Login- Download PDF Manual
-
allowed to retract fully.
5. Press the convertible seat firmly in place, let the seat belt retract and pull it taut. A sound from the seat belt retractor's auto- matic locking function will be audible at this
Ensure that the seat is securely in place
Pull out the shoulder section of the seat belt 6. Push and pull the convertible seat to
ensure that it is held securely in place by the seat belt.
WARNING
It should not be possible to move the child restraint more than 1 in. (2.5 cm) in any direction.
The convertible seat can be removed by unbuckling the seat belt and letting it retract completely.
WARNING
A child seat should never be used in the front passenger seat of any vehicle with a front passenger airbag – not even if the "Passenger airbag off" symbol near the rear-view mirror is illuminated. If the severity of an accident were to cause the airbag to inflate, this could lead to serious injury or death to a child seated in this position.
41
01 Safety
01
Booster cushions
Securing a booster cushion
Position the child correctly on the booster cushion Booster cushions are recommended for chil- dren who have outgrown convertible seats. 1. Place the booster cushion in the rear seat
of the vehicle.
2. With the child properly seated on the
booster cushion, attach the seat belt to or around the cushion according to the man- ufacturer's instructions.
3. Fasten the seat belt by inserting the latch plate into the buckle (lock) until a distinct click is audible.
Positioning the seat belt 4. Ensure that the seat belt is pulled taut and
fits snugly around the child.
WARNING
• The hip section of the three-point seat belt must fit snugly across the child's hips, not across the stomach.
• The shoulder section of the three-point seat belt should be positioned across the chest and shoulder.
• The shoulder belt must never be placed
behind the child's back or under the arm.
42
Using the ISOFIX lower child seat anchors
ISOFIX lower child restraint anchors Lower anchors for ISOFIX-equipped child seats are located in the rear, outboard seats, hidden below the backrest cushions. Symbols on the seat back upholstery mark the anchor positions as shown. To access the anchors, kneel on the seat cushion and locate the anchors by feel. Always follow your child seat manufacturer's installation instructions, and use both ISOFIX lower anchors and top tethers whenever possible.
To access the anchors 1. Put the child restraint in position.
2. Kneel on the child restraint to press down the seat cushion and locate the anchors by feel.
3. Fasten the attachment on the child
restraint's lower straps to the ISOFIX lower anchors.
4. Firmly tension the lower child seat straps according to the manufacturer's instruc- tions.
NOTE
• The rear seat's center position is not equipped with ISOFIX lower anchors. When installing a child restraint in this position, attach the restraint's top tether strap (if it is so equipped) to the top tether anchorage point and secure the restraint with the vehicle's center seat belt.
• Always follow your child seat manufac- turer's installation instructions, and use both ISOFIX lower anchors and top tethers whenever possible.
01 Safety
ISOFIX lower anchors
01
Fasten the attachment correctly to the ISOFIX lower anchors
WARNING
• Be sure to fasten the attachment cor- rectly to the anchor (see the illustration). If the attachment is not correctly fas- tened, the child restraint may not be properly secured in the event of a colli- sion.
• The ISOFIX lower child restraint
anchors are only intended for use with child seats positioned in the outboard seating positions. These anchors are not certified for use with any child restraint that is positioned in the center seating position. When securing a child restraint in the center seating position, use only the vehicle's center seat belt.
43
01 Safety
01
Top tether anchors
Child restraint anchorages
Your Volvo is equipped with child restraint top tether anchorages in the rear seat. They are located on the rear side of the backrests.
Securing a child seat 1. Place the child restraint on the rear seat. 2. Route the top tether strap under the head
restraint and attach it to the anchor.
3. Attach lower tether straps to the lower ISO- FIX/LATCH anchors. If the child restraint is not equipped with lower tether straps, or the restraint is used in the center seating position, follow instructions for securing a child restraint using the Automatic Locking Retractor seat belt (see page 35).
4. Firmly tension all straps.
44
Refer also to the child seat manufacturer's instructions for information on securing the child seat.
NOTE
On models equipped with the optional cargo area cover, this cover should be removed before a child seat is attached to the child restraint anchors.
WARNING
• Never route a top tether strap over the
top of the head restraint. The strap should be routed beneath the head restraint.
• Child restraint anchorages are designed to withstand only those loads imposed by correctly fitted child restraints. Under no circumstances are they to be used for adult seat belts or harnesses. The anchorages are not able to withstand excessive forces on them in the event of collision if full harness seat belts or adult seat belts are installed to them. An adult who uses a belt anchored in a child restraint anchorage runs a great risk of suffering severe injuries should a colli- sion occur.
• Do not install rear speakers that require the removal of the top tether anchors or interfere with the proper use of the top tether strap.
Registering a child restraint Child restraints could be recalled for safety reasons. You must register your child restraint to be reached in a recall. To stay informed about child safety seat recalls, be sure to fill out and return the registration card that comes with new child restraints. Child restraint recall information is readily avail- able in both the U.S. and Canada. For recall information in the U.S., call the U.S. Govern- ment's Auto Safety Hotline at 1-800-424-9393. In Canada, visit Transport Canada's Child Safety website at http://www.tc.gc.ca/ roadsafety/childsafety/menu.htm.
