Login- Download PDF Manual
-
Top View
Cameras
The lenses of the Top View cameras are located at the bottom of the exterior mirror housings. The image quality may be impaired by dirt. Clean the lens, refer to page 216.
Switching on/off Switching on automatically Select transmission position R with the engine running.
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
129
Controls
Driving comfort
The Top View and PDC images are displayed if the system is switched on via iDrive. Automatic deactivation during forward travel The system switches off when a certain driving distance or speed is exceeded. Switch the system back on if necessary. Switching on/off manually
Press the button.
▷ On: the LED lights up. ▷ Off: the LED goes out. Top View is displayed, switch on the backup camera via the iDrive, refer to page 130. Switching on the backup camera via the iDrive With Top View switched on:
"Rear view camera"
The backup camera image is displayed. The set‐ ting is stored for the remote control currently in use. Display Visual warning The approach of the vehicle to an object can be shown on the Control Display. When the distance to an object is small, a red bar is shown in front of the vehicle, as it is in the PDC display.
The display appears as soon as Top View is ac‐ tivated. If the backup camera image was selected last, it again appears on the display when reverse gear is selected. To switch to Top View:
"Rear view camera" Select the symbol on
the Control Display. The setting is stored for the remote control cur‐ rently in use. Brightness With Top View switched on: 1. 2. Turn the controller until the desired setting
"Brightness"
is reached and press the controller.
Contrast With Top View switched on: 1. 2. Turn the controller until the desired setting
"Contrast"
is reached and press the controller. Displaying the turning circle and pathway lines ▷ The static, red turning circle line shows the
space needed to the side of the vehicle when the steering wheel is turned all the way.
▷ The variable, green pathway line assists you in assessing the amount of space actually needed to the side of the vehicle.
130
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
Driving comfort
Controls
The pathway line is dependent on the cur‐ rent steering angle and is continuously ad‐ justed with the steering wheel movement.
At a glance Button in the vehicle
"Parking aid lines"
Turning circle and pathway lines are displayed. System limits Top View cannot be used in the following situa‐ tions: ▷ With a door open. ▷ With the trunk lid open. ▷ With an exterior mirror folded in. ▷ In poor light. A Check Control message is displayed in some of these situations.
Side View The concept Side View provides an early look at cross traffic at blind driveways and intersections. Road users concealed by obstacles to the left and right of the vehicle can only be detected relatively late from the driver's seat. To improve visibility, two cameras in the front of the vehicle record the traffic situation on each side. Notes The images from both cameras are shown si‐ multaneously on the Control Display.
Check the traffic situation as well Check the traffic situation around the ve‐ hicle on blind driveways and intersections with your own eyes. Otherwise, an accident could re‐ sult from road users or objects located outside the picture area of the Side View cameras.◀
Side View
Cameras
Two cameras integrated in the bumpers capture the image. The two camera lenses are located on the sides of the bumper. The image quality may be impaired by dirt. Clean the lens, refer to page 216.
Switching on/off Switching on/off manually
Press the button.
Automatic deactivation during forward travel The system switches off when a certain driving distance or speed is exceeded.
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
131
Controls
Driving comfort
Switch the system back on if necessary. Display The traffic area to the left and right is displayed on the Control Display.
Head-up Display The concept
Guidelines at the bottom of the image show the position of the front of the vehicle.
Brightness With the Side View switched on: 1. 2. Turn the controller until the desired setting
"Brightness"
is reached and press the controller.
Contrast With the Side View switched on: 1. 2. Turn the controller until the desired setting
"Contrast"
is reached and press the controller.
System limits The cameras capture a maximum range of 330 ft/100 m.
This system projects important information into the driver's field of vision, e.g., the speed. In this way, the driver can get information with‐ out averting his or her eyes from the road.
Display visibility The visibility of the displays in the Head-up Dis‐ play is influenced by: ▷ Certain sitting positions. ▷ Objects on the cover of the Head-up Dis‐
play.
▷ Sunglasses with certain polarization filters. ▷ Wet roads. ▷ Unfavorable light conditions. If the image is distorted, check the basic set‐ tings. Switching on/off 1. "Settings" 2. "Head-up display" 3. "Head-up display"
Switch the Head-up Display ON/OFF as re‐ quired. Display Overview ▷ Speed. ▷ Navigation system.
132
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
▷ Check Control messages. ▷ Collision warning. ▷ Speed limit detection. ▷ Cruise control. ▷ Selection list from the instrument cluster. Some of this information is only displayed briefly as needed. Selecting displays in the Head-up Display 1. "Settings" 2. "Head-up display" 3. "Displayed information" 4. Select the desired displays in the Head-up
Display.
The settings are stored for the remote control currently in use. Setting the brightness The brightness is automatically adjusted to the ambient light. The basic setting can be adjusted manually. 1. "Settings" 2. "Head-up display" 3. "Brightness" 4. Turn the controller.
The brightness is adjusted.
When the low beams are switched on, the brightness of the Head-up Display can be addi‐ tionally influenced using the instrument lighting, refer to page 90. The setting is stored for the remote control cur‐ rently in use. Adjusting the height 1. "Settings" 2. "Head-up display" 3. "Height" 4. Turn the controller.
The height is adjusted.
Driving comfort
Controls
The setting is stored for the remote control cur‐ rently in use. Setting the rotation 1. "Settings" 2. "Head-up display" 3. "Rotation" 4. Turn the controller.
Rotation is set.
The setting is stored for the remote control cur‐ rently in use. Special windshield The windshield is part of the system. The shape of the windshield makes it possible to display a precise image. A film in the windshield prevents double images from being displayed. Therefore, have the special windshield replaced by a service center only.
Parking assistant The concept
This system assists the driver in parking parallel to the road. Ultrasound sensors measure parking spaces on both sides of the vehicle. The parking assistant calculates the best pos‐ sible parking line and takes control of steering during the parking procedure.
