTO and it is dark enough outside, the headlamps come on automatically.

There is a light sensor located on top of the instrument panel. Do not cover the sensor; otherwise the headlamps will come on when they are not needed. The system may also turn on the headlamps when driving through a parking garage or tunnel.

Buick LaCrosse Owner Manual - 2012

Black plate (4,1)

6-4

Lighting

When it is bright enough outside, the headlamps will turn off or may change to Daytime Running Lamps (DRL). The automatic headlamp system turns off when the exterior lamp control is turned to O or the ignition is off.

Adaptive Forward Lighting (AFL) The Adaptive Forward Lighting System (AFL) pivots the headlamps horizontally to provide greater road illumination while turning. To enable AFL, set the exterior lamp switch to the AUTO position. Moving the switch out of the AUTO position deactivates the system. AFL operates when the vehicle speed is greater than 3 km/h (2 mph). AFL does not operate when the transmission is in R (Reverse). AFL is not immediately operable after starting the vehicle;

driving a short distance is required to calibrate the AFL. See Exterior Lamp Controls on page 6‑2.

Hazard Warning Flashers

Turn and Lane-Change Signals

Move the lever all the way up or down to signal a turn. An arrow on the instrument panel cluster flashes in the direction of the turn or lane change. Raise or lower the lever until the arrow starts to flash to signal a lane change. Hold it there until the lane change is completed. If the lever is briefly pressed and released, the turn signal flashes three times.

| Hazard Warning Flasher: Press this button to make the front and rear turn signal lamps flash on and off. Press again to turn the flashers off. The hazard warning flashers turn on automatically if the airbags deploy.

Buick LaCrosse Owner Manual - 2012

Black plate (5,1)

The turn and lane‐change signal can be turned off manually by moving the lever back to its original position. If after signaling a turn or lane change the arrow flashes rapidly or does not come on, a signal bulb might be burned out. Have the bulbs replaced. If the bulb is not burned out, check the fuse. See Fuses and Circuit Breakers on page 10‑36.

Fog Lamps

For vehicles with fog lamps, the button is located on the exterior lamp control, left of the steering wheel.

Lighting

6-5

To turn on the fog lamps, the ignition and the headlamps or parking lamps must be on. If the fog lamps are turned on while the exterior lamp switch is in the AUTO position, the headlamps come on automatically. # : Press to turn on or off. An indicator light on the instrument panel cluster comes on when the fog lamps are on. Some localities have laws that require the headlamps to be on along with the fog lamps.

Buick LaCrosse Owner Manual - 2012

Black plate (6,1)

6-6

Lighting

Interior Lighting

Dome Lamps

Instrument Panel Illumination Control

Reading Lamps There are front and rear reading lamps.

The brightness of the instrument panel lighting and steering wheel controls can be adjusted. D (Instrument Panel Illumination) : Move and hold the thumbwheel up or down to brighten or dim the lights.

The interior lamps control located in the overhead console controls both the front and rear interior lamps. To operate: ( (Off): Turns the lamps off. H (Door): Turns the lamps on when any door is opened. ' (On): Keeps the lamps on all the time. The interior lamps turn on automatically if the airbags are deployed.

The front reading lamps are located in the overhead console. # or$ : Press to turn each lamp on or off.

Buick LaCrosse Owner Manual - 2012

Black plate (7,1)

The rear reading lamps are located in the headliner.

Sun Visor Lamps This lamp turns on when the cover is opened.

Lighting Features

Entry Lighting The headlamps, taillamps, license plate lamps, back‐up lamps, dome lamps, and most of the interior lights turn on briefly when the Remote Keyless Entry (RKE) K button is pressed, or when the door handle is pulled on a keyless access vehicle. See Ignition Positions (Key Access) on page 9‑16 or Ignition Positions (Keyless Access) on page 9‑18. After about 30 seconds the exterior lamps turn off, then the dome lamps and remaining interior lights dim to off. Entry lighting can be disabled manually by changing the ignition out of the OFF position, or by pressing the RKE Q button. This feature can be changed. See Vehicle Personalization on page 5‑40.

Lighting

6-7

Exit Lighting The headlamps, taillamps, parking lamps, back‐up lamps, and license plate lamps come on at night, or in areas with limited lighting, when the key is removed from the ignition. The dome lamps also come on when the key is removed from the ignition. The exterior lights and dome lamps remain on after the door is closed for a set amount of time, then automatically turn off. For vehicles with keyless access, the exterior lights and dome lamps automatically turn on when a door is opened after the ignition is turned off. See Ignition Positions (Key Access) on page 9‑16 or Ignition Positions (Keyless Access) on page 9‑18. The exterior lights turn off immediately by turning the exterior lamps control off. This feature can be changed. See Vehicle Personalization on page 5‑40.

