Login- Download PDF Manual
-
Replacing components
Onboard toolkit
BMW X5: rear
The onboard toolkit is located in the cargo bay under the floor panel.
Replacing wiper blades
Front
1. Fold down the wiper arm. 2. Swing the wiper blade upward. 3. Remove the wiper blade toward the wind-
shield, refer to arrow.
1. Lift off the wiper arm completely and pull off
the wiper blade, refer to arrow.
2. Mount the new wiper blade and press on
until it is heard to engage.
Lamps and bulbs Lamps and bulbs make an essential contribu- tion to vehicle safety. You must be duly diligent in replacing them. BMW recommends having your BMW Sports Activity Vehicle Center per- form any work that you do not feel competent to perform yourself or that is not described here. Never touch the glass of new bulbs with your bare fingers, as even minute
amounts of contamination will burn into the bulb's surface and reduce its service life. Use a clean cloth, napkin, etc., or hold the bulb by its metal socket.< A replacement bulb set is available from your BMW Sports Activity Vehicle Center.
Only replace bulbs when cool, as other- wise you may be burned.< Whenever you perform any work on the electrical system, turn off the systems/ consumers involved to prevent short circuits from occurring. To avoid possible injury or equipment damage when replacing bulbs, observe any instructions provided by the bulb manufacturer.<
250
ba8_e70ag.book Seite 251 Freitag, 5. Juni 2009 11:42 11
When performing care and maintenance on the headlamps, please observe the information on page 247.
For bulbs for which replacement is not described and for checking and adjusting
headlamp aim, please contact your BMW Sports Activity Vehicle Center.<
Light-emitting diodes LEDs Light-emitting diodes installed behind translu- cent lenses serve as the light source for many of the controls and displays in your vehicle. These light-emitting diodes, which operate using a concept similar to that applied in conventional lasers, are officially designated as Class 1 light- emitting diodes.
Do not remove the covers, and never stare into the unfiltered light for several hours, as irritation of the retina could result.<
BMW X5: changing lamps
Xenon lamps These bulbs have a very long service life and the probability of a failure is very low. If a lamp should nevertheless fail, you can continue driv- ing cautiously with fog lamps* provided that this is permitted by the country-specific laws. Have work on the xenon light unit includ- ing changing the bulb carried out only by your BMW Sports Activity Vehicle Center or a workshop that works according to BMW repair procedures with correspondingly trained per- sonnel. Due to the high voltage present in the system, there is a danger of fatal injuries when work is carried out improperly.<
Halogen bulbs: Parking lamps and roadside parking lamps, daytime driving lamps 35-Watt bulb, H8
The bulb is pressurized. Therefore, wear safety glasses and protective gloves. Otherwise there is a danger of injuries if the bulb is accidentally damaged during replace- ment.<
1. Turn the cover to the left and remove.
2. Turn the bulbs to the left, pull off the con-
nector and replace. Install in the reverse order.
3.
Turn signals, front 24-Watt bulb, PY24W 1. Unscrew bulb holder with bulb to the left,
refer to arrow, and replace.
2.
Install in the reverse order.
Side marker lamps, rear To replace, please go to a BMW Sports Activity Vehicle Center or a workshop that works according to BMW repair procedures with cor- respondingly trained personnel.
Tail lamps > Turn signals, brake lamps: 21-watt bulb,
P21W
> Backup lamps and brake force display: 16-
watt bulb, W16W
> Rear lamp: LED technology.
In case of a defect, please go to a BMW Sports Activity Vehicle Center or a work- shop that works according to BMW repair
251
ba8_e70ag.book Seite 252 Freitag, 5. Juni 2009 11:42 11
procedures with correspondingly trained personnel.
Arrangement of tail lamps
Turn signal 1. Open the side panel in the cargo bay. 2. Remove the first-aid kit* and warning trian-
gle* if necessary. Fold up the insulation.
3. Rotate the bulb socket to the left and
remove.
1 Rear lamp 2 Brake force display 3 Turn signal 4 Brake lamp/rear lamp/side marker lamp 5 Backup lamp 6 Brake lamp
4. Apply gentle pressure to the bulb while
turning it to the left for removal and replace- ment.