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
133
Controls
Driving comfort
A component of the parking assistant is the PDC Park Distance Control, refer to page 124. Notes
Personal responsibility The parking assistant does not relieve the driver of responsibility for the vehicle during the parking procedure. Watch the parking space and parking procedure closely and intervene if necessary; otherwise, there is the danger of an accident.◀ Changes to the parking space Changes to the parking space after it was measured are not taken into account by the sys‐ tem. Therefore, always be alert and ready to inter‐ vene; otherwise, there is the danger of an acci‐ dent occurring.◀
Transporting loads Loads that extend beyond the perimeter of the vehicle are not taken into account by the system during the parking procedure. Therefore, always be alert and ready to inter‐ vene; otherwise, there is the danger of an acci‐ dent occurring.◀
Curbs The parking assistant may steer the vehi‐
cle over or onto curbs. Therefore, always be alert and ready to inter‐ vene; otherwise, the wheels, tires, or the vehicle may become damaged.◀ An engine that has been switched off by the Auto Start Stop function is restarted automati‐ cally when the parking assistant is activated. Requirements For measuring parking spaces ▷ Maximum speed while driving forward ap‐
prox. 22 mph/35 km/h.
▷ Maximum distance to row of parked vehi‐
cles: 5 ft/1.5 m.
▷ When parking in parking spaces on the driv‐ er's side, the corresponding turn signal must be set.
Suitable parking space ▷ Gap between two objects with a minimum
length of approx. 5 ft/1.5 m.
▷ Minimum length of the gap: own vehicle's
length plus approx 4 ft/1.2 m.
▷ Minimum depth: approx. 5 ft/1.5 m. For parking procedure Closed doors. At a glance Button in the vehicle
Parking assistant
Ultrasound sensors
The ultrasound sensors for measuring parking spaces are located on the wheel arches.
134
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
Driving comfort
Controls
System status
The status is displayed with symbols.
Gray: parking space search. Blue: the system is activated. A suitable parking space was found.
The parking procedure is active. Steering control has been seized.
Status of the parking space search
To ensure full operability: ▷ Keep the sensors clean and free of ice. ▷ When using high-pressure washers, do not spray the sensors for long periods and main‐ tain a distance of at least 12 in/30 cm.
Switching on/off Switching on with the button
Press the button. The LED lights up.
The current status of the parking space search is indicated on the Control Display.
Parking assistant is activated automatically.
Switching on with reverse gear Shift into reverse. The current status of the parking space search is indicated on the Control Display. Activate: symbol in the Control Display. Switching off The system can be deactivated as follows: ▷
"Parking Assistant" Select the
Press the button.
▷ Switch off the ignition. Display on the Control Display Activating/deactivating the system
Symbol Meaning
Gray: the system is not available. White: the system is available but not activated. The system is activated.
▷ Gray, arrow 1: parking space search. ▷ Blue, arrow 2: parking space is suitable.
The vehicle is parked in the parking space if the parking procedure is active.
▷ No display: no parking space search.
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
135
Controls
Driving comfort
Parking using the parking assistant
Check the traffic situation as well Loud sounds outside and within the vehi‐ cle can drown out the signal tones of the parking assistant and PDC. Check the traffic situation around the vehicle with your own eyes; otherwise, there is the dan‐ ger of an accident.◀ 1. Switch on the parking assistant and activate
it if necessary. The status of the parking space search is in‐ dicated on the Control Display.
2. Follow the instructions on the Control Dis‐
play. To achieve the best possible parking posi‐ tion, wait for the automatic steering wheel movement after the gear change when the vehicle is stationary. The end of the parking procedure is indi‐ cated on the Control Display.
3. Adjust the parking position yourself if nec‐
essary.
Interrupting manually The parking assistant can be interrupted at any time: ▷
"Parking Assistant" Select the symbol on
the Control Display.
▷
Press the button.
Interrupting automatically The system is interrupted automatically in the following situations: ▷ If the driver grasps the steering wheel or if
he takes over steering.
▷ If a gear is selected that does not match the
instruction on the Control Display.
▷ If a turn signal is activated in the opposite direction to the desired side for parking.
▷ If the vehicle speed exceeds approx.
6 mph/10 km/h.
▷ On snow-covered or slippery road surfaces
if necessary.
▷ If doors are open. ▷ If the Park Distance Control PDC displays
clearances that are too small.
▷ If a maximum number of parking attempts or
the time taken for parking is exceeded.
A Check Control message is displayed. Continuing An interrupted parking procedure can be con‐ tinued if necessary. Follow the instructions on the Control Display to do this. System limits No parking assistance The parking assistant does not offer assistance in the following situations: ▷ In tight curves. Functional limitations The system may not be fully functional in the following situations: ▷ When sensors are dirty or iced over. ▷ In heavy fog, rain or snowfall. ▷ On bumpy road surfaces such as gravel
roads.
▷ When leaves or snow has collected in the
parking space.
Limits of ultrasonic measurement The detection of objects can reach the physical limits of ultrasonic measurement, e.g. in the fol‐ lowing circumstances: ▷ With tow bars and trailer hitches. ▷ With thin or wedge-shaped objects.
136
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
Driving comfort
Controls
▷ With elevated, protruding objects such as
ledges or cargo.
▷ With objects with corners and sharp edges. ▷ With objects with a fine surface structure,
such as fences.
Low objects already displayed, e.g., curbs, can move into the blind area of the sensors before or after a continuous tone sounds. High, protruding objects such as ledges may not be detected. The parking assistant may identify parking spaces that are not suitable for parking. Malfunction A Check Control message is displayed. The parking assistant failed. Have the system checked.
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
137
Controls
Climate control
Climate control Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equipment
Automatic climate control
is also described that is not available in a vehicle, e. g., because of the selected optional equip‐ ment or country variant. This also applies for safety-related functions and systems.
1 Seat heating, left 48
2 Vent settings 3 Rear window defroster 4 Air flow 5 AUTO program6 Temperature 7 Seat heating, right 48
8 Cooling function 9 Recirculated-air mode 10 Interior temperature sensor138
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
Climate control
Controls
Climate control functions in detail Manual air distribution
Turn the wheel to select the de‐ sired program or the desired in‐ termediate setting.
The cooling function, refer to page 139, is switched on automatically with the AUTO pro‐ gram. Temperature
Turn the wheel to set the desired temperature.
▷ ▷ ▷
Windows. Upper body region. Windows, upper body region, and foot‐
well.
Footwell.
▷ Defrosting windows and removing condensation Direct the air distribution toward windows, in‐ crease the air flow and temperature, and, if nec‐ essary, use the cooling function. Rear window defroster Press the button. The rear window defroster switches off
automatically after a certain period of time.
