2008 Acura RDX Owners Manual

information display, press the SEL/ RESET button. The screen changes to CUSTOMIZE MENU. Press the INFO ( / ) button until you see the above display.

▲ ▼

Press the SEL/RESET button. The screen changes as shown above. Select the relock time you want (30, 60, or 90 seconds) by pressing the INFO ( / ) button, then press the SEL/RESET button to enter your selection.

▲ ▼

CONTINUED

107

2008 RDX ０７／０６／０１　１８：４４：５５　３１ＳＴＫ６１０　０１１３　

Multi-Information Display

When your choice is set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU.

If your choice is not set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU. If this happens, you need to repeat the same procedure.

To exit SECURITY RELOCK TIMER without changing the current setting, select EXIT by pressing the INFO ( / ) button, then press the SEL/RESET button. The screen goes back to CUSTOMIZE MENU.

▲ ▼

108

2008 RDX ０７／０６／０１　１８：４５：０３　３１ＳＴＫ６１０　０１１４　

Multi-Information Display

AutoDoorUnlock There are three settings you can choose from:

−

SHIFT TO P The driver’s door or all the doors unlock when you move the shift lever to Park.

−

IGN OFF The driver’s door or all the doors unlock when you turn the ignition switch to the LOCK (0) position.

−

OFF deactivated all the time.

The auto door unlock is

While DOOR SETUP is shown in the CUSTOMIZE GROUP of the multi- information display, press the SEL/ RESET button. The screen changes to CUSTOMIZE MENU. Press the INFO ( / ) button until you see the above display.

▲ ▼

Press the SEL/RESET button. The screen changes as shown above. Select the desired setting by pressing the INFO ( / ) button, then press the SEL/RESET button to enter your selection.

▲ ▼

CONTINUED

109

2008 RDX ０７／０６／０１　１８：４５：０９　３１ＳＴＫ６１０　０１１５　

Multi-Information Display

When your choice is set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU.

If your choice is not set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU. If this happens, you need to repeat the same procedure.

To exit AUTO DOOR UNLOCK without changing the current setting, select EXIT by pressing the INFO ( / ) button, then press the SEL/ ▲ ▼ RESET button. The screen goes back to CUSTOMIZE MENU.

110

2008 RDX ０７／０６／０１　１８：４５：１７　３１ＳＴＫ６１０　０１１６　

HEADLIGHTS/TURN SIGNAL/ FOG LIGHTS (P.114/115)

PADDLE SHIFTERS (P.297)

WINDSHIELD WIPERS/WASHERS/ REAR WINDOW WIPER/WASHER (P.112/113)

REMOTE AUDIO CONTROL BUTTONS (P.230)

VEHICLE STABILITY ASSIST (VSA) OFF SWITCH (P.313)

MIRROR CONTROLS (P.144)

VOICE CONTROL BUTTONS

＊ ＊

3,

BLUETOOTH HANDSFREELINK BUTTONS

(P.252)

STEERING WHEEL ADJUSTMENT

(P.119)

HORN ＊

CRUISE CONTROL (P.234) BUTTONS MULTI-INFORMATION BUTTONS

(P.72)

＊ ＊ ＊ ＊

1 : 2 : 3 : 4 :

To use the horn, press the center pad of the steering wheel. On RDX model only On RDX with Technology Package model only Refer to the navigation system manual.

Controls Near the Steering Wheel

HAZARD WARNING BUTTON (P.118)

UPPER DISPLAY (P.169)

＊

NAVIGATION SYSTEM / CENTER DISPLAY (P.168)

＊ ＊

＊

3,

PASSENGER AIRBAG (P.32) OFF INDICATOR

REAR WINDOW DEFOGGER/ HEATED MIRROR BUTTON (P.118/145) AUXILIARY INPUT JACK

(P.220)

ACCESSORY POWER SOCKET (P.155)

SEAT HEATER SWITCHES (P.139)

111

2008 RDX ０７／０６／０１　１８：４５：２６　３１ＳＴＫ６１０　０１１７　

Windshield Wipers and Washers

MIST The wipers run at high speed until you release the lever.

−

OFF

−

The wipers are not activated.

