2016 Buick Enclave Owners Manual

and the second 10-minute time frame will start. For example, if Q and then / are pressed again after the vehicle has been running for five minutes, 10 minutes are added, allowing the engine to run for a total of 15 minutes. A maximum of two remote starts or remote start attempts are allowed between ignition cycles. After the vehicle's engine has been started two times using the remote start button, the ignition must be turned on and then back off before the remote start procedure can be used again. Canceling a Remote Start To manually shut off a remote start: . Press and hold / until the

parking lamps turn off.

. Turn on the hazard warning

flashers.

. Turn the ignition switch on and

then off.

Conditions in Which the Remote Start Will Not Work The vehicle cannot be started using the remote start feature if the key is in the ignition, the hood is open, or there is an emission control system malfunction. The engine turns off during a remote start if the coolant temperature gets too high or if the oil pressure gets low.

Door Locks

{ Warning Unlocked doors can be dangerous.

. Passengers, especially

children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. The chance

(Continued)

Warning (Continued)

of being thrown out of the vehicle in a crash is increased if the doors are not locked. So, all passengers should wear safety belts properly and the doors should be locked whenever the vehicle is driven.

. Young children who get into

unlocked vehicles may be unable to get out. A child can be overcome by extreme heat and can suffer permanent injuries or even death from heat stroke. Always lock the vehicle whenever leaving it.

. Outsiders can easily enter through an unlocked door when you slow down or stop the vehicle. Locking the doors can help prevent this from happening.

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

32

Keys, Doors, and Windows

To lock or unlock a door manually: . From the inside use the door lock knob on the window sill. . From the outside turn the key toward the front or rear of the vehicle, or press the or button on the Remote Keyless Entry (RKE) transmitter.

Power Door Locks

K (Unlock) : Press to unlock the doors. Q (Lock) : Press to lock the doors.

Delayed Locking This feature delays the locking of the doors until five seconds after all doors are closed. When Q is pressed on the power door lock switch while the door or liftgate is open, a chime will sound three times indicating delayed locking is active. The doors will lock automatically five seconds after all doors are closed. If a door is reopened before that time, the five-second timer will reset when all doors are closed again. Press Q on the door lock switch again or press Q on the RKE transmitter to lock doors immediately. This feature can also be programmed. See Vehicle Personalization 0 133.

Automatic Door Locks The doors will lock automatically when all doors are closed, the ignition is on, and the shift lever is moved out of P (Park). To unlock the doors: . Press K on a door. . Shift the transmission into

P (Park).

Automatic door unlocking can be programmed through the Driver Information Center (DIC). See Vehicle Personalization 0 133.

Lockout Protection When locking is requested with the driver door open and the key in the ignition, all the doors will lock and then the driver door will unlock. This can be manually overridden by pressing and holding Q on the power door lock switch.

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

Keys, Doors, and Windows

33

Safety Locks

Caution

Pulling the inside door handle while the rear door safety locks are engaged could damage your vehicle. Do not pull the inside door handle while the rear door safety locks are engaged.

The vehicle has rear door security locks to prevent passengers from opening the rear doors from the inside.

Open the rear doors to access the security locks on the inside edge of each door. To set the locks, insert a key into the slot and turn it to the horizontal position. The door can only be opened from the outside with the door unlocked. To return the door to normal operation, turn the slot to the vertical position.

Doors

Liftgate

{ Warning

Exhaust gases can enter the vehicle if it is driven with the liftgate or trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate. Engine exhaust contains carbon monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. If the vehicle must be driven with the liftgate or trunk/hatch open: . Close all of the windows. . Fully open the air outlets on

or under the instrument panel.

. Adjust the climate control

system to a setting that brings in only outside air

(Continued)

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

34

Keys, Doors, and Windows

Warning (Continued)

and set the fan speed to the highest setting. See “Climate Control Systems” in the Index. If the vehicle is equipped with a power liftgate, disable the power liftgate function.

See Engine Exhaust 0 201.

Caution

To avoid damage to the liftgate or liftgate glass, make sure the area above and behind the liftgate is clear before opening it.

Manual Liftgate To unlock the liftgate, press the power door lock switch or press K on the Remote Keyless Entry (RKE) transmitter twice. See Remote Keyless Entry (RKE) System Operation 0 28.

To open the liftgate, press the touch pad under the liftgate handle and lift up. The vehicle must be in P (Park) and the battery must be charged. Use the pull cup or pull strap to lower and close the liftgate. Always close the liftgate before driving. Power Liftgate If equipped with a power liftgate, the vehicle must be in P (Park) to operate. The taillamps flash and a chime sounds when the power liftgate moves.

{ Warning

You, or others, could be injured if caught in the path of the power liftgate. Make sure there is no one in the way of the liftgate as it is opening and closing.

The power liftgate can be power opened and closed in the following ways: . Press and hold 8 on the

RKE transmitter. See Remote Keyless Entry (RKE) System Operation 0 28.

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

Keys, Doors, and Windows

35

Pressing any liftgate switch a second time while the liftgate is moving reverses the direction. The power liftgate may be temporarily disabled under extreme temperatures or under low battery conditions. If this occurs, the liftgate can be operated manually. If the vehicle is shifted out of P (Park) while the liftgate power function is in progress, it will continue to completion. If the vehicle is shifted out of P (Park) and accelerated before the power liftgate latch closes, the liftgate may reverse to the open position. Cargo could fall out of the vehicle. Always make sure the power liftgate is closed and latched before driving away. If after a power opening, the liftgate stays open momentarily, then slowly closes with continuous chiming sounds and turn signal flashes, the support strut may have lost pressure. See your dealer for service before using the liftgate.

