2010 Volvo C30 Owners Manual

Download PDF Manual
08 Car care 08 203 Volvo maintenance................................................................................ 206 Maintaining your car............................................................................. 208 Hood..................................................................................................... 210 Engine compartment............................................................................. 211 Engine oil............................................................................................... 212 Fluids..................................................................................................... 214 Wiper blades......................................................................................... 216 Battery................................................................................................... 217 Replacing bulbs.................................................................................... 219 Fuses..................................................................................................... 227 204 MAINTENANCE AND SERVICING 09 09 Maintenance and servicing 09 Volvo maintenance General Volvo advises you to follow the maintenance program outlined in the Warranty and Service Records Information booklet. This mainte- nance program contains inspections and serv- ices necessary for the proper function of your vehicle. The maintenance services contain several checks that require special tools and training, and therefore must be performed by a qualified technician. To keep your Volvo in top condition, specify time-tested and proven Genuine Volvo Parts and Accessories. The Federal Clean Air Act – U.S The Federal Clean Air Act requires vehicle manufacturers to furnish written instructions to the ultimate purchaser to assure the proper servicing and function of the components that control emissions. These services, which are listed in the "Warranty and Service Records Information" booklet, are not covered by the warranty. You will be required to pay for labor and material used. Maintenance Your Volvo passed several major inspections before it was delivered to you, in accordance with Volvo specifications. The maintenance procedures outlined in the Warranty and Serv- ice Records Information booklet, many of which will positively affect your vehicle's emis- sions, should be performed as indicated. It is recommended that receipts for vehicle emis- sion maintenance be retained in case ques- tions arise concerning maintenance. Inspec- tion and maintenance should also be per- formed anytime a malfunction is observed or suspected. Applicable warranties – U.S/Canada In accordance with applicable U.S. and Cana- dian regulations, the following list of warranties is provided. • New Vehicle Limited Warranty • Parts and Accessories Limited Warranty • Corrosion Protection Limited Warranty • Seat Belt and Supplemental Restraint Sys- tems Limited Warranty • Emission Design and Defect Warranty • Emission Performance Warranty These are the federal warranties; other warran- ties are provided as required by state/provin- cial law. Refer to your separate Warranty and Service Records Information booklet for detailed information concerning each of the warranties. Periodic maintenance helps minimize emissions Periodic maintenance will help keep your vehi- cle running well. Your Warranty and Service Records Information booklet provides a com- prehensive periodic maintenance schedule up to 150,000 miles (240,000 km) of vehicle main- tenance. The schedule includes components that affect vehicle emissions. This page describes some of the emission-related com- ponents. Vehicle Event Data (Black Box) Your vehicle's driving and safety systems employ computers that monitor, and share with each other, information about your vehi- cle's operation. One or more of these comput- ers may store what they monitor, either during normal vehicle operation or in a crash or near- crash event. Stored information may be read and used by: • Volvo Car Corporation • service and repair facilities 206 09 Maintenance and servicing Volvo maintenance 09 • law enforcement or government agencies • others who may assert a legal right to know, or who obtain your consent to know such information. 207 09 Maintenance and servicing 09 Maintaining your car As needed: • Wash the car, including the undercarriage, to reduce wear that can be caused by a buildup of dirt, and corrosion that can be caused by salt residues. • Clean leaves and twigs from air intake vents at the base of the windshield, and from other places where they may collect. NOTE Complete service information for qualified technicians is available online for purchase or subscription at www.volvotechinfo.com. Hoisting the vehicle If a garage jack is used to lift the vehicle, the two jack attachments points should be used. They are specially reinforced to bear the weight of the vehicle. A garage jack can also be placed under the front of the engine support frame. Take care not to damage the splash guard under the engine. Ensure that the