−

INT The length of the wiper interval is varied automatically according to the vehicle’s speed. Vary the delay by turning the INT TIME ring. If you turn it to the shortest delay, the wiper speed will increase to low speed operation when the vehicle speed exceeds 12
mph (20 km/h).

While the vehicle is stopped and in gear, the wipers sweep the windshield whenever you remove your foot from the brake pedal.

Windshield Wiper

1. 2. 3. 4. 5. 6.

MIST OFF INT LO Low speed HI High speed Windshield washers

Intermittent

− − −

Push the right lever up or down to select a position.

112

LO

−

The wipers run at low speed.

HI

−

The wipers run at high speed.

−

Windshield Washers

Pull the wiper control lever toward you, and hold it. The washers spray until you release the lever. The wipers run at low speed, then complete one more sweep after you release the lever.

2008 RDX ０７／０６／０１　１８：４５：３４　３１ＳＴＫ６１０　０１１８　

Windshield Wipers and Washers

−

OFF The wiper is not activated. When you turn the wiper switch to OFF while the rear window wiper is in action, it will return to its parked position.

When you shift the transmission to the reverse position with the front windshield wipers activated, the rear window wiper operates automatically. When the wiper control lever position is INT, the rear wiper operates intermittently. When it is LO or HI, the rear wiper operates continuously.

Rear Window Washer with Wiper Hold past ON to turn the rear − window wiper on and to spray the rear window washer. The rear window wiper makes one more sweep after you release the switch.

−

Rear Window Washer Only Rotate the switch counterclockwise from OFF to spray the window washer without activating the wiper. The washer will operate until you release the switch.

The rear window washer uses the same fluid reservoir as the wind- shield washer.

Rear Window Wiper and Washer

1. 2. 3. 4.

ON OFF Rear Window Washer with Wiper Rear Window Washer Only.

−

ON Rotate the switch clockwise to turn the rear window wiper ON. The wiper operates intermittently.

113

2008 RDX ０７／０６／０１　１８：４５：４０　３１ＳＴＫ６１０　０１１９　

Turn Signals and Headlights

−

Turn Signal Push down on the lever to signal a left turn and up to signal a right turn. To signal a lane change, push lightly on the lever, and hold it. The lever will return to center when you release it or complete a turn.

1. 2. 3. 4. 5. 6. 7. 8.

Turn signal Off Parking and interior lights Headlights High beams Flash high beams Fog lights off Fog lights on

114

−

Turning the switch to

’’ position turns on the

Headlights the ‘‘ parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights.

Turning the switch to the ‘‘ position turns on the headlights.

’’

’’ or ‘‘

When the light switch is in the ‘‘ ’’ position, the lights on indicator comes on as a reminder. This indicator stays on if you leave the light switch on and turn the ignition switch to the ACCESSORY (I) or the LOCK (0) position.

If you leave the lights on with the key removed from the ignition switch, you will hear a reminder beeper when you open the driver’s door.

2008 RDX ０７／０６／０１　１８：４５：４８　３１ＳＴＫ６１０　０１２０　

−

Push the lever

High Beams forward and the high beam indicator will come on (see page back to return to low beams.

). Pull it

67

Fog Lights Turn the fog lights on and off by turning the switch next to the headlight switch.

To flash the high beams, pull the lever back lightly, then release it. The high beams will stay on as long as you hold the lever back.

You can use the fog lights only when the headlights are on low beam. They will go off when the headlights are turned off.

Headlights

Automatic Lighting Off Feature This feature turns off the headlights, parking lights, taillights, side marker lights, license plate lights, and instrument panel lights within 15
seconds of removing the key from the ignition switch and closing the driver’s door.

This feature activates if you leave the headlight switch in the or

position, remove the key, then

open and close the driver’s door.

If you remove the key from the ignition switch with the headlight switch on, but do not open the door, the lights will turn off after 10
minutes.

CONTINUED

115

2008 RDX ０７／０６／０１　１８：４５：５４　３１ＳＴＫ６１０　０１２１　

Headlights

The lights will turn on again when you unlock or open the driver’s door. If you unlock the door, but do not open it within 15 seconds, the lights will go off. With the driver’s door open, you will hear a lights on reminder beeper.

