Notice: This vehicle has a specific coolant fill procedure. Failure to follow this procedure could cause the engine to overheat and be severely damaged. If coolant is needed, add the proper DEX-COOL coolant mixture at the coolant recovery tank.
Steam and scalding liquids from a hot cooling system can blow out and burn you badly. Never turn the cap when the cooling system, including the surge tank pressure cap, is hot. Wait for the cooling system and surge tank pressure cap to cool.
If coolant is needed, add the proper mixture directly to the radiator, but be sure the cooling system is cool before this is done.
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (15,1)
Vehicle Care
10-15
1. Detach the fasteners and lift off
the panel that covers the radiator cap.
2. Remove the radiator pressure cap when the cooling system, including the upper radiator hose, is no longer hot. Turn the pressure cap slowly counterclockwise about one full turn. If a hiss is heard, wait for that to stop. A hiss means there is still some pressure left in the system.
3. Keep turning the pressure cap
slowly and remove it.
4. Fill the radiator to the base of the filler neck with the proper DEX-COOL coolant mixture.
5. Fill the coolant recovery tank to
the FULL COLD mark.
6. Reinstall the cap on the coolant
recovery tank but leave the radiator pressure cap off.
7. Start the engine and let it run until the upper radiator hose feels warm. Any time during this procedure, watch out for the engine cooling fans.
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (16,1)
10-16
Vehicle Care
8.
If the coolant level inside the radiator filler neck is low, add more of the proper DEX-COOL coolant mixture through the filler neck until the level is back up to the base of the filler neck.
9. Replace the pressure cap tightly.
At any time during this procedure if coolant begins to flow out of the filler neck, reinstall the pressure cap.
Notice: If the pressure cap is not tightly installed, coolant loss and possible engine damage may occur. Be sure the cap is properly and tightly secured.
Engine Overheating The vehicle has several indicators to warn of engine overheating. There is an engine coolant temperature gauge on the instrument panel cluster. See Engine Coolant Temperature Gauge on page 5‑12.
The vehicle may also display an ENGINE OVERHEATED IDLE ENGINE and ENGINE OVERHEATED STOP ENGINE message in the Driver Information Center (DIC). See Engine Cooling System Messages on page 5‑29. You may decide not to lift the hood when this warning appears, but instead get service help right away. See Roadside Assistance Program (Mexico) on page 13‑7 or Roadside Assistance Program (U.S. and Canada) on page 13‑11. If you do decide to lift the hood, make sure the vehicle is parked on a level surface. Then check to see if the engine cooling fans are running. If the engine is overheating, both fans should be running. If they are not, do not continue to run the engine and have the vehicle serviced.
Notice: Running the engine without coolant may cause damage or a fire. Vehicle damage would not be covered by the warranty. See Overheated Engine Protection Operating Mode on page 10‑17 for information on driving to a safe place in an emergency. If Steam Is Coming from the Engine Compartment { WARNING
Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Turn it off and get everyone away from the vehicle until it cools down. Wait until there is no sign of steam or coolant before you open the hood.
(Continued)
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (17,1)
WARNING (Continued)
If you keep driving when the vehicles engine is overheated, the liquids in it can catch fire. You or others could be badly burned. Stop the engine if it overheats, and get out of the vehicle until the engine is cool. See Overheated Engine Protection Operating Mode on page 10‑17 for information on driving to a safe place in an emergency.
If No Steam Is Coming from the Engine Compartment If an engine overheat warning is displayed but no steam can be seen or heard, the problem may not be too serious. Sometimes the engine can get a little too hot when the vehicle: . Climbs a long hill on a hot day. . Stops after high-speed driving.
Idles for long periods in traffic. Tows a trailer.
If the overheat warning is displayed with no sign of steam: 1. Turn the air conditioning off. 2. Turn the heater on to the highest
3.
temperature and to the highest fan speed. Open the windows as necessary. If in a traffic jam, shift to N (Neutral); otherwise, shift to the highest gear while driving — D (Drive) or L (Low).
If the temperature overheat gauge is no longer in the overheat zone or an overheat warning no longer displays, the vehicle can be driven. Continue to drive the vehicle slow for about 10 minutes. Keep a safe vehicle distance from the car in front of you. If the warning does not come back on, continue to drive normally. If the warning continues, pull over, stop, and park the vehicle right away.
Vehicle Care
10-17
If there is no sign of steam, idle the engine for three minutes while parked. If the warning is still displayed, turn off the engine until it cools down. Also, see “Overheated Engine Protection Operating Mode” next in this section.
Overheated Engine Protection Operating Mode This emergency operating mode lets the vehicle be driven to a safe place in an emergency situation. If an overheated engine condition exists, an overheat protection mode which alternates firing groups of cylinders helps prevent engine damage. In this mode, there is a significant loss in power and engine performance. The temperature gauge indicates an overheat condition exists. Driving extended distances and/or towing a trailer in the overheat protection mode should be avoided.
