Login- Download PDF Manual
-
(P.334) (P.188)
(P.198)
RL models Canadian models only
2 : 3 :
＊ ＊ 60
2010 RL ０９／０４／０２ １８：４５：３５ ３１ＳＪＡ６５０ ００６６
KEYLESS ACCESS SYSTEM INDICATOR (P.68) CHARGING SYSTEM INDICATOR (P.62, 500) LIGHTS ON INDICATOR
FOG LIGHT INDICATOR MESSAGE INDICATOR (P.68) SECURITY SYSTEM INDICATOR
(P.69)
MULTI-INFORMATION DISPLAY
(P.71)
(P.64)
(P.65)
(P.65, 429)
VEHICLE STABILITY ASSIST (VSA) SYSTEM INDICATOR VSA ACTIVATION INDICATOR (P.429)
HIGH BEAM INDICATOR (P.65)
Instrument Panel
(P.65) / CRUISE MAIN INDICATOR ＊ ADAPTIVE CRUISE CONTROL (ACC) INDICATOR ＊
(P.66, 319)
ANTI-LOCK BRAKE SYSTEM (ABS) INDICATOR SIDE AIRBAG OFF INDICATOR (P.35, 63)
(P.64, 411)
ELECTRONICALLY CONTROLLED POWER STEERING SYSTEM (ECPS) INDICATOR PARKING BRAKE AND BRAKE SYSTEM (P.63, 502) INDICATOR
(P.68)
SEAT BELT REMINDER INDICATOR
(P.21, 62)
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) INDICATOR
(P.34, 63)
IMMOBILIZER SYSTEM INDICATOR
(P.64)
(P.62, 501)
MALFUNCTION INDICATOR LAMP LOW OIL PRESSURE INDICATOR
(P.62, 500)
SH-AWD INDICATOR (P.66)
COLLISION MITIGATION BRAKE SYSTEM (CMBS) INDICATOR (P.69)
＊
LOW FUEL INDICATOR
(P.66)
ADAPTIVE FRONT LIGHTING SYSTEM (AFS) INDICATOR ＊
(P.69, 144)
LOW TIRE PRESSURE/TPMS INDICATOR
(P.67, 423)
The U.S. instrument panel is shown. Differences for the Canadian models are noted in the text. ＊
If equipped.
61
2010 RL ０９／０４／０２ １８：４５：４５ ３１ＳＪＡ６５０ ００６７
If your front passenger does not fasten their seat belt, the indicator comes on about 6 seconds after the ignition switch is turned to the ON (II) position.
If either of you do not fasten your seat belt while driving, the beeper will sound and the indicator will flash again at regular intervals. For more information, see page
21
You will also see a ‘‘FASTEN SEAT BELT’’ or ‘‘FASTEN PASSENGER SEAT BELT’’ message on the multi- information display (see page
79
).
Instrument Panel Indicators
The instrument panel has many indicators to give you important information about your vehicle.
Seat Belt Reminder Indicator
This indicator comes on when you turn the ignition switch to the ON (II) position. It reminds you and your passenger to fasten your seat belts. A beeper also sounds if you have not fastened your seat belt.
If you turn the ignition switch to the ON (II) position before fastening your belt, the beeper sounds and the indicator flashes. If you do not fasten your seat belt before the beeper stops, the indicator stops flashing but remains on.
62
Low Oil Pressure Indicator
The engine can be severely damaged if this indicator flashes or stays on when the engine is running, or if a ‘‘CHECK ENGINE OIL LEVEL’’ message is on the multi-information display. For more information, see page
500
Charging System Indicator
If this indicator comes on when the engine is running, the battery is not being charged, and you will also see a ‘‘CHECK CHARGING SYSTEM’’ message on the multi-information display. For more information, see page
500
Malfunction Indicator Lamp
You will also see a ‘‘CHECK EMISSION SYSTEM’’ message on the multi-information display. For more information, see page
501
2010 RL ０９／０４／０２ １８：４５：５６ ３１ＳＪＡ６５０ ００６８
Instrument Panel Indicators
U.S.
