Login- Download PDF Manual
-
could result in damage caused by undesired wiper activation.<
Normal wiper speed When the vehicle is stationary, the wip- ers switch automatically to intermittent wipe – not on vehicles with rain sensor.
0 Wipers retracted 1 Intermittent operation or rain sensor 2 Normal wiper speed 3 Fast wiper speed 4 Brief wipe 5 Rotary dial for control of the wipe
interval or the sensitivity of the rain sensor
Intermittent mode Not on vehicles with rain sensor. You can set the wipe interval at four stages with rotary dial 5. In addition, the wipe interval is varied automatically depending on road speed.
78
Washer/wiper system/Rain sensor*
Cruise control*
When the vehicle's lighting system is switched on, the headlamps will also be cleaned at reasonable intervals.
Windshield washer nozzles The windshield washer nozzles are heated automatically* when the ignition key is in position 2.
Starting at about 20 mph / 30 km/h, you can maintain and store any vehicle speed that you specify. The cruise control is operational when- ever the engine is running and the sys- tem has been activated.
To activate the system
Cleaning windshield and headlamps* 0 Wipers retracted 1 Clean windshield and headlamps*
Do not use the washers if there is any danger that the fluid will
freeze on the windshield, as your vision could be obscured. Always use a wind- shield washer antifreeze in cold weather. Refer to page 132. Do not use the washers when the reser- voir is empty. This could cause damage to the washer pump.<
The system sprays washer fluid against the windshield and activates the wipers for a brief period.
In ignition key position 2: press the but- ton in the steering wheel. The indicator lamp in the instrument cluster comes on, refer to page 20. You can now use the cruise control.
Do not use cruise control on twist- ing roads, when high traffic den-
sity prevents driving at a constant speed, or when the road surface is slick – snow, rain, ice – or loose – rocks or gravel, sand.<
To deactivate the system
Press button as often as you need to until the indicator lamp in the instru- ment cluster goes out. Cruise control is also deactivated when the ignition key is in position 0.
Cruise control*
The speed stored in memory is deleted.
To store and maintain speed or to accelerate
Press button + briefly: The system stores and maintains the current vehicle speed. Every time you tap the button, the speed increases by approx. 0.6 mph / 1 km/h. Press and hold button +: The vehicle accelerates without pres- sure on the accelerator pedal. When you release the button, the system stores and maintains the current speed.
If on a downhill gradient the engine braking effect is not suffi-
cient, the controlled speed can be exceeded. Speed can drop on uphill grades if the engine output is insuffi- cient.<
To decelerate
Press button – briefly: When cruise control is active, every tap of the button reduces the speed by approx. 0.6 mph / 1 km/h.
Press and hold button –: With the cruise control active, the sys- tem automatically reduces the throttle opening to slow the vehicle. When you release the button, the system stores and maintains the current speed.
To interrupt the cruise control
To recall the stored setting
Press button: The vehicle accelerates to and main- tains the last speed stored.
When the system is activated, press the button. The indicator lamp stays on. You can use the cruise control again whenever you want by calling up the speed that was stored last. In addition, cruise control is interrupted automatically: > When the brakes are applied > When you apply pressure to the
clutch pedal, or when you move the automatic transmission selector lever from D to N
> If you exceed or fall below the pro-
grammed speed for an extended period – by depressing the accelera- tor, for example.
79
Everything under control Odometer
80
Tachometer
Energy control
1 Odometer 2 Trip odometer
Odometer You can activate the displays shown in the illustration with the ignition key in position 0 by pressing the left button in the instrument cluster.
Trip odometer To reset the trip odometer to zero, press the left button with the ignition key in position 1 or higher.
Do not operate the engine with the nee- dle in the red overspeed zone of the gauge. To protect the engine, the fuel supply is interrupted when you approach this sector.
Indicates the current fuel consumption in mpg – in liters/100 km on Canadian models. This allows you to see whether your current driving style is conducive to fuel economy with minimum exhaust emissions. When the vehicle is stationary, the dis- play goes to Maximum – zero on Cana- dian models.