You can change the ‘‘HEADLIGHT AUTO OFF TIMER’’ setting on the multi-information display (see page 98

).

position, the high beam

Daytime Running Lights With the headlight switch off or in the headlights and the high beam indicator come on with reduced brightness when you turn the ignition switch to the ON (II) position and release the parking brake. They remain on until you turn the ignition switch off, even if you set the parking brake.

The headlights revert to normal operation when you turn them on with the switch.

116

2008 RDX ０７／０６／０１　１８：４６：００　３１ＳＴＫ６１０　０１２２　

Instrument Panel Brightness

INSTRUMENT PANEL BRIGHTNESS CONTROL KNOB The knob on the instrument panel controls the brightness of the instru- ment panel lights. Turn the knob to adjust the brightness. Separate adjustments can be made when the headlights are on and off.

You will hear a beep when maximum or minimum brightness is reached. You will also hear a beep when the maximum level is canceled by turning the knob a click to the left.

U.S. model is shown

To reduce glare at night, the instrument panel illumination dims when you turn the light switch to the

or

position.

The level of brightness is shown on the multi-information display while you adjust it. It goes out 5 seconds after you finish adjusting.

117

2008 RDX ０７／０６／０１　１８：４６：０８　３１ＳＴＫ６１０　０１２３　

Rear Window Defogger, Hazard Warning Button

If you do not turn it off, the defogger will automatically shut itself off after a certain period depending on the ambient temperature. It also shuts off when you turn off the ignition switch. You have to turn it on again when you restart the vehicle.

In cold weather, the defogger will not automatically shut itself off. You must manually shut off the rear window defogger when it is no longer needed.

Make sure the rear window is clear and you have good visibility before starting to drive.

The defogger wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side-to-side.

Hazard Warning Button

Push the button between the center vents to turn on the hazard warning lights (four-way flashers). This causes all outside turn signals and both indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.

Rear Window Defogger

The rear window defogger clears fog, frost, and thin ice from the window. Push the defogger button to turn it on and off. Pushing this button also turns the mirror heaters on and off. The indicator in the button comes on to show the defogger is on.

118

2008 RDX ０７／０６／０１　１８：４６：１８　３１ＳＴＫ６１０　０１２４　

Steering Wheel Adjustment Make any steering wheel adjustment before you start driving.

Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.

Adjust the steering wheel only when the vehicle is stopped.

1.

Push the lever under the steering column all the way down.

2.

Move the steering wheel up or down, and in or out, so it points toward your chest, not toward your face. Make sure you can see the instrument panel gauges and indicators.

Steering Wheel Adjustment, Keys and Locks

Keys

KEY NUMBER TAG

MASTER KEYS WITH REMOTE TRANSMITTER

VALET KEY (Light Gray)

LEVER

3.

Push the lever up to lock the steering wheel in position.

4.

Make sure you have securely locked the steering wheel in place by trying to move it up, down, in, and out.

The master key fits all the locks on your vehicle. The valet key works only in the ignition and the door locks. You can keep the glove box and console compartment locked when you leave your vehicle and the valet key at a parking facility.

CONTINUED

119

2008 RDX ０７／０６／０１　１８：４６：２７　３１ＳＴＫ６１０　０１２５　

Keys and Locks

You should have received a key number tag with your keys. You will need this key number if you ever have to get a lost key replaced. Use only Acura-approved key blanks.

RetractableMasterKey

RELEASE BUTTON

Push

These keys contain electronic circuits that are activated by the immobilizer system. They will not work to start the engine if the circuits are damaged.

Protect the keys from direct sunlight, high temperature, and high humidity.

Do not drop the keys or set heavy objects on them.

Keep the keys away from liquids. If they get wet, dry them immediately with a soft cloth.

The valet key does not contain a battery. Do not try to take it apart.

120

The master key can be retracted into the remote transmitter. To use the key, push the release button to release the key from the transmitter. The key should be fully extended. To retract the key, push the release button and at the same time push the key into the remote transmitter until it is securely latched.

Always use the fully-extended key when you insert it to the ignition switch. If the key does not fully extend, the immobilizer system may not operate properly and prevents from starting the engine.

The key may come in contact with your finger while being retracted or extended. Make sure your fingers do not touch the pivot of the key when retracting or extending the key.