Canada
Parking Brake and Brake System Indicator This indicator has two functions:
system. You will also see a ‘‘BRAKE FLUID LOW’’ or ‘‘CHECK BRAKE SYSTEM’’ message on the multi-information display. For more information, see page
508
1.
It comes on when you turn the ignition switch to the ON (II) position. It is a reminder to check the parking brake. Driving with the parking brake not fully released can damage the rear brakes, axles, and tires. If you drive without releasing the parking brake, a beeper will sound, and you will also see a ‘‘RELEASE PARKING BRAKE’’ message on the multi-information display (see page
78
).
2.
If it stays on after you have fully released the parking brake while the engine is running, or if it comes on while driving, it can indicate a problem in the brake
U.S.
Canada
Side Airbag Off Indicator This indicator comes on when you turn the ignition switch to the ON (II) position. If it comes on at any other time, it indicates that the passenger’s side airbag has automatically shut off. You will also see a ‘‘PASSENGER SIDE AIRBAG OFF’’ message on the multi- information display (see page 79
For more information, see page). 35
Supplemental Restraint System Indicator
This indicator comes on briefly when you turn the ignition switch to the ON (II) position. If it comes on at any other time, it indicates a potential problem with your front airbags. This indicator will also alert you to a potential problem with your side airbags, passenger’s side airbag automatic cutoff system, side curtain airbags, automatic seat belt tensioners driver’s seat position sensor, the front passenger’s weight sensors, or, on models with ACC, seat belt e-pretensioners. You will also see a ‘‘CHECK AIRBAG SYSTEM’’ message on the multi- information display (see page 79
For more information, see page). 34
63
2010 RL ０９／０４／０２ １８：４６：０５ ３１ＳＪＡ６５０ ００６９
Instrument Panel Indicators
Lights On Indicator
or
This indicator reminds you that the exterior lights are on. It comes on when the light switch is in either the position. This indicator
will also come on when the light switch is in AUTO and the lights turn on automatically. If you turn the ignition switch to the ACCESSORY (I) or the LOCK (0) position without turning off the light switch, this indicator will remain on. A reminder chime will also sound when you open the driver’s door.
Immobilizer System Indicator
This indicator comes on for a few seconds when you turn the ignition switch to the ON (II) position. It will then go off if you have a properly- coded remote. If it is not a properly- coded remote, the indicator will blink and the engine will not start (see page
151
).
64
If you use the remote, this indicator blinks several times when you turn the ignition switch from ACCESSORY (I) to the LOCK (0) position.
If you use the built-in key, this indicator blinks several times when you turn the ignition switch from ON (II) to the ACCESSORY (I) position.
Anti-lock Brake System (ABS) Indicator
This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position, and when the ignition switch is turned to the START (III) position. If this indicator comes on at any other time, there is a problem in the ABS. If this happens, take the vehicle to your dealer to have it checked. With this indicator on, your vehicle still has normal braking ability but no anti-lock function. You will also see a ‘‘CHECK ABS
SYSTEM’’ message on the multi- information display (see page 78
For more information, see page). 411
Turn Signal and Hazard Warning Indicators
The left or right turn signal indicator blinks when you signal a lane change or turn. If the indicator does not blink or blinks rapidly, it usually means one of the turn signal bulbs is burned out (see page ). Replace the bulb as soon as possible, since other drivers cannot see that you are signaling.
464
When you press the hazard warning button, both turn signals blink. All turn signals on the outside of the vehicle should flash.
2010 RL ０９／０４／０２ １８：４６：１９ ３１ＳＪＡ６５０ ００７０
Vehicle Stability Assist (VSA) System Indicator
This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.
If it comes on and stays on at any other time, or it does not come on when you turn the ignition switch to the ON (II) position, there is a problem with the VSA system. You will also see a ‘‘CHECK VSA SYSTEM’’ message on the multi- information display (see page 78
Take your vehicle to a dealer to have it checked. Without VSA, your vehicle still has normal driving ability, but will not have VSA traction and stability enhancement. For more information, see page429
).
Instrument Panel Indicators
VSA Activation Indicator
Fog Light Indicator
This indicator has three functions:
1.
2.
3.
It comes on as a reminder that you have turned off the vehicle stability assist (VSA) system.
It flashes when VSA is active (see page
429
).
