2013 Buick Enclave Owners Manual

10-second pre-alarm occurs. The

horn chirps and the lights flash. If the key is not placed in the ignition and turned to START or the door is not unlocked by pressing Q during the 10-second pre-alarm, the alarm goes off. The headlamps flash and the horn sounds for about 30 seconds, then turns off to save the battery power. The vehicle can be started with the correct ignition key if the alarm has been set off. To avoid setting off the alarm by accident:

Lock the vehicle with the door key after the doors are closed. . Unlock the door with the RKE

transmitter. Unlocking a door any other way sets off the alarm if the system has been armed. Press K or place the key in the ignition and turn it to START to turn off the alarm.

Testing the Alarm To test the alarm: 1. From inside the vehicle, lower

the driver side window, and open the driver door.

2. Press Q. 3. Get out of the vehicle, close the

door, and wait for the security light to go out.

4. Reach in through the window,

unlock the door with the manual door lock, and open the door. This should set off the alarm.

If the alarm does not sound when it should, but the headlamps flash, check to see if the horn works. The horn fuse may be blown. To replace the fuse, see Fuses and Circuit Breakers on page 10‑28. If the alarm does not sound or the headlamps do not flash, see your dealer for service.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (13,1)

Keys, Doors, and Windows

2-13

Immobilizer See Radio Frequency Statement on page 13‑20 for information regarding Part 15 of the Federal Communications Commission (FCC) rules and Industry Canada Standards RSS-GEN/210/220/310.

Immobilizer Operation This vehicle has PASS-Key® III+ (Personalized Automotive Security System) theft-deterrent system. PASS-Key III+ is a passive theft-deterrent system. The system is automatically armed when the key is removed from the ignition. The system is automatically disarmed when the key is turned to ON/RUN, ACC/ACCESSORY, or START from the LOCK/OFF position. You do not have to manually arm or disarm the system.

The security light comes on if there is a problem with arming or disarming the theft-deterrent system. When the PASS-Key III+ system senses an incorrect key, the vehicle does not start. Anyone using a trial-and-error method to start the vehicle will be discouraged because of the high number of electrical key codes. If the engine does not start and the security light on the instrument panel comes on when trying to start the vehicle, there may be a problem with the theft-deterrent system. Turn the ignition off and try again. If the engine still does not start, and the key appears to be undamaged, try another ignition key and check the fuses. See Fuses and Circuit Breakers on page 10‑28 for additional information. If the engine still does not start with the other key,

the vehicle needs service. If the vehicle does start, the first key may be faulty. See your dealer who can service the PASS-Key III+ to have a new key made. In an emergency, contact Roadside Assistance. See Roadside Assistance Program (Mexico) on page 13‑7 or Roadside Assistance Program (U.S. and Canada) on page 13‑11. It is possible for the PASS-Key III+ decoder to learn the transponder value of a new or replacement key. Up to 10 keys may be programmed to the vehicle. The following procedure is for programming additional keys only. If all currently programmed keys are lost or do not operate, you must see your dealer or a locksmith who can service PASS-Key III+ to have keys made and programmed to the system. See your dealer or a locksmith who can service PASS-Key III+ to get a new key blank that is cut exactly as the ignition key that operates the system.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (14,1)

2-14

Keys, Doors, and Windows

To program the new additional key:

1. Verify that the new key has a 1

2.

stamped on it. Insert the already programmed key in the ignition and start the engine. If the engine does not start, see your dealer for service. 3. After the engine has started, turn

4.

the key to LOCK/OFF, and remove the key. Insert the key to be programmed and turn it to the ON/RUN position within five seconds of the original key being turned to the LOCK/OFF position. The security light turns off once the key has been programmed.

5. Repeat Steps 1–4 if additional

keys are to be programmed.

If the PASS-Key III+ key is lost or damaged, see your dealer or a locksmith to have a new key made. The SERVICE THEFT DETERRENT SYSTEM message displays on the Driver Information Center (DIC) when there is a problem with the theft-deterrent system. See Security Messages on page 5‑34 for additional information. Do not leave the key or device that disarms or deactivates the theft-deterrent system in the vehicle.

Exterior Mirrors

Convex Mirrors

{ WARNING

A convex mirror can make things, like other vehicles, look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on the right. Check the inside mirror or glance over your shoulder before changing lanes.

The passenger side mirror is convex shaped. A convex mirror's surface is curved so more can be seen from the driver seat.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (15,1)

Power Mirrors

To adjust each mirror: 1. Press (1) or (2) to select the

mirror.

2. Press on the control pad to

adjust the mirror.

3. Press (1) or (2) again to deselect

the mirror.

Keys, Doors, and Windows

2-15

Side Blind Zone Alert (SBZA) If the vehicle has the Side Blind Zone Alert (SBZA) system. See Side Blind Zone Alert (SBZA) on page 9‑32 for more information.

Folding Mirrors For vehicles with manual folding mirrors, push the mirror toward the vehicle. Pull the mirror out to return to its original position. For vehicles with outside power foldaway mirrors:

1. Press (1) to fold the mirrors out

to the driving position.

2. Press (2) to fold the mirrors in to

the folded position.

Resetting the Power Foldaway Mirrors Reset the power foldaway mirrors if:

The mirrors are accidentally obstructed while folding. They are accidentally manually folded/unfolded. The mirrors vibrate at normal driving speeds.

Fold and unfold the mirrors one time using the mirror controls to reset them to their normal position. A popping noise may be heard during the resetting of the power foldaway mirrors. This sound is normal after a manual folding operation.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (16,1)

2-16

Keys, Doors, and Windows

Heated Mirrors For vehicles with heated mirrors: 1 (Rear Window Defogger): Press to heat the mirrors. See “Rear Window Defogger” under Dual Automatic Climate Control System on page 8‑1.