jack is posi- tioned so that the vehicle cannot slide off it. Always use axle stands or similar structures. If a two-post hoist is used to lift the vehicle, the front and rear lift arm pads should be centered under the reinforced lift plates on the inboard edge of the sill rail (see illustration). Emission inspection readiness What is an Onboard Diagnostic System (OBD II)? OBD II is part of your vehicle's computerized engine management system. It stores diagnos- tic information about your vehicle's emission controls. It can light the Check Engine light (MIL) if it detects an emission control "fault." A "fault" is a component or system that is not performing within an expected range. A fault may be permanent or temporary. OBD II will store a message about any fault. Owner maintenance Periodic maintenance requirements and inter- vals are described in your vehicle's Warranty and Service Records Information booklet. The following points can be carried out between the normally scheduled maintenance services. Each time the car is refueled: • Check the engine oil level. • Clean the windshield, windshield wipers, headlights, and taillights. Monthly: • Check cold tire pressure in all tires. Inspect the tires for wear. • Check that engine coolant and other fluid levels are between the indicated "min" and "max" markings. • Clean interior glass surfaces with a glass cleaner and soft paper towels. • Wipe driver information displays with a soft cloth. • Visually inspect battery terminals for cor- rosion. Corrosion may indicate a loose ter- minal connector, or a battery near the end of its useful service life. Consult a trained and qualified Volvo service technician for additional information. 208 09 Maintenance and servicing Maintaining your car 09 your vehicle diagnosed and, if necessary, serviced by a qualified Volvo technician. • If you recently had service for a lit Check Engine light, or if you had service that required disconnecting the battery, a period of driving is necessary to bring the OBD II system to "ready" for inspection. A half-hour trip of mixed stop-and-go/high- way driving is typically needed to allow OBD II to reach readiness. Your Volvo retailer can provide you with more infor- mation on planning a trip. • Maintain your vehicle in accordance with your vehicle's maintenance schedule. How Do States Use OBD II for Emission Inspections? Many states connect a computer directly to a vehicle's OBD II system. The inspector can then read "faults." In some states, this type of inspection has replaced the tailpipe emission test. How Can My Vehicle Fail OBD II Emission Inspection? Your vehicle can fail OBD II emission inspec- tion for any of the following reasons. • If your Check Engine (MIL) light is lit, your vehicle may fail inspection. • If your vehicle's Check Engine light was lit, but went out without any action on your part, OBD II will still have a recorded fault. Your vehicle may pass or fail, depending on the inspection practices in your area. • If you had recent service that required dis- connecting the battery, OBD II diagnostic information may be incomplete and "not ready" for inspection. A vehicle that is not ready may fail inspection. How Can I Prepare for My Next OBD II Emission Inspection? • If your Check Engine (MIL) light is lit – or was lit but went out without service, have 209 09 Maintenance and servicing 09 Hood Opening the hood To open the hood: 1. Pull the lever located under the left side of the dash to release the hood lock. 2. Lift the hood slightly. 3. Press up the release control located under the front edge of the hood (at the center) up to the right, and lift the hood. WARNING Check that the hood locks engage properly when closed. 210 09 Maintenance and servicing Engine compartment 09 Cooling system expansion tank Power steering fluid reservoir (concealed behind the headlight) Dipstick – engine oil Relay/fuse box Air cleaner WARNING The cooling fan may start or continue to operate (for up to 6 minutes) after the engine has been switched off. Radiator Cooling fan Washer fluid reservoir Engine oil filler cap Brake/clutch fluid reservoir Battery 211 09 Maintenance and servicing 09 Engine oil Changing engine oil and oil filter See page 269 for oil specifications. Refer to the Warranty and Service Records Information booklet for information on the oil change inter- vals. Volvo recommends Castrol. NOTE • Volvo does not recommend the use of oil additives. • Synthetic oil is not used when the oil is changed at the normal maintenance intervals except at owner request and at additional charge. Please consult a trained and qualified Volvo service tech- nician. Checking and adding oil The oil level should be checked every time the vehicle is refueled. This is especially important during the period up to the first scheduled maintenance service • The car should be parked on a level surface when the oil is checked. • If the engine is warm, wait for at least 10–15 minutes after the engine has been switched off before checking the oil. 212 Location of dipstick and oil filler cap Checking the oil 1. Pull out the dipstick and wipe it with a lint- free rag. 2. Reinsert the dipstick, pull it out, and check the oil level. 