Air flow, manual
Press the left or right side of the button: decrease or increase air flow.
The air flow of the air conditioner may be re‐ duced automatically to save battery power. AUTO program
Press the button. Air flow, air distribution, and tempera‐
ture are controlled automatically. Depending on the selected temperature and outside influences, the air is directed to the windshield, side windows, upper body, and into the footwell.
The automatic climate control reaches this tem‐ perature as quickly as possible, if necessary by increasing the cooling or heating output, and then keeps it constant. Avoid rapidly switching between different tem‐ perature settings. The automatic climate control will not have sufficient time to adjust the set temperature. Cooling function The passenger compartment can only be cooled with the engine running.
Press the button. The air is cooled and dehumidified and, depending on the temperature setting, warmed again. Depending on the weather, the windshield may fog up briefly when the engine is started. The cooling function is switched on automati‐ cally with the AUTO program. When using the automatic climate control, con‐ densation water, refer to page 162, develops that exits underneath the vehicle. Recirculated-air mode You can respond to unpleasant odors or pollu‐ tants in the immediate environment by tempo‐ rarily suspending the supply of outside air. The system then recirculates the air currently within the vehicle.
Press the button repeatedly to select an operating mode:
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
139
Controls
Climate control
▷ LED off: outside air flows in continuously. ▷ LED on, recirculated-air mode: the supply of
outside air into the vehicle is permanently blocked.
If the windows fog over, switch off recirculated- air mode and increase the air volume, if neces‐ sary.
Continuous recirculated-air mode The recirculated-air mode should not be used for an extended period of time, as the air quality inside the vehicle deteriorates steadily.◀
Switching the system on/off Switching off
Press the left button for the minimum speed.
Switching on Press any button except ▷ Rear window defroster. ▷ Seat heating. Microfilter In external and recirculated air mode the micro‐ filter filters dust and pollen out of the air. This filter should be replaced during scheduled maintenance, refer to page 193, of your vehicle.
Automatic climate control with enhanced features
1 Seat heating, left 48
2 Temperature, left 3 AUTO program4 Display 5 Maximum cooling 6 Temperature, right
140
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
Climate control
Controls
7 Seat heating, right 48
8 Cooling function 9 Automatic recirculated-air control/recircu‐lated-air mode
10 Air distribution, right 11 Air flow, AUTO intensity
12 Air distribution, left 13 Rear window defroster 14 Interior temperature sensor — always keep
15 Defrosting windows and removing conden‐
clear
sation
Climate control functions in detail Temperature
Turn the wheel to set the desired temperature.
The automatic climate control reaches this tem‐ perature as quickly as possible, if necessary by increasing the cooling or heating output, and then keeps it constant. Avoid rapidly switching between different tem‐ perature settings. The automatic climate control will not have sufficient time to adjust the set temperature. AUTO program
Press the button. Air flow, air distribution, and tempera‐
ture are controlled automatically. Depending on the selected temperature, AUTO intensity, and outside influences, the air is di‐ rected to the windshield, side windows, upper body, and into the footwell. The cooling function, refer to page 141, is switched on automatically with the AUTO pro‐ gram. At the same time, a condensation sensor con‐ trols the program so as to prevent window con‐ densation as much as possible.
Intensity of the AUTO program With the AUTO program switched on, automatic control of the air flow and air distribution can be adjusted.
Press the left or right side of the button: decrease or increase the intensity.
The selected intensity is shown on the display of the automatic climate control. Maximum cooling
Press the button. The system is set to the lowest tem‐
perature, maximum air flow and recirculated-air mode. Air flows out of the vents for the upper body re‐ gion. Open them for this purpose. The air is cooled fastest when the engine is run‐ ning. The air flow can be adjusted when the program is active. Cooling function The passenger compartment can only be cooled with the engine running.
Press the button. The air is cooled and dehumidified and, depending on the temperature setting, warmed again. Depending on the weather, the windshield may fog up briefly when the engine is started. The cooling function is switched on automati‐ cally with the AUTO program.
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
141
Controls
Climate control
When using the automatic climate control, con‐ densation water, refer to page 162, develops that exits underneath the vehicle. Automatic recirculated-air control/ recirculated-air mode You can respond to unpleasant odors or pollu‐ tants in the immediate environment by tempo‐ rarily suspending the supply of outside air. The system then recirculates the air currently within the vehicle.
Press the button repeatedly to select an operating mode:
▷ LEDs off: outside air flows in continuously. ▷ Left LED on, automatic recirculated-air con‐ trol: a sensor detects pollutants in the out‐ side air and controls the shutoff automati‐ cally.
▷ Right LED on, recirculated-air mode: the
supply of outside air into the vehicle is per‐ manently blocked.
If the windows are fogged over, switch off the recirculated-air mode and press the AUTO but‐ ton to utilize the condensation sensor. Make sure that air can flow onto the windshield.
Continuous recirculated-air mode The recirculated-air mode should not be used for an extended period of time, as the air quality inside the vehicle deteriorates steadily.◀
Manual air distribution
Press the button repeatedly to select a program:
▷ Upper body region. ▷ Upper body region and footwell. ▷ Footwell. ▷ Windows and footwell: driver's side only. ▷ Windows, upper body region and footwell:
driver's side only.
If the windows are fogged over, press the AUTO button to utilize the condensation sensor.
Air flow, manual To be able to manually adjust the air flow, switch off the AUTO program first.
Press the left or right side of the button: decrease or increase air flow.
The selected air flow is shown on the display of the automatic climate control. The air flow of the automatic climate control may be reduced automatically to save battery power. Rear window defroster Press the button. The rear window defroster switches off
automatically after a certain period of time.
Defrosting windows and removing condensation
Press the button. Ice and condensation are quickly re‐ moved from the windshield and the front side windows. The air flow can be adjusted when the program is active. If the windows are fogged over, you can also switch on the cooling function or press the AUTO button to utilize the condensation sensor. Switching the system on/off Switching off
Press the left button for the minimum speed.
Switching on Press any button except ▷ Rear window defroster. ▷ Seat heating.