Automatic Dimming Mirror If the vehicle has the automatic dimming mirror, the driver outside mirror automatically adjusts for the glare of the headlamps from behind. This feature is controlled by the on and off setting on the inside rearview mirror. See Automatic Dimming Rearview Mirror on page 2‑16.

Park Tilt Mirrors If the vehicle has the memory package, the outside mirrors have a park tilt feature. This feature tilts the outside mirrors to a preselected position when the vehicle is in R (Reverse). This allows the driver to view the curb for parallel parking. The passenger and/or driver mirror returns to its original position when the vehicle is shifted out of R (Reverse), or the ignition is turned off or to OFF/LOCK. This feature can be turned on or off through the Driver Information Center (DIC). See Vehicle Personalization on page 5‑37 for more information.

Interior Mirrors

Automatic Dimming Rearview Mirror Adjust the rearview mirror to clearly view the area behind the vehicle. The mirror will automatically reduce the glare from the headlamps from behind. The dimming feature and the indicator light come on when the vehicle is started. There may be an on and off setting on the mirror. O (On/Off): Press to turn the dimming feature on or off. Vehicles with OnStar have three additional control buttons for the OnStar system. See your dealer for more information about OnStar and how to subscribe to it. See OnStar Overview on page 14‑1. Cleaning the Mirror Do not spray glass cleaner directly on the mirror. Use a soft towel dampened with water.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (17,1)

Keys, Doors, and Windows

2-17

Windows

{ WARNING

Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke.

The vehicle aerodynamics are designed to improve fuel economy performance. This may result in a pulsing sound when either rear window is down and the front windows are up. To reduce the sound, open either a front window or the sunroof, if equipped.

Power Windows

{ WARNING Children could be seriously injured or killed if caught in the path of a closing window. Never leave keys in a vehicle with children. When there are children in the rear seat, use the window lockout button to prevent operation of the windows. See Keys on page 2‑1.

Uplevel Shown, Base Similar The driver door also has switches that control the passenger and rear windows. The power windows work with the ignition in ACC/ ACCESSORY, ON/RUN or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 9‑18. Press the switch to lower the window. Pull up on the front edge of the switch to raise the window.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (18,1)

2-18

Keys, Doors, and Windows

Express-Up/Express-Down Windows A window with the express-up/down feature allows it to be raised or lowered without holding the switch. Press or pull the window switch fully and release it to activate the express feature. The express mode can be canceled by pressing or pulling the switch. Programming the Power Windows If the battery on the vehicle has been recharged, disconnected, or replaced, windows with the express-up feature need to be reprogrammed for this feature to work. To program the window: 1. Close all doors with the ignition in the ACC/ACCESSORY, ON/ RUN position, or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 9‑18.

2. Press and continue to hold the window switch until the window is fully open.

3. Pull up and hold the window switch to close the window. Continue to hold it briefly after the window is fully closed.

4. Repeat for each window that has

the express-up feature.

Anti-Pinch Feature The anti-pinch feature is on windows with the express-up feature. If an object is in the way of the window as it is express-closing, or in certain weather conditions like severe icing, the window will stop and open to a factory preset position. The window functions normally once the obstruction is removed.

Rear Window Lockout

The rear window lockout feature prevents the rear passenger windows from operating, except from the driver position. Press v to activate the rear window lockout switch. The indicator light comes on when activated. Press v again to deactivate the lockout switch.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (19,1)

Sun Visors

Roof

Keys, Doors, and Windows

2-19

Sunroof The ignition must be in ON/RUN, ACC/ACCESSORY, or Retained Accessory Power (RAP) must be active to operate the sunroof and power sunshade. See Retained Accessory Power (RAP) on page 9‑18. The vehicle may have a sunroof over the front seats and a rear sunroof over the second row seats. The rear sunroof does not open.

Pull the sun visor down to block glare. If equipped, detach the sun visor from the center mount to pivot to the side window or to extend along the rod.

Vent: From the closed position, press and hold the front of the switch to vent the sunroof. Press and hold the rear of the switch to close the sunroof. Express-open/Express-close: From the closed position, press and release the rear of the switch to express-open the sunroof. Press and release the front of the switch to express-close the sunroof.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (20,1)

2-20

Keys, Doors, and Windows

Manual Sunshade The sunshades must be opened and closed manually. To open the sunshade, press the button on the sunshade handle to release it and guide it back. To close the sunshade, pull the sunshade forward until it latches.

Periodically open the sunroof and remove any obstacles or loose debris. Wipe the sunroof seal and roof sealing area using a clean cloth, mild soap, and water. Do not remove grease from the sunroof.

