2013 Toyota Yaris Owners Manual

211

3-5. Other interior features

■The outside temperature is displayed when

The engine switch is in the “ON” position.

■Display

In the following situations, the correct outside temperature may not be dis- played, or the display may take longer than normal to change: ●When the vehicle is stopped, or moving at low speeds (less than 16 mph

[25 km/h])

●When the outside temperature has changed suddenly (at the entrance/

exit of a garage, tunnel, etc.)

■When “− −” or “E” is displayed

The system may be malfunctioning. Take your vehicle to your Toyota dealer.

212

3-5. Other interior features Power outlet

The power outlet can be used for 12 V accessories that run on less than 10 A.

■The power outlet can be used when

The engine switch is in the “ACC” or “ON” position.

NOTICE

■To avoid damaging the power outlet

Close the power outlet lid when the power outlet is not in use. Foreign objects or liquids that enter the power outlet may cause a short cir- cuit.

■To prevent blown fuse

Do not use an accessory that uses more than 12 V 10 A.

■To prevent battery discharge

Do not use the power outlet longer than necessary when the engine is not running.

213

3-5. Other interior features Assist grips

An assist grip installed on the ceiling can be used to support your body while sitting on the seat.

CAUTION

■Assist grip

Do not use the assist grip when getting in or out of the vehicle or rising from your seat.

NOTICE

■To prevent damage to the assist grip

Do not hang any heavy object or put a heavy load on the assist grip.

214

3-5. Other interior features Floor mat

Use only floor mats designed specifically for vehicles of the same model and model year as your vehicle. Fix them securely in place onto the carpet.

the

Insert retaining hooks (clips) into the floor mat eye- lets.

Turn the upper knob of each retaining hook (clip) to secure the floor mats in place. *: Always align the

marks.

The shape of the retaining hooks (clips) may differ from that shown in the illustration.

215

3-5. Other interior features

CAUTION

Observe the following precautions. Failure to do so may cause the driver’s floor mat to slip, possibly interfering with the pedals while driving. An unexpectedly high speed may result or it may become difficult to stop the vehicle, leading to a serious accident. ■When installing the driver’s floor mat

●Do not use floor mats designed for other models or different model year

vehicles, even if they are Toyota Genuine floor mats.

●Only use floor mats designed for the driver’s seat. ●Always install the floor mat securely using the retaining hooks (clips) pro-

vided.

●Do not use two or more floor mats on top of each other. ●Do not place the floor mat bottom-side up or upside-down.

■Before driving

●Check that the floor mat is securely fixed in the correct place with all the provided retaining hooks (clips). Be especially careful to perform this check after cleaning the floor.

●With the engine stopped and the shift lever in P (vehicles with an automatic transmission) or N (vehicles with a manual fully depress each pedal to the floor to make sure it does not interfere with the floor mat.

transmission),

216

3-5. Other interior features Luggage compartment features

■ Deck board

Removing the deck board

Lift up the deck board and pull it towards you to remove it.

Securing the deck board

Lift up the deck board.

217

3-5. Other interior features

Remove the hook on the back- side of the deck board. Attach the hook to the upper edge of the back door opening as shown.

■Removing the luggage cover

The luggage cover can be removed by the following procedure:

Unhook the cords. Return the luggage cover to horizontal position.

Lift the luggage cover and pull it forward.

218

3-5. Other interior features

CAUTION

■When operating the deck board

Do not place anything on the deck board when operating the board. Other- wise, your fingers may be caught or an accident may result causing injuries.

219

3-5. Other interior features

220

4-1. Maintenance and care Cleaning and protecting the vehicle exterior

Perform the following to protect the vehicle and maintain it in prime condition:

● Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust.

● Wash the vehicle body using a sponge or soft cloth, such as a

chamois.

● For hard-to-remove marks, use car wash soap and rinse thor-

oughly with water.

● Wipe away any water. ● Wax the vehicle when the waterproof coating deteriorates.

If water does not bead on a clean surface, apply wax when the vehi- cle body is cool.

■Automatic car washes

●Fold the mirrors and remove the antenna before washing the vehicle. Start washing from the front of the vehicle. Make sure to re-install the antenna and extend the mirrors before driving.

●Brushes used in automatic car washes may scratch the vehicle surface

and harm your vehicle’s paint.

●For vehicles with the rear spoiler, in certain automatic car washes, the rear spoiler may interfere with machine operation. This may prevent the vehicle from being cleaned properly or result in damage to the rear spoiler.

■High pressure car washes

●Do not allow the nozzles of the car wash to come within close proximity

of the window and door borders, and high mounted stoplight.

●Before using the car wash, check that the fuel filler door on your vehicle

is closed properly.

222

4-1. Maintenance and care

■Aluminum wheels (if equipped)

●Remove any dirt immediately by using a neutral detergent. Do not use hard brushes or abrasive cleaners. Do not use strong or harsh chemical cleaners. Use the same mild detergent and wax as used on the paint.

●Do not use detergent on the wheels when they are hot, for example after

driving for long distance in the hot weather.

●Wash detergent from the wheels immediately after use. ●To preserve the wheels’ luster, do not allow hot water, such as from

steam cleaning, to contact them directly.