2008 RDX ０７／０６／０１　１８：４６：３６　３１ＳＴＫ６１０　０１２６　

The immobilizer system protects your vehicle from theft. If an improperly-coded key (or other device) is used, the engine’s fuel system is disabled.

When you turn the ignition switch to the ON (II) position, the immobilizer system indicator should come on briefly, then go off. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to the LOCK (0) position, remove the key, reinsert it, and turn the ignition switch to the ON (II) position again.

Immobilizer System

The system may not recognize your key’s coding if another immobilizer key or other metal object (i.e. key fob) is near the ignition switch when you insert the key.

If the system repeatedly does not recognize the coding of your key, contact your dealer.

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle undrivable.

Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

If you have lost your key and cannot start the engine, contact your dealer.

Always take the ignition key with you whenever you leave the vehicle alone.

ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

121

2008 RDX ０７／０６／０１　１８：４６：４３　３１ＳＴＫ６１０　０１２７　

Ignition Switch

If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key.

−

You can

ACCESSORY (I) operate the audio system and the accessory power sockets in this position.

You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or the ACCESSORY (I) position and open the driver’s door. Remove the key to turn off the beeper.

You will also see a ‘‘REMOVE KEY’’ message on the multi-information display (see page

78

).

−

This is the normal key

ON (II) position when driving. Several of the indicators on the instrument panel come on as a test when you turn the ignition switch from the ACCESSORY (I) to the ON (II) position.

The shift lever must be in Park before you can remove the key from the ignition switch.

−

Use this position

START (III) only to start the engine. The switch returns to the ON (II) position when you let go of the key.

The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), and START (III).

−

You can insert or

LOCK (0) remove the key only in this position. To turn the key, the shift lever must be in Park, and you must push the key in slightly.

122

2008 RDX ０７／０６／０１　１８：４６：５２　３１ＳＴＫ６１０　０１２８　

Power Door Locks

Driver’s Side

Lock

LOCK TAB

Unlock

Lock

Unlock

Passenger’s Side

MASTER DOOR LOCK SWITCH

Each front door has a master door lock switch. Either switch locks and unlocks all doors and the tailgate. Push the top of the switch to lock all doors and the tailgate; push the bottom to unlock them.

Door Locks

When the door is unlocked, you can see the red indicator on the lock tab next to the inside door handle.

All doors and the tailgate can be locked from the outside by using the key in the driver’s door lock. To unlock only the driver’s door, insert the key, turn the key, and release it. The remaining doors and the tailgate unlock when you turn the key a second time within a few seconds.

To unlock

To lock

You can change the ‘‘DOOR LOCK MODE’’ setting on the multi- information display (see page

103

).

Each door has a lock tab next to the inside door handle. When you pull backward on the lock tab on the driver’s door, all the doors and the tailgate lock. Pushing forward on the lock tab on the driver’s door unlocks only that door. The lock tab on the each passenger’s door locks and unlocks only that door.

CONTINUED

123

2008 RDX ０７／０６／０１　１８：４７：０１　３１ＳＴＫ６１０　０１２９　

Door Locks

When the vehicle speed reaches about 9 mph (about 15 km/h) or more, all the doors lock automatically.

You can change the ‘‘AUTO DOOR LOCK ’’ setting in the multi- information display (see page

101

).

When you shift to P after driving, the driver’s door unlocks.

You can change the ‘‘AUTO DOOR UNLOCK’’ setting in the multi- information display (see page

109

).

124

To lock any passenger’s door when getting out of the vehicle, pull backward on the lock tab and close the door. To lock the driver’s door, remove the key from the ignition switch and pull backward on the lock tab. Then close the door.

LockoutPrevention With the driver’s door open and the key in the ignition, both master door lock switches are disabled. They are not disabled if the driver’s door is closed. Pushing the switch down on the open front passenger’s door will lock all doors and the tailgate.

Childproof Door Locks

Lock

LEVER

The childproof door locks are designed to prevent children seated in the rear from accidentally opening the rear doors. Each rear door has a lock lever near the edge. With the lever in the LOCK position (lever is down), the door cannot be opened from the inside regardless of the position of the lock tab. To open the door, push the lock tab forward and use the outside door handle.

2008 RDX ０７／０６／０１　１８：４７：０７　３１ＳＴＫ６１０　０１３０　

The tailgate will lock when you lock the driver’s door, and will unlock when you unlock all doors.