Buick LaCrosse Owner Manual - 2012

Black plate (8,1)

6-8

Lighting

Battery Load Management The vehicle has Electric Power Management (EPM) that estimates the battery's temperature and state of charge. It then adjusts the voltage for best performance and extended life of the battery. When the battery's state of charge is low, the voltage is raised slightly to quickly bring the charge back up. When the state of charge is high, the voltage is lowered slightly to prevent overcharging. If the vehicle has a voltmeter gauge or a voltage display on the Driver Information Center (DIC), you may see the voltage move up or down. This is normal. If there is a problem, an alert will be displayed.

The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all of the power needed for very high electrical loads. A high electrical load occurs when several of the following are on, such as: headlamps, high beams, fog lamps, rear window defogger, climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets. EPM works to prevent excessive discharge of the battery. It does this by balancing the generator's output and the vehicle's electrical needs. It can increase engine idle speed to generate more power whenever needed. It can temporarily reduce the power demands of some accessories.

Normally, these actions occur in steps or levels, without being noticeable. In rare cases at the highest levels of corrective action, this action may be noticeable to the driver. If so, a DIC message might be displayed, such as BATTERY SAVER ACTIVE, BATTERY VOLTAGE LOW, or LOW BATTERY. If one of these messages displays, it is recommended that the driver reduce the electrical loads as much as possible. See Driver Information Center (DIC) on page 5‑25.

Battery Power Protection The battery saver feature is designed to protect the vehicle's battery. If the exterior lamps or any interior light is left on and the ignition is turned off, the battery rundown protection system automatically turns the lamp off after about 10 minutes.

Buick LaCrosse Owner Manual - 2012

Black plate (1,1)

Infotainment System

Introduction

Infotainment . . . . . . . . . . . . . . . . . . . 7-2
Theft-Deterrent Feature . . . . . . . 7-3
Overview (Radio with CD) . . . . . 7-4
Overview (Radio with CD/

DVD and MEM) . . . . . . . . . . . . . . 7-6

Overview (Radio with CD and

Touchscreen) . . . . . . . . . . . . . . . . 7-8
Operation . . . . . . . . . . . . . . . . . . . . 7-12

Infotainment System 7-1

Radio

Audio Players

AM-FM Radio (Radio with CD/

DVD/MEM) . . . . . . . . . . . . . . . . . 7-17

AM-FM Radio (Radio with CD

and Touchscreen) . . . . . . . . . . 7-19
Satellite Radio . . . . . . . . . . . . . . . 7-23
Radio Reception . . . . . . . . . . . . . 7-24
Backglass Antenna . . . . . . . . . . 7-25
Satellite Radio Antenna . . . . . . 7-26

CD Player . . . . . . . . . . . . . . . . . . . 7-26
CD/DVD Player . . . . . . . . . . . . . . 7-29
MP3 . . . . . . . . . . . . . . . . . . . . . . . . . 7-32
Mass Storage

Media (MEM) . . . . . . . . . . . . . . . 7-35

Auxiliary Devices

Auxiliary Devices

(Radio with CD) . . . . . . . . . . . . 7-38

(Radio with CD/DVD and MEM) . . . . . . . . . . . . . . . . . . 7-41

Auxiliary Devices

(Radio with CD and Touchscreen) . . . . . . . . . . . . . . . 7-44

Buick LaCrosse Owner Manual - 2012

Black plate (2,1)

7-2

Infotainment System

Rear Seat Infotainment Rear Seat Entertainment

(RSE) System . . . . . . . . . . . . . . 7-47

Phone

Bluetooth (Overview) . . . . . . . . 7-57
Bluetooth (Infotainment

Controls) . . . . . . . . . . . . . . . . . . . 7-59

Bluetooth (Voice

Bluetooth (UHP

Recognition) . . . . . . . . . . . . . . . 7-64

Mexico Only) . . . . . . . . . . . . . . . 7-70

Trademarks and License Agreements

Trademarks and License

Agreements . . . . . . . . . . . . . . . . 7-81

To minimize taking your eyes off the road while driving, do the following while the vehicle is parked: . Become familiar with the

operation and controls of the audio system.

. Set up the tone, speaker

adjustments, and preset radio stations.

For more information, see Defensive Driving on page 9‑3.

Introduction

Infotainment Read the following pages to become familiar with the audio system's features.