It comes on along with the VSA system indicator if there is a problem with the VSA system. You will also see a ‘‘CHECK VSA SYSTEM’’ message on the multi- information display (see page 78
).
This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. For more information, see page
429
This indicator comes on when you turn on the fog lights. For more information, see page
142
High Beam Indicator
This indicator comes on with the high beam headlights. For more information, see page
140
This indicator also comes on with reduced brightness when the daytime running lights (DRL) are on (see page
142
).
Cruise Main Indicator
Onmodelswithoutadaptivecruise control(ACC) This indicator comes on when you turn on the cruise control system by pressing the CRUISE button on the steering wheel (see page
316
).
65
2010 RL ０９／０４／０２ １８：４６：３０ ３１ＳＪＡ６５０ ００７１
Instrument Panel Indicators
Adaptive Cruise Control (ACC) Indicator
Onmodelswithadaptivecruisecontrol (ACC) This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.
When you push the ACC button on the steering wheel, this indicator comes on green. You will also see ‘‘ACC’’ on the multi-information display.
If the indicator comes on orange, there is a problem with the ACC system. You will also see a ‘‘CHECK ACC SYSTEM’’ message on the multi-information display (see page 79
dealer to have it checked. For more information, see page). Take your vehicle to your
319
66
Low Fuel Indicator
LOW FUEL INDICATOR
This indicator is in the fuel gauge. It comes on as a reminder that you must refuel soon. You will also see a ‘‘FUEL LOW’’ message on the multi- information display (see page ). When the indicator comes on, there are about 2.69 U.S. gal (10.2 ) of fuel remaining in the tank before the needle reaches E. There is a small reserve of fuel remaining in the tank when the needle does reach E.
79
Super Handling-All Wheel Drive (SH-AWD) Indicator
78
This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. If this indicator comes on at any other time, there is a problem in the SH-AWD system. You will also see a ‘‘CHECK SH-AWD SYSTEM’’ message on the multi-information display (see page ) .Take your vehicle to a dealer to have it checked. For more information, see page 407
If the indicator blinks while driving, pull to the side of the road when it is safe, shift to Park, and let the engine idle until the indicator goes out. If it comes on while driving, it indicates the differential temperature is too high. You will also see a ‘‘SH-AWD DIFF TEMP. HIGH’’ message on the multi-information display (see page 78).
2010 RL ０９／０４／０２ １８：４６：３９ ３１ＳＪＡ６５０ ００７２
Instrument Panel Indicators
Pull to the side of the road when it is safe, shift to Park, and let the engine idle until the indicator goes out.
You will also see a ‘‘CHECK TIRE PRESSURE’’ message on the multi- information display (see page ).
79
2.
Check the tire pressure monitor on the multi-information display and determine the cause (see page
425
).
If this happens, pull to the side of the road when it is safe, check which tire has lost pressure on the multi- information display, and determine the cause. If it is because of a flat tire, have the flat tire repaired as soon as possible. If two or more tires are underinflated, call a professional towing service. For more information, see page 513
Continuing to drive with the SH-AWD indicator blinking may cause serious damage to the system.
Low Tire Pressure/ TPMS Indicator
This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.
This indicator has two functions:
1.
If it comes on while driving, it indicates that one or more of your vehicle’s tires are significantly low on pressure.
If this indicator begins to flash, there is a problem with the tire pressure monitoring system (TPMS). You will also see a ‘‘CHECK TPMS SYSTEM’’ message on the multi-information display. The indicator continues to flash for a while (approximately 1
minute), then stays on. If this happens, have your dealer check the system as soon as possible. For more information, see page 42367
2010 RL ０９／０４／０２ １８：４６：４７ ３１ＳＪＡ６５０ ００７３
Instrument Panel Indicators
The indicator comes on when you run the engine while the vehicle is not moving. To turn the indicator off, restart the engine.
Keyless Access System Indicator
This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. If it comes on at any other time, it indicates that there is a problem with the system. You will also see a ‘‘CHECK KEYLESS ACCESS SYSTEM’’ message on the multi-information display (see page 79
179). For more information, see page
Message Indicator
This indicator comes on when there is a system message on the multi- information display. Press the INFO button on the steering wheel (see ) to see the message (see page page ).
