Back

 What Did You Do On Your Car Today+ - V2.0  

Page 29 of 66
Jump to page
Post Topic
Geoff
Post #981

[IMG]http://i186.photobucket.com/albums/x107/BFG161291/jgufutdftgujkdftjukkuy.jpg[/IMG]

To start cleaning this up:

[IMG]http://i186.photobucket.com/albums/x107/BFG161291/P1010760eivbbsbvsfrvsofisdvsd.jpg[/IMG]

Chris
Post #982

Removed intake manifold to replaced a fucked valley gasket. Found an extremely dirty throttle body, black as fuck. :unsure:

Poor old thing has done that many K's, yet still runs fine.

iamhappy46
Post #983

Adjusted the Whiteline rear swaybar on the missus SH FozXT, she has an enjoyable tight rear end :wiggle:
Did yet another flash tune on the poor car, to adjust WGDC as now after 18psi peak boost and tapering off to 15psi by 4800rpm, then 12psi by 6800rpm, still on the stock subaru exhaust :dancingcool:

Pulsar is at home in the garage again... starter motor failed so pulled it out(10x easier to remove than an SR20 starter motor!) but it is an imported 6 speed box and nobody in Australia stocks this model starter motor. Hoping to patch it up with parts from auto elecs this week as having trouble finding one in the USA as well :(

S2krazie
Post #984

^ Its a VQ35 isn't it?
I would of though the starter would of been the same as a local 350Z here?

iamhappy46
Post #985

[quote name='S2krazie' timestamp='1316347571' post='1287745847']
^ Its a VQ35 isn't it?
I would of though the starter would of been the same as a local 350Z here?
[/quote]

Unfortunately, Nissan changed the design for the FWD's due to the casing being diffeent, the solenoid is diff and the internals of the FWD has a longer shaft. Even the local Maxima has a different starter motor since they are all CVT autos although this will be the first thing I look at using the check parts :(

GTS192
Post #986

Washed it.

[img]http://www.filedump.net/dumped/photo341316383944.jpg[/img]

Ben092
Post #987

Got some new struts under warranty.. Sweet beans!

E30_luv
Post #988

Put new engine mounts in, attempted to put my temp seats in till my sparco's arrive. Sliders are fucked on the drivers one. Rage quit after 30 mins, Looks like no test drive with the new LSD tonight :(

HE MAN
Post #989

Organized a trade plate for the 33, and a new front bar so I can drive the car to my guy in Redcliffe who will RWC it :)

Geoff
Post #990

Dropped the heads off to get faced and checked over.

Contemplated jumping in the engine bay again to finisg cleaning the block.....cbf.

mark1414
Post #991

[quote name='HE MAN' timestamp='1316416951' post='1287747559']
Organized a trade plate for the 33, and a new front bar so I can drive the car to my guy in Redcliffe who will RWC it :)
[/quote]

You wasted your time getting a trade plate, since you can legally drive to a place to get a RWC as long as you have CTP.

Evaded Motorsport
Post #992

Finished the turbo fitting on the Polo, have a couple of other things to do and it is good to go

HE MAN
Post #993

[quote name='mark1414' timestamp='1316417561' post='1287747596']
You wasted your time getting a trade plate, since you can legally drive to a place to get a RWC as long as you have CTP.
[/quote]
Can you really? No shit. Oh well no hassle seieng as my girlfriends dad has a Holden dealership in town and he got it from work for me

Be-Hating
Post #994

Been helping getting the stato back together.

For those who didn't see, Someone pulled out in front of him few weeks back:

[img]http://a7.sphotos.ak.fbcdn.net/hphotos-ak-snc6/216621_2156348782487_1059496572_2528097_5779542_n.jpg[/img]

[img]http://a1.sphotos.ak.fbcdn.net/hphotos-ak-ash4/206221_2156348542481_1059496572_2528096_2597372_n.jpg[/img]


Now:
Cut the gts flute/lower panel out and welded it onto the new guard
[img]http://i1133.photobucket.com/albums/m591/Joel_Cunningham/Stato/030.jpg[/img]

Cut the corner out of the new nose cone and put it onto the old one..
[img]http://i1133.photobucket.com/albums/m591/Joel_Cunningham/Stato/031.jpg[/img]

Test fitting..
[img]http://i1133.photobucket.com/albums/m591/Joel_Cunningham/Stato/035.jpg[/img]
[img]http://i1133.photobucket.com/albums/m591/Joel_Cunningham/Stato/034.jpg[/img]

Now working on cutting the rust out of the doors and other spots...

02GZM
Post #995

[quote name='iamhappy46' timestamp='1316352213' post='1287745979']
Unfortunately, Nissan changed the design for the FWD's due to the casing being diffeent, the solenoid is diff and the internals of the FWD has a longer shaft. Even the local Maxima has a different starter motor since they are all CVT autos although this will be the first thing I look at using the check parts :(
[/quote]

Doesn't happen to look like this does it?

[IMG]http://i113.photobucket.com/albums/n209/willkallis/maximastarter.jpg[/IMG]

If not, if you can gimmie a part number, some specs on the unit (measurements, no of teeth, etc.) or a pic I might be able to cross something over.

E U R E K A M A D 9 4
Post #996

Serviced the VS, realised i really badly need new rear tyres.

[img]http://a1.sphotos.ak.fbcdn.net/hphotos-ak-snc7/s720x720/298355_2337754573641_1543171647_2453641_526429252_n.jpg[/img]

So keen to get it on the road :D

S2krazie
Post #997

Just finishing spending 6hrs cleaning the exterior of the body and engine bay.
Wheels / interior and rest of engine bay tomorrow..