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (18,1)
10-18
Vehicle Care
Notice: After driving in the overheated engine protection operating mode, to avoid engine damage, allow the engine to cool before attempting any repair. The engine oil will be severely degraded. Repair the cause of coolant loss, change the oil and reset the oil life system. See Engine Oil on page 10‑7.
Power Steering Fluid
The power steering fluid reservoir is located under the engine cover on the passenger side of the vehicle. See Engine Compartment Overview on page 10‑5 for reservoir location.
When to Check Power Steering Fluid It is not necessary to regularly check power steering fluid unless you suspect there is a leak in the system or you hear an unusual noise. A fluid loss in this system could indicate a problem. Have the system inspected and repaired. How to Check Power Steering Fluid To check the power steering fluid: 1. Turn the key off and let the
engine compartment cool down. 2. Remove the engine cover. See
Engine Cover on page 10‑6.
3. Wipe the cap and the top of the
reservoir clean.
4. Unscrew the cap and wipe the
dipstick with a clean rag.
5. Replace the cap and completely
tighten it.
6. Remove the cap again and look at the fluid level on the dipstick.
The fluid level should be somewhere between the MAX and MIN line on the dipstick in room temperature. If the fluid is on or below the MIN line, add fluid close to the MAX Line. What to Use To determine what kind of fluid to use, see Recommended Fluids and Lubricants on page 11‑12. Always use the proper fluid. Notice: Use of the incorrect fluid may damage the vehicle and the damages may not be covered by the vehicle's warranty. Always use the correct fluid listed in Recommended Fluids and Lubricants on page 11‑12.
Washer Fluid
What to Use When adding windshield washer fluid, be sure to read the manufacturer's instructions before use. If the vehicle will be operating in an area where the temperature
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (19,1)
may fall below freezing, use a fluid that has sufficient protection against freezing. Adding Washer Fluid When the windshield washer fluid reservoir is low, a WASHER FLUID LOW ADD FLUID message will be displayed on the Driver Information Center (DIC). See Washer Fluid Messages on page 5‑37 for more information.
Open the cap with the washer symbol on it. Add washer fluid until the tank is full. See Engine Compartment Overview on page 10‑5 for reservoir location.
Notice
. When using concentrated
washer fluid, follow the manufacturer instructions for adding water.
. Do not mix water with
ready-to-use washer fluid. Water can cause the solution to freeze and damage the washer fluid tank and other parts of the washer system.
. Fill the washer fluid tank only
three-quarters full when it is very cold. This allows for fluid expansion if freezing occurs, which could damage the tank if it is completely full.
. Do not use engine coolant
(antifreeze) in the windshield washer. It can damage the windshield washer system and paint.
Vehicle Care
10-19
Brakes This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal firmly.
{ WARNING
The brake wear warning sound means that soon the brakes will not work well. That could lead to a crash. When the brake wear warning sound is heard, have the vehicle serviced.
Notice: Continuing to drive with worn-out brake pads could result in costly brake repair.
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (20,1)
10-20
Vehicle Care
Some driving conditions or climates can cause a brake squeal when the brakes are first applied or lightly applied. This does not mean something is wrong with the brakes. Properly torqued wheel nuts are necessary to help prevent brake pulsation. When tires are rotated, inspect brake pads for wear and evenly tighten wheel nuts in the proper sequence to torque specifications in Capacities and Specifications on page 12‑2. Brake linings should always be replaced as complete axle sets. Brake Pedal Travel See your dealer if the brake pedal does not return to normal height, or if there is a rapid increase in pedal travel. This could be a sign that brake service might be required.
Brake Adjustment Every time the brakes are applied, with or without the vehicle moving, the brakes adjust for wear. Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. The vehicle was designed and tested with top-quality brake parts. When parts of the braking system are replaced, be sure to get new, approved replacement parts. If this is not done, the brakes might not work properly. For example, installing disc brake pads that are wrong for the vehicle, can change the balance between the front and rear brakes — for the worse. The braking performance expected can change in many other ways if the wrong replacement brake parts are installed.
Brake Fluid
The brake master cylinder reservoir is filled with DOT 3 brake fluid as indicated on the reservoir cap. See Engine Compartment Overview on page 10‑5 for the location of the reservoir. There are only two reasons why the brake fluid level in the reservoir might go down:
The brake fluid level goes down because of normal brake lining wear. When new linings are installed, the fluid level goes back up.
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (21,1)
. A fluid leak in the brake
hydraulic system can also cause a low fluid level. Have the brake hydraulic system fixed, since a leak means that sooner or later the brakes will not work well.