■Bumpers

Do not scrub with abrasive cleaners.

CAUTION

■When washing the vehicle

Do not apply water to the inside of the engine compartment. Doing so may cause the electrical components etc. to catch fire.

■Precautions regarding the exhaust pipe

Exhaust gasses cause the exhaust pipe to become quite hot. When washing the vehicle, be careful not to touch the pipe until it has cooled sufficiently, as touching a hot exhaust pipe can cause burns.

223

4-1. Maintenance and care

NOTICE

■To prevent paint deterioration and corrosion on the body and compo-

nents (aluminum wheels etc.) ●Wash the vehicle immediately in the following cases:

• After driving near the sea coast • After driving on salted roads • If coal tar or tree sap is present on the paint surface • If dead insects, insect droppings or bird droppings are present on the

paint surface

• After driving in an area contaminated with soot, oily smoke, mine dust,

iron powder or chemical substances

• If the vehicle becomes heavily soiled with dust or mud • If liquids such as benzene and gasoline are spilled on the paint surface

●If the paint is chipped or scratched, have it repaired immediately. ●To prevent the wheels from corroding, remove any dirt and store in a place

with low humidity when storing the wheels.

■Cleaning the exterior lights

●Wash carefully. Do not use organic substances or scrub with a hard brush.

This may damage the surfaces of the lights.

●Do not apply wax to the surfaces of the lights.

Wax may cause damage to the lenses.

■Antenna installation and removal precautions

●Before driving, ensure that the antenna is installed. ●When the antenna is removed, such as before entering an automatic car wash, make sure to store it in a suitable place so as not to lose it. Also, before driving, make sure to reinstall the antenna in its original position.

■To prevent damage to the antenna

Remove the antenna in the following situations: ●When the antenna will touch the ceiling of a garage or other such places ●When a car cover is to be used to cover the vehicle

224

4-1. Maintenance and care Cleaning and protecting the vehicle interior

The following procedures will help protect your vehicle’s interior and keep it in top condition: ■ Protecting the vehicle interior

Remove dirt and dust using a vacuum cleaner. Wipe dirty sur- faces with a cloth dampened with lukewarm water.

■ Cleaning the leather areas

● Remove dirt and dust using a vacuum cleaner. ● Wipe off any excess dirt and dust with a soft cloth dampened

with diluted detergent. Use a diluted water solution of approximately 5% neutral wool deter- gent.

● Wring out any excess water from the cloth and thoroughly

wipe off all remaining traces of detergent.

● Wipe the surface with a dry, soft cloth to remove any remain- ing moisture. Allow the leather to dry in a shaded and venti- lated area.

■ Cleaning the synthetic leather areas

● Remove loose dirt using a vacuum cleaner. ● Apply a mild soap solution to the synthetic leather using a

sponge or soft cloth.

● Allow the solution to soak in for a few minutes. Remove the

dirt and wipe off the solution with a clean, damp cloth.

225

4-1. Maintenance and care

■Caring for leather areas

Toyota recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle’s interior.

■Shampooing the carpets

There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam. Rub in overlapping circles. Do not use water. Wipe dirty surfaces and let them dry. Excellent results are obtained by keeping the carpet as dry as possible.

■Seat belts

Clean with mild soap and lukewarm water using a cloth or sponge. Also check the belts periodically for excessive wear, fraying or cuts.

CAUTION

■Water in the vehicle

●Do not splash or spill liquid in the vehicle.

Doing so may cause electrical components etc. to malfunction or catch fire.

●Do not get any of the SRS components or wiring in the vehicle interior wet.

(→P. 82) An electrical malfunction may cause the airbags to deploy or not function properly, resulting in death or serious injury.

■Cleaning the interior (especially instrument panel)

Do not use polish wax or polish cleaner. The instrument panel may reflect off the windshield, obstructing the driver’s view and leading to an accident, resulting in death or serious injury.

226

4-1. Maintenance and care

NOTICE

■Cleaning detergents

●Do not use the following types of detergent, as they may discolor the vehi-

cle interior or cause streaks or damage to painted surfaces: • Non-seat portions: Organic substances such as benzene or gasoline,

alkaline or acidic solutions, dye, and bleach

• Seats: Alkaline or acidic solutions, such as thinner, benzene, and alco-

hol

●Do not use polish wax or polish cleaner. The instrument panel’s or other

interior part’s painted surface may be damaged.

■Preventing damage to leather surfaces

Observe the following precautions to avoid damage to and deterioration of leather surfaces: ●Remove any dust or dirt from leather surfaces immediately. ●Do not expose the vehicle to direct sunlight for extended periods of time.

Park the vehicle in the shade, especially during summer.

●Do not place items made of vinyl, plastic, or containing wax on the uphol- stery, as they may stick to the leather surface if the vehicle interior heats up significantly.

■Water on the floor

Do not wash the vehicle floor with water. Vehicle systems such as the audio system may be damaged if water comes into contact with electrical components such as the audio system above or under the floor of the vehicle. Water may also cause the body to rust.

■Cleaning the inside of the rear window

●Do not use glass cleaner to clean the rear window, as this may cause damage to the rear window defogger heater wires. Use a cloth dampened with lukewarm water to gently wipe the window clean. Wipe the window in strokes running parallel to the heater wires.