SWITCH

You can change the ‘‘DOOR LOCK MODE’’ setting on the multi- information display (see page

103

).

Tailgate

TAILGATE HANDLE

To open the tailgate, press and hold the switch, then lift up.

To close the tailgate, hold the tailgate handle, lower the tailgate, then press down on the back edge.

Keep the tailgate closed at all times while driving to avoid damaging the tailgate and to prevent exhaust gas from getting into the interior. See Carbon Monoxide Hazard 56

on page

125

2008 RDX ０７／０６／０１　１８：４７：１３　３１ＳＴＫ６１０　０１３１　

Tailgate

Unlocking the Tailgate

If you need to unlock the tailgate manually, it means there is a problem with the tailgate. Have the vehicle checked by your dealer.

COVER

LEVER

If the power door lock system cannot unlock the tailgate, unlock it manually.

Push and hold the release lever to the right as shown, then push the tailgate to open it.

Use a small flat-tip screwdriver to remove the cover on the back of the tailgate.

126

2008 RDX ０７／０６／０１　１８：４７：２２　３１ＳＴＫ６１０　０１３２　

UNLOCK BUTTON

LOCK BUTTON

PANIC BUTTON

−

LOCK Press this button once to lock all doors and the tailgate. Some exterior lights will flash. When you push LOCK twice within 5 seconds, you will hear a beep to verify that the doors and tailgate are locked and the security system has set. This button does not work if any door or tailgate is not fully closed.

To change the ‘‘KEYLESS LOCK ACKNOWLEDGEMENT’’ setting, see page

105

−

Press this button once

UNLOCK to unlock the driver’s door. Push it twice to unlock the other doors. Some exterior lights will flash twice when you push the button. If you do not open any door or the tailgate within 30 seconds, they will automatically relock.

To change the ‘‘DOOR LOCK 103
MODE’’ setting, see page

Remote Transmitter

When you press the UNLOCK button, the ceiling lights (if the front and rear ceiling light switches are in the door activated position) will come on. If you do not open any door, the lights stay on for about 30
seconds, then fade out. If you relock the doors with the remote transmitter before 30 seconds have elapsed, the lights go off immediately.

To change the ‘‘SECURITY RELOCK TIMER’’ setting, see page 107

To change the ‘‘INTERIOR LIGHT DIMMING TIME’’ setting, see page 96

−

Press this button for

PANIC about 1 second to attract attention; the horn will sound, and the exterior lights will flash for about 30 seconds. To cancel panic mode, press any button on the remote transmitter, or turn the ignition switch to the ON (II) position.

127

2008 RDX ０７／０６／０１　１８：４７：３１　３１ＳＴＫ６１０　０１３３　

Remote Transmitter

Remote Transmitter Care

Avoid dropping or throwing the transmitter.

Protect the transmitter from extreme temperature.

Do not immerse the transmitter in any liquid.

If you lose a transmitter, the replacement needs to be reprogrammed by your dealer.

Replacing the Transmitter Battery If it takes several pushes on the button to lock or unlock the doors and the tailgate, replace the battery as soon as possible. Battery type: CR1616

128

KEYPAD

SCREW

To replace the battery:

1.

2.

Remove the screw at the base of the transmitter with a small Phillips-head screwdriver.

Separate the keypad from the transmitter by pushing any button from outside.

2008 RDX ０７／０６／０１　１８：４７：３９　３１ＳＴＫ６１０　０１３４　

4.

Remove the old battery and note the polarity. Make sure the polarity of the new battery is the same ( insert it in the keypad.

side facing up), then

−

BATTERY

3.

Place a cloth on the edge of the keypad, and remove the upper half by carefully prying on the edge with a small flat-tip screwdriver.

An improperly disposed of battery can hurt the environment. Always confirm local regulations for battery disposal.

5.

Snap the two halves of the keypad, then install the parts in reverse order.

Remote Transmitter

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

129

2008 RDX ０７／０６／０１　１８：４７：４６　３１ＳＴＫ６１０　０１３５　

Remote Transmitter

Keyless Memory Settings

TM

Here are the settings activated with the remote;

Driving position memory (see page

146

).