Do not top off the brake fluid. Adding fluid does not correct a leak. If fluid is added when the linings are worn, there will be too much fluid when new brake linings are installed. Add or remove brake fluid, as necessary, only when work is done on the brake hydraulic system.
{ WARNING
If too much brake fluid is added, it can spill on the engine and burn, if the engine is hot enough. You or others could be burned, and the vehicle could be damaged. Add brake fluid only when work is done on the brake hydraulic system.
When the brake fluid falls to a low level, the brake warning light comes on. See Brake System Warning Light on page 5‑18.
What to Add Use only new DOT 3 brake fluid from a sealed container. See Recommended Fluids and Lubricants on page 11‑12. Always clean the brake fluid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir.
{ WARNING
With the wrong kind of fluid in the brake hydraulic system, the brakes might not work well. This could cause a crash. Always use the proper brake fluid.
Vehicle Care
10-21
Notice
. Using the wrong fluid can
badly damage brake hydraulic system parts. For example, just a few drops of mineral-based oil, such as engine oil, in the brake hydraulic system can damage brake hydraulic system parts so badly that they will have to be replaced. Do not let someone put in the wrong kind of fluid.
. If brake fluid is spilled on the
vehicle's painted surfaces, the paint finish can be damaged. Be careful not to spill brake fluid on the vehicle. If you do, wash it off immediately.
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (22,1)
10-22
Vehicle Care
Battery Refer to the replacement number on the original battery label when a new battery is needed.
{ WARNING
Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.
Vehicle Storage
{ WARNING
Batteries have acid that can burn you and gas that can explode. You can be badly hurt if you are not careful. See Jump Starting on page 10‑65 for tips on working around a battery without getting hurt.
Infrequent Usage: Remove the black, negative (−) cable from the battery to keep the battery from running down. Extended Storage: Remove the black, negative (−) cable from the battery or use a battery trickle charger.
All-Wheel Drive Transfer case fluid does not require checking unless there is a fluid leak or unusual noise. If required, have the transfer case serviced by your dealer.
Starter Switch Check
{ WARNING When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured.
1. Before starting this check, be
sure there is enough room around the vehicle.
2. Firmly apply both the parking brake and the regular brake. See Parking Brake on page 9‑26. Do not use the accelerator pedal, and be ready to turn off the engine immediately if it starts.
3. Try to start the engine in each gear. The vehicle should start only in P (Park) or N (Neutral). If the vehicle starts in any other position, contact your dealer for service.
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (23,1)
Automatic Transmission Shift Lock Control Function Check
{ WARNING When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured.
1. Before starting this check, be
sure there is enough room around the vehicle. It should be parked on a level surface.
2. Firmly apply the parking brake.
See Parking Brake on page 9‑26. Be ready to apply the regular brake immediately if the vehicle begins to move.
3. With the engine off, turn the
ignition on, but do not start the engine. Without applying the regular brake, try to move the shift lever out of P (Park) with normal effort. If the shift lever moves out of P (Park), contact your dealer for service.
Ignition Transmission Lock Check While parked, and with the parking brake set, try to turn the ignition to LOCK/OFF in each shift lever position.
The ignition should turn to LOCK/OFF only when the shift lever is in P (Park). The ignition key should come out only in LOCK/OFF.
Contact your dealer if service is required.
Vehicle Care
10-23
Park Brake and P (Park) Mechanism Check { WARNING
When you are doing this check, the vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move.
Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake.
To check the parking brake's holding ability: With the engine running and the transmission in N (Neutral), slowly remove foot pressure from the regular brake pedal. Do this until the vehicle is held by the parking brake only.
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (24,1)
10-24
Vehicle Care
To check the P (Park) mechanism's holding ability: With the engine running, shift to P (Park). Then release the parking brake followed by the regular brake.
Contact your dealer if service is required.
Wiper Blade Replacement
Front Wiper Blade Windshield wiper blades should be inspected for wear or cracking. See Maintenance Schedule on page 11‑3. Replacement blades come in different types and are removed in different ways. For the proper type and size, see Maintenance Replacement Parts on page 11‑13. To replace the wiper blade assembly: 1. Pull the windshield wiper assembly away from the windshield.
2. Squeeze the tabs on each side
of the wiper blade assembly and slide the assembly off the end of the wiper arm.
3.
Install the new blade onto the arm connector and make sure the tabs are fully set in the locked position. Allowing the wiper blade arm to touch the windshield when no wiper blade is installed could damage the windshield. Any damage that occurs would not
be covered by your warranty. Do not allow the wiper blade arm to touch the windshield.
4. Repeat the steps for the other
blade.
Rear Wiper Blade To replace the rear wiper blade: 1. Pull the wiper blade assembly
away from the backglass. The rear wiper blade will not lock in a vertical position so care should be used when pulling it away from the vehicle.