Obstacle Detection Features If an obstacle is encountered during the power open or close cycle, a warning chime will sound and the liftgate will automatically reverse direction to the full closed or open position. After removing the obstacle the liftgate will resume normal operation. If more obstacles are encountered on the same power cycle, the power function deactivates. The liftgate must be opened or closed manually if this occurs. A message displays on the Driver Information Center (DIC) to indicate that the liftgate is open. See Door Ajar Messages 0 125. After removing the obstacles, manually open the liftgate fully or close and latch the liftgate. The liftgate will resume normal power operation. The vehicle also has pinch sensors along the side edges of the liftgate. If the sensors press against an object while closing, the liftgate will reverse direction and open fully. The liftgate will remain open until it is activated again or closed manually.

. Press O.

. Press l on the inside edge of

the liftgate.

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

36

Keys, Doors, and Windows

Do not force the liftgate open or closed during a power cycle. Manual Operation of Power Liftgate

To change the liftgate to manual operation, press OFF on the power liftgate switch. A message displays on the DIC indicating manual operation mode. See Door Ajar Messages 0 125. With the liftgate in manual mode and all of the doors unlocked, the liftgate can be manually opened and closed.

Press the touch pad on the outside of the liftgate pull cup and lift to open. Use the pull cup to lower and close the liftgate. The liftgate latch will power close. Always close the liftgate before driving. If 8 on the RKE transmitter or l on the liftgate is pressed while in manual operation mode, the taillamps will flash three times, but the liftgate will not move. It is not recommended to drive with the liftgate open. However, if the vehicle must be driven with the liftgate open, the liftgate should be set to manual operation.

Vehicle Security This vehicle has theft-deterrent features; however, they do not make the vehicle impossible to steal.

Vehicle Alarm System On vehicles with an anti-theft alarm system, to activate the system: . Press Q on the Remote Keyless

Entry (RKE) transmitter or the power door lock switch when any door is open.

The security light flashes. When the door is closed, the security light stops flashing and stays on solid for approximately 30 seconds. The content theft-deterrent alarm is not armed until the security light goes off.

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

If the delayed locking feature is active, the alarm is not activated until all doors are closed and the security light goes off.

. Press Q when the driver door is closed. The security light comes on solid for approximately 30 seconds and then goes off. The content theft-deterrent alarm is not armed until the security light goes off.

The theft-deterrent system will not activate if the doors are locked with the vehicle's key or the manual door lock. If the driver door is opened without first unlocking with the RKE transmitter, the horn will chirp and the lights will flash to indicate pre-alarm. If the vehicle is not started, or the door is not unlocked by pressing K on the RKE transmitter during the 10-second pre-alarm, the alarm will be activated. The alarm will also be activated if a passenger door, the liftgate, or the hood is opened without first

Keys, Doors, and Windows

37

disarming the system. When the alarm is activated, the turn signals flash and the horn sounds for about 30 seconds. The alarm system will then re-arm to monitor for the next unauthorized event. The vehicle can be started with the correct ignition key if the alarm has been set off. To avoid setting off the alarm by accident: . Lock the vehicle with the door key after the doors are closed. . Unlock the door with the RKE

transmitter. Unlocking a door any other way sets off the alarm if the system has been armed. Press K or place the key in the ignition and turn it to START to turn off the alarm. Testing the Alarm To test the alarm: 1. From inside the vehicle, lower

the driver side window, and open the driver door.

2. Press Q.

3. Get out of the vehicle, close

the door, and wait for the security light to go out.

4. Reach in through the window,

unlock the door with the manual door lock, and open the door. This should set off the alarm.

If the alarm does not sound when it should, but the headlamps flash, check to see if the horn works. The horn fuse may be blown. To replace the fuse, see Fuses and Circuit Breakers 0 257. If the alarm does not sound or the headlamps do not flash, see your dealer for service.

Immobilizer See Radio Frequency Statement 0 336.

Immobilizer Operation This vehicle has PASS-Key® III+ (Personalized Automotive Security System) theft-deterrent system. PASS-Key III+ is a passive theft-deterrent system.

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

38

Keys, Doors, and Windows

The system is automatically armed when the key is removed from the ignition. The system is automatically disarmed when the key is turned to ON/RUN, ACC/ACCESSORY, or START from the LOCK/OFF position. You do not have to manually arm or disarm the system. The security light comes on if there is a problem with arming or disarming the theft-deterrent system. When the PASS-Key III+ system senses an incorrect key, the vehicle does not start. Anyone using a trial-and-error method to start the vehicle will be discouraged because of the high number of electrical key codes. If the engine does not start and the security light on the instrument panel comes on when trying to start the vehicle, there may be a problem with the theft-deterrent system. Turn the ignition off and try again.

If the engine still does not start, and the key appears to be undamaged, try another ignition key and check the fuses. See Fuses and Circuit Breakers 0 257 for additional information. If the engine still does not start with the other key, the vehicle needs service. If the vehicle does start, the first key may be faulty. See your dealer who can service the PASS-Key III+ to have a new key made. In an emergency, contact Roadside Assistance. See Roadside Assistance Program 0 330. It is possible for the PASS-Key III+ decoder to learn the transponder value of a new or replacement key. Up to 10 keys may be programmed to the vehicle. The following procedure is for programming additional keys only. If all currently programmed keys are lost or do not operate, you must see your dealer or a locksmith who can service PASS-Key III+ to have keys made and programmed to the system.