3. Add oil if necessary. If the level is close to the MIN mark, add approximately 1 US quart (1 liter) of oil. 4. Run the engine until it reaches normal operating temperature. 5. Switch off the engine and wait for at least 10–15 minutes and recheck the oil level. If necessary, add oil until the level is near the MAX mark. CAUTION • Not checking the oil level regularly can result in serious engine damage if the oil level becomes too low. • Oil that is lower than the specified qual- ity can damage the engine. • Always add oil of the same type and viscosity as already used. • Never fill oil above the MAX mark. This could cause an increase in oil consump- tion. WARNING Do not allow oil to spill onto or come into contact with hot exhaust pipe surfaces NOTE Volvo uses different systems to indicate a low oil level or pressure. Some models have an oil pressure sensor, in which case a warning symbol (see page 57) is used to indicate low oil pressure. Other models have an oil level sensor, in which case the driver is alerted by the warning symbol in the cen- ter of the instrument panel and a text in the information display. Some models use both systems. Contact an authorized Volvo retailer for more information. 09 Maintenance and servicing Engine oil 09 213 09 Maintenance and servicing 09 Fluids Washer fluid Coolant Washer fluid reservoir The washer fluid reservoir is located in the engine compartment and holds approximately 6.8 US qts (6.5 liters). During cold weather, the reservoir should be filled with windshield washer solvent containing antifreeze. Coolant reservoir Normally, the coolant does not need to be changed. If the system must be drained, con- sult a trained and qualified Volvo service tech- nician. 214 CAUTION • If necessary, top up the cooling system with Volvo Genuine Coolant/Antifreeze only (a 50/50 mix of water and anti- freeze). • Different types of antifreeze/coolant may not be mixed. • If the cooling system is drained, it should be flushed with clean water or premixed anti-freeze before it is refilled with the correct mixture of water/anti- freeze. • The cooling system must always be kept filled to the correct level, and the level must be between the MIN and MAX marks. If it is not kept filled, there can be high local temperatures in the engine which could result in damage. Check coolant regularly! • Do not top up with water only. This reduces the rust-protective and anti- freeze qualities of the coolant and has a lower boiling point. It can also cause damage to the cooling system if it should freeze. • Do not use chlorinated tap water in the vehicles cooling system. WARNING Never remove the radiator cap while the engine is warm. Wait until the vehicle cools. If it is necessary to top off the coolant when the engine is warm, unscrew the expansion tank cap slowly so that the overpressure dissipates. Brake fluid Brake fluid reservoir The brake fluid should always be between the MIN and MAX marks on the side of the reser- voir. Check, without removing the cap, that there is sufficient fluid in the reservoir. Fluid type: DOT 4+ boiling point >536 °F 09 Maintenance and servicing Fluids 09 Power steering fluid The fluid level is checked at each service inter- val. Fluid type: Volvo power steering fluid or equiv- alent. Replace: No fluid change required. WARNING If a problem should occur in the power steering system or if the vehicle has no elec- trical current and must be towed, it is still possible to steer the vehicle. However, keep in mind that greater effort will be required to turn the steering wheel. (280 °C), P/N 9437433 Replace: The fluid should be replaced accord- ing to the intervals specified in the Warranty and Service Records Information booklet. When driving under extremely hard conditions (mountain driving, etc), it may be necessary to replace the fluid more often. Consult your Volvo retailer. Always entrust brake fluid changing to a trained and qualified Volvo serv- ice technician. WARNING • If the fluid level is below the MIN mark in the reservoir or if a brake-related message is shown in the information display: DO NOT DRIVE. Have the car towed to a trained and qualified Volvo service technician and have the brake system inspected. • Dot 4+ should never be mixed with any other type of brake fluid. 215 09 Maintenance and servicing 09 Wiper blades Replacing windshield wiper blades Liftgate wiper blade 1. Fold out the wiper arm. 2. Press the button on the wiper blade attach- ment and pull straight out (1), parallel with the wiper arm. 3. Press a new wiper blade (2) until it clicks into place. 4. Ensure the blade is securely attached (3). 