●Be careful not to scratch or damage the heater wires.

227

4-2. Maintenance Maintenance requirements

To ensure safe and economical driving, day-to-day care and regular maintenance are essential. It is the owner’s responsibility to perform regular checks. Toyota recommends performing the following main- tenance: ■ General maintenance

General maintenance should be performed on a daily basis. This can be done by yourself or by a Toyota dealer.

■ Scheduled maintenance

Scheduled maintenance should be performed at specified inter- vals according to the maintenance schedule. For details about maintenance items and schedules, refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.

■ Do-it-yourself maintenance

You can perform some maintenance procedures by yourself. Please be aware that do-it-yourself maintenance may affect war- ranty coverage. The use of Toyota Repair Manuals is recommended. For details about warranty coverage, see the separate “Owner’s Warranty Information Booklet” or “Owner’s Manual Supplement”.

■Repair and replacement

It is recommended that genuine Toyota parts be used for repairs to ensure performance of each system. If non-Toyota parts are used in replacement or if a repair shop other than a Toyota dealer performs repairs, confirm the war- ranty coverage.

228

4-2. Maintenance

■Reset the maintenance data (except Canada)

After the required maintenance is performed according to the maintenance schedule, please reset the maintenance data. To reset the data, follow the procedures described below:

Switch the display to the trip meter “A” when the engine is running. (→P. 133) Turn the engine switch to the “LOCK” position. While pressing the display change button (→P. 133), turn the engine switch to the “ON” position (do not start the engine because reset mode will be canceled). Continue to press and hold the button until the trip meter displays “000000”.

■Allow inspection and repairs to be performed by a Toyota dealer

●Toyota technicians are well-trained specialists and are kept up to date with the latest service information. They are well informed about the operations of all systems on your vehicle.

●Keep a copy of the repair order. It proves that the maintenance that has been performed is under warranty coverage. If any problem should arise while your vehicle is under warranty, your Toyota dealer will promptly take care of it.

CAUTION

■If your vehicle is not properly maintained

Improper maintenance could result in serious damage to the vehicle and possible serious injury or death.

■Handling of the battery

●Engine exhaust, some of its constituents, and a wide variety of automobile components contain or emit chemicals known to the State of California to cause cancer and birth defects and other reproductive harm. Work in a well ventilated area.

●Oils, fuels and fluids contained in vehicles as well as waste produced by component wear contain or emit chemicals known to the State of Califor- nia to cause cancer and birth defects or other reproductive harm. Avoid exposure and wash any affected area immediately.

●Battery posts, terminals and related accessories contain lead and lead compounds which are known to cause brain damage. Wash your hands after handling. (→P. 250)

229

4-2. Maintenance General maintenance

Listed below are the general maintenance items that should be performed at the intervals specified in the “Owner’s Warranty Information Booklet” or “Owner’s Manual Supplement/Scheduled Maintenance Guide”. It is recommended that any problem you notice should be brought to the attention of your Toyota dealer or qualified service shop for advice.

Engine compartment

Items

Check points

(→P. 247)

Check the battery fluid and connections. (→P. 250) Is the brake fluid at the correct level? (→P. 249) Is the engine coolant at the correct level? Is the engine oil at the correct level? There should not be any fumes or strange sounds. The radiator and condenser should be free from foreign objects. (→P. 248) Is there sufficient washer fluid? (→P. 253)

(→P. 244)

Battery

Brake fluid

Engine coolant

Engine oil

Exhaust system

Radiator/condenser

Washer fluid

230

4-2. Maintenance

Vehicle interior

Items

Check points

Accelerator pedal

Automatic transmission “Park” mechanism

Brake pedal

Brakes

Clutch pedal

Head restraints

• The accelerator pedal should move smoothly (without uneven pedal effort or catching). • When parked on a slope and the shift lever is in P, is the vehicle securely stopped? • Does the brake pedal move smoothly? • Does the brake pedal have appro- priate clearance from the floor? (→P. 350) • Does the brake pedal have the correct amount of free play? (→P. 350) • The vehicle should not pull to one side when the brakes are applied. • The brakes should work effec- tively. • The brake pedal should not feel spongy. • The brake pedal should not get too close to the floor when the brakes are applied. • Does the clutch pedal move smoothly? • Does the clutch pedal have appropriate clearance from the floor? • Does the clutch pedal have the correct amount of free play? (→P. 349) • Do the head restraints move smoothly and lock securely?

231

4-2. Maintenance

Items

Check points

Indicators/buzzers

Lights

Parking brake

Seat belts

Seats

Steering wheel

• Do the indicators and buzzers function properly? • Do all the lights come on? • Does the parking brake lever move smoothly? • When parked on a slope and the parking brake is on, is the vehicle securely stopped? • Do the seat belts operate smoothly? • The seat belts should not be dam- aged. • Do the seat controls operate properly? • Does the steering wheel rotate smoothly? • Does the steering wheel have the correct amount of free play? • There should not be any strange sounds coming from the steering wheel.