See your dealer or a locksmith who can service PASS-Key III+ to get a new key blank that is cut exactly as the ignition key that operates the system. To program the new additional key: 1. Verify that the new key has a

2.

1 stamped on it. Insert the already programmed key in the ignition and start the engine. If the engine does not start, see your dealer for service.

3. After the engine has started,

4.

turn the key to LOCK/OFF, and remove the key. Insert the key to be programmed and turn it to the ON/RUN position within five seconds of the original key being turned to the LOCK/OFF position. The security light turns off once the key has been programmed.

5. Repeat Steps 1–4 if additional

keys are to be programmed.

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

If the PASS-Key III+ key is lost or damaged, see your dealer or a locksmith to have a new key made. The SERVICE THEFT DETERRENT SYSTEM message displays on the Driver Information Center (DIC) when there is a problem with the theft-deterrent system. See Security Messages 0 130 for additional information. Do not leave the key or device that disarms or deactivates the theft-deterrent system in the vehicle.

Keys, Doors, and Windows

39

Exterior Mirrors

Power Mirrors

Convex Mirrors

{ Warning

A convex mirror can make things, like other vehicles, look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on the right. Check the inside mirror or glance over your shoulder before changing lanes.

The passenger side mirror is convex shaped. A convex mirror's surface is curved so more can be seen from the driver seat.

To adjust each mirror: 1. Press (1) or (2) to select the

mirror.

2. Press on the control pad to

adjust the mirror.

3. Press (1) or (2) again to

deselect the mirror.

Side Blind Zone Alert (SBZA) If the vehicle has the Side Blind Zone Alert (SBZA) system, see Side Blind Zone Alert (SBZA) 0 217.

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

40

Keys, Doors, and Windows

Folding Mirrors For vehicles with manual folding mirrors, push the mirror toward the vehicle. Pull the mirror out to return to its original position. For vehicles with outside power folding mirrors:

1. Press (1) to fold the mirrors out

to the driving position.

2. Press (2) to fold the mirrors in

to the folded position.

Resetting the Power Folding Mirrors Reset the power folding mirrors if:

Park Tilt Mirrors If equipped with memory seats, the passenger and/or driver mirror tilts to a preselected position when the vehicle is in R (Reverse). This allows the curb to be seen when parallel parking. The mirror(s) return to the original position when: . The vehicle is shifted out of R (Reverse), or remains in R (Reverse) for about 30 seconds.

. The ignition is turned off. . The vehicle is driven in

R (Reverse) above a set speed.

To turn this feature on or off, see Vehicle Personalization 0 133.

. The mirrors are accidentally

obstructed while folding.

. They are accidentally manually

folded/unfolded.

. The mirrors vibrate at normal

driving speeds.

Fold and unfold the mirrors one time using the mirror controls to reset them to their normal position. A popping noise may be heard during the resetting of the power folding mirrors. This sound is normal after a manual folding operation.

Heated Mirrors For vehicles with heated mirrors: 1 (Rear Window Defogger) : Press to heat the mirrors. See “Rear Window Defogger” under Dual Automatic Climate Control System 0 175.

Automatic Dimming Mirror The driver outside mirror automatically adjusts for the glare of headlamps from behind.

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

Interior Mirrors

Windows

Interior Rearview Mirrors Adjust the rearview mirror for a clear view of the area behind your vehicle. If equipped with OnStar, the vehicle may have three control buttons at the bottom of the mirror. See your dealer for more information about OnStar and how to subscribe to it. See “OnStar,” if equipped. Do not spray glass cleaner directly on the mirror. Use a soft towel dampened with water.

Automatic Dimming Rearview Mirror If equipped, automatic dimming reduces the glare of the headlamps from behind. This feature comes on when the vehicle is started.

{ Warning

Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke.

The vehicle aerodynamics are designed to improve fuel economy performance. This may result in a

Keys, Doors, and Windows

41

pulsing sound when either rear window is down and the front windows are up. To reduce the sound, open either a front window or the sunroof, if equipped.

Power Windows

{ Warning

Children could be seriously injured or killed if caught in the path of a closing window. Never leave keys in a vehicle with children. When there are children in the rear seat, use the window lockout button to prevent operation of the windows. See Keys 0 26.

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

42

Keys, Doors, and Windows

3. Pull up and hold the window switch to close the window. Continue to hold it briefly after the window is fully closed.

4. Repeat for each window that has the express-up feature.

Anti-Pinch Feature The anti-pinch feature is on windows with the express-up feature. If an object is in the way of the window as it is express-closing, or in certain weather conditions like severe icing, the window will stop and open to a factory preset position. The window functions normally once the obstruction is removed.

Express-Up/Express-Down Windows A window with the express-up/down feature allows it to be raised or lowered without holding the switch. Press or pull the window switch fully and release it to activate the express feature. The express mode can be canceled by pressing or pulling the switch. Programming the Power Windows If the vehicle battery has been recharged, disconnected, or replaced, windows with the express-up feature may need to be reprogrammed for this feature to work. To program the window: 1. Close all doors with the ignition

in the ACC/ACCESSORY or ON/RUN position, or with Retained Accessory Power (RAP) active. See Retained Accessory Power (RAP) 0 199.