Sharpy
Post #998

And then you drove through a fucking massive roadworks waterway/river on the way home on the highway

E U R E K A M A D 9 4
Post

[quote name='S2krazie' timestamp='1316443557' post='1287748950']
Just finishing spending 6hrs cleaning the exterior of the body and engine bay.
Wheels / interior and rest of engine bay tomorrow..
[/quote]


i think seen you heading down Moss street yesterday arvo' ? looked the goods.

JDMNESS
Post #1000

New Braided brake lines, DBA slotted rotors and calipers on the 80
[attachment=1575194:PHOTO0887.jpg]

GTRwilson
Post #1001

Fitted new 02 sensors, and bought a new garage jack. Things a massive bitch too.

E U R E K A M A D 9 4
Post #1002

[img]http://a1.sphotos.ak.fbcdn.net/hphotos-ak-snc7/s720x720/303266_2338556073678_1543171647_2454211_377743972_n.jpg[/img]

I think i've decided to install the cooler' instead of sell it, looks sooo sexy :drool:

EssR20
Post #1003

Pretty sure you could convince you P plate mates that it's actually a PWR intercooler.

wbtonner
Post #1004

[quote name='E U R E K A M A D 9 4' timestamp='1316504267' post='1287750329']
[img]http://a1.sphotos.ak.fbcdn.net/hphotos-ak-snc7/s720x720/303266_2338556073678_1543171647_2454211_377743972_n.jpg[/img]

I think i've decided to install the cooler' instead of sell it, looks sooo sexy :drool:
[/quote]
Paint it black then red stencil the pwr logo. No one will ever know.

iamhappy46
Post #1005

[quote name='02GZM' timestamp='1316428959' post='1287748429']
Doesn't happen to look like this does it?

[IMG]http://i113.photobucket.com/albums/n209/willkallis/maximastarter.jpg[/IMG]

If not, if you can gimmie a part number, some specs on the unit (measurements, no of teeth, etc.) or a pic I might be able to cross something over.
[/quote]

Thanks :)

Completely different though. If you look at that RH end pic, the starter solenoid is actually at about the 8.30 clock position, not at 12 oclock and there is cutouts for the bellhousing bolts

Nissan Part number is: 23300 8J115
Looks like this:
[img]http://dnlauto.com/PRODIMAGES/AUTO/17830N_F.JPG[/img]

http://dnlauto.com/products.asp?cat=321&pg=12
According to this site, it is the only car it was used on.

However, maybe brushes and solenoids are interchangeable with the one you listed, as the overall body length is correct.

wolfman101
Post #1006

Plates!

[img]http://i568.photobucket.com/albums/ss126/wolfman1012003/2011-09-20121819.jpg[/img]
[img]http://i568.photobucket.com/albums/ss126/wolfman1012003/2011-09-20121850.jpg[/img]

Facelift nearly complete finally-just the nav/center stack to do.

E U R E K A M A D 9 4
Post #1007

[quote name='EssR20' timestamp='1316504439' post='1287750335']
Pretty sure you could convince you P plate mates that it's actually a PWR intercooler.
[/quote]


[quote name='wbtonner' timestamp='1316508475' post='1287750683']
Paint it black then red stencil the pwr logo. No one will ever know.
[/quote]


It's actually out of a late model GTS Commodore, it's fucking huge.

As you can see the mounting brackets are hanging below the bumper, it the top sits snug next to the radiator support.

Might do a HSV logo, not sure yet but i'll stencil it up and see if it looks tacky or not.

BlownBMW
Post #1008

ARP head and main studs, thought i'd buy her a present after 6weeks of neglect lol, taken time off to get it done now :)

clutch-monkey
Post #1009

sits better now..
[URL=http://imageshack.us/photo/my-images/98/picture7748.jpg/][IMG]http://img98.imageshack.us/img98/102/picture7748.jpg[/IMG][/URL]

VersionR
Post #1010

Nearly finished building my Celica's exhaust. Extractors (premade obviously), straight through piping, highflow lukey muff, no cat, side exit behind the passengers door.

02GZM
Post #1011

[quote name='clutch-monkey' timestamp='1316585141' post='1287752848']
sits better now..
[url="http://imageshack.us/photo/my-images/98/picture7748.jpg/"][img]http://img98.imageshack.us/img98/102/picture7748.jpg[/img][/url]
[/quote]

Which one is that? White > Purple :P

S2krazie
Post #1012

[quote name='clutch-monkey' timestamp='1316585141' post='1287752848']
sits better now..
[URL=http://imageshack.us/photo/my-images/98/picture7748.jpg/][IMG]http://img98.imageshack.us/img98/102/picture7748.jpg[/IMG][/URL]
[/quote]

That picture. Your signature. Irony :P

clutch-monkey
Post #1013

[quote name='S2krazie' timestamp='1316684775' post='1287756200']
That picture. Your signature. Irony :P
[/quote]
:lol:
i assure you the wheels fit before hand, and the new suspension was done by the shop for track use. :D new torsion bar etc was put in, stiffer rear end etc

Luke
Post #1014

Oil, oil filter and plugs on the sister's Poosar today.

E30_luv
Post #1015

Removed rear seat belts, Washed it, Polished it for the first time in over a year :)

  • Member Login

    If you have a BoostCruising account enter your user name and password into the yellow box.

    Alternatively, you can quickly login with Facebook.

    If you don't have an account create one below.

    Create Account
  • Forgotten your password?
  • Login with Facebook

    Login using your Facebook account!

Page 29 of 66
Jump to page
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
Loading...
x