232

4-2. Maintenance

Vehicle exterior

Items

Check points

Doors

Engine hood

Fluid leaks

Tire

• Do the doors operate smoothly? • Does the engine hood lock sys- tem work properly? • There should not be any signs of fluid leakage after the vehicle has been parked. • Is the tire inflation pressure cor- rect? • The tires should not be dam- aged or excessively worn. • Have the tires been rotated according to the maintenance schedule? • The wheel nuts should not be loose.

CAUTION

■If the engine is running

Turn the engine off and ensure that there is adequate ventilation before per- forming maintenance checks.

233

4-2. Maintenance Emission inspection and maintenance (I/M) programs

Some states have vehicle emission inspection programs which include OBD (On Board Diagnostics) checks. The OBD system moni- tors the operation of the emission control system. ■ If the malfunction indicator lamp comes on

The OBD system determines that a problem exists somewhere in the emission control system. Your vehicle may not pass the I/ M test and may need to be repaired. Contact your Toyota dealer to service the vehicle.

■ Your vehicle may not pass the I/M test in the following situa-

tions: ● When the battery is disconnected or discharged

Readiness codes that are set during ordinary driving are erased. Also, depending on your driving habits, the readiness codes may not be completely set.

● When the fuel tank cap is loose

The malfunction indicator lamp comes on indicating a tempo- rary malfunction and your vehicle may not pass the I/M test.

■ When the malfunction indicator lamp still remains on after

several driving trips The error code in the OBD system will not be cleared unless the vehicle is driven 40 or more times.

■ If your vehicle does not pass the I/M test

Contact your Toyota dealer to prepare the vehicle for re-testing.

234

4-3. Do-it-yourself maintenance Do-it-yourself service precautions

If you perform maintenance by yourself, be sure to follow the correct procedures as given in these sections.

Items

Parts and tools

Battery condition

(→P. 250)

Brake fluid level

(→P. 249)

Engine coolant level

(→P. 247)

Engine oil level

(→P. 244)

• Warm water • Baking soda • Grease • Conventional wrench (for terminal clamp bolts) • Distilled water • FMVSS No.116 DOT 3 or SAE J1703 brake fluid • Rag or paper towel • Funnel (used only for adding brake fluid) • “Toyota Super Long Life Coolant” or similar high quality ethylene glycol-based non-silicate, non-amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology. Except Canada: “Toyota Super Long Life Coolant” is pre-mixed with 50% coolant and 50% deionized water. Canada: “Toyota Super Long Life Coolant” is pre-mixed with 55% coolant and 45% deionized water. • Funnel (used only for adding engine coolant) • “Toyota Genuine Motor Oil” or equivalent • Rag or paper towel • Funnel (used only for adding engine oil)

235

4-3. Do-it-yourself maintenance

Items

Parts and tools

Fuses

(→P. 275)

Light bulbs

(→P. 287)

Radiator and condenser

(→P. 248)

Tire inflation pressure (→P. 262)

Washer fluid

(→P. 253)

• Fuse with same amperage rating as original • Bulb with same number and watt- age rating as original • Phillips-head screwdriver • Flathead screwdriver • Wrench

⎯

• Tire pressure gauge • Compressed air source • Water or washer fluid containing antifreeze (for winter use) • Funnel (used only for adding water or washer fluid)

CAUTION

The engine compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energized. To avoid death or serious injury, observe the following precautions: ■When working on the engine compartment:

●Keep hands, clothing and tools away from the moving fan and engine

drive belt.

●Be careful not to touch the engine, radiator, exhaust manifold, etc. right

after driving as they may be hot. Oil and other fluids may also be hot.

●Do not leave anything that may burn easily, such as paper and rags, in the

engine compartment.

●Do not smoke, cause sparks or expose an open flame to fuel or the bat-

tery. Fuel and battery fumes are flammable.

●Be extremely cautious when working on the battery. It contains poisonous

and corrosive sulfuric acid.

236

4-3. Do-it-yourself maintenance

CAUTION

■When working near the electric cooling fan or radiator grille

Be sure the engine switch is off. With the engine switch on, the electric cooling fan may automatically start to run if the air conditioning is on and/or the coolant temperature is high. (→P. 248)

■Safety glasses

Wear safety glasses to prevent flying or falling material, fluid spray, etc. from getting in your eyes.

NOTICE

■If you remove the air cleaner filter

Driving with the air cleaner filter removed may cause excessive engine wear due to dirt in the air.

237

4-3. Do-it-yourself maintenance Hood

Release the lock from the inside of the vehicle to open the hood.

Pull the hood lock release lever.

The hood will pop up slightly.

Pull up the auxiliary catch lever and lift the hood.

Hold the hood open by insert- ing the supporting rod into the slot.

238

4-3. Do-it-yourself maintenance

CAUTION

■Pre-driving check

Check that the hood is fully closed and locked. If the hood is not locked properly, it may open while the vehicle is in motion and cause an accident, which may result in death or serious injury.

■After installing the support rod into the slot

Make sure the rod supports the hood securely from falling down on to your head or body.

NOTICE

■When closing the hood

Be sure to return the support rod to its clip before closing the hood. Closing the hood with the support rod up could cause the hood to bend.