When you unlock and open the driver’s door with the remote transmitter, the driver’s seat (except the power lumbar feature) and outside mirrors start to move to the positions stored in memory. The indicator in the related memory button to the remote comes on.

When you unlock the driver’s door with your remote, each remote activates the keyless memory settings related to that remote. The driver’s ID (MEMORY 1 or MEMORY 2) is shown on the back of each remote.

130

To turn off this feature, press and hold the LOCK and UNLOCK buttons at the same time. The LED in the remote will blink twice. Then release the buttons. Doing this cancels the keyless memory settings for that remote.

To turn the keyless memory settings back on, repeat this procedure. The LED will blink once to indicate the feature has been turned on.

2008 RDX ０７／０６／０１　１８：４７：５７　３１ＳＴＫ６１０　０１３６　

−

12 13

Driver’s Seat Adjustments Seepages forimportantsafety informationandwarningsabouthowto properlypositiontheseatsandseat- backs.

The controls for the power adjustable driver’s seat are on the outside edge of the seat bottom. You can adjust the seat with the ignition switch in any position. Make all seat adjustments before you start driving.

Moves the seat forward and backward.

Moves the front of the seat up or down.

Seats

Raises or lowers the seat.

Moves the whole seat up and forward, or down and backward. The front of the seat also tilts up or down at the same time.

Adjusts the seat- back angle forward or backward.

Increases or decreases the lumbar support.

131

2008 RDX ０７／０６／０１　１８：４８：０４　３１ＳＴＫ６１０　０１３７　

Seats

Front Passenger’s Seat Adjustments Seepages forimportantsafety − informationandwarningsabouthowto properlypositiontheseatsandseat- backs.

12 13

Make all seat adjustments before you start driving.

BAR

LEVER

To adjust the seat forward or backward, pull up on the bar under the seat cushion’s front edge. Move the seat to the desired position, and release the bar. Try to move the seat to make sure it is locked in position.

To change the seat-back angle, pull up on the lever on the outside of the seat bottom.

Once your seat is adjusted correctly, rock it back and forth to make sure the seat is locked in position.

132

2008 RDX ０７／０６／０１　１８：４８：１２　３１ＳＴＫ６１０　０１３８　

Head Restraints Seepage forimportantsafety informationandawarningabout improperlypositioningheadrestraints.

14

Your vehicle is equipped with head restraints in all seating positions to help protect you and your passengers from whiplash and other injuries.

They are most effective when you adjust them so the center of the back of the occupant’s head rests against the center of the restraint.

Seats

Front

CUSHION

LEG

SEAT BACK

RELEASE BUTTON

AdjustingtheHeadRestraint The front and rear head restraints adjust for height. You need both hands to adjust the restraint. Do not attempt to adjust it while driving. To raise it, pull upward. To lower the restraint, push the release button and push the restraint down.

CONTINUED

133

2008 RDX ０７／０６／０１　１８：４８：１８　３１ＳＴＫ６１０　０１３９　

When reinstalling a head restraint, put the legs back in place. Then adjust it to the appropriate height while pressing the release button.

Make sure the removed head restraints are securely stored.

Failure to reinstall the head restraints can result in severe injury during a crash.

Always replace the head restraints before driving.

Seats

Rear

CUSHION

LEGS

SEAT BACK

RELEASE BUTTON

RemovingtheHeadRestraint To remove a head restraint for cleaning or repair, pull it up as far as it will go. Push the release button, then pull the restraint out of the seat- back.

134

2008 RDX ０７／０６／０１　１８：４８：２６　３１ＳＴＫ６１０　０１４０　

Seats

This reduces the distance between the restraint and the occupant’s head. It also helps protect the occupants against whiplash and injuries to the neck and upper spine.

After a collision, the activated restraint should return to its normal position.

If the restraints do not return to their normal position, or in the event of a severe collision, have the vehicle inspected by a Acura dealer.

For a head restraint system to work properly:

Do not hang any items on the head restraints, or from the restraint legs.

Do not place any object between an occupant and the seat-back.

Install each restraint in its proper location.

Only use genuine Acura replacement head restraints.

ActiveHeadRestraints

The driver’s and front passenger’s seats have active head restraints. If the vehicle is struck severely from the rear, the occupant properly secured with the seat belt will be pushed against the seat-back and the head restraint will automatically move forward.