01 Safety
Child restraint registration and recalls
01
45
01 Safety
01
Integrated booster cushion
Integrated two-stage booster cushion*1
Volvo's optional integrated booster cushions are located in the outboard seating positions. These booster cushions have been specially designed to help safeguard children in the rear seat. They should be stowed (folded down into the seat cushion) when not in use. When using an integrated booster cushion, the child must be secured with the vehicle's three-point seat belt. Use these booster cushions only with children whose weight is between: • Stage 1: 48 – 80 lbs (22 – 36 kg) • Stage 2: 33 – 55 lbs (15 – 25 kg) and whose height is between: • Stage 1: 45 – 55 in. (115 – 140 cm) • Stage 2: 37 – 47 in. (95 – 120 cm) In Canada, Transport Canada's weight recommendation is 40 – 80 lbs (18 – 36 kg). The booster cushions are designed to raise the child higher, so that the shoulder strap crosses over the child's collarbone, not over the child's neck. If using a booster cushion does not resultin proper positioning of the shoulder strap, then the child should be placed in a properly secured child restraint (see page 36). The shoulder belt must never be placed behind the child's back or under the arm.
Correct seating position: child's head is below the head restraint and the shoulder belt is across the collarbone
1 Canada only: This cushion may be referred to as a built-in booster cushion.
46
* Option/accessory, for more information, see Introduction.
Incorrect seating position: the child's head is above the head restraint and the shoulder belt is not across the collarbone Before driving, check that: • The integrated two-stage booster cushion is set in the correct position for according to the child's height and weight (see the table below) and is locked in position.
Weight
Height
Stage 1
48 – 80 lbs 22 – 36 kg
Stage 2
33 – 55 lbs 15 – 25 kg
45 – 55 in. 115 – 140 cm
37 – 47 in. 95 – 120 cm
01 Safety
Integrated booster cushion
01
• That the seat belt is properly positioned
and is taut.
• The shoulder section of the seat belt is
across the child's collarbone, not over the neck.
• The lap section of the seat belt is across
the child's hips and not the abdomen.
Using an integrated booster cushion Stage 1
Pull the handle (1) forward and upward (2) to release the booster cushion. Press the booster cushion rearward to lock it in position.
Stage 2
With the booster cushion in the stage 1
position, press the button (see the arrow in illustration 1). Lift the front edge of the booster cushion and press it rearward toward the backrest to lock it in position.``
47
01 Safety
01
Integrated booster cushion
Stowing the two-stage integrated booster cushion
The booster cushion can be folded down com- pletely (stowed) from either the stage 1 or stage 2 positions.
48
NOTE
The booster cushion cannot be moved from the stage 2 (upper) position to the stage 1
(lower) position. It must first be folded down completely to the stowed position, and then adjusted to stage 1.Pull the handle forward to release the booster cushion. Press down on the center of the booster cushion to return it to the stowed position.
NOTE
The booster cushion must be in the stowed position before the rear seat backrests are folded down.
CAUTION
Be sure there are no loose objects under the booster cushion before it is stowed.
WARNING
DEATH or SERIOUS INJURY can occur Follow all instructions on the booster cushion and in the vehi- cle's owner's manual. MAKE SURE THE BOOSTER CUSHION IS SECURELY LOCKED BEFORE THE CHILD IS SEATED. • Use this booster cushion only with chil-
dren whose height and weight are within the permitted limits shown in the table see page 46.
• In the event of a collision while the inte- grated booster cushion was occupied, the entire booster cushion and seat belt must be replaced. The booster cushion should also be replaced if it is badly worn or damaged in any way. This work should be performed by a trained and qualified Volvo service technician only.
Child safety locks
Manual child safety locks – rear doors The controls are located on the rear door jambs. Use the remote control's key blade or a screwdriver to adjust these controls.
The rear doors can only be opened from the outside when the slot is in the horizon- tal position. The rear doors can be opened from the inside when the slot is in the vertical posi- tion.
01 Safety
Child safety locks
01
NOTE
There are no manual child safety locks on vehicles equipped with the optional power child safety locks.
WARNING
Remember, in the event of an accident, the rear seat passengers cannot open the doors from the inside with the controls in position A (manual child safety locks) or if the power child safety lock function is activated.
Power child safety locks* The power child lock function can be activated by pressing the button shown in the inset illus- tration above. The ignition must be in mode I or II (see page 77). When the function is activated, a message will appear in the information display and the indi- cator light in the button will light up. With the function activated: • The rear door windows can only be opened
with the control in the driver's door.
• The rear doors cannot be opened from the
inside.
* Option/accessory, for more information, see Introduction.
49
Remote key and key blade..................................................................... 52
Private locking ........................................................................................ 59
Keyless drive........................................................................................... 60
Locks....................................................................................................... 63
Alarm....................................................................................................... 6550
LOCKS AND ALARM
02
02 Locks and alarm
Remote key and key blade
Introduction Two remote keys or optional Personal Car Communicators (PCC) are provided with your vehicle. They enable you to unlock the doors and tailgate, and also function as ignition keys to start the vehicle or operate electrical com- ponents. The remote keys contain detachable metal key blades for manually locking or unlocking the driver's door and the glove com- partment. Up to six remotes can be pro- grammed for use on the same vehicle. The PCCs have enhanced functionality com- pared with the standard remote key.
NOTE
In the remainder of this chapter, all referen- ces to the remote key also pertain to the PCC unless otherwise stated.