Fuel gauge
Engine coolant temperature gauge
81
Once the indicator lamp stays on con- tinuously, there are still approx. 2 gallons/8 liters of fuel in the fuel tank. Fuel tank capacity approx. 16.6 gallons/63 liters. Certain operating conditions, such as those encountered in mountainous areas, may cause the needle to fluctu- ate slightly.
Fill the fuel tank before it is com- pletely empty. Driving to the last
drop of fuel can prevent the engine from operating properly and result in damage.<
When you switch on the ignition, the indicator lamp lights up briefly as an operation check.
Blue The engine is still cold. Drive at moder- ate engine and vehicle speeds.
Between the blue and red zones Normal operating range. The needle may rise as far as the edge of the red sector during normal operation.
Red When you switch on the ignition, the warning lamp comes on briefly as an operation check. If the lamp comes on during normal vehicle operation: the engine has over- heated. Shut off the engine immediately and allow it to cool down. To check coolant level, refer to page 134.
82 Service interval display
Check Control
A flashing message and a '–' in front of the number mean that the service inter- val has already been exceeded by the distance shown on the display. Please contact your BMW center for an appointment.
Remaining distance to next service The displays shown in the illustration appear for a few seconds when the ignition key is in position 1 or higher or after the engine is started. The next service due appears with the message OIL SERVICE or INSPECTION, together with the dis- tance remaining in miles – in kilometers in Canada – before the next scheduled service. The computer bases its calculations of the remaining distance on the preced- ing driving style.
When the ignition key is in position 2, the following information and/or condi- tions are indicated using symbols until the conditions have been corrected. 1 Check the low beam and high beam
headlamps, as well as the parking lamps
2 Door open 3 Luggage compartment lid open 4 Check brake and tail lamps When you open the driver's door after having turned the ignition key to posi- tion 0, you will hear an acoustic signal for a few seconds to remind you that the lamps have not been switched off.
Clock
If you wish to have a permanent time display, you can make this adjustment in the radio display, refer to the Owner's Manual for Radio. You can adjust the clock and the time display in the car radio as follows.
83
Every time you press the button, the clock display alternates between the 12-hour and 24-hour mode. In ignition key position 0: the time is displayed for a few seconds after you press the left button, refer to Odometer on page 80.
Setting
Before the clock can be set, the time must be showing in the
instrument cluster display.<
With the ignition key in position 1 or higher To set ahead: turn the right button to the right. To set back: turn the right button to the left. The adjustment speed will increase the longer you continue to hold the right button. To change the display mode: press the right button briefly.
84 Computer*
After giving an ice warning, the display returns to the previous
setting.<
The ice warning does not alter the fact that surface ice can form at temperatures above 37.57/+36, on bridges or shaded road surfaces, for instance.<
Mode selection With the ignition key in position 1 or higher, you can use the button in the turn signal lever to request information from the computer. Each time you press the button briefly toward the steering column, a new function is called up in the display. The displays appear in the following order: Time of day, outside temperature, aver- age fuel consumption, cruising range, average vehicle speed. With the ignition key in position 1 or higher, the last active setting is dis- played.
Outside temperature You can change the units of measure 6/7 for the outside temperature dis- play by pressing the right-hand reset button in the instrument cluster while the temperature display is active. The units of measure 6/7 in the tempera- ture display of the automatic climate control change automatically, see page 102.
Ice warning If the outside temperature drops to about 37.57/+36, then the computer will automatically switch to a display of the outside temperature. In addition, a signal sounds as a warning and the dis- play flashes for a brief period.
It is important that you refuel when the cruising range falls below
approx. 35 miles/50 km. Otherwise, the engine cannot be guaranteed to oper- ate properly and damage may result.<
Average speed If you continue to press and hold the button, the average speed being dis- played is recalculated from that point in time. Any time spent when the vehicle is sta- tionary and the engine is shut off is ignored for the calculation.
Computer*
Average fuel consumption If you continue to press and hold the button on the turn signal lever, the aver- age fuel consumption last displayed is recalculated from that point in time.