135

2008 RDX ０７／０６／０１　１８：４８：３４　３１ＳＴＫ６１０　０１４１　

Seats

Armrests

Front

Rear

The lid of the console compartment can be used as an armrest.

The rear seat armrest is in the center of the rear seat. Pivot it down to use it.

136

Folding the Rear Seats Down The rear seat-backs can be folded down to give more cargo room. Each side folds down separately. So you can still carry a passenger in the rear seat.

Remove any items from the seat before folding down the seat-back.

Make sure there are no items on the floor before folding down the seats.

2008 RDX ０７／０６／０１　１８：４８：４３　３１ＳＴＫ６１０　０１４２　

Seats

BUCKLE

1.

Move the front seats as far forward as possible. Make sure the front seat-backs are in the upright positions.

2.

Store the center seat belt buckle into the pocket in the rear seat- back.

3.

Lower the head restraints to their lowest positions.

4.

Push the armrest back in place.

5.

Lift the front edge of the rear seat cushion, then pull up on the rear of the seat cushion, then fold the cushion forward.

6.

7.

RELEASE LEVER

Pull up the release lever on the outside of the seat-back. Fold the seat-back forward.

Move the front seats backward to the desired position. Make sure the front passenger’s seat is locked in place.

CONTINUED

137

2008 RDX ０７／０６／０１　１８：４８：５０　３１ＳＴＫ６１０　０１４３　

Seats

Do not put any heavy items on the seat-back when it is folded down.

Make sure all items in the cargo area are secured. Loose items can fly forward and cause injury if you have Carrying Cargo to brake hard (See on page

283

).

Make sure that the folded down rear seat does not interfere with the front passenger’s seat-back. This will cause the front passenger’s weight sensors and the front passenger’s seat belt reminder indicator to work improperly (see pages ). Also check the passenger airbag off indicator to assure proper operation of the passenger’s front airbag.

and

20

32

INDICATOR

RELEASE LEVER

After returning the seat-back to the upright position, tug on the seat-back to make sure it is latched. If the seat- back is not latched fully, the seat belt will not work properly and you will see the red indicator behind the release lever as shown.

To return the seat cushion to its original position, lift up the seat cushion, then place the rear of the seat cushion at the base of the seat- back. Use the seat buckles as guides. Lower the front of the seat cushion until it locks into place.

Make sure the seat-back and seat cushion are locked securely and all rear shoulder belts are positioned in front of the rear seat-backs.

138

2008 RDX ０７／０６／０１　１８：４８：５８　３１ＳＴＫ６１０　０１４４　

Passenger’s Seat

HEATERS

Driver’s Seat

SEAT HEATER SWITCHES

Both front seats are equipped with seat heaters. The passenger seat is only heated in the seat bottom because of the side airbag cutoff system.

The ignition switch must be in the ON (II) position to use seat heaters. Push the top of the switch, HI, to rapidly heat up the seat. After the seat reaches a comfortable temperature, select LO by pushing the bottom of the switch. This will keep the seat warm.

Seat Heaters

In the HI setting, the heater turns off when the seat gets warm, and turns back on after the seat’s temperature drops.

In the LO setting, the heater runs continuously. It does not cycle with temperature changes.

Follow these precautions whenever you use the seat heaters:

Use the HI setting only to heat the seats quickly, because it draws large amounts of current from the battery.

If the engine is left idling for an extended period, do not use the seat heaters, even on the LO setting. It can weaken the battery, causing hard starting.

139

2008 RDX ０７／０６／０１　１８：４９：０３　３１ＳＴＫ６１０　０１４５　

The windows will operate for up to 10 minutes after you turn off the ignition switch. Opening either front door cancels this function.

Closing a power window on someone’s hands or fingers can cause serious injury.

Make sure your passengers are away from the windows before closing them.

When you push the MAIN switch in, the switch is off, and the passenger windows cannot be raised or lowered. To cancel this feature, push on the switch again to get it to pop out. Keep the MAIN switch off when you have children in the vehicle so they do not injure themselves by operating the windows unintentionally.

Power Windows

DRIVER’S WINDOW SWITCH

MAIN SWITCH

Turn the ignition switch to the ON (II) position to raise or lower any window. To open the window, push the switch down and hold it. Release the switch when you want to stop the window. To close the window, pull back on the switch and hold it.