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (25,1)
Headlamp Aiming Headlamp aim has been preset and should need no further adjustment. If the vehicle is damaged in a crash, the headlamp aim may be affected. If adjustment to the headlamps is necessary, see your dealer.
2. Push the release lever (2) to
disengage the hook and push the wiper arm (1) out of the blade assembly (3).
3. Push the new blade assembly securely in the wiper arm hook until the release lever clicks into place.
4. Return the wiper arm and blade assembly to the rest position on the glass.
Windshield Replacement The vehicle is equipped with an acoustic windshield. If you ever have to have the windshield replaced be sure to get an acoustic windshield so you will continue to have the benefits an acoustic windshield can provide.
Vehicle Care
10-25
Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 10‑27. For any bulb‐changing procedure not listed in this section, contact your dealer.
High Intensity Discharge (HID) Lighting
{ WARNING
The high intensity discharge lighting system operates at a very high voltage. If you try to service any of the system components, you could be seriously injured. Have your dealer or a qualified technician service them.
After an HID headlamp bulb has been replaced, the beam might be a slightly different shade than it was originally. This is normal.
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (26,1)
10-26
Vehicle Care
Taillamps, Turn Signal, and Stoplamps
To replace one of these bulbs: 1. Open the liftgate. See Liftgate
on page 2‑8.
2. Using a small flat bladed tool,
remove the screw covers by prying them from the bottom. 3. Remove the two hex screws
holding the taillamp assembly in place.
4. Pull out the taillamp assembly. 5. Turn the bulb socket
counterclockwise and pull it straight out to remove it.
6. Replace the bulb. 7. Reverse Steps 3–5 to reinstall
the taillamp assembly. When reinstalling the taillamp assembly, the pin on the taillamp assembly must line up and be inserted correctly into the opening.
8. Replace the screw covers.
License Plate Lamp To replace one of these bulbs: 1. Remove the two push pins
holding each of the license plate lamps to the liftgate trim by unscrewing them.
2. Turn and pull the license plate
lamp forward through the liftgate trim opening.
3. Turn the bulb socket
counterclockwise and pull the bulb straight out of the socket. Install the new bulb.
4. 5. Reverse Steps 1–3 to reinstall
the license plate lamp.
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (27,1)
Replacement Bulbs
Electrical System
Exterior Lamp
License Plate Lamp Rear Turn Signal and Taillamps
Bulb
Number
194LL
7443
(W21/5W)
For replacement bulbs not listed here, contact your dealer.
High Voltage Devices and Wiring
{ WARNING
Exposure to high voltage can cause shock, burns, and even death. The high voltage components in the vehicle can only be serviced by technicians with special training. High voltage components are identified by labels. Do not remove, open, take apart, or modify these components. High voltage cable or wiring has orange covering. Do not probe, tamper with, cut, or modify high voltage cable or wiring.
Vehicle Care
10-27
Electrical System Overload The vehicle has fuses and circuit breakers to protect against an electrical system overload. When the current electrical load is too heavy, the circuit breaker opens and closes, protecting the circuit until the current load returns to normal or the problem is fixed. This greatly reduces the chance of circuit overload and fire caused by electrical problems. Fuses and circuit breakers protect power devices in the vehicle. Replace a bad fuse with a new one of the identical size and rating. If there is a problem on the road and a fuse needs to be replaced, the same amperage fuse can be borrowed. Choose some feature of the vehicle that is not needed to use and replace it as soon as possible.
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (28,1)
10-28
Vehicle Care
Headlamp Wiring An electrical overload may cause the lamps to go on and off, or in some cases to remain off. Have the headlamp wiring checked right away if the lamps go on and off or remain off. Windshield Wipers If the wiper motor overheats due to heavy snow or ice, the windshield wipers will stop until the motor cools and will then restart. Although the circuit is protected from electrical overload, overload due to heavy snow or ice may cause wiper linkage damage. Always clear ice and heavy snow from the windshield before using the windshield wipers. If the overload is caused by an electrical problem and not snow or ice, be sure to get it fixed.
Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses, circuit breakers and fusible thermal links. This greatly reduces the chance of fires caused by electrical problems. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure you replace a bad fuse with a new one of the identical size and rating. Fuses of the same amperage can be temporarily borrowed from another fuse location, if a fuse goes out. Replace the fuse as soon as you can.
Engine Compartment Fuse Block The underhood fuse block is in the engine compartment, on the passenger side of the vehicle.
Lift the cover for access to the fuse/ relay block. Notice: Spilling liquid on any electrical component on the vehicle may damage it. Always keep the covers on any electrical component. To remove fuses, hold the end of the fuse between your thumb and index finger and pull straight out.