If you wish, you can have the aver- age fuel consumption displayed in
a different unit of measure.<
Range The computer bases its calculations for the cruising range on the operating conditions in the preceding period and on the remaining fuel in the tank.
85
Technology for safety and driving convenience Park Distance Control (PDC)*
86
The concept PDC assists you when you back into a parking space. Acoustic signals alert you to the momentary distance to an object behind your vehicle. The system features four ultrasonic sensors mounted in your rear bumper. The mon- itoring range for the two corner sensors extends outward roughly 2 ft/60 cm behind the bumpers, while two centrally located sensors detect objects at dis- tances of up to approx. 5 ft/1.50 m.
PDC is a parking aid that can identify objects if they are
approached slowly, as is generally the case when parking. Avoid driving towards objects rapidly; due to underly- ing physical principles, the system may otherwise alert you too late for you to take evasive steps.<
The system starts to operate automati- cally approx. one second after you shift into Reverse or move the selector lever into the R position with the ignition key in position 2.
Let this short period elapse before driving backwards.<
PDC is deactivated when you shift back out of Reverse.
You can have a signal set to con- firm that the PDC has been acti- vated. The signal then sounds when you shift into Reverse or move the selector lever into the R position.<
Acoustic signals The distance to the nearest object is indicated by a tone sounding at various intervals. As the distance between vehi- cle and object decreases, the intervals between the tones become shorter. A continuous tone indicates the pres- ence of an object less than 1 ft/30 cm away. The warning signal is canceled after approx. three seconds if the distance to the object remains constant during this time – if you are moving parallel to a wall, for instance. System malfunctions will be indicated by a continuous high-pitched tone when the system is activated the first time. Please have the problem fixed by your BMW center.
PDC does not remove the driver's personal responsibility for evaluat-
ing the distance between the vehicle and any objects. Even when sensors are involved, there is a blind spot in which objects cannot be detected. This applies especially in those cases where the system approaches the physical limits of ultrasonic measurement, as occurs with tow bars and trailer cou- plings, and in the vicinity of thin or wedge-shaped objects. Moreover, low objects that have already been detected – such as a curb edge – can disappear out of the detection range of the sensors before a continuous tone sounds. Loud sources of sound from outside or inside the vehicle could drown out the PDC signal tone.<
Keep the sensors clean and free of ice or snow in order to ensure that they will continue to operate effec- tively. Do not apply high pressure spray to the sensors for a prolonged period of time. Always maintain a distance of more than 4 in/10 cm.<
Dynamic Stability Control (DSC)
87
The vehicle will remain completely operational, however, without DSC. In the event of a fault, please consult your BMW center.
Indicator and warning lamps for Canadian models.
The concept DSC maintains vehicle stability, even in critical driving situations. The DSC is operational every time you start the engine. DSC incorporates the Dynamic Traction Control (DTC) and Cornering Brake Control (CBC) functions. For information on vehicles with all- wheel drive, refer to page 89 ff.
Indicator lamps
The indicator lamp in the instru- ment cluster goes out shortly after the ignition has been
switched on; refer to page 19. > The indicator lamp flashes: DSC is
actively controlling drive torque and braking intervention
> The indicator lamp stays lit: DSC has
been switched off with the button; DTC and DBC are operational. DTC control intervention is not indicated.
The indicator lamp and the brake warning lamp continu- ously light up in yellow: The DSC, DTC and DBC have been switched off manually or
there is a system malfunction.
Deactivating the DSC/activating the DTC Press the DSC button briefly; the indi- cator lamp comes on and stays on. DSC is deactivated; DTC is operational. In the following rare situations, it may prove useful to activate the DTC for a brief period: > When rocking the vehicle or starting off in deep snow or on loose surfaces
> When driving on snow-covered
grades, in deep snow, or on a snow- covered surface that has been packed down from being driven on
> When driving with snow chains.
88
Dynamic Stability Control (DSC)
The laws of physics cannot be repealed, even with DSC. An
appropriate driving style always remains the responsibility of the driver. We therefore urge you to avoid using the additional safety margin of the sys- tem as an excuse for taking risks. Whenever the DTC is activated, the DSC is switched off and DTC performs minor stabilizing intervention. Do not make any modifications to the DSC system. Allow only authorized technicians to perform service proce- dures on the DSC.<
Under these special circumstances traction is increased by deactivating the control systems that enhance traction under normal conditions.