71
78Most of the time, this indicator comes on along with other indicators in the instrument panel such as the seat belt reminder indicator, SRS indicator, VSA system indicator, etc.
Electronically Controlled Power Steering System (ECPS) Indicator
78
This indicator normally comes on when you turn the ignition to the ON (II) position and goes off after the engine starts. If it comes on at any other time, there is a problem with the power steering system. You will also see a ‘‘CHECK POWER STEERING SYSTEM’’ message on the multi-information display (see page ). If this happens, stop the vehicle in a safe place, and turn off the engine. Reset the system by restarting the engine, and watch this indicator. If it does not go off or comes back on again while driving, take the vehicle to your dealer to have it checked. With the indicator on, the ECPS is turned off, which could make the vehicle harder to steer.
68
2010 RL ０９／０４／０２ １８：４６：５８ ３１ＳＪＡ６５０ ００７４
Security System Indicator
Adaptive Front Lighting System (AFS) Indicator
Ifequipped This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.
It comes on as a reminder that you have turned off the adaptive front lighting system (AFS).
78
). If this
This indicator blinks when there is a problem with the AFS system; you will also see a ‘‘CHECK ADAPTIVE FRONT LIGHTING SYSTEM’’ message on the multi-information display (see page happens, stop the vehicle in a safe place, turn the ignition switch to the ACCESSORY (I) or the LOCK (0) position, and restart the engine. If the indicator does not go off or blinks again, take your vehicle to a dealer to have it checked. For more information, see page
144
SECURITY SYSTEM INDICATOR
This indicator comes on when the security system is set. For more information, see page
315
Collision Mitigation Brake System (CMBS) Indicator
Ifequipped This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. It also comes on as a
Instrument Panel Indicators
reminder that you have turned off the collision mitigation brake system (CMBS).
The CMBS indicator also comes on if dirt or other debris blocks the radar sensor in the front grille. You will also see a ‘‘CHECK CMBS RADAR SENSOR’’ message on the multi-information display. When you clean the radar sensor, the indicator should go off the next time you turn the ignition switch to the ON (II) position.
If the indicator comes on at any other time, there is a problem with the CMBS. You will also see a ‘‘CHECK CMBS SYSTEM’’ message on the multi-information display. If this happens, take your vehicle to a dealer, and have it checked. For more information, see page 418
When this indicator is on, the CMBS is not working.69
2010 RL ０９／０４／０２ １８：４７：０７ ３１ＳＪＡ６５０ ００７５
Gauges
TACHOMETER
SPEEDOMETER
TEMPERATURE GAUGE
U.S. model is shown.
FUEL GAUGE
upper end of the white section of the gauge. If it reaches the red (hot) mark, pull safely to the side of the road. For more information, see page 497
Temperature Gauge This shows the temperature of the engine’s coolant. During normal operation, the pointer should rise from the bottom white mark to about the middle of the gauge. In severe driving conditions, such as very hot weather or a long period of uphill driving, the pointer may rise to the
70
Fuel Gauge This shows how much fuel you have. It may show slightly more or less than the actual amount. The needle returns to the bottom after you turn off the ignition.
Avoid driving with an extremely low f uel level. Running out of f uel could cause the engine to misf ire, damaging the catalytic converter.
2010 RL ０９／０４／０２ １８：４７：１３ ３１ＳＪＡ６５０ ００７６
Multi-Information Display
The multi-information display in the instrument panel displays various information and messages when the ignition switch is in the ON (II) position. Some of the messages help you operate your vehicle more comfortably. Others help to keep you aware of the periodic maintenance your vehicle needs for continued trouble-free driving.
When you open the driver’s door, a ‘‘Welcome’’ message is shown on the multi-information display. When you turn the ignition switch from the ON (II) position to the ACCESSORY (I) position, a ‘‘Goodbye’’ message is shown on the display.
INFO ( ▲ ▼ BUTTONS
U.S.
CANADA
SEL RESET BUTTON
You can change the display and customize your vehicle control settings by pressing the SEL/RESET or INFO buttons on the right side of the steering wheel.