142
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
Microfilter/activated-charcoal filter In external and recirculated air mode the micro‐ filter/activated charcoal filter filters dust, pollen, and gaseous pollutants out of the air. This filter should be replaced during scheduled maintenance, refer to page 193, of your vehicle.
Ventilation Front ventilation
▷ Lever for changing the air flow direction, ar‐
row 1.
▷ Thumbwheels for opening and closing the
vents continuously, arrows 2.
▷ Thumbwheel to vary the temperature, ar‐
row 3. Toward blue: colder. Toward red: warmer.
Adjusting the ventilation ▷ Ventilation for cooling:
Adjust the vent to direct the air in your di‐ rection, such as if the vehicle interior is hot from the sun.
▷ Draft-free ventilation:
Adjust the vent to let the air flow past you.
Climate control
Controls
Ventilation in the rear
▷ Thumbwheel for continuous opening and
closing of the vents, arrow 1.
▷ Thumbwheel to vary the temperature, ar‐
row 2. Toward blue: colder. Toward red: warmer.
▷ Lever for changing the air flow direction, ar‐
row 3.
Parked-car ventilation The concept The parked-car ventilation ventilates the vehicle interior and lowers its temperature, if necessary. The system can be switched on and off at any external temperature, either directly or by using two preset switch-on times. It remains switched on for 30 minutes. Open the vents to allow air to flow out. Operation can be performed via iDrive. Switching on/off directly 1. "Settings" 2. "Climate" 3. "Activate parked-car vent."
The symbol on the automatic climate control
flashes if the system is switched on.
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
143
Controls
Climate control
Preselecting the switch-on time 1. "Settings" 2. "Climate" 3. "Timer 1:" or "Timer 2:" 4. Set the desired time. Activating the switch-on time 1. "Settings" 2. "Climate" 3. "Activate Timer 1" or "Activate Timer 2"
The symbol on the automatic climate control lights up when the switch-on time is activated. The symbol on the automatic climate control flashes when the system has been switched on. The system will only be switched on within the next 24 hours. After that, it needs to reactivated.
144
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
Interior equipment Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equipment is also described that is not available in a vehicle, e. g., because of the selected optional equip‐ ment or country variant. This also applies for safety-related functions and systems.
Integrated universal remote control The concept The integrated universal remote control can op‐ erate up to 3 functions of remote-controlled sys‐ tems such as garage door drives or lighting sys‐ tems. The integrated universal remote control replaces up to 3 different hand-held transmit‐ ters. To operate the remote control, the buttons on the interior rearview mirror must be program‐ med with the desired functions. The hand-held transmitter for the particular system is required in order to program the remote control.
During programming During programming and before activat‐ ing a device using the integrated universal re‐ mote control, ensure that there are no people, animals, or objects in the range of movement of the remote-controlled device; otherwise, there is a risk of injury or damage. Also follow the safety instructions of the hand- held transmitter.◀ Before selling the vehicle, delete the stored functions for the sake of security. Compatibility
If this symbol is printed on the packaging or in the instructions of the system to be controlled, the system is generally com‐
Interior equipment
Controls
patible with the integrated universal remote control. If you have any questions, please contact: ▷ Your service center. ▷ www.homelink.com on the Internet. HomeLink is a registered trademark of Johnson Controls, Inc. Controls on the interior rearview mirror
▷ LED, arrow 1. ▷ Buttons, arrow 2. ▷ The hand-held transmitter, arrow 3, is re‐
quired for programming.
Programming General information 1. Switch on the ignition. 2.
Initial setup: Press and hold the left and right button on the interior rearview mirror simultaneously for approximately 20 seconds until the LED on the interior rearview mirror flashes. This erases all programming of the buttons on the interior rearview mirror.
3. Hold the hand-held transmitter for the sys‐ tem to be controlled approx. 1 to 3 in/2.5 to 8 cm away from the buttons on the interior
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
145
Controls
Interior equipment
rearview mirror. The required distance de‐ pends on the manual transmitter.
4. Simultaneously press and hold the button of the desired function on the hand-held trans‐ mitter and the button to be programmed on the interior rearview mirror. The LED on the interior rearview mirror will begin flashing slowly.
5. Release both buttons as soon as the LED
flashes more rapidly. When the LED is flash‐ ing faster, this indicates that the button on the interior rearview mirror has been pro‐ grammed. If the LED does not flash faster after at least 60 seconds, change the distance between the interior rearview mirror and the hand- held transmitter and repeat the step. Several more attempts at different distances may be necessary. Wait at least 15 seconds be‐ tween attempts. Canada: if programming with the hand-held transmitter was interrupted, hold down the interior rearview mirror button and repeat‐ edly press and release the hand-held trans‐ mitter button for 2 seconds.
6. To program other functions on other but‐
tons, repeat steps 3 to 5.
The systems can be controlled using the interior rearview mirror buttons. Special feature of the alternating-code wireless system If you are unable to operate the system after re‐ peated programming, please check if the sys‐ tem to be controlled features an alternating- code system. Read the system's operating manual, or press the programmed button on the interior rearview mirror longer. If the LED on the interior rearview mirror starts flashing rapidly and then stays lit constantly for 2 seconds, the system features an alternating-code system. Flashing and con‐ tinuous illumination of the LED will repeat for approximately 20 seconds.
For systems with an alternating-code system, the integrated universal remote control and the system also have to be synchronized. Please read the operating manual of the system being set up for information on how to syn‐ chronize the system. Synchronizing is easier with the aid of a second person. To synchronize: 1. Park the vehicle within range of the remote-
controlled system.
2. Program the relevant button on the interior
rearview mirror as described.
3. Locate and press the synchronizing button on the system being programmed. You have approx. 30 seconds for the next step.
4. Hold down the programmed button on the interior rearview mirror for approximately 3 seconds and then release it. If necessary, repeat this work step up to three times in or‐ der to finish synchronization. Once synchro‐ nization is complete, the programmed func‐ tion will be carried out.
Reprogramming individual buttons 1. Switch on the ignition. 2. Press and hold the interior rearview mirror
button to be programmed.
3. As soon as the interior rearview mirror LED
starts flashing slowly, hold the hand-held transmitter for the system to be controlled approx. 1 to 3 in/2.5 to 8 cm away from the buttons on the interior rearview mirror. The required distance depends on the manual transmitter.