239

4-3. Do-it-yourself maintenance Positioning a floor jack

When raising your vehicle with a floor jack, position the jack cor- rectly. Improper placement may damage your vehicle or cause injury. Front

Rear

240

4-3. Do-it-yourself maintenance

CAUTION

■When raising your vehicle

Make sure to observe the following precautions to reduce the possibility of death or serious injury:

●Lift up the vehicle using a floor jack such as the one shown in the illustra- tion.

●When using a floor jack, follow the instructions of the manual provided with

the jack.

●Do not use the jack that was supplied with your vehicle. ●Do not put any part of your body underneath the vehicle when it is sup-

ported only by the floor jack.

●Always use floor jack and/or automotive jack stands on a solid, flat, level

surface.

●Do not start the engine while the vehicle is supported by the floor jack. ●Stop the vehicle on level, firm ground, firmly set the parking brake and shift the shift lever to P (vehicles with an automatic transmission) or R (vehicles with a manual transmission).

●Make sure to set the floor jack properly at the jack point.

Raising the vehicle with an improperly positioned floor jack will damage the vehicle and may cause the vehicle to fall off the floor jack.

Suspension

Front

●Do not jack the vehicle at the suspen- sion. The suspension may be dam- aged.

241

4-3. Do-it-yourself maintenance

CAUTION

●Do not raise the vehicle while someone is in the vehicle. ●When raising the vehicle, do not place any object on top of or underneath

the floor jack.

242

4-3. Do-it-yourself maintenance Engine compartment

Fuse boxes Engine oil filler cap

(→P. 275)

(→P. 245) (→P. 250)

Battery Brake fluid reservoir

Radiator

(→P. 249) (→P. 248)

(→P. 248)

Condenser Electric cooling fan Engine coolant reservoir

(→P. 247)

Engine oil level dipstick

(→P. 244) Washer fluid tank (→P. 253)

243

4-3. Do-it-yourself maintenance

Engine oil

With the engine at operating temperature and turned off, check the oil level on the dipstick. ■ Checking the engine oil

Park the vehicle on level ground. After warming up the engine and turning it off, wait more than 5 minutes for the oil to drain back into the bottom of the engine.

Holding a rag under the end, pull the dipstick out.

Wipe the dipstick clean. Reinsert the dipstick fully. Holding a rag under the end, pull the dipstick out and check the oil level. Wipe the dipstick and reinsert it fully. Low Full

Measuring side

244

■ Adding engine oil

4-3. Do-it-yourself maintenance

If the oil level is below or near the low level mark, add engine oil of the same type as that already in the engine.

Make sure to check the oil type and prepare the items needed before adding oil.

Engine oil selection →P. 346
Oil quantity (Low → Full) Item

Clean funnel

1.6 qt. (1.5 L, 1.3 lmp.qt.)

Remove the oil filler cap by turning it counterclockwise. Add engine oil slowly, checking the dipstick. Install the oil filler cap by turning it clockwise.

■Engine oil consumption

A certain amount of engine oil will be consumed while driving. In the follow- ing situations, oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals. ●When the engine is new, for example directly after purchasing the vehicle

or after replacing the engine

●If low quality oil or oil of an inappropriate viscosity is used ●When driving at high engine speeds or with a heavy load, when towing,

or when driving while accelerating or decelerating frequently

●When leaving the engine idling for a long time, or when driving frequently

thorough heavy traffic

245

4-3. Do-it-yourself maintenance

CAUTION

■Used engine oil

●Used engine oil contains potentially harmful contaminants which may cause skin disorders such as inflammation and skin cancer, so care should be taken to avoid prolonged and repeated contact. To remove used engine oil from your skin, wash thoroughly with soap and water.

●Dispose of used oil and filters only in a safe and acceptable manner. Do not dispose of used oil and filters in household trash, in sewers or onto the ground. Call your Toyota dealer, service station or auto parts store for information concerning recycling or disposal.

●Do not leave used engine oil within the reach of children.

NOTICE

■To prevent serious engine damage Check the oil level on a regular basis.

■When replacing the engine oil

●Be careful not to spill engine oil on the vehicle components. ●Avoid overfilling, or the engine could be damaged. ●Check the oil level on the dipstick every time you refill the vehicle. ●Be sure the engine oil filler cap is properly tightened.

246

4-3. Do-it-yourself maintenance

Engine coolant

The coolant level is satisfactory if it is between the “FULL” and “LOW” lines on the reservoir when the engine is cold.

Reservoir cap “FULL” line “LOW” line If the level is on or below the “LOW” line, add coolant up to the “FULL” line.

■Coolant selection

Only use “Toyota Super Long Life Coolant” or a similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology. Except Canada:“Toyota Super Long Life Coolant” is a mixture of 50% cool- ant and 50% deionized water. (Minimum temperature: -31°F [-35°C])

Canada:“Toyota Super Long Life Coolant” is a mixture of 55% coolant and

45% deionized water. (Minimum temperature: -44°F [-42°C])

For more details about engine coolant, contact your Toyota dealer.

■If the coolant level drops within a short time of replenishing

Visually check the radiator, hoses, engine coolant reservoir cap, radiator cap, drain cock and water pump. If you cannot find a leak, have your Toyota dealer test the cap and check for leaks in the cooling system.