Deactivating the DSC and the DTC Press the DSC button down for at least 3 seconds; the indicator lamp and the yellow brake warning lamp will remain on continuously. The systems for enhancing stability and traction are deactivated, and there is no active braking intervention or torque control.
To maintain vehicle stability, always drive with the DSC acti-
vated whenever possible.<
Reactivating the DSC Press the button again briefly; the indi- cator lamp or the indicator lamps will go out. DTC is deactivated.
Dynamic Stability Control (DSC) – 325xi, 330xi
89
The vehicle will remain completely operational, however, without DSC. In the event of a fault, please consult your BMW center.
The concept DSC maintains vehicle stability, even in critical driving situations. The DSC is operational every time you start the engine. DSC includes the Automatic Differential Brake (ADB-X) and Cornering Brake Control (CBC) functions.
Indicator lamps
The indicator lamp in the instru- ment cluster goes out shortly after the ignition has been
switched on; refer to page 19. > The indicator lamp flashes: DSC is
actively controlling drive torque and braking intervention
> The indicator lamp stays lit: DSC has
been switched off with the button; ADB-X is operational. ADB-X control intervention is not indicated.
If the indicator lamp fails to go out when you press the DSC button, this indicates a malfunction in the DSC and ADB-X systems; the system is deactivated, and the stability enhance- ment functions are no longer avail- able.<
To deactivate DSC Press the DSC button; the indicator lamp comes on and stays on. DSC is now off, and ADB-X reverts to its maximum torque-transfer mode. In the following exceptional circum- stances, it may be effective to deacti- vate the DSC for a short period: > When rocking the vehicle or starting off in deep snow or on loose surfaces
> When driving with snow chains.
To maintain vehicle stability, always drive with the DSC acti-
vated whenever possible.<
90
Dynamic Stability Control (DSC) – 325xi, 330xi
Reactivating the DSC Press the button again; the indicator lamp goes out.
The laws of physics cannot be repealed, even with DSC. An
appropriate driving style always remains the responsibility of the driver. We therefore urge you to avoid using the additional safety margin of the sys- tem as an excuse for taking risks. The system does not intervene to enhance vehicle stability when switched off. Do not make any modifications to the DSC system. Allow only authorized technicians to perform service proce- dures on the DSC.<
Hill Descent Control (HDC)*
The concept By reducing the vehicle's speed on steep downhill stretches, HDC main- tains predictable vehicle handling response to provide you with control of your BMW during extreme descents. The vehicle slows to a pace just slightly faster than walking speed. HDC is available for activation at vehi- cle speeds below approx. 22 mph / 35 km/h. When driving down steep hills, the vehicle reduces speed auto- matically down to about double walking speed – approx. 7.5 mph / 12 km/h – and then maintains this speed at a con- stant. You can use the accelerator or brakes to vary this speed within a range from approx. 3 mph / 5 km/h to approx. 15 mph / 25 km/h. In conjunction with the multifunction steering wheel, you can use the +/– button to set the cruise control to a tar- get speed in the range from approx. 3 mph / 5 km/h to approx. 15 mph / 25 km/h. HDC is automatically deactivated once vehicle speed again exceeds approx. 37 mph / 60 km/h.
To activate the system Press the HDC button; the green indi- cator lamp integrated within the button comes on. The indicator lamp flashes whenever the system is actively intervening to control your speed with automatic brake applications.
To deactivate the system Press the button again, the indicator lamp goes out. HDC is automatically deactivated once the vehicle accelerates to more than 37 mph / 60 km/h, as well as whenever you switch off the ignition.
91
To use HDC Vehicles with manual transmission: You should always ensure that either reverse or first gear is engaged before using HDC, as the engine's braking effect is most pronounced in these gears, and only reduced engine braking is available in higher gears. Vehicles with automatic transmission: HDC is available for use in all ranges.