5. Fold in the wiper arm. The wiper blades are different lengths. The blade on the driver's side is longer than the one on the passenger's side. 216 1. Fold out the wiper arm. 2. Remove the wiper blade by pulling it straight out from the wiper arm. 3. Press the new wiper blade securely into place. Fold in the wiper arm. Keeping the windshield/liftgate window and wiper blades clean helps improve visibility and prolongs the service life of the wiper blades. See page 198 for washing instructions. Battery maintenance Driving habits and conditions, climate, the number of starts, etc., all affect the service life and function of the battery. In order for your battery to perform satisfactorily, keep the fol- lowing in mind: Check the fluid level in each cell in the battery every 24 months or every 15,0001 miles (24,000 km), whichever is sooner. • Use a screw driver to open the caps or cover and a flashlight to inspect the level. • If necessary, add distilled water. The level should never be above the indicator. • The fluid level should be checked if the battery has been recharged. • After inspection, be sure the cap over each battery cell or the cover is securely in place. • Check that the battery cables are correctly connected and properly tightened. • Never disconnect the battery when the engine is running, or when the key is in the ignition. This could damage the vehicle's electrical system. • The battery should be disconnected from the vehicle when a battery charger is used directly on the battery. 1 More frequently in warm climates. 09 Maintenance and servicing • To help keep the battery in good condition, the vehicle should be driven for at least 15 minutes a week or connected to a charger with an automatic charging function. • If the battery is fully discharged a number of times, this may shorten its service life. Keeping the battery fully charged helps prolong its service life. • The service life of a battery is affected by factors such as driving conditions and cli- mate. Extreme cold may also further decrease the battery’s starting capacity. • Because the battery’s starting capacity decreases with time, it may be necessary to recharge it if the vehicle is not driven for an extended period of time or if the vehicle is usually only driven short distances. • WARNING PROPOSITION 65 WARNING! Battery posts, terminals, and related acces- sories contain lead and lead compounds, chemicals known to the state of California to cause cancer and reproductive harm. Wash hands after handling. Battery 09 Battery symbols Wear protection goggles See owner's manual for details Keep away from children Corrosive `` 217 09 Maintenance and servicing 09 Battery No smoking, no open flames, no sparks 7. Release the clamp holding the battery. 8. Lift out the battery. Explosion Installing a new battery 1. Put the battery in place in the engine com- partment. Install the battery's retaining clamp. 2. 3. Reinstall the front side of the battery box. 4. Connect the positive cable. 5. Connect the ground cable. 6. Reinstall the cover over the battery. Battery replacement Removing the battery 1. Switch off the ignition and remove the key. 2. Wait at least 5 minutes after switching off the ignition before disconnecting the bat- tery so that all information in the vehicle's electrical system can be stored in the con- trol modules. 3. Remove the cover over the battery. 4. Disconnect the battery negative (ground) cable. 5. Disconnect the positive cable. 6. Remove the front side of the battery box with a screwdriver. NOTE Used batteries should be properly disposed of at a recycling station or similar facility, or taken to your Volvo retailer. WARNING • Never expose the battery to open flame or electric spark. • Do not smoke near the battery. • Battery fluid contains sulfuric acid. Do not allow battery fluid to contact eyes, skin, fabrics or painted surfaces. If con- tact occurs, flush the affected area immediately with water. Obtain medical help immediately if eyes are affected. 218 Introduction Before replacing bulbs in your vehicle, please keep the following points in mind: NOTE Never touch the glass of bulbs with your fin- gers. Grease and oils from your fingers vaporize in the heat and will leave a deposit on the reflector, which will damage it. The optional Dual Xenon headlight bulbs contain trace amounts of mercury. These bulbs should always be disposed of by a trained and qualified Volvo service techni- cian. Certain bulbs should only be replaced by a trained and qualified Volvo service techni- cian: • Courtesylighting • Reading lights • Glove compartment lights • Turn signals and courtesy lights in the side door mirrors • High-mounted brake lights • Dual Xenon headlights, Brake lights 09 Maintenance and servicing Replacing bulbs 09 Removing the headlight housing WARNING • The engine should not be running when changing bulbs. • When changing in the headlight hous- ing, if the engine has been running just prior to replacing bulbs, please be aware that components in the engine compartment will be hot. light, turn signal, and side marker bulbs. To lift out the housing: 1. Remove the key from the ignition and turn the headlight switch to position 2. Open the hood. 3. Pull up the headlight housing's retaining pin. 4. Pull out the headlight housing. The entire headlight housing must be lifted out when replacing the high/low beam, parking 5. Disconnect the wiring connector by press- ing down the clip with your thumb while at the same time pulling the connector with your other hand. `` 219 09 Maintenance and servicing 09 Replacing bulbs 6. Lift out the headlight housing and place it on a soft surface to avoid scratching the lens. Low beam bulb CAUTION When disconnecting the connector, pull on the connector itself and not on the wiring. After the defective bulb has been replaced, reinsert the housing in the reverse order. Check that the retaining pin is correctly inserted. WARNING Dual Xenon headlights* – due to the high voltage used by these headlights, these bulbs should only be replaced by a trained and qualified Volvo service technician. Low beam bulb Cover with retaining clamps 1. Open the hood and remove the headlight housing (see page 219 for instructions). 