With the ignition switch in the ON (II) position, the lower part of the multi-information display changes as shown in the illustration, each time you press the SEL/RESET button.
71
2010 RL ０９／０４／０２ １８：４７：２０ ３１ＳＪＡ６５０ ００７７
Multi-Information Display
Odometer
Trip Meter
When you reset Trip A, average fuel economy A is reset at the same time. When you reset Trip B, average fuel economy B is reset.
In the customizing mode, you can set Trip A, average fuel economy A, and average speed to reset at the same time when you refuel your vehicle (see page
99
).
ODOMETER
TRIP METER
The odometer shows the total distance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S. federal law and Canadian provincial/ territorial regulations to disconnect, reset, or alter the odometer with the intent to change the number of miles or kilometers indicated.
This meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it. There are two trip meters: Trip A and Trip B. Each trip meter works independently, so you can keep track of two different distances.
To reset a trip meter, display it, then press and hold the SEL/RESET button until the number resets to ‘‘0.0’’.
72
2010 RL ０９／０４／０２ １８：４７：２８ ３１ＳＪＡ６５０ ００７８
Outside Temperature
OUTSIDE TEMPERATURE
U.S.
CANADA
This shows the outside Fahrenheit temperature in U.S. models, and Celsius temperature in Canadian models.
The temperature sensor is in the front bumper. The temperature reading can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic. This can cause an incorrect temperature reading when your vehicle speed is under 19 mph (30 km/h). When you start your trip, the sensor is not fully acclimatized, therefore it may take several minutes until the proper temperature is displayed.
You can adjust the outside temperature display (see page
97
) .
In certain weather conditions, temperature readings near freezing (32°F, 0°C) could mean that ice is forming on the road surface.
Multi-Information Display
Engine Oil Life
ENGINE OIL LIFE
This shows the remaining life of the engine oil. It shows 100% after the engine oil is replaced and the display is reset. The engine oil life is calculated based on engine operating conditions and accumulated engine revolutions. For more information, see page
439
73
2010 RL ０９／０４／０２ １８：４７：３５ ３１ＳＪＡ６５０ ００７９
Multi-Information Display
Normal Display Messages With the ignition switch in the ON (II) position, the upper part of the display changes, as shown in the illustration, each time you press the button, ▼ the display returns to the previous message.
button. If you press the
▲
U.S.
CANADA
If ON
Press the Press the
▼ ▲
button button
74
2010 RL ０９／０４／０２ １８：４７：５１ ３１ＳＪＡ６５０ ００８０
Trip Computer Along with the trip meter, the trip computer calculates these values:
Instantaneous fuel mileage Range Elapsed Time Average Vehicle Speed Average Fuel Economy
INST. MPG (U.S. models)/INST. L/100km (Canadian models) This shows your instant fuel economy.
When you turn off the engine, INST. MPG or INST. L/100 km is also reset.
RANGE This shows the estimated distance you can travel on the fuel remaining in the fuel tank. This distance is estimated from the fuel economy you received over the last several miles(U.S.) or kilometers (Canada),
so it will vary with changes in speed, traffic, etc.
When the battery is disconnected, or you refuel, RANGE is also reset.
ELAPSED TIME This shows the accumulated traveling time since you last reset it. When you turn the ignition switch to the ON (II) position, ELAPSED TIME is reset. You can customize the ELAPSED TIME reset conditions on the multi- information display (see page ).
101
AVERAGE SPEED This shows the average speed you are traveling in miles per hour (mph) for U.S. models or kilometers per hour (km/h) for Canadian models.
When you reset Trip A, average speed is also reset.
Multi-Information Display
You can customize the average speed reset condition on the multi- information display (see page ).
99
AVERAGE FUEL A/B This shows your vehicle’s average fuel economy in mpg (U.S. models) or liter/100 km (Canadian models) since you last reset Trip A or Trip B.
The average fuel economy will be reset when you reset the trip meter, or if the vehicle’s battery goes dead or is disconnected.
You can customize the average fuel A reset condition on the multi- information display (see page
99
).
75
2010 RL ０９／０４／０２ １８：４７：５９ ３１ＳＪＡ６５０ ００８１
Multi-Information Display
SH-AWD Torque Distribution Monitor
Tire Pressure Monitor
Bluetooth
HandsFreeLink
U.S.