WARNING
Never leave the remote key in the ignition if children are to remain in the vehicle.
Detachable key blade Each remote key or PCC contains a detachable metal key blade for mechanically locking or unlocking the driver's door and the glove com- partment, and to enable the private locking function. See page 57 for more information on the key blade and page 59 for information
02
52
on the private locking function. The key blades have a unique code, which is used if new ones need to be produced. This code is available at an authorized Volvo retailer.
Car key memory
Loss of a remote key If a remote key is lost, the other one must be taken with the vehicle to a trained and qualified Volvo service technician. As an anti-theft measure, the code of the lost remote must be erased from the system. The number of registered keys for the vehicle can be found in the vehicle's menu under Car Number of settings keys. See page 120 for a description of the menu system. USA-5WK49264
FCC ID:KR55WK49264 + Siemens VDO 5WK49236
FCC ID:KR55WK49236, 5WK49266
FCC ID:KR55WK49266 + Siemens VDO 5WK49233
FCC ID:KR55WK49233
This device complies with part 15 of the FCC rules and RSS-210. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, includ-ing interference that may cause undesired operation. Canada-5WK49264
IC:267T-5WK49264 + Siemens VDO 5WK49236
IC:267T-5WK49236, 5WK49266
IC:267T-5WK49266 + Siemens VDO 5WK49233
IC:267T-5WK49233
Operation is subject to the following condi- tions: (1) this device may not cause interfer- ence, and (2) this device must accept any inter- ference, including interference that may cause undesired operation of the device.Key memory – door mirrors and driver's seat The position of the side door mirrors and optional power driver's seat are stored in the remote keys when the vehicle is locked. The next time the driver's door is unlocked with the same remote key and the door is opened within 2 minutes, the power driver's seat and side door mirrors will automatically move to the position that they were in when the doors were most recently locked with the same remote key. See page 80 for more information.
Immobilizer (start inhibitor) Each of the keys supplied with your vehicle contains a coded transponder. The code in the key is transmitted to an antenna in the ignition slot where it is compared to the code stored in the start inhibitor module. The vehicle will start only with a properly coded key. If you misplace a key, take the other keys to a trained and qualified Volvo service technician for reprog- ramming as an antitheft measure. The follow- ing messages (which may appear in the instru- ment panel display) are related to the immobil- izer:
This feature can be activated or deactivated in the vehicle's menu under Car settings Car Seat & mirror positions. See key memory page 120 for a description of the menu sys- tem. See also page 60 for information regarding vehicles with the optional keyless drive.
Confirmation when locking/unlocking the vehicle When the vehicle is locked with a remote key, the turn signals will flash once to confirm that this has been completed correctly. When the vehicle is locked, confirmation will only be given if all of the locks are locked after the doors have been closed.
NOTE
If you do not receive confirmation when locking the vehicle, check whether a door or the tailgate is ajar, or if this feature has been turned off in the menu.
This function can be activated or deactivated under Car settings Lock Light settings confirmation, light, or Car settings Light Unlock confirmation, light. See settings page 120 for a description of the menu sys- tem.
02 Locks and alarm
Remote key and key blade
Message
Meaning
Key error Reinsert key
Car key Not found
Immobilizer See manual
Remote key not rec- ognized during start. Try to start the vehi- cle again.
PCC with keyless drive only. Remote key not recognized during start. Try to start the vehicle again.
Remote key fault during start. Contact an authorized Volvo workshop.
CAUTION
Never use force when inserting the remote key in the ignition slot. The vehicle cannot be started if the transponder is damaged.
USA–FCC ID: LTQWFS 125VO This device complies with part 15 of the FCC rules. Operation is subject to the following con- dition: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interfer- ence that may cause undesired operation.
02
``
53
02
02 Locks and alarm
Remote key and key blade
Canada–IC: 3659A-WFS125VO Operation is subject to the following condi- tions: (1) this device may not cause interfer- ence, and (2) this device must accept any inter- ference, including interference that may cause undesired operation of the device. See page 103 for information on starting the vehicle.
Replacing the battery in the remote key The batteries should be replaced if: • The information symbol illuminates and
Replace car key battery is shown in the display and/or
• if the locks do not react after several
attempts to unlock or lock the vehicle.
NOTE
The remote key's range is normally approx- imately 60 ft (20 m) from the vehicle.
See page 57 for information on replacing the battery.
Common functions – Remote key/ Personal Car Communicator (PCC)
Remote key
Personal Car Communicator (PCC)*
Lock
Unlock
Approach lighting
Tailgate unlock/open
Panic alarm
Information
Buttons on the remote Lock – Press the Lock button on the remote once to lock all doors and the tailgate. The turn signals will flash once to confirm locking. Unlock – Press the Unlock button on the remote once to unlock the driver's door. After a short pause, press the Unlock button a second time within 10 seconds to unlock the other doors and the tailgate. This function can be changed so that all doors unlock at the same time under Car settings
lock settings
Doors, unlock. See page
120 for a description of the menu system. Approach lighting – As you approach the vehicle, press the button on the remote key to light the interior lighting, parking lights, license plate lighting and the lights in the door mir- rors*. These lights will switch off automatically after 30, 60 or 90 seconds, see page 120 for more information.
54
* Option/accessory, for more information, see Introduction.