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (29,1)
Vehicle Care
10-29
Fuses
Usage
A/C CLTCH Air Conditioning
ABS MTR
Clutch Antilock Brake System (ABS) Motor Adaptive Forward Lighting System Airbag System AUX POWER Auxiliary Power
AIRBAG
AFS
AUX
VAC PUMP
AWD
BATT 1
BATT 2
BATT 3
CIGAR
LIGHTER
ECM 1
Auxiliary
Vacuum Pump
All-Wheel-Drive
System
Battery 1
Battery 2
Battery 3
Cigarette Lighter
Engine Control
Module 1
EMISSION 1 Emission 1
The vehicle may not be equipped with all of the fuses, relays, and features shown.
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (30,1)
10-30
Vehicle Care
Fuses
Usage
Fuses
Usage
EMISSION 2 Emission 2
EVEN COILS Even Injector Coils
FAN 1
FAN 2
FSCM
HORN
HTD MIR
HUMIDITY/
MAF
Cooling Fan 1
Cooling Fan 2
Headlamp Washer
(China)/Fog
Lamps (GMC)
Fuel System
Control Module
Horn
Heated Outside
Rearview Mirror
Humidity Sensor/
MAF Sensor
HVAC BLWR Heating,
Ventilation, and Air Conditioning Blower
LT HI BEAM Left High-Beam
Headlamp
LT LO BEAM Left Low-Beam
LT PRK LT TRLR STOP/TRN
Headlamp Left Parking Lamp Trailer Left Stoplamp and Turn Signal
PCM IGN
ODD COILS Odd Injector Coils Powertrain Control Module Ignition PWR L/GATE Power Liftgate
PWR
OUTLET RR APO
Power Outlet
Rear Accessory Power Outlet
RR DEFOG Rear Defogger RR HVAC
Rear Climate Control System
RT HI BEAM Right High-Beam
Headlamp
RT LO BEAM Right Low-Beam
Fuses RT PRK
RT TRLR STOP/TRN
Usage
Right Parking Lamp Trailer Right Stoplamp and Turn Signal
RVC SNSR Regulated Voltage
S/ROOF/
SUNSHADE
SERVICE SPARE STOP LAMPS
(China Only)
STRTR
TCM
TRANS TRLR
BCK/UP
Control Sensor Sunroof
Service Repair Spare Stoplamps (China Only)
Starter Transmission Control Module Transmission Trailer Back-up Lamps
Headlamp
TRLR BRK Trailer Brake
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (31,1)
Usage
Fuses TRLR
Trailer Parking Lamps
PRK LAMP TRLR PWR Trailer Power WPR/WSW Windshield Wiper/
Washer
Usage
Air Conditioning Compressor Clutch
Auxiliary
Vacuum Pump
Switched Power
Cooling Fan 1
Cooling Fan 2
Cooling Fan 3
Headlamp Washer
(China)/Fog
Lamps (GMC)
Relays
A/C
CMPRSR CLTCH
AUX
VAC PUMP
CRNK
FAN 1
FAN 2
FAN 3
HDLP WASH
(CHINA)
FOG
LAMP (GMC)
Relays HI BEAM
HID/
LO BEAM
HORN
IGN
LT TRLR STOP/TRN
Usage
High-Beam Headlamps High Intensity Discharge (HID) Low-Beam Headlamps Horn Ignition Main Trailer Left Stoplamp and Turn Signal Lamp
PRK LAMP Parking Lamp PWR/TRN RR DEFOG Rear Window
Powertrain
RT TRLR STOP/TRN
Stop Lamps (China Only)
TRLR
BCK/UP
Defogger Trailer Right Stoplamp and Turn Signal Lamp Stop Lamps (China Only) Trailer Back-up Lamps
Vehicle Care
10-31
Relays WPR
WPR HI
Usage
Windshield Wiper Windshield Wiper High Speed
Instrument Panel Fuse Block
The instrument panel fuse block is under the instrument panel on the passenger side of the vehicle. Pull down on the cover to access the fuse block.
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (32,1)
10-32
Vehicle Care
Fuses
Usage
) )
) ) )
AIRBAG
AMP BCK
UP/STOP
BCM
CNSTR VENT CTSY DR LCK
GMC NON HID = Lo Beam GMC NON HID = High Shutter Chevy = Fog Lamps Buick China = Rear Fog Lamp Airbag Amplifier Back-up Lamp/ Stoplamp Body Control Module Canister Vent
Courtesy Lamps Door Locks
Fuses DRL/
LO BEAM
DSPLY EMPTY
Usage
Daytime Running Lamps Relay/Low Beam Headlamps Relay Display Empty
FRT WSW Front Windshield
HTD/
COOL SEAT
HVAC
INADV PWR INT LAMPS
INFOTMNT/
MSM
Washer Heated/Cooling Seats Heating, Ventilation, and Air Conditioning Inadvertent Power/ Interior Light Pipe Lamps Infotainment/ Memory Seat Module
LT TRN SIG Driver Side Turn
Signal
Fuse Side
The vehicle may not be equipped with all of the fuses, relays, and features shown.