Canada
When the tire pressure monitor is shown on the multi-information display, press the SEL/RESET button. The display changes as shown. You can see the pressure of each tire in this monitor. If one or more tires are low, inflate them to the correct pressure. For more information, see page
423
You can receive or make phone calls from your cell phone through your HandsFreeLink vehicle’s (HFL) system without touching your cell phone.
Bluetooth
This monitor shows how much torque is being delivered to each wheel. For more information, see page
407
76
2010 RL ０９／０４／０２ １８：４８：０７ ３１ＳＪＡ６５０ ００８２
Maintenance Messages
To use the system, your cell phone and the HFL system must be linked. Not all cell phones are compatible with this system. Refer to page for instructions on how to link 354
your cell phone to HFL and how to receive or make phone calls, or visit the acura.com/handsfreelink website.When the engine oil life reaches 15%, the display shows ‘‘SERVICE DUE SOON’’ and the code for the maintenance items to be performed.
When the engine oil life reaches 5%, the display shows ‘‘SERVICE DUE NOW’’ along with the same maintenance items.
Multi-Information Display
Have your dealer do the indicated maintenance as soon as you see this message, and have them reset the display after completing the service.
If you do not perform the indicated maintenance or do not reset the display, the message changes to ‘‘SERVICE PAST DUE’’ when the engine oil life becomes 0%.
These messages appear on the multi- information display each time you turn the ignition switch to the ON (II) position.
For details on engine oil life and maintenance messages, refer to page 439
Also refer to page maintenance safety precautions.
for important
438
77
2010 RL ０９／０４／０２ １８：４８：２１ ３１ＳＪＡ６５０ ００８３
Multi-Information Display
Message Display When a problem is detected with your vehicle, a message will be shown on the multi-information display. If this happens, refer to the applicable pages of this owner’s manual, and follow the instructions.
When there are several messages to be shown, the system switches the messages every 5 seconds. The message is shown until you push the INFO ( ) button. To see the message again, press the INFO ( after the display disappears.
) button, 5 seconds
▲ ▼
▲ ▼
or
or
Here is a list of messages shown on the multi-information display:
78
See page 63, 502
See page
502
See page 62, 500
See page 62, 501
See page 62, 500
See page
398
See page
499
See page 64, 411
See page 65, 429
See page 69, 144
See page
68
See page 66, 407
2010 RL ０９／０４／０２ １８：４８：３７ ３１ＳＪＡ６５０ ００８４
Multi-Information Display
See page
399
See page
34, 63
See page
142
See page
35, 63
See page
458
U.S.
Canada
See page
319
See page
417
See page 69, 414
See page
13
See page
62
See page
62
See page
66
See page
381
See page
427
See page
425
See page 67, 425
See page
179
See page
177
See page
178
CONTINUED
79
2010 RL ０９／０４／０２ １８：４８：４３ ３１ＳＪＡ６５０ ００８５
Multi-Information Display
See page
441
See page
152
See page
152
80
2010 RL ０９／０４／０２ １８：４８：５４ ３１ＳＪＡ６５０ ００８６
▲ ▼
Customized Settings With the multi-information display and the INFO ( / ) and SEL/ RESET buttons on the right side of the steering wheel, you can customize some vehicle control settings for ‘‘DRIVER 1’’ or ‘‘DRIVER 2’’. If ‘‘DRIVER 1’’ or ‘‘DRIVER 2’’ is not displayed, customizing is not possible.
To have the driver’s ID detected, make sure your remote is linked to Memory Position the system (see Link ). Then use your remote to unlock the doors (see Keyless Access Setup on page 108
on page
104
).
To change the settings, the ignition switch must be in the ON (II) position, and the vehicle must be stopped with the transmission in Park.
To enter the customizing mode, press and hold the INFO ( / ) ▲ ▼ button for more than 3 seconds while the multi-information display is in its normal mode.
If you turn the ignition switch to the ACCESSORY (I) or the LOCK (0) position, or move the shift lever out of Park, the display will change to the normal screen.