System malfunctions Are signaled by the indicator lamp, which responds to problems by going out while HDC is in operation or by fail- ing to come on when you activate the system: HDC has been temporarily deactivated as a result of high brake temperatures.
If the DSC indicator lamp comes on at the same time: Malfunction in HDC and DSC
system. Refer the problem to your BMW center.
92 Flat Tire Monitor*
The concept As you drive, the Flat Tire Monitor keeps track of pressure levels in all four tires. The system alerts you whenever the inflation pressure of a tire falls sig- nificantly below the pressure of another tire. The system actually detects pressure loss by monitoring differences in the relative speeds of the four wheels. It interprets variations outside specified limits as severe pressure loss, and then responds by generating a warning.
Functional requirements In order for the Flat Tire Monitor to learn the correct tire inflation pressure, please do the following: 1. Check the tire inflation pressures in
all tires
2. Compare them with the tire inflation pressure table on page 26 and cor- rect them, if necessary
3. Initialize the system.
System limitations
The Flat Tire Monitor cannot pro- vide you with advance warning of sudden and severe tire damage caused by external factors and does not detect the balanced and very gradual pressure loss that takes place in all four tires over an extended period of time.<
On the other hand, the following situa- tions can lead to a delayed detection of pressure loss and even to the system not functioning: > Driving on snow-covered or slippery
roads
> Performance-oriented driving: slip at the drive wheels, high levels of lateral acceleration
> When driving with snow chains, false
warnings and undetected pressure losses may occur
> When driving with a space-saver
spare tire, the Flat Tire Monitor can- not function.
Initializing the system
Each time you correct the pres- sure in a tire, or change a wheel or tire, reinitialize the system immediately afterwards. This requires a bit of driv- ing.<
1. Before driving off, start the engine
but do not start driving
2. Press the button as long as you need
to until the yellow indicator lamp in the instrument cluster lights up for a few seconds
3. Drive off. It takes a few minutes before the Flat Tire Monitor can detect a flat tire and issue a warning.
Flat Tire Monitor*
When driving with snow chains or a space-saver spare tire, do not
initialize the system.<
Flat tire
The indicator lamp in the instru- ment cluster lights up red. This visual alert is accompanied by
an acoustic warning signal. 1. Carefully reduce speed and come to
a stop. Avoid sudden braking and steering maneuvers
2. Determine which wheel is damaged
If this cannot be determined, con- tact your BMW center.<
Because the sides of Run Flat tires are reinforced, a drop in infla-
tion pressure usually cannot be detected from the outside, refer to Run Flat tires, page 150.<
2. To continue driving, follow the
instructions under Driving with a damaged tire on page 151.
System malfunction
The indicator lamp in the instru- ment cluster lights up yellow. The Flat Tire Monitor is malfunc- tioning or out of order. Please refer the problem to your BMW center.
Brake force display
93
The brake force display indicates to the driver of the vehicle behind you how hard you are braking your vehicle. The display has two levels: > Normal braking: the brake lamps
among the rear lamps and the center brake lamp light up
> Hard braking or use of ABS: the tail lamps light up with the same bright- ness as the brake lamps and thereby intensify the visual effect of the brake lamps.
3. Replace the damaged wheel, refer to
Changing a wheel on page 147.
After replacing the damaged tire, initial- ize the system. Vehicles with Run Flat tires: 1. Carefully reduce your speed to under
50 mph / 80 km/h. Avoid strong braking and steering maneuvers. Do not exceed a speed of 50 mph / 80 km/h.
Lamps Parking lamps/Low beams
94
Follow me home lamps When you activate the headlamp flasher after parking the vehicle with the lamps turned off, the low-beam head- lamps will come on for a short time.
You can also have this function deactivated.<
LIGHTS ON warning When you open the driver's door after having turned the ignition key to posi- tion 0, you will hear an acoustic signal for a few seconds to remind you that the lamps have not been switched off.
Daytime driving lamps* If you desire, the light switch can be left in the second position: when the igni- tion is switched off, the external lighting is also switched off.