Dirt and debris may collect on the sunroof seal or in the track. This could cause an issue with sunroof operation or noise. It could also plug the water drainage system.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (1,1)

Seats and Restraints

3-1

Seats and Restraints

Head Restraints

Head Restraints . . . . . . . . . . . . . . . 3-2

Front Seats

Power Seat Adjustment . . . . . . . 3-3
Lumbar Adjustment . . . . . . . . . . . 3-4
Reclining Seatbacks . . . . . . . . . . 3-4
Memory Seats . . . . . . . . . . . . . . . . 3-5
Heated and Ventilated Front

Seats . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Rear Seats

Rear Seats . . . . . . . . . . . . . . . . . . . . 3-8
Third Row Seats . . . . . . . . . . . . . 3-10

Safety Belts

Safety Belts . . . . . . . . . . . . . . . . . . 3-13
How to Wear Safety Belts

Properly . . . . . . . . . . . . . . . . . . . . 3-14

Lap-Shoulder Belt . . . . . . . . . . . 3-15
Safety Belt Use During

Pregnancy . . . . . . . . . . . . . . . . . . 3-20
Safety Belt Extender . . . . . . . . . 3-20
Safety System Check . . . . . . . . 3-20
Safety Belt Care . . . . . . . . . . . . . 3-21
Replacing Safety Belt System

Parts after a Crash . . . . . . . . . 3-21

Airbag System

Airbag System . . . . . . . . . . . . . . . 3-22
Where Are the Airbags? . . . . . 3-24
When Should an Airbag

Inflate? . . . . . . . . . . . . . . . . . . . . . 3-26

What Makes an Airbag

Inflate? . . . . . . . . . . . . . . . . . . . . . 3-27

How Does an Airbag

Servicing the Airbag-Equipped

Vehicle . . . . . . . . . . . . . . . . . . . . . 3-33

Adding Equipment to the

Airbag-Equipped Vehicle . . . 3-33
Airbag System Check . . . . . . . . 3-34
Replacing Airbag System

Parts after a Crash . . . . . . . . . 3-35

Child Restraints

Older Children . . . . . . . . . . . . . . . 3-35
Infants and Young

Children . . . . . . . . . . . . . . . . . . . . 3-37
Child Restraint Systems . . . . . 3-40
Where to Put the Restraint . . . 3-41
Lower Anchors and Tethers

for Children (LATCH System) . . . . . . . . . . . . . . . . . . . . 3-43

Restrain? . . . . . . . . . . . . . . . . . . . 3-27

Replacing LATCH System

What Will You See after an

Parts After a Crash . . . . . . . . . 3-50

Airbag Inflates? . . . . . . . . . . . . 3-27

Securing Child Restraints

Passenger Sensing

(Rear Seat) . . . . . . . . . . . . . . . . . 3-50

System . . . . . . . . . . . . . . . . . . . . . 3-29

Securing Child Restraints

(Front Passenger Seat) . . . . 3-52

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (2,1)

3-2

Seats and Restraints

Head Restraints

Front Seats

{ WARNING

With head restraints that are not installed and adjusted properly, there is a greater chance that occupants will suffer a neck/ spinal injury in a crash. Do not drive until the head restraints for all occupants are installed and adjusted properly.

The vehicle's front seats have adjustable head restraints in the outboard seating positions.

Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant's head. This position reduces the chance of a neck injury in a crash.

To raise or lower the head restraint, press the button located on the side of the head restraint, and pull up or push the head restraint down, and release the button. Pull and push on the head restraint after the button is released to make sure that it is locked in place. To adjust the head restraint forward, grasp the head restraint and pull forward until the desired locking position is reached.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (3,1)

To adjust the head restraint rearward, press the button located on the side of the head restraint, and push the head restraint rearward until the desired locking position is reached. Try to move the head restraint after the button is released to make sure that it is locked in place. The front seat outboard head restraints are not designed to be removed. Rear Seats The vehicle's second-row seats have head restraints in the outboard seating positions that cannot be adjusted. The vehicle's third-row seats have headrests in the outboard seating positions that cannot be adjusted. The second-row head restraints and third-row headrests are not designed to be removed.

Front Seats

Power Seat Adjustment

{ WARNING You can lose control of the vehicle if you try to adjust a driver seat while the vehicle is moving. Adjust the driver seat only when the vehicle is not moving.

1. Seat Adjustment Control 2. Reclining Seatback Control

Seats and Restraints

3-3

3. Lumbar Adjustment Control To adjust the seat: . Move the seat forward or

rearward by sliding the control (1) forward or rearward. . Raise or lower the front part of the seat cushion by moving the front of the control (1) up or down.

. Raise or lower the entire seat by moving the rear of the control (1) up or down.

. Adjust the seatback by tilting the

top of the control (2) forward or rearward. See Reclining Seatbacks on page 3‑4. Increase or decrease lumbar support by pressing the front or rear of the control (3). See Lumbar Adjustment on page 3‑4.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (4,1)

3-4

Seats and Restraints

Lumbar Adjustment

Power Lumbar

Manual Lumbar

Reclining Seatbacks

Power Reclining Seatbacks

If available, move the handle forward or rearward to increase or decrease lumbar support.

If available, press and hold the front or rear of control to increase or decrease lumbar support. Release the control when the seatback reaches the desired level of lumbar support.

To adjust the seatback:

Tilt the top of the control rearward to recline. Tilt the top of the control forward to raise.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (5,1)

Seats and Restraints

3-5

Memory Seats

Do not have a seatback reclined if the vehicle is moving.

If available, the controls on the driver door are used to program and recall memory settings for the driver seat, outside mirrors, and power steering column (if equipped).

{ WARNING

Sitting in a reclined position when the vehicle is in motion can be dangerous. Even when buckled up, the safety belts cannot do their job. The shoulder belt will not be against your body. Instead, it will be in front of you. In a crash, you could go into it, receiving neck or other injuries. The lap belt could go up over your abdomen. The belt forces would be there, not at your pelvic bones. This could cause serious internal injuries. For proper protection when the vehicle is in motion, have the seatback upright. Then sit well back in the seat and wear the safety belt properly.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (6,1)

3-6

Seats and Restraints

Storing Memory Positions To save into memory: 1. Adjust the driver seat and

seatback recliner, both outside mirrors, and the power steering column (if equipped). Not all vehicles will have the ability to save and recall the mirror positions.

2. Press and hold “1” until

two beeps sound.