4. Likewise, press and hold the button of the desired function on the hand-held transmit‐ ter.
5. Release both buttons as soon as the interior
rearview mirror LED flashes more rapidly. When the LED is flashing faster, this indi‐ cates that the button on the interior rearview mirror has been programmed. The system
146
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
can then be controlled by the button on the interior rearview mirror. If the LED does not flash faster after at least 60 seconds, change the distance and repeat the step. Several more attempts at different distances may be necessary. Wait at least 15 seconds between attempts. Canada: if programming with the hand-held transmitter was interrupted, hold down the interior rearview mirror button and repeat‐ edly press and release the hand-held trans‐ mitter button for 2 seconds.
Controls
Before operation Before operating a system using the
integrated universal remote control, ensure that there are no people, animals, or objects within the range of movement of the remote-controlled system; otherwise, there is a risk of injury or damage. Also follow the safety instructions of the hand- held transmitter.◀ The system, such as the garage door, can be operated using the button on the interior rear‐ view mirror while the engine is running or when the ignition is started. To do this, hold down the button within receiving range of the system until the function is activated. The interior rearview mirror LED stays lit while the wireless signal is being transmitted. Deleting stored functions Press and hold the left and right button on the interior rearview mirror simultaneously for ap‐ proximately 20 seconds until the LED flashes rapidly. All stored functions are deleted. The functions cannot be deleted individually.
Interior equipment
Controls
Digital compass At a glance
1 Control button 2 Mirror display
Mirror display The point of the compass is displayed in the mirror when driving straight. Operating concept Various functions can be called up by pressing the control button with a pointed object, such as the tip of a ballpoint pen or similar object. The following setting options are displayed in suc‐ cession, depending on how long the control but‐ ton is pressed: ▷ Pressed briefly: turns display on/off. ▷ 3 to 6 seconds: compass zone setting. ▷ 6 to 9 seconds: compass calibration. ▷ 9 to 12 seconds: left/right-hand steering
setting.
▷ 12 to 15 seconds: language setting. Setting the compass zones Sets the particular compass zones on the vehi‐ cle so that the compass operates correctly; refer to World map with compass zones.
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
147
Controls
Interior equipment
World map with magnetic zones
Procedure 1. Press and hold the control button for approx. 3 to 4 seconds. The number of the set com‐ pass zone appears in the mirror.
2. To change the zone setting, press the con‐ trol button quickly and repeatedly until the number of the compass zone corresponding to your location appears in the mirror.
The set zone is stored automatically. The com‐ pass is ready for use again after approximately 10 seconds. Calibrating the digital compass The digital compass must be calibrated in the event of the following: ▷ The wrong point of the compass is dis‐
played.
▷ The point of the compass displayed does not change despite changing the direction of travel.
▷ Not all points of the compass are displayed.
Procedure 1. Make sure that there are no large metallic
objects or overhead power lines near the ve‐ hicle and that there is sufficient room to drive around in a circle.
2. Set the currently applicable compass zone. 3. Press and hold the control button for approx. 6 to 7 seconds so that "C" appears on the display. Next, drive in a complete circle at least once at a speed of no more than 4 mph/7 km/h. If calibration is successful, the "C" is replaced by the points of the com‐ pass.
Left/right-hand steering The digital compass is already set for right or left-hand steering at the factory. Setting the language Press and hold the control button for approx. 12
to 13 seconds. Briefly press the control button again to switch between English "E" and Ger‐ man "O".148
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
The setting is stored automatically after approx‐ imately 10 seconds.
Ashtray/cigarette lighter Ashtray Opening
Raise cover.
Emptying Take out the insert. Lighter
Danger of burns Only hold the hot lighter by its knob; oth‐ erwise, there is the danger of getting burned. Switch off the ignition and take the remote con‐ trol with you when leaving the vehicle so that children cannot use the lighter and burn them‐ selves.◀
Interior equipment
Controls
Push in the lighter. The lighter can be removed as soon as it pops back out.
Connecting electrical devices Note
Do not plug the charger into the socket Do not connect battery chargers to the
factory-installed sockets in the vehicle. Doing so may result in damage to the vehicle.◀
Sockets The lighter socket can be used as a socket for electrical equipment while the engine is running or when the ignition is switched on. The total load of all sockets must not exceed 140 watts at 12 volts. Do not damage the socket by using unsuitable connectors. Front center console
Raise the cap and remove the cover or cigarette lighter.
The lighter is located next to the ashtray.
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
149
Controls
Interior equipment
In the front passenger footwell
Socket is located below the glove compartment.
Rear center console
Remove cover.
In the cargo area
The socket is located on the left side in the cargo area.
USB interface for data transfer At a glance The USB interface for data transmission is lo‐ cated in the glove compartment. Depending on the variant, the USB interface may also be lo‐ cated in the center armrest.
The USB interface is located in the glove com‐ partment
The USB interface is located in the center arm‐ rest.
General information Connection for importing and exporting data on USB devices, e.g.: ▷ Personal Profile settings, refer to page 33. ▷ Music collection, see user's manual for Nav‐ igation, Entertainment and Communication. ▷ Importing trips, see user's manual for Navi‐ gation, Entertainment and Communication.
Notes Observe the following when connecting:
150
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
▷ Do not use force when plugging the con‐
nector into the USB interface.
▷ Do not connect devices such as fans or
lamps to the USB interface.
▷ Do not connect USB hard drives. ▷ Do not use the USB interface to recharge
external devices.
Through-loading system The concept The cargo area can be enlarged by folding down the rear seat backrest. The rear seat backrest is divided at a ratio of 40– 20–40. The sides can be folded down separately or to‐ gether. Notes
Danger of pinching Before folding down the rear seat backr‐ ests, ensure that the area of movement of the backrests is clear. In particular, ensure that no one is located in or reaches into the area of movement of the rear seat backrests when the middle section is folded down. Otherwise, injury or damage may result.◀
Locking the backrest Before driving with passengers in the rear of the vehicle, make sure that the backrests are engaged and thus locked in place. Otherwise, the restraining effect of the safety belts may be limited in an accident.◀
Retract the head restraint if necessary be‐ fore backrest is folded down
With folding head restraints, fold in the head re‐ straints before folding down the backrests, or damage may result.◀
Interior equipment
Controls
Opening 1. Unlock the belt lock of the center safety belt
in the rear using the latch plate of another safety belt. Insert the latch plate at the end of the belt into the specially designated fixture on the rear window shelf.