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (33,1)
Vehicle Care
10-33
Fuses PDM
Usage
Power Mirrors, Liftgate Release
PWR MODE Power Mode
PWR MIR
RDO
Power Mirrors Radio
REAR WPR Rear Wiper
RPA/
SBZA/UGDO
Rear Park Assist/ Side Blind Zone Alert/Universal Garage Door Opener
RT TRN SIG Passenger Side
STR WHL
ILLUM
Turn Signal Steering Wheel Illumination
Relays
LT/
PWR/SEAT
RT/
Usage
Driver Side Power Seat Relay Passenger Side Power Seat Relay
PWR/SEAT PWR/WNDW Power Windows
PWR/
COLUMN L/GATE
LCK
Relay Power Steering Column Relay Liftgate Relay Power Lock Relay
UNLCK
REAR/WSW Rear Window Washer Relay Power Unlock Relay Daytime Running Lamps Relay/Low Beam Headlamps Relay
LO BEAM
DRL/
Relay Side
LT/UNLCK Driver Side Unlock
Relay
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (34,1)
10-34
Vehicle Care
Relays DRL/
LO BEAM
Usage
Daytime Running Lamps Relay (If Equipped)
FOG LAMPS Fog Lamps Relay
(Chevy)
FRT/WSW Front Windshield
Washer Relay
Wheels and Tires
Tires Every new GM vehicle has high-quality tires made by a leading tire manufacturer. See the warranty manual for information regarding the tire warranty and where to get service. For additional information refer to the tire manufacturer.
{ WARNING
. Poorly maintained and
improperly used tires are dangerous.
. Overloading the tires can
cause overheating as a result of too much flexing. There could be a blowout
(Continued)
WARNING (Continued)
and a serious crash. See Vehicle Load Limits on page 9‑9.
. Underinflated tires pose
the same danger as overloaded tires. The resulting crash could cause serious injury. Check all tires frequently to maintain the recommended pressure. Tire pressure should be checked when the tires are cold.
. Overinflated tires are more likely to be cut, punctured, or broken by a sudden impact — such as when hitting a pothole. Keep tires at the recommended pressure.
(Continued)
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (35,1)
All-Season Tires This vehicle may come with all-season tires. These tires are designed to provide good overall performance on most road surfaces and weather conditions. Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. Original equipment all-season tires can be identified by the last two characters of this TPC code, which will be “MS.” Consider installing winter tires on the vehicle if frequent driving on snow or ice-covered roads is expected. All-season tires provide adequate performance for most winter driving conditions, but they may not offer the same level of traction or performance as winter tires on snow or ice-covered roads. See Winter Tires on page 10‑35.
Vehicle Care
10-35
Winter Tires This vehicle was not, originally, equipped with winter tires. Winter tires are designed for increased traction on snow and ice-covered roads. Consider installing winter tires on the vehicle if frequent driving on snow or ice-covered roads is expected. See your dealer for details regarding winter tire availability and proper tire selection. Also, see Buying New Tires on page 10‑49. With winter tires, there may be decreased dry road traction, increased road noise, and shorter tread life. After changing to winter tires, be alert for changes in vehicle handling and braking. If using winter tires: . Use tires of the same brand and
tread type on all four wheel positions.
WARNING (Continued)
. Worn or old tires can
cause a crash. If the tread is badly worn, replace them.
. Replace any tires that
have been damaged by impacts with potholes, curbs, etc.
. Improperly repaired tires can cause a crash. Only the dealer or an authorized tire service center should repair, replace, dismount, and mount the tires.
. Do not spin the tires in
excess of 56 km/h (35 mph) on slippery surfaces such as snow, mud, ice, etc. Excessive spinning may cause the tires to explode.
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (36,1)
10-36
Vehicle Care
. Use only radial ply tires of the
same size, load range, and speed rating as the original equipment tires.
Winter tires with the same speed rating as the original equipment tires may not be available for H, V, W, Y, and ZR speed rated tires. If winter tires with a lower speed rating are chosen, never exceed the tire's maximum speed capability.
Summer Tires This vehicle may come with high performance summer tires. These tires have a special tread and compound that are optimized for maximum dry and wet road performance. This special tread and compound will decrease performance in cold climates, and on ice and snow. We recommend installing winter tires on the vehicle if frequent driving in cold temperatures or on snow or ice covered roads is expected. See Winter Tires on page 10‑35.
Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples show a typical passenger vehicle tire and a compact spare tire sidewall.
Passenger (P-Metric) Tire Example (1) Tire Size: The tire size is a combination of letters and numbers used to define a particular tire's width, height, aspect ratio, construction type,
and service description. See the “Tire Size” illustration later in this section. (2) TPC Spec (Tire Performance Criteria Specification): Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. GM's TPC specifications meet or exceed all federal safety guidelines. (3) DOT (Department of Transportation): The Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S. Department of Transportation Motor Vehicle Safety Standards. DOT Tire Date of Manufacture: The last four digits of the TIN indicate the tire manufactured date. The first two
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (37,1)
digits represent the week (01–52) and the last two digits, the year. For example, the third week of the year 2010 would have a four-digit DOT date of 0310. (4) Tire Identification Number (TIN): The letters and numbers following the DOT (Department of Transportation) code are the Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (5) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread. (6) Uniform Tire Quality Grading (UTQG): Tire manufacturers are required to grade tires based on three
performance factors: treadwear, traction, and temperature resistance. For more information see Uniform Tire Quality Grading on page 10‑51. (7) Maximum Cold Inflation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load.
Compact Spare Tire Example (1) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread.
Vehicle Care
10-37
(2) Temporary Use Only: The compact spare tire or temporary use tire should not be driven at speeds over 80 km/h (50 mph). The compact spare tire is for emergency use when a regular road tire has lost air and gone flat. If the vehicle has a compact spare tire, see Compact Spare Tire on page 10‑64 and If a Tire Goes Flat on page 10‑54. (3) Tire Identification Number (TIN): The letters and numbers following the DOT (Department of Transportation) code are the Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture.
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (38,1)
10-38
Vehicle Care
(4) Maximum Cold Inflation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load. (5) Tire Inflation: The temporary use tire or compact spare tire should be inflated to 420 kPa (60 psi). For more information on tire pressure and inflation see Tire Pressure on page 10‑41. (6) Tire Size: A combination of letters and numbers define a tire's width, height, aspect ratio, construction type, and service description. The letter T as the first character in the tire size means the tire is for temporary use only. (7) TPC Spec (Tire Performance Criteria Specification): Original equipment tires designed to GM's specific tire performance
criteria have a TPC specification code molded onto the sidewall. GM's TPC specifications meet or exceed all federal safety guidelines.
Tire Designations
Tire Size The following is an example of a typical passenger vehicle tire size.
(1) Passenger (P-Metric) Tire: The United States version of a metric tire sizing system. The letter P as the first character in the tire size means a passenger
vehicle tire engineered to standards set by the U.S. Tire and Rim Association. (2) Tire Width: The three-digit number indicates the tire section width in millimeters from sidewall to sidewall. (3) Aspect Ratio: A two-digit number that indicates the tire height-to-width measurements. For example, if the tire size aspect ratio is 60, as shown in item 3 of the illustration, it would mean that the tire's sidewall is 60 percent as high as it is wide. (4) Construction Code: A letter code is used to indicate the type of ply construction in the tire. The letter R means radial ply construction; the letter D means diagonal or bias ply construction; and the letter B means belted-bias ply construction.
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (39,1)
(5) Rim Diameter: Diameter of the wheel in inches. (6) Service Description: These characters represent the load index and speed rating of the tire. The load index represents the load carrying capacity a tire is certified to carry. The speed rating is the maximum speed a tire is certified to carry a load.
Tire Terminology and Definitions Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in kPa (kilopascal) or psi (pounds per square inch). Accessory Weight: The combined weight of optional accessories. Some examples of optional accessories are automatic transmission, power
steering, power brakes, power windows, power seats, and air conditioning. Aspect Ratio: The relationship of a tire's height to its width. Belt: A rubber coated layer of cords between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread. Cold Tire Pressure: The amount of air pressure in a tire, measured in kPa (kilopascal) or psi (pounds per square inch)
Vehicle Care
10-39
before a tire has built up heat from driving. See Tire Pressure on page 10‑41. Curb Weight: The weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil, and coolant, but without passengers and cargo. DOT Markings: A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation (DOT) Motor Vehicle Safety Standards. The DOT code includes the Tire Identification Number (TIN), an alphanumeric designator which can also identify the tire manufacturer, production plant, brand, and date of production. GVWR: Gross Vehicle Weight Rating. See Vehicle Load Limits on page 9‑9.
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (40,1)
10-40
Vehicle Care
GAWR FRT: Gross Axle Weight
Rating for the front axle. See
Vehicle Load Limits on
page 9‑9.
GAWR RR: Gross Axle Weight
Rating for the rear axle. See
Vehicle Load Limits on
page 9‑9.
Intended Outboard Sidewall:
The side of an asymmetrical tire,
that must always face outward
when mounted on a vehicle.