To deactivate, wait approximately 5 seconds and press the button again. These lights will switch off automatically after 30, 60 or 90 seconds, see page 120 for more information. The Panic alarm button will not unlock the vehi- cle.
Range The remote key has a range of approximately 60 ft. (20 m) from the vehicle.
NOTE
Buildings or other obstacles may interfere with the function of the remote key. The vehicle can also be locked or unlocked with the key blade, see page 57.
Unlock tailgate – Press the button once to disarm the alarm system and optional move- ment sensor (the alarm indicator light on the dashboard will go out), and unlock only the tailgate.
NOTE
• Pressing this button for several seconds
also opens the tailgate on models equipped with the optional power tail- gate.
• As an added safety precaution, the
parking lights will come on automati- cally for a short period when the tailgate has been opened.
After closing, the tailgate will not automatically relock. Press Lock to relock it and rearm the alarm. See also the section "Unlocking the tailgate from the passenger compartment. Panic alarm – This button can be used to attract attention during emergency situations. To activate the panic alarm, press and hold this button for at least 3 seconds or press it twice within 3 seconds. The turn signals and horn will be activated. The panic alarm will stop auto- matically after 2 minutes and 45 seconds.
02 Locks and alarm
Remote key and key blade
Functions – PCC
02
Information button
Indicator lights
Pressing the information button provides cer- tain information about the vehicle with the help of the indicator lights.
Using the information button 1. Press the information button 2. All of the indicator lights will flash sequen- tially for approximately 7 seconds to indi- cate that the PCC is receiving information from the vehicle. If any of the buttons are pressed during this 7-second period, transmission of information to the PCC will be interrupted.
``
55
02 Locks and alarm
Remote key and key blade
NOTE
02
If none of the indicator lights flash when the information button has been pressed sev- eral times from different places in relation to the vehicle, contact an authorized Volvo service technician.
The indicator lights according to the illustration:
provide information
Steady green light: the vehicle is correctly locked. Steady yellow light: the vehicle is not locked. Alternatively flashing red lights (Heartbeat sensor): if the two heartbeat sensor lights flash, this indicates that someone may be
56
inside the vehicle. These lights are only activated if the alarm has been triggered. Steady red light: the alarm has been trig- gered.
Range The PCC's lock and unlock functions have a range of approximately 60 ft. (20 m) from the vehicle.
NOTE
• The approach lighting, panic alarm, and the functions controlled by the informa- tion button have a range of approxi- mately 300 ft (100 m) from the vehicle. • Buildings or other obstacles may inter-
fere with the function of the PCC.
Outside of the PCC´s range If the PCC is more than approximately 300 ft (100 m) from the vehicle when the information button is pressed, no new information will be received. The PCC most recently used to lock or unlock the vehicle will show the vehicle's most recently received status. The indicator lights will not flash when the information button is pressed while the PCC is out of range.
If more than one PCC is used to lock/unlock the vehicle, only the one used most recently will show the correct locking status.
NOTE
If none of the indicator lights illuminate when the information button is pressed, this may be because the most recent transmission between the vehicle and the PCC was inter- rupted or impeded by buildings or other objects.
Heartbeat Sensor is a comple- The heartbeat sensor function ment to the vehicle's standard alarm, and indi- cates at a distance of up to 300 ft (100 m) that someone may be in the vehicle. The heartbeat sensor only functions if the alarm has been triggered.
NOTE
The heartbeat sensor registers a person's heartbeat in the form of vibrations in the vehicle's chassis. For this reason, the sen- sor's function may be impaired in areas with high levels of noise or vibrations.
Keyless drive Vehicles equipped with the optional Personal Car Communicator have the keyless drive
function, see page 60 for detailed informa- tion.
Detachable key blade The key blade can be removed from the remote key. When removed, the key blade can be used as follows: • To lock/unlock the driver's door • To lock/unlock the glove compartment
(see page 63)
• To enable/disable the private locking func-
tion (see page 59)
Unlocking the doors with the detached key blade Insert the key blade as far as possible in the driver's door lock. Turn the key blade clock- wise approximately one-quarter turn to unlock the driver's door only.
NOTE
After unlocking the driver's door with the key blade, opening the door will trigger the alarm.
To disable the alarm: Insert the remote key in the ignition slot.
Locking the doors with the detached key blade 1. Lock the rear doors and the front passeng-
er's door by pressing the lock button on each door.
2. Turn the key blade one-quarter turn coun-
ter-clockwise to lock the driver's door.
Removing the key blade
Slide the spring loaded catch to the side.
Pull the key blade straight out of the remote key.
Reinserting the key blade in the remote key 1. Hold the remote key with the slot for the
key blade up.
2. Carefully slide the key blade into its groove.
02 Locks and alarm
Remote key and key blade
3. Gently press the key blade in the groove
until it clicks into place.
02
Replacing batteries in the remote key/ PCC The battery/batteries in the remote key/PCC should be replaced if: • The information symbol lights up and a text
is shown in the information display.
and/or • the vehicle's locks repeatedly do not react when a button on the remote key/PCC is pressed within approximately 60 ft (20 m) from the vehicle.
``
57
02 Locks and alarm
Remote key and key blade
NOTE
Turn the remote key with the buttons upward so that the batteries do not fall out when the cover is removed.
Replacing the batteries
CAUTION
When handling batteries, avoid touching their contact surfaces as this could result in poor battery function in the remote key.