You can have the activation set- tings for the daytime driving lamps
programmed on your vehicle.<
Automatic headlamp control*
When the switch is set to this position, the system automati- cally activates and cancels the low beams in response to changes in ambient light – in tunnels, at dusk, etc. – and in the event of rain and snow.
The vehicle's external lights remain on constantly when you
switch on the front fog lamps after the headlamps have come on automati- cally.<
Automatic headlamp control can- not serve as a substitute for the
driver's judgement in determining when the vehicle lights should be switched on. For example, the sensors are not able to detect fog. To avoid safety risks, you should respond to these kinds of low-visibility situations by switching the headlamps on manually.<
You can have the sensitivity of your vehicle's automatic head-
lamp control adjusted.<
Parking lamps
The front, rear and side vehicle lighting is switched on. You can use the parking lamps to signal
the position of the vehicle when it is parked. For lighting on one side for parking as an additional feature, refer to page 95.
Low beams
When the ignition is switched off while the low beams are on, the headlamps go out and only the
parking lamps remain on.
Instrument lighting
High beams/Standing lamps
95
Turn the rotary dial to adjust the illumi- nation intensity.
1 High beams – blue indicator lamp 2 Headlamp flasher – blue indicator
lamp
3 Parking lamps
Standing lamps, left or right As an additional feature, you can illumi- nate your vehicle on either side for parking: With the ignition key in position 0, engage the lever in the appropriate turn-signal position.
96 Fog lamps*
Interior lamps
Front fog lamps
The green indicator lamp in the instrument cluster lights up to indicate that the front fog lamps
are on.
If the automatic headlamp control is on, the low beams will come on
automatically whenever you activate the front fog lamps.<
The interior lamps operate automati- cally. To switch the interior lamps on and off manually Press button 1 briefly: If you want the interior lamps to remain off all the time, press and hold the but- ton for approx. 3 seconds. Press the button briefly to revert to nor- mal operation.
Front reading lamps* Switch on and off with the button 2 adjacent to each lamp.
Rear reading lamps Switch on and off with the button adja- cent to each lamp.
In order to prevent battery dis- charge, all of the lamps in the
vehicle are automatically switched off approx. 15 minutes after you turn the ignition key to position 0.<
Light-emitting diodes Light-emitting diodes (LEDs) installed behind translucent lenses serve as the light sources for many of the controls and displays in your vehicle. These light-emitting diodes are related to con- ventional lasers, and legislation defines them as light-emitting diodes, Class 1.
Interior lamps
Do not remove the protective lens and avoid staring directly at the unfiltered beam for several hours, as inflammation of the retina could result.<
97
Controlling the climate for pleasant driving Air conditioning
98
Air conditioning
1 Air onto the windshield and the side
windows
2 Air for the upper body area 101
3 Air to the footwell 4 Air supply/Blower 100
5 Temperature 100
6 Air distribution 100
7 Rear window defroster 100
8 Air conditioning 100
9 Outside air/Recirculated-airmode 100
99
Outside air/Recirculated-air mode You can respond to unpleasant external odors by temporarily
blocking the supply of outside air. The system then recirculates the air cur- rently within the vehicle.
If the windows should fog over in the recirculated-air mode, switch this mode off and increase the air sup- ply as required.<
100
Air conditioning
Air supply/Blower
Rear window defroster
You can select blower speeds from 1 to 4. The heating and ventilation become more and more effective as the air sup-
When the rear window defroster is activated, the indicator lamp comes on. The rear window defroster switches off automatically.
ply settings are increased. In position 0, the blower and the heater are switched off. The outside air supply is blocked in position 0.
Temperature
In order to increase the tem- perature of the passenger compartment, turn to the right toward the red zone. The tem- perature of the incoming air is kept con- stant.
Air distribution
You can direct air to flow onto , toward your the windows upper body or into the footwell
. All intermediate
settings are possible. In the setting there is a low flow of air onto the win- dows to keep them free of condensa- tion.
You can have your vehicle pro- grammed in such a way that the
rear window defroster switches on automatically. This occurs within 5 min- utes after starting the engine when out- side temperatures are below approx. 397/+46.<
Air conditioning
The air is cooled and dehumidi- fied and – depending on the
temperature setting – rewarmed. Depending on the weather, the wind- shield may fog over briefly when the engine is started. Air conditioning helps prevent the windows from fogging up.