5. Remount the side panel.
Brake lamps 1. Open the side panel in the cargo bay. 2. Remove the first-aid kit* and warning trian-
gle* if necessary. Fold up the insulation.
3. Rotate the relevant bulb socket to the left
and remove.
Backup lamp 1. Open the side panel in the cargo bay. 2. Remove the first-aid kit* and warning trian-
gle* if necessary. Fold up the insulation.
3. Rotate the bulb socket to the left and
remove.
4. Remove the upper bulb for replacement. Apply gentle pressure to the lower bulb while turning it to the left for removal and replacement.
5. Remount the side panel.
4. Remove the bulb for replacement. 5. Remount the side panel.
252
ba8_e70ag.book Seite 253 Freitag, 5. Juni 2009 11:42 11
Brake force display 1. Carefully remove the cover in the liftgate
panel with a screwdriver.
6. Position the cargo bay lamp and clip it in,
refer to arrow.
2. Rotate the bulb socket to the left and
remove.
License plate lamp 5-watt bulb, C11 12W 1. Slide the lamp to the right with a screw-
driver, refer to arrow 1.
3. Apply gentle pressure to the bulb while
turning it to the left for removal and replace- ment. Insert the bulb socket in the liftgate and engage it.
4.
5. Before installing the cap, unclip the cargo
bay lamp. Then lay the cap on its upper side and close it, refer to arrow.
2. Remove the lamp, arrow 2. 3. Replace the bulb. 4. Reinstall the lamp.
Center brake lamp This lamp uses LED technology for operation. In case of a defect, please go to a BMW Sports Activity Vehicle Center or a workshop that works according to BMW repair procedures with correspondingly trained personnel.
BMW X6: changing lamps
Xenon lamps These bulbs have a very long service life and the probability of a failure is very low. If a lamp should nevertheless fail, you can continue driv- ing cautiously with fog lamps* provided that this is permitted by the country-specific laws.
253
ba8_e70ag.book Seite 254 Freitag, 5. Juni 2009 11:42 11
Have work on the xenon light unit includ- ing changing the bulb carried out only by your BMW Sports Activity Vehicle Center or a workshop that works according to BMW repair procedures with correspondingly trained per- sonnel. Due to the high voltage present in the system, there is a danger of fatal injuries when work is carried out improperly.<
Parking lamps and roadside parking lamps, daytime driving lamps 35-Watt bulb, H8
The bulb is pressurized. Therefore, wear safety glasses and protective gloves. Otherwise there is a danger of injuries if the bulb is accidentally damaged during replace- ment.< 1. Turn the cover to the left and remove.
2. Left side of vehicle:
Rotate the bulb holder to the right, refer to arrow, and remove. Right side of vehicle: Rotate the bulb holder to the left and remove.
3. Disconnect plug and replace bulb. 4.
Install in the reverse order.
254
Side marker lamps 5-Watt bulb, WY5W XLL 1. Rotate the bulb holder to the left and
remove.
2. Pull the bulb out of the bulb holder and
replace. Install in the reverse order.
3.
Turn signals, front 24-Watt bulb, PY24W 1. Rotate bulb holder to the left and remove it
along with the bulb.
2. Rotate the bulb to the right along with the
socket and replace. Install in the reverse order.
3.
Tail lamps > Turn signals, backup lamps: 21-watt bulb,
H21W
> Brake lamps, brake force display: 21-watt
bulb, P21W
> Rear lamp: LED technology.
In case of a defect, please go to a BMW Sports Activity Vehicle Center or a work- shop that works according to BMW repair
ba8_e70ag.book Seite 255 Freitag, 5. Juni 2009 11:42 11
procedures with correspondingly trained personnel.
3. Remove bulb holder along with bulb and
replace.
Arrangement of tail lamps
4.
Install in the reverse order.
Backup lamp 1. Open the side panel in the cargo bay. 2. Remove the first-aid kit* and warning trian-
gle* if necessary.
3. Remove bulb holder along with bulb and
replace.