3. Repeat for a second driver

position using “2.”

To recall, press and release “1” or “2.” The vehicle must be in P (Park). A single beep will sound. The seat, outside mirrors, and power steering column (if equipped) will move to the positions previously stored for the identified driver.

Memory Remote Recall The memory feature can recall the driver seat, outside mirrors, and power steering column (if equipped) to stored positions when entering the vehicle. To activate, unlock the driver door with the Remote Keyless Entry (RKE) transmitter. The driver seat, outside mirrors, and power steering column will move to the memory positions associated with the transmitter used to unlock the vehicle. This feature is turned on or off using the vehicle personalization menu. See Vehicle Personalization on page 5‑37. To stop recall movement, press one of the power seat controls, memory buttons, power mirror buttons, or the power steering column control (if equipped).

If something has blocked the driver seat and/or steering column while recalling a memory position, the recall may stop. Remove the obstruction; then press and hold the appropriate manual control for the memory item that is not recalling for two seconds. Try recalling the memory position again by pressing the appropriate memory button. If the memory position is still not recalling, see your dealer for service.

Easy Exit Positions The easy exit feature can move the driver seat rearward and the power steering column (if equipped) up and forward to allow extra room to exit the vehicle. S (Easy Exit Positions): Press to activate the recall. The vehicle must be in P (Park). If this feature is programmed on in the vehicle personalization menu, automatic driver seat and power steering column movement occur when the ignition key is removed.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (7,1)

A single beep sounds. The driver seat moves back approximately 8 cm (3 in) and the power steering column (if equipped) moves up and forward. To move the seat back farther, press S again until the seat is all the way back. If something has blocked the driver seat while recalling the exit position, the recall may stop. Remove the obstruction; then press and hold the power seat control rearward for two seconds. Try recalling the exit position again. If the exit position is still not recalling, see your dealer for service. See Vehicle Personalization on page 5‑37.

Heated and Ventilated Front Seats

{ WARNING

If you cannot feel temperature change or pain to the skin, the seat heater may cause burns. To reduce the risk of burns, people with such a condition should use care when using the seat heater, especially for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket, cushion, cover, or similar item. This may cause the seat heater to overheat. An overheated seat heater may cause a burn or may damage the seat.

Seats and Restraints

3-7

Heated and Cooled Seat Buttons

Shown, Heated Seat Buttons

Similar

If available,

If available, the buttons are on the center console. To operate, the engine must be running. I (Heated Seatback): press to heat the seatback only. H (Cooled Seat): If available, press to cool the entire seat. J (Heated Seat and Seatback): Press to heat the seat and seatback. Press the button once for the highest setting. With each press of the button, the seat will change to the next lower setting, and then to

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (8,1)

3-8

Seats and Restraints

the off setting. The lights indicate three for the highest setting and one for the lowest. The passenger heated seat may take longer to heat up. The heated and/or cooled seats are canceled after the ignition is turned off.

Remote Start Heated Seats When it is cold outside, the heated seats may turn on automatically during a remote vehicle start. The heated seats will be canceled when the ignition is turned on. Press the desired heated seat button to use the heated seats after the vehicle is started. The heated seat button lights will not turn on during a remote start. The temperature of an unoccupied seat may be reduced. See Remote Vehicle Start on page 2‑4.

Rear Seats

1. Seat Adjustment Handle 2. Reclining Seatback Strap 3. Sliding Seat Lever

Entering and Exiting the Third Row

{ WARNING Using the third row seating position while the second row is folded, or folded and tumbled, could cause injury in a sudden stop or crash. Be sure to return the seat to the passenger seating position. Push and pull on the seat to make sure it is locked into place.

Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts. Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (9,1)

5. Pull the sliding seat lever (3) forward. The seatback will tilt forward, and the seat will begin sliding forward. Continue to push forward on the seatback until the entire seat moves all the way forward and the seat cushion is folded.

Returning the Seat to the Seating Position To return the second row seat to its normal seating position: 1. Remove objects on the floor

behind the second row seat or in the seat tracks on the floor. 2. Slide the seat rearward by

pushing on the seatback until the seat is locked into place.

3. Continue pushing the seatback

rearward until the seatback is locked into place.

4. Push down on the rear of the

seat cushion until it is locked in place.

Seats and Restraints

3-9

5. Push and pull on the seatback and seat cushion to make sure they are locked in place.

6. Check that the safety belt is not

under the seat cushion. Reclining the Seatbacks To recline the seatback: 1. Leaning rearward in the seat,

pull the reclining seatback strap (2).

2. Move the seatback to the desired position, and then release the strap (2) to lock the seatback in place.

3. Push and pull on the seatback to

make sure it is locked. Folding the Seatback To fold the second row seatbacks: 1. Remove anything on or under

the seat.

2. Place the armrest in the upright

position, and unfasten the safety belt.

To access the third row: 1. Remove objects on the floor in

front of or on the second row seat, or in the seat tracks on the floor.

2. Move the front center console

armrest completely forward. See Center Console Storage on page 4‑2.

3. Place the folding armrests in the

upright position.

4. Make sure that the safety belt is

unfastened and in the stowed position.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (10,1)

3-10

Seats and Restraints

3. Pull forward on the reclining

seatback strap (2). The head restraint will fold down automatically.

To return the seatback to the seating position, lift the seatback and push it rearward until it locks into place. Push and pull on the seatback to make sure it is locked. Pull up on the head restraint to return it to the upright, locked position. Adjusting the Seats To adjust the second row seats, pull outward on the seat adjustment handle (1). Slide the seat forward or rearward to the desired position. Release the handle (1), and push and pull on the seat to make sure it is locked.