140

2008 RDX ０７／０６／０１　１８：４９：０８　３１ＳＴＫ６１０　０１４６　

Power Windows

−

To open or close either

AUTO front window fully, push or pull the window switch firmly down or up to the second detent, and release it. The window will automatically go up or down all the way. To stop the window, pull or push the window switch briefly.

To open or close either front window partially, push down or pull back on the window switch lightly to the first detent and hold it. The window will stop when you release the switch.

−

AUTO REVERSE If either front window senses any obstacle while it is closing automatically, it will reverse direction and then stop. To close the window, remove the obstacle, then use the window switch again.

Auto reverse stops sensing when the window is almost closed. You should always check that all passengers and objects are away from the window before closing it.

141

2008 RDX ０７／０６／０１　１８：４９：１４　３１ＳＴＫ６１０　０１４７　

Moonroof

Turn the ignition switch to the ON (II) position before operating the moonroof switch on the ceiling console.

To open the moonroof fully, pull back the moonroof switch firmly. The moonroof opens all the way. To stop the moonroof from opening fully, briefly move the switch in either direction.

To tilt the moonroof, push the center of the moonroof switch straight up. To stop the moonroof from tilting fully open, push the moonroof switch forward.

MOONROOF SWITCH

Open

Tilt

Close

To open or close the moonroof partially, pull or push the moonroof switch lightly to the first detent and hold it. The moonroof will stop when you release the switch.

To close the moonroof fully, push the moonroof switch forward to the second detent, then release it. The moonroof closes all the way. To stop the moonroof from closing all the way, briefly move the switch in either direction.

142

2008 RDX ０７／０６／０１　１８：４９：２０　３１ＳＴＫ６１０　０１４８　

Opening or closing the moonroof on someone’s hands or fingers can cause serious injury.

Make sure all hands and fingers are clear of the moonroof before opening or closing it.

Moonroof

The moonroof has a key-off delay. You can open and close the moonroof for up to 10 minutes after you turn off the ignition switch. The key-off delay cancels as soon as you open either front door. You must then turn the ignition switch to the ON (II) position for the moonroof to operate.

If you try to open the moonroof in below-f reezing temperatures, or when it is covered with snow or ice, you can damage the moonroof panel or motor.

Auto Reverse If the moonroof runs into any obstacle while it is closing automatically, it will reverse direction, and then stop. To close the moonroof, remove the obstacle, then use the moonroof switch again.

Auto reverse stops sensing when the moonroof is almost closed. You should always check that all passengers and objects are away from the moonroof before closing it.

143

2008 RDX ０７／０６／０１　１８：４９：２６　３１ＳＴＫ６１０　０１４９　

Mirrors

INDICATOR

SENSOR

AUTO BUTTON

Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving.

The inside mirror can automatically darken to reduce glare. To turn on this feature, press the button on the bottom of the mirror. The AUTO indicator comes on as a reminder. When it is on, the mirror darkens when it senses the headlights of a vehicle behind you, then returns to normal visibility when the lights are gone. Press the button again to turn off this feature.

There is also a sensor on the back of the mirror. Items hung on the mirror may block this sensor and af f ect its perf ormance.

Adjusting the Power Mirrors

SELECTOR SWITCH Turn the ignition switch to the ON (II) position.

1.

2.

Move the selector switch to L (driver’s side) or R (passenger’s side).

144

2008 RDX ０７／０６／０１　１８：４９：３５　３１ＳＴＫ６１０　０１５０　

Outside mirror positions can be stored in the driving position memory system (see page

146

).

Reverse Tilt Door Mirror The passenger outside mirror has a reverse tilt feature. When in reverse, the mirror will tilt down slightly to improve your view as you parallel park. Shifting out of reverse will return the mirror to its original position.

To tilt the passenger mirror, place the selector switch in the right position.

To turn the feature off, place the switch in the center or left position.

3.

4.

ADJUSTMENT SWITCH

Push the appropriate edge of the adjustment switch to move the mirror right, left, up, or down.

When you finish, move the selector switch to the center (off) position. This turns the adjustment switch off to keep your setting.

Mirrors

Heated Mirrors