1 Brake force display/rear lamps 2 Brake lamp/rear lamp 3 Backup lamp 4 Turn signal
Brake lamps 1. Open the side panel in the cargo bay. 2. Remove the first-aid kit* and warning trian-
gle* if necessary.
3. Rotate the relevant bulb socket to the left
and remove.
4. Apply gentle pressure to the bulb while
turning it to the left for removal and replace- ment. Install in the reverse order.
5.
Turn signal 1. Open the side panel in the cargo bay. 2. Remove the first-aid kit* and warning trian-
gle* if necessary.
4.
Install in the reverse order.
Brake force display 1. Carefully remove the cover in the liftgate
panel with a screwdriver.
2. Rotate the bulb socket to the left and
remove.
255
ba8_e70ag.book Seite 256 Freitag, 5. Juni 2009 11:42 11
Changing wheels Your BMW is equipped with run-flat tires as standard. As a result, it is not necessary to change the wheel immediately in the case of air loss in the event of a breakdown. To continue driving with a damaged tire: > With Flat Tire Monitor, refer to Indication of
a flat tire page 93
> With Tire Pressure Monitor, refer to Mes-
sage with low tire inflation pressure page 95
You will recognize run-flat tires by a circular symbol containing the letters RSC on the side of the tire, refer to Run-flat tires, page 237. When mounting new tires, or changing from summer to winter tires or vice versa, use run-flat tires for your own safety. No spare tire is avail- able in case of a flat tire. Your BMW Sports Activity Vehicle Center will be happy to advise you. Also refer to New wheels and tires, page 237.
BMW X6: do not rotate the front wheels to the rear or vice versa, as otherwise the
handling characteristics will be negatively affected.<
Suitable tools for changing tires are avail- able as accessories at your BMW Sports
Activity Vehicle Center.<
Jacking points for vehicle jack
The jacking points for the vehicle jack are located in the positions shown.
Compact wheel*
Safety precautions in the event of a flat tire or wheel change: park the vehicle as far as possible from passing traffic and on solid
3. Apply gentle pressure to the bulb while
turning it to the left for removal and replace- ment. Insert the bulb socket in the liftgate and engage it.
4.
5. Replace the cover.
License plate lamp 5-Watt bulb, C5W 1. Slide the lamp to the right with a screw-
driver, refer to arrow 1.
2. Remove the lamp, arrow 2. 3. Replace the bulb. 4. Reinstall the lamp.
Center brake lamp This lamp uses LED technology for operation. In case of a defect, please go to a BMW Sports Activity Vehicle Center or a workshop that works according to BMW repair procedures with correspondingly trained personnel.
256
ba8_e70ag.book Seite 257 Freitag, 5. Juni 2009 11:42 11
ground. Switch on the hazard warning flashers. Set the parking brake and engage transmission position P. Have all vehicle occupants get out of the vehicle and ensure that they remain outside the imme- diate area in a safe place, such as behind a guardrail. If a warning triangle* or portable hazard warning lamp* is required, set it up on the roadside at an appropriate distance from the rear of the vehi- cle. Comply with all safety guidelines and regu- lations. Change the wheel only on a level, firm surface which is not slippery. The vehicle or the jack could slip to the side if you attempt to raise the vehicle on a soft or slippery surface such as snow, ice, tiles, etc. Position the jack on a firm support surface. Do not use a wooden block or similar object as a support base for the jack, as this would prevent it from extending to its full support height and reduce its load-carrying capacity. To avoid serious or fatal injury: never lie under the vehicle, and never start the engine while it is supported by the jack.<
What you will need To avoid rattling noises later on, note the posi- tions of the tools before removing them, then return them to their initial positions after com- pleting work. The tools are located in the mount under the floor panel flap.
Removing compact wheel The compact wheel is located in the cargo bay under the floor panel.
1. Remove the tool mount. 2. Unscrew the wing nut 1. 3. Remove the washer 2 laterally. 4. Remove the compact wheel.
Preparing wheel change 1. Observe the safety precautions above. 2. Loosen the lug bolts a half turn.