2. Press and continue to hold the window switch until the window is fully open.

Uplevel Shown, Base Similar The driver door has switches that control the passenger and rear windows. The power windows work with the ignition in ACC/ ACCESSORY or ON/RUN or with Retained Accessory Power (RAP) active. See Retained Accessory Power (RAP) 0 199. Press the switch to lower the window. Pull up on the front edge of the switch to raise the window.

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

Rear Window Lockout

Sun Visors

Roof

Keys, Doors, and Windows

43

Sunroof On vehicles with a sunroof, the sunroof only operates when the ignition is in ON/RUN or ACC/ ACCESSORY, or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) 0 199. If equipped, there may be a rear sunroof over the second row seats. The rear sunroof does not open.

Pull the sun visor down to block glare. Detach the sun visor from the center mount to pivot to the side window or, if equipped, extend along the rod.

The rear window lockout feature prevents the rear passenger windows from operating, except from the driver position. Press v to activate the rear window lockout switch. The indicator light comes on when activated. Press v again to deactivate the lockout switch.

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

44

Keys, Doors, and Windows

Vent : Press and hold the front of the switch to vent the sunroof. Press and hold the rear of the switch to close the sunroof. Express-open/Express-close : Press and release the rear of the switch to express-open the sunroof. Press and release the front of the switch to express-close the sunroof. Manual Sunshade The sunshades must be opened and closed manually. To open the sunshade, press the button on the sunshade handle to release it and guide it back. To close the sunshade, pull the sunshade forward until it latches.

Dirt and debris may collect on the sunroof seal or in the track. This could cause an issue with sunroof operation or noise. It could also plug the water drainage system. Periodically open the sunroof and remove any obstacles or loose debris. Wipe the sunroof seal and roof sealing area using a clean cloth, mild soap, and water. Do not remove grease from the sunroof. If water is seen dripping into the water drainage system, this is normal.

Seats and Restraints

45

Replacing LATCH System Parts

After a Crash . . . . . . . . . . . . . . . . . 89

Securing Child Restraints

(Rear Seat) . . . . . . . . . . . . . . . . . . . 89

Securing Child Restraints (Front

Passenger Seat) . . . . . . . . . . . . . 91

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

Seats and Restraints

Replacing Safety Belt System

Parts after a Crash . . . . . . . . . . . 63

Airbag System

Head Restraints

Head Restraints . . . . . . . . . . . . . . . 46

Front Seats

Power Seat Adjustment . . . . . . . . 47
Lumbar Adjustment . . . . . . . . . . . . 48
Reclining Seatbacks . . . . . . . . . . . 48
Memory Seats . . . . . . . . . . . . . . . . . 49
Heated and Cooled Front

Seats . . . . . . . . . . . . . . . . . . . . . . . . . 50

Rear Seats

Rear Seats . . . . . . . . . . . . . . . . . . . . 52
Third Row Seats . . . . . . . . . . . . . . . 53

Safety Belts

Safety Belts . . . . . . . . . . . . . . . . . . . . 56
How to Wear Safety Belts

Properly . . . . . . . . . . . . . . . . . . . . . . 57
Lap-Shoulder Belt . . . . . . . . . . . . . 58
Safety Belt Use During

Pregnancy . . . . . . . . . . . . . . . . . . . . 62
Safety Belt Extender . . . . . . . . . . . 62
Safety System Check . . . . . . . . . . 63
Safety Belt Care . . . . . . . . . . . . . . . 63

Airbag System . . . . . . . . . . . . . . . . . 64
Where Are the Airbags? . . . . . . . 65
When Should an Airbag

Inflate? . . . . . . . . . . . . . . . . . . . . . . . 67

What Makes an Airbag

Inflate? . . . . . . . . . . . . . . . . . . . . . . . 68

How Does an Airbag

Restrain? . . . . . . . . . . . . . . . . . . . . . 68

What Will You See after an

Airbag Inflates? . . . . . . . . . . . . . . 68
Passenger Sensing System . . . 70
Servicing the Airbag-Equipped

Vehicle . . . . . . . . . . . . . . . . . . . . . . . 74

Adding Equipment to the

Airbag-Equipped Vehicle . . . . . 74
Airbag System Check . . . . . . . . . . 75
Replacing Airbag System Parts

after a Crash . . . . . . . . . . . . . . . . . 75

Child Restraints

Older Children . . . . . . . . . . . . . . . . . 76
Infants and Young Children . . . . 77
Child Restraint Systems . . . . . . . 80
Where to Put the Restraint . . . . . 81
Lower Anchors and Tethers for

Children (LATCH System) . . . . 83

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

46

Seats and Restraints

Head Restraints

Front Seats

{ Warning

With head restraints that are not installed and adjusted properly, there is a greater chance that occupants will suffer a neck/ spinal injury in a crash. Do not drive until the head restraints for all occupants are installed and adjusted properly.

The vehicle's front seats have adjustable head restraints in the outboard seating positions.

Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant's head. This position reduces the chance of a neck injury in a crash.