2. Release the retaining clamps on the cover. 3. Release the bulb's retaining spring holding the bulb in place by pressing it first to the left and then moving it outward and down- ward. 4. Pull out the bulb. Installing a new bulb 1. Insert the new bulb. It can only be installed in one position. 2. Press the retaining spring inward and upward and slightly to the right until it snaps into place. 3. Press the wiring connector onto the bulb. 4. Put the plastic cover in place. 5. Press the retaining clamps back into place. 6. Reinstall the headlight housing (see page 219). 220 * Option/accessory, for more information, see Introduction. 09 Maintenance and servicing WARNING Dual Xenon headlights* – due to the high voltage used by these headlights, the Dual Xenon bulbs should only be replaced by a trained and qualified Volvo service techni- cian. 3. Driver's side headlight: Turn the bulb holder counterclockwise. Passenger's side headlight: Turn the bulb holder clockwise. 4. Pull out the bulb holder and replace the bulb. 5. Reinstall the bulb holder. It can only be installed in one position. 6. Reinstall the headlight housing (see page 219). High beam bulb Halogen high beam bulb 1. Open the hood. 2. Remove the headlight housing (see page 219). NOTE The halogen high beam bulb has a different socket on vehicles equipped with the optional Dual Xenon headlights. On these models, pull the bulb straight out. Replacing bulbs 09 Parking light bulb 1. Pull out the bulb holder with a pair of pliers. The bulb holder should not be pulled out by the wire. 2. Replace the bulb. 3. Press the bulb holder back into place. It can only be installed in one position. * Option/accessory, for more information, see Introduction. 221 `` 09 Maintenance and servicing 09 Replacing bulbs Turn signal Side marker light Front fog lights* 1. Turn the bulb holder counterclockwise and remove it. 2. Remove the bulb from the holder by press- 3. ing it in and twisting it counterclockwise. Insert a new bulb and reinstall the bulb holder in the headlight housing. 1. Turn the bulb holder counterclockwise, pull it out, and replace the bulb. 2. Reinstall the bulb holder. It can only be installed in one position. 1. Switch off all lights and turn the key to position 0. 2. Remove the panel around the fog light housing. 3. Unscrew both torx screws in the fog light housing and remove it. 222 * Option/accessory, for more information, see Introduction. 7. Reconnect the connector to the bulb. 4. Disconnect the connector from the bulb. 5. Turn the bulb counterclockwise and pull it 6. out. Install the new bulb in its seat and turn it clockwise. 09 Maintenance and servicing Replacing bulbs 09 8. Secure the fog light housing with the screws and press the panel back into place. Removing the taillight bulb holder 3. Disconnect the wiring connector from the affected bulb holder. 4. Press the catches together and pull out the bulb holder. 5. Replace the defective bulb. 6. Press the wiring connector back into posi- tion. 7. Press the bulb holder into place and rein- stall the cover. Location of taillight bulbs All bulbs in the taillight cluster can be replaced from the cargo area. To access the bulb hold- ers: 1. Switch off all lights and turn the key to position 0. 2. Remove the covers (A or B) in the left/right panels to access the bulb holders. Location of taillight bulbs 1 The wiring to the LED brake lights is permanently connected to the bulb holder. It should not be removed. Brake light (LED)1 Taillight/parking light/fog light (driver’s side only) Taillight/parking light Turn signal Back-up light Taillight/parking light NOTE If the message indicating a burned out bulb remains in the information display after the bulb has been replaced, consult a trained and qualified Volvo service technician. High-level brake light These bulbs should only be replaced by a trained and qualified Volvo service technician. `` 223 09 Maintenance and servicing 09 Replacing bulbs License plate lighting Rear grids Footwell lighting 1. Switch off all lights and turn the key to position 0. 2. Remove the screws with a screw driver. 3. Detach the lens (bulb housing) carefully. 4. Replace the defective bulb. 5. Reinstall the entire bulb housing and screw it into place. The grids are held in place by clips and can be pressed into position. They can only be instal- led one way. The footwell lighting is located under the dash- board on the driver's and passenger's sides. To replace a bulb: 1. Insert a screwdriver under the edge of the lens. Turn the screwdriver gently to detach the lens. 2. Remove the defective bulb. 3. 