You cannot customize the settings under these conditions:
173
When the keyless memory settings are off (see page If you disconnect the battery, and then do not unlock the door. When the multi-information display does not show the driver’s ID.
).
Multi-Information Display
The first customizing menu is: 87
85CHG SETTING (see page DEFAULT ALL (see page
Refer to the following table for a brief summary of each customizable setting and its default. For more information, refer to the page number references in the table.
CONTINUED
81
2010 RL ０９／０４／０２ １８：４９：０１ ３１ＳＪＡ６５０ ００８７
Multi-Information Display
CUSTOMIZE ENTRY CHG SETTING (see page 87)
CUSTOMIZE GROUP ACC SETUP (see page 89)
METER SETUP (see page 94)
CUSTOMIZE MENU
PRE-RUNNING CAR DETECT BEEP ACC DISPLAY SPEED UNIT LANGUAGE SELECTION
ADJUST OUTSIDE TEMP. DISPLAY
TRIP A RESET with REFUEL
ELAPSED TIME RESET
POSITION SETUP (see page 103)
MEMORY POSITION LINK
AUTO TILT & TELESCOPIC
Default setting Default setting for U.S. models Default setting for Canadian model
1 : ＊ 2 : ＊ 3 : ＊ 82
Description
CUSTOMIZE SET UP
Causes the system to beep when a vehicle ahead of you gets too close. Changes the ACC display speed unit. Changes the language used in the display.
Changes the outside temperature reading above or below its current reading. Causes trip meter A, the average fuel economy, and the average speed to reset when you refuel. Resets the elapsed time of your current trip.
Changes the driver’s seat, the steering wheel, and the outside mirror positions to your stored setting. Moves the steering wheel fully in and out when the key is removed.
previous setting
＊
0°F 0°C
＊
＊
〜 〜
5°F 3°C
＊
＊
＊
ON OFF mph km/h ENGLISH FRENCH SPANISH − 〜± − 〜±
5°F 3°C
ON OFF
＊
＊
IGN OFF TRIP A TRIP B ON OFF
＊
＊
ON OFF
Page 90
92
95
97
99
101
104
106
2010 RL ０９／０４／０２ １８：４９：０７ ３１ＳＪＡ６５０ ００８８
Multi-Information Display
CUSTOMIZE ENTRY CHG SETTING (see page 87)
CUSTOMIZE GROUP KEYLESS ACCESS SETUP (see page 108)
CUSTOMIZE MENU
DOOR UNLOCK MODE
KEYLESS ACCESS LIGHT FLASH
KEYLESS ACCESS BEEP
LIGHTING SETUP (see page 115)
INTERIOR LIGHT DIMMING TIME
HEADLIGHT AUTO OFF TIMER
AUTO LIGHT SENSITIVITY
AUTO DOOR LOCK
DOOR/WINDOW SETUP (see page 122)
＊
: Default setting
Description
Changes which doors unlock when you use the remote or grab the driver’s door handle. Causes some exterior lights to blink twice when you unlock the doors by grabbing the driver’s door handle. Cause the beeper to sound twice when you unlock the doors by grabbing the driver’s door handle. Changes how long (in seconds) the interior lights stay on after you close the doors. Changes how long (in seconds) the exterior lights stay on after you close the driver’s door. Changes the light level that causes the headlights to come on. The headlight switch needs to be in the AUTO position. Changes when the doors automatically lock.
＊
CUSTOMIZE SET UP DRIVER DOOR ONLY ALL DOORS ON OFF
＊
＊
ON OFF
＊
＊
0 SEC
60 SEC 30 SEC 15 SEC 60 SEC 30 SEC 15 SEC MAX HIGH MID LOW SHIFT FROM P WITH VEH SPD OFF
MIN
＊
＊
Page 109
111
113
116
118
120
123
CONTINUED 83
2010 RL ０９／０４／０２ １８：４９：１４ ３１ＳＪＡ６５０ ００８９
Multi-Information Display
CUSTOMIZE ENTRY CHG SETTING (see page 87)
CUSTOMIZE GROUP DOOR/WINDOW SETUP (see page 122)
CUSTOMIZE MENU AUTO DOOR UNLOCK
Description Changes when the doors automatically unlock.