Jacking up vehicle 1. Position the vehicle jack at the jacking point closest to the wheel so that the entire sur- face of the jack base rests on the ground perpendicularly beneath the jacking point.
The vehicle jack is designed for changing wheels only. Do not attempt to raise another vehicle model with it or to raise any load of any kind. To do so could cause accidents and personal injury.<
1 Vehicle jack* 2 Vehicle jack crank* 3 Lug wrench*
257
ba8_e70ag.book Seite 258 Freitag, 5. Juni 2009 11:42 11
2. Guide the jack head into the rectangular
3. Check and correct the tire inflation pressure
recess of the jacking point when cranking up, refer to illustration detail.
3. Jack the vehicle up until the wheel you are
changing is raised from the ground.
Mounting a wheel 1. Unscrew the lug bolts and remove the
wheel.
2. Remove accumulations of mud or dirt from
the mounting surfaces of the wheel and hub. Also clean the lug bolts.
3. Position the new wheel or compact wheel. Secure the wheel by screwing at least two lug bolts into opposite bolt holes. When you mount wheels other than Genu- ine BMW light-alloy wheels, different lug bolts may also be required.
4. Screw in the remaining lug bolts. Tighten all
the bolts securely in a diagonal pattern.
5. Lower the vehicle and remove the jack from
beneath the vehicle.
After mounting 1. Tighten the lug bolts in a diagonal pattern.
To ensure safety, always have the lug bolts checked with a calibrated
torque wrench as soon as possible to ensure that they are tightened to the speci- fied torque. Otherwise, incorrectly tight- ened lug bolts are a hidden safety risk. The tightening torque is 101 lb ft/140 Nm.<
2. Stow the defective wheel in the cargo bay. The defective wheel cannot be stored under the floor panel flap due to its
size.<
258
at the earliest opportunity.
Protect valve stems with valve screw caps against dirt and contamination. Dirt in valve stems is a frequent source of gradual air loss.< Initialize the Flat Tire Monitor, refer to page 93, or reset the Tire Pressure Monitor, refer to page 94.
4.
5. Replace the damaged tire as soon as possi-
ble and have the new wheel/tire balanced.
Driving with compact wheel
Drive reservedly and do not exceed a speed of 50 mph/80 km/h. Otherwise, changes in the driving characteristics could result, for example reduced track stability on braking, extended braking distance, and altered self-steering characteristics in the limit range. In conjunction with winter tires, these charac- teristics are more pronounced.<
Only one compact wheel may be mounted. Restore the wheels and tires to their original size as quickly as possible. Failure to do so is a safety risk.<
Vehicle battery
Battery care The battery is 100% maintenance-free, i.e., the electrolyte will last for the life of the battery when the vehicle is operated in a temperate cli- mate. Your BMW Sports Activity Vehicle Center will be glad to advise in all matters concerning the battery.
Charging battery Only charge the battery in the vehicle via the terminals in the engine compartment with the engine switched off. Connections, refer to Jump starting on page 262.
Disposal
Have old batteries disposed of following replacement at your BMW Sports Activity
ba8_e70ag.book Seite 259 Freitag, 5. Juni 2009 11:42 11
Vehicle Center or bring them to a collection point. Maintain the battery in an upright position for transport and storage. Always restrain the battery to prevent it from tipping over during transport.<
Power failure Following a temporary power failure, e.g. due to a discharged battery, the use of some equip- ment will be restricted, requiring its reinitializa- tion. In the same way, individual settings are lost and must be updated again: > Seat, mirror and steering wheel memory
The positions must be stored again, refer to page 45.
> Time and Date
The values must be updated again, refer to pages 79, 80.
> Radio
Radio stations must be stored again, refer to page 164.
> Navigation system
You must wait until the system becomes functional again, refer to page 157.
> Glass sunroof/panorama glass sunroof
It may only be possible to raise the glass sunroof/panorama glass sunroof The sys- tem must be initialized, refer to page 42.
> Digital compass
The system must be calibrated, refer to page 118.
> Active steering
The system automatically initializes for a short time as you drive. During this time, the system is deactivated, refer to page 97.