To raise or lower the head restraint, press the button located on the side of the head restraint, and pull up or push the head restraint down, and release the button. Pull and push on the head restraint after the button is released to make sure that it is locked in place. To adjust the head restraint forward, grasp the head restraint and pull forward until the desired locking position is reached. To adjust the head restraint rearward, press the button located on the side of the head restraint, and push the head restraint rearward until the desired locking

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

Front Seats

Power Seat Adjustment

{ Warning

You can lose control of the vehicle if you try to adjust a driver seat while the vehicle is moving. Adjust the driver seat only when the vehicle is not moving.

position is reached. Try to move the head restraint after the button is released to make sure that it is locked in place. The front seat outboard head restraints are not removable. Rear Seats The vehicle's second row seats have head restraints in the outboard seating positions that cannot be adjusted. The vehicle's third row seats have headrests in the outboard seating positions that cannot be adjusted. The second row head restraints and third row headrests are not removable.

Seats and Restraints

47

To adjust the seat: . Move the seat forward or

rearward by sliding the control (1) forward or rearward. . Raise or lower the front part of the seat cushion by moving the front of the control (1) up or down.

. Raise or lower the entire seat by moving the rear of the control (1) up or down.

. Adjust the seatback by tilting the

top of the control (2) forward or rearward. See Reclining Seatbacks 0 48. Increase or decrease lumbar support by pressing the front or rear of the control (3). See Lumbar Adjustment 0 48.

1. Seat Adjustment Control 2. Reclining Seatback Control 3. Lumbar Adjustment Control

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

48

Seats and Restraints

Lumbar Adjustment

Power Lumbar

Manual Lumbar

Reclining Seatbacks

Power Reclining Seatbacks

If equipped, move the handle forward or rearward to increase or decrease lumbar support.

If equipped, press and hold the front or rear of control to increase or decrease lumbar support. Release the control when the seatback reaches the desired level of lumbar support.

To adjust the seatback: . Tilt the top of the control

rearward to recline.

. Tilt the top of the control forward

to raise.

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

{ Warning

Sitting in a reclined position when the vehicle is in motion can be dangerous. Even when buckled up, the safety belts cannot do their job. The shoulder belt will not be against your body. Instead, it will be in front of you. In a crash, you could go into it, receiving neck or other injuries. The lap belt could go up over your abdomen. The belt forces would be there, not at your pelvic bones. This could cause serious internal injuries. For proper protection when the vehicle is in motion, have the seatback upright. Then sit well back in the seat and wear the safety belt properly.

Do not have a seatback reclined if the vehicle is moving.

Memory Seats

Seats and Restraints

49

If available, the controls on the driver door are used to program and recall memory settings for the driver seat, outside mirrors, and power steering column (if equipped).

Storing Memory Positions To save into memory: 1. Adjust the driver seat and

seatback recliner, both outside mirrors, and the power steering column (if equipped). Not all vehicles will have the ability to save and recall the mirror positions.

2. Press and hold 1 until

two beeps sound.

3. Repeat for a second driver

position using 2.

To recall, press and release 1 or 2. The vehicle must be in P (Park). A single beep will sound. The seat, outside mirrors, and power steering column (if equipped) will move to the positions previously stored for the identified driver.

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

50

Seats and Restraints

Memory Remote Recall The memory feature can recall the driver seat, outside mirrors, and power steering column (if equipped) to stored positions when entering the vehicle. To activate, unlock the driver door with the Remote Keyless Entry (RKE) transmitter. The driver seat, outside mirrors, and power steering column will move to the memory positions associated with the transmitter used to unlock the vehicle. This feature is turned on or off using the vehicle personalization menu. See Vehicle Personalization 0 133. To stop recall movement, press one of the power seat controls, memory buttons, power mirror buttons, or the power steering column control (if equipped). If something has blocked the driver seat and/or steering column while recalling a memory position, the recall may stop. Remove the obstruction; then press and hold the appropriate manual control for the

memory item that is not recalling for two seconds. Try recalling the memory position again by pressing the appropriate memory button. If the memory position is still not recalling, see your dealer for service.

Easy Exit Positions The easy exit feature can move the driver seat rearward and the power steering column (if equipped) up and forward to allow extra room to exit the vehicle. S (Easy Exit Positions) : Press to activate the recall. The vehicle must be in P (Park). If this feature is programmed on in the vehicle personalization menu, automatic driver seat and power steering column movement occur when the ignition key is removed. A single beep sounds. The driver seat moves back approximately 8 cm (3 in) and the power steering column (if equipped) moves up and forward. To move the seat back farther, press S again until the seat is all the way back.

If something has blocked the driver seat while recalling the exit position, the recall may stop. Remove the obstruction; then press and hold the power seat control rearward for two seconds. Try recalling the exit position again. If the exit position is still not recalling, see your dealer for service. See Vehicle Personalization 0 133.

Heated and Cooled Front Seats

{ Warning

If you cannot feel temperature change or pain to the skin, the seat heater may cause burns. To reduce the risk of burns, people with such a condition should use care when using the seat heater, especially for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket, cushion, cover, or similar item. This may

(Continued)

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

J (Heated Seat and Seatback) : Press to heat the seat and seatback. Press the button once for the highest setting. With each press of the button, the seat will change to the next lower setting, and then to the off setting. The lights indicate three for the highest setting and one for the lowest. The passenger heated seat may take longer to heat up. The heated and/or cooled seats are canceled after the ignition is turned off.