Note the position of the battery's (+) or (–) sides.
Re-assembling the remote key 1. Press the remote key's cover into place. 2. Hold the remote key with the slot for the
key blade up.
3. Carefully slide the key blade into its groove. 4. Gently press the key blade in the groove
until it clicks into place.
Old batteries should be properly recycled.
Battery type CR 2430, 3 V (one battery in the remote key, two batteries in the PCC)
2.
Opening the remote key/PCC
Slide the spring loaded catch to the
side.
Pull the key blade straight out of the
remote key.
Insert a small screwdriver in the hole
behind the spring loaded catch and care- fully pry up the cover.
2.
3.
Remote key (one battery) 1. Use a screwdriver to pry out the old bat-
tery. Insert a new one with the (+) side down- ward.
PCC (two batteries) 1. Use a screwdriver to pry out the old bat-
teries. Insert the first new battery with the (+) side upward. Insert the plastic spacer over the battery. Insert the second new battery on top of the plastic spacer, with the + side downward.
02
58
Tailgate compartment
Normal locking/unlocking points
Locking/unlocking points with private locking acti- vated. By utilizing the remote key with the key blade removed, the private locking feature enables you to block access to the glove compartment
and disconnect the tailgate from the central locking system for e.g., valet parking or when the vehicle is brought to the retailer for service. With the private locking function activated: • The vehicle's doors can be locked or
unlocked with the remote • The engine can be started • The glove compartment cannot be
unlocked
• The tailgate cannot be unlocked or opened
with the remote
• The rear floor hatch cannot be opened Activating the private locking function
Insert the key blade in the glove compart- ment lock. Turn the key blade180 degrees clockwise.
02 Locks and alarm
Private locking
Remove the key blade from the lock. A message will appear in the instrument panel display.
02
Deactivating the private locking function Turn the key blade 180 degrees counterclock- wise in the glove compartment lock to deacti- vate private locking. See page 63 for information on locking the glove compartment normally, without activat- ing the private locking function.
59
02 Locks and alarm
Keyless drive
02
Keyless drive (models with Personal Car Communicator only)
Keyless locking and unlocking
Range of the keyless drive remote key–5 ft (1.5 meters) This system makes it possible to unlock and lock the vehicle without having to press any buttons on the Personal Car Communicators (PCC). It is only necessary to have a keyless drive remote key in your possession to operate the central locking system.
NOTE
The buttons on the keyless drive remote key can also be used to lock and unlock the vehicle, see page 54 for more information.
60
Both of the PCCs provided with the vehicle have the keyless function, and additional ones can be ordered. The system can accommo- date up to six PCCs. The red rings in the illustration indicate the area around the vehicle covered by the keyless drive antennas.
Unlocking the vehicle • A keyless drive remote key must be on the same side of the vehicle as the door to be opened, and be within 5 feet (1.5 meters) of the lock or the tailgate (see the shaded areas in the illustration).
• Pull a door handle to unlock and open the
door or pull the tailgate opening control. The number of doors that are unlocked at the same time can be set in the vehicle's menu system, under Car settings
Lock settings Keyless entry. See page 120 for a descrip-
tion of the menu system.
NOTE
If the PCC does not function normally (weak battery, etc.), the vehicle can be unlocked with the detachable key blade, see page 57.
Locking the vehicle The doors and the tailgate can be locked by pressing the lock button in any of the outside door handles.
NOTE
On keyless drive vehicles, the gear selector must be in the Park (P) position, all doors and the tailgate must be closed and the igni- tion must be switched off before the vehicle can be locked.
Keyless drive remote key and driver's seat/door mirror memory • When you leave the vehicle with a PCC in
your possession and lock any door, the position of the driver's seat will be stored in the seat's memory.
• The next time a door is opened by a person with the same PCC in his/her possession, the driver's seat and door mirrors will auto- matically move to the position that they were in when the door was most recently locked.
NOTE
If several people carrying PCCs approach the vehicle at the same time, the driver's seat and door mirrors will assume the posi- tions they were in for the person who opens the driver's door.
See also page 80 for information on adjusting and storing the seat's position in the seat mem- ory.
Keyless drive information messages If all of the PCCs are removed from the vehicle while the engine is running or if the ignition is in mode II and all of the doors are closed, a message will appear in the instrument panel display and an audible signal will sound. When at least one PCC has been returned to the car, the message will be erased in the dis- play and the audible signal will stop when: • A door has been opened and closed • The PCC has been inserted in the ignition
slot
• The READ button (see page 122 for the
location of this button) has been pressed.
CAUTION
• Keyless drive remote keys should never
be left in the vehicle. In the event of a break-in, a remote found in the vehicle could make it possible to start the engine.
• Electromagnetic fields or metal
obstructions can interfere with the key- less drive system. Avoid placing the remote key near cellular phones, metal- lic objects or e.g., in a metal briefcase.
USA – FCC ID:KR55WK48952, KR55WK48964
NOTE This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept interference received, including inter- ference that may cause undesired operation. CAUTION Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. Siemens VDO 5WK48891
Tested To Comply With FCC Standards02
02 Locks and alarm
Keyless drive
For Automobile Use Canada – IC:267T-5WK48952, 267T-5WK48964, 267T-5WK48891
NOTE This device complies with RSS -210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept interference received, including inter- ference that may cause undesired operation. CAUTION Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.Location of the keyless drive antennas
``
61
02 Locks and alarm
Keyless drive
The keyless drive system has a number of antennas located at various points in the vehi- cle.