247

4-3. Do-it-yourself maintenance

CAUTION

■When the engine is hot

Do not remove the radiator cap. The cooling system may be under pressure and may spray hot coolant if the cap is removed, causing serious injuries, such as burns.

NOTICE

■When adding coolant

Coolant is neither plain water nor straight antifreeze. The correct mixture of water and antifreeze must be used to provide proper lubrication, corrosion protection and cooling. Be sure to read the antifreeze or coolant label.

■If you spill coolant

Be sure to wash it off with water to prevent it from damaging parts or paint.

Radiator and condenser

Check the radiator and condenser and clear away any foreign objects. If either of the above parts are extremely dirty or you are not sure of their condition, have your vehicle inspected by your Toyota dealer.

CAUTION

■When the engine is hot

Do not touch the radiator or condenser as they may be hot and cause serious injuries, such as burns.

248

Brake fluid

■ Checking fluid level

4-3. Do-it-yourself maintenance

The brake fluid level should be between the “MAX” and “MIN” lines on the tank.

■ Adding fluid Make sure to check the fluid type and prepare the necessary item.

Fluid type Item

FMVSS No.116 DOT 3 or SAE J1703 brake fluid Clean funnel

■Brake fluid can absorb moisture from the air

Excess moisture in the brake fluid can cause a dangerous loss of braking efficiency. Use only newly opened brake fluid.

CAUTION

■When filling the reservoir

Take care as brake fluid can harm your hands and eyes and damage painted surfaces. If fluid gets on your hands or in your eyes, flush the affected area with clean water immediately. If you still experience discomfort, consult a doctor.

249

4-3. Do-it-yourself maintenance

NOTICE

■If the fluid level is low or high

It is normal for the brake fluid level to go down slightly as the brake pads wear out or when the fluid level in the accumulator is high. If the reservoir needs frequent refilling, there may be a serious problem.

Battery

Check the battery as follows: ■ Battery exterior

Make sure that the battery terminals are not corroded and that there are no loose connections, cracks, or loose clamps.

Terminals Hold-down clamp

■ Checking battery fluid

250

LEVEL”

“UPPER

Check that the level is between the and “LOWER LEVEL” lines. “UPPER LEVEL” line “LOWER LEVEL” line If the fluid level is at or below the “LOWER LEVEL” line, add dis- tilled water.

4-3. Do-it-yourself maintenance

■ Adding distilled water

Low

O.K.

Remove the vent plug. Add distilled water. If the “UPPER LEVEL” line cannot be seen, check the fluid level by looking directly at the cell. Put the vent plug back on and close it securely.

■Before recharging

When recharging, the battery produces hydrogen gas which is flammable and explosive. Therefore, observe the following before recharging: ●If recharging with the battery installed on the vehicle, be sure to discon-

nect the ground cable.

●Make sure the power switch on the charger is off when connecting and

disconnecting the charger cables to the battery.

CAUTION

■Chemicals in the battery

Batteries contain poisonous and corrosive sulfuric acid and may produce hydrogen gas which is flammable and explosive. To reduce the risk of death or serious injury, take the following precautions while working on or near the battery: ●Do not cause sparks by touching the battery terminals with tools. ●Do not smoke or light a match near the battery. ●Avoid contact with eyes, skin and clothes.

251

4-3. Do-it-yourself maintenance

CAUTION

●Never inhale or swallow electrolyte. ●Wear protective safety glasses when working near the battery. ●Keep children away from the battery.

■Where to safety charge the battery

Always charge the battery in an open area. Do not charge the battery in a garage or closed room where there is insufficient ventilation.

■Emergency measures regarding electrolyte

●If electrolyte gets in your eyes

Flush your eyes with clean water for at least 15 minutes and get immedi- ate medical attention. If possible, continue to apply water with a sponge or cloth while traveling to the nearest medical facility.

●If electrolyte gets on your skin

Wash the affected area thoroughly. If you feel pain or burning, get medical attention immediately.

●If electrolyte gets on your clothes

It can soak through clothing on to your skin. Immediately take off the cloth- ing and follow the procedure above if necessary.

●If you accidentally swallow electrolyte

Drink a large quantity of water or milk. Get emergency medical attention immediately.

NOTICE

■When recharging the battery

Never recharge the battery while the engine is running. Also, be sure all accessories are turned off.

■When adding distilled water

Avoid overfilling. Water spilled during battery recharging may cause corro- sion.

252

Washer fluid

4-3. Do-it-yourself maintenance

If neither washer does not work or the low windshield washer fluid warning light comes on (if equipped), the washer tank may be empty. Add washer fluid to “FULL” line.

CAUTION

■When adding washer fluid

Do not add washer fluid when the engine is hot or running as washer fluid contains alcohol and may catch fire if spilled on the engine etc.

NOTICE

■Do not use any fluid other than washer fluid

Do not use soapy water or engine antifreeze instead of washer fluid. Doing so may cause streaking on the vehicle’s painted surfaces.

■Diluting washer fluid

Dilute washer fluid with water as necessary. Refer to the freezing temperatures listed on the label of the washer fluid bot- tle.