2.
3. Push the corresponding head restraint
down as far as it will go.
4. Pull the corresponding lever in the cargo
area to release the rear seat backrest.
5. The unlocked rear seat backrest moves for‐
ward slightly.
6. Fold backrest forward.
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
151
Controls
Interior equipment
Closing 1. Return the rear seat backrest to the upright
seating position and engage it.
Ensure that the lock is securely en‐ gaged
Make sure that the lock engages properly when folding back, otherwise transported cargo could enter the passenger compart‐ ment during braking or evasive maneuvers and endanger the vehicle occupants.◀
2. Release the belt tongue from the fixture on
the rear window shelf. Insert the belt tongue in the belt lock of the center safety belt. Make sure you hear the latch plate engage.
3.
To secure cargo, refer to page 164, with nets or draw straps, the cargo area is fitted with lashing eyes. Folding down the middle section 1. Fold in the middle head restraint. 2. Reach into the recess and pull the middle
section forward.
152
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
Storage compartments Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equipment is also described that is not available in a vehicle, e. g., because of the selected optional equip‐ ment or country variant. This also applies for safety-related functions and systems.
Storage compartments
Controls
▷ Compartments in the doors, refer to
page 154.
▷ Nets on the backrests of the front seats. ▷ Storage compartment in the rear center
console, refer to page 155.
Glove compartment Driver's side Opening
Notes
No loose objects in the passenger com‐ partment
Do not stow any objects in the passenger com‐ partment without securing them; otherwise, they may present a danger to occupants for in‐ stance during braking and avoidance maneu‐ vers.◀
Do not place anti-slip mats on the dash‐ board
Do not place anti-slip mats on the dashboard. The mat materials could damage the dash‐ board.◀
Storage compartments The following storage compartments are avail‐ able in the vehicle interior: ▷ Glove compartment on the driver's side, re‐
fer to page 153.
▷ Glove compartment on the front passenger
side, refer to page 154.
▷ Without Smoker's package: Front storage compartment, in front of the cupholders, re‐ fer to page 154.
▷ Storage compartment in the front center
armrest, refer to page 154.
Pull the handle.
Close the glove compartment again im‐ mediately
Close the glove compartment immediately after use while driving; otherwise, injury may occur during accidents.◀
Closing Fold up the cover.
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
153
Controls
Storage compartments
Front passenger side Opening
Front storage compartment
Raise the lid to open it.
Compartments in the doors
Do not stow any breakable objects Do not store any breakable objects, e. g. glass bottles, in the compartments, or there is an increased risk of injury in the event of an ac‐ cident.◀
Center armrest Front A storage compartment is located in the center armrest between the front seats. Opening
Pull the handle. The light in the glove compartment switches on. The net in the glove compartment is provided for stowing the storage tray for the cupholder, refer to page 155.
Close the glove compartment again im‐ mediately
Close the glove compartment immediately after use while driving; otherwise, injury may occur during accidents.◀
Closing Fold up the cover. Locking The glove compartment can be locked with an integrated key to separately secure the trunk lid, refer to page 38, for example. After the glove compartment is locked, the re‐ mote control can be handed over, such as at a hotel, without the integrated key, refer to page 30. This prevents access to the glove compartment and to the cargo area.
Fold the center armrest up.
Repositioning Center armrest can be pushed forwards or back‐ wards. It engages in the end positions.
154
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
Storage compartments
Controls
Connection for an external audio device
For a description, see the user's manual for Navigation, Entertain‐ ment and Communication.
Storage compartment in the rear Storage compartment is located in the rear cen‐ ter console.
Storage tray for front cupholders The cupholder with the storage tray can be used for additional storage. To do this, place the stor‐ age tray in the cupholder. Only use the storage tray for small objects, such as keys or the remote control. When not in use, stow the storage tray in the glove compartment net. Insert the storage tray into the net so that the top surface faces up. Note the trapezoidal shape of the net and tray. Rear In the center armrest.
Cupholders Notes
Shatter-proof containers and no hot drinks
Use light and shatter-proof containers and do not transport hot drinks. Otherwise, there is the increased danger of injury in an accident.◀
Unsuitable containers Do not forcefully push unsuitable contain‐ ers into the cupholders. This may result in dam‐ age.◀
Front
Pull the center armrest forward at the strap. To open: press the button. To close: push both covers back in, one after the other.
Pushing back the covers Push back the covers before folding up the center armrest; otherwise, the cupholder could become damaged.◀
Clothes hooks The clothes hooks are located in the grab han‐ dles in the rear.
Do not obstruct view When suspending clothing from the
hooks, ensure that it will not obstruct the driver's vision.◀
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
155
Controls
Storage compartments
No heavy objects Do not hang heavy objects from the hooks;
otherwise, they may present a danger to pas‐ sengers during braking and evasive maneu‐ vers.◀
Storage compartments in the cargo area Storage compartment A storage compartment is located on the left side. Net Small objects can be stowed in the net on the left side. Storage compartment Located on the right side is a storage compart‐ ment for the onboard vehicle tool kit, refer to page 196, and first aid kit, refer to page 208. Hooks/multi-function hook
Only transport heavy luggage in the trunk if it has been appropriately secured.◀
Retaining strap A retaining strap is available on the right side trim for fastening small objects. Lashing eyes in the cargo area To secure the cargo, refer to page 164, there are four lashing eyes in the cargo area. Floor net The floor net can also be used to Secure the load, refer to page 164, and to store small parts. Storage compartment under cargo floor panel
Maximum load To avoid damage to the vehicle, do not ex‐ ceed a maximum permitted load of 44 lbs/20 kg in the storage compartment under the cargo floor panel.◀
A multi-function hook is located on each side of the cargo area. The multi-function hooks can be loaded up to a max. of 8.8 lbs/4 kg.
Light and suitable objects only Only hang light bags or suitable objects
from the holders. Otherwise, there is a danger of objects flying about during braking and evasive maneuvers.
Raise the cargo floor panel, arrow 1, and latch at top, if necessary, arrow 2.
Partitioning the compartment The compartment can be divided using an at‐ tachable partition.