> xDrive
The system automatically initializes as you drive. During this time, indicator lamps light up. If the lamps do not disappear during the current trip, have the system checked.
Before removing the vehicle from stor- age, consult your BMW Sports Activity
Vehicle Center.<
Fuses
Never attempt to repair a blown fuse and do not replace a defective fuse with a sub- stitute of another color or amperage rating, as this could lead to a circuit overload, ultimately resulting in a fire in the vehicle.< A pair of plastic tweezers and instructions for fuse allocation is stored with the fuses in the cargo bay. Spare fuses can be obtained from your BMW Sports Activity Vehicle.
In interior The fuses are located in the front passenger footwell on the underside of the instrument cluster. 1. Unscrew screws, refer to arrows, of footwell
trim panel.
2. Lay the trim panel in the footwell. 3. Unscrew the screw, arrow 1, and fold down
the fuse carrier, arrow 2.
4. Replace the fuse concerned. 5.
Installation is carried out in the reverse order of removal. Ensure correct and secure attachment of the footwell trim panel in the process.
259
ba8_e70ag.book Seite 260 Freitag, 5. Juni 2009 11:42 11
In cargo bay
Open the right-hand side panel in the cargo bay.
260
ba8_e70ag.book Seite 261 Freitag, 5. Juni 2009 11:42 11
Giving and receiving assistance
Emergency request Conditions for an emergency request: > Full preparation package mobile phone.
With this equipment, an emergency request is still possible when no mobile phone is paired in the vehicle.
> BMW Assist is activated.
Activating BMW Assist, refer to page 215.
> Radio readiness is switched on. > The BMW Assist system is logged in on a
wireless communications network.
> The emergency request system is opera-
ble.
When the contract of participation with BMW Assist expires, the BMW Assist system can be deactivated by a BMW Sports Activity Vehicle Center without having to visit a workshop. Once the BMW Assist system has been deactivated, emergency requests are not possible. The BMW Assist system be reactivated by a BMW Sports Activity Vehicle Center after signing a new contract.
Initiating an emergency request 1. Briefly press protective cover to open.
Depending on the vehicle's equipment, the arrangement of the switches and indicator lamps may differ somewhat.
2. Press the SOS button until the LED in the
button lights up.
As soon as the voice connection to the BMW Assist Response Center has been established, the LED flashes. When the emergency request is received at the BMW Assist Response Center, the BMW Assist Response Center contacts you and takes fur- ther steps to help you. Even if you are unable to answer, the BMW Assist Response Center can take further steps to help you under certain conditions. If conditions allow, remain in the vehicle until the connection has been established. You will then be able to provide a detailed description of the situation. Information for determining the required rescue measures is transmitted to the BMW Assist Response Center, e.g. the current position of your vehicle, if this can be determined. If the LED flashes, but you are unable to hear the BMW Assist Response Center through the hands-free system, this could indicate, for instance, that the hands-free system is no longer operational. The BMW Assist Response Center may still be able to hear you, however. Under certain conditions, an emergency request is automatically initiated immediately after a severe accident. An automatic collision notification is not affected by the button being pressed.
For technical reasons, the emergency request cannot be guaranteed under
unfavorable conditions.<
Warning triangle* The warning triangle is located in the cargo bay.
261
ba8_e70ag.book Seite 262 Freitag, 5. Juni 2009 11:42 11
First-aid kit* Some of the articles contained in the first-aid kit have a limited service life. Therefore, check the expiration dates of the contents regularly and replace the contents concerned in good time if necessary. The first-aid kit is stored in the cargo bay, depending on the vehicle's equipment, > on the right in a storage tray or > behind the left side panel
Roadside Assistance* The BMW Roadside Assistance offers you assistance in the event of a breakdown around the clock, including on weekends and public holidays. The phone numbers of the Roadside Assis- tance in your home country can be found in the Contact brochure. With BMW Assist or BMW TeleServices, you can contact BMW Roadside Assistance directly via iDrive to request assistance in the event of a breakdown, refer to page 216.