Seats and Restraints

51

Remote Start Heated Seats When it is cold outside, the heated seats may turn on automatically during a remote vehicle start. The heated seats will be canceled when the ignition is turned on. Press the desired heated seat button to use the heated seats after the vehicle is started. The heated seat button lights will not turn on during a remote start. The temperature of an unoccupied seat may be reduced. See Remote Vehicle Start 0 30.

Warning (Continued)

cause the seat heater to overheat. An overheated seat heater may cause a burn or may damage the seat.

Heated and Cooled Seat Buttons

Shown, Heated Seat Buttons

Similar

If equipped, the buttons are on the center stack. To operate, the engine must be running. I (Heated Seatback) : If equipped, press to heat the seatback only. H (Cooled Seat) : If equipped, press to cool the entire seat.

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

Warning (Continued)

stop or crash. Be sure to return the seat to the passenger seating position. Push and pull on the seat to make sure it is locked into place.

Caution

Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts. Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat.

52

Seats and Restraints

Rear Seats

1. Seat Adjustment Handle 2. Reclining Seatback Strap 3. Sliding Seat Lever

Entering and Exiting the Third Row

{ Warning

Using the third row seating position while the second row is folded, or folded and tumbled, could cause injury in a sudden

(Continued)

To access the third row: 1. Remove objects on the floor in

front of or on the second row seat, or in the seat tracks on the floor.

2. Move the front center console

armrest completely forward. See Center Console Storage 0 95.

3. Place the folding armrests in

the upright position.

4. Make sure that the safety belt

is unfastened and in the stowed position.

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

5. Pull the sliding seat lever (3) forward. The seatback will tilt forward, and the seat will begin sliding forward. Continue to push forward on the seatback until the entire seat moves all the way forward and the seat cushion is folded.

Returning the Seat to the Seating Position To return the second row seat to its normal seating position: 1. Remove objects on the floor

behind the second row seat or in the seat tracks on the floor.

2. Slide the seat rearward by

pushing on the seatback until the seat is locked into place.

3. Continue pushing the seatback

rearward until the seatback is locked into place.

4. Push down on the rear of the

seat cushion until it is locked in place.

5. Push and pull on the seatback and seat cushion to make sure they are locked in place.

6. Check that the safety belt is not under the seat cushion.

Reclining the Seatbacks To recline the seatback: 1. Leaning rearward in the seat,

pull the reclining seatback strap (2).

2. Move the seatback to the desired position, and then release the strap (2) to lock the seatback in place.

3. Push and pull on the seatback

to make sure it is locked.

Folding the Seatback To fold the second row seatbacks: 1. Remove anything on or under

the seat.

2. Place the armrest in the upright

position, and unfasten the safety belt.

3. Pull forward on the reclining

seatback strap (2). The head restraint will fold down automatically.

Seats and Restraints

53

To return the seatback to the seating position, lift the seatback and push it rearward until it locks into place. Push and pull on the seatback to make sure it is locked. Pull up on the head restraint to return it to the upright, locked position. Adjusting the Seats To adjust the second row seats, pull outward on the seat adjustment handle (1). Slide the seat forward or rearward to the desired position. Release the handle (1), and push and pull on the seat to make sure it is locked.

Third Row Seats

{ Warning

Using the third row seating position while the second row is folded, or pushed forward in the entry position, could cause injury in a sudden stop or crash. Be sure to return the seat to the

(Continued)

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

54

Seats and Restraints

Warning (Continued)

passenger seating position. Push and pull on the seat to make sure it is locked into place.

Folding the Seatback

Caution

Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts. Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat.

To fold the third row seatback: 1.

If the second row seat is in the full rear position, adjust it forward to allow the third row seat to fold fully flat.

2. Remove anything on or under

the seat.

3. Disconnect the rear safety belt

mini-latch, using a key in the slot on the mini-buckle, and let the belt retract into the headliner.

4. Stow the mini-latch in the

holder in the headliner.

5. Pull up on the release lever on

the back of the seat.

6. Push the seatback forward to

lay flat.

Returning the Seat to the Seating Position To return the seatback to the seating position: 1. From the rear of the vehicle,

raise the seatback to the upright position using the pull strap on the back of the third

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

Seats and Restraints

55

row seat, or lift the seatback and push it into place from inside the vehicle.

{ Warning

If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they are locked.

2. Push and pull on the seatback

to make sure it is locked in place.

{ Warning

A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection needed in a crash. The person wearing the belt could be seriously injured. After raising the rear seatback, always check to be (Continued)

Warning (Continued)

Caution (Continued)

sure that the safety belts are properly routed and attached, and are not twisted.

3. Reconnect the center safety

belt mini-latch to the mini-buckle. Do not let it twist.

4. Pull on the safety belt to be

sure the mini-latch is secure.

Removing the Third Row Seats To remove a third row seat: 1. Remove the cargo

management system, if it is installed. See Cargo Management System 0 96.

2. Remove anything on or under

the seat.

Caution

Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety

(Continued)

belts. Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat.

3. Fold the seatback down. See “Folding the Seatback” earlier in this section.

4. Remove the rear bolts on the floor on each side of the seat.

5. Remove the seat by tilting it

slightly upward, and then pulling it out of the rear of the vehicle in one motion.

6. Replace the bolts in the floor

holes for storage.

Installing the Third Row Seats To reinstall a third row seat: 1. Before installing the seat, the

seatback must be folded forward. See “Folding the Seatback” earlier in this section.