Third Row Seats

{ WARNING Using the third row seating position while the second row is folded, or pushed forward in the entry position, could cause injury in a sudden stop or crash. Be sure to return the seat to the passenger seating position. Push and pull on the seat to make sure it is locked into place.

Folding the Seatback Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts. Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat.

To fold the third row seatback: 1. Remove anything on or under

the seat.

2. Disconnect the rear safety belt

mini-latch, using a key in the slot on the mini-buckle, and let the belt retract into the headliner. Stow the mini-latch in the holder in the headliner.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (11,1)

Seats and Restraints

3-11

or lift the seatback and push it into place from inside the vehicle.

2. The headrest must be locked

into place before sitting in the seat.

{ WARNING

If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they are locked.

3. Push and pull on the seatback to

make sure it is locked in place.

{ WARNING

A safety belt that is improperly routed, not properly attached, or twisted will not provide the

WARNING (Continued)

protection needed in a crash. The person wearing the belt could be seriously injured. After raising the rear seatback, always check to be sure that the safety belts are properly routed and attached, and are not twisted.

4. Reconnect the center safety belt mini-latch to the mini-buckle. Do not let it twist.

5. Pull on the safety belt to be sure

the mini-latch is secure.

Removing the Third Row Seats To remove a third row seat: 1. Remove the cargo management

system, if available and installed. See Cargo Management System on page 4‑3.

2. Remove anything on or under

(Continued)

the seat.

3. Pull up on the release lever on

the back of the seat. The headrest moves forward automatically.

4. Push the seatback forward to

lay flat.

Returning the Seat to the Seating Position To return the seatback to the seating position: 1. From the rear of the vehicle,

raise the seatback to the upright position using the pullstrap on the back of the third row seat,

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (12,1)

3-12

Seats and Restraints

Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts. Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat. 3. Fold the seatback down. See

“Folding the Seatback” earlier in this section.

4. Remove the rear bolts on the floor on each side of the seat.

5. Remove the seat by tilting it

slightly upward, and then pulling it out of the rear of the vehicle in one motion.

6. Replace the bolts in the floor

holes for storage.

Installing the Third Row Seats To reinstall a third row seat: 1. Before installing the seat the

seatback must be folded forward. See “Folding the Seatback” earlier in this section. The seats must be placed in the proper locations to attach correctly. The wider seat must be installed on the driver side and the narrower seat on the passenger side. Remove the bolts from the holes in the floor before installing the seats.

2. Place the seat on the vehicle

floor so that the front seat hooks are on the vehicle bars.

3. Reinstall the bolts, and torque to

55 Y (41 lb ft). Pull up on the seat to make sure it is locked in place.

4. Raise the seatback to its upright

position. Push and pull on the seatback to make sure it is locked into place.

5. Push the headrest up into

position. Push and pull on the headrest to make sure it is locked into place.

6. Reconnect the center safety belt mini-latch to the mini-buckle. Do not let it twist.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (13,1)

Safety Belts This section of the manual describes how to use safety belts properly. It also describes some things not to do with safety belts.

{ WARNING

Do not let anyone ride where a safety belt cannot be worn properly. In a crash, if you or your passenger(s) are not wearing safety belts, injuries can be much worse than if you are wearing safety belts. You can be seriously injured or killed by hitting things inside the vehicle harder or by being ejected from the vehicle. In addition, anyone who is not buckled up can strike other passengers in the vehicle.

(Continued)

Seats and Restraints

3-13

WARNING (Continued)

Why Safety Belts Work

It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, passengers riding in these areas are more likely to be seriously injured or killed. Do not allow passengers to ride in any area of the vehicle that is not equipped with seats and safety belts. Always wear a safety belt, and check that all passenger(s) are restrained properly too.

This vehicle has indicators as a reminder to buckle the safety belts. See Safety Belt Reminders on page 5‑13.

When riding in a vehicle, you travel as fast as the vehicle does. If the vehicle stops suddenly, you keep going until something stops you. It could be the windshield, the instrument panel, or the safety belts! When you wear a safety belt, you and the vehicle slow down together. There is more time to stop because you stop over a longer distance and, when worn properly, your strongest bones take the forces from the

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (14,1)

3-14

Seats and Restraints

safety belts. That is why wearing safety belts makes such good sense. Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt?

A: You could be — whether you are

wearing a safety belt or not. Your chance of being conscious during and after a crash, so you can unbuckle and get out, is much greater if you are belted.

Q: If my vehicle has airbags, why

should I have to wear safety belts?

A: Airbags are supplemental

systems only; so they work with safety belts — not instead of them. Whether or not an airbag is provided, all occupants still have to buckle up to get the most protection.

Also, in nearly all states and in all Canadian provinces, the law requires wearing safety belts.

How to Wear Safety Belts Properly This section is only for people of adult size. There are special things to know about safety belts and children. And there are different rules for smaller children and infants. If a child will be riding in the vehicle, see Older Children on page 3‑35 or Infants and Young Children on page 3‑37. Follow those rules for everyone's protection. It is very important for all occupants to buckle up. Statistics show that unbelted people are hurt more often in crashes than those who are wearing safety belts. There are important things to know about wearing a safety belt properly.

. Sit up straight and always keep

your feet on the floor in front of you.

. Always use the correct buckle

for your seating position.

. Wear the lap part of the belt low

and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones and you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force on your abdomen. This could cause serious or even fatal injuries.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (15,1)

Seats and Restraints

3-15

. Wear the shoulder belt over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces. The shoulder belt locks if there is a sudden stop or crash.