02
On the tailgate, near the wiper motor
Left rear door handle
Ceiling, above the center of the rear seat
Under the floor of the cargo area, near the rear seat Right rear door handle
Under the rear section of the center con- sole Under the front section of the center con- sole.
WARNING
People with implanted pacemakers should not allow the pacemaker to come closer than 9 inches (22 cm) to any of the keyless drive system's antennas. This is to help pre- vent interference between the pacemaker and the keyless drive system.
62
Locking and unlocking the vehicle
From inside the vehicle
From outside the vehicle The remote key locks all of the doors and the tailgate. If the locks repeatedly do not react when the unlock button is pressed, it may be necessary to replace the batteries in the remote, see page 54. In this case the vehicle can be unlocked with the detachable key blade. See page 57 for information on removing the key blade from the remote key. The first press on the unlock button unlocks the driver's door and a second press unlocks the other doors and the tailgate (see also page 54).
NOTE
The vehicle cannot be locked if a door is open.
The lock buttons on the door panel can be used to lock or unlock all doors and the tailgate at the same time. Unlocking ± Press the unlock button. Locking ± Press the lock button after the front doors
have been closed.
• Each door can be locked individually with the lock button on the respective doors. The door must be closed first.
• The door can be unlocked by pulling the door handle once and opened by pulling the handle again.
02 Locks and alarm
Locks
Automatic relocking If the doors are unlocked, the locks will auto- matically reengage (re-lock) and the alarm will rearm after 2 minutes unless a door or the tail- gate has been opened.
Automatic locking When the vehicle starts to move, the doors and tailgate can be locked automatically. This fea- ture can be turned on or off under Car settings Doors automatic lock. See page 120 for a description of the menu system.
Lock settings
Glove compartment
The glove compartment can only be locked and unlocked using the detachable key blade in the remote key. See page 57 for information
02
``
63
02 Locks and alarm
Locks
on removing the key blade from the remote key.
02
Insert the key blade in the glove compart- ment lock. Turn the key blade 90 degrees clockwise.
> The alarm indicator light on the dash- board will go out to indicate that the alarm is not monitoring the entire vehi- cle. The accessory movement and incli- nation sensors will be automatically dis- connected.
Remove the key blade from the lock.
NOTE
Unlocking the tailgate from the passenger compartment
Locking/unlocking the tailgate
Tailgate unlock button on the remote key Unlocking the tailgate with the remote key ± Press the tailgate unlock button on the remote key to unlock (but not open1) the tailgate. See also page 54.
• If the doors are locked while the tailgate
is open, the tailgate will remain unlocked until the vehicle is relocked by pressing the Lock button on the remote key.
• On keyless drive vehicles, the gear
selector must be in the Park (P) position, all doors and the tailgate must be closed and the ignition must be switched off before the vehicle can be locked.
Locking the tailgate with the remote key ± Press the lock button on the remote. See
also page 54.
± Press the button on the lighting panel (1) to
unlock (but not open1) the tailgate.
NOTE
The taillights will illuminate automatically for a short period when the tailgate has been opened.
1 This button also opens, but does not close, the tailgate on models equipped with the optional power tailgate (see page 200).
64
The alarm system The alarm is automatically armed whenever the vehicle is locked with the remote key or optional Personal Car Communicator. When armed, the alarm continuously monitors a number of points on the vehicle. The follow- ing conditions will trigger the alarm: • The hood is forced open. • The tailgate is forced open. • A door is forced open. • The ignition slot is tampered with. • An attempt is made to start the vehicle with
a non-approved key (a key not coded to the car's ignition).
• If there is movement in the passenger com-
partment (if the vehicle is equipped with the accessory movement sensor).
• The vehicle is lifted or towed (if the vehicle is equipped with the accessory inclination sensor).
• The battery is disconnected (while the
alarm is armed).
• The siren is disconnected when the alarm
is disarmed.
A message will appear in the information dis- play if a fault should occur in the alarm system. Contact an authorized Volvo service techni- cian.
NOTE
Do not attempt to repair any of the compo- nents in the alarm system yourself. This could affect the insurance policy on the vehicle.
The alarm indicator light
The status of the alarm system is indicated by the indicator light on the dashboard (see illus- tration): • Indicator light off – the alarm is not armed • The indicator light flashes at one-second
intervals – the alarm is armed
• The indicator light flashes rapidly before the remote key is inserted in the ignition slot – the alarm has been triggered.
02 Locks and alarm
Alarm
Arming the alarm ± Press the Lock button on the remote key. One long flash of the turn signals will con- firm that the alarm is armed.
Lock settings
Alarm confirmation settings can be changed under Car settings Keyless entry. See page 120 for a description of the menu system. USA FCC ID: MAYDA 5823(3) This device complies with part 15 of the FCC rules. Operation is subject to the following con- ditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interfer- ence that may cause undesired operation. Canada IC: 4405A-DA 5823(3) Movement sensor DA5823 by Dynex Operation is subject to the following conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired opera- tion of the device.
02
``
65
4. Press ENTER and lock the vehicle. The next time the engine is started, the alarm system will be reset and Full guard will appear in the instrument panel display. The accessory inclination and movement alarm sensors will be reactivated. In either of the alternatives, if you prefer not to deactivate the accessory inclination and move- ment alarm sensors, do not make a choice in the menu or press EXIT and lock the vehicle.