4. Press the lens back into place. Install a new bulb. 224 Cargo area lighting Cabin lighting in the cargo area Vanity mirror lighting 09 Maintenance and servicing Replacing bulbs 09 1. Insert a screwdriver and turn it gently to detach the bulb housing. 2. Remove the defective bulb. 3. 4. Press the bulb housing back into place. Install a new bulb. The rear cabin lighting consists of a light on the driver’s side of the cargo area 1. Insert a screwdriver and turn it carefully to release the lens. 2. Remove the connector from the bulb holder. 3. Replace the defective bulb. 4. Press the lens back into place. 1. Insert a screwdriver under the center of the lower edge of the mirror, turn it, and care- fully pry up the lugs at the edge. 2. Move the screwdriver under the edge on the left and right-hand sides (near the black rubber sections) and pry carefully to release the lower edge of the mirror. 3. Pry carefully and lift out the entire mirror and the cover. 4. Remove the defective bulb and replace it with a new one. 5. To reinstall the mirror, begin by pressing the three lugs at the upper edge of the mir- ror back into place. `` 225 09 Maintenance and servicing 09 Replacing bulbs 6. Press the three lower lugs back into place. 226 09 Maintenance and servicing Fuses 09 Replacing fuses There are relay/fuse boxes located in the engine compartment and the passenger com- partment. If an electrical component fails to function, this may be due to a blown fuse. The easiest way to see if a fuse is blown is to remove it. To do so: 1. Pull the fuse straight out. If a fuse is difficult to remove, special fuse removal tools are located on the inside of the fuse box cov- ers. 2. From the side, examine the curved metal 3. wire in the fuse to see if it is intact. If the wire is broken, insert a new fuse of the same color and amperage (written on the fuse). If fuses burn out repeatedly, have the electrical system inspected by a trained and qualified Volvo service technician. WARNING Never use metal objects or fuses with higher amperage than those stated on the follow- ing pages. Doing so could seriously damage or overload the vehicle's electrical system. `` 227 09 Maintenance and servicing 09 Fuses Fuse box in the engine compartment The fuse box in the engine compartment has positions for 36 fuses. • Fuses 1–18 are relays/circuit breakers and should only be removed or replaced by an authorized Volvo service technician. • Fuses 19–36 may be changed at any time when necessary. Several extra fuses and a fuse removal tool to assist in removing/replacing fuses can be found on the underside of the fuse box cover in the engine compartment. 228 Fuses in the engine compartment 09 Maintenance and servicing Fuses 09 1. 2. 3. 4. 5. 6. 7. 8. Coolant fan (radiator) Power steering Feed to passenger com- partment fuse box Feed to passenger com- partment fuse box Element, climate unit Not in use ABS pump ABS valves 50A 80A 60A 60A 80A 30A 20A 9. 10. 11. 12. 13. 14. 15. 16. Engine functions Climate system blower Headlight washers 30A 40A 20A Feed to heated rear window 30A Starter motor relay Trailer connector (acces- sory) 30A 40A Not in use Feed to audio system 30A 17. Windshield wipers 18. 19. 20. 21. 22. 23. Feed to passenger com- partment fuse box Not in use Horn Not in use Not in use Engine control module (ECM)/transmission control module (TCM) 30A 40A 15A 10A `` 229 09 Maintenance and servicing 09 Fuses 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. Not in use Not in use Ignition switch A/C compressor Not in use Front fog lights* Not in use Not in use Fuel injectors Heated oxygen sensor, vac- uum pump Ignition coils, climate unit pressure sensor Engine sensor valves, A/C relay, relay coil, PTC ele- ment oil trap, canister, mass air meter 36. Engine control module (ECM), throttle sensor 15A 10A 15A 10A 20A 10A 15A 10A 230 * Option/accessory, for more information, see Introduction. 09 Maintenance and servicing Fuses 09 Fuse box in the passenger compartment The fuse box in the passenger compartment is located under the glove compartment. To access the fuses: 1. Remove the upholstery covering the fuse box by first pressing in the center pins in the mounting clips approximately 0.5 in (1 cm) with a small screwdriver and then pulling the pins out. 2. Turn both retaining screws (2) counter- clockwise until they release. 3. Fold down the fuse box (3) half way. Pull it toward the seat until it stops. Fold it down completely. The fuse box can be unhooked completely. 4. Replace the blown fuse. 5. Close the fuse box in reverse order. 6. Pull the center pins fully out of the mount- ing clips, secure the upholstery with the mounting clips and press the pins into the mounting clips again. The mounting clips then expand, holding the upholstery in position. `` 231 09 Maintenance and servicing 09 Fuses Fuses in the passenger compartment 43. 44. 45. 