253

4-3. Do-it-yourself maintenance Tires

Replace or rotate tires in accordance with maintenance sched- ules and treadwear. ■ Checking tires

location of

New tread Treadwear indicator Worn tread The treadwear indicators is shown by the “TWI” or “ ” marks, etc., molded on the sidewall of each tire. Check spare tire condition and pressure if not rotated.

Rotate the tires in the order shown.

To equalize tire wear and extend tire life, Toyota recom- mends that tire rotation is carried out at the same inter- val as tire inspection. Vehicles with P195/50R16
tires: Do not fail to initialize the tire pressure warning system after tire rotation.

■ Tire rotation

Front

254

4-3. Do-it-yourself maintenance

■ Tire pressure warning system (if equipped)

Your vehicle is equipped with a tire pressure warning system that uses tire pressure warning valves and transmitters to detect low tire inflation pressure before serious problems arise. (→P. 307) The compact spare tire is not equipped with a tire pressure warning valve and transmitter.

Installing tire pressure warning valves and transmitters (vehicles with a tire pressure warning system)

When replacing tires or wheels, tire pressure warning valves and transmitters must also be installed. When new tire pressure warning valves and transmitters are installed, new ID codes must be registered in the tire pressure warning computer and the tire pressure warning system must be initialized. Have tire pres- sure warning valve and transmitter ID codes registered by your Toyota dealer. (→P. 256) ■ The tire pressure warning system must be initialized in the fol-

lowing circumstances: ● For vehicles with P195/50R16 tires, when rotating front and rear

tires which have different tire inflation pressures

● When the tire inflation pressure is changed such as when

changing traveling speed

When the tire pressure warning system is initialized, the current tire inflation pressure is set as the benchmark pressure.

■ How to initialize the tire pressure warning system

Park the vehicle in a safe place and turn the engine switch to the “LOCK” position. Initialization cannot be performed while the vehicle is moving.

255

4-3. Do-it-yourself maintenance

Adjust the tire pressure to the specified cold tire inflation pres- sure level. (→P. 351) Make sure to adjust the tire pressure to the specified cold tire inflation pressure level. The tire pressure warning system will operate based on this pressure level. Turn the engine switch to the “ON” position.

Press and hold the tire pressure warning reset switch until the tire pressure warning light blinks slowly 3 times.

Wait for a few minutes with the engine switch in the “ON” posi- tion and then turn the engine switch to the “LOCK” position.

Registering ID codes (vehicles with a tire pressure warning system)

The tire pressure warning valve and transmitter is equipped with a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID code. Have the ID code registered by your Toyota dealer.

■When to replace your vehicle’s tires

Tires should be replaced if: ●You have tire damage such as cuts, splits, cracks deep enough to

expose the fabric, and bulges indicating internal damage

●A tire goes flat repeatedly or cannot be properly repaired due to the

size or location of a cut or other damage

If you are not sure, consult with your Toyota dealer.

256

4-3. Do-it-yourself maintenance

■Replacing tires and wheels (vehicles with a tire pressure warning

system) If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work properly. After driving for about 20 minutes, the tire pressure warning light blinks for 1
minute and stays on to indicate a system malfunction.

■Tire life

Any tire over 6 years old must be checked by a qualified technician even if it has seldom or never been used or damage is not obvious.

■Routine tire inflation pressure checks (vehicles with a tire pressure

warning system) The tire pressure warning system does not replace routine tire inflation pressure checks. Make sure to check tire inflation pressure as part of your routine of daily vehicle checks.

■Low profile tires (vehicles with P195/50R16 tires)

Generally, low profile tires will wear more rapidly and tire grip perfor- mance will be reduced on snowy and/or icy roads when compared to standard tires. Be sure to use snow tires or tire chains on snowy and/or icy roads and drive carefully at a speed appropriate for road and weather conditions.

■Maximum load of tire

Check that the maximum load of the replacement tire is greater than 1/2
of the Gross Axle Weight Ratings (GAWR) of either the front axle or the rear axle, whichever is greater.

For the GAWR, see the Certification Label. For the maximum load of the tire, see the load limit at maximum cold tire inflation pressure mentioned on the sidewall of the tire. (→P. 356)

257

4-3. Do-it-yourself maintenance

■Tire types

●Summer tires

Summer tires are high-speed performance tires best suited to highway driving under dry conditions. Since summer tires do not have the same traction performance as snow tires, summer tires are inadequate for driving on snow-covered or icy roads. For driving on snow-covered roads or icy roads, the use of snow tires is recommended. When installing snow tires, be sure to replace all four tires.

●All season tires

All season tires are designed to provide better traction in snow and to be adequate for driving in most winter conditions as well as for use year-round. All season tires, however, do not have adequate traction performance compared with snow tires in heavy or loose snow. Also, all season tires fall short in acceleration and handling performance compared with summer tires in highway driving.

●Snow tires

For driving on snow-covered roads or icy roads, we recommend using snow tires. If you need snow tires, select tires of the same size, con- struction and load capacity as the originally installed tires. Since your vehicle has radial tires as original equipment, make sure your snow tires also have radial construction. Do not install studded tires without first checking local regulations for possible restrictions. Snow tires should be installed on all wheels. (→P. 172)

■Initializing the tire pressure warning system (vehicles with a tire

pressure warning system) Initialize the system with the tire inflation pressure adjusted to the speci- fied level.