Kilopascal (kPa): The metric
unit for air pressure.
Light Truck (LT-Metric) Tire: A
tire used on light duty trucks and
some multipurpose passenger
vehicles.
Load Index: An assigned
number ranging from 1 to 279
that corresponds to the load
carrying capacity of a tire.
Maximum Inflation Pressure: The maximum air pressure to which a cold tire can be inflated. The maximum air pressure is molded onto the sidewall. Maximum Load Rating: The load rating for a tire at the maximum permissible inflation pressure for that tire. Maximum Loaded Vehicle Weight: The sum of curb weight, accessory weight, vehicle capacity weight, and production options weight. Normal Occupant Weight: The number of occupants a vehicle is designed to seat multiplied by 68 kg (150 lb). See Vehicle Load Limits on page 9‑9. Occupant Distribution: Designated seating positions.
Outward Facing Sidewall: The side of an asymmetrical tire that has a particular side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering, or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire. Passenger (P-Metric) Tire: A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inflation Pressure: Vehicle manufacturer's recommended tire inflation pressure as shown on the tire placard. See Tire Pressure on page 10‑41 and Vehicle Load Limits on page 9‑9.
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (41,1)
Radial Ply Tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim: A metal support for a tire and upon which the tire beads are seated. Sidewall: The portion of a tire between the tread and the bead. Speed Rating: An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. Traction: The friction between the tire and the road surface. The amount of grip provided. Tread: The portion of a tire that comes into contact with the road.
Treadwear Indicators: Narrow bands, sometimes called wear bars, that show across the tread of a tire when only 1.6 mm (1/16 in) of tread remains. See When It Is Time for New Tires on page 10‑48. UTQGS (Uniform Tire Quality Grading Standards): A tire information system that provides consumers with ratings for a tire's traction, temperature, and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire. See Uniform Tire Quality Grading on page 10‑51. Vehicle Capacity Weight: The number of designated seating positions multiplied by
Vehicle Care
10-41
68 kg (150 lb) plus the rated cargo load. See Vehicle Load Limits on page 9‑9. Vehicle Maximum Load on the Tire: Load on an individual tire due to curb weight, accessory weight, occupant weight, and cargo weight. Vehicle Placard: A label permanently attached to a vehicle showing the vehicle capacity weight and the original equipment tire size and recommended inflation pressure. See “Tire and Loading Information Label” under Vehicle Load Limits on page 9‑9.
Tire Pressure Tires need the correct amount of air pressure to operate effectively.
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (42,1)
10-42
Vehicle Care
Notice: Neither tire underinflation nor overinflation is good. Underinflated tires, or tires that do not have enough air, can result in:
. Tire overloading and
overheating which could lead to a blowout.
. Premature or
irregular wear. . Poor handling. . Reduced fuel economy.
Overinflated tires, or tires that have too much air, can result in:
. Unusual wear. . Poor handling. . Rough ride. . Needless damage from
road hazards.
The Tire and Loading Information label on the vehicle indicates the original equipment tires and the correct cold tire inflation pressures. The recommended pressure is the minimum air pressure needed to support the vehicle's maximum load carrying capacity. See Vehicle Load Limits on page 9‑9. How the vehicle is loaded affects vehicle handling and ride comfort. Never load the vehicle with more weight than it was designed to carry.
When to Check Check the tires once a month or more. Do not forget the compact spare, if the vehicle has one. The cold compact spare tire pressure should be at 420 kPa (60 psi). See Compact Spare Tire on page 10‑64.
How to Check Use a good quality pocket-type gauge to check tire pressure. Proper tire inflation cannot be determined by looking at the tire. Check the tire inflation pressure when the tires are cold, meaning the vehicle has not been driven for at least three hours or no more than 1.6 km (1 mi). Remove the valve cap from the tire valve stem. Press the tire gauge firmly onto the valve to get a pressure measurement. If the cold tire inflation pressure matches the recommended pressure on the Tire and Loading Information label, no further adjustment is necessary. If the inflation pressure is low, add air until the recommended pressure is reached. If the inflation pressure is high, press on the metal stem in the center of the tire valve to release air.
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (43,1)
Recheck the tire pressure with the tire gauge. Return the valve caps on the valve stems to prevent leaks and keep out dirt and moisture.
Tire Pressure Monitor System The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your tires and transmit tire pressure readings to a receiver located in the vehicle. Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or
tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle's handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver's responsibility to maintain correct tire pressure, even if under-inflation has
Vehicle Care
10-43
not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to
Buick Enclave Owner Manual - 2013 - crc - 11/14/12
Black plate (44,1)
10-44
Vehicle Care
ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. See Tire Pressure Monitor Operation on page 10‑44. Federal Communications Commission (FCC) Rules and