02 Locks and alarm
Alarm
02
67
Instruments and controls........................................................................ 70
Ignition modes........................................................................................ 77
Seats....................................................................................................... 79
Steering wheel........................................................................................ 84
Lighting................................................................................................... 85
Wipers and washers................................................................................ 91
Power windows....................................................................................... 94
Mirrors..................................................................................................... 96
Power moon roof* .................................................................................. 98
HomeLink® Wireless Control System*................................................. 100
Starting the engine................................................................................ 103
Transmission......................................................................................... 107
Brakes................................................................................................... 110
Hill Descent Control (HDC)................................................................... 112
Parking brake........................................................................................ 11468
* Option/accessory, for more information, see Introduction.
YOUR DRIVING ENVIRONMENT
03
03 Your driving environment
Instruments and controls
Instrument overview
03
70
Page
120, 88, 85, 151
157
84, 20
71
131
77
77
88
–
94, 96, 49, 63
Function
Menus and mes- sages, turn signals, high/low beams, trip computer
Cruise control
Horn, airbag
Main instrument panel
Menu system, audio controls
Ignition slot
START/STOP ENGINE button
Hazard warning flashers
Door handle
In-door control pan- els (power win- dows, mirrors, power child safety locks, central lock- ing button)
Function
Menu controls, audio and climate control systems
Center console but- tons
Gear selector
Controls for active chassis (Four-C) - certain models only
Page
120, 132, 126
120
107
156
Wipers and washers
91, 92
84
114
217
79
85, 198, 64
Steering wheel adjustment
Parking brake
Hood opening con- trol
Power seat* adjust- ment controls
Lighting panel, but- tons for opening fuel filler door and unlocking the tail- gate
03 Your driving environment
Instruments and controls
Information displays
03
Information displays in the instrument panel The information displays (1) show information on some of the vehicle's functions, such as cruise control, the trip computer and mes- sages. The information is shown with text and symbols. More detailed information can be found in the descriptions of the functions that use the infor- mation displays.
* Option/accessory, for more information, see Introduction.
``
71
03 Your driving environment
Instruments and controls
Gauges
Indicator, information, and warning symbols
03
Gauges in the instrument panel
Speedometer
Fuel gauge. Please note that the fuel level indicator in the gauge moves from right to left as the amount of fuel in the tank decreases. See also the section on refuel- ing beginning on page 196. See page 151 for more information on fuel level and consumption. The tachometer shows engine speed in thousands of revolutions per minute (rpm). Do not drive continuously with the needle in the red area of the gauge. The engine management system will automatically prevent excessively high engines speeds. This will be noticeable as a pronounced unevenness in engine speed.
Indicator and warning symbols
Indicator and information symbols
Indicator and warning symbols
High beam and turn signal indicators
Function check All indicator and warning symbols light up in ignition mode II or when the engine is started. When the engine has started, all the symbols should go out except the parking brake sym- bol, which only goes out when the brake is dis- engaged. If the engine does not start or if the function check is carried out in ignition mode II, all sym- bols go out after 5 seconds except the symbol
72
* Option/accessory, for more information, see Introduction.
for faults in the vehicle's emissions system and the symbol for low oil pressure. Certain symbols may not have their functions illustrated, depending on the vehicle's equip- ment.
Indicator and information symbols
Symbol
Description
Fault in the Active Bending Light (ABL)*system
Malfunction indicator light
Anti-lock brake system (ABS)
Rear fog light on
Stability system
Tire pressure monitoring sen- sor (TPMS)
Low fuel level
Information symbol, see text in information display
High beam indicator
03 Your driving environment
Symbol
Description
Left turn signal indicator
Right turn signal indicator
Fault in the Active Bending Light
(ABL) system This symbol will illuminate if the there is a fault in the ABL system.
Malfunction Indicator Light
As you drive, a computer called On-Board Diagnostics II (OBDII) monitors your vehicle's engine, transmission, electrical and emission systems. The malfunction indicator (CHECK ENGINE) light will illuminate if the computer senses a condition that potentially may need correcting. When this happens, please have your vehicle checked by a trained and qualified Volvo serv- ice technician as soon as possible. A malfunction indicator (CHECK ENGINE) light may have many causes. Sometimes, you may not notice a change in your car's behavior. Even so, an uncorrected condition could hurt fuel economy, emission controls, and drivabil- ity. Extended driving without correcting the
cause could even damage other components in your vehicle. This light may illuminate if the fuel filler cap is not closed tightly or if the engine was running while the vehicle was refueled.
Canadian models are equipped with this
symbol.
Anti-lock Brake System (ABS)
warning light If the warning light comes on, there may be a malfunction in the ABS system (the standard braking system will still function). Check the system by: 1. Stopping in a safe place and switching off
the ignition.
2. Restart the engine. 3.
If the warning light goes off, no further action is required.
If the warning light remains on, the vehicle should be driven to a trained and qualified Volvo service technician for inspection, see page 110 for additional information.
Canadian models are equipped with this
symbol.
03
Instruments and controls
Rear fog light
This symbol indicates that the rear fog light (located in the driver's side tail light cluster) is on.