156
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
Storage compartments
Controls
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
157
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
Driving tips
This chapter provides you with information useful in dealing with specific driving and operating modes.
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
Driving tips
Things to remember when driving
Things to remember when driving Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equipment is also described that is not available in a vehicle, e. g., because of the selected optional equip‐ ment or country variant. This also applies for safety-related functions and systems.
Drive conservatively for the first 200 miles/300 km. Brake system Brakes require an initial break-in period of ap‐ prox. 300 miles/500 km to achieve optimized contact and wear patterns between brake pads and discs. Drive moderately during this break-in period. Clutch The function of the clutch reaches its optimal level only after a distance driven of approx. 300 miles/500 km. During this break-in period, engage the clutch gently. Following part replacement The same breaking in procedures should be ob‐ served if any of the components mentioned above have to be renewed in the course of the vehicle's operating life.
General driving notes Closing the trunk lid
Drive with the trunk lid closed Only drive with the tailgate closed; other‐ wise, in the event of an accident or braking or evasive maneuvers, passengers or other road users may be injured or the vehicle may be dam‐ aged. In addition, exhaust fumes may enter the passenger compartment.◀ If driving with the tailgate open cannot be avoided: ▷ Close all windows and the glass sunroof. ▷ Greatly increase the blower speed. ▷ Drive moderately.
Breaking-in period General information Moving parts need to be broken in to adjust to each other. The following instructions will help achieve a long vehicle life and good economy. Engine and differential Always obey the official speed limit. Up to 1,200 miles/2,000 km Do not exceed the maximum engine and road speed: ▷ For gasoline engine, 4,500 rpm and
100 mph/160 km/h.
Avoid full-throttle operation and use of the transmission's kickdown mode for the initial miles. From 1,200 miles/2,000 km The engine and vehicle speed can gradually be increased. Tires Due to technical factors associated with their manufacture, tires do not achieve their full trac‐ tion potential until after an initial breaking-in pe‐ riod.
160
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
Things to remember when driving
Driving tips
Hot exhaust system Hot exhaust system High temperatures are generated in the
exhaust system. Do not remove the heat shields installed and never apply undercoating to them. When driv‐ ing, standing at idle and while parking, take care to avoid possible contact between the hot ex‐ haust system and any highly flammable materi‐ als such as hay, leaves, grass, etc. Such contact could lead to a fire, and with it the risk of serious personal injury as well as property damage. Do not touch hot exhaust pipes; otherwise, there is the danger of getting burned.◀
Mobile communication devices in the vehicle
Mobile communication devices in the ve‐ hicle
It is advised that you do not use mobile commu‐ nication devices, e.g., mobile phones, inside the vehicle without connecting them directly to the external antenna. Otherwise, the vehicle elec‐ tronics and mobile communication devices can interfere with each other. In addition, there is no assurance that the radiation generated during transmission will be discharged from the vehicle interior.◀
Hydroplaning On wet or slushy roads, a wedge of water can form between the tires and road surface. This phenomenon is referred to as hydroplan‐ ing. It is characterized by a partial or complete loss of contact between the tires and the road surface, ultimately undermining your ability to steer and brake the vehicle.
Hydroplaning When driving on wet or slushy roads, re‐
duce your speed to prevent hydroplaning.◀
Driving through water Drive though calm water only if it is not deeper than 9.8 inches/25 cm and at this height, no faster than walking speed, up to 6 mph/10 km/h. Adhere to water depth and speed limita‐ tions
Do not exceed this water depth and walking speed; otherwise, the vehicle's engine, the elec‐ trical systems and the transmission may be damaged.◀
Braking safely Your vehicle is equipped with ABS as a standard feature. Applying the brakes fully is the most effective way of braking in situations when this is neces‐ sary. The vehicle maintains steering responsiveness. You can still avoid any obstacles with a minimum of steering effort. Pulsation of the brake pedal and sounds from the hydraulic circuits indicate that ABS is in its active mode. Objects in the area around the pedals No objects in the area around the pedals Keep floor mats, carpets, and any other objects out of the area of motion of the pedals; otherwise, the function of the pedals could be impeded while driving Do not place additional floor mats over existing mats or other objects. Only use floor mats that have been approved for the vehicle and can be properly fixed in place. Ensure that the floor mats are securely fastened again after they were removed for cleaning, for example.◀
Driving in wet conditions When roads are wet or there is heavy rain, briefly exert gentle pressure on the brake pedal every few miles.
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
161
Driving tips
Things to remember when driving
Should corrosion form on the brake discs, the brakes will tend to respond with a pulsating ef‐ fect that generally cannot be corrected. Condensation under the parked vehicle When using the automatic climate control, con‐ densation water develops that exits underneath the vehicle. Therefore, traces of condensed water under the vehicle are normal.
Ensure that this action does not endanger other road users. The heat generated in this process helps dry the brake discs and pads. In this way braking efficiency will be available when you need it. Hills Drive long or steep downhill gradients in the gear in which the least braking is required. Otherwise, the brake system may overheat, resulting in a reduction in the brake system efficiency. Manual transmission: You can increase the engine's braking effect by shifting down, going all the way to first gear, if necessary. Automatic transmission: You can increase the engine's braking effect by shifting down in the manual mode of the auto‐ matic transmission.
Avoid load on the brakes Avoid placing excessive load on the brake system. Light but consistent brake pressure can lead to high temperatures, brake wear and pos‐ sibly even brake failure.◀
Do not drive in neutral Do not drive in neutral or with the engine stopped, as doing so disables engine braking. In addition, steering and brake assist is unavailable with the engine stopped.◀
Brake disc corrosion Corrosion on the brake discs and contamination on the brake pads are furthered by: ▷ Low mileage. ▷ Extended periods when the vehicle is not
used at all.
▷ Infrequent use of the brakes. Corrosion occurs when the minimum pressure that must be exerted by the pads during brake applications to clean the discs is not reached.
162
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
Loading Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equipment is also described that is not available in a vehicle, e. g., because of the selected optional equip‐ ment or country variant. This also applies for safety-related functions and systems.