■If the tread on snow tires wears down below 0.16 in. (4 mm)

The effectiveness of the tires as snow tires is lost.

■If you press the tire pressure warning reset switch accidentally

(vehicles with a tire pressure warning system) If initialization is performed, adjust the tire inflation pressure to the speci- fied level and initialize the tire pressure warning system again.

258

4-3. Do-it-yourself maintenance

■When the initialization of the tire pressure warning system has

failed (vehicles with a tire pressure warning system) Initialization can be completed in a few minutes. However, in the follow- ing cases, the settings has not been recorded and the system will not operate properly. If repeated attempts to record tire inflation pressure settings are unsuccessful, have the vehicle inspected by your Toyota dealer. ●When operating the tire pressure warning reset switch, the tire pres-

sure warning light does not blink 3 times.

●After driving for a certain period of time since the initialization has been completed, the warning light comes on after blinks for 1 minute.

■Tire pressure warning system certification

FCC ID: PAXPMVC010
FCC ID: HYQ23AAD For vehicles sold in U.S.A. NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsi- ble for compliance could void the user’s authority to operate the equip- ment.

259

4-3. Do-it-yourself maintenance

CAUTION

■When inspecting or replacing tires

Observe the following precautions to prevent accidents. Failure to do so may cause damage to parts of the drive train as well as dangerous handling characteristics, which may lead to an accident resulting in death or serious injury. ●Do not mix tires of different makes, models or tread patterns.

Also, do not mix tires of remarkably different treadwear.

●Do not use tire sizes other than those recommended by Toyota. ●Do not mix differently constructed tires (radial, bias-belted or bias-ply

tires).

●Do not mix summer, all season and snow tires. ●Do not use tires that have been used on another vehicle.

Do not use tires if you do not know how they were used previously.

●Do not tow if your vehicle has a compact spare tire installed.

■When initializing the tire pressure warning system (vehicles with a

tire pressure warning system) Do not operate the tire pressure warning reset switch without first adjust- ing the tire inflation pressure to the specified level. Otherwise, the tire pressure warning light may not come on even if the tire inflation pressure is low, or it may come on when the tire inflation pressure is actually nor- mal.

260

4-3. Do-it-yourself maintenance

NOTICE

■Repairing or replacing tires, wheels, tire pressure warning valves, transmitters and tire valve caps (vehicles with a tire pressure warn- ing system) ●When removing or fitting the wheels, tires or the tire pressure warning valves and transmitters, contact your Toyota dealer as the tire pres- sure warning valves and transmitters may be damaged if not handled correctly.

●When replacing tire valve caps, do not use tire valve caps other than

those specified. The cap may become stuck.

■To avoid damage to the tire pressure warning valves and transmit-

ters (vehicles with a tire pressure warning system) When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and transmitter when replacing the tire. (→P. 255)

■Driving on rough roads

Take particular care when driving on roads with loose surfaces or pot- holes. These conditions may cause losses in tire inflation pressure, reducing the cushioning ability of the tires. In addition, driving on rough roads may cause damage to the tires themselves, as well as the vehicle’s wheels and body.

■Low profile tires (vehicles with P195/50R16 tires)

Low profile tires may cause greater damage than usual to the tire wheel when sustaining impact from the road surface. Therefore, pay attention to the following: ●Be sure to use proper tire inflation pressure. If tires are under-inflated,

they may be damaged more severely.

●Avoid potholes, uneven pavement, curbs and other road hazards. Fail-

ure to do so may lead to severe tire and wheel damage.

■If tire inflation pressure of each tire becomes low while driving Do not continue driving, or your tires and/or wheels may be ruined.

261

4-3. Do-it-yourself maintenance Tire inflation pressure

■ Tire inflation pressure

The recommended cold tire inflation pressure and tire size are displayed on the tire and loading information label. (→P. 351)

262

4-3. Do-it-yourself maintenance

■ Inspection and adjustment procedure

Tire valve Tire pressure gauge

Remove the tire valve cap. Press the tip of the tire pressure gauge onto the tire valve. Read the pressure using the gauge gradations. If the tire inflation pressure is not at the recommended level, adjust the pressure. If you add too much air, press the center of the valve to deflate. After completing the tire inflation pressure measurement and adjustment, apply soapy water to the valve and check for leakage. Put the tire valve cap back on.

263

4-3. Do-it-yourself maintenance

■Tire inflation pressure check interval

You should check tire inflation pressure every two weeks, or at least once a month. Do not forget to check the spare.

■Effects of incorrect tire inflation pressure

Driving with incorrect tire inflation pressure may result in the following: ●Reduced fuel efficiency ●Reduced driving comfort and tire life ●Reduced safety ●Damage to the drive train If a tire needs frequent inflating, have it checked by your Toyota dealer.

■Instructions for checking tire inflation pressure

When checking tire inflation pressure, observe the following: ●Check only when the tires are cold.

If your vehicle has been parked for at least 3 hours or has not been driven for more than 1 mile or 1.5 km, you will get an accurate cold tire inflation pressure reading.

●Always use a tire pressure gauge.

The appearance of the tire can be misleading. In addition, tire infla- tion pressures that is even just a few pounds off can affect ride quality and handling.