Stability system
This indicator symbol flashes when the DSTC (Dynamic Stability and Traction Control sys- tem) is actively working to stabilize the vehicle, see page 154 for more detailed information. Tire pressure monitoring system
(TPMS)* This symbol illuminates to indicate that tire pressure in one or more tires is low, see page 260 for detailed information.
Low fuel level
When this light comes on, the vehicle should be refueled as soon as possible.
Information symbol
The information symbol illuminates and a text message is displayed if a fault is detected in one of the vehicle's systems. The message can be erased and the symbol can be turned off by pressing the READ button (see page 122 for information) or this will take place automatically after a short time (the length of time varies, depending on the function affected). The information symbol may also illuminate together with other symbols.
* Option/accessory, for more information, see Introduction.
``
73
03 Your driving environment
Instruments and controls
High beam indicator
This symbol illuminates when the high beam headlights are on, or if the high beam flash function is used.
03
Left turn signal indicator
Right turn signal indicator
Symbol Description
Generator not charging
Fault in the brake system
Warning symbol
NOTE
• Both turn signal indicators will flash
when the hazard warning flashers are used.
• If either of these indicators flash faster than normal, the direction indicators are not functioning properly.
Indicator and warning symbols
Symbol Description
Low oil pressure
Parking brake applied
SRS airbags
Seat belt reminder
Low oil pressure
If the light comes on while driving, stop the vehicle, stop the engine immediately, and check the engine oil level. If the oil level is nor- mal and the light stays on after restart, have the vehicle towed to the nearest trained and quali- fied Volvo service technician. This is normal, provided it goes off when the engine speed is increased.
Parking brake applied
This symbol illuminates when the parking brake is applied. On models equipped with the electric parking brake, this symbol flashes while the brake is being applied and then glows steadily. A flashing symbol means that a fault has been detected. See the message in the information display.
74
Canadian models are equipped with this
symbol.
NOTE
This symbol also comes on when the mechanical parking brake is only slightly applied.
Airbags – SRS
If this light comes on while the vehicle is being driven, or remains on for longer than approxi- mately 10 seconds after the vehicle has been started, the SRS system's diagnostic functions have detected a fault in a seat belt lock or pre- tensioner, a front airbag, side impact airbag, and/or an inflatable curtain. Have the system(s) inspected by a trained and qualified Volvo service technician as soon as possible.
Seat belt reminder
This symbol comes on for approximately 6 sec- onds if the driver has not fastened his or her seat belt.
Generator not charging
This symbol comes on during driving if a fault has occurred in the electrical system. Contact an authorized Volvo workshop. Engine temperature Engine overheating can result from low oil or coolant levels, towing or hard driving at high
03 Your driving environment
heat and altitude, or mechanical malfunction. Engine overheating will be signaled with text and a red warning triangle in the middle of the instrument display. The exact text will depend on the degree of overheating. It may range from "HIGH ENGINE TEMP – SLOW DOWN" to "HIGH ENGINE TEMP – STOP ENGINE." If appropriate, other messages, such as "COOLANT LEVEL LOW" will also be displayed. If your engine does overheat so that you must stop the engine, always allow the engine to cool before attempting to check oil and coolant levels.
Fault in brake system
If this symbol lights, the brake fluid level may be too low. Stop the vehicle in a safe place and check the level in the brake fluid reservoir, see page 220. If the level in the reservoir is below MIN, the vehicle should be transported to an authorized Volvo workshop to have the brake system checked.
Canadian models are equipped with this
symbol.
and
symbols come on at the
If the same time, there may be a fault in the brake force distribution system. 1. Stop the vehicle in a safe place and turn off
the engine.
2. Restart the engine.
• If both symbols extinguish, continue driv-
ing.
• If the symbols remain on, check the level in the brake fluid reservoir, see page 220. If the brake fluid level is normal but the sym- bols are still lit, the vehicle can be driven, with great care, to an authorized Volvo workshop to have the brake system checked.
• If the level in the reservoir is below MIN, the vehicle should be transported to an author- ized Volvo workshop to have the brake system checked.
WARNING
• If the fluid level is below the MIN mark in the reservoir or if a warning message is displayed in the text window: DO NOT DRIVE. Have the vehicle towed to a trained and qualified Volvo service technician and have the brake system inspected.
• If the ABS and Brake system lights are on at the same time, there is a risk of reduced vehicle stability.
Warning symbol
The red warning symbol comes on when a fault has been indicated which could affect the safety and/or drivability of the vehicle. An
Instruments and controls
explanatory text is shown on the information display at the same time. The symbol remains visible until the fault has been rectified but the text message can be cleared with the READ button, see page 122. The warning symbol can also come on in conjunction with other sym- bols. Action: 1. Stop in a safe place. Do not drive the vehi-
cle further.
2. Read the information on the information display. Implement the action in accord- ance with the message in the display. Clear the message using READ.
Reminder – doors not closed If one of the doors, the hood or tailgate is not closed properly, the information or warning symbol comes on together with an explanatory text message in the instrument panel. Stop the vehicle in a safe place as soon as possible and close the door, hood or tailgate.
If the vehicle is driven at a speed lower than approximately 5 mph
(7 km/h), the information symbol comes on. If the vehicle is driven at a speed higher than approximately 5 mph
(7 km/h), the warning symbol comes on.
03
``
75
03 Your driving environment
Instruments and controls
Trip odometers
Clock