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

56

Seats and Restraints

The seats must be placed in the proper locations to attach correctly. The wider seat must be installed on the driver side and the narrower seat on the passenger side. Remove the bolts from the holes in the floor before installing the seats.

2. Place the seat on the vehicle

floor so that the front seat hooks are on the vehicle bars. 3. Reinstall the bolts, and torque to 55 Y (41 lb ft). Pull up on the seat to make sure it is locked in place.

4. Raise the seatback to its

upright position. Push and pull on the seatback to make sure it is locked into place.

5. Reconnect the center safety

belt mini-latch to the mini-buckle. Do not let it twist.

Safety Belts This section of the manual describes how to use safety belts properly. It also describes some things not to do with safety belts.

{ Warning

Do not let anyone ride where a safety belt cannot be worn properly. In a crash, if you or your passenger(s) are not wearing safety belts, injuries can be much worse than if you are wearing safety belts. You can be seriously injured or killed by hitting things inside the vehicle harder or by being ejected from the vehicle. In addition, anyone who is not buckled up can strike other passengers in the vehicle. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, passengers riding in these areas are more likely to be seriously injured or killed. Do not allow

(Continued)

Warning (Continued)

passengers to ride in any area of the vehicle that is not equipped with seats and safety belts. Always wear a safety belt, and check that all passenger(s) are restrained properly too.

This vehicle has indicators as a reminder to buckle the safety belts. See Safety Belt Reminders 0 110. Why Safety Belts Work

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

When riding in a vehicle, you travel as fast as the vehicle does. If the vehicle stops suddenly, you keep going until something stops you. It could be the windshield, the instrument panel, or the safety belts! When you wear a safety belt, you and the vehicle slow down together. There is more time to stop because you stop over a longer distance and, when worn properly, your strongest bones take the forces from the safety belts. That is why wearing safety belts makes such good sense. Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt?

A: You could be — whether you are

wearing a safety belt or not. Your chance of being conscious during and after a crash, so you can unbuckle and get out, is much greater if you are belted.

Q: If my vehicle has airbags, why

should I have to wear safety belts?

A: Airbags are supplemental

systems only; so they work with safety belts — not instead of them. Whether or not an airbag is provided, all occupants still have to buckle up to get the most protection. Also, in nearly all states and in all Canadian provinces, the law requires wearing safety belts.

How to Wear Safety Belts Properly This section is only for people of adult size. There are special things to know about safety belts and children. And there are different rules for smaller children and infants. If a child will be riding in the vehicle, see Older Children 0 76 or Infants and Young Children 0 77. Follow those rules for everyone's protection.

Seats and Restraints

57

It is very important for all occupants to buckle up. Statistics show that unbelted people are hurt more often in crashes than those who are wearing safety belts. There are important things to know about wearing a safety belt properly.

. Sit up straight and always keep

your feet on the floor in front of you.

. Always use the correct buckle

for your seating position.

. Wear the lap part of the belt low

and snug on the hips, just touching the thighs. In a crash, this applies force to the strong

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt. If you are using a rear seating position with a detachable safety belt and the safety belt is not attached, see “Returning the Seat to the Seating Position” under Third Row Seats 0 53 for instruction on reconnecting the safety belt to the mini-buckle. The following instructions explain how to wear a lap-shoulder belt properly. 1. Adjust the seat, if the seat is adjustable, so you can sit up straight. To see how, see “Seats” in the Index.

58

Seats and Restraints

pelvic bones and you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force on your abdomen. This could cause serious or even fatal injuries.

. Wear the shoulder belt over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces. The shoulder belt locks if there is a sudden stop or crash.

{ Warning

You can be seriously injured, or even killed, by not wearing your safety belt properly.

. Never allow the lap or

shoulder belt to become loose or twisted.

. Never wear the shoulder belt under both arms or behind your back.

. Never route the lap or shoulder belt over an armrest.

2. Pick up the latch plate and pull the belt across you. Do not let it get twisted. The lap-shoulder belt may lock if you pull the belt across you very quickly. If this happens, let the belt go back slightly to unlock it. Then pull the belt across you more slowly. If the shoulder portion of a passenger belt is pulled out all the way, the child restraint locking feature may be engaged. If this happens, let the belt go back all the way and start again.

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

Seats and Restraints

59

3. Push the latch plate into the

5. To make the lap part tight, pull

up on the shoulder belt. It may be necessary to pull the stitching on the safety belt through the latch plate to fully tighten the lap belt on smaller occupants.

buckle until it clicks. Pull up on the latch plate to make sure it is secure. If the belt is not long enough, see Safety Belt Extender 0 62. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary. If equipped with a shoulder belt height adjuster, move it to the height that is right for you. See “Shoulder Belt Height Adjuster” later in this section for instructions on use and important safety information.

4.

To unlatch the belt, push the button on the buckle. The belt should return to its stowed position. Slide the latch plate up the safety belt webbing when the safety belt is not in use. The latch plate should rest on the stitching on the safety belt, near the guide loop on the side wall. Always stow the safety belt slowly. If the safety belt webbing returns quickly to the stowed position, the retractor may lock and cannot be pulled out. If this happens, pull the safety belt straight out firmly to unlock the webbing, and then release it. If the webbing is still locked in the retractor, see your dealer.