46. Fuse 37-42, not in use Audio system, Blue- tooth,Volvo Navigation sys- tem* Supplemental Restrain Sys- tem (SRS), engine control module 12-volt socket in rear seat Lighting – glove compart- ment, instrument panel, and footwells 15A 10A 15A 5A 47. 48. 49. 50. 51. 52. Interior lighting Rear liftgate wiper/washer Supplemental Restrain Sys- tem (SRS), Occupant Weight Sensor (OWS) Not in use Fuel filter relay Transmission control mod- ule (TCM), ABS 53. Power steering 5A 15A 10A 10A 5A 10A 232 * Option/accessory, for more information, see Introduction. 54. 55. 56. Park assist*, Dual Xenon headlights* 10A Not in use Volvo Navigation System remote key module, alarm siren control module 57. On-board diagnostic socket, brake light switch 58. Right high beam, auxiliary lights relay 59. Left high beam 10A 15A 7.5A 7.5A 09 Maintenance and servicing Fuses 09 76. 77. 78. 79. 80. 81. 82. 83. 84. 85. 86. Not in use Not in use Not in use Back-up lights Not in use Not in use Power window – front pas- senger's side door Power window and door lock – front driver's side door Power passenger's seat Power driver's seat Interior lighting relay, cargo area light, power seats 5A 20A 25A 25A 25A 25A 5A 60. 61. Heated driver's seat* Heated passenger's seat* 62. Moonroof* 63. 64. 65. 66. 67. 68. 69. 70. 71. 72. Not in use Audio system, Volvo Navi- gation system* Audio system Audio system control mod- ule (ICM), climate system Not in use Cruise control Climate system, rain sen- sor*, BLIS button* Not in use Not in use Not in use 73. Moonroof, front ceiling lighting, auto-dim mirror*, seat belt reminder 74. 75. Fuel pump relay Not in use 15A 15A 20A 5A 5A 10A 5A 5A 5A 15A * Option/accessory, for more information, see Introduction. 233 Audio functions..................................................................................... 236 Radio functions..................................................................................... 241 CD player/CD changer.......................................................................... 249 Audio menu........................................................................................... 253 Bluetooth® hands-free connection....................................................... 254 234 AUDIO 10 10 Audio Audio functions Audio system controls 10 VOLUME dial AM/FM – select a radio band MODE – select a sound source TUNING dial SOUND button Auxiliary connector AUX port USB connector* Selecting a sound source ± Press AM/FM (2) repeatedly to toggle between FM1, FM2, and AM. ± Press MODE (3) repeatedly to toggle between the CD player and the optional external sound source AUX, USB or the optional Sirius satellite radio. The currently selected sound source will be shown in the display. 236 * Option/accessory, for more information, see Introduction. AUX The AUX (auxiliary) port, located under the cen- ter armrest, can be used to connect for exam- ple, an MP3 player. If the player is being charged through a 12-volt socket while it is connect to the AUX port, sound quality may be impaired. The volume of the external sound source AUX may be different from the volume of the internal sound sources such as the CD player or the radio. If the external sound source's volume is too high, the quality of the sound may be impaired. This can be prevented by adjusting the external sound source's input volume. 1. While playing the radio or a CD, lower the audio volume to about one-quarter. 2. Switch to AUX mode on the audio system by pressing the MODE button. 3. Connect the headphone output from your music player to the AUX input using a cable with a stereo 3.5 mm miniplug at both ends. 4. Set your music player's headphone vol- ume to three-quarters using the player's volume controls. 5. Press MENU on the audio system, and navigate to AUX Volume or AUX Input Volume. 6. Turn the volume knob to raise or lower the AUX Input Volume until you hear music at a comfortable level. If there is distortion, lower your music play- er's headphone volume until the distortion goes away. 7. 8. Finally, exit the menu and adjust the audio volume to a comfortable level. Volume Use the volume dial (1) or the buttons in the steering wheel keypad to adjust the volume level. The volume level is also adjusted auto- matically according to the vehicle's speed, see page 239 for more information on this func- tion. 10 Audio Audio functions Steering wheel keypad USB/iPod(cid:159)(cid:159) connector* 10 Steering wheel keypad The four buttons on the steering wheel keypad can be used to control the audio system. The steering wheel keypad can be used to adjust volume, shift between preset stations and change CD tracks. Press one of the two left- hand buttons briefly to change to the next/pre- vious preset radio station, or to go to the next/ previous track on a CD. Press and hold down these buttons to search within a track on a CD. Daytime/twilight display In daylight the information is displayed against a light background. In darkness it is displayed against a dark background. An auxiliary device, such as an iPod(cid:159), MP3 player or a USB flash drive can be connected to the audio system via the connector in the center console storage compartment. A stand- ard cable from an iPod(cid:159) or MP3 player can be routed under the cover to the AUX connector in the storage compartment. A sound source must be chosen, depending on the device that has been connected: 1. Use MODE to select iPod or USB. The text CONNECT DEVICE will be displayed. 