{ WARNING

Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to entertainment tasks while driving.

This system provides access to many audio and non‐audio listings.

Buick LaCrosse Owner Manual - 2012

Black plate (3,1)

Navigation System For vehicles with a navigation system, see the separate navigation manual.

Infotainment System 7-3

Theft-Deterrent Feature The theft-deterrent feature works by learning a portion of the Vehicle Identification Number (VIN) to the infotainment system. The infotainment system does not operate if it is stolen or moved to a different vehicle.

Notice: Contact your dealer before adding any equipment. Adding audio or communication equipment could interfere with the operation of the engine, radio, or other systems, and could damage them. Follow federal rules covering mobile radio and telephone equipment. The vehicle has Retained Accessory Power (RAP). With RAP, the audio system can be played even after the ignition is turned off. See Retained Accessory Power (RAP) on page 9‑25 for more information.

Buick LaCrosse Owner Manual - 2012

Black plate (4,1)

7-4

Infotainment System

Overview (Radio with CD)

A. VOL/ O

Turns the system on or off and adjusts the volume.

B. FAV

Radio: Opens the favorites list.

C. Buttons 1 to 6

Radio: Saves and selects favorite stations.

D.

INFO

Radio: Shows available information about the current station. CD: Shows available information about the current track.

E. TUNE

Radio: Manually selects radio stations. CD: Selects tracks.

Buick LaCrosse Owner Manual - 2012

Black plate (5,1)

F. CD/AUX

J. RADIO/BAND

N. / BACK

Infotainment System 7-5

Selects the CD player or an external audio source.

G. g

Radio: Seeks the previous station. CD: Select the previous track or rewinds within a track.

Changes the band while listening to the radio. Selects the radio when listening to a different audio source.

K. Menu Knob

Opens menus, highlights menu items, or sets numeric values while in a menu.

Removes a disc from the CD slot.

L. SELECT

Selects menu items.

M. CONFIG

Opens the Settings menu.

Radio: Seeks the next station. CD: Select the next track or fast forwards within a track.

H. X

I. l

Menu: Moves one level back. Character Input: Deletes the last character.

O. H

Opens the Clock menu.

P. TONE

Opens the Tone menu.

Q. 5

Opens the Phone main menu. Mutes the audio system.

Buick LaCrosse Owner Manual - 2012

Black plate (6,1)

7-6

Infotainment System

Overview (Radio with CD/DVD and MEM)

A. VOL/ O

Turns the system on or off and adjusts the volume.

B. FAV

Radio: Opens the favorites list. MEM: Opens the favorites list.

C. Buttons 1 to 6

Radio: Saves and selects favorite stations. MEM: Saves and selects favorite tracks and playlists.

D.

INFO

Radio: Shows available information about the current station. CD: Shows available information about the current track.

Buick LaCrosse Owner Manual - 2012

Black plate (7,1)

E. TUNE/ k

G. g

J. DEL

Infotainment System 7-7

Manually selects radio stations and pauses time shifted content. CD/DVD: Select tracks, pauses playback, and stops playback. MEM: Select tracks and pauses playback.

F. RADIO/BAND

Changes the band while listening to the radio. Selects the radio when listening to a different audio source.

Radio: Seeks the previous station. CD: Selects the previous track or rewinds within a track. MEM: Selects the previous track or rewinds within a track.

H. X

Removes a disc from the CD slot.

I. REC O

AUX: Records content from audio CDs, MP3/ WMA CDs, and USB mass storage devices.

MEM: Deletes the current track from MEM.

K. l

Radio: Seeks the next station. CD: Selects the next track or fast forwards within a track. MEM: Selects the next track or fast forwards within a track.

L. SELECT

Selects menu items.

M. Menu Knob

Opens menus, highlights menu items, or sets numeric values while in a menu.

Buick LaCrosse Owner Manual - 2012

Black plate (8,1)

7-8

Infotainment System

N. / BACK

Q. CONFIG

Menu: Moves one level back. Character Input: Deletes the last character.

O. TONE

Opens the Settings menu.

R. 5

Opens the Phone main menu. Mutes the audio system.

Opens the Tone menu.

S. MEM/DVD/AUX

P. H

Opens the Clock menu.

Selects MEM, CD/DVD, USB, or a connected front or rear auxiliary audio source.

Overview (Radio with CD and Touchscreen)

Infotainment System Overview The infotainment system is controlled by using the Menu knob, SELECT button, preset buttons, and other buttons on the faceplate. The Menu knob can be turned and the SELECT button pressed to complete any of the highlighted screen functions. The preset buttons can be pressed to select the appropriate screen button function as shown on the display.