{ WARNING

You can be seriously injured, or even killed, by not wearing your safety belt properly. . Never allow the lap or

shoulder belt to become loose or twisted.

. Never wear the shoulder belt

under both arms or behind your back.

. Never route the lap or shoulder belt over an armrest.

Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt. If you are using a rear seating position with a detachable safety belt and the safety belt is not attached, see “Returning the Seat to the Seating Position” under Third Row Seats on page 3‑10 for instruction on reconnecting the safety belt to the mini-buckle. The following instructions explain how to wear a lap-shoulder belt properly. 1. Adjust the seat, if the seat is adjustable, so you can sit up straight. To see how, see “Seats” in the Index.

2. Pick up the latch plate and pull the belt across you. Do not let it get twisted. The lap-shoulder belt may lock if you pull the belt across you very quickly. If this happens, let the belt go back slightly to unlock it. Then pull the belt across you more slowly. If the shoulder portion of a passenger belt is pulled out all the way, the child restraint locking feature may be engaged. If this happens, let the belt go back all the way and start again.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (16,1)

3-16

Seats and Restraints

5.

If equipped with a shoulder belt height adjuster, move it to the height that is right for you. See “Shoulder Belt Height Adjuster” later in this section for instructions on use and important safety information.

3. Push the latch plate into the

buckle until it clicks.

4. Pull up on the latch plate to

make sure it is secure. If the belt is not long enough, see Safety Belt Extender on page 3‑20. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary.

To unlatch the belt, push the button on the buckle. The belt should return to its stowed position. Slide the latch plate up the safety belt webbing when the safety belt is not in use. The latch plate should rest on the stitching on the safety belt, near the guide loop on the side wall. Before a door is closed, be sure the safety belt is out of the way. If a door is slammed against a safety belt, damage can occur to both the safety belt and the vehicle.

6. To make the lap part tight, pull

up on the shoulder belt. It may be necessary to pull the stitching on the safety belt through the latch plate to fully tighten the lap belt on smaller occupants.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (17,1)

Shoulder Belt Height Adjuster The vehicle has a shoulder belt height adjuster for the driver and right front passenger seating positions. Adjust the height so the shoulder portion of the belt is on the shoulder but not falling off of it. The belt should be close to but not contacting the neck. Improper shoulder belt height adjustment could reduce the effectiveness of the safety belt in a crash. See How to Wear Safety Belts Properly on page 3‑14.

Seats and Restraints

3-17

Safety Belt Pretensioners This vehicle has safety belt pretensioners for the front outboard occupants. Although the safety belt pretensioners cannot be seen, they are part of the safety belt assembly. They can help tighten the safety belts during the early stages of a moderate to severe frontal, near frontal, or rear crash if the threshold conditions for pretensioner activation are met. And, for vehicles with side impact airbags, safety belt pretensioners can help tighten the safety belts in a side crash or a rollover event. Pretensioners work only once. If the pretensioners activate in a crash, they will need to be replaced, and probably other new parts for the vehicle's safety belt system. See Replacing Safety Belt System Parts after a Crash on page 3‑21.

To move it down, push down on the release button and move the height adjuster to the desired position. You can move the height adjuster up by pushing up on the shoulder belt guide. After the adjuster is set to the desired position, try to move it down without pushing the release button to make sure it has locked into position.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (18,1)

3-18

Seats and Restraints

Rear Safety Belt Comfort Guides This vehicle may have rear safety belt comfort guides. If not, they are available through your dealer. The guides may provide added safety belt comfort for older children who have outgrown booster seats and for some adults. When installed and properly adjusted, the comfort guide positions the shoulder belt away from the neck and head.

Here is how to install a comfort guide to the safety belt:

Outboard Positions

1. For the outboard positions,

remove the guide from its storage clip on the interior body. For the third row center position, locate the comfort guide which is located in a storage pocket, at the top of the seat, under the headrest on the driver side of the vehicle. To access the comfort guide, you will first need to move the headrest forward by pulling on the handle behind the seatback. The comfort guide will now be accessible.

Third Row Center Position

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (19,1)

Seats and Restraints

3-19

{ WARNING

A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces.

Pull the comfort guide out of its storage location and then return the headrest to its upright position.

3. Be sure that the belt is not twisted and it lies flat. The elastic cord must be under the belt and the guide on top.

2. Place the guide over the belt

and insert the two edges of the belt into the slots of the guide.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (20,1)

3-20

Seats and Restraints

4. Buckle, position, and release the

safety belt as described previously in this section. Make sure the shoulder portion of the belt is on the shoulder and not falling off of it. The belt should be close to, but not contacting, the neck.

To remove and store the comfort guide, squeeze the belt edges together so that the safety belt can be removed from the guide. Slide the guide into its storage location or on its storage clip.

Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts.

Safety Belt Extender If the vehicle's safety belt will fasten around you, you should use it. But if a safety belt is not long enough, your dealer will order you an extender. When you go in to order it, take the heaviest coat you will wear, so the extender will be long enough for you. To help avoid personal injury, do not let someone else use it, and use it only for the seat it is made to fit. The extender has been designed for adults. Never use it for securing child seats. To wear it, attach it to the regular safety belt. See the instruction sheet that comes with the extender.

Safety System Check Now and then, check that the safety belt reminder light, safety belts, buckles, latch plates, retractors, and anchorages are all working properly.

A pregnant woman should wear a lap-shoulder belt, and the lap portion should be worn as low as possible, below the rounding, throughout the pregnancy. The best way to protect the fetus is to protect the mother. When a safety belt is worn properly, it is more likely that the fetus will not be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (21,1)

Replacing Safety Belt System Parts after a Crash

{ WARNING

A crash can damage the safety belt system in the vehicle. A damaged safety belt system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure the safety belt systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible.