2. Connect the device to the connector in the center console storage compartment (see the illustration). * Option/accessory, for more information, see Introduction. 237 `` 10 Audio Audio functions The text LOADING will be displayed while the system loads the files (folder structure) on the device. This may take a short time. When information about the files (the folder structure) on the device has been loaded, the resulting list includes information on the artist, genre and song title. To navigate in the folder structure, press ENTER and scroll up and down the folders using the arrow buttons (on the audio system control panel or on the steering wheel keypad). Press the right arrow button to select a folder. Press the left arrow button to go up a level in the folder structure. Press ENTER to go down a level in the folder structure. Tracks can be selected in two ways: ± Turn the Tuning knob (no. 4 in the illustra- tion on page 241) clockwise or counter- clockwise. ± Use the right or left arrow keys on the nav- igation control (no. 5 in the illustration on page 241) to select the desired track. The arrow keys on the steering wheel keypad can also be used in the same way. 10 238 NOTE The system supports playback of files in the most common versions of formats such as mp3, wma, and wav. However, there may be versions of these formats that the system does not support. The system also supports a number of iPod(cid:159) models produced in 2005 or later. iPod(cid:159) Shuffle is not supported. USB flash drive To simplify the use of a USB flash drive, it is advisable to only store music files on the drive. It will take considerably longer for the system to index the files on the drive if it contains any- thing other than compatible music files. NOTE The system supports removable media that uses the USB 2.0 standard and the FAT32 file system and can index up to 500 folders and a maximum of 64,000 files. The device must have at least 256 Mb of memory. MP3 player Many MP3 players have a file indexing system that is not supported by the vehicle's audio system. In order to use an MP3 player, the sys- tem must be set to USB Removable device/ Mass Storage Device. iPod(cid:159) An iPod(cid:159) receives current and its battery is charged through the connecting cord. How- ever, if the iPod's battery is completely drained, it should be recharged before the iPod(cid:159) is connected to the audio system. NOTE When an iPod(cid:159) is used as a sound source, the vehicle's audio system has a menu structure similar to the one in the iPod(cid:159). See the iPod's manual for detailed information. For further information, refer to the accessory manual USB/iPod(cid:159) Music Interface. Sound settings Optimal sound reproduction The audio system is calibrated for optimal sound reproduction through the use of digital signal processing. This calibration takes into account the speakers, amplifier, cabin acous- tics, the seating position of the listener, etc., for each combination of vehicle and audio system. There is also dynamic calibration that takes into account the setting of the volume control, radio reception, and the vehicle's speed. The sound settings described in this manual, such as BASS, TREBLE, and EQUALIZER are only intended to enable the user to adapt sound reproduction to his/her personal preferences. 1. Press SOUND (5). Press this button repeatedly until you come to the setting that you wish to change. 2. Turn the TUNING dial (4) to make the desired setting. The following settings can be made: BASS–set the bass level TREBLE–set the treble level BALANCE–set the left/right sound balance FADER–set the front/rear sound balance CENTER–make settings for the center speaker SURROUND–make settings for surround sound Surround sound Surround sound settings are used to balance sound levels throughout the vehicle. Surround settings for the var- ious sound sources are made sepa- rately. NOTE • Dolby Surround Pro Logic II is only available on the Premium Sound sys- tem. • When listening to FM radio stations, Dolby Surround Pro Logic II functions best in areas with strong reception. If reception is weak, selecting 2 or 3- channel stereo may provide better sound quality. The Dolby symbol will be appear in the display when Dolby Pro Logic II is activated. There are three alternative settings: • Pro Logic II • 3-channel • Off (normal 2-channel stereo) Activating/deactivating Surround sound 1. Press MENU followed by ENTER. 2. Select AUDIO SETTINGS in the menu and press ENTER. 3. Select Surround FM/AM/CD/AUX and press ENTER. 4. Select Pro logic II, 3-channel stereo or Off and press ENTER. 10 Audio Audio functions Equalizer Front/Rear This function is used to fine-tune the sound level for different frequencies separately. 10

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2010 Volvo C30 Owners Manual