Buick LaCrosse Owner Manual - 2012

Black plate (9,1)

Infotainment System 7-9

INFO

A. VOL/ O (Power/Volume) B. FAV (Favorites) C. Buttons 1 to 6
D. E. TUNE/ k F. F (Home Page) G. g H. X (Eject) I. CD Slot J. l K. SOURCE L. Menu Knob M. SELECT N. CONFIG O. / BACK P. H Q. TONE R. 5 (Phone menu)

Buick LaCrosse Owner Manual - 2012

Black plate (10,1)

7-10

Infotainment System

Config Setup Menu The Config setup menu is used for changing the options for the audio, display, vehicle configuration, phone, and time. Press the CONFIG button to display the Config Menu, then turn the Menu knob to scroll through the features. Once the desired feature displays, press the Menu knob to display more options within that feature. Languages The vehicle supports English, French (Canadian), and Spanish. The default language is English. Turn the Menu knob to highlight the language. Press SELECT to change the display language.

English and Metric Unit Conversion To change the display units between English and metric units. See Driver Information Center (DIC) on page 5‑25 for more information. Menu System

Controls The Menu knob, SELECT button, and the / BACK button are used to navigate the menu system. SELECT: Press to: . Enter the menu system. . Select or activate the highlighted

menu option.

. Confirm a set value.

Turn a system setting on or off.

Menu Knob: Turn to: . Highlight a menu option. . Select a value. / BACK : Press to: . Exit a menu. . Return from a submenu screen

to the previous menu screen. . Delete the last character in a

sequence.

Selecting a Menu Option

1. Turn the Menu knob to move the

highlighted bar.

2. Press SELECT to select the

highlighted option.

Buick LaCrosse Owner Manual - 2012

Black plate (11,1)

Submenus

Setting a Value

Entering a Character Sequence

Infotainment System 7-11

An arrow on the right‐hand edge of the menu indicates that it has a submenu with other options.

1. Turn the Menu knob to change the current value of the setting.

1. Turn the Menu knob to highlight

the character.

2. Press SELECT to confirm the

2. Press SELECT to select the

Activating a Setting

setting.

character.

Turning a Function On or Off

Press / BACK to delete the last character in the sequence or press and hold to delete the entire character sequence.

1. Turn the Menu knob to highlight

the setting.

1. Turn the Menu knob to highlight

2. Press SELECT to activate the

the function.

setting.

2. Press SELECT to turn the

function on or off.

Buick LaCrosse Owner Manual - 2012

Black plate (12,1)

7-12

Infotainment System

Storing Radio Station Presets Up to 36 preset stations can be stored. AM, FM, and XM™ (if equipped) can be mixed. To store presets: 1. Press VOL/ O to turn the

system on.

2. Select the SOURCE button. 3. Press g or l on the faceplate

or turn and press SELECT to select a station.

4. Press and hold one of the preset buttons for more than one and a half seconds.

5. Repeat the steps for each

preset.

To change the number of preset pages, see AM-FM Radio (Radio with CD/DVD/MEM) on page 7‑17 or AM-FM Radio (Radio with CD and Touchscreen) on page 7‑19 for more information.

Cleaning the Display Notice: Using abrasive cleaners when cleaning glass surfaces could scratch the glass. Use only a soft cloth and do not spray cleaner directly on the system as it could affect the mechanical parts. Do not apply spray cleaner directly to the system, the cleaner could affect the mechanical parts. Do not wipe the panel with a hard cloth or use a volatile liquid such as paint thinner, it could scratch the surface or erase the characters on the buttons.

Operation

Controls The infotainment system is operated by using the pushbuttons, multifunction knobs, menus shown on the display, and steering wheel controls, if equipped.

Turning the System On or Off VOL/ O (Volume/Power): Press to turn the system on and off.

Automatic Switch‐Off If the infotainment system has been turned on after the ignition is turned off, the system will turn off automatically after 10 minutes. Volume Control VOL/ O (Volume/Power): Turn to adjust the volume. 5 (Phone/Mute): For vehicles with OnStar®, press and hold 5 to mute the infotainment system. Press and hold 5 again, or turn the VOL/ O knob to cancel mute. For vehicles without OnStar®, press 5 to mute the infotainment system. Press 5 again, or turn the VOL/ O knob to cancel mute.

Buick LaCrosse Owner Manual - 2012

Black plate (13,1)

Menu System

Controls The Menu knob, SELECT button, and / BACK button are used to navigate the menu system. Menu Knob: Turn to: . Enter the menu system. . Highlight a menu option. . Select a value. SELECT: Press to: . Select or activate the highlighted

menu option.