DOOR LOCK MODE
KEYLESS LOCK ACKNOWLEDGMENT
SECURITY RELOCK TIMER
WIPER SETUP (see page 133)
WIPER ACTION
Changes which doors unlock with the first push of the remote’s unlock button. The exterior lights flash each time you press the LOCK or UNLOCK button. Changes how long it takes (in seconds) for the doors to relock and the security system to set after you unlock the driver’s door without opening it. Changes the wiper operation among two settings when the wiper switch is in the INT position. Changes all settings to the default.
DEFAULT ALL (see page 85)
＊
: Default setting
84
＊
CUSTOMIZE SET UP SHIFT TO P IGN OFF OFF DRIVER DOOR ALL DOORS
＊
＊
ON OFF
90 SEC 60 SEC 30 SEC
＊
INTERMITTENT WITH VEH SPD
＊
SET CANCEL
Page 125
127
129
131
134
85
2010 RL ０９／０４／０２ １８：４９：２１ ３１ＳＪＡ６５０ ００９０
If you want the settings as they were when the vehicle left the factory, select DEFAULT ALL, as described on this page.
If you want to change any vehicle control settings, select CHG SETTING, then press the SEL/ RESET button.
▲ ▼
Use the INFO ( / ) button on the steering wheel to select the settings and the SEL/RESET button to enter your selections.
Multi-Information Display
DEFAULT ALL
If you want to set the default settings, press the INFO ( / ) button to select DEFAULT ALL, then press the SEL/RESET button.
▲ ▼
If you want to cancel DEFAULT ALL, select CANCEL, then press the SEL/RESET button. The screen goes back to CUSTOMIZE ENTRY.
CONTINUED
85
2010 RL ０９／０４／０２ １８：４９：２６ ３１ＳＪＡ６５０ ００９１
Multi-Information Display
To set the default settings again, select DEFAULT ALL, and press the SEL/RESET button. Then select SET, and press the SEL/RESET button.
When DEFAULT ALL is set, you will see the above display for several seconds, then the screen returns to CUSTOMIZE ENTRY.
If DEFAULT ALL is not set, you will see the above display for several seconds, then the screen goes back to the normal message mode. Repeat the procedure to select DEFAULT ALL.
86
2010 RL ０９／０４／０２ １８：４９：３４ ３１ＳＪＡ６５０ ００９２
CHG SETTING You can customize some of the vehicle control settings to your preference. Here are the settings you can customize:
ADAPTIVE CRUISE CONTROL SETUP METER SETUP POSITION SETUP KEYLESS ACCESS SETUP LIGHTING SETUP DOOR/WINDOW SETUP WIPER SETUP
Multi-Information Display
While CHG SETTING in the CUSTOMIZE ENTRY is shown on the multi-information display, press the SEL/RESET button. The screen changes to ACC SETUP in the CUSTOMIZE GROUP.
Each time you press the INFO ( / ▲ ) button, the screen changes as ▼ shown on the next page. Press the INFO ( / ) button until you see the setup you want to customize, then press the SEL/RESET button to enter your selection.
▲ ▼
CONTINUED
87
2010 RL ０９／０４／０２ １８：４９：３９ ３１ＳＪＡ６５０ ００９３
Multi-Information Display
Press the Press the SEL/RESET button.
▲ ▼
button.
or
88
ADAPTIVE CRUISE CONTROL SETUP see page89
METER SETUP see page94
POSITION SETUP see page 103
KEYLESS ACCESS SETUP see page 108
LIGHTING SETUP see page 115
DOOR/WINDOW SETUP see page 122
WIPER SETUP see page 133
2010 RL ０９／０４／０２ １８：４９：４８ ３１ＳＪＡ６５０ ００９４
Multi-Information Display
Adaptive Cruise Control Setup Ifequipped Here are the two custom settings for adaptive cruise control (ACC):
PRE-RUNNING CAR DETECT BEEP ACC DISPLAY SPEED UNIT
While the multi-information display is in the CUSTOMIZE GROUP screen, select ACC SETUP by pressing the INFO ( / ) button, then press the SEL/RESET button.
▲ ▼
Each time you press the INFO ( /