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

60

Seats and Restraints

Before a door is closed, be sure the safety belt is out of the way. If a door is slammed against a safety belt, damage can occur to both the safety belt and the vehicle. Shoulder Belt Height Adjuster The vehicle has a shoulder belt height adjuster for the driver and front outboard passenger seating positions. Adjust the height so the shoulder portion of the belt is on the shoulder but not falling off of it. The belt should be close to but not contacting the neck. Improper shoulder belt height adjustment could reduce the effectiveness of the safety belt in a crash. See How to Wear Safety Belts Properly 0 57.

are part of the safety belt assembly. They can help tighten the safety belts during the early stages of a moderate to severe frontal, near frontal, or rear crash if the threshold conditions for pretensioner activation are met. Safety belt pretensioners can also help tighten the safety belts in a side crash or a rollover event. Pretensioners work only once. If the pretensioners activate in a crash, they will need to be replaced, and the vehicle’s safety belt system will probably need other new parts. See Replacing Safety Belt System Parts after a Crash 0 63. Rear Safety Belt Comfort Guides

{ Warning

A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder

(Continued)

To move it down, push down on the release button and move the height adjuster to the desired position. You can move the height adjuster up by pushing up on the shoulder belt guide. After the adjuster is set to the desired position, try to move it down without pushing the release button to make sure it has locked into position. Safety Belt Pretensioners This vehicle has safety belt pretensioners for the front outboard occupants. Although the safety belt pretensioners cannot be seen, they

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

Seats and Restraints

61

2. Place the guide over the belt,

and insert the two edges of the belt into the slots of the guide.

1. Remove the guide from its

storage clip on the interior trim next to the outboard seatback.

3. Be sure that the belt is not twisted and it lies flat. The elastic cord must be behind the belt with the plastic guide on the front.

Warning (Continued)

belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces.

Rear safety belt comfort guides may provide added safety belt comfort for older children who have outgrown booster seats and for some adults. When installed on a shoulder belt, the comfort guide positions the shoulder belt away from the neck and head.

Second Row Outboard Seating Positions The vehicle has comfort guides for the second row outboard seating positions. The comfort guides are stored on a clip on the interior trim next to the outboard seatback. To install:

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

62

Seats and Restraints

Third Row Seating Positions Comfort guides are available through your dealer for the third row seating positions. Instructions are included with the guide.

Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts.

A pregnant woman should wear a lap-shoulder belt, and the lap portion should be worn as low as possible, below the rounding, throughout the pregnancy. The best way to protect the fetus is to protect the mother. When a safety belt is worn properly, it is more likely that the fetus will not be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly.

Safety Belt Extender If the vehicle's safety belt will fasten around you, you should use it. But if a safety belt is not long enough, your dealer will order you an extender. When you go in to order it, take the heaviest coat you will wear, so the extender will be long enough for you. To help avoid personal injury, do not let someone else use it, and use it only for the seat it is made to fit. The extender has been designed for adults. Never use it for securing child seats. To wear it, attach it to the regular safety

4. Buckle, position, and release

the safety belt as described previously in this section. Make sure the shoulder portion of the belt is on the shoulder and not falling off of it. The belt should be close to, but not contacting, the neck.

To remove and store the comfort guide, squeeze the belt edges together so that the safety belt can be removed from the guide. Slide the guide onto its storage clip.

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

belt. For more information, see the instruction sheet that comes with the extender.

Safety System Check Now and then, check that the safety belt reminder light, safety belts, buckles, latch plates, retractors, and anchorages are all working properly. Look for any other loose or damaged safety belt system parts that might keep a safety belt system from doing its job. See your dealer to have it repaired. Torn or frayed safety belts may not protect you in a crash. They can rip apart under impact forces. If a belt is torn or frayed, get a new one right away. Make sure the safety belt reminder light is working. See Safety Belt Reminders 0 110. Keep safety belts clean and dry. See Safety Belt Care 0 63.

Safety Belt Care Keep belts clean and dry. { Warning

Do not bleach or dye safety belts. It may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.

Replacing Safety Belt System Parts after a Crash

{ Warning

A crash can damage the safety belt system in the vehicle. A damaged safety belt system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure the safety belt systems are working

(Continued)

Seats and Restraints

63

Warning (Continued)

properly after a crash, have them inspected and any necessary replacements made as soon as possible.

After a minor crash, replacement of safety belts may not be necessary. But the safety belt assemblies that were used during any crash may have been stressed or damaged. See your dealer to have the safety belt assemblies inspected or replaced. New parts and repairs may be necessary even if the safety belt system was not being used at the time of the crash. Have the safety belt pretensioners checked if the vehicle has been in a crash, or if the airbag readiness light stays on after you start the vehicle or while you are driving. See Airbag Readiness Light 0 111.

Buick Enclave Owner Manual 9159225) - 2016 - CRC - 4/24/15

(GMNA-Localizing-U.S./Canada/Mexico-

64

Seats and Restraints

Airbag System The vehicle has the following airbags: . A frontal airbag for the driver. . A frontal airbag for the front

outboard passenger.

. A front center airbag for the

driver and front outboard passenger.

. A seat-mounted side impact

airbag for the driver.

. A seat-mounted side impact airbag for the front outboard passenger.

. A roof-rail airbag for the driver

and for the second and third row passengers seated directly behind the driver.

. A roof-rail airbag for the front outboard passenger and the second and third row passengers seated directly behind the front outboard passenger.

All vehicle airbags have the word AIRBAG on the trim or on an attached label near the deployment