Condensation forms during opera- tion of the air conditioning system,
which then exits under the vehicle. Traces of condensed water of this kind are thus normal.<
Air conditioning
101
Microfilter The built-in microfilter removes dust and pollen from the incoming air. Your BMW center will replace it during rou- tine maintenance. A substantial reduc- tion in airflow indicates that the filter needs to be replaced before scheduled maintenance.
Draft-free ventilation You can adjust the blower controls for the upper body area to obtain the opti- mum airflow rates and directions for your personal requirements: 1 Rotary dials for infinitely variable
opening and closing of the vent out- lets
2 Levers for airflow direction 3 Rotary dial allows you to control the temperature of the airflow from these outlets as desired
To defrost windows and remove condensation 1. Set the blower speed control for the
air supply to position 4
2. Turn the rotary temperature control
completely to the right to the red zone
3. Turn the rotary control for air distri-
bution to position
4. Switch on the rear window defroster
to defrost the rear window.
102 Automatic climate control*
Automatic climate control*
1 Air onto the windshield and the side
windows
2 Air for the upper body area 105
3 Air to the footwell 4 Air inlet for interior temperature sensor – please keep clear and unobstructed5 Outside air/Automatic recirculated-
air control (AUC)/Recirculated air 105
6 Automatic air distribution and
supply 104
7 Individual air distribution 104
8 Temperature 104
9 Display for temperature 104and air supply 104
10 Air supply/Blower 104
11 To defrost windows and removecondensation 104
12 Air conditioning 104
13 Rear window defroster 105103
104
Automatic climate control*
Tips for pleasant driving Use the automatic mode – switch on with AUTO button 6. Select the desired interior temperature. Detailed setting options are described for you in the following section.
You can make the settings of your vehicle in such a manner that,
when you unlock the vehicle with the remote control of your personal key, your own personalized setting for the automatic climate control is initiated.<
Automatic air distribution and supply
The AUTO program adjusts the air distribution and the air sup- ply for you and in addition adapts the temperature to external influences – summer, winter – to meet preferences you can specify.
, toward the upper , and into the footwell
vated, the automatic airflow control remains in operation. Air flows onto the windows body You can reactivate the automatic air distribution mode by selecting the AUTO button.
Temperature
The interior temperature that appears in the display panel is a general figure intended for refer- ence purposes. We recommend 727/ +226 as a comfortable setting, even if the air conditioning is on. When you start the vehicle, the system ensures that the selected temperature is achieved as quickly as possible. It then maintains this temperature, regardless of the season. To select the units of measure, 6 or 7, for the display, refer to page 84.
Individual air distribution
Air supply/Blower
You can cancel the AUTO pro- gram by selecting specific dis- tribution patterns to suit your own individual requirements.
While the AUTO program is then deacti-
By pressing the upper or lower button, you can vary the air sup- ply. This deactivates the auto-
matic control of the air supply, AUTO disappears from the display panel. Nev-
ertheless, the automatic air distribution remains unchanged. You can reactivate the automatic air distribution mode by selecting the AUTO button. When the lowest blower speed is set and you press the lower button, all of the displays are canceled: the blower, heating and air conditioning are switched off. The outside air supply is blocked. You can reactivate the system by pressing any button for the auto- matic climate control.
To defrost windows and remove condensation
This program quickly removes ice and condensation from the
windshield and the side windows.
Air conditioning
The air is cooled and dehumidi- fied and – depending on the
temperature setting – rewarmed. Depending on the weather, the wind- shield may fog over briefly when the engine is started. Air conditioning helps prevent the windows from fogging up.