Seats and Restraints

3-21

After a minor crash, replacement of safety belts may not be necessary. But the safety belt assemblies that were used during any crash may have been stressed or damaged. See your dealer to have the safety belt assemblies inspected or replaced. New parts and repairs may be necessary even if the safety belt system was not being used at the time of the crash. Have the safety belt pretensioners checked if the vehicle has been in a crash, or if the airbag readiness light stays on after you start the vehicle or while you are driving. See Airbag Readiness Light on page 5‑14.

Look for any other loose or damaged safety belt system parts that might keep a safety belt system from doing its job. See your dealer to have it repaired. Torn or frayed safety belts may not protect you in a crash. They can rip apart under impact forces. If a belt is torn or frayed, get a new one right away. Make sure the safety belt reminder light is working. See Safety Belt Reminders on page 5‑13. Keep safety belts clean and dry. See Safety Belt Care on page 3‑21.

Safety Belt Care Keep belts clean and dry. { WARNING

Do not bleach or dye safety belts. It may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (22,1)

3-22

Seats and Restraints

Airbag System The vehicle has the following airbags: . A frontal airbag for the driver. . A frontal airbag for the front

outboard passenger.

. A front center airbag for the

driver and front outboard passenger.

. A seat-mounted side impact

airbag for the driver.

. A seat-mounted side impact airbag for the front outboard passenger.

. A roof-rail airbag for the driver

and for the second and third row passengers seated directly behind the driver.

. A roof-rail airbag for the front outboard passenger and the second and third row passengers seated directly behind the front outboard passenger.

All vehicle airbags have the word AIRBAG on the trim or on an attached label near the deployment opening. For frontal airbags, the word AIRBAG is on the center of the steering wheel for the driver and on the instrument panel for the front outboard passenger. For the front center airbag, the word AIRBAG is on the inboard side of the driver seatback. For seat-mounted side impact airbags, the word AIRBAG is on the side of the seatback closest to the door. For roof-rail airbags, the word AIRBAG is on the ceiling or trim. Airbags are designed to supplement the protection provided by safety belts. Even though today's airbags are also designed to help reduce the risk of injury from the force of an inflating bag, all airbags must inflate very quickly to do their job.

Here are the most important things to know about the airbag system:

{ WARNING

You can be severely injured or killed in a crash if you are not wearing your safety belt, even with airbags. Airbags are designed to work with safety belts, not replace them. Also, airbags are not designed to inflate in every crash. In some crashes safety belts are the only restraint. See When Should an Airbag Inflate? on page 3‑26. Wearing your safety belt during a crash helps reduce the chance of hitting things inside the vehicle or being ejected from it. Airbags are “supplemental restraints” to the safety belts. Everyone in the vehicle should wear a safety belt properly, whether or not there is an airbag for that person.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (23,1)

Seats and Restraints

3-23

There is an airbag readiness light on the instrument cluster, which shows the airbag symbol. The system checks the airbag electrical system for malfunctions. The light tells you if there is an electrical problem. See Airbag Readiness Light on page 5‑14 for more information.

{ WARNING

Because airbags inflate with great force and faster than the blink of an eye, anyone who is up against, or very close to any airbag when it inflates can be seriously injured or killed. Do not sit unnecessarily close to any airbag, as you would be if sitting on the edge of the seat or leaning forward. Safety belts help keep you in position before and during a crash. Always wear a safety belt, even with airbags. The driver should sit as far back as possible while still maintaining control of the vehicle. Occupants should not lean on or sleep against the front center armrest or console with a front center airbag.

(Continued)

WARNING (Continued)

Occupants should not lean on or sleep against the door or side windows in seating positions with seat-mounted side impact airbags and/or roof-rail airbags.

{ WARNING

Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Always secure children properly in the vehicle. To read how, see Older Children on page 3‑35 or Infants and Young Children on page 3‑37.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (24,1)

3-24

Seats and Restraints

Where Are the Airbags?

The driver frontal airbag is in the center of the steering wheel.

The front outboard passenger frontal airbag is in the passenger side instrument panel.

The front center airbag is in the inboard side of the driver seatback.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (25,1)

Seats and Restraints

3-25

WARNING (Continued)

that person causing severe injury or even death. The path of an inflating airbag must be kept clear. Do not put anything between an occupant and an airbag, and do not attach or put anything on the steering wheel hub or on or near any other airbag covering. Do not use seat or console accessories that block the inflation path of a seat-mounted side impact airbag or the front center airbag. Never secure anything to the roof of a vehicle with roof-rail airbags by routing a rope or tie-down through any door or window opening. If you do, the path of an inflating roof-rail airbag will be blocked.

Driver Side Shown, Passenger

Driver Side Shown, Passenger

Side Similar

Side Similar

The driver and front outboard passenger seat-mounted side impact airbags are in the side of the seatbacks closest to the door.

The roof-rail airbags for the driver, front outboard passenger, and second and third row outboard passengers are in the ceiling above the side windows.

{ WARNING If something is between an occupant and an airbag, the airbag might not inflate properly or it might force the object into

(Continued)

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (26,1)

3-26

Seats and Restraints

When Should an Airbag Inflate? The vehicle has frontal airbags, a front center airbag, seat-mounted side impact airbags, and roof-rail airbags. See Airbag System on page 3‑22. These airbags are designed to inflate if the impact exceeds the specific airbag system’s deployment threshold. Deployment thresholds are used to predict how severe a crash is likely to be in time for the airbag to inflate and help restrain the occupants. Deployment thresholds can vary with specific vehicle design. Frontal airbags are designed to inflate in moderate to severe frontal or near frontal crashes to help reduce the potential for severe injuries, mainly to the driver's or front outboard passenger's head and chest. Whether the frontal airbags will or should inflate is not based primarily on how fast the vehicle is traveling.