Jump starting When your battery is discharged, you can use two jumper cables to start your BMW with power from the battery in a second vehicle. You can also use the same method to help start another vehicle. Use only jumper cables with fully-insulated clamp handles.
To avoid the risk of potentially fatal injury, always avoid all contact with electrical
components while the engine is running. Care- fully adhere to the following sequence, both to prevent damage to one or both vehicles, and to guard against possible personal injuries.<
262
Preparation 1. Check whether the battery of the other
vehicle has a voltage of 12 Volts and approximately the same capacitance in Ah. This information can be found on the bat- tery.
2. Switch off the engine of the assisting vehi-
cle.
3. Switch off any electrical systems and com-
ponents in both vehicles.
There must not be any contact between the bodies of the two vehicles, otherwise
there is a danger of shorting.<
Connecting jumper cables
To avoid personal injury from sparks, fol- low this sequence when connecting
jumper cables.< On your BMW the so-called starting-aid termi- nal in the engine compartment acts as the bat- tery positive terminal, also refer to the engine compartment overview on page 240. The cover cap is marked with +. 1. Fold open the cover of the BMW starting-
aid terminal. To do so, pull the tab.
2. Attach one end of the jumper cable plus/+ to the positive terminal of the battery or a starting-aid terminal of the vehicle provid- ing assistance.
3. Attach the second end of the cable to the
positive terminal of the battery or to a start- ing-aid terminal of the vehicle to be started. 4. Attach one end of the jumper cable minus/– to the negative terminal of the battery or to an engine or body ground of the assisting vehicle.
ba8_e70ag.book Seite 263 Freitag, 5. Juni 2009 11:42 11
Your BMW has a special nut as body ground or negative pole.
It is located in the toolkit under the floor panel flap in the cargo bay, refer to page 250.
Use only the tow fitting provided with the vehicle and screw it all the way in. Use the tow fitting for towing only on roads. Avoid lateral loading of the tow fitting, e.g. do not lift the vehi- cle by the tow fitting. Otherwise damage to the tow fitting and the vehicle can occur.<
Access to screw thread Cover panel on left and right side of bumper: press on the arrow symbol on the cover panel.
Front
Rear
Being towed
Make sure that the ignition is switched on, refer to page 59, otherwise the low
beams, tail lamps, turn signals and windshield wipers would not be available. When the engine is stopped, there is no power assist. This then requires increased effort for braking and steer- ing. Active steering is deactivated and larger steering wheel movements are required.< Switch on the hazard warning flashers depend- ing on the local regulations. If the electrical sys-
263
5. Attach the second end of the cable to the negative terminal of the battery or to the engine or body ground of the vehicle to be started.
Starting engine 1. Start the engine on the assisting vehicle
and allow it to run at idle for several minutes at slightly increased speed.
2. Start the engine on the other vehicle in the
usual way. If the first starting attempt is not successful, wait a few minutes before another attempt in order to allow the discharged battery to recharge.
3. Let the engines run for a few minutes. 4. Disconnect the jumper cables by reversing
the connection sequence.
Check the battery and recharge if necessary.
Never use spray fluids to start the engine.<
Tow-starting and towing
Observe applicable laws and regulations for tow-starting and towing.< Do not transport any passengers other than the driver in a vehicle that is being
towed.<
Using a tow fitting The screw-on tow-fitting must always be car- ried in the vehicle. It can be screwed in at the front or rear of the BMW.
ba8_e70ag.book Seite 264 Freitag, 5. Juni 2009 11:42 11
tem fails, mark the vehicle to be towed, e.g. with a sign or warning triangle in the rear window.
attachment to other vehicle parts can lead to damage.<
With tow truck
Do not tow your BMW with the front or rear axle raised individually; otherwise,
the wheels may lock and the transfer case may be damaged.<
Have the BMW transported only on a flatbed surface.
Tow-starting The engine cannot be started by tow-starting. Start the engine by jump starting it, refer to page 262. Have the cause of the starting difficulties elimi- nated.