General information Overloading the vehicle To avoid exceeding the approved carrying capacity of the tires, never overload the vehicle. Overloading can lead to overheating and in‐ creases the rate at which damage develops in‐ side the tires. This could result in a sudden loss of tire inflation pressure.◀ No fluids in the trunk Make sure that fluids do not leak into the trunk; otherwise, the vehicle may be damaged.◀
Determining the load limit
Loading
Driving tips
hicle and unstable driving situations may result.
2. Determine the combined weight of the
driver and passengers that will be riding in your vehicle.
3. Subtract the combined weight of the driver and passengers from XXX kilograms or YYY pounds.
4. The resulting figure equals the available
amount of cargo and luggage load capacity. For example, if the YYY amount equals 1,000 lbs and there will be four 150 lbs pas‐ sengers in your vehicle, the amount of avail‐ able cargo and luggage load capacity is 400 lbs: 1,000 lbs minus 600 lbs = 400 lbs. 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.
Load
The maximum load is the sum of the weight of the occupants and the cargo. The greater the weight of the occupants, the less cargo that can be transported.
1. Locate the following statement on your ve‐
hicle’s placard: ▷ The combined weight of occupants and
cargo should never exceed XXX kg or YYY lbs. Otherwise, damage to the ve‐
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
163
Driving tips
Loading
Stowing cargo
Floor net The floor net can also be used to Secure the load and to store small parts.
▷ Heavy cargo: stow as far forward and as low as possible, ideally directly behind the cargo area separating wall.
▷ Very heavy cargo: when the rear seat is not occupied, secure each of the outer safety belts in the opposite buckle.
▷ Cover sharp edges and corners. ▷ If necessary, fold down the rear backrests to
stow cargo.
▷ Do not stack cargo above the top edge of the
backrests.
▷ Place protective material around any sharp- edged or pointed objects that could bump against the rear window while the vehicle is in motion.
Securing cargo Lashing eyes in the cargo area
To secure the cargo there are four lashing eyes in the cargo area.
Hook the floor net into the fittings in the cargo area floor.
Securing cargo ▷ Smaller and lighter items: secure with re‐ taining straps, the floor net or draw straps. ▷ Larger and heavy objects: secure with cargo
straps.
Attach the cargo straps, retaining straps or draw straps to the lashing eyes in the cargo area.
Securing cargo Always position and secure the cargo as described above; otherwise, it can endanger the car's occupants if sudden braking or swerving becomes necessary. Heavy or hard objects should not be carried loose inside the car; otherwise, they could be thrown around as a result of hard braking, sud‐ den swerves, etc., and endanger the occu‐ pants.◀
Roof-mounted luggage rack Note Roof racks are available as special accessories. Securing Follow the installation instructions of the roof rack.
164
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
Roof drip rail with flaps
Loading
Driving tips
The anchorage points are located in the roof drip rail above the doors. Fold the cover outward.
Loading Because roof racks raise the vehicle's center of gravity when loaded, they have a major effect on vehicle handling and steering response. Therefore, note the following when loading and driving: ▷ Do not exceed the approved roof/axle loads
and the approved gross vehicle weight.
▷ Distribute the roof load uniformly. ▷ The roof load should not be too large in area. ▷ Always place the heaviest pieces on the bot‐
tom.
▷ Secure the roof luggage firmly, e.g., tie with
ratchet straps.
▷ Do not let objects project into the opening
path of the trunk lid.
▷ Drive smoothly. Avoid sudden acceleration and braking maneuvers. Take corners gen‐ tly.
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
165
Driving tips
Saving fuel
Saving fuel Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equipment is also described that is not available in a vehicle, e. g., because of the selected optional equip‐ ment or country variant. This also applies for safety-related functions and systems.
General information Your vehicle contains advanced technology for the reduction of fuel consumption and emis‐ sions. Fuel consumption depends on a number of dif‐ ferent factors. The implementation of certain measures, driv‐ ing style and regular maintenance can have an influence on fuel consumption and on the envi‐ ronmental impact.
Remove unnecessary cargo Additional weight increases fuel consumption.
Remove attached parts following use Remove auxiliary mirrors, roof or rear luggage racks which are no longer required following use. Attached parts on the vehicle impair the aero‐ dynamics and increase the fuel consumption.
Close the windows and glass sunroof Driving with the glass sunroof and windows open results in increased air resistance and raises fuel consumption.
Check the tire inflation pressure regularly Check and, if necessary, correct the tire inflation pressure at least twice a month and before start‐ ing on a long trip. Low tire inflation pressure increases rolling re‐ sistance and thus raises fuel consumption and tire wear.
Drive away without delay Do not wait for the engine to warm up while the vehicle remains stationary. Start driving right away, but at moderate engine speeds. This is the fastest way for the cold engine to reach its operating temperature.
Look well ahead when driving Avoid unnecessary acceleration and braking. By maintaining a suitable distance to the vehicle driving ahead of you. Driving smoothly and looking ahead reduces fuel consumption.
Avoid high engine speeds Use 1st gear to get the vehicle in motion. Be‐ ginning with 2nd gear, accelerate rapidly. When accelerating, shift up before reaching high en‐ gine speeds.
166
Online Edition for Part no. 01 40 2 903 880 - 07 12 490
Saving fuel
Driving tips
Switch off any functions that are not currently needed Functions such as seat heating and the rear win‐ dow defroster require a lot of energy and con‐ sume additional fuel, especially in city and stop- and-go traffic. Therefore, switch off these functions if they are not actually needed.
Have maintenance carried out Have vehicles maintained regularly to achieve optimal vehicle economy and operating life. Have the maintenance carried out by your serv‐ ice center. Please also note the BMW Maintenance Sys‐ tem, refer to page 193.
ECO PRO The concept ECO PRO supports a driving style that saves on fuel consumption. For this purpose, the engine control and comfort functions, e. g. the climate control output, are adjusted. In addition, context-sensitive instructions can be displayed that assist in driving in a manner that optimizes fuel consumption. The extension of the range that is achieved as a result can be displayed in the instrument cluster. Activating ECO PRO
Press button repeatedly until ECO PRO is displayed in the instrument cluster.
When you reach the desired speed, shift into the highest applicable gear and drive with the en‐ gine speed as low as possible and at a constant speed. As a rule: driving at low engine speeds lowers fuel consumption and reduces wear. The gear shift indicator of your vehicle indicates the most fuel efficient gear.