. Confirm a set value.

Turn a system setting on or off.

/ BACK: Press to: . Exit a menu. . Return from a submenu screen

to the previous menu screen. . Delete the last character in a

sequence.

Selecting a Menu Option

Infotainment System 7-13

Submenus

An arrow on the right‐hand edge of the menu indicates that it has a submenu with other options.

Activating a Setting

1. Turn the Menu knob to move the

highlighted bar.

2. Press SELECT to select the

1. Turn the Menu knob to highlight

highlighted option.

the setting.

2. Press SELECT to activate the

setting.

Buick LaCrosse Owner Manual - 2012

Black plate (14,1)

7-14

Infotainment System

Setting a Value

Entering a Character Sequence

3. Press and hold SELECT until

the value changes to 0.

Press the / BACK button to go back to the Tone Settings menu.

Adjusting the Treble, Midrange, and Bass

1. Press the TONE button. 2. Select Treble, Midrange,

or Bass.

3. Select the value. Press the / BACK button to go back to the Tone Settings menu.

1. Turn the Menu knob to change the current value of the setting.

1. Turn the Menu knob to highlight

the character.

2. Press SELECT to confirm the

2. Press SELECT to select the

setting.

character.

Turning a Function On or Off

1. Turn the Menu knob to highlight

the function.

2. Press SELECT to turn the

function on or off.

Press the / BACK button to delete the last character in the sequence or press and hold to delete the entire character sequence. Audio Settings The audio settings can be set for each radio band and each audio player source. To quickly reset an audio setting value to 0: 1. Press the TONE button. 2. Select the audio setting.

Buick LaCrosse Owner Manual - 2012

Black plate (15,1)

3. Select the setting. Press the / BACK button to go back to the Tone Settings menu.

DSP (Digital Signal Processing) Settings For vehicles with DSP, it is used to provide a choice of different listening experiences. The DSP settings for the radio with CD are:

normal ‐ Select this setting to adjust the audio for stereo mode. This provides the best sound quality for the driver seat first, with the front passenger second. hk surround ‐ Select to enable hk surround. This produces a true 6.1 matrix surround from any two channel digital source. This feature is not available in AM/FM radio mode.

Infotainment System 7-15

The DSP settings for the radio with CD/DVD and MEM are:

2.0 normal ‐ Select this setting to adjust the audio for stereo mode. This provides the best sound quality for the driver seat first, with the front passenger second. hk surround ‐ Select to enable hk surround. This produces a true 6.1 matrix surround from any two channel digital source. This feature is not available in AM/FM radio mode.

To adjust the DSP settings: 1. Press the TONE button. 2. Select DSP. 3. Select the setting. Press the / BACK button to go back to the Tone Settings menu.

Adjusting the Fader and Balance

1. Press the TONE button. 2. Select Fader or Balance. 3. Select the value. Press the / BACK button to go back to the Tone Settings menu.

Adjusting the EQ (Equalizer) For vehicles with an equalizer:

1. Press the TONE button. 2. Select EQ.

Buick LaCrosse Owner Manual - 2012

Black plate (16,1)

7-16

Infotainment System

System Settings

Configuring the Number of Favorite Pages

To configure the number of available favorite pages: 1. Press the CONFIG button. 2. Select Radio Settings. 3. Select Radio Favorites. 4. Select the number of available

favorite pages.

5. Press the / BACK button to

go back to the System Configuration menu.

Maximum Startup Volume The maximum volume played when the radio with CD is first turned on can be set.

Auto Volume The auto volume feature automatically adjusts the radio volume to compensate for road and wind noise as the vehicle speeds up or slows down, so that the volume level is consistent. The level of volume compensation can be selected, or the auto volume feature can be turned off.

1. Press the CONFIG button. 2. Select Radio Settings. 3. Select Maximum Startup

Volume.

4. Select the setting. 5. Press the / BACK button to

go back to the System Configuration menu.

1. Press the CONFIG button. 2. Select Radio Settings. 3. Select Auto Volume. 4. Select the setting. 5. Press the / BACK button to

go back to the System Configuration menu.

Buick LaCrosse Owner Manual - 2012

Black plate (17,1)

Radio

AM-FM Radio (Radio with CD/DVD/MEM)

Control Buttons The buttons used to control the radio are: RADIO/BAND: Press to turn the radio on and choose between AM, FM, and XM™, if equipped. Menu Knob: Turn to navigate the available menus. TUNE: Turn to search for stations.