It depends on what is hit, the direction of the impact, and how quickly the vehicle slows down. Frontal airbags may inflate at different crash speeds depending on whether the vehicle hits an object straight on or at an angle, and whether the object is fixed or moving, rigid or deformable, narrow or wide. Frontal airbags are not intended to inflate during vehicle rollovers, rear impacts, or many side impacts. In addition, the vehicle has dual-stage frontal airbags. Dual-stage airbags adjust the restraint according to crash severity. The vehicle has electronic frontal sensors, which help the sensing system distinguish between a moderate frontal impact and a more severe frontal impact. For moderate frontal impacts, dual-stage airbags inflate at a level less than full deployment. For more severe frontal impacts, full deployment occurs.

The front center airbag, seat-mounted side impact airbags, and roof-rail airbags are intended to inflate in moderate to severe side crashes depending on the location of the impact. A seat-mounted side impact airbag is intended to inflate on the side of the vehicle that is struck. The front center airbag and both roof-rail airbags are intended to inflate when either side of the vehicle is struck. In addition, the roof-rail airbags and the front center airbag are intended to inflate when the sensing system predicts that the vehicle is about to roll over on its side. The roof-rail airbags are also intended to inflate in a severe frontal impact. The front center airbag is not intended to inflate in frontal impacts, near frontal impacts, or rear impacts. Seat-mounted side impact airbags are not intended to inflate in frontal impacts, near frontal impacts,

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (27,1)

rollovers, rear impacts, or on the non-struck side of a vehicle in a side impact. Roof-rail airbags are not intended to inflate in rear impacts. In any particular crash, no one can say whether an airbag should have inflated simply because of the vehicle damage or the repair costs.

What Makes an Airbag Inflate? In a deployment event, the sensing system sends an electrical signal triggering a release of gas from the inflator. Gas from the inflator fills the airbag causing the bag to break out of the cover. The inflator, the airbag, and related hardware are all part of the airbag module. For airbag locations, see Where Are the Airbags? on page 3‑24.

Seats and Restraints

3-27

How Does an Airbag Restrain? In moderate to severe frontal or near frontal collisions, even belted occupants can contact the steering wheel or the instrument panel. In moderate to severe side collisions, even belted occupants can contact the inside of the vehicle. Airbags supplement the protection provided by safety belts by distributing the force of the impact more evenly over the occupant's body. Rollover capable roof-rail airbags are also designed to help contain the head and chest of occupants in the outboard seating positions in the first, second, and third rows. The rollover capable roof-rail airbags are designed to help reduce the risk of full or partial ejection in rollover events, although no system can prevent all such ejections.

But airbags would not help in many types of collisions, primarily because the occupant's motion is not toward those airbags. See When Should an Airbag Inflate? on page 3‑26 for more information. Airbags should never be regarded as anything more than a supplement to safety belts.

What Will You See after an Airbag Inflates? After the frontal airbags and seat-mounted side impact airbags inflate, they quickly deflate, so quickly that some people may not even realize an airbag inflated. The front center airbag and roof-rail airbags may still be at least partially inflated for some time after they inflate. Some components of the airbag module may be hot for several minutes. For location of the airbags, see Where Are the Airbags? on page 3‑24.

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (28,1)

3-28

Seats and Restraints

The parts of the airbag that come into contact with you may be warm, but not too hot to touch. There may be some smoke and dust coming from the vents in the deflated airbags. Airbag inflation does not prevent the driver from seeing out of the windshield or being able to steer the vehicle, nor does it prevent people from leaving the vehicle.

{ WARNING

When an airbag inflates, there may be dust in the air. This dust could cause breathing problems for people with a history of asthma or other breathing trouble. To avoid this, everyone in the vehicle should get out as soon as it is safe to do so. If you have breathing problems but cannot get out of the vehicle after an airbag inflates, then get fresh air by opening a window or a door. If you experience breathing

WARNING (Continued)

WARNING (Continued)

problems following an airbag deployment, you should seek medical attention.

The vehicle has a feature that may automatically unlock the doors, turn on the interior lamps and hazard warning flashers, and shut off the fuel system after the airbags inflate. You can lock the doors, and turn off the interior lamps and hazard warning flashers by using the controls for those features. { WARNING

A crash severe enough to inflate the airbags may have also damaged important functions in the vehicle, such as the fuel system, brake and steering systems, etc. Even if the vehicle appears to be drivable after a

moderate crash, there may be concealed damage that could make it difficult to safely operate the vehicle. Use caution if you should attempt to restart the engine after a crash has occurred.

In many crashes severe enough to inflate the airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the front outboard passenger airbag. . Airbags are designed to inflate

only once. After an airbag inflates, you will need some new parts for the airbag system. If you do not get them, the airbag system will not be there to help protect you in another crash. A new system will include airbag modules and possibly

(Continued)

(Continued)

Buick Enclave Owner Manual - 2013 - crc - 11/14/12

Black plate (29,1)

other parts. The service manual for the vehicle covers the need to replace other parts. The vehicle has a crash sensing and diagnostic module which records information after a crash. See Vehicle Data Recording and Privacy on page 13‑19 and Event Data Recorders on page 13‑19. Let only qualified technicians work on the airbag systems. Improper service can mean that an airbag system will not work properly. See your dealer for service.

Passenger Sensing System