Automatic climate control*
105
Condensation forms during opera- tion of the air conditioning system,
recirculates the air currently within the vehicle.
which then exits under the vehicle. Traces of condensed water of this kind are thus normal.<
Outside air/Automatic recirculated-air control (AUC)/ Recirculated air
You can respond to unpleasant external odors or pollutants by
temporarily stopping the flow of outside air. The system then recirculates the air currently within the vehicle. Press the button repeatedly to select one of three different operating modes. > Indicator lamps off: outside airflow is
on
> Left indicator lamp on – AUC mode: the system recognizes pollutants in the outside air and blocks the flow of air when necessary. The system then recirculates the air currently within the vehicle. Depending on the air quality, the automatic system then switches back and forth between outside air supply and recirculation of the air within the vehicle
> Right indicator lamp on: the flow of
external air into the vehicle is perma- nently blocked. The system then
If the windows should fog over in the recirculated-air mode, switch this mode off and increase the air sup- ply as required.<
Rear window defroster
When the rear window defroster is activated, the indicator lamp comes on. The rear window defroster switches off automatically.
You can have your vehicle pro- grammed in such a way that the
rear window defroster switches on automatically. This occurs within 5 min- utes after starting the engine when out- side temperatures are below approx. 397/+46.<
Draft-free ventilation You can adjust the blower controls for the upper body area to obtain the opti- mum airflow rates and directions for your personal requirements: 1 Rotary dials for infinitely variable
opening and closing of the vent out- lets
2 Levers for airflow direction 3 Rotary dial allows you to control the temperature of the airflow from these outlets as desired
106
Automatic climate control*
Roller sun blind*
Microfilter/activated-charcoal filter The built-in microfilter removes dust and pollen from the incoming air. The activated-charcoal filter provides addi- tional protection by filtering gaseous pollutants from the outside air. Your BMW center replaces this combined fil- ter as a standard part of your scheduled maintenance. A substantial reduction in airflow indicates that the filter needs to be replaced before scheduled mainte- nance.
To actuate, press the button briefly with the ignition key in position 1 or higher. The illustration depicts the arrangement of the buttons if the vehicle is fully equipped. The arrangement may vary depending on the equipment actually installed.
Interior conveniences Premium sound system*
Glove compartment
107
Harman Kardon premium sound system Press the button to activate and deacti- vate the acoustic enhancement. The system creates the acoustic impression of a much larger passenger compartment accompanied by improved stereophonic sound at all seating positions. The system responds to poor reception conditions by repeatedly alternating between the stereo and monophonic modes. You should then switch the sys- tem off.
To open Pull the handle. The lamp in the glove compartment comes on.
To close Fold the cover up.
To prevent injury in the event of an accident, close the glove com-
partment immediately after use.<
To lock Lock with one of the master keys. A master key will also be required to unlock the glove compartment.
108
Glove compartment
Storage compartments
If – for example for valet parking – you turn over only your spare key,
refer to page 32, then access to the locked glove compartment is not possi- ble.<
Rechargeable flashlight The flashlight is located on the left side of the glove compartment. It features integral overload-protection, so it can be left in its holder continu- ously.
To avoid completely discharging and possibly damaging the flash- light, always ensure that it is switched off before inserting it in the socket.<
Beverage holders, coin box A coin box and two beverage holders are provided in the center console.
Front center armrest To open: press the button and fold up.
Additional compartments and nets* You will find additional storage com- partments in the front doors and in the center console. Storage nets are on the front seat backrests.
Storage compartments
109
Rear center armrest* Without through-loading system: The rear center armrest includes a stor- age compartment, a beverages holder and a litter bag holder. 1 Storage compartment: pull up 2 Beverages holder: press
Rear center armrest* With through-loading system: The rear center armrest includes a bev- erages holder and a litter bag holder. > Beverages holder: press
Storage package* For your convenience, there are: > Two flip-out sockets on the rear cen-
ter console
> An eyeglasses compartment*, not shown, in the front center console.
110 Cellular phone*
Ashtray, front*
Cigarette lighter socket Suitable for attaching power supplies for flashlights, car vacuum cleaners, etc., up to a rating of approx. 200 watts at 12 volts. Avoid damage to the socket caused by inserting plugs of different shapes or sizes.
Hands-free system On vehicles that are wired for a tele- phone* or equipped with a communica- tions package*, the cover for the hands-free microphone is located in the headliner near the interior lamp. For further information on using your