Before towing, manually unlock the trans- mission lock, refer to page 66; failure to
do so can result in damage to the transmis- sion.<
Do not exceed a towing speed of 45 mph/ 70 km/h and a towing distance of
90 miles/150 km, otherwise the automatic transmission may be damaged.<
Towing methods
Do not lift vehicle by tow fitting or body and chassis parts, otherwise damage may
result.< In some countries, towing with tow bars or ropes in public traffic is not permitted. Familiar- ize yourself with the regulations on towing in the respective country.
With tow bar
The towing vehicle may not be lighter than the vehicle to be towed, otherwise it
will not be possible to reliably control vehicle response.< The tow fittings used should be on the same side on both vehicles. Should it prove impossi- ble to avoid mounting the tow bar at an offset angle, observe the following: > Clearance and maneuvering capability will
be sharply limited during cornering.
> When mounted at an angle, the tow bar will
exert lateral forces, tending to push the vehicle sideways.
Only attach the tow bar to the tow fittings, as attachment to other vehicle parts can
lead to damage.<
With tow rope When starting off in the towing vehicle, make sure that the tow rope is taut.
To avoid jerking and the associated stresses on vehicle components when
towing, always use nylon ropes or nylon straps. Only attach tow ropes to the tow fittings, as
264
ba8_e70ag.book Seite 265 Freitag, 5. Juni 2009 11:42 11
265
ba8_e70ag.book Seite 266 Freitag, 5. Juni 2009 11:42 11
ba8_e70ag.book Seite 267 Freitag, 5. Juni 2009 11:42 11
Reference Reference
This chapter contains the technical data, the short commands of the voice activation system, and the index that will direct you as quickly as possible to the information you are looking for.
ba8_e70ag.book Seite 268 Freitag, 5. Juni 2009 11:42 11
Technical data
Engine data
BMW X5
Displacement No. of cylinders Maximum output at engine speed Maximum torque at engine speedBMW X6
Displacement No. of cylinders Maximum output at engine speed Maximum torque at engine speedcu in/cmμ
hp rpm lb ft/Nm rpm
cu in/cmμ
hp rpm lb ft/Nm rpm
X5 xDrive30i 182.8/2,996
260
6,600
225/305
2,750X5 xDrive48i 292.9/4,799
350
6,300
350/475
3,400-3,800X6 xDrive35i 181.8/2,979
300
5,800-6,250
300/407
1,400-5,000X5 xDrive35d 182.6/2,993
265
4,200
425/580
1,750-2,250X6 xDrive50i 268.2/4,395
400
5,500-6,400
450/610
1,750-4,500268
ba8_e70ag.book Seite 269 Freitag, 5. Juni 2009 11:42 11
Dimensions
BMW X5
All dimensions given in inches/mm. Smallest turning circle diam.: 42.0 ft/12.8 m With mixed tires* the vehicle width may exceed the specified dimension.
269
ba8_e70ag.book Seite 270 Freitag, 5. Juni 2009 11:42 11
BMW X6
All dimensions given in inches/mm. Smallest turning circle diam.: 42.0 ft/12.8 m Height with roof rack*: 66.9 in/1,699 mm With mixed tires* the vehicle width may exceed the specified dimension.
270
ba8_e70ag.book Seite 271 Freitag, 5. Juni 2009 11:42 11
Weights
BMW X5
Approved gross vehicle weight without 3rd row seats Load without 3rd row seats Approved front axle weight without 3rd row seats Approved rear axle weight without 3rd row seats Approved roof load capacity Cargo bay capacitylbs./kg lbs./kg lbs./kg lbs./kg lbs./kg lbs./kg lbs./kg lbs./kg lbs./kg cu ft/l
X5 xDrive30i X5 xDrive48i X5 xDrive35d 6,614/3,000
6,327/2,870
6,294/2,855
6,008/2,725
1,290/585
1,290/585
1,102/500
1,102/500
3,064/1,390
2,767/1,255
3,064/1,390
2,778/1,260
3,803/1,725
3,858/1,750
3,395/1,540
3,395/1,540
220/100
220/100
21.9-61.8/ 21.9-61.8/ 620-1,750
620-1,7506